Relevance of anionic dye properties on water decolorization performance using bone char: Adsorption kinetics, isotherms and breakthrough curves

Preparation, characterisation and applications of bone char, a food waste-derived sustainable material: A review

The production of increasing quantities of by-products is a key challenge for modern society; their valorisation - turning them into valuable compounds with technological applications - is the way forward, in line with circular economy principles. In this review, the conversion of bones (by-products of the agro-food industry) into bone char is described. Bone char is obtained with a process of pyrolysis, which converts the organic carbon into an inorganic graphitic one. Differently from standard biochar of plant origin, however, bone char also contains calcium phosphates, the main component of bone (often hydroxyapatite). The combination of calcium phosphate and graphitic carbon makes bone char a unique material, with different possible uses. Here bone chars' applications in environmental remediation, sustainable agriculture, catalysis and electrochemistry are discussed; several aspects are considered, including the bones used to prepare bone char, the preparation conditions, how these affect the properties of the materials (i.e. porosity, surface area) and its functional properties. The advantages and limitations of bone chars in comparison to traditional biochar are discussed, highlighting the directions the research should take for bone chars' performances to improve. Moreover, an analysis on the sustainability of bone chars' preparation and use is also included.

Efficiency of chemically activated raw and calcined waste fish bone for Adsorption of Cd(II) and Pb(II) from polluted water.. [DOI: 10.21203/rs.3.rs-3103669/v1] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

Bone biochare is used widely as an adsorbent in water pollution control; because of its high surface area and pore volumes . This study is attempting to prepare a low cost adsorbent from waste fish bone by chemical activation, and uses it for the removal of Pb and Cd from polluted water. Two methods were used for preparation of fish bone adsorbents. The first method includes the chemical activation of waste fish bone using different chemical activators ( 0.001 M HNO3, 0.1 M NaOH, 0.5 % H2O2, and ethanol), while the second one includes calcination of waste fish bone after the chemical activation at 600oC. The synthesized fish bone adsorbents were characterized by electron microscopy (SEM), X-ray diffractometer (XRD), X-ray fluorescence (XRF), BET surface area, and Fourier transform infrared (FT-IR). The efficiency of the prepared adsorbents for removal of Pb and Cd were investigated as a function of contact time, solution pH, solution temperature, initial metal concentration, and adsorbent dose. Metal concentrations were measured by atomic absorption spectroscopy . The results reveal that activation of the waste fish bone by 0.1 M NaOH is the suitable for the higher adsorption of Pb and Cd than with the other activators. The maximum adsorption of Pb and Cd on the chemically prepared adsorbent were 99.74 and 99.35 % , respectively at optimum conditions. The results of kinetic adsorption obeyed a pseudo-second-order model. Freundlich and Langmuir isotherms were applied , and the adsorption was found to be fitted well with the Langmuir model. This study ended with the success for preparing an ecofriendly and low cost fish bone adsorbent from the waste fish bone, and used it for the removal of Pb and Cd from polluted water

Efficient lead immobilization by bio-beads containing Pseudomonas rhodesiae and bone char

Mineralization of lead ions (Pb²⁺) to pyromorphite using phosphorus-containing materials is an effective way to remediate lead (Pb) contamination. Bone char is rich in phosphorus, but its immobilization of Pb²⁺ is limited by poor phosphate release. To utilize the phosphorus in bone char and provide a suitable growth environment for phosphate-solubilizing bacteria, bone char and Pseudomonas rhodesiae HP-7 were encapsulated into bio-beads, and the immobilization performance and mechanism of Pb in solution and soil by bio-beads were investigated. The results showed that 137 mg/g of phosphorus was released from bone char in the presence of the HP-7 strain. Pb²⁺ removal efficiency reached 100 % with an initial Pb²⁺ concentration of 1 mM, bone char content of 6 g/L, and bio-bead dosage of 1 %. Most Pb²⁺ was immobilized on the surface of the bio-beads as Pb₅(PO₄)₃Cl. The soil remediation experiments showed a 34 % reduction in the acid-soluble fraction of Pb. The bio-beads showed good stability in long-term (30 d) soil remediation. The present study shows that bone char can be turned into an efficient Pb immobilization material in the presence of phosphate-solubilizing bacteria. Thus, bio-beads are expected to be used in the remediation of Pb-contaminated environments.

