3D printed spacers based on TPMS architectures for scaling control in membrane distillation

Carbon-Based Nanocomposite Membranes for Membrane Distillation: Progress, Problems and Future Prospects

The development of an ideal membrane for membrane distillation (MD) is of the utmost importance. Enhancing the efficiency of MD by adding nanoparticles to or onto a membrane's surface has drawn considerable attention from the scientific community. It is crucial to thoroughly examine state-of-the-art nanomaterials-enabled MD membranes with desirable properties, as they greatly enhance the efficiency and reliability of the MD process. This, in turn, opens up opportunities for achieving a sustainable water-energy-environment nexus. By introducing carbon-based nanomaterials into the membrane's structure, the membrane gains excellent separation abilities, resistance to various feed waters, and a longer lifespan. Additionally, the use of carbon-based nanomaterials in MD has led to improved membrane performance characteristics such as increased permeability and a reduced fouling propensity. These nanomaterials have also enabled novel membrane capabilities like in situ foulant degradation and localized heat generation. Therefore, this review offers an overview of how the utilization of different carbon-based nanomaterials in membrane synthesis impacts the membrane characteristics, particularly the liquid entry pressure (LEP), hydrophobicity, porosity, and membrane permeability, as well as reduced fouling, thereby advancing the MD technology for water treatment processes. Furthermore, this review also discusses the development, challenges, and research opportunities that arise from these findings.

Mineral scaling induced membrane wetting in membrane distillation for water treatment: Fundamental mechanism and mitigation strategies

The scaling-induced wetting phenomenon seriously affects the application of membrane distillation (MD) technology in hypersaline wastewater treatment. Unlike the large amount of researches on membrane scaling and membrane wetting, scaling-induced wetting is not sufficiently studied. In this work, the current research evolvement of scaling-induced wetting in MD was systematically summarized. Firstly, the theories involving scaling-induced wetting were discussed, including evaluation of scaling potential of specific solutions, classical and non-classical crystal nucleation and growth theories, observation and evolution of scaling-induced processes. Secondly, the primary pretreatment methods for alleviating scaling-induced wetting were discussed in detail, focusing on adding agents composed of coagulation, precipitation, oxidation, adsorption and scale inhibitors, filtration including granular filtration, membrane filtration and mesh filtration and application of external fields including sound, light, heat, electromagnetism, magnetism and aeration. Then, the roles of operation conditions and cleaning conditions in alleviating scaling-induced wetting were evaluated. The main operation parameters included temperature, flow rate, pressure, ultrasound, vibration and aeration, while different types of cleaning reagents, cleaning frequency and a series of assisted cleaning measures were summarized. Finally, the challenges and future needs in the application of nucleation theory to scaling-induced wetting, the speculation, monitoring and mitigation of scaling-induced wetting were proposed.

Evaluation of vibratory shear-enhanced processing module-integrated three-dimensional printed spacers for enhanced wastewater ultrafiltration

The article evaluates the effectiveness of two new designed module-integrated three-dimensional (3D) printed spacers in enhancing wastewater ultrafiltration efficiencies using vibratory shear-enhanced processing (VSEP). The study investigates the star-shaped spacer filled module channel (star spacer) and the column-shaped herringbone spacer filled module channel with the same position as the flow direction (column spacer) and with the opposite position as the flow direction (rev column spacer). It compares the VSEP module-integrated spacers with membrane module vibration (module vibration) and empty membrane module channel (control) configurations. The results show that the module integration of the 3D printed spacers can greatly improve the specific, average, and constant permeate fluxes and can contribute to reducing the total, reversible and irreversible resistance values, and specific energy consumption of the ultrafiltration membrane separation experiments. Overall, this study provides valuable insights into improving the performance of wastewater ultrafiltration systems and fouling mitigation through the module integration of 3D printed spacers and membrane module vibration. PRACTITIONER POINTS: Vibratory shear-enhanced processing (VSEP) ultrafiltration module-integrated 3D printed spacers were successfully fabricated and evaluated for improved wastewater treatment. Two spacer designs, a star-shaped and a column-shaped herringbone, were compared with an empty membrane module channel with and without vibration. Two configurations of the column-shaped spacer, in the same and reversed flow direction, were tested. Specific energy consumption was calculated and compared for all configurations. Significant improvements in ultrafiltration performance were observed with the use of spacers compared with an empty module channel, including enhanced permeate fluxes and reductions in both total and reversible, as well as irreversible, resistance.

