Hollow cobalt ferrite–polyaniline nanofibers as magnetically separable visible-light photocatalyst for photodegradation of methyl orange

Investigation of Doehlert matrix conception in novel intrinsically conducting polymers based on selenium nanoparticles for wastewater treatment: Synthesis, characterization, kinetic and chemometric study

The synthesis of robust intrinsically conducting polymers (ICPs) based on nanoparticles is becoming increasingly attractive to the research community due to the unique properties of these nanocomposites. Indeed, as organic semiconductors, ICPs combine both polymer and metal properties in a single structure. This study presents an innovative approach in which the Doehlert Matrix (DM) is applied to a novel ICP nanocomposite based on polyaniline (Pani) coupled with selenium (Se) loaded mesoporous titania (TiO2) for wastewater treatment by photocatalysis. It includes both the elaboration routes of ICP nanocomposites, characterization of materials by X-ray diffraction (XRD), BET analysis, thermogravimetric analysis (TGA), RAMAN spectroscopy and Fourier transform infrared spectroscopy (FTIR) and photodegradation of methylene blue (MB) as a representative of dye pollutant. In addition, the photocatalytic process has been optimized by a novel DM conception. The effect of the pH of the solution, the catalyst dosage and the initial pollutant concentration was investigated. The optimum conditions were found to be: initial MB concentration of 15 mg/L, the catalyst dosage of 69 mg and pH of 9.6 with an operating time of 75 min, with a coefficient of determination R2 equal to 0.9985. The removal efficiency of BM was close to 97 %. The study shows that the new ICP nanocomposites improve the photocatalytic efficiency compared to pure titania and/or pure Pani. In addition, as the ternary Pani-Se-TiO2 nanocomposite could be obtained from a low-cost synthesis, it is a very promising material for use in wastewater treatment.

Vapor Phase Infiltration of Titanium Oxide into P3HT to Create Organic-Inorganic Hybrid Photocatalysts

Herein, we report for the first time the use of vapor phase infiltration (VPI) to infuse conducting polymers with inorganic metal oxide clusters that together form a photocatalytic material. While vapor infiltration has previously been used to electrically dope conjugated polymers, this is the first time, to our knowledge, that the resultant hybrid material has been demonstrated to have photocatalytic properties. The system studied is poly(3-hexylthiophene-2,5-diyl) (P3HT) vapor infiltrated with TiCl4 and H2O to create P3HT-TiOx organic-inorganic hybrid photocatalytic materials. X-ray photoelectron spectroscopy analysis shows that P3HT-TiOx VPI films consist of a partially oxidized P3HT matrix, and the infiltrated titanium inorganic is in a 4+ oxidation state with mostly oxide coordination. Upon visible light illumination, these P3HT-TiOx hybrids degrade methylene blue dye molecules. The P3HT-TiOx hybrids are 4.6× more photocatalytically active than either the P3HT or TiO2 individually or when sequentially deposited (e.g., P3HT on TiO2). On a per surface area basis, these hybrid photocatalysts are comparable or better than other best in class polymer semiconductor photocatalysts. VPI of TiCl4 + H2O into P3HT makes a unique hybrid structure and idealized photocatalyst architecture by creating nanoscale TiOx clusters concentrated toward the surface achieving extremely high catalytic rates. The mechanism for this enhanced photocatalytic rate is understood using photoluminescence spectroscopy, which shows significant quenching of excitons in P3HT-TiOx as compared to neat P3HT, indicating that P3HT acts as a photosensitizer for the TiOx catalyst sites in the hybrid material. This work introduces a new approach to designing and synthesizing organic-inorganic hybrid photocatalytic materials, with expansive opportunities for further exploration and optimization.

