Heterogeneous photo Fenton-like degradation of cibacron brilliant red 3B-A dye using amorphous Fe 78 Si 9 B 13 and Fe 73.5 Si 13.5 B 9 Cu 1 Nb 3 alloys: The influence of adsorption

Nanomaterials as a Sustainable Choice for Treating Wastewater: A Review

The removal of dyes from textile effluents utilizing advanced wastewater treatment methods with high efficiency and low cost has received substantial attention due to the rise in pollutants in water. The purpose of this work is to give a comprehensive analysis of the different treatments for removing chemical dyes from textile effluents. The capability and potential of conventional treatments for the degradation of dyeing compounds in aqueous media, as well as the influence of multiple parameters, such as the pH solution, initial dye concentration, and adsorbent dose, are presented in this study. This study is an overview of the scientific research literature on this topic, including nanoreductive and nanophotocatalyst processes, as well as nanoadsorbents and nanomembranes. For the purpose of treating sewage, the special properties of nanoparticles are currently being carefully researched. The ability of nanomaterials to remove organic matter, fungus, and viruses from wastewater is another benefit. Nanomaterials are employed in advanced oxidation techniques to clean wastewater. Additionally, because of their small dimensions, nanoparticles have a wide effective area of contact. Due to this, nanoparticles' adsorption and reactivity are powerful. The improvement of nanomaterial technology will be beneficial for the treatment of wastewater. This report also offers a thorough review of the distinctive properties of nanomaterials used in wastewater treatment, as well as their appropriate application and future possibilities. Since only a few types of nanomaterials have been produced, it is also important to focus on their technological feasibility in addition to their economic feasibility. According to this study, nanoparticles (NPs) have a significant adsorption area, efficient chemical reactions, and electrical conductivity that help treat wastewater effectively.

Fenton-like Remediation for Industrial Oily Wastewater Using Fe78Si9B13 Metallic Glasses

Metallic glasses (MGs) with a unique atomic structure have been widely used in the catalytic degradation of organic pollutants in the recent years. Fe78Si9B13 MGs exhibited excellent catalytic performance for the degradation of oily wastewater in a Fenton-like system for the first time. The oil removal and chemical oxygen demand (COD) removal from the oily wastewater were 72.67% and 70.18% within 60 min, respectively. Quenching experiments were performed to verify the production of active hydroxyl radicals (·OH) by activating hydrogen peroxide (H2O2). The formation of ·OH species can significantly contribute to the degradation reaction of oily wastewater. Fe78Si9B13 MG ribbons were highly efficient materials that exhibited superior reactivity towards H2O2 activation in oily wastewater treatment. The study revealed the catalytic capability of metallic glasses, presenting extensive prospects of their applications in oily wastewater treatment.

Environmental Remediation of Toxic Organic Pollutants Using Visible-Light-Activated Cu/La/CeO2/GO Nanocomposites

Environmental pollution is a major threat that increases day by day due to various activities. A wide variety of organic pollutants enter the environment due to petrochemical activities. Organic contamination can be unsafe, oncogenic, and lethal. Due to environmental issues worldwide, scientists and research communities are focusing their research efforts on this area. For the removal of toxic organic pollutants from the environment, photocatalysis-assisted degradation processes have gained more attention than other advanced oxidation processes (AOPs). In this manuscript, we report a novel photocatalysis of copper and lanthanum incorporating cerium oxide (CeO2) loaded on graphene oxide (Cu/La/CeO2/GO) nanocomposites successfully synthesized by hydrothermal techniques. XRD results showed the presence of dopant ions and a crystalline structure. FESEM images showed that the surface morphology of the synthesized nanocomposites formed a rod-like structure. The highlight of this study is the in-situ synthesis of the novel Cu/La/CeO2/GO nanocomposites, which manifest higher photodegradation of harmful organic dyes (Rhodamine B (RhB), Sunset Yellow (SY), and Cibacron Red (CR)). In Cu/La/CeO2/GO nanocomposites, the dopant materials restrict the rapid recombination of photoinduced electron-hole pairs and enhance the photocatalytic activity. The degradation percentages of RhB, SY, and CR dye solution are 80%, 60%, and 95%, respectively. In summary, the synthesized nanocomposites degrade toxic organic dyes with the help of visible light and are suitable for future industrial applications.

