Electrochemical impedance spectroscopy study of membrane fouling and electrochemical regeneration at a sub-stoichiometric TiO2 reactive electrochemical membrane

Shifting Emphasis from Electro- to Catalytically Active Sites: Effects of Pore Size of Flow-Through Anodes on Water Purification

A flow-through anode has demonstrated high efficiency for micropollutant abatement in water purification. In addition to developing novel electrode materials, a rational design of its porous structure is crucial to achieve high electrooxidation kinetics while sustaining a low cost for flow-through operation. However, our knowledge of the relationship between the pore structure and its performance is still incomplete. Therefore, we systematically explore the effect of pore size (with a median from 4.7 to 49.4 μm) on the flow-through anode efficiency. Results showed that when the pore size was <26.7 μm, the electrooxidation kinetics was insignificantly improved, but the permeability declined dramatically. Traditional empirical evidence from hydrodynamic modeling and electrochemical tests indicated that a flow-through anode with a smaller pore size (e.g., 4.7 μm) had a high mass transfer capability and large electroactive area. However, this did not further accelerate the micropollutant removal. Combining an overpotential distribution model and an imprinting method has revealed that the reactivity of a flow-through anode is related to the catalytically active volume/sites. The rapid overpotential decay as a function of depth in the anode would offset the merits arising from a small pore size. Herein, we demonstrate an optimal pore size distribution (∼20 μm) of typical flow-through anodes to maximize the process performance at a low energy cost, providing insights into the design of advanced flow-through anodes in water purification applications.

Magnéli phase titanium sub-oxides synthesis, fabrication and its application for environmental remediation: Current status and prospect

Sub-stoichiometric titanium oxide, also called titanium suboxides (TSO), had been a focus of research for many decades with a chemical composition of Ti_nO_2n-1 (n ≥ 1). It has a unique oxygen-deficient crystal structure which provides it an outstanding electrical conductivity and high corrosion resistance similar to ceramic materials. High electrical conductivity and ability to sustain in adverse media make these phases a point of attention for researchers in energy storage and environmental remediation applications. The Magnéli phase-based reactive electroconductive membranes (REM) and electrodes have demonstrated the electrochemical oxidation of pollutants in the water in flow-through and flow by configuration. Additionally, it has also shown its potential for visible light photochemical degradation as well. This review attempts to summarize state of the art in various Magnéli phases materials synthesis routes and their electrochemical and photochemical ability for environmental application. The manuscript introduces the Magnéli phase, its crystal structure, and catalytic properties, followed by the recent development in synthesis methods from diverse titanium sources, notably TiO₂ through thermal reduction. The various fabrication methods for Magnéli phase-base REMs and electrodes have also been summarized. Furthermore, the article discussed the environmental remediations via electrochemical and photochemical advanced oxidation processes. Additionally, the hybrid technology with REMs and electrodes is used to counter membrane biofouling and develop electrochemical sensing devices for the pollutants. The Magnéli phase materials have a bright future for both electrochemical and photochemical advanced oxidation of emerging contaminants in water and wastewater treatment.

Membrane Fouling and Electrochemical Regeneration at a PbO2-Reactive Electrochemical Membrane: Study on Experiment and Mechanism

Membrane fouling and regeneration are the key issues for the application of membrane separation (MS) technology. Reactive electrochemical membranes (REMs) exhibited high, stable permeate flux and the function of chemical-free electrochemical regeneration. This study fabricated a micro-filtration REM characterized by a PbO₂ layer (PbO₂-REM) to investigate the electro-triggered anti-fouling and regeneration progress within REMs. The PbO₂-REM exhibited a three-dimensional porous structure with a few branch-like micro-pores. The PbO₂-REM could alleviate Humic acid (HA) and Bisphenol A (BPA) fouling through electrochemical degradation combined with bubble migration, which achieved the best anti-fouling performance at current density of 4 mA cm^-2 with 99.2% BPA removal. Regeneration in the electro-backwash (e-BW) mode was found as eight times that in the forward wash and full flux recovery was achieved at a current density of 3 mA cm^-2. EIS and simulation study also confirmed complete regeneration by e-BW, which was ascribed to the air-water wash formed by bubble migration and flow. Repeated regeneration tests showed that PbO₂-REM was stable for more than five cycles, indicating its high durability for practical uses. Mechanism analysis assisted by finite element simulation illustrated that the high catalytic PbO₂ layer plays an important role in antifouling and regeneration.