Photothermal Surface Heating Membrane Distillation Using 3D-Printed Ti3C2Tx MXene-Based Nanocomposite Spacers

To address the growing global need for freshwater, it has become essential to use nonpotable saline water. Solar membrane distillation is a potential desalination method that does not need conventional electricity and may cut water production costs. In this study, we develop a photothermal surface heating membrane distillation using a new class of photothermal spacers constructed with Ti₃C₂T_x MXene-based nanocomposites. In contrast to traditional membrane distillation, which utilizes energy-intensive bulk feed heating, solar-powered surface heating membrane distillation removes the external thermal energy input requirements, hence reducing operating costs significantly. In particular, three-dimensional (3D)-printing technology was used to fabricate the functional spacer, which allowed the design and materials to be fine-tuned per the needs of the process. Under solar illumination, the printed spacer can exhibit a localized photothermal conversion-driven heating effect near the surface of distillation membranes, which generates vapor pressure strong enough to operate distillation across membranes. Importantly, a two-dimensional Ti₃C₂T_x MXene with outstanding photothermal conversion efficiency and stability in hypersaline ionic solutions was incorporated into the 3D-printed spacers as the crucial nanofiller for imparting a local heating effect of feed. The fabricated nanocomposite spacers showed superior photothermal heating response under sunlight with an average permeate flux and energy conversion efficiency of 0.49 kg·m^-2·h^-1 and 30.6%, respectively. An enhancement in both photothermal efficiency and permeate flux was noticed as the amount of MXene nanosheets increased in the 3D-printed spacers. This study demonstrates the feasibility of using 3D-printed photothermal spacers for high-performance and sustainable surface heating membrane distillation, providing a promising avenue for further improvement with other photothermal nanofillers or spacer modifications.

Engineered multi-scale roughness of carbon nanofiller-embedded 3D printed spacers for membrane distillation

Membrane distillation (MD) transfers heat and mass simultaneously through a hydrophobic membrane. Hence, it is sensitive to both concentration and temperature polarisation (CP and TP) effects. In this study, we fabricated feed spacers to improve MD efficiency by alleviating the polarisation effects. First, a 3D printed spacer design was optimised to show superior performance amongst the others tested. Then, to further enhance spacer performance, we incorporated highly thermally stable carbon nanofillers, including carbon nanotubes (CNT) and graphene, in the fabrication of filaments for 3D printing. All the fabricated spacers had a degree of engineered multi-scale roughness, which was relatively high compared to that of the polylactic acid (PLA) spacer (control). The use of nanomaterial-incorporated spacers increased the mean permeate flux significantly compared to the PLA spacer (27.1 L/m²h (LMH)): a 43% and 75% increase when using the 1% graphene-incorporated spacer (38.9 LMH) and 2% CNT incorporated spacer (47.5 LMH), respectively. This could be attributed to the locally enhanced turbulence owing to the multi-scale roughness formed on the spacer, which further increased the vaporisation rate through the membrane. Interestingly, only the CNT-embedded spacer markedly reduced the ion permeation through the membrane, which may be due to the effective reduction of CP. This further decreased with increasing CNT concentration, confirming that the CNT spacer can simultaneously reduce the CP and TP effects in the MD process. Finally, we successfully proved that the multi-scale roughness of the spacer surface induces micromixing near the membrane walls, which can improve the MD performance via computational fluid dynamics.

Negative Pressure Membrane Distillation for Excellent Gypsum Scaling Resistance and Flux Enhancement

Membrane distillation (MD) has potential to become a competitive technology for managing hypersaline brine but not until the critical challenge of mineral scaling is addressed. The state-of-the-art approach for mitigating mineral scaling in MD involves the use of superhydrophobic membranes that are difficult to fabricate and are commercially unavailable. This study explores a novel operational strategy, namely, negative pressure direct contact membrane distillation (NP-DCMD) that can minimize mineral scaling with commercially available hydrophobic membranes and at the same time enhance the water vapor flux substantially. By applying a negative gauge pressure on the feed stream, NP-DCMD achieved prolonged resistance to CaSO₄ scaling and a dramatic vapor flux enhancement up to 62%. The exceptional scaling resistance is attributable to the formation of a concave liquid-gas under a negative pressure that changes the position of the water-air interface to hinder interfacial nucleation and crystal growth. The substantial flux enhancement is caused by the reduced molecular diffusion resistance within the pores and the enhanced heat transfer kinetics across the boundary layer in NP-DCMD. Achieving substantial performance improvement in both the scaling resistance and vapor flux with commercial membranes, NP-DCMD is a significant innovation with vast potential for practical adoption due to its simplicity and effectiveness.

