Batch adsorption of cephalexin antibiotic from aqueous solution by walnut shell-based activated carbon

Influence of cephalexin on cadmium adsorption onto microplastic particles in water: Human health risk evaluation

This paper explores the impact of environmental factors on the adsorption of cadmium (Cd) and cephalexin (CEX) onto polyethylene (PE) microplastics. The study focused on Cd adsorption behavior on microplastics (MPs) of various sizes, revealing that particles sized 30-63 μm exhibited the highest adsorption capacity compared to other sizes. Cd sorption was significantly influenced by initial pH and salinity levels. Experimental data closely matched both the Langmuir (R2 > 0.91) and Freundlich (R2 > 0.92) isotherms. Cd adsorption onto PE particles was greater than CEX adsorption, with the maximum Cd uptake capacity measured at 1.8 mg/g. FTIR analysis indicated that Cd and CEX adsorption onto MPs was likely governed by physical interactions, as no new functional groups were detected post-uptake. The desorption rates of Cd and CEX from PE microplastics were evaluated in various liquids, including aqueous solution, tap water, seawater, and synthetic gastric juice. The health risks associated with Cd, in combination with MPs and CEX, for both children and adults were assessed in groundwater and aqueous solutions. This study offers scientific insights and guidelines for examining the environmental behavior, migration, and transformation of microplastics and their related ecological risks in scenarios of combined pollution.

Removal of the Highly Toxic Anticoccidial Monensin Using Six Different Low-Cost Bio-Adsorbents

The anticoccidial monensin (MON) is a high-concern emerging pollutant. This research focused on six low-cost bio-adsorbents (alfa, cactus, and palm fibers, and acacia, eucalyptus, and zean oak barks), assessing their potential for MON removal. Batch adsorption/desorption tests were carried out, and the results were fitted to the Freundlich, Langmuir, Linear, Sips, and Temkin models. The concentrations adsorbed by the six materials were very similar when low doses of antibiotic were added, while they differed when adding MON concentrations higher than 20 µmol L-1 (adsorption ranging 256.98-1123.98 μmol kg-1). The highest adsorption corresponded to the sorbents with the most acidic pH (<5.5) and the highest organic matter and effective cation exchange capacity values (eucalyptus bark and acacia bark, reaching 92.3% and 87.8%), whereas cactus and palm fibers showed the lowest values (18.3% and 10.17%). MON desorption was below 8.5%, except for cactus and palm fibers. Temkin was the model showing the best adjustment to the experimental data, followed by the Langmuir and the Sips models. The overall results indicate that eucalyptus bark, alfa fiber, and acacia bark are efficient bio-adsorbents with potential for MON removal, retaining it when spread in environmental compartments, reducing related risks for human and environmental health.

Valorization and Upcycling of Acid Mine Drainage and Plastic Waste via the Preparation of Magnetic Sorbents for Adsorption of Emerging Contaminants

Plastic waste poses a serious environmental risk, but it can be recycled to produce a variety of nanomaterials for water treatment. In this study, poly(ethylene terephthalate) (PET) waste and acid mine drainage were used in the preparation of magnetic mesoporous carbon (MMC) nanocomposites for the adsorptive removal of pharmaceuticals and personal care products (PPCPs) from water samples. The latter were then characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and ζ potential. The results of Brunauer-Emmett-Teller isotherms revealed high specific surface areas of 404, 664, and 936 m2/g with corresponding pore sizes 2.51, 2.28, and 2.26 nm for MMC, MMAC-25%, and MMAC-50% adsorbents, respectively. Under optimized conditions, the equilibrium studies were best described by the Langmuir and Freundlich models and kinetics by the pseudo-second-order model. The maximum adsorption capacity for monolayer adsorption from the Langmuir model was 112, 102, and 106 mg/g for acetaminophen, caffeine, and carbamazepine, respectively. The composites could be reused for up to six cycles without losing their adsorption efficiency. Furthermore, prepared adsorbents were used to remove acetaminophen, caffeine, and carbamazepine from wastewater samples, and up to a 95% removal efficiency was attained.

Zinc oxide nanoparticles encapsulated in alginate beads: a promising and recyclable adsorbent for simultaneous uptake of toxic metals

Heavy metal toxicity is a known problem and various methods are used for treatment. Adsorption has some advantages and it would be promising if environmentally friendly and cheap materials were utilized. Alginate and zinc oxide nanoparticles were selected and composite alginate beads were used for the removal of mixed metals from aqueous solutions. Batch and column experiments were conducted to determine some parameters' effects and the adsorbent's real application potential. According to the batch experiments, zinc oxide nanoparticles to alginate ratio of 0.5 g g-1, and pH levels nearby to the neutral range led to better metal removals. 0.5 ml min-1of flow rate supplied better metal removal efficiencies in columns, with the highest treatment as 86% of Pb2+. Acid treatment can be successfully applied for the regeneration of the adsorbent, at least three times only with a 4% reduction in the adsorption efficiency. Heavy metal uptake was compatible with the pseudo 2nd order model indicating chemisorption as a dominant mechanism. Also, the intraparticle diffusion model illustrated adsorption might govern more than one step. The Langmuir model had the best fit and suggested monolayer covering for Pb2+, 76.3 mg g-1. Alginate-based nanocomposite beads were useful for mixed metal removal and could be used.

Amoxicillin removal from water by adsorption on activated carbon of mineral sources: discussion of experimental data, mechanisms and modeling

The use of antibiotics has increased considerably in the last decades in human medicine, as well as agriculture and animal production. Consequently, high loads of these emerging contaminants in the environment can increase antibiotic-resistant genes and the development of multi-resistant pathogenic microorganisms. This work aims to evaluate the removal of amoxicillin trihydrate in aqueous medium using mineral-activated carbon of bituminous origin as an adsorbent. The adsorbent was classified as microporous with associated mesopores, showing phenolic groups on its surface, which indicates the versatility of the adsorbent. The adsorption kinetics and isotherms were predominantly chemical. Pseudo-second-order model, as well as LDF model adjusted to the kinetic data. Sips and Langmuir isotherms adjusted to the adsorption equilibrium data. The maximum adsorptive capacity obtained experimentally was 313.30 mg g-1 at 50°C. The thermodynamic properties suggested spontaneous, monolayer, and endothermic adsorption. Overall, compared to previous works, the adsorbent proved to be a viable and promising alternative for the removal of antibiotics from water, with high adsorption capacity of amoxicillin, without being necessary to perform any prior changes to the material.

