Recent advances in nano-Fenton catalytic degradation of emerging pharmaceutical contaminants

Analysis of factors influencing on Electro-Fenton and research on combination technology (II): a review

The principle of Fenton reagent is to produce ·OH by mixing H2O2 and Fe2+ to realize the oxidation of organic pollutants, although Fenton reagent has the advantages of non-toxicity and short reaction time, but there are its related defects. The Fenton-like technology has been widely studied because of its various forms and better results than the traditional Fenton technology in terms of pollutant degradation efficiency. This paper reviews the electro-Fenton technology among the Fenton-like technologies and provides an overview of the homogeneous electro-Fenton. It also focuses on summarizing the effects of factors such as H2O2, reactant concentration, reactor volume and electrode quality, reaction time and voltage (potential) on the efficiency of electro-Fenton process. It is shown that appropriate enhancement of H2O2 concentration, voltage (potential) and reaction volume can help to improve the process efficiency; the process efficiency also can be improved by increasing the reaction time and electrode quality. Feeding modes of H2O2 have different effects on process efficiency. Finally, a considerable number of experimental studies have shown that the combination of electro-Fenton with ultrasound, anodic oxidation and electrocoagulation technologies is superior to the single electro-Fenton process in terms of pollutant degradation.

Highly efficient catalytic Fenton-Like reactions of bimetallic Fe/Cu chelated on radiation functionalized nonwoven fabric for pollutant control

A remarkably efficient and affordable Fe/Cu bimetallic catalyst featuring a substantial light energy utilization and compatibility with a sizable substrate was developed for Fenton-like reactions aimed at pollutant control. Specifically, a novel strategy was employed to synthesize high-density metal sites (Fe:Cu ≈ 3:1) robustly embedded on polyethylene/polyethylene terephthalate nonwoven fabric (PE/PET NWF) via radiation-induced graft polymerization (RIGP) and subsequent chemical modification, labeled as Fe/Cu-PPAO. Its high effectiveness was demonstrated by degrading 50 mg/L of tetracycline hydrochloride within 30 min in the presence of H2O2 under simulate sunlight irradiation. It was investigated that amidoxime groups regulated the optical gaps and HOMO-LUMO gaps of metal ions to enable the absorption of a broader spectrum light while the Cu2+ facilitated the transfer of electrons between the bimetal ions to achieve an improved reaction path. Furthermore, X-ray absorption fine structure (XAFS) and density functional theory (DFT) calculations further revealed its special complex state and delicate electronic structure between bimetal ions and amidoxime groups. Our study offers a new strategy to synthesize high-density bimetallic sites catalyst for environmental remediation and pushes forward insight into understanding the catalytic mechanism of bimetallic Fenton-like catalysts.

Occurrence and fate of pharmaceutical pollutants in wastewater: Insights on ecotoxicity, health risk, and state-of-the-art removal

Pharmaceutical active compound (PhAC) residues are considered an emerging micropollutant that enters the aquatic environment and causes harmful ecotoxicity. The significant sources of PhACs in the environment include the pharmaceutical industry, hospital streams, and agricultural wastes (animal husbandry). Recent investigations demonstrated that wastewater treatment plants (WWTPs) are an important source of PhACs discharging ecosystems. Several commonly reported that PhACs are detected in a range level from ng L-1 to μg L-1 concentration in WWTP effluents. These compounds can have acute and chronic adverse impacts on natural wildlife, including flora and fauna. The approaches for PhAC removals in WWTPs include bioremediation, adsorption (e.g., biochar, chitosan, and graphene), and advanced oxidation processes (AOPs). Overall, adsorption and AOPs can effectively remove PhACs from wastewater aided by oxidizing radicals. Heterogeneous photocatalysis has also proved to be a sustainable solution. Bioremediation approaches such as membrane bioreactors (MBRs), constructed wetlands (CWs), and microalgal-based systems were applied to minimize pharmaceutical pollution. Noteworthy, applying MBRs has illustrated high removal efficiencies of up to 99%, promising prospective future. However, WWTPs should be combined with advanced solutions, e.g., AOPs/photodegradation, microalgae-bacteria consortia, etc., to treat and minimize their accumulation. More effective and novel technologies (e.g., new generation bioremediation) for PhAC degradation must be investigated and specially designed for a low-cost and full-scale. Investigating green and eco-friendly PhACs with advantages, e.g., low persistence, no bioaccumulation, less or non-toxicity, and environmentally friendly, is also necessary.