A critical review on classifications, characteristics, and applications of electrically conductive membranes for toxic pollutant removal from water: Comparison between composite and inorganic electrically conductive membranes

Research efforts have recently been directed at developing electrically conductive membranes (EMs) for pressure-driven membrane separation processes to remove effectively the highly toxic pollutants from water. EMs serve as both the filter and the electrode during filtration. With the assistance of a power supply, EMs can considerably improve the toxic pollutant removal efficiency and even realize chemical degradation to reduce their toxicity. Organic-inorganic composite EMs and inorganic EMs show remarkable differences in characteristics, removal mechanisms, and application situations. Understanding their differences is highly important to guide the future design of EMs for specific pollutant removal from water. However, reviews concerning the differences between composite and inorganic EMs are still lacking. In this review, we summarize the classifications, fabrication techniques, and characteristics of composite and inorganic EMs. We also elaborate on the removal mechanisms and performances of EMs toward recalcitrant organic pollutants and toxic inorganic ions in water. The comparison between composite and inorganic EMs is emphasized particularly in terms of the membrane characteristics (pore size, permeability, and electrical conductivity), application situations, and underlying removal mechanisms. Finally, the energy consumption and durability of EMs are evaluated, and future perspectives are presented.

Hydroxyl radicals in anodic oxidation systems: generation, identification and quantification

Anodic oxidation has emerged as a promising treatment technology for the removal of a broad range of organic pollutants from wastewaters. Hydroxyl radicals are the primary species generated in anodic oxidation systems to oxidize organics. In this review, the methods of identifying hydroxyl radicals and the existing debates and misunderstandings regarding the validity of experimental results are discussed. Consideration is given to the methods of quantification of hydroxyl radicals in anodic oxidation systems with particular attention to approaches used to compare the electrochemical performance of different anodes. In addition, we describe recent progress in understanding the mechanisms of hydroxyl radical generation at the surface of most commonly used anodes and the utilization of hydroxyl radical in typical electrochemical reactors. This review shows that the key challenges facing anodic oxidation technology are related to i) the elimination of mistakes in identifying hydroxyl radicals, ii) the establishment of an effective hydroxyl radical quantification method, iii) the development of cost effective anode materials with high corrosion resistance and high electrochemical activity and iv) the optimization of electrochemical reactor design to maximise the utilization efficiency of hydroxyl radicals.

Direct electron transfer (DET) processes in a flow anode system-Energy-efficient electrochemical oxidation of phenol

In flow anode systems, surface-bound hydroxyl radicals (*OH) are generated at the solid-liquid interface of suspended particulate charge carriers at potentials well below that required for oxygen evolution as a result of water splitting. While these surface-bound radicals are powerful indiscriminant oxidants that often lead to complete mineralization of organic pollutants, the more selective process of direct electron transfer (DET) may also occur at the particle electrode interfaces and play a critical role in the degradation of some contaminants. In this study, we investigated DET processes in a flow anode system in which carbon black was utilized as the flow anode material and Pt, Ti, IrRu and IrTa meshes were used as the current collectors. The results indicate that the use of a carbon black flow anode enhanced the DET rate by 20 times at 1.0 V vs Ag/AgCl compared to the control experiment with no carbon black particles present. Low solution conductivity had a more obvious negative effect on the DET process (compared to *OH mediated oxidation) due to the high potential drop and inhibition of mass transfer processes at the solid-liquid interfaces of the anode particles. The DET rates were dependent on the particular anode current collector used (i.e., Ti, IrRu, IrTa or Pt mesh) with differences in rates ascribed to the electron transfer resistance of the current collectors in the flow anode system. Detailed investigation of the degradation of phenol in a flow anode system revealed that this widely studied contaminant could be degraded with an energy consumption of 3.08 kWh m^-3, a value substantially lower than that required with other techniques. Results of this study provide a better understanding of the DET mechanism at the solid-solid and solid-liquid interfaces with these insights expected to benefit the design of flow anode materials and current collectors and lead to the improvement in performance of flow anode systems.