Parameter Influence, Characterization and Adsorption Mechanism Studies of Alkaline-Hydrolyzed Garcinia kola Hull Particles for Cr(VI) Sequestration

Despite the regulations by The World Health Organization (WHO) on the permissible limit of chromium, many industries still discharge wastewater polluted with chromium into the environment irrationally. This poses a lot of risk to aquatic lives and humans because of its carcinogenic and toxic attributes. Thus, treatment of industrial wastewater polluted with chromium is highly imperative before its disposal. Nonetheless, the hulls generated from Garcinia kola in our various farmlands also causes environmental pollution when dumped unknowingly. In this present study, Garcinia kola hull particles (GK-HP) was hydrolyzed using NaOH and applied as adsorbent for Cr(VI) sequestration. The raw Garcinia kola hull particles (rGK-HP) and modified Garcinia kola hull particles (cMGK-HP) were characterized using Brunauer-Emmett-Teller (BET) method, scanning electron microscopy (SEM), powder X-ray diffractometry (XRD), Fourier-Transform-Infrared (FTIR), thermogravimetric analysis (TGA), energy dispersive spectroscopy (EDS) and point of zero charge (pHpzc). The influence of pH, adsorbent dose, contact time, temperature and adsorbate initial concentration on Cr(VI) sequestration were examined. The cMGK-HP was able to remove 96.25% of Cr(VI) from solution and proved to be effective than rGK-HP. The amount of Cr(VI) removed from solution decreased as the pH and adsorbate initial concentration were increased. However, the amount increased as the adsorbent dose, contact time and temperature were increased. Change in morphological structure, textural property, spectral peak, phase composition and adsorbents chemical composition before and after Cr(VI) sequestration from solution were proved by SEM, BET, FTIR, XRD, and EDS analyses respectively. The isotherm and kinetic studies suggest Cr(VI) adsorption on adsorbents' surface to be monolayer in nature and adsorption data to be well-fitted into pseudo second order model respectively. The cMGK-HP possessed excellent reusability attribute and high thermal stability as shown by TGA. In conclusion, cMGK-HP could effectively be used as an adsorbent for Cr(VI) sequestration from solution.

Insights in Pharmaceutical Pollution: The Prospective Role of eDNA Metabarcoding

Environmental pollution is a growing threat to natural ecosystems and one of the world's most pressing concerns. The increasing worldwide use of pharmaceuticals has elevated their status as significant emerging contaminants. Pharmaceuticals enter aquatic environments through multiple pathways related to anthropogenic activity. Their high consumption, insufficient waste treatment, and the incapacity of organisms to completely metabolize them contribute to their accumulation in aquatic environments, posing a threat to all life forms. Various analytical methods have been used to quantify pharmaceuticals. Biotechnology advancements based on next-generation sequencing (NGS) techniques, like eDNA metabarcoding, have enabled the development of new methods for assessing and monitoring the ecotoxicological effects of pharmaceuticals. eDNA metabarcoding is a valuable biomonitoring tool for pharmaceutical pollution because it (a) provides an efficient method to assess and predict pollution status, (b) identifies pollution sources, (c) tracks changes in pharmaceutical pollution levels over time, (d) assesses the ecological impact of pharmaceutical pollution, (e) helps prioritize cleanup and mitigation efforts, and (f) offers insights into the diversity and composition of microbial and other bioindicator communities. This review highlights the issue of aquatic pharmaceutical pollution while emphasizing the importance of using modern NGS-based biomonitoring actions to assess its environmental effects more consistently and effectively.

Taguchi Parametric Optimization and Cost Analysis of Hexavalent Chromium Sequestration From Aqueous Solution by NaOH-Modified Garcinia kola Hull Particles

The presence of chromium in industrial wastewater is unavoidable due to its large usage as part of chemical constituents used in many industries. Its removal from wastewater is imperative because it's toxic in nature. This study investigated the application of NaOH-modified Garcinia kola hull particles (cMGK-HP) for Cr(VI) sequestration from aqueous solution. The optimization of process parameters was executed using Taguchi of Design Expert software for optimum point prediction, analysis of variance, parameters interaction and mathematical model development. A proposed model was used for the adsorption cost analysis. The predicted and experimental percentage of Cr(VI) sequestration were recorded at optimum point to be 99.02% and 98.76% with pH, adsorbent dose, contact time, initial concentration, and temperature of 2, 8 g/L, 20 minutes, 10 mg/L, and 20°C respectively. A correlation coefficient of .9937 between experimental and predicted values of percentage Cr(VI) sequestration affirmed high efficacy of the developed model. ANOVA showed the order of parameter contribution to be pH > adsorbent dose > initial concentration > contact time > temperature. A maximum adsorption capacity of 217.39 mg g-1 was obtained for cMGK-HP. Cost analysis revealed using cMGK-HP to be cost effective for Cr(VI) sequestration with a total operational cost of 0.824 $/mole Cr(VI) ions when compared with commercial activated carbon. Adsorbent characterization revealed the presence of active functional groups enhancing the sequestration process. It could be deduced that cMGK-HP is effective to remove Cr(VI) from solution.