Effects of additives on the co-composting of forest residues with cattle manure

Co-composting of forest residues (FR) with cattle manure (CM) results in a low nitrogen (N) conversion efficiency, a low organic matter (OM) degradation rate, and a low quality compost product. This study evaluated the effects of addition of bone charcoal (BC), pumice (PM), or straw biochar (SB) at a ratio of 10 % (w/w) on the co-composting of FR with CM. The highest quality compost was obtained with addition of 10 % PM. Compared with the control (without any additive), PM addition increased the OM degradation rate, the nitrate-N, the available phosphorus, and the available potassium by 25 %, 110 %, 24 %, and 9 %, respectively, and increased the relative abundance of bacteria (Planomicrobium, Flavobacterium, and Pseudomonas) involved in lignocellulose degradation and N transformation. With the addition of PM, the co-composting of FR with CM generated a high quality, useful product in only 39 days.

Value-added materials recovered from waste bone biomass: technologies and applications

As the world population increases, the generation of waste bones will multiply exponentially, increasing landfill usage and posing health risks. This review aims to shed light on technologies for recovering valuable materials (e.g., alkaline earth material oxide such as CaO, hydroxyapatite, beta tri-calcium phosphate, phosphate and bone char) from waste bones, and discuss their potential applications as an adsorbent, catalyst and catalyst support, hydroxyapatite for tissue engineering, electrodes for energy storage, and phosphate source for soil remediation. Waste bone derived hydroxyapatite and bone char have found applications as a catalyst or catalyst support in organic synthesis, selective oxidation, biodiesel production, hydrocracking of heavy oil, selective hydrogenation and synthesis of bioactive compounds. With the help of this study, researchers can gather comprehensive data on studies regarding the recycling of waste bones, which will help them identify material recovery technologies and their applications in a single document. Furthermore, this work identifies areas for further research and development as well as areas for scaling-up, which will lead to reduced manufacturing costs and environmental impact. The idea behind this is to promote a sustainable environment and a circular economy concept in which waste bones are used as raw materials to produce new materials or for energy recovery.

Superior removal of humic acid from aqueous stream using novel calf bones charcoal nanoadsorbent in a reversible process

While the potable water disinfection regimen has significantly reduced waterborne diseases, development of disinfection byproducts (DBP) during this process has brought a global threat to the environment and human health. The most notorious water pollutant, humic acid (HA), transforms into carcinogenic byproducts during the disinfection process (chlorination) of water treatment. HA removal methods are neither economic nor widely available. This study addresses the most urgent global issue of HA removal by developing an innovative and self-regenerative process based on a low-cost and self-regenerative calf bone char (CBC) that removed 92.1-100% of HA. CBC-based HA removal has not been described yet. The developed CBC, as a super adsorbent of HA, was initially characterized by a scanning electron microscope. Various parameters of adsorption/desorption and self-regeneration of CBC adsorbent were experimentally determined. Results show that prepared CBC with a 112 m²/g surface area exhibited adsorption of 38.08 mg/g (HA = 20 mg/L, pH = 4.0) which is several folds higher than the typical amount of HA present in water. The 30 m reaction time was enough to remove HA which is the shorter HA time in comparison to other similar studies. The increase of HA from 0.5 to 5 g/L, raises % HA removal (36.7-99.8%) while a pH decrease (10-4) increases adsorption (12.3-98.3%). The adsorption data fitted well with the pseudo-second-order model and the Langmuir isotherm which demonstrate that adsorption takes place by a monolayer formation. Thermodynamic constants supported the endothermic, spontaneous and reversible nature of adsorption which can attain 100% HA removal. 100% regeneration of exhausted CBC by NaOH further supports the sustainability of the process. CBC as a new adsorbent material thus provides an economical and sustainable water pre-treatment procedure. The present study provides technical guidance for building a cost-effective and scalable process capable of providing clean water.