Fouling mitigation in reverse osmosis processes with 3D printed sinusoidal spacers

Feed spacers are an essential part of spiral wound modules for reverse osmosis (RO). They create flow channels between membrane sheets and manipulate hydrodynamic conditions to control membrane fouling. In this work, additive manufacturing (Polyjet) was used to print novel sinusoidal spacers with wavy axial filaments connected by perpendicular (ST) or slanted (SL) transverse filaments. When tested with 2 g/L NaCl solution, conventional and SL spacers had similar flux while the ST spacer had about 5-7% lower flux. The pressure losses for ST and SL spacers increased by up to 3 folds depending on the flow condition. In the colloidal silica fouling and biofouling tests, the sinusoidal spacers showed lower membrane permeability decrease of 46% for ST, 41% for SL vs 56% for conventional and 26% for ST, 22% for SL vs 33% for conventional, respectively. Optical coherence tomography images from colloidal silica fouling and confocal images from biofouling tests revealed that fouling patterns were closely associated with the local hydrodynamic conditions. Overall, sinusoidal spacers showed promising results in controlling membrane fouling, but there is potential for further optimizations to reduce channel pressure loss.

Programmed Plastic Deformation in Mathematically-Designed Architected Cellular Materials

The ability to control the exhibited plastic deformation behavior of cellular materials under certain loading conditions can be harnessed to design more reliable and structurally efficient damage-tolerant materials for crashworthiness and protective equipment applications. In this work, a mathematically-based design approach is proposed to program the deformation behavior of cellular materials with minimal surface-based topologies and ductile constituent material by employing the concept of functional grading to control the local relative density of unit cells. To demonstrate the applicability of this design tactic, two examples are presented. Rhombic, and double arrow deformation profiles were programmed as the desired deformation patterns. Grayscale images were used to map the relative density distribution of the cellular material. 316L stainless steel metallic samples were fabricated using the powder bed fusion additive manufacturing technique. Results of compressive tests showed that the designed materials followed the desired programmed deformation behavior. Results of mechanical testing also showed that samples with programmed deformation exhibited higher plateau stress and toughness values as compared to their uniform counterparts while no effect on Young’s modulus was observed. Plateau stress values increased by 8.6% and 13.4% and toughness values increased by 5.6% and 11.2% for the graded-rhombic and graded-arrow patterns, respectively. Results of numerical simulations predicted the exact deformation behavior that was programmed in the samples and that were obtained experimentally.

The emerging role of 3D printing in water desalination

Unmatched flexibility in terms of material selection, design and scalability, along with gradually decreasing cost, has led 3D printing to gain significant attention in various water treatment and desalination applications. In desalination, 3D printing has been applied to improve the energy efficiency of existing technologies. For thermal desalination, this involves the use of 3D printed components that enhance water evaporation and energy harvesting with new materials and designs. For membrane-based desalination, 3D printing offers membranes and other module components with customized materials and geometries for better fouling resistance and productivity. This review highlights the current status, advances and challenges associated with 3D printing in both thermal and membrane-based desalination technologies. Other unique benefits offered by 3D printing for water desalination along with the associated challenges are also discussed in this review. Finally, the future prospects and research directions are highlighted related to the application of 3D printing in the water desalination industry.