Metal organic framework-derived recyclable magnetic coral Co@Co3O4/C for adsorptive removal of antibiotics from wastewater

The menace posed by antibiotic contamination to humanity has increased due to the absence of efficient antibiotic removal processes in the conventional waste water treatment methods from the hospitals, households, animal husbandry, and pharma industry. Importantly, only a few commercially available adsorbents are magnetic, porous, and have the ability to selectively bind and separate various classes of antibiotics from the slurries. Herein, we report the synthesis of a coral-like Co@Co3O4/C nanohybrid for the remediation of three different classes of antibiotics - quinolone, tetracycline, and sulphonamide. The coral like Co@Co3O4/C materials are synthesized via a facile room temperature wet chemical method followed by annealing in a controlled atmosphere. The materials demonstrate an attractive porous structure with an excellent surface-to-mass ratio of 554.8 m2 g-1 alongside superior magnetic responses. A time-varying adsorption study of aqueous nalidixic acid solution on Co@Co3O4/C nanohybrids indicates that these coral-like Co@Co3O4/C nanohybrids could achieve a high removal efficiency of 99.98% at pH 6 in 120 min. The adsorption kinetics data of Co@Co3O4/C nanohybrids follow a pseudo-second-order reaction kinetics suggesting a chemisorption effect. The adsorbent has also shown its merit in reusability for four adsorption-desorption cycles without showing significant change in the removal efficiency. More in-depth studies validate that the excellent adsorption capability of Co@Co3O4/C adsorbent attributing to the electrostatic and π-π interaction between adsorbent and various antibiotics. Concisely, the adsorbent manifests the potential for the removal of a wide range of antibiotics from the water alongside showing their utility in the hassle-free magnetic separation.

Chitosan-Hydroxyapatite Bio-Based Composite in Film Form: Synthesis and Application in Wastewater

Water purification from toxic metals was the main objective of this work. A composite in film form was prepared from the biomaterials hydroxyapatite, chitosan and glycerol using the dissolution/recrystallization method. A nanoparticle-based film with a homogenous and smooth surface was produced. The results of total reflectance infrared spectroscopy (ATR-FTIR) and thermal gravimetric analysis (TGA/DTA) demonstrated the presence of a substantial physical force between composite components. The composite was tested for its ability to absorb Cd2+ and Zn2+ ions from aqueous solutions. Cd2+ and Zn2+ adsorption mechanisms are fit using the Langmuir model and the pseudo-second-order model. Thermodynamic parameters indicated that Cd2+ and Zn2+ ion adsorption onto the composite surface is spontaneous and preferred at neutral pH and temperatures somewhat higher than room temperature. The adsorption studies showed that the maximum adsorption capacity of the HAp/CTs bio-composite membrane for Cd2+ and Zn2+ ions was in the order of cadmium (120 mg/g) > Zinc (90 mg/g) at an equilibrium time of 20 min and a temperature of 25 °C. The results obtained on the physico-chemical properties of nanocomposite membranes and their sorption capacities offer promising potential for industrial and biological activities.

Biosorptive Removal of Ethacridine Lactate from Aqueous Solutions by Saccharomyces pastorianus Residual Biomass/Calcium Alginate Composite Beads: Fixed-Bed Column Study

In this study, ethacridine lactate removal from aqueous solution using a biosorbent material based on residual microbial biomass and natural polymers in fixed-bed continuous column was investigated. Composite beads of Saccharomyces pastorianus residual biomass and calcium alginate were obtained by immobilization technique. The prepared biosorbent was characterized by Fourier transformed infrared spectroscopy, scanning electron microscopy, and analysis of point of zero charge value. Then, laboratory-scale experiments by fixed-bed column biosorption were conducted in continuous system. To this purpose, the column bed high (5 cm; 7.5 cm), initial pollutant concentration (20 mg/L; 40 mg/L), and solution flow through the column (0.6 mL/min; 1.5 mL/min) were considered the main parameters. Recorded breakthrough curves suggest that lower flow rates, greater bed heights, and a lower concentration of ethacridine lactate led to an increased biosorption of the target compound. The biosorption dynamic was investigated by nonlinear regression analysis using the Adams–Bohart, Yoon–Nelson, Clark, and Yan mathematical models. Conclusively, our research highlights, firstly, that the obtained biosorbent material has the required properties for retaining the ethacridine lactate from aqueous solution in continuous system. Secondly, it emphasizes that the modeling approach reveals an acceptable fitting with the experimental data for the Yoon–Nelson, Clark, and Yan models.

Environmental-Friendly Adsorbent Composite Based on Hydroxyapatite/Hydroxypropyl Methyl-Cellulose for Removal of Cationic Dyes from an Aqueous Solution

The aim of this study is to develop a new, efficient, and inexpensive natural-based adsorbent with high efficacy for the cationic dye methylene blue (MB). A natural-based nanocomposite based on hydroxyapatite (HAp) and hydroxypropyl methylcellulose (HPMC) was selected for this purpose. It was synthesized by the dissolution/reprecipitation method. A film with a homogeneous and smooth surface composed of nanoparticles was prepared from the nanocomposite. HPMC and HAp biopolymers were selected due to their compatibility, biodegradability, and non-toxicity. Total reflectance infrared spectroscopy (ATR-FTIR), scanning electron microscopy (SEM), and calorimetric/thermal gravimetric (DSC/TGA) analysis results revealed the existence of strong physical interaction between the composite components. Scanning electron microscopy (SEM) observations show a composite sheet with a homogenous and smooth surface, indicating excellent compatibility between HPMC and HAp in the composite. The nanocomposite was evaluated as an adsorbent for organic dyes in an aqueous solution. The effects of solution pH, initial MB concentration, composite concentration, and adsorption time on the adsorption efficiency were evaluated. The highest adsorption rate was seen as 52.0 mg of MB/g composite. The adsorption rate reached equilibrium in about 20 min. Fitting of the adsorption data to the Langmuir and Freundlich adsorption models was investigated. Results showed that the adsorption process follows the Langmuir isotherm model. The kinetic study results revealed that the adsorption process was pseudo-second-order. The herein composite is an excellent alternative for use as contemporary industrial-scale adsorbents.