Degradation of reactive red 198 dye from aqueous solutions by combined technology advanced sonofenton with zero valent iron: Characteristics/ effect of parameters/kinetic studies

Dyes are one of the most common contaminants in industrial effluents, whose continuous release into the environment has become an increasing global concern. In this work, nanoparticles of zero-valent iron (NZVI) were synthesized using the chemical regeneration method ،and were utilized for the first time as a catalyst in the advanced Sono-Nano-Fenton hybrid method for the decomposition of Reactive Red 198 (RR198). The properties of zero-valent iron nanoparticles were analyzed using SEM and XRD. The effect of pH, initial dye concentration, nanoparticle dosage, zero-valent iron and H2O2 concentration on the decomposition efficiency of Red Reactive 198 was investigated. Comparing the efficiency of Reactivate 198 dye degradation in Sonolysis, Sono-NZVI, Sono-H2O2 and Sono-Nano Fenton processes showed that 97 % efficiency was achieved by the Sono-Nano Fenton process in 60 min. The kinetics of the removal process showed that this process follows pseudo-first-order kinetics and the Langmuir-Hinshelwood model. The results indicate that the effectiveness of the ultrasonic process in removing resistant organic pollutants such as dyes increases tremendously with the synergy of the Fenton process.

Recent progress in mineralization of emerging contaminants by advanced oxidation process: A review

Emerging contaminants are chemicals generated due to the usage of pesticide, endocrine disrupting compounds, pharmaceuticals, and personal care products and are liberated into the environment in trace quantities. The emerging contaminants eventually become a greater menace to living beings owing to their wide range and inhibitory action. To diminish these emerging contaminants from the environment, an Advanced Oxidation Process was considered as an efficient option. The Advanced Oxidation Process is an efficient method for mineralizing fractional or generous contaminants due to the generation of reactive species. The primary aim of this review paper is to provide a thorough knowledge on different Advanced Oxidation Process methods and to assess their mineralization efficacy of emerging contaminants. This study indicates the need for an integrated process for enhancing the treatment efficiency and overcoming the drawbacks of the individual Advanced Oxidation Process. Further, its application concerning technical and economic aspects is reviewed. Until now, most of the studies have been based on lab or pilot scale and do not represent the actual scenario of the emerging contaminant mineralization. Thus, the scaling up of the process was discussed, and the major challenges in large scale implementation were pointed out.

The influence of pH and dissolved organic carbon on the ecotoxicity of ampicillin and clarithromycin

The impacts of water chemistry properties including pH and dissolved organic carbon (DOC) on the ecotoxicity of active pharmaceutical ingredients (APIs) are increasingly evident. These impacts are a result of alterations in API bioavailability: pH regulates the bioavailability of many ionizable APIs via chemical speciation, whereas DOC interacts with several APIs to inhibit the APIs from traversing the membrane system of organisms. In this study, we examined the influences of pH and DOC on the bioavailability of ampicillin (AMP) and clarithromycin (CLA) with the help of a bioavailability model. The effects on bioavailability were quantified by ecotoxicity observed in cyanobacteria growth inhibition tests with Microcystis aeruginosa PCC7806. The median effect concentration (96 h-EC50total) of AMP increased by 5-fold when pH raised from 7.4 to 9.0, suggesting the zwitterionic AMP+/- species being higher in bioavailability than the negatively charged AMP- species. CLA ecotoxicity showed no significant pH-dependency, suggesting CLA+ and CLA0 species to be equally bioavailable, albeit it correlated significantly with M. aeruginosa growth rate in negative controls. In addition, DOC demonstrated no significant effects on the ecotoxicity of AMP or CLA. Overall, together with earlier results on ciprofloxacin, our data show that bioavailability relations with pH and DOC are variable among different antibiotics. Factors other than chemical speciation alone could play a role in their bioavailability, such as their molecular size and polarity.