Discoloration of methylene blue at neutral pH by heterogeneous photo-Fenton-like reactions using crystalline and amorphous iron oxides

Different iron oxides were evaluated for the discoloration of methylene blue (MB) at neutral pH by heterogeneous photo-Fenton-like reactions with a UV-LED lamp. Fe3O4, α-Fe2O3, and a-FeOOH catalysts were synthesized and characterized by X-ray diffraction, scanning electron microscopy (SEM), Raman spectroscopy, Fourier transform infrared spectroscopy, and adsorption isotherms of N2. The results show high crystallinity and relatively low surface areas for Fe3O4 and α-Fe2O3, and amorphous structure with high surface area for the case of a-FeOOH. The discoloration of MB by iron oxides as catalysts was studied using UV-Vis spectroscopy. Despite the relative high adsorption of MB for magnetite (12%) compared to the other oxides, it shows a slow discoloration kinetics. Besides, amorphous oxide (named a-FeOOH) shows a higher discoloration kinetics with negligible adsorption capacity. The pseudo first-order kinetic constant values for Fe3O4, α-Fe2O3, and a-FeOOH are 5.31 × 10−3, 6.89 × 10−3, and 13.01 × 10−3 min−1; and the discoloration efficiencies at 120 min were 56, 60, and 82%, respectively. It was testified that low crystallinity iron oxide can be used in the efficient discoloration of MB by photo-Fenton process with a hand UV-A lamp.

S-doped NiFe-based catalyst for fast degradation of methylene blue by heterogeneous photo-Fenton reaction

S-doped NiFe-based particles were prepared by a solvothermal method and used to degrade methylene blue (MB) aqueous solutions with visible light in a heterogeneous Fenton reaction. The obtained solid samples were characterized by XRD, SEM, TEM, and XPS. It was found that 0.2 g L-1 NiFe2S4 can degrade 99.8% MB solution within 6 min in the presence of 5 mM H2O2 and natural pH. The recycle experiments results indicate that the NiFe2S4 catalyst possessed better stability than NiFe2O4. Furthermore, NiFe2S4 particles can be easily separated from contaminant solution by using a magnet due to their excellent ferromagnetism. COD analysis experiments indicated that the COD removal rate of NiFe2S4 is 73.1% in 30 min. A possible mechanism was proposed, and the degradation products were measured by LC-MS.

Design and perspective of amorphous metal nanoparticles from laser synthesis and processing

Amorphous metal nanoparticles (A-NPs) have aroused great interest in their structural disordering nature and combined downsizing strategies (e.g. nanoscaling), both of which are beneficial for highly strengthened properties compared to their crystalline counterparts. Conventional synthesis strategies easily induce product contamination and/or size limitations, which largely narrow their applications. In recent years, laser ablation in liquid (LAL) and laser fragmentation in liquid (LFL) as "green" and scalable colloid synthesis methodologies have attracted extensive enthusiasm in the production of ultrapure crystalline NPs, while they also show promising potential for the production of A-NPs. Yet, the amorphization in such methods still lacks sufficient rules to follow regarding the formation mechanism and criteria. To that end, this article reviews amorphous metal oxide and carbide NPs from LAL and LFL in terms of NP types, liquid selection, target elements, laser parameters, and possible formation mechanism, all of which play a significant role in the competitive relationship between amorphization and crystallization. Furthermore, we provide the prospect of laser-generated metallic glass nanoparticles (MG-NPs) from MG targets. The current and potential applications of A-NPs are also discussed, categorized by the attractive application fields e.g. in catalysis and magnetism. The present work aims to give possible selection rules and perspective on the design of colloidal A-NPs as well as the synthesis criteria of MG-NPs from laser-based strategies.