Efficiency of the bank filtration technique for diclofenac removal: A review

Bank filtration (BF) has been employed for more than a century for the production of water with a better quality, and it has been showing satisfactory results in diclofenac attenuation. Considered the most administered analgesic in the world, diclofenac has been frequently detected in water bodies. Besides being persistent in the environment, this compound is not completely removed by the conventional water treatments, drinking water treatment plants (DWTPs) and wastewater treatment plant (WWTPs). BF has a high complexity, whose efficiency depends on the characteristics of the observed pollutant and on the environment where the system in installed, which is why this is a topic that has been constantly studied. Nevertheless, studies present the behavior of diclofenac during the BF process. In this context, this research performed the evaluation of the factors and the biogeochemical processes that influence the efficiency of the BF technique in diclofenac removal. The aerobic conditions, higher temperatures, microbial biomass density, hydrogen potential close to neutrality and sediments with heterogeneous fractions are considered the ideal conditions in the aquifer for diclofenac removal. Nonetheless, there is no consensus on which of these factors has the greatest contribution on the mechanism of attenuation during BF. Studies with columns in laboratory and modeling affirm that the highest degradation rates occur in the first centimeters (5-50 cm) of the passage of water through the porous medium, in the environment known as hyporheic zone, where intense biogeochemical activities occur. Research has shown 100% removal efficiency for diclofenac persistent to compounds not removed during the BF process. However, half of the studies had removal efficiency that ranged between 80 and 100%. Therefore, the performance of more in-depth studies on the degradation and mobility of this compound becomes necessary for a better understanding of the conditions and biogeochemical processes which act in its attenuation.

HKUST-1 derived carbon adsorbents for tetracycline removal with excellent adsorption performance

As the abuse of antibiotics has led to increasingly serious environmental pollution problems, studies have found that the adsorption method can be used to efficiently and quickly remove residual antibiotics in water with low cost and high efficiency. Metal-organic frameworks and their derived porous carbons have received widespread attention as a new type of adsorption material. In this study, HKUST-1 was synthesized by a hydrothermal method and carbonized to HDC-350 at 350 °C under an oxygen-free atmosphere. Through adsorption experiments, HDC-350 is found to show a superior adsorption effect for tetracycline (TC), with an adsorption capacity that reaches 136.88 mg g^-1. The TC adsorption mechanism was studied through characterization and analysis of HDC-350. The adsorption of TC by HDC-350 mainly relies on electrostatic attraction, hydrogen bonding, metal-organic complexation, and intermolecular interactions. This study shows that HKUST-1-derived porous carbon can be used to improve the water stability of HKUST-1, and, at the same time, can effectively adsorb TC in solution, which provides good conditions for practical research applications in the future.

Application of activated carbon functionalized with graphene oxide for efficient removal of COVID-19 treatment-related pharmaceuticals from water

Currently, the COVID-19 pandemic has been increasing the consumption of some drugs, such as chloroquine (CQN) and dipyrone (DIP), which are continuously discharged into water resources through domestic sewage treatment systems. The presence of these drugs in water bodies is worrisome due to their high toxicity, which makes crucial their monitoring and removal, especially by means of advanced technologies. Given this scenario, a new adsorbent material was synthesized through the combination of babassu coconut activated carbon and graphene oxide (GAC-GO). This study was evaluated in batch adsorption processes, aiming at the treatment of water contaminated with CQN and DIP. Characterization analyzes using physicochemical and spectroscopic techniques indicated that the GAC-GO functionalization was successfully performed. The equilibrium time of the adsorption process was 18 and 12 h for CQN and DIP, respectively. Kinetic and isothermal data better fitted to pseudo-second-order and Langmuir models for both drugs. Thermodynamic parameters showed that the process is endothermic and the maximum adsorption capacities of CQN and DIP were 37.65 and 62.43 mg g-1, respectively, both at 318 K. The study of the effect of ionic strength, which simulates a real effluent, demonstrated that the synthesized adsorbent has potential application for the treatment of effluents. Furthermore, satisfactory removal rates were verified for the removal of other contaminants in both simple solutions and synthetic mixtures, evidencing the versatile profile of the adsorbent.

Applications of Computational and Statistical Models for Optimizing the Electrochemical Removal of Cephalexin Antibiotic from Water

One of the most serious effects of micropollutants in the environment is biological magnification, which causes adverse effects on humans and the ecosystem. Among all of the micro-pollutants, antibiotics are commonly present in the aquatic environment due to their wide use in treating or preventing various diseases and infections for humans, plants, and animals. Therefore, an aluminum-based electrocoagulation unit has been used in this study to remove cephalexin antibiotics, as a model of the antibiotics, from water. Computational and statistical models were used to optimize the effects of key parameters on the electrochemical removal of cephalexin, including the initial cephalexin concentration (15–55 mg/L), initial pH (3–11), electrolysis time (20–40 min), and electrode type (insulated and non-insulated). The response surface methodology-central composite design (RSM-CCD) was used to investigate the dependency of the studied variables, while the artificial neural network (ANN) and adaptive neuro-fuzzy inference system (ANFIS) methods were applied for predicting the experimental training data. The results showed that the best experimental and predicted removals of cephalexin (CEX) were 88.21% and 93.87%, respectively, which were obtained at a pH of 6.14 and electrolysis time of 34.26 min. The results also showed that the ANFIS model predicts and interprets the experimental results better than the ANN and RSM-CCD models. Sensitivity analysis using the Garson method showed the comparative significance of the variables as follows: pH (30%) > electrode type (27%) > initial CEX concentration (24%) > electrolysis time (19%).