Design procedure for triply periodic minimal surface based biomimetic scaffolds

Cellular additively manufactured metallic structures for load-bearing scaffolds in the context of bone tissue engineering (BTE) have emerged as promising candidates. Due to many advantages in terms of morphology, stiffness, strength and permeability compared to conventional truss structures, lattices based on triply periodic minimal surfaces (TPMS) have recently attracted increasing interest for this purpose. In addition, the finite element method (FEM) has been proven to be suitable for accurately predicting the deformation behavior as well as the mechanical properties of geometric structures after appropriate parameter validation based on experimental data. Numerous publications have examined many individual aspects, but conceptual design procedures that consider at least the essential requirements for cortical and trabecular bone simultaneously are still rare. Therefore, this paper presents a numerical approach to first determine the actual admissible design spaces for a choice of TPMS based lattices with respect to key parameters and then weight them with respect to further benefit parameters. The admissible design spaces are limited by pore size, strut size and volume fraction, and the subsequent weighting is based on Young's modulus, cell size and surface area. Additively manufactured beta-Ti-42Nb with a strain stiffness of 60.5GPa is assumed as material. In total, the procedure considers twelve lattice types, consisting of six different TPMS, each as network solid and as sheet solid. The method is used for concrete prediction of suitable TPMS based lattices for cortical bone and trabecular bone. For cortical bone a lattice based on the Schwarz Primitive sheet solid with 67.572μm pore size, 0.5445 volume fraction and 18.758GPa Young's modulus shows to be the best choice. For trabecular bone a lattice based on the Schoen Gyroid network solid with 401.39μm pore size, 0.3 volume fraction and 4.6835GPa Young's modulus is the identified lattice. Finally, a model for a long bone scaffold is generated from these two lattices using functional grading methods in terms of volume fraction, cell size and TPMS type. In particular, the presented procedure allows an efficient estimation for a likely suitable biometric TPMS-based scaffolds. In addition to medical applications, however, the method can also be transferred to numerous other applications in mechanical, civil and electrical engineering.

Roles and performance enhancement of feed spacer in spiral wound membrane modules for water treatment: A 20-year review on research evolvement

Membrane technologies have been widely applied in water treatment, wastewater reclamation and seawater desalination. Feed spacer present in spiral wound membrane (SWM) modules plays a pivotal role in creating flow channels, promoting fluid mixing and enhancing mass transfer. However, it induces the increase of feed channel pressure (FCP) drop and localized stagnant zones that provokes membrane fouling. For the first time, we comprehensively review the research evolvement on feed spacer in SWM modules for water treatment over the last 20 years, to reveal the impacts of feed spacer on the hydrodynamics and biofouling in the spacer-filled channel, and to discuss the potential approaches and current limitations for the modification of feed spacer. The research process can be divided into three phases, with research focus shifting from hydrodynamics in Phase Ⅰ (the year of 2001-2008), to biofouling in Phase Ⅱ (the year of 2009-2015), and then to novel spacer designs in Phase Ⅲ (the year of 2016-2020). The spacer configuration has a momentous impact on the hydraulic performance regarding flow velocity field, shear stress, mass transfer and FCP drop. Biofouling initially occurs on feed spacer, especially around spacer filaments and the contact zones with membrane surface, and ultimately degrades the overall membrane performance indicating the importance of controlling spacer biofouling. The modification of feed spacer is mainly achieved by altering surface chemistry or introducing novel configurations. However, the stability of spacer coating and the economy and practicality of 3D-printed spacer remain a predicament to be tackled. Future studies are suggested to focus on the standardization of testing conditions for spacer evaluation, the effect of hydrodynamics on membrane fouling control, the design and fabrication of novel feed spacer adaptable for SWM modules, the application of feed spacer for drinking water production, organic fouling control in spacer-filled channel and the role of permeate spacer on membrane performance.

A Critical Review of Membrane Wettability in Membrane Distillation from the Perspective of Interfacial Interactions

Hydrophobic membranes used in membrane distillation (MD) systems are often subject to wetting during long-term operation. Thus, it is of great importance to fully understand factors that influence the wettability of hydrophobic membranes and their impact on the overall separation efficiency that can be achieved in MD systems. This Critical Review summarizes both fundamental and applied aspects of membrane wetting with particular emphasis on interfacial interaction between the membrane and solutes in the feed solution. First, the theoretical background of surface wetting, including the relationship between wettability and interfacial interaction, definition and measurement of contact angle, surface tension, surface free energy, adhesion force, and liquid entry pressure, is described. Second, the nature of wettability, membrane wetting mechanisms, influence of membrane properties, feed characteristics and operating conditions on membrane wetting, and evolution of membrane wetting are reviewed in the context of an MD process. Third, specific membrane features that increase resistance to wetting (e.g., superhydrophobic, omniphobic, and Janus membranes) are discussed briefly followed by the comparison of various cleaning approaches to restore membrane hydrophobicity. Finally, challenges with the prevention of membrane wetting are summarized, and future work is proposed to improve the use of MD technology in a variety of applications.