Waste-to-Resource Strategy to Fabricate Functionalized MOFs Composite Material Based on Durian Shell Biomass Carbon Fiber and Fe3O4 for Highly Efficient and Recyclable Dye Adsorption

Recently, metal–organic frameworks (MOFs), which are porous inorganic–organic hybrid materials consisting of metal ions (clusters or secondary building units) and organic ligands through coordination bonds, have attracted wide attention because of their high surface area, huge ordered porosity, uniform structural cavities, and excellent thermal/chemical stability. In this work, durian shell biomass carbon fiber and Fe₃O₄ functionalized metal–organic framework composite material (durian shell fiber-Fe₃O₄-MOF, DFM) was synthesized and employed for the adsorption removal of methylene blue (MB) from wastewater. The morphology, structure, and chemical elements of the DFM material were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), transmission electron microscope (TEM), and X-ray photoelectron spectroscope (XPS) techniques. Adsorption conditions such as pH, adsorption time, and temperature were optimized. The adsorption isotherm and kinetics results show that the adsorption process of DFM material to MB is more in line with the Freundlich model and pseudo-second-order kinetic model. Using these models, the maximum adsorption capacity of 53.31 mg/g was obtained by calculation. In addition, DFM material could be easily reused through an external magnet and the removal rate of MB was still 80% after five adsorption cycles. The obtained results show that DFM composite material, as an economical, environmentally friendly, recyclable new adsorbent, can simply and effectively remove MB from wastewater.

Removal of potentially toxic elements from contaminated soil and water using bone char compared to plant- and bone-derived biochars: A review

Conversion of hazardous waste materials to value-added products is of great interest from both agro-environmental and economic points of view. Bone char (BC) has been used for the removal of potentially toxic elements (PTEs) from contaminated water, however, its potential BC for the immobilization of PTEs in contaminated water and soil compared to bone (BBC)- and plant (PBC)-derived biochars has not been reviewed yet. This review presents an elaboration for the potentials of BC for the remediation of PTEs-contaminated water and soil in comparison with PBC and BBC. This work critically reviews the preparation and characterization of BC, BBC, and PBC and their PTEs removal efficiency from water and soils. The mechanisms of PTE removal by BC, BBC, and PBC are also discussed in relation to their physicochemical characteristics. The review demonstrates the key opportunities for using bone waste as feedstock for producing BC and BBC as promising low-cost and effective materials for the remediation of PTEs-contaminated water and soils and also elucidates the possible combinations of BC and BBC aiming to effectively immobilize PTEs in water and soils.

A Review of the Modeling of Adsorption of Organic and Inorganic Pollutants from Water Using Artificial Neural Networks

The application of artificial neural networks on adsorption modeling has significantly increased during the last decades. These artificial intelligence models have been utilized to correlate and predict kinetics, isotherms, and breakthrough curves of a wide spectrum of adsorbents and adsorbates in the context of water purification. Artificial neural networks allow to overcome some drawbacks of traditional adsorption models especially in terms of providing better predictions at different operating conditions. However, these surrogate models have been applied mainly in adsorption systems with only one pollutant thus indicating the importance of extending their application for the prediction and simulation of adsorption systems with several adsorbates (i.e., multicomponent adsorption). This review analyzes and describes the data modeling of adsorption of organic and inorganic pollutants from water with artificial neural networks. The main developments and contributions on this topic have been discussed considering the results of a detailed search and interpretation of more than 250 papers published on Web of Science ® database. Therefore, a general overview of the training methods, input and output data, and numerical performance of artificial neural networks and related models utilized for adsorption data simulation is provided in this document. Some remarks for the reliable application and implementation of artificial neural networks on the adsorption modeling are also discussed. Overall, the studies on adsorption modeling with artificial neural networks have focused mainly on the analysis of batch processes (87%) in comparison to dynamic systems (13%) like packed bed columns. Multicomponent adsorption has not been extensively analyzed with artificial neural network models where this literature review indicated that 87% of references published on this topic covered adsorption systems with only one adsorbate. Results reported in several studies indicated that this artificial intelligence tool has a significant potential to develop reliable models for multicomponent adsorption systems where antagonistic, synergistic, and noninteraction adsorption behaviors can occur simultaneously. The development of reliable artificial neural networks for the modeling of multicomponent adsorption in batch and dynamic systems is fundamental to improve the process engineering in water treatment and purification.