Synthesis and characterization of titanium-substituted nanocrystalline Co2-Y hexaferrite: magnetically retrievable photocatalyst for treatment of methyl orange contaminated wastewater

Rapid industrial growth causes considerable environmental havoc, adversely affecting human and aqueous life. It becomes a significant concern to deal with adequate wastewater treatment strategies by converging on water scarcity. This research work explored the synthesis of titanium-substituted Y-type barium hexaferrite (Co₂-Y), having a general formula of Ba₂Co₂Fe_12-xTi_xO₂₂ (x = 0.0, 0.1, 0.2, 0.3, 0.4, and 0.5), using a facile nitrate-based sol-gel auto-combustion route and its suitability was investigated as a heterogeneous catalyst within the photo-Fenton-based degradation of methyl orange (MO), one of the significant pollutants generated from textile industries. Developing a thermochemically stable and magnetically separable heterogeneous catalyst for photocatalytic decomposition of nonbiodegradable organic dye from wastewater was also emphasized. The as-prepared nanocrystalline Co₂-Y powders were analyzed using XRD, FTIR, DLS, UV-visible spectroscopy, SEM, VSM, and XPS. Furthermore, the photocatalytic degradation performance of pristine and titanium substituted Ba₂Co₂Fe_11.6Ti_0.4O₂₂ ferrite, having the lowest bandgap value among all samples, was quantified and compared in terms of apparent rate constant (k_arc) value and turnover frequency values. The enriched photocatalytic performance was correlated with the existence of multi-valance states of transition metal cations and the availability of oxygen vacancy, confirmed by the surface chemistry using the XPS analysis. The modified (enhanced thermal and chemical stability) hexaferrite catalyst was magnetically separable and reusable without significant losses to its catalytic performance. This promising catalyst may be considered as a replacement for soft ferrite materials to catalyze the degradation of several other nonbiodegradable organic pollutants from wastewater in large-scale industries.

Synthesis and Characterization of 2D-WS2 Incorporated Polyaniline Nanocomposites as Photo Catalyst for Methylene Blue Degradation

2D-WS₂ incorporated polyaniline nanocomposites (WS₂-PANI) with varying WS₂ loadings were synthesized by a facile in situ oxidative polymerization technique which effectively promoted photocatalytic waste-water remediation using methylene blue (MB) as the probe molecules. The physicochemical properties of WS₂-PANI (1-5) nanocomposites were investigated using multifarious techniques such as FT-IR, XRD, BET surface area, TGA, FESEM, and HRTEM. An electron microscopy analysis that was performed using HRTEM analysis confirm the layered structure of WS₂ with periodic planes (100) separated by 0.27 nm. The photocatalytic performance of the WS₂-PANI (1-5) for MB degradation performed under UV photo irradiation clearly showed that 2 wt.% WS₂-PANI outperformed other variants with 93% degradation MB within 90 min. Furthermore, the catalytic material was reusable for five cycles without a significant loss of the catalytic performance.

A Novel Trace-Level Ammonia Gas Sensing Based on Flexible PAni-CoFe2O4 Nanocomposite Film at Room Temperature

In this study, we developed a new chemi-resistive, flexible and selective ammonia (NH3) gas sensor. The sensor was prepared by depositing thin film of polyaniline-cobalt ferrite (PAni-CoFe2O4) nanocomposite on flexible polyethylene terephthalate (PET) through an in situ chemical oxidative polymerization method. The prepared PAni-CoFe2O4 nanocomposite and flexible PET-PAni-CoFe2O4 sensor were evaluated for their thermal stability, surface morphology and materials composition. The response to NH3 gas of the developed sensor was examined thoroughly in the range of 1-50 ppm at room temperature. The sensor with 50 wt% CoFe2O4 NPs content showed an optimum selectivity to NH3 molecules, with a 118.3% response towards 50 ppm in 24.3 s response time. Furthermore, the sensor showed good reproducibility, ultra-low detection limit (25 ppb) and excellent flexibility. In addition, the relative humidity effect on the sensor performance was investigated. Consequently, the flexible PET-PAni-CoFe2O4 sensor is a promising candidate for trace-level on-site sensing of NH3 in wearable electronic or portable devices.