Role of Nanocrystallites of Al-Based Glasses and H2O2 in Degradation Azo Dyes

Al-based metallic glasses have a special atomic structure and should have a unique degradation ability in azo dye solutions. The Al₈₈Ni₉Y₃ (Y3), Al₈₅Ni₉Y₆ (Y6) and Al₈₂Ni₉Y₉ (Y9) glassy ribbons are melt spun and used in degrading methyl orange (MO) azo dye solution with adding H₂O₂. With increasing c_Y, the as-spun ribbons have an increasing GFA (glass formability) and gradually decreased the degradation rate of MO solution. TEM (transmission electron microscopy) results show that the Y3 ribbon has nano-scale crystallites, which may form the channels to transport elements to the surface for degrading the MO solution. After adding H₂O₂, the degradation efficiency of Al-based glasses is improved and the Y6 ribbon has formed nano-scale crystallites embedded in the amorphous matrix and it has the largest improvement in MO solution degradation. These results indicate that forming nano-scale crystallites and adding H₂O₂ are effective methods to improve the degradation ability of Al-based glasses in azo dye solutions.

Role of Boron in Enhancing Electron Delocalization to Improve Catalytic Activity of Fe-Based Metallic Glasses for Persulfate-Based Advanced Oxidation

Metallic glasses (MGs) with superior catalytic performance have recently been recognized as attractive candidates for wastewater treatment. However, further improving their performance will require knowledge of how to precisely regulate their electronic structures via compositional control. Here, two Fe-based MGs (Fe₇₈Si₉B₁₃ and Fe₈₀Si₉B₁₁) were prepared to compare how slightly altering boron content affected their electronic structure and catalytic performance. Density functional theory revealed that the Fe₇₈Si₉B₁₃ MG with 2 atom % higher boron exhibits an attractive electron delocalization, a high persulfate adsorption energy, and a superb work function due to precise regulation of the electronic structure, leading to exceptional degradation performance for seven organic pollutants. Furthermore, it can be reused 23 times without significant deterioration of catalytic performance, amorphous structure, and surface morphology. This work provides a new paradigm for the fundamental theory explaining how electronic structure is controlled by composition, creating a solid foundation to explore novel catalysts for water treatment.

High MB Solution Degradation Efficiency of FeSiBZr Amorphous Ribbon with Surface Tunnels

The as spun amorphous (Fe₇₈Si₉B₁₃)_99.5Zr_0.5 (Zr0.5) and (Fe₇₈Si₉B₁₃)₉₉Zr₁ (Zr1) ribbons having a Fenton-like reaction are proved to bear a good degradation performance in organic dye wastewater treatment for the first time by evaluating their degradation efficiency in methylene blue (MB) solution. Compared to the widely studied (Fe₇₈Si₉B₁₃)₁₀₀Zr₀ (Zr0) amorphous ribbon for degradation, with increasing c_Zr (Zr atomic content), the as-spun Zr0, Zr0.5 and Zr1 amorphous ribbons have gradually increased degradation rate of MB solution. According to δc (characteristic distance) of as-spun Zr0, Zr0.5 and Zr1 ribbons, the free volume in Zr1 ribbon is higher Zr0 and Zr0.5 ribbons. In the reaction process, the Zr1 ribbon surface formed the 3D nano-porous structure with specific surface area higher than the cotton floc structure formed by Zr0 ribbon and coarse porous structure formed by Zr0.5 ribbon. The Zr1 ribbon’s high free volume and high specific surface area make its degradation rate of MB solution higher than that of Zr0 and Zr0.5 ribbons. This work not only provides a new method to remedying the organic dyes wastewater with high efficiency and low-cost, but also improves an application prospect of Fe-based glassy alloys.