Antiscaling 3D printed feed spacers via facile nanoparticle coating for membrane distillation

Surface modification of feed spacers rather than membranes may hold more merit as an antiscaling strategy in membrane distillation (MD), as it avoids compromising the functionality of MD membrane. In this work, an antiscaling polyamide 3D printed spacer was developed for MD. The surface of the printed spacer was coated with fluorinated silica (FS) nanoparticles synthesized via a sol-gel process. The sol-gel approach used to synthesize the FS nanoparticles is considered a convenient and easy approach for engineering the spacer's surface structure and roughness. The performance of the FS coated printed surface was evaluated against other coating materials of different chemical properties. The coated surfaces were characterized using water contact angle measurements, ATR-FTIR, Raman, FESEM-EDX, atomic force and 3D microscopes. The 3D printed surface's microscale roughness and hydrophobicity increased, while its surface-free energy decreased with FS nanoparticles coating. The antiscaling performance of uncoated and FS coated spacers was then assessed in a direct contact MD process, using a scale-inducing aqueous solution of calcium sulfate as its feed. The scalant (Ca²⁺) attachment on the FS coated spacer was 0.24 mg cm^-2, 74% lower than on the uncoated 3D spacer (0.95 mg cm^-2). Also, by using the antiscaling FS coated spacer, scaling on the membrane surface dropped by 60%. The predominant factors that helped minimize scaling with FS coating were microscale roughness-induced hydrophobicity and reduced surface-free energy that weakened the scalant 's interaction with the spacer surface.

A review on spacers and membranes: Conventional or hybrid additive manufacturing?

Over the past decade, 3D printing or additive manufacturing (AM) technology has seen great advancement in many aspects such as printing resolution, speed and cost. Membranes for water treatment experienced significant breakthroughs owing to the unique benefits of additive manufacturing. In particular, 3D printing's high degree of freedom in various aspects such as material and prototype design has helped to fabricate innovative spacers and membranes. However, there were conflicting reports on the feasibility of 3D printing, especially for membranes. Some research groups stated that technology limitations today made it impossible to 3D print membranes, but others showed that it was possible by successfully fabricating prototypes. This paper will provide a critical and comprehensive discussion on 3D printing specifically for spacers and membranes. Various 3D printing techniques will be introduced, and their suitability for membrane and spacer fabrication will be discussed. It will be followed by a review of past studies associated with 3D-printed spacers and membranes. A new category of additive manufacturing in the membrane water industry will be introduced here, known as hybrid additive manufacturing, to address the controversies of 3D printing for membrane. As AM technology continues to advance, its possibilities in the water treatment is limitless. Some insightful future trends will be provided at the end of the paper.

A Review of CFD Modelling and Performance Metrics for Osmotic Membrane Processes

Simulation via Computational Fluid Dynamics (CFD) offers a convenient way for visualising hydrodynamics and mass transport in spacer-filled membrane channels, facilitating further developments in spiral wound membrane (SWM) modules for desalination processes. This paper provides a review on the use of CFD modelling for the development of novel spacers used in the SWM modules for three types of osmotic membrane processes: reverse osmosis (RO), forward osmosis (FO) and pressure retarded osmosis (PRO). Currently, the modelling of mass transfer and fouling for complex spacer geometries is still limited. Compared with RO, CFD modelling for PRO is very rare owing to the relative infancy of this osmotically driven membrane process. Despite the rising popularity of multi-scale modelling of osmotic membrane processes, CFD can only be used for predicting process performance in the absence of fouling. This paper also reviews the most common metrics used for evaluating membrane module performance at the small and large scales.

Design and Characterization of Sheet-Based Gyroid Porous Structures with Bioinspired Functional Gradients

A new type of sheet porous structures with functionally gradients based on triply periodic minimal surfaces (TPMS) is proposed for designing bone scaffolds. The graded structures were generated by constructing branched features with different number of sheets. The design of the structure was formulated mathematically and five types of porous structure with different structural features were used for investigation. The relative density (RD) and surface area to volume (SA/V) ratio of the samples were analyzed using a slice-based approach to confirm their relationships with design parameters. All samples were additively manufactured using selective laser melting (SLM), and their physical morphologies were observed and compared with the designed models. Compression tests were adopted to study the mechanical properties of the proposed structure from the obtained stress-strain curves. The results reveal that the proposed branched-sheet structures could enhance and diversify the physical and mechanical properties, indicating that it is a potential method to tune the biomechanical properties of porous scaffolds for bone tissue engineering (TE).