Advanced Photocatalysts Based on Conducting Polymer/Metal Oxide Composites for Environmental Applications

Photocatalysts provide a sustainable method of treating organic pollutants in wastewater and converting greenhouse gases. Many studies have been published on this topic in recent years, which signifies the great interest and attention that this topic inspires in the community, as well as in scientists. Composite photocatalysts based on conducting polymers and metal oxides have emerged as novel and promising photoactive materials. It has been demonstrated that conducting polymers can substantially improve the photocatalytic efficiency of metal oxides owing to their superior photocatalytic activities, high conductivities, and unique electrochemical and optical properties. Consequently, conducting polymer/metal oxide composites exhibit a high photoresponse and possess a higher surface area allowing for visible light absorption, low recombination of charge carriers, and high photocatalytic performance. Herein, we provide an overview of recent advances in the development of conducting polymer/metal oxide composite photocatalysts for organic pollutant degradation and CO2 conversion through photocatalytic processes.

Recent advancements of spinel ferrite based binary nanocomposite photocatalysts in wastewater treatment

A lot of studies on spinel ferrites (MFe₂O₄, M = divalent metal ion) and their binary nanocomposites as photocatalysts in the decontamination of wastewater have been performed, because MFe₂O₄ nanoparticles are relatively stable, biocompatible and low-cost efficient photocatalyst. The separation of MFe₂O₄ photocatalyst is easy owing to its excellent magnetic behavior. With this background, the recent developments on photocatalytic performances of MFe₂O₄ based binary nanocomposites were comprehensively reviewed. Especially, a focus on MFe₂O₄/metal oxides, MFe₂O₄/carbon based materials, MFe₂O₄/polymers, MFe₂O₄/metal nanoparticles and MFe₂O₄/other compounds for the photocatalytic degradation of dyes, emerging contaminants and inorganic pollutants has been thoroughly given. The advantages of MFe₂O₄ based nanocomposites as photocatalysts were also discussed. In addition, the possible pathway of active free radical generation by these photocatalysts under visible and ultraviolet irradiation has been explained. A comparison of photocatalytic activities of MFe₂O₄ based binary nanocomposites with recent reports has been carried out. This review concludes that MFe₂O₄ based binary nanocomposites have potential capacity in water purification technology. Nevertheless, their practical utilization in water treatment plants still needs to be further studied.

Preparation and Magnetic Properties of CoFe2O4 Oriented Fiber Arrays by Electrospinning

The morphology of magnetic materials has a great influence on the properties, which is attributed to the magnetic anisotropy of the materials. Therefore, it is worth studying the fabrication of the aligned fiber and the change of its domain distribution. Nanoparticles and nanofibers were prepared by the hydrothermal and electrospinning methods, respectively. At the same time, the arranged nanofibers were collected by the drum collecting device. After the same annealing at 700 °C, it was found that the diameter of fibers collected by different collecting drums is similar. By studying the hysteresis loops of nanoarrays, it was found that they had strong anisotropy. The easy axis was parallel to the long axis, the Hc and Mr of the easy axis and the hard axis were 1330.5 Oe, 32.39 Am²/kg, and 857.2 Oe, 24.8 Am²/kg, respectively. Due to the anisotropy of the shape and the interaction between the particles, the Hc could not be enhanced. Therefore, the Ms and Hc of the nanoparticles were 80.23 Am²/kg and 979.3 Oe, respectively. The hysteresis loop and the change of magnetic moment during the demagnetization of the CoFe₂O₄ nanofiber array were simulated via micromagnetic software. The simulated Hc was 1480 Oe, which was similar to the experimental value.

Photosensitive Hybrid Nanostructured Materials: The Big Challenges for Sunlight Capture

Solar radiation is becoming increasingly appreciated because of its influence on living matter and the feasibility of its application for a variety of purposes. It is an available and everlasting natural source of energy, rapidly gaining ground as a supplement and alternative to the nonrenewable energy feedstock. Actually, an increasing interest is involved in the development of efficient materials as the core of photocatalytic and photothermal processes, allowing solar energy harvesting and conversion for many technological applications, including hydrogen production, CO2 reduction, pollutants degradation, as well as organic syntheses. Particularly, photosensitive nanostructured hybrid materials synthesized coupling inorganic semiconductors with organic compounds, and polymers or carbon-based materials are attracting ever-growing research attention since their peculiar properties overcome several limitations of photocatalytic semiconductors through different approaches, including dye or charge transfer complex sensitization and heterostructures formation. The aim of this review was to describe the most promising recent advances in the field of hybrid nanostructured materials for sunlight capture and solar energy exploitation by photocatalytic processes. Beside diverse materials based on metal oxide semiconductors, emerging photoactive systems, such as metal-organic frameworks (MOFs) and hybrid perovskites, were discussed. Finally, future research opportunities and challenges associated with the design and development of highly efficient and cost-effective photosensitive nanomaterials for technological claims were outlined.