Multi-component adsorption study by using bone char: modelling and removal mechanisms

Highly efficient simultaneous removal of paracetamol and Cu²⁺ ions from aqueous solutions was accomplished by using bovine bone char (BC). The adsorption behaviour was determined by kinetic and equilibrium studies of both single and binary system solutions. BC is a predominantly mesoporous material with a surface area of 103 m² g^-1. The influence of the initial pH on Cu²⁺ removal was tested, suggesting that the optimal pH was 3.0. The removal of paracetamol from single and binary systems was 9.45 and 12.7%, respectively. On the other hand, the Cu²⁺ removal was 36.2% for a single system, suggesting a higher affinity for BC. Moreover, in the case of binary mixtures, the presence of paracetamol led to an enhanced affinity of Cu²⁺ due to a synergistic/cooperative mechanism, which led to a copper removal of 97.3%. The cooperative model was successfully adjusted to the equilibrium data of the binary systems. The modelling results indicated the formation of a first adsorption layer where paracetamol and copper are retained, and a second layer with a great affinity for copper ions after the formation of a Cu-paracetamol complex, leading to higher removal of Cu²⁺.

Fabrication of Stable MIL-53(Al) for Excellent Removal of Rhodamine B

Adsorptive purification of organic dyes in wastewater is significant to protect the water environment. Herein, MIL-53(Al) was successfully fabricated through a facile and versatile solvothermal strategy. The stability of MIL-53(Al) under high temperature, acid, base, and peroxide conditions was investigated. The porous MIL-53(Al) had high chemical stability, and the thermal stability reached up to 500 °C, which provided a good foundation for dye removal. MIL-53(Al) showed excellent adsorption performance. The maximum adsorption capacity of MIL-53(Al) for rhodamine B (RhB) can reach 1547 mg g^-1 under 303 K, and the corresponding removal efficiency exceeded 90% at the equilibrium time (120 min). The Langmuir model and pseudo-second-order model can well fit RhB adsorption on MIL-53(Al). Thermodynamic study and activation energy values over the range of 298-323 K revealed that the adsorption of RhB was a spontaneous and endothermic physical process in nature. The batch experimental results, X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared (FTIR) spectroscopy analyses suggested that the hydrogen bonding and electrostatic interactions between the hydroxyl/carboxyl groups of MIL-53(Al) and RhB were the primary adsorption mechanisms. Besides, MIL-53(Al) had a higher selectivity to RhB than the coexisting ions in aqueous solution and a superior adsorption performance after five cycles.

Adsorption Performance of Cd(II) by Chitosan-Fe3O4-Modified Fish Bone Char

In order to develop a low-cost, fast, and efficient adsorbent, the fish bone charcoal B₆₀₀ prepared at 600 °C was modified by chitosan (Cs) and Fe₃O₄ to produce the material Cs-Fe₃O₄-B₆₀₀. Results showed that Cs-Fe₃O₄-B₆₀₀ had magnetic responsiveness and can achieve solid–liquid separation, macropores disappeared, pore volume and specific surface area are increased, and amino functional groups appear on the surface. The adsorption process of Cd(II) by Cs-Fe₃O₄-B₆₀₀ conformed best to the pseudo-second order kinetics model and the Langmuir model, respectively. The behavior over a whole range of adsorption was consistent with chemical adsorption being the rate-controlling step, which is a very fast adsorption process, and the isothermal adsorption is mainly monolayer adsorption, which belongs to favorable adsorption. In addition, the saturated adsorption capacity obtained for the Cs-Fe₃O₄-B₆₀₀ to Cd(II) was 64.31 mg·g⁻¹, which was 1.7 times than B₆₀₀. The structure and morphology of Cs-Fe₃O₄-B₆₀₀ were characterized through SEM-EDS, TEM, FTIR, and XRD, indicating that the main mechanism of Cs-Fe₃O₄-B₆₀₀ and Cd(II) is mainly the complexation of amino groups, and it also includes part of the ion exchange between Cd(II) and Fe₃O₄. Therefore, Cs-Fe₃O₄-B₆₀₀ can be employed as an effective agent for remediation of Cd contaminated water.