Low-Cost and Eco-Friendly Hydroxyapatite Nanoparticles Derived from Eggshell Waste for Cephalexin Removal

This work describes the hydroxyapatite nanoparticle (HAP) preparation from eggshell waste and their application as an adsorbent for Cephalexin (Ceph) antibiotic removal from aqueous solutions. Chemical precipitation with phosphoric acid was used to evaluate the feasibility of calcium oxide for HAP preparation. The structural properties of HAP were characterized by X-ray diffraction, which revealed the formation of the hydroxyapatite crystalline phase formation. In addition, transmitting electron spectroscopy showed an irregular shape with a variation in size. The impact of various experimental conditions on the removal efficiency such as the solution’s pH, contact time, HAP mass, solution temperature, and Ceph concentration were studied. Experimental data showed that HAP could remove most Ceph species from aqueous solutions within 1 h at pH = 7 with 70.70% adsorption efficiency utilizing 50 mg of the HAP. The removal process of Ceph species by HAP was kinetically investigated using various kinetic models, and the results showed the suitability of the pseudo-second-order kinetic model for the adsorption process description. Moreover, the removal process was thermodynamically investigated; the results showed that the removal was spontaneous endothermic and related to the randomness increase. The data confirmed that HAP had high efficiency in removing Ceph antibiotics from an aqueous solution.

Removal of Hydroxychloroquine Using Engineered Biochar from Algal Biodiesel Industry Waste: Characterization and Design of Experiment (DoE)

Adsorption of hydroxychloroquine (HCQ) onto H₃PO₄-activated Cystoseira barbata (Stackhouse) C. Agardh (derived from algal biodiesel industry waste) biochar was investigated via batch experiments and mathematical models. The activated biochar (BC-H) was produced in a single step by using the microwave irradiation method. Thus, it was obtained with a low cost, energy efficiency and by promoting clean production processes. BC-H exhibited a remarkable adsorption efficiency (98.9%) and large surface area (1088.806 m² g⁻¹) for removal of HCQ. The Langmuir isotherm and the pseudo-second-order kinetic models were the best fit for the equilibrium adsorption and kinetics experiments, and the maximum monolayer adsorption capacity (qmax) was found to be 353.58 µg g⁻¹. Additionally, the experiments with real wastewater showed that BC-H's ability to adsorb HCQ was not affected by competitive ions in the water. The Taguchi orthogonal array (L16 OA) experimental design was applied for the effective cost optimization analyses of the adsorption process by considering four levels and four controllable factors (initial pH, HCQ concentration, amount of adsorbent and contact time). Scanning electron microscopy, Fourier transform infrared spectroscopy and Brunauer–Emmett–Teller analyses were used for characterizing the adsorbent. The findings showed that BC-H can be used as an effective and low-cost adsorbent in the removal of HCQ from water.

Cephalexin removal by a novel Cu-Zn bionanocomposite biosynthesized in secondary metabolic products of Aspergillus arenarioides EAN603 with pumpkin peels medium: Optimization, kinetic and artificial neural network models

The present study aimed to investigate the removal efficiency of cephalexin (CFX) by a novel Cu-Zn bionanocomposite biosynthesized in the secondary metabolic products of Aspergillus arenarioides EAN603 with pumpkin peels medium (CZ-BNC-APP). The optimization study was performed based on CFX concentrations (1, 10.5 and 20 ppm); CZ-BNC-APP dosage (10, 55 and 100 mg/L); time (10, 55 and 100 min), temperature (20, 32.5 and 45 °C). The artificial neural network (ANN) model was used to understand the CFX behavior for the factors affecting removal process. The CZ-BNC-APP showed an irregular shape with porous structure and size between 20 and 80 nm. The FTIR detected CC, C-O and OH groups. ANN model revealed that CZ-BNC-APP dosage exhibited the vital role in the removal process, while the removal process having a thermodynamic nature. The CFX removal was optimized with 12.41 ppm CFX, 60.60 mg/L of CZ-BNC-APP, after 97.55 min and at 35 °C, the real maximum removal was 95.53% with 100.52 mg g^-1 of the maximum adsorption capacity and 99.5% of the coefficient. The adsorption of CFX on CZ-BNC-APP was fitted with pseudo-second-order model and both Langmuir and Freundlich isotherms models. These findings revealed that CZ-BNC-APP exhibited high potential to remove CFX.

Investigation of the Conditions for Preconcentration of Cadmium Ions by Solid Phase Extraction Method Using Modified Juglans regia L. Shells

BACKGROUND

Juglans regia L. shells as agricultural waste can be considered as alternative sorbents to minimize the problems associated with heavy metal pollution.

OBJECTIVE

In this study, J. regia shells (JRS) and JRS modified with hydrazine hydrate (JRS-HH) were used as sorbents and compared for the preconcentration of Cd(II) ions from aqueous solution.

METHODS

For the characterization of sorbents, scanning electron microscopy and energy dispersive X-ray (SEM/EDX) analysis and Fourier transform infrared (FTIR) spectroscopy were used. For preconcentration, the solid phase extraction (SPE) technique was used. Preconcentration studies were performed by column method and pH, eluent type and concentration, sample volume, flow rate, and interfering ions effect were studied to determine the optimum column parameters.

RESULTS

The limit of detection (LOD) of the sorbents (JRS and JRS-HH) are 0.31 and 0.18 µg/L, respectively. According to the Langmuir isotherm model for both sorbents, for JRS KL = 0.030 L/mg, R2 = 0.992, 0.016 L/mg, and for JRS-HH KL = 0.016 L/mg, R2 = 0.998 and maximum adsorption capacities of the sorbents were found to be as 29.6 and 65.7 mg/g, respectively. The mean recoveries and RSD values at a 95% confidence level (N = 6) for Cd(II) were 100.9% and 3.42, and 100.6% and 3.79, for the JRS and JRS-HH sorbents, respectively.

CONCLUSIONS

Using this method good results were obtained when compared with those in the literature and the proposed method was successfully applied to the analysis of the certificated reference material (NIST 1640).

HIGHLIGHTS

JRS are an effective and inexpensive sorbent for the preconcentration of metal ions when modified. Thus, low-cost agricultural wastes are both recovered and have an economic value.