Biochar-based geopolymer nanocomposite for COD and phenol removal from agro-industrial biorefinery wastewater: Kinetic modelling, microbial community, and optimization by response surface methodology

Agro-industrial biorefinery effluent (AIBW) is considered a highly polluting source responsible for environmental contamination. It contains high loads of chemical oxygen demand (COD), and phenol, with several other organic and inorganic constituents. Thus, an economic treatment approach is required for the sustainable discharge of the effluent. The long-term process performance, contaminant removal and microbial response of AIBW to rice straw-based biochar (RSB) and biochar-based geopolymer nanocomposite (BGC) as biosorbents in an activated sludge process were investigated. The adsorbents operated in an extended aeration system with a varied hydraulic retention time of between 0.5 and 1.5 d and an AIBW concentration of 40-100% for COD and phenol removal under standard conditions. Response surface methodology was utilised to optimize the process variables of the bioreactor system. Process results indicated a significant reduction of COD (79.51%, 98.01%) and phenol (61.94%, 74.44%) for BEAS and GEAS bioreactors respectively, at 1 d HRT and AIBW of 70%. Kinetic model analysis indicated that the Stover-Kincannon model best describes the system functionality, while the Grau model was better in predicting substrate removal rate and both with a precision of between R2 (0.9008-0.9988). Microbial communities examined indicated the abundance of genera, following the biosorbent addition, while RSB and BGC had no negative effect on the bioreactor's performance and bacterial community structure of biomass. Proteobacteria and Bacteroidetes were abundant in BEAS. While the GEAS achieved higher COD and phenol removal due to high Nitrosomonas, Nitrospira, Comamonas, Methanomethylovorans and Acinetobacter abundance in the activated sludge. Thus, this study demonstrated that the combination of biosorption and activated sludge processes could be promising, highly efficient, and most economical for AIBW treatment, without jeopardising the elimination of pollutants or the development of microbial communities.

Subsurface flow constructed wetlands for treating of simulated cadmium ions-wastewater with presence of Canna indica and Typha domingensis

The presence of toxic cadmium ions in the wastewater resulted from industrial sector forms the critical issue for public health and ecosystem. This study determines the ability of four vertical subsurface flow constructed wetlands units in the treatment of simulated wastewater laden with cadmium ions. This was achieved through using sewage sludge byproduct as alternative for the traditional sand to be substrate for aforementioned units in order to satisfy the sustainable concepts; however, Canna indica and Typha domingensis can apply to enhance the cadmium removal. The performance of constructed wetlands has been evaluated through monitoring of the pH, dissolved oxygen (DO), temperature, and concentrations of cadmium (Cd) in the effluents for retention time (0.5-120 h) and metal concentration (5-40 mg/L). The results demonstrated that the Cd removal percentage was exceeded 82% beyond 5 days and for concentration of 5 mg/L; however, this percentage was decreased with smaller retention time and higher metal concentration. The Grau second-order kinetic model accurately simulated the measurements of effluent Cd concentrations as a function of retention times. The FT-IR analysis indicated the existence of certain functional groups capable of enhancing the Cd removal. The treated wastewater's pH, DO, temperature, total dissolved solids (TDS), and electrical conductivity (EC) all meet the requirements for irrigation water.

Evaluation of the photodegradation activity of bismuth oxoiodide/bismuth sub-carbonate nanocatalyst: Experimental design and the mechanism study

In this study, a binary BiOI/(BiO)2CO3 catalyst was prepared and used for sulfasalazine (SSZ) photodegradation in an aqueous phase. The semiconductors were identified by XRD, SEM-EDX, and UV-Vis diffuse reflectance spectroscopy (DRS) methods. Applying the Kubelka-Munk model on DRS results, the band gap energies of 2.09, 3.5, and 2.07 eV were obtained for BiOI, (BiO)2CO3, and BiOI/(BiO)2CO3 samples. pHpzc values of 6.3, 10.1, and 8.1 were estimated for BiOI, (BiO)2CO3, and BiOI/(BiO)2CO3, respectively. After observing the boosted photocatalytic activity by the coupled system, the interaction effects of the influencing variables in SSZ photodegradation were evaluated via the response surface methodology (RSM) approach. The optimal RSM-run conditions were 8.5 ppm SSZ at pH 8, which contained 0.28 g/L of the BiOI/(BiO)2CO3 catalyst and 29 min illumination time, resulting in 87% SSZ photodegradation. The effects of some scavenging agents were also studied to elucidate the relative roles of the reactive species in the SSZ photodegradation by the proposed catalyst, that is, hydroxyl radicals ∼ photoinduced electrons > superoxide radicals ∼ photoinduced holes. The proposed catalyst retained good activity after 5 successive reusing runs.