Feasibility of magnetic nano adsorbent impregnated with activated carbon from animal bone waste: Application for the chromium (VI) removal

Chromium is the heavy metal which existing in the effluents cause extensive discomfort to the environmental components. Bone waste is widely generated in food processing industries and restaurants. It is now used by switching into activated carbon. By co-precipitation procedure, the activated carbon is coated with a nano adsorbent. The Fe₃O₄-BAC adsorbent potential was established in this study via several batch tests. The adsorbing adverts had super magnetic behavior, and the magnetization value was 22 emu/g. The SEM imaging of the Fe₃O₄-BAC shows an improved morphology of 100-446 nm, and the nanoparticles were monodispersed. The present investigation also delves into the study of system parameters on the removal of metal ions. Optimal adsorption has been found at the acidic pH at the contact time of 60min for the adsorbent amount of 5 g/L. Maximum capacity of adsorption by nano adsorbent was 27.86 mg/g. Thermodynamic and isotherm tests have established the process viability. In addition, the kinetic studies establish the inclination of the studied Fe₃O₄-BAC towards pseudo-first order models. Hence, Fe₃O₄-BAC could be potential adsorbent to remove chromium from an aqueous solution.

Physicochemical assessment of anionic dye adsorption on bone char using a multilayer statistical physics model

The statistical physics modeling is a reliable approach to interpret and understand the adsorption mechanism of both organic and inorganic adsorbates. Herein, a theoretical study of the adsorption mechanism of anionic dyes, namely reactive blue 4 (RB4), acid blue 74 (AB74), and acid blue 25 (AB25), on bone char was performed with a multilayer statistical physics model. This model was applied to fit the equilibrium adsorption data of these dyes at 298-313 K and pH 4. Results indicated that the global number of formed dye layers on the bone char varied from 1.62 to 2.24 for RB4, AB74, and AB25 dyes depending on the solution temperature where the saturation adsorption capacities ranged from 0.08 to 0.12 mmol/g. Dye molecular aggregation was also identified for these dyes where dimers and trimers prevailed at different operating conditions especially for adsorbates RB4 and AB74. Adsorption mechanism of these dyes was multimolecular and endothermic with adsorption energies from 10.6 to 20.8 kJ/mol where van der Waals interactions and hydrogen bonding could be present. This investigation contributes to understand the physicochemical variables associated to dye adsorption using low-cost adsorbents as bone char.

Study the Use of Activated Carbon and Bone Char on the Performance of Gravity Sand-Bag Water Filter

In this study, granulated activated charcoal (GAC) and bio charcoal (BC) is used as a filler in P3 biosand bag filter to study their filtration performance against a range of fluoride impurities from 1–1400 mg/L. A set of experiments are done to analyze the filtration efficiency of the sandbag filter against fluoride impurities after incorporating different amounts (e.g., 0.2, 2 kg) and a combination of GAC and BC. A combination of filler GAC and BC (1 kg each) have exhibited excellent results with 100% fluoride removal efficiency against 5 mg/L fluoride impurities for an entire experimental time of 165 min. It is because of the synergetic effect of adsorption caused by the high surface area (739 m²/g) of GAC and hydroxyapatite groups in BC. The data from remediation experiments using individual GAC and BC are fitted into the Langmuir and Freundlich Isotherm Models to check their adsorption mechanism and determine GAC and BC’s maximum adsorption capacity (Q_m). The remediation data for both GAC and BC have shown the better fitting to the Langmuir Isotherm Model with a high R² value of 0.994 and 0.970, respectively, showing the excellent conformity with monolayer adsorption. While the GAC and BC have presented negative Kf values of −1.08 and −0.72, respectively, for Freundlich Model, showing the non-conformity to multilayer adsorption. The Q_m values obtained from Langmuir Model for GAC is 6.23 mg/g, and for BC, it is 9.13 mg/g. The pH study on adsorption efficiency of individual GAC and BC against 5 mg/L of fluoride impurities indicates the decrease in removal efficiency with an increase in pH from 3 to 9. For example, BC has shown removal efficiency of 99.8% at pH 3 and 99.5% at pH 9, while GAC has exhibited removal efficiency of 96.1% at pH 3 and 95.9% at pH 9. Importantly, this study presents the significance of the synergetic application of GAC and BC in the filters, where GAC and BC are different in their origin, functionalities, and surface characteristics.