Visible-light-driven photo-Fenton degradation of organic pollutants by a novel porphyrin-based porous organic polymer at neutral pH

Developing novel heterogeneous photo-Fenton catalysts with high efficiency and stability, driven by visible-light rather ultraviolet light at neutral pH has been a major challenge for degradation of organic pollutants. In this work, we successfully synthesized a metalloporphyrin-based porous organic polymer (FePPOP-1) by the Sonogashira cross-coupling reaction. UV-vis absorption spectra showed FePPOP-1 exhibits a significant coverage of the natural solar irradiance spectrum. As a result, the prepared FePPOP-1 has a significantly enhanced photocatalytic activity for the visible-light-driven degradation of methylene blue. By using only 4 mg of FePPOP-1 as a catalyst, it was found that 50 mL of organic wastewater containing 70 ppm MB could be totally degraded in 80 min even at neutral pH. The effects of the initial MB, H₂O₂ concentrations, pH value and common ions on MB degradation were studied in detail. Both the catalytic mechanism of FePPOP-1 and the degradation route of MB were also proposed.

Fe-Based Metallic Glasses and Dyes in Fenton-Like Processes: Understanding Their Intrinsic Correlation

Fe-based metallic glasses have been demonstrated as effective heterogeneous catalysts in Fenton-like processes for dye degradation. Yet, currently corresponding studies have limitations due to the limited study object (dyes) and the correlation between metallic glasses and dye pollutants in Fenton-like processes is still not comprehensively studied. Accordingly, this work intensively investigated the thermal catalytic behavior correlations between two Fe-based metallic glasses (Fe78Si9B13 and Fe73.5Si13.5B9Cu1Nb3) and eight different dyes. Results indicated a lower activation energy in the more active metallic glass and a dependence of the activation energy of Fe-based metallic glasses in dye solutions. In addition, a high H2O2 concentration led to a declined catalytic efficiency but a photo-enhanced Fenton-like process overcame this limitation at high concentration of H2O2 due to the decrease of pH and enhancement of irradiation. Furthermore, the average mineralization rates of Fe78Si9B13 and Fe73.5Si13.5B9Cu1Nb3 have been measured to be 42.7% and 12.6%, respectively, and the correlation between decolorization and mineralization revealed that a faster decolorization in a Fenton-like process contributed to a higher mineralization rate. This work provides an intrinsic viewpoint of the correlation between Fe-based metallic glasses and dyes in Fenton-like processes and holds the promise to further promote the industrial value of metallic glasses.

Fast Activating Persulfate by Crystallization of Fe-Based Metallic Glasses with External Energy

Very recently, crystallization of metallic glasses (MGs) has presented promising properties in the catalytic field. This work has investigated enhanced catalytic performance of crystallized Fe78Si9B13 ribbons for fast activating persulfate (PS) with assistance of UV-vis light and heat. The ribbons were obtained by annealing at 750°C (Fe-A750) and cibacron brilliant yellow 3G-P (BY 3G-P) dye was used as pollutant. The results indicated that UV-vis light had limited capability to enhance PS activation efficiency by crystallized ribbons while the reaction rate using heat at 65°C was 7.5 times higher than at 25°C, suggesting an advanced performance with heat assistance of Fe-A750 ribbons. Activation energy ∆E for Fe-A750 was measured as 44.5 kJ mol-1. In addition, 5 times reusability could be achieved for Fe-A750 ribbons under 45°C without catalytic decay. The surface morphologies of glassy ribbons, as-annealed Fe-A750 ribbons, HCl-treated Fe-A750 ribbons and after-reused Fe-A750 ribbons have also been systematically studied. This work provides a novel clue to promote applicability of novel crystallized ribbons from MGs.