Hydrogen Bond-Induced Activation of Photocatalytic and Piezophotocatalytic Properties in Calcium Nitrate Doped Electrospun PVDF Fibers

In this study, polyvinylidene fluoride (PVDF) fibers doped with hydrated calcium nitrate were prepared using electrospinning. The samples were analyzed using scanning electron microscopy (SEM), X-ray diffraction (XRD), optical spectroscopy, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), Raman, and photoluminescence (PL) spectroscopy. The results are complementary and confirm the presence of chemical hydrogen bonding between the polymer and the dopant. Additionally, there was a significant increase in the proportion of the electroactive polar beta phase from 72 to 86%. It was shown that hydrogen bonds acted as a transport pathway for electron capture by the conjugated salt, leading to more than a three-fold quenching of photoluminescence. Furthermore, the optical bandgap of the composite material narrowed to the range of visible light energies. For the first time, it the addition of the salt reduced the energy of the PVDF exciton by a factor of 17.3, initiating photocatalytic activity. The calcium nitrate-doped PVDF exhibited high photocatalytic activity in the degradation of methylene blue (MB) under both UV and visible light (89 and 44%, respectively). The reaction rate increased by a factor of 2.4 under UV and 3.3 under visible light during piezophotocatalysis. The catalysis experiments proved the efficiency of the membrane design and mechanisms of catalysis are suggested. This study offers insight into the nature of chemical bonds in piezopolymer composites and potential opportunities for their use.

Removal of organic pollutants in shale gas fracturing flowback and produced water: A review

Shale gas has been developed as an alternative to conventional energy worldwide, resulting in a large amount of shale gas fracturing flowback and produced water (FPW). Previous studies focus on total dissolved solids reduction using membrane desalination. However, there is a lack of efficient and stable techniques to remove organic pollutants, resulting in severe membrane fouling in downstream processes. This review focuses on the concentration and chemical composition of organic matter in shale gas FPW in China, as well as the hazards of organic pollutants. Organic removal techniques, including advanced oxidation processes, coagulation, sorption, microbial degradation, and membrane treatment are systematically reviewed. In particular, the influences of high salt on each technique are highlighted. Finally, different treatment techniques are evaluated in terms of energy consumption, cost, and organic removal efficiency. It is concluded that integrated coagulation-sorption-Fenton-membrane filtration represents a promising treatment process for FPW. This review provides valuable information for the feasible design, practical operation, and optimization of FPW treatment.

Elimination of pharmaceuticals from wastewater using microbial fuel cell-based bio-electro-Fenton process

This study highlights the potential of the microbial fuel cell (MFC)-based bio-electro-Fenton (BEF) process as an efficient and highly adaptable strategy for wastewater treatment. The research aims to optimize the pH of the cathodic chamber (3-7) and catalyst doses (Fe) (0-18.56%) on the graphite felt (GF) cathode, and examine the effect of operating parameters on chemical oxygen demand (COD) removal, mineralization efficiency, pharmaceuticals (ampicillin, diclofenac, and paracetamol) removal, and power generation. The study found that lower pH and higher catalyst dosage on the GF led to better performance of the MFC-BEF system. Under neutral pH, mineralization efficiency, paracetamol removal, and ampicillin removal were enhanced by 1.1 times, and power density improved by 1.25 times as catalyst dosage increased from 0 to 18.56%. Additionally, employing full factorial design (FFD) statistical optimization, the study identifies the optimized conditions for maximum COD removal, mineralization efficiency, and power generation, which are determined to be a pH of 3.82 and a catalyst dose of 18.56%.