Preparation of Acid- and Alkali-Modified Biochar for Removal of Methylene Blue Pigment

Walnut shell biochar (WSC) and wood powder biochar (WPC) prepared using the limited oxygen pyrolysis process were used as raw materials, and ZnCl₂, KOH, H₂SO₄, and H₃PO₄ were used to modify them. The evaluation of the liquid-phase adsorption performance using methylene blue (MB) as a pigment model showed that modified biochar prepared from both biomasses had a mesoporous structure, and the pore size of WSC was larger than that of WPC. However, the alkaline modified was more conducive to the formation of pores in the biomass-modified biochar materials; KOH treatment resulted in the highest modified biochar-specific surface area. The isothermal adsorption of MB by the two biomass pyrolysis charcoals conformed to the Freundlich equation, and the adsorption process conformed to the quasi-second-order kinetic equation, which is mainly physical adsorption. The large number of oxygen-containing functional groups on the particle surface provided more adsorption sites for MB adsorption, which was beneficial to the adsorption reactions. The adsorption effects of woody biomass were obviously higher than that of shell biomass, and the adsorption capacities of the two raw materials' pyrolysis charcoal were in the order of WPC > WSC. The adsorption effects of different treatment reagents on MB were in the order ZnCl₂ > KOH > H₃PO₄ > H₂SO₄. The maximum adsorption capacities of the two biomass treatments were 850.9 mg/g for WPC with ZnCl₂ treatment and 701.3 mg/g for WSC with KOH treatment.

Lead sorption characteristics of various chicken bone part-derived chars

Recycling food waste for beneficial use is becoming increasingly important in resource-limited economy. In this study, waste chicken bones of different parts from restaurant industry were pyrolyzed at 600 °C and evaluated for char physicochemical properties and Pb sorption characteristics. Lead adsorption isotherms by different chicken bone chars were carried out with initial Pb concentration range of 1-1000 mg L^-1 at pH 5. The Pb adsorption data were better described by the Langmuir model (R² = 0.9289-0.9937; ARE = 22.7-29.3%) than the Freundlich model (R² = 0.8684-0.9544; ARE = 35.4-72.0%). Among the chars derived from different chicken bone parts, the tibia bone char exhibited the highest maximum Pb adsorption capacity of 263 mg g^-1 followed by the pelvis (222 mg g^-1), ribs (208 mg g^-1), clavicle (179 mg g^-1), vertebrae (159 mg g^-1), and humerus (135 mg g^-1). The Pb adsorption capacities were significantly and positively correlated with the surface area, phosphate release amount, and total phosphorus content of chicken bone chars (r ≥ 0.9711). On the other hand, approximately 75-88% of the adsorbed Pb on the chicken bone chars was desorbable with 0.1 M HCl, indicating their recyclability for reuse. Results demonstrated that chicken bone char could be used as an effective adsorbent for Pb removal in wastewater.

Bone char as a green sorbent for removing health threatening fluoride from drinking water

Millions of people around the world suffer from or prone to health problems caused by high concentration of fluoride in drinking water sources. One of the environmentally friendly and cost-effective ways for removing fluoride is the use of bone char. In this review, the structural properties and binding affinity of fluoride ions from different water sources was critically discussed. The effect of experimental conditions on enhancing the adsorption capacity of fluoride ions using bone char samples was addressed. It appears that surface properties, and conditions of the bone char production such as temperature and residence time play an important role in designing the optimal fluoride removal process. The optimum temperature for fluoride removal seems to be in the range of 500-700 °C and a residence time of 2 h. Applying various equilibrium adsorption isotherms for understanding fluoride adsorption mechanism was presented. The effect of bone char modification with different elements were discussed and recommendations for a further increase in the removal efficiency was proposed. Cost of bone char production and large-scale treatment systems were also discussed based on information available from scientific and commercial sources. Challenges with existing domestic defluoridation designs were highlighted and suggestions for new conceptual designs were provided.