Sustainable approaches for removal of cephalexin antibiotic from non-clinical environments: A critical review

In this article, the removal of cephalexin (CFX) antibiotic from non-clinical environment is reviewed. Adsorption and photocatalytic degradation techniques are widely used to remove CFX from waters and wastewaters, the combination of these methods is becoming more common for CFX removal. The treatment methods of CFX has not been reviewed before, the present article aim is to organize the scattered available information regarding sustainable approaches for CFX removal from non-clinical environment. These include adsorption by nanoparticles, bacterial biomass, biodegradation by bacterial enzymes and the photocatalysis using different catalysts and Photo-Fenton photocatalysis. The metal-organic frameworks (MOFs) appeared to have high potential for CFX degradation. It is evident from the recently papers reviewed that the effective methods could be used in place of commercial activated carbon. The widespread uses of photocatalytic degradation for CFX remediation are strongly recommended due to their engineering applicability, technical feasibility, and high effectiveness. The adsorption capacity of the CFX is ranging from 7 mg CFX g^-1 of activated carbon nanoparticles to 1667 mg CFX g^-1 of Nano-zero-valent iron from Nettle. In contrast, the photo-degradation was 45% using Photo-Fenton while has increased to 100% using heterogeneous photoelectro-Fenton (HPEF) with UVA light using chalcopyrite catalyst.

Application of Saccharomyces cerevisiae/Calcium Alginate Composite Beads for Cephalexin Antibiotic Biosorption from Aqueous Solutions

Cephalexin (CPX) is recognized as a water pollutant, and it has been listed in a number of countries with a risk factor greater than one. Herein, the present work focused on the synthesis, characterization and biosorption capacity evaluation of Saccharomyces cerevisiae immobilized in calcium alginate as a biosorbent to remove CPX from aqueous solutions. Biosorbent was characterized by SEM and FTIR techniques. Batch biosorption experiments were conducted in order to evaluate the effect of the initial pH, biosorbent dose and CPX initial concentration. The removal efficiency, in considered optimal conditions (pH = 4, CPX initial concentration = 30 mg/L, biosorbent dose = 1 g/L) was 86.23%. CPX biosorption was found to follow the pseudo–second-order kinetics. The equilibrium biosorption data were a good fit for the Langmuir model with correlation coefficient of 0.9814 and maximum biosorption capacity was 94.34 mg/g. This study showed that the synthesized biosorbent by immobilization technique is a low-cost one, easy to obtain and handle, eco-friendly, with high feasibility to remove CPX antibiotic from aqueous solution. The findings of this study indicate that the biosorbents based on microorganisms immobilized on natural polymers have the potential to be applied in the treatment of wastewater.

Comprehensive review on surfactant adsorption on mineral surfaces in chemical enhanced oil recovery

With the increasing demand for efficient extraction of residual oil, enhanced oil recovery (EOR) offers prospects for producing more reservoirs' original oil in place. As one of the most promising methods, chemical EOR (cEOR) is the process of injecting chemicals (polymers, alkalis, and surfactants) into reservoirs. However, the main issue that influences the recovery efficiency in surfactant flooding of cEOR is surfactant losses through adsorption to the reservoir rocks. This review focuses on the key issue of surfactant adsorption in cEOR and addresses major concerns regarding surfactant adsorption processes. We first describe the adsorption behavior of surfactants with particular emphasis on adsorption mechanisms, isotherms, kinetics, thermodynamics, and adsorption structures. Factors that affect surfactant adsorption such as surfactant characteristics, solution chemistry, rock mineralogy, and temperature were discussed systematically. To minimize surfactant adsorption, the chemical additives of alkalis, polymers, nanoparticles, co-solvents, and ionic liquids are highlighted as well as implementing with salinity gradient and low salinity water flooding strategies. Finally, current trends and future challenges related to the harsh conditions in surfactant based EOR are outlined. It is expected to provide solid knowledge to understand surfactant adsorption involved in cEOR and contribute to improved flooding strategies with reduced surfactant loss.

Carbamazepine and Diclofenac Removal Double Treatment: Oxidation and Adsorption

In the present research, the effect of two hybrid treatments, ozone followed by powdered activated carbon (PAC) or PAC followed by ozone (O₃), was studied for the removal of two drugs present in water: diclofenac and carbamazepine. In the study, two initial concentrations of each of the contaminants, 0.7 mg L^-1 and 1.8 mg L^-1, were used. Different doses of PAC between 4-20 mg L^-1 were studied as variables, as well as different doses of O₃ between 0.056-0.280 mg L^-1. The evolution of the concentration of each contaminant over time was evaluated. From the results obtained, it was concluded that the combined treatment with ozone followed by PAC reduces between 50% and 75% the time required to achieve 90% removal of diclofenac when compared with the time required when only activated carbon was used. In the case of carbamazepine, the time required was 97% less. For carbamazepine, to achieve reduction percentages of up to 90%, O₃ treatment followed by PAC acted faster than PAC followed by O₃. In the case of diclofenac, PAC treatment followed by O₃ was faster to reach concentrations of up to 90%. However, to reach yields below 80%, O₃ treatment followed by PAC was more efficient.

Degradation of micropollutant cephalexin by ultraviolet (UV) and assessment of residual antimicrobial activity of transformation products

Cephalexin (CEX) is an antibiotic commonly used to treat bacterial infections in humans and animals. However, it is also a micropollutant. Thus, this study evaluated the degradation of CEX using ultraviolet irradiation (UV-C) and analyzed the by-products as well as their residual antimicrobial activity. A reactor with a mercury vapor lamp was used for the degradation. Irradiated CEX solutions were collected over a period of 4 hours and analyzed using high-performance liquid chromatography coupled with mass spectrometry. For the residual antimicrobial activity the susceptibility test was performed using Staphylococcus aureus and Escherichia coli microorganisms by broth microdilution. It was found that CEX, after treatment, generated a metabolite with a mass of 150 m/z in 15 min. A four- and eightfold increase in the minimum inhibitory concentration of the drug against S. aureus and E. coli could be observed, respectively, after 20 min. Therefore, this treatment proved to be effective in the degradation of CEX, being able to degrade 81% of the initial molecule of the drug in 20 min. Furthermore, the antimicrobial activity of the CEX solution decreased as the irradiation time increased, indicating loss of antimicrobial function of the initial CEX molecule and the resulting by-products.