Enhanced electrochemical decontamination and water permeation of titanium suboxide reactive electrochemical membrane based on sonoelectrochemistry

Reactive electrochemical membrane (REM) allows electrochemical oxidation (EO) water purification under flow-through operation, which improves mass transfer on the anode surface significantly. However, O₂ evolution reaction (OER) may cause oxygen bubbles to be trapped in small-sized confined flow channels, and thus degrade long-term filterability and treatability of REM. In this study, ultrasound (ultrasonic vibrator, 28 kHz, 180 W) was applied to EO system (i. e. sonoelectrochemistry) containing titanium suboxide-REM (TiSO-REM) anode for enhanced oxidation of 4-chlorophenol (4-CP) target pollutant. Both experimental and modeling results demonstrated that ultrasound could mitigate the retention of O₂ bubbles in the porous structures by destructing large-size bubbles, thus not only increasing permeate flux but also promoting local mass transfer. Meanwhile, oxidation rate of 4-CP for EO with ultrasound (EO-US, 0.0932 min^-1) was 216% higher than that for EO without ultrasound (0.0258 min^-1), due to enhanced mass transfer and OH production under the cavitation effect of ultrasound. Density functional theory (DFT) calculations confirmed the most efficient pathway of 4-CP removal to be direct electron transfer of 4-CP to form [4-CP]⁺, followed by subsequent oxidation mediated by OH produced from anodic water oxidation on TiSO-REM anode. Last, the stability of TiSO-REM could be improved considerably by application of ultrasound, due to alleviation of electrode deactivation and fouling, indicated by cyclic test, scan electron microscopy (SEM) observation and Fourier transform infrared spectroscopy (FT-IR) characterization. This study provides a proof-of-concept demonstration of ultrasound for enhanced EO of recalcitrant organic pollutants by REM anode, making decentralized wastewater treatment more efficient and more reliable.

Facing the Challenge of Poly- and Perfluoroalkyl Substances in Water: Is Electrochemical Oxidation the Answer?

Electrochemical treatment systems have the unique ability to completely mineralize poly- and perfluoroalkyl substances (PFASs) through potential-driven electron transfer reactions. In this review, we discuss the state-of-the-art on electrooxidation of PFASs in water, aiming at elucidating the impact of different operational and design parameters, as well as reported mechanisms of PFAS degradation at the anode surface. We have identified several shortcomings of the existing studies that are largely limited to small-scale laboratory batch systems and unrealistic synthetic solutions, which makes extrapolation of the obtained data to real-world applications difficult. PFASs are surfactant molecules, which display significant concentration-dependence on adsorption, electrosorption, and dissociation. Electrooxidation experiments conducted with high initial PFAS concentration and/or in high conductivity supporting electrolytes likely overestimate process performance. In addition, the formation of organohalogen byproducts, chlorate and perchlorate, was seldom considered. Nevertheless, the first step toward advancing from laboratory-scale to industrial-scale applications is recognizing both the strengths and limitations of electrochemical water treatment systems. More comprehensive and rigorous evaluation of novel electrode materials, application of scalable proof-of-concept studies, and acknowledgment of all treatment outputs (not just the positive ones) are imperative. The presence of PFASs in drinking water and in the environment is an urgent global public health issue. Developments made in material science and application of novel three-dimensional, porous electrode materials and nanostructured coatings are forging a path toward more sustainable water treatment technologies and potential chemical-free treatment of PFAS-contaminated water.

Membrane Separation Coupled with Electrochemical Advanced Oxidation Processes for Organic Wastewater Treatment: A Short Review

Research on the coupling of membrane separation (MS) and electrochemical advanced oxidation processes (EAOPs) has been a hot area in water pollution control for decades. This coupling aims to greatly improve water quality and focuses on the challenges in practical application to provide a promising solution to water shortage problems. This article provides a summary of the coupling configurations of MS and EAOPs, including two-stage and one-pot processes. The two-stage process is a combination of MS and EAOPs where one process acts as a pretreatment for the other. Membrane fouling is reduced when setting EAOPs before MS, while mass transfer is promoted when placing EAOPs after MS. A one-pot process is a kind of integration of two technologies. The anode or cathode of the EAOPs is fabricated from porous materials to function as a membrane electrode; thus, pollutants are concurrently separated and degraded. The advantages of enhanced mass transfer and the enlarged electroactive area suggest that this process has excellent performance at a low current input, leading to much lower energy consumption. The reported conclusions illustrate that the coupling of MS and EAOPs is highly applicable and may be widely employed in wastewater treatment in the future.