Pt nanoparticles decorated heterostructured g-C3N4/Bi2MoO6 microplates with highly enhanced photocatalytic activities under visible light

Exploring an efficient and photostable heterostructured photocatalyst is a pivotal scientific topic for worldwide energy and environmental concerns. Herein, we reported that Pt decorated g-C₃N₄/Bi₂MoO₆ heterostructured composites with enhanced photocatalytic performance under visible light were simply synthesized by one-step hydrothermal method for methylene blue (MB) dye degradation. Results revealed that the synthetic Pt decorated g-C₃N₄/Bi₂MoO₆ composites with Bi₂MoO₆ contents of 20 wt.% (Pt@CN/20%BMO) presented the highest photocatalytic activity, exhibiting 7 and 18 times higher reactivity than the pure g-C₃N₄ and Bi₂MoO₆, respectively. Structural analyses showed that Bi₂MoO₆ microplates were anchored on the wrinkled flower-like g-C₃N₄ matrix with Pt decoration, leading to a large expansion of specific surface area from 10.79 m²/g for pure Bi₂MoO₆ to 46.09 m²/g for Pt@CN/20%BMO. In addition, the Pt@CN/20%BMO composites exhibited an improved absorption ability in the visible light region, presenting a promoted photocatalytic MB degradation. Quenching experiments were also conducted to provide solid evidences for the production of hydroxyl radicals (^•OH), electrons (e⁻), holes (h⁺) and superoxide radicals (^•O²⁻) during dye degradation. The findings in this critical work provide insights into the synthesis of heterostructured photocatalysts with the optimization of band gaps, light response and photocatalytic performance in wastewater remediation.

Effect of Ni Addition on Catalytic Performance of Fe87Si5B2P3Nb2Cu1 Amorphous Alloys for Degrading Methylene Blue Dyes

Fe-based amorphous alloys have shown great potential in degrading azo dyes and other organic pollutants. It has been widely investigated as a kind of environmentally friendly material for wastewater remediation. In this paper, we studied the effect of Ni addition on the catalytic performance of Fe87Si5B2P3Nb2Cu1 amorphous alloy for degradation of methylene blue dyes and analyzed the reaction mechanism. (Fe87Si5B2P3Nb2Cu1)86Ni14 amorphous powder with desirable performance was produced by specific ball milling durations. Characterization of the Fe87Si5B2P3Nb2Cu1 and (Fe87Si5B2P3Nb2Cu1)86Ni14 amorphous alloys prepared by ball milling was performed by XRD and SEM. Fe87Si5B2P3Nb2Cu1 and (Fe87Si5B2P3Nb2Cu1)86Ni14 amorphous alloys were used as catalysts to catalyze the degradation of methylene blue dyes, which were detected by UV-VIS near-infrared spectrophotometer. By a series of comparative experiments, it was found that a catalyst dosage of 0.2 g and a reaction temperature of 80 °C were conditions that produced the best catalytic effect. The degradation rate of (Fe87Si5B2P3Nb2Cu1)86Ni14 amorphous alloy to methylene blue dyes prepared by ball milling increased from 67.76% to 99.99% compared with the Fe87Si5B2P3Nb2Cu1 amorphous alloy under the same conditions.

A microwave-activated coal fly ash catalyst for the oxidative elimination of organic pollutants in a Fenton-like process

Raw coal fly ash was first activated by microwave irradiation to promote its catalytic potential and then used as a Fenton-like catalyst to treat polyacrylamide-contaminated wastewater. The optimal activation conditions of the raw coal fly ash (microwave power = 700 W, irradiation time = 10 min, mixing speed = 120 rpm, and raw coal fly ash loading = 20 g L-1) were determined by the orthogonal test. The significance of each effective parameter follows the order: raw coal fly ash loading > microwave power > irradiation time > mixing speed. Microwave irradiation can change the surface morphology and remarkably increase the specific surface area and pore volume. More than 75% of the TOC in the polyacrylamide-contaminated wastewater can be removed under the optimized treatment conditions ([H2O2] = 12 mg L-1, catalyst loading = 10 g L-1, [polyacrylamide] = 200 mg L-1, T = 313 K). The kinetic study shows that the variation in the catalyst loading and the polyacrylamide concentration can change the degradation path of the polyacrylamide, whereas the variation in the H2O2 dosage can accelerate the degradation of polyacrylamide. The Fenton-like process studied herein has a wider optimal pH range (2-5) than that of the classic Fenton process (3). The catalyst has weak catalytic capacity but better catalytic persistence than that of Fe2+. During the five runs of the catalyst, some heavy metallic and toxic elements (Fe, Al, Ti, Cr, Mn, etc.) can be detected but under the limits of the GB8978-1996 standard. Leaching can weaken the catalytic capacity (i.e., stability) of the catalyst. The catalytic process is caused by the synergism of multiple metals and consists of heterogeneous and homogeneous processes.