Evaluating the Removal of the Antibiotic Cephalexin from Aqueous Solutions Using an Adsorbent Obtained from Palm Oil Fiber

This study aimed to understand the adsorption process of cephalexin (CPX) from aqueous solution by a biochar produced from the fiber residue of palm oil. Scanning electron microscopy, Fourier transform infrared spectroscopy, Boehm titration, and the point of zero charge were used to characterize the morphology and surface functional groups of the adsorbent. Batch tests were carried out to evaluate the effects of the solution pH, temperature, and antibiotic structure. The adsorption behavior followed the Langmuir model and pseudo-second-order model with a maximum CPX adsorption capacity of 57.47 mg g^-1. Tests on the thermodynamic behavior suggested that chemisorption occurs with an activation energy of 91.6 kJ mol^-1 through a spontaneous endothermic process. Electrostatic interactions and hydrogen bonding represent the most likely adsorption mechanisms, although π-π interactions also appear to contribute. Finally, the CPX removal efficiency of the adsorbent was evaluated for synthetic matrices of municipal wastewater and urine. Promising results were obtained, indicating that this adsorbent can potentially be applied to purifying wastewater that contains trace antibiotics.

Caffeine removal from aqueous media by adsorption: An overview of adsorbents evolution and the kinetic, equilibrium and thermodynamic studies

Caffeine is an emerging pollutant and is considered the most representative pollutant of the Pharmaceutical Active due to its high consumption by the general population. It can be used to track pollution caused by humans. Different technologies have been employed to remove the caffeine from aqueous media, however the adsorption has been preferred due to its simplicity, high removal efficiency, operational and implementation facility and low cost. This paper provides a systematic review of the published peer-reviewed literature concerned with caffeine removal by the adsorption process. The Scopus and ScienceDirect databases were used to identify relevant articles researches on caffeine removal. Many authors have studied caffeine's adsorption equilibrium in aqueous media, different conditions, and different adsorbents. This paper aims to uncover the overall trend of adsorbent used, kinetic and thermodynamic studies. The impact of pH, temperature, adsorbent dosage and competitive effect were presented and analyzed. It was observed that the adsorption capacities ranged between 10 and 1000 mg g^-1, according to the nature and properties of the adsorbent. The pseudo-second order (kinetic model) and the Langmuir isotherm model showed the best adjustment of the experimental data from caffeine adsorption in most studies. The mechanistic understanding of adsorption and the development of new adsorbents are still a matter of future research, as well as the use of other kinetic models based on statistical factors and the thermodynamic studies should be considered.

Efficient removal of diclofenac and cephalexin from aqueous solution using Anthriscus sylvestris-derived activated biochar

The objective of this study was to investigate the adsorption of diclofenac (DF) and cephalexin (CPX) by Anthriscus sylvestris-derived activated biochar. The raw biochar (R-BC) and activated biochar (ACT-B) were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy and elemental analyses techniques to obtain information regarding the morphology, functional groups and elements of the adsorbents. Batch studies were carried out to examine the effect of various operational parameters. The maximum adsorption capacity of ACT-B was 392.94 mg g^-1 for DF and 724.54 mg g^-1 for CPX. The removal of DF and CPX was influenced by temperature and the co-existing ions. The kinetic data fitted well with the pseudo-second-order kinetic model, whereas the isotherm data showed the best correlation with Langmuir isotherm model. Electrostatic adsorption, hydrophobic interaction and π-π bonding play a key role in adsorption of both adsorbates by ACT-B. Additionally, column studies were conducted using ACT-B at different flow rates and different concentrations of DF and CPX to investigate the practical applicability of ACT-B in removal of the target contaminants. Thus, this study provides a feasible approach to synthesize activated biochar that can minimize pharmaceuticals pollution in water bodies.

Using basic parameters to evaluate adsorption potential of alternative materials: example of amoxicillin adsorption by activated carbon produced from termite bio-waste

The minimum set of parameters that can be used to assess the adsorption capacity of activated carbon (AC) produced from termite bio-waste was determined. Three types of AC were prepared: AC600 at 600 °C, MAC600 at the same temperature and impregnated with FeCl₃, and AC800 at 800 °C. The influence of the solution pH on the adsorption, adsorption kinetics, isotherms and thermodynamic parameters was considered to characterize the amoxicillin (AMX) adsorption process. The AC materials had surface areas (m² g^-1) of approximately 248.8 for AC600, 501.6 for AC800 and 269.5 for MAC600, with point of zero charge (pH_PZC) values of 8.3, 7.5 and 1.7, respectively. A time period of 30 min was chosen for the adsorption kinetics, which was best represented by the pseudo-first-order model for AC600, the intraparticle diffusion model for AC800 and the pseudo-second-order model for MAC600. Regarding the isotherms, a maximum adsorption of 23.4 mg g^-1 was found for AC800. In general, the thermodynamic parameters demonstrated a non-spontaneous process. It seems that the medium conditions, the adsorbate and adsorbent characteristics, and the Gibbs free energy are the most important parameters to be considered in a preliminary assessment of the adsorption efficiency of specific adsorbent/adsorbate pairs.

Adsorptive removal of apramycin antibiotic from aqueous solutions using Tween 80-and Triton X-100 modified clinoptilolite: experimental and fixed-bed modeling investigations

This study examined the performance of natural clinoptilolite (NC) modified with two surfactants of Triton X-100 (NC-Triton) and Tween 80 (NC-Tween) on apramycin (APR) adsorption from wastewater in batch and continues systems. The optimum pH, contact time, adsorbent dosage, and temperature were achieved. The findings revealed that the sorption was best described using the Langmuir isotherm compared to other isotherms. The maximum adsorption capacity of NC-Triton was greater than NC and NC-Tween. The lumped method was applied to solve the fixed-bed equations; predict breakthrough curve; determine axial dispersion coefficient and overall mass transfer coefficient parameters; and compare theoretical results with experimental results. Good fitness of experimental data with kinetic models of intra-particle diffusion, pseudo-first-order/liquid film diffusion and pseudo-second-order for NC, NC-Tween and NC-Triton, respectively, indicated that they were more suitable than the other models. Endothermic and spontaneous processes were resulted from positive enthalpy and negative Gibbs free energy changes, respectively.