Magnetically recyclable CoFe2O4/ZnO nanocatalysts for the efficient catalytic degradation of Acid Blue 113 under ambient conditions

CoFe₂O₄/ZnO magnetic nanocatalysts were synthesized using a low-frequency ultrasound-assisted technique to enhance the optical, morphological, magnetic and catalytic properties of ZnO. The as-synthesized nanocatalysts were characterized by XRD, Raman, TEM, DR-UV-Vis and VSM analyses in order to confirm the expected modifications of the resulting nanocatalysts. The Raman spectral analysis revealed substitutional Zn²⁺ in the CoFe₂O₄/ZnO nanocatalyst. The as-synthesized material was tested for its catalytic activity in the degradation of Acid Blue (AB113), a known textile pollutant. The CoFe₂O₄ and CoFe₂O₄/ZnO nanocatalysts revealed the efficient catalytic degradation of AB113 in ambient conditions. The nanocatalyst dosage and the initial concentration of AB113 were varied by fixing one parameter as constant in order to determine the maximum catalytic efficiency with the minimum catalyst loading for AB113 degradation. The CoFe₂O₄/ZnO nanocatalyst demonstrated 10-fold enhanced mineralization of AB113 compared to the individual bare nanocatalysts, which could be achieved within 3 hours of catalytic degradation of AB113. The magnetic CoFe₂O₄/ZnO nanocatalyst was found to be stable for six consecutive recycles of AB113 degradation, which indicates that the catalytic efficiency of the nanocatalyst was retained after various numbers of cycles.

CoFe₂O₄/ZnO magnetic nanocatalysts were synthesized using a low-frequency ultrasound-assisted technique to enhance the optical, morphological, magnetic and catalytic properties of ZnO.

Polyaniline/Reduced Graphene Oxide Composite-Enhanced Visible-Light-Driven Photocatalytic Activity for the Degradation of Organic Dyes

Creation of an innovative composite photocatalyst, to advance its performance, has attracted researchers to the field of photocatalysis. In this article, a new photocatalyst based on polyaniline/reduced graphene oxide (PANI/RGO) composites has been prepared via the in situ oxidative polymerization method employing RGO as a template. For thermoelectric applications, though a higher percentage (50 wt %) of RGO has been used, for photocatalytic activity, lesser percentages (2, 5, and 8 wt %) of RGO in the composite have given a significant outcome. Furthermore, photoluminescence (PL) spectra, time-resolved fluorescence spectra, and Brunauer-Emmett-Teller surface area analyses confirmed the improved photocatalytic mechanism. PANI/RGO composites under visible light irradiation exhibit amazingly improved activity toward the degradation of cationic and anionic dyes in comparison with pristine PANI or RGO. Here, a PANI/RGO composite, with 5 wt % RGO(PG2), has emerged as the best combination with the degradation percentages of 99.68, 99.35, and 98.73 for malachite green, rhodamine B, and congo red within 15, 30, and 40 min, respectively. Experimental findings show that the introduction of RGO can relieve the agglomeration of PANI nanoparticles and enhance the light absorption of the materials due to an increased surface area. Moreover, the PG2 composite also showed excellent photocatalytic activity to reduce noxious Cr(VI). The effective removal of Cr(VI) up to 94.7% at pH 2 was observed within only 15 min. With the help of the active species trapping experiment, a plausible mechanism for the photocatalytic degradation has been proposed. The heightened activity of the as-synthesized composite compared to that of neat PANI or RGO was generally because of high concentrations of ^•OH radicals and partly of ^•O₂ ^- and holes (h⁺) as concluded from the nitroblue tetrazolium probe test and photoluminescence experiment. It is hoped that the exceptional photocatalytic performance of our work makes the conducting polymer-based composite an effective alternative in wastewater treatment for industrial applications.