Research on Lead (II) Adsorption Mechanism from Aqueous Solution by Calcium Carbonate Modified Diatomite Absorbent

In this study, calcium carbonate was used to coat and link the surface of diatomite for the formation of a novel modified adsorbent (referred to as Ca–diatomite). Various analytical techniques were used to characterize structure and mechanisms of modification and adsorption process, like Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD). Results showed that that Calcium carbonate had been successful grafted onto the surface of diatomite after modification, and Calcium carbonate modification improved the adsorption performance of diatomite for the removal of lead (II) ions from aqueous solution. Ca–diatomite adsorption isotherms and adsorption kinetics were also been studied. The adsorption isotherms and the kinetic data were best fitted with the Langmuir model and pseudo-second-order kinetics, respectively.

Heat-Activated Persulfate by Fe-Based Metallic Glass: A Comparative Study of Two Dyes

In this work, the heat-activated persulfate (PS) in the presence of Fe78Si9B13 metallic glasses (MGs) shows an extremely difference in degradation of azo dye and triarylmethane dye, where Fe78Si9B13 MGs exhibits a superior activation ability for PS with assistance of heat leading to the fast removal of two dyes. The structural features of Fe78Si9B13 MGs are firstly characterized by X-ray diffraction (XRD) and differential scanning calorimetry (DSC), following analysis of surface topography by scanning electron microscope (SEM). The results show that with the addition of Fe78Si9B13 MGs, the recalcitrant azo dye is completely removed within 5 min while only 6% of removal rate can be achieved without adding MGs, indicating that the refractory azo dye can be easily degraded by sulfate radical (SO4•–) from heat/MGs/PS. On the other hand, no big variation occurs between PS and MGs/PS under heat activation in degrading triarylmethane dye. Sole PS activated by heat results in a fast removal rate, indicating that triarylmethane dye can be easily degraded by PS itself compared to azo dye. The findings in this work present an in-depth understanding of heat/MGs/PS system in dyes degradation.

Ultra-sustainable Fe78Si9B13 metallic glass as a catalyst for activation of persulfate on methylene blue degradation under UV-Vis light

Stability and reusability are important characteristics of advanced catalysts for wastewater treatment. In this work, for the first time, sulfate radicals (SO4∙-) with a high oxidative potential (Eo = 2.5-3.1 V) were successfully activated from persulfate by a Fe78Si9B13 metallic glass. This alloy exhibited a superior surface stability and reusability while activating persulfate as indicated by it being used for 30 times while maintaining an acceptable methylene blue (MB) degradation rate. The produced SiO2 layer on the ribbon surface expanded strongly from the fresh use to the 20th use, providing stable protection of the buried Fe. MB degradation and kinetic study revealed 100% of the dye degradation with a kinetic rate k = 0.640 within 20 min under rational parameter control. The dominant reactive species for dye molecule decomposition in the first 10 min of the reaction was hydroxyl radicals (∙OH, Eo = 2.7 V) and in the last 10 min was sulfate radicals (SO4∙-), respectively. Empirical operating variables for dye degradation in this work were under catalyst dosage 0.5 g/L, light irradiation 7.7 μW/cm2, and persulfate concentration 1.0 mmol/L. The amorphous Fe78Si9B13 alloy in this work will open a new gate for wastewater remediation.