Combination of solar photo-Fenton and adsorption process for removal of the anticancer drug Flutamide and its transformation products from hospital wastewater

The anti-cancer drug Flutamide (FLUT) is widely used and is of great environmental concern. The solar photo-Fenton (SPF) process can be an effective treatment for the removal of this type of micropollutant. The use of a single addition of 5 mg L^-1 of Fe²⁺ and 50 mg L^-1 of H₂O₂ achieved 20% primary degradation and only 3.05% mineralization. By using three additions of 5 mg L^-1 Fe²⁺, with an initial H₂O₂ concentration of 150 mg L^-1, 58% primary degradation was achieved, together with 12.07% mineralization. Consequently, thirteen transformation products (TPs) were formed. The SPF process was further combined with adsorption onto avocado seed activated carbon (ASAC) as an environmentally friendly approach for the removal of remained FLUT and the TPs. Doehlert design was used to assess the behavior of 13 TPs by optimizing the contact time and the adsorbent mass load. The optimal conditions for removal of FLUT and the TPs were 14 mg of ASAC and a contact time of 40 min. Remained FLUT and the TPs were totally removed using the adsorption process. The mechanisms of adsorption of FLUT and the TPs were strongly influenced by their polarity and π-π interactions of the TPs onto ASAC.

Recent advances in the use of walnut (Juglans regia L.) shell as a valuable plant-based bio-sorbent for the removal of hazardous materials

The effective use of agricultural by-products is definitely a major challenge in waste management. In the walnut fruit processing industry, large amounts of shells are produced as agricultural by-products and discarded or burned produced as fuel. Walnut (Juglans regia L.) is a valuable tree nut in the Juglandaceae family. The fruit is composed of four main parts: the kernel, the skin, the shell, and the husk. The importance of walnuts is mostly related to theirs valuable kernels. However, their shells are currently experiencing as much interest as their kernels due to the beneficial effects of the shells. In the past several years, walnut shell (WS) has been widely explored as a naturally inert plant-based biosorbent. In this review, we first highlight recent scientific literature regarding the development of adsorbents from WS in the form of carbon-based materials including unmodified/modified WS, and activated carbons (ACs). Next, we discuss the potential applications of WS-derived by-products as natural yet effective adsorbents for the removal of various hazardous materials including heavy metals (HMs), synthetic industrial dyes, and harmful chemicals.

Adsorption of cephalexin in aqueous media by graphene oxide: kinetics, isotherm, and thermodynamics

The present study proposes the synthesis and characterization of graphene oxide (GO) and its application in the adsorption of the antibiotic cephalexin (CFX) in aqueous solution. The characterization of graphene oxide was obtained by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and zeta potential. The influence of pH on the batch adsorption process was investigated by analysing adsorption equilibrium isotherms and adsorption kinetics. The images obtained by SEM and TEM presented the typical morphology attributed to GO sheets. The kinetic adsorption tests showed that equilibrium was reached in 420 min, and an adsorption capacity of 164 mg g^-1 was obtained. The models that best fit the experimental data were pseudo-second as well as the Langmuir isotherm. Therefore, GO was effective for removing the CFX antibiotic from aqueous solution by using a batch adsorption process.

Removal of Pharmaceutical Contaminants in Wastewater Using Nanomaterials: A Comprehensive Review

BACKGROUND

The limitless presence of pharmaceutical contaminants in discharged wastewater has emerged as a threat to aquatic species and humans. Their presence in drinking water has although raised substantial concerns, very little is known about the fate and ecological impacts of these pollutants. As a result, these pollutants are inevitably introduced to our food chain at trace concentrations. Unfortunately, the conventional wastewater treatment techniques are unable to treat pharmaceuticals completely with practical limitations. The focus has now been shifted towards nanotechnology for the successful remediation of these persistent pollutants. Thus, the current review specifically focuses on providing readers brief yet sharp insights into applications of various nanomaterials for the removal of pharmaceutical contaminants.

METHODS

An exhaustive collection of bibliographic database was done with articles having high impact and citations in relevant research domains. An in-depth analysis of screened papers was done through standard tools. Studies were categorized according to the use of nanoscale materials as nano-adsorbents (graphene, carbon nanotubes), nanophotocatalysts (metal, metal oxide), nano-filtration, and ozonation for promising alternative technologies for the efficient removal of recalcitrant contaminants.

RESULTS

A total of 365 research articles were selected. The contemporary advancements in the field of nanomaterials for drinking and wastewater treatment have been thoroughly analyzed along with their future perspectives.

CONCLUSION

The recommendations provided in this article will be useful to adopt novel strategies for on-site removal of the emerging contaminants in pharmaceutical effluents and related industries.

Development of microcrystalline cellulose based hydrogels for the in vitro delivery of Cephalexin

Three hydrogels namely, microcrystalline cellulose (MCC), microcrystalline cellulose-carboxymethyl cellulose (MCC-CMC) and microcrystalline cellulose-xylan (MCC-xylan) are synthesized using ethylene glycol diglycidyl ether as crosslinker. For the chemical characterization, FT-IR spectroscopy is adopted, whereas gel fraction and swelling ratio are used for the physical characterization of the hydrogels. Coarse morphology of hydrogels is further visualized by microscopic observation. The rheological characterization proves that MCC-CMC gel withstands higher strain to resist permanent deformation than the other two gels. The hydrogels are used for the loading and in vitro release of Cephalexin. The in vitro delivery is carried out in various simulated body fluids such as phosphate buffer saline (PBS), artificial intestinal fluid (AIF) and artificial gastric fluid (AGF). MCC-CMC is observed to deliver Cephalexin individually 15% in AGF, 86% in AIF, 98% in PBS and 98% in consecutive buffers (AGF followed by AIF and PBS).