Recent Developments about Conductive Polymer Based Composite Photocatalysts

Conductive polymers have been widely investigated in various applications. Several conductive polymers, such as polyaniline (PANI), polypyrrole (PPy), poly(3,4-ethylenedioxythiophene) (PEDOT)), and polythiophene (PTh) have been loaded with various semiconductor nanomaterials to prepare the composite photocatalysts. However, a critical review of conductive polymer-based composite photocatalysts has not been available yet. Therefore, in this review, we summarized the applications of conductive polymers in the preparation of composite photocatalysts for photocatalytic degradation of hazardous chemicals, antibacterial, and photocatalytic hydrogen production. Various materials were systematically surveyed to illustrate their preparation methods, morphologies, and photocatalytic performances. The synergic effect between conductive polymers and semiconductor nanomaterials were observed for a lot of composite photocatalysts. The band structures of the composite photocatalysts can be analyzed to explain the mechanism of their enhanced photocatalytic activity. The incorporation of conductive polymers can result in significantly improved visible-light driven photocatalytic activity by enhancing the separation of photoexcited charge carriers, extending the light absorption range, increasing the adsorption of reactants, inhibiting photo-corrosion, and reducing the formation of large aggregates. This review provides a systematic concept about how conductive polymers can improve the performance of composite photocatalysts.

Bridging the gap between laboratory and application in photocatalytic water purification

Despite a large number of publications in the field, photocatalytic water treatment is still somewhat disconnected from real world application and we highlight recent developments to address this.

A magnetically recyclable photocatalyst with commendable dye degradation activity at ambient conditions

An efficient, economical, environment-friendly and easy separable catalyst to treat environmental contaminants is an enduring attention in recent years due to their great potential for environmental protection and remediation. Here we have reported the excellent performance of polyaniline activated heterojunctured Ni_0.5Zn_0.5Fe₂O₄ catalyst to degrade azo dye in an aqueous solution at ambient condition. The catalyst was prepared via a simple facile polymerization procedure. The physicochemical properties and structure of the synthesized catalyst was confirmed by TGA, PXRD, FTIR, SEM, HRTEM, XPS, EDX, and DRS techniques. The developed catalyst has shown an accelerated degradation ability of an organic pollutant Orange ll Sodium salt azo dye about 100% for the dye concentration of 50 ppm within five minutes at ambient conditions with 1 g/l loading of catalyst. Simple facile synthesis, easy separation by an external magnet, good reusability and high degradation capability of the catalyst may promote the practical applications of the heterostructured catalyst at ambient condition for water remediation. The present study also explored possible credible charge transfer directions and mechanism of photocatalysis supported by trapping experiments and electrochemical impedance spectroscopy (EIS) measurement for the effective improvement of photocatalytic activity and enhancement of the visible light adsorption.

The Electrospun Ceramic Hollow Nanofibers

Hollow nanofibers are largely gaining interest from the scientific community for diverse applications in the fields of sensing, energy, health, and environment. The main reasons are: their extensive surface area that increases the possibilities of engineering, their larger accessible active area, their porosity, and their sensitivity. In particular, semiconductor ceramic hollow nanofibers show greater space charge modulation depth, higher electronic transport properties, and shorter ion or electron diffusion length (e.g., for an enhanced charging-discharging rate). In this review, we discuss and introduce the latest developments of ceramic hollow nanofiber materials in terms of synthesis approaches. Particularly, electrospinning derivatives will be highlighted. The electrospun ceramic hollow nanofibers will be reviewed with respect to their most widely studied components, i.e., metal oxides. These nanostructures have been mainly suggested for energy and environmental remediation. Despite the various advantages of such one dimensional (1D) nanostructures, their fabrication strategies need to be improved to increase their practical use. The domain of nanofabrication is still advancing, and its predictable shortcomings and bottlenecks must be identified and addressed. Inconsistency of the hollow nanostructure with regard to their composition and dimensions could be one of such challenges. Moreover, their poor scalability hinders their wide applicability for commercialization and industrial use.