Fixed-bed study for bone char adsorptive removal of refractory organics from electrodialysis concentrate produced by petroleum refinery

Water reuse in industrial processes has been an increasing need encouraged in recent years. However, as the streams are recycled, solutes accumulate, thus requiring purification techniques. Membrane processes (reverse osmosis and electrodialysis) have been implemented and in order to increase the reuse of water at its highest level, crystallization has been evaluated to remove salts from the concentrate produced and get a feasible disposal. Nevertheless, contaminants affect the crystallization performance, thus making the removal of residual organics important for both the efficiency of crystallization and the increase of water reuse. In this context, aiming at establishing a sustainable virtuous circle, bone char (0.5-1.4 mm particle size, mesoporous structure) was used to remove refractory organics from an electrodialysis concentrate effluent (C-EDR) from a Brazilian petroleum refinery, at a lab-scale, in a fixed-bed adsorption column. Bone char selectively and partially removed the refractory organics, a complex mixture of long-chain hydrocarbons, aromatic compounds, carboxylic acids, amines and amides. The maximum adsorption capacity increased with the increase in bed depth and reduction in flow rate. A maximum removal of 35.60 mg g^-1 was achieved for the highest bed depth evaluated (12.9 cm). The breakthrough curves indicated that bone char could adsorb part of the organic compounds from the C-EDR. The scaling up was possible for the C/C₀ ratios of 0.55, 0.60 and 0.65, providing a service time at about 16 days for 45% removal efficiency for typical real operational conditions used in the refinery.

Enhanced Defluoridation Capacity From Aqueous Media via Hydroxyapatite Decorated With Carbon Nanotube

In this work, the potential of a novel hydroxyapatite decorated with carbon nanotube composite (CNT-HAP) for fluoride removal was investigated. The synthesized CNT-HAP composite was systematically characterized by X-ray diffraction(XRD), Fourier Transform infrared spectroscopy(FTIR), scanning electron microscope (SEM) and Brunauer–Emmett–Teller(BET). Batch adsorption experiments were conducted to investigate the defluorination capacity of CNT-HAP. The CNT-HAP composite has a maximum adsorption capacity of 11.05 mg·g⁻¹ for fluoride, and the isothermal adsorption data were fitted by the Freundlich model to calculate the thermodynamic parameters. Thermodynamic analysis implies that the adsorption of fluoride on CNT-HAP is a spontaneous process. Furthermore, the adsorption of fluoride follows pseudo-second-order model. The effects of solution pH, co-existing anions and reaction temperature on defluorination efficiency were examined to optimize the operation conditions for fluoride adsorption. It is found that the optimized pH-value for fluoride removal by CNT-HAP composite is 6. In addition, among five common anions studied in this work, the presence of HCO3- and PO43- could considerably affect the fluoride removal by CNT-HPA in aqueous media. Finally, the underlying mechanism for the fluoride removal by CNT-HAP is analyzed, and an anion exchange process is proposed.

The adsorption study of Royal Blue Tiafix and Black Tiassolan dyes using bone char as adsorbent

In this study, the potential of bone char for Royal Blue Tiafix and Black Tiassolan dyes adsorption from aqueous solutions was evaluated. The adsorbent was characterized physically and chemically by adsorption/desorption of N2 at 77 K, scanning electron microscopy, X-ray diffraction, and infrared spectroscopy. The equilibrium adsorption results for bone char can be successfully modeled by the Langmuir and Freundlich isotherms. Pseudo-first-order and pseudo-second-order models were used to describe the kinetic data and rate constants were evaluated. Kinetics of each dye was found to follow pseudo-second-order rate kinetic model, with great correlation (higher than 0.99). In order to reduce the number of experiments to achieve better dye removal efficiency, a 2³ full factorial design with three central points and six axial points was applied in the equilibrium experiments. The variables analyzed were agitation, temperature, and pH.

Decontamination of arsenic(V)-contained liquid phase utilizing Fe3O4/bone char nanocomposite encapsulated in chitosan biopolymer

The application of a novel nanocomposite synthesized through the combination of Fe₃O₄ nanoparticles and bone char particles for the adsorption of As(V) ions in the aquatic medium was investigated. As-prepared nanocomposite was immobilized by using chitosan biopolymer. The characterization of the nanocomposite was performed via SEM, XRD, FT-IR, and BET together with the determination of zero-point charge of the adsorbent surface. As results, the obtained experimental data were fitted well with pseudo-first-order kinetic model (R² = 0.997) and Langmuir isotherm model (R² = 0.990) with the maximum adsorption capacity of about 112 μg/g. Increasing the dosage of nanocomposite and initial solute concentration led to increasing the adsorption capacity of As(V) ions, while decreasing the solution temperature resulted in the enhanced adsorption process. According to the results of thermodynamic study, the adsorption of As(V) ions onto the nanocomposite was spontaneous and exothermic in nature.