A Composite Membrane Based on Sulfonated Polystyrene Implanted in a Stretched PTFE Film for Vanadium Flow Batteries

The quality of ion-selective membranes determines the efficiency of Vanadium Flow Batteries (VFBs), and alternatives to expensive Nafion™ materials are actively being searched for. One of the membrane architecture approaches is to imitate the Nafion™ structure with two separate phases: a conductive sulfonated polymer and an inner matrix. We introduce a new composite material based on sulfonated styrene polymerized inside the pores of a stretched PTFE matrix. Variation of polystyrene content and a sulfonation degree allowed to obtain membranes with IEC from to 0.96 to 1.84 mmol/g. Balanced vanadium permeability (ca. 5.5 ⋅ 10^-6  cm² /min) and proton conductivity (ca. 50 mS/cm) were achieved for the material with 21-23 % polystyrene content and a sulfonation degree up to 94 %. Membranes showed stable cycling with 81 % energy efficiency in a single-cell VFB. This work contributes to the existing knowledge of Nafion alternatives by providing a cheap and scalable method of membrane production.

Microalgae Filtration Using an Electrochemically Reactive Ceramic Membrane: Filtration Performances, Fouling Kinetics, and Foulant Layer Characteristics

Electrochemical membrane filtration has proven to be successful for microbial removal and separation from water. In addition, membrane fouling could be mitigated by electrochemical reactions and electrostatic repulsion on a reactive membrane surface. This study assessed the filtration performances and fouling characteristics of electrochemically reactive ceramic membranes (a Magneli phase suboxide of TiO₂) when filtering algal suspension under different dc currents to achieve anodic or cathodic polarization. The critical flux results indicate that when applying positive or negative dc currents (e.g., 1.25-2.5 mA·cm^-2) to the membrane, both significantly mitigated membrane fouling and thus maintained higher critical fluxes (up to 14.6 × 10^-5·m³·m^-2·s^-1 or 526 LMH) compared to the critical flux without dc currents. Moreover, applying dc currents also enhanced membrane defouling processes and recovered high permeate flux better than hydraulic and chemical backwash methods. Moreover, fouling kinetics and the cake layer formation were further analyzed with a resistance-in-series model that revealed many important but underexamined parameters (e.g., cake layer resistance and cake layer thickness). The cake layer structures (e.g., compressibility) were shown to vary with the electrochemical activity, which provide new insight into the biofouling mechanisms. Finally, the algogenic odor, geosmin, was shown to be effectively removed by this reactive membrane under positive dc currents (2.5 mA·cm^-2), which highlights the multifunctional capabilities of electrochemically reactive membrane filtration in biomass separation, fouling prevention, and pollutant degradation.

Solid-phase fluorescence excitation emission matrix for in-situ monitoring of membrane fouling during microfiltration using a polyvinylidene fluoride hollow fiber membrane

Controlling membrane fouling is challenging and information regarding the causes of fouling is critical for this. While liquid-phase fluorescence spectroscopy excitation emission matrix (LPF-EEM) has previously been applied to identify the characteristics of membrane foulants, we applied EEM measurements to solid samples to identify foulants accumulated on the membrane. This solid-phase fluorescence EEM (SPF-EEM) enables sensitive and nondestructive identification of different organic solids. LPF-EEMs and SPF-EEMs were used on natural organic matter (NOM) isolated from secondary-treated wastewater, which revealed differences in peak positions and in spectral shapes. SPF-EEMs and LPF-EEMs of hydrophobic (HPO), transphilic (TPI) and hydrophilic (HPI) fractions showed that peaks of HPO fraction disappeared while those of TPI and HPI fractions shifted to a longer excitation and emission position through solidification. Then, the surface of the membrane fiber was continuously monitored using SPF-EEM during filtration. Three peaks appeared as expected during membrane fouling progression, indicating that in-situ monitoring of foulants was successful. Comparison of the EEM peaks between foulants and isolated NOM fractions shows the presence of both liquid-phase proteinaceous substances and gels formed from HPI and TPI fractions. Changes in peak intensity confirmed that the former proteinaceous substances were responsible for both reversible and irreversible fouling, while the latter gels mainly contributed to the irreversible fouling. We demonstrated the functionality of the SPF-EEM as an in-situ fouling monitoring tool.