Bibliometric analysis and literature review of ultrasound-assisted degradation of organic pollutants

Ultrasound as a clean, efficient, and cheap technique gains special attention in wastewater treatment. Ultrasound alone or coupled with hybrid processes have been widely studied for the treatment of pollutants in wastewater. Thus, it is essential to conduct a review about the research development and trends on this emerging technique. This work presents a bibliometric analysis of the topic associated with multiple tools such as Bibliometrix package, CiteSpace, and VOSviewer. The literature sources from 2000 to 2021 were collected from Web of Science database, and the data of 1781 documents were selected for bibliometric analysis in respect to publication trends, subject categories, journals, authors, institutions, as well as countries. Detailed analysis of keywords in respect to co-occurrence network, keyword clusters, and citation bursts was conducted to reveal the research hotspot and future directions. The development of the topic can be divided into three stages, and the rapid development begins from 2014. The leading subject category is Chemistry Multidisciplinary, followed by Environmental Sciences, Engineering Chemical, Engineering Environmental, Chemistry Physical, and Acoustics, and there exists difference in the publications of different categories. Ultrasonics Sonochemistry is the most productive journal (14.75 %). China is the leading country (30.26 %), followed by Iran (15.67 %) and India (12.35 %). The top 3 authors are Parag Gogate, Oualid Hamdaoui, and Masoud Salavati-Niasari. There exists close cooperation between countries and researchers. Analysis of highly cited papers and keywords gives a better understanding of the topic. Ultrasound can be employed to assist various processes such as Fenton-like process, electrochemical process, and photocatalysis for degradation of emerging organic pollutants for wastewater treatment. Research topics in this field evolve from typical studies on ultrasonic assisted degradation to latest studies on hybrid processes including photocatalysis for pollutants degradation. Additionally, ultrasound-assisted synthesis of nanocomposite photocatalysts receives increasing attention. The potential research directions include sonochemistry in pollutant removal, hydrodynamic cavitation, ultrasound-assisted Fenton or persulfate processes, electrochemical oxidation, and photocatalytic process.

Magnetic layered double hydroxide-based composites as sustainable adsorbent materials for water treatment applications: Progress, challenges, and outlook

Layered double hydroxides (LDHs) have shown exciting applications in water treatment because of their unique physicochemical properties, which include high surface areas, tunable chemical composition, large interlayer spaces, exchangeable content in interlayer galleries, and ease of modification with other materials. Interestingly, their surface, as well as the intercalated materials within the layers, play a role in the adsorption of the contaminants. The surface area of LDH materials can be further enhanced by calcination. The calcined LDHs can reattain their structural features upon hydration through the "memory effect" and may uptake anionic species within their interlayer galleries. Besides, LDH layers are positively charged within the aqueous media and can interact with specific contaminants through electrostatic interactions. LDHs can be synthesized using various methods, allowing the incorporation of other materials within the layers or forming composites that can selectively capture target pollutants. They have been combined with magnetic nanoparticles to improve their separation after adsorption and enhance adsorptive features in many cases. LDHs are relatively greener materials because they are mostly composed of inorganic salts. Magnetic LDH-based composites have been widely employed for the purification of water contaminated with heavy metals, dyes, anions, organics, pharmaceuticals, and oil. Such materials have shown interesting applications for removing contaminants from real matrices. Moreover, they can be easily regenerated and used for several adsorption-desorption cycles. Magnetic LDHs can be regarded as greener and sustainable because of several green aspects in their synthesis and reusability. We have critically reviewed their synthesis, applications, factors affecting their adsorption performance, and related mechanisms in this review. In the end, some challenges and perspectives are also discussed.

Challenges and Future Roadmaps in Heterogeneous Electro-Fenton Process for Wastewater Treatment

The efficiency of heterogeneous electro-Fenton technology on the degradation of recalcitrant organic pollutants in wastewater is glaringly obvious. This green technology can be effectively harnessed for addressing ever-increasing water-related challenges. Due to its outstanding performance, eco-friendliness, easy automation, and operability over a wide range of pH, it has garnered significant attention from different wastewater treatment research communities. This review paper briefly discusses the principal mechanism of the electro-Fenton process, the crucial properties of a highly efficient heterogeneous catalyst, the heterogeneous electro-Fenton system enabled with Fe-functionalized cathodic materials, and its essential operating parameters. Moreover, the authors comprehensively explored the major challenges that prevent the commercialization of the electro-Fenton process and propose future research pathways to countervail those disconcerting challenges. Synthesizing heterogeneous catalysts by application of advanced materials for maximizing their reusability and stability, the full realization of H₂O₂ activation mechanism, conduction of life-cycle assessment to explore environmental footprints and potential adverse effects of side-products, scale-up from lab-scale to industrial scale, and better reactor design, fabrication of electrodes with state-of-the-art technologies, using the electro-Fenton process for treatment of biological contaminants, application of different effective cells in the electro-Fenton process, hybridization of the electro-Fenton with other wastewater treatments technologies and full-scale analysis of economic costs are key recommendations which deserve considerable scholarly attention. Finally, it concludes that by implementing all the abovementioned gaps, the commercialization of electro-Fenton technology would be a realistic goal.