Fungal biomass as biosorbent for the removal of Acid Blue 161 dye in aqueous solution

Physical and thermal treatment was used to inactivate Trametes sp. SC-10 fungus. The resulting biomass was named BTV, characterized by analytical techniques such as SEM, EDX, FTIR, BET, and Barrett-Joyner-Halenda (BJH) model. pH, kinetic, and equilibrium adsorption studies with the Acid Blue 161 (AB-161) dye were investigated at 303.15 K. The kinetics of the biosorption process were examined at 600.00 and 1300 mg L^-1, using pseudo-first-order, pseudo-second-order, and Avrami fractional-order models. The maximum biosorption capacity of BTV for AB-161 dye was 221.6 mg g^-1. Considering the biosorption data and the functional groups of BTV, it can be inferred that the sorption mechanism of AB-161 is regulated by electrostatic interactions between ionized dye molecules and negative charges on BTV in an aqueous solution. Finally, the BTV was tested with a simulated effluent with 89.47% efficiency, presenting the BTV as a biosorbent for real effluents polluted with dyes.

Cow bones char as a green sorbent for fluorides removal from aqueous solutions: batch and fixed-bed studies

Cow bone char was investigated as sorbent for the defluoridation of aqueous solutions. The cow bone char was characterized in terms of its morphology, chemical composition, and functional groups present on the bone char surface using different analytical techniques: SEM, EDS, N₂-BET method, and FTIR. Batch equilibrium studies were performed for the bone chars prepared using different procedures. The highest sorption capacities for fluoride were obtained for the acid washed (q = 6.2 ± 0.5 mg/g) and Al-doped (q = 6.4 ± 0.3 mg/g) bone chars. Langmuir and Freundlich models fitted well the equilibrium sorption data. Fluoride removal rate in batch system is fast in the first 5 h, decreasing after this time until achieving equilibrium due to pore diffusion. The presence of carbonate and bicarbonate ions in the aqueous solution contributes to a decrease of the fluoride sorption capacity of the bone char by 79 and 31 %, respectively. Regeneration of the F-loaded bone char using 0.5 M NaOH solution leads to a sorption capacity for fluoride of 3.1 mg/g in the second loading cycle. Fluoride breakthrough curve obtained in a fixed-bed column presents an asymmetrical S-shaped form, with a slow approach of C/C ₀ → 1.0 due to pore diffusion phenomena. Considering the guideline value for drinking water of 1.5 mg F^-/L, as recommended by World Health Organization, the service cycle for fluoride removal was of 71.0 h ([F^-]_feed ∼ 9 mg/L; flow rate = 1 mL/min; m _sorbent = 12.6 g). A mass transfer model considering the pore diffusion was able to satisfactorily describe the experimental data obtained in batch and continuous systems.

Synthesis of malachite@clay nanocomposite for rapid scavenging of cationic and anionic dyes from synthetic wastewater

Synthesis of malachite@clay nanocomposite was successfully carried out for the removal of cationic (Methylene Blue, MB) and anionic dyes (Congo Red, CR) from synthetic wastewater. Nanocomposite was characterized by TEM, SEM, FT-IR, EDS analysis and zeta potential. TEM analysis indicated that the particle diameter of nanocomposite was in the range of 14 to 23nm. Various important parameters viz. contact time, concentration of dyes, nanocomposite dosage, temperature and solution pH were optimized to achieve maximum adsorption capacity. In the case of MB, removal decreased from 99.82% to 93.67% while for CR, removal decreased from 88.55% to 75.69% on increasing dye concentration from 100 to 450mg/L. pH study confirmed the higher removal of CR in acidic range while MB removal was higher in alkaline range. Kinetic study revealed the applicability of pseudo-second-order model for the adsorption of both dyes. Negative values of ΔG⁰ for both systems suggested the feasibility of dye removal and support for spontaneous adsorption of CR and MB on nanocomposite. Nanocomposite showed 277.77 and 238.09mg/g Langmuir adsorption capacity for MB and CR respectively. Desorption of dyes from the dye loaded nanocomposite was easily carried out with acetone. The results indicate that the prepared malachite@clay nanocomposite is an efficient adsorbent with high adsorption capacity for the aforementioned dyes.