Electro-Driven in Situ Construction of Functional Layer Using Amphoteric Molecule: The Role of Tryptophan in Ion Sieving

The permselective separation of monovalent ions from the solution with the coexistence of multivalent ions was required in the industry of the wastewater treatment and resource recycling. Here, in this work, a novel electro-driven in situ modification method was utilized in the positively charged tryptophan solution to prepare highly permselective cation exchange membrane (CEM). We have optimized the process conditions and discussed the modification mechanism by drawing upon the fouling phenomenon in the membrane separation processes. A series of conventional characterization methods such as scanning electron microscopy (SEM), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and electrochemical impedance spectroscopy (EIS) were used to investigate the structure and performance changes after the modification. The SEM-energy-dispersive X-ray (SEM-EDX) was introduced for analyzing the transfer of Na+ and Mg2+ in the functional modification layer and the membrane matrix, thus illustrating the sieving mechanism for the modified membranes. The resultant membranes were observed to have the changed interstructure and the multivalent-ion-repulsive modification layer. Due to the channel filling and electrostatic repulsion effect, the electro-driven tryptophan endowed the pristine CMX with superior monovalent cation permselectivity (PMg2+Na+: 6-35), which was higher than that of pristine CMX and the commercial Neosepta CIMS. It confirms that the proposed electro-driven tryptophan in situ modification method could effectively help improve the membrane permselectivity by structurally forming stable crystallization on and within the membrane, which provides a feasible choice for the cation exchange membrane modification.

Differential ATR FTIR spectroscopy of membrane fouling: Contributions of the substrate/fouling films and correlations with transmembrane pressure

This study examined the formation of fouling films deposited on the surface of a polyethersulfone (PES) membrane during the filtration of alginate solutions with various ionic strengths. Membrane fouling was characterized by changes of the transmembrane pressure (TMP) and ex situ measured attenuated total reflectance (ATR) Fourier-transform IR (FTIR) spectra at varying stages of filtration runs. The ATR spectra that comprise the vibration bands characteristic of the PES substrate and the deposited film were processed taking into the gradual weakening of the PES substrate-specific bands, whose intensity was shown to depend on the wavenumber of IR radiation and the thickness of the deposited layer. Strongly linear correlations between ratios of first derivatives intensity and wavenumbers of the PES reference lines were established. Calculations of the PES bands' attenuation coefficients allowed determining the apparent thickness and ATR FTIR vibrations of the fouling films per se. Strong correlations between TMP development and ATR-determined apparent thickness of the fouling layers were observed. The intensity of ATR absorbance at 3200 cm^-1 was linearly correlated with TMP development for small TMP values before the point of rapidly developing failure of the hydraulic permeability of the system was reached.

Electroactive Membranes for Water Treatment: Enhanced Treatment Functionalities, Energy Considerations, and Future Challenges

To meet the increasing demand for water, potable water providers are turning toward unconventional waters, such as seawater and wastewater. These highly saline and/or heavily contaminated water sources are difficult to treat, demanding the use of advanced technology not typically used to treat conventional water sources such as river water or fresh groundwater. Of these advanced technologies, membrane separation processes are fast becoming the most widely used methods to convert these marginal waters into useful resources. The main factors contributing to the widespread adoption of membrane separation processes for water treatment include their modular nature, small physical footprint, and relative energy efficiency compared to traditional distillation processes. In addition, membranes present a physical barrier to pathogens, which is an attractive feature in terms of disinfection credits. However, traditional membrane materials suffer from several distinct drawbacks, which include membrane fouling (the accumulation of material on the membrane surface that blocks the flow of water), the need for high-pressure membranes (such as reverse osmosis (RO) or nanofiltration (NF)) or membrane/thermal processes (e.g., membrane distillation (MD)) to remove small contaminant compounds (e.g., trace metals, salt, endocrine disrupting compounds), and a pressure-driven membrane's inability to effectively remove small, uncharged molecules (e.g., N-nitrosodimethylamine (NDMA), phenol, acetone, and boron). Electrically driven physical and chemical phenomena, such as electrophoresis, electrostatic repulsion, dielectrophoresis, and electricity-driven redox reactions, have long been coupled to membrane-based separation processes, in a process known as electrofiltration. However, it is only in recent years that appropriate membrane materials (i.e., electrically conducting membranes (EMs)) have been developed that enable the efficient use of these electro-driven processes. Specifically, the development of EM materials (both polymeric and inorganic) have reduced the energy consumption of electrofiltration by using the membrane as an electrode in an electrochemical circuit. In essence, a membrane-electrode allows for the concentrated delivery of electrical energy directly to the membrane/water interface where the actual separation process takes place. In the past, metal electrodes were placed on either side of the membrane, which resulted in large potentials needed to drive electrochemical/electrokinetic phenomena. The use of a membrane-electrode dramatically reduces the required potentials, which reduces energy consumption and can also eliminate electrocorrosion and the formation of undesirable byproducts. In this Account, we review recent developments in the field of electrofiltration, with a focus on two water treatment applications: desalination and water reuse (wastewater or contaminated groundwater recycling). Specifically, we discuss how EMs can be used to minimize multiple forms of fouling (biofouling, mineral scaling, organic fouling); how electrochemical reactions at the membrane/water interface are used to destroy toxic contaminants, clean a membrane surface, and transform the local pH environment, which enhances the rejection of certain contaminants; how electric fields and electrostatic forces can be used to reorient molecules at the membrane/water interface; and how electrical energy can be transformed into thermal energy to drive separation processes. A special emphasis is placed on explicitly defining the additional energy consumption associated with the electrochemical phenomena, as well as the additional cost associated with fabricating EM materials. In addition, we will discuss current limitations of the electrofiltration process, with particular attention given to the current limitations of membrane materials and the future research needs in the area of membrane materials and module development.