Evaluation of Dithiocarbamate-Modified Silica for Cisplatin Removal from Water

Despite the globally increasing use of platinum-based cytostatic drugs in the treatment of several types of cancer, only limited attention has been paid to developing a treatment for contaminated liquid samples originating from hospitals, laboratories and manufacturing facilities before and after their administration. In this work, we assess the efficiency of a low-cost adsorbent material, a dithiocarbamate-functionalized silica, in removing cisplatin from a solution containing it in the 0.5–150 mg L−1 concentration range. The advantage of having a surface-functionalized silica is that adsorption can occur by either non-covalent interaction or surface complexation. In the latter case platinum(II) is de-complexed and the original drug is no longer present. Adsorption occurs through a first rapid step, followed by a second slower process. This is likely due to the fact that in our operating conditions (0.9% w/v NaCl), only the original compound is present, for which ligand substitution is known to proceed slowly. The interesting performance, even at low metal concentration, and facile synthesis of the material mean it could be adapted for other applications where the recycling of platinum can be realized.

Advances in polymer-based detection of environmental ibuprofen in wastewater

Globally, ibuprofen is the third most consumed drug and its presence in the environment is a concern because little is known about its adverse effects on humans and aquatic life. Environmentalists have made monitoring and the detection of ibuprofen in biological and environmental matrices a priority. For the detection and monitoring of ibuprofen, sensors and biosensors have provided rapid analysis time, sensitivity, high-throughput screening, and real-time analysis. Researchers are increasingly seeking eco-friendly technology, and this has led to an interest in developing biodegradable, bioavailable, and non-toxic sensors, or biosensors. The integration of polymers into sensor systems has proven to significantly improve sensitivity, selectivity, and stability and minimize sample preparation using bioavailable and biodegradable polymers. This review provides a general overview of perspectives and trends of polymer-based sensors and biosensors for the detection of ibuprofen compared to non-polymer-based sensors.

Solar-light-driven LaFe x Ni1- x O3 perovskite oxides for photocatalytic Fenton-like reaction to degrade organic pollutants

LaFe _x Ni_{1- x} O₃ perovskite oxides were prepared by the sol-gel method under various conditions, including different pH values (pH 0 and pH 7) and different calcination temperatures (500-800 °C) as well as different Fe/Ni ratios (1/9, 3/7, 5/5, 7/3, 9/1). The samples were examined by XRD, DRS, BET, and SEM to reveal their crystallinity, light-absorption ability, specific surface area, and surface features, respectively. The photocatalytic Fenton reaction was conducted using various LaFe _x Ni_{1- x} O₃ perovskite oxides to decompose the methylene blue molecules. Accordingly, the synthesis condition of pH 0, calcination temperature at 700 °C, and Fe/Ni ratio = 7/3 could form LaFe_0.7Ni_0.3O₃ perovskite oxides as highly efficient photocatalysts. Moreover, various conditions during the photocatalytic degradation were verified, such as pH value, catalyst dosage, and the additional amount of H₂O₂. LaFe_0.7Ni_0.3O₃ perovskite oxides could operate efficiently under pH 3.5, catalyst dosage of 50 mg/150 mL, and H₂O₂ concentration of 133 ppm to decompose the MB dye in the 1st order kinetic rate constant of 0.0506 s^-1.

Application of perovskite oxides and their composites for degrading organic pollutants from wastewater using advanced oxidation processes: Review of the recent progress

In the recent years, perovskite oxides are gaining an increasing amount of attention owing to their unique traits such as tunable electronic structures, flexible composition, and eco-friendly properties. In contrast, their catalytic performance is not satisfactory, which hinders real wastewater remediation. To overcome this shortcoming, various strategies are developed to design new perovskite oxide-based materials to enhance their catalytic activities in advanced oxidation process (AOPs). This review