Electro-oxidation of organic pollutants by reactive electrochemical membranes

Electro-oxidation processes are promising options for the removal of organic pollutants from water. The major appeal of these technologies is the possibility to avoid the addition of chemical reagents. However, a major limitation is associated with slow mass transfer that reduces the efficiency and hinders the potential for large-scale application of these technologies. Therefore, improving the reactor configuration is currently one of the most important areas for research and development. The recent development of a reactive electrochemical membrane (REM) as a flow-through electrode has proven to be a breakthrough innovation, leading to both high electrochemically active surface area and convection-enhanced mass transport of pollutants. This review summarizes the current state of the art on REMs for the electro-oxidation of organic compounds by anodic oxidation. Specific focuses on the electroactive surface area, mass transport, reactivity, fouling and stability of REMs are included. Recent advances in the development of sub-stoichiometric titanium oxide REMs as anodes have been made. These electrodes possess high electrical conductivity, reactivity (generation of ^•OH), chemical/electrochemical stability, and suitable pore structure that allows for efficient mass transport. Further development of REMs strongly relies on the development of materials with suitable physico-chemical characteristics that produce electrodes with efficient mass transport properties, high electroactive surface area, high reactivity and long-term stability.

Mineralization of organic pollutants by anodic oxidation using reactive electrochemical membrane synthesized from carbothermal reduction of TiO2

Reactive Electrochemical Membrane (REM) prepared from carbothermal reduction of TiO₂ is used for the mineralization of biorefractory pollutants during filtration operation. The mixture of Ti₄O₇ and Ti₅O₉ Magnéli phases ensures the high reactivity of the membrane for organic compound oxidation through ^•OH mediated oxidation and direct electron transfer. In cross-flow filtration mode, convection-enhanced mass transport of pollutants can be achieved from the high membrane permeability (3300 LMH bar^-1). Mineralization efficiency of oxalic acid, paracetamol and phenol was assessed as regards to current density, transmembrane pressure and feed concentration. Unprecedented high removal rates of total organic carbon and mineralization current efficiency were achieved after a single passage through the REM, e.g. 47 g m^-2 h^-1 - 72% and 6.7 g m^-2 h^-1 - 47% for oxalic acid and paracetamol, respectively, at 15 mA cm^-2. However, two mechanisms have to be considered for optimization of the process. When the TOC flux is too high with respect to the current density, aromatic compounds polymerize in the REM layer where only direct electron transfer occurs. This phenomenon decreases the oxidation efficiency and/or increases REM fouling. Besides, O₂ bubbles sweeping at high permeate flux promotes O₂ gas generation, with adverse effect on oxidation efficiency.

A review of reverse osmosis membrane fouling and control strategies

Reverse osmosis (RO) membrane technology is one of the most important technologies for water treatment. However, membrane fouling is an inevitable issue. Membrane fouling leads to higher operating pressure, flux decline, frequent chemical cleaning and shorter membrane life. This paper reviews membrane fouling types and fouling control strategies, with a focus on the latest developments. The fundamentals of fouling are discussed in detail, including biofouling, organic fouling, inorganic scaling and colloidal fouling. Furthermore, fouling mitigation technologies are also discussed comprehensively. Pretreatment is widely used in practice to reduce the burden for the following RO operation while real time monitoring of RO has the advantage and potential of providing support for effective and efficient cleaning. Surface modification could slow down membrane fouling by changing surface properties such as surface smoothness and hydrophilicity, while novel membrane materials and synthesis processes build a promising future for the next generation of RO membranes with big advancements in fouling resistance. Especially in this review paper, statistical analysis is conducted where appropriate to reveal the research interests in RO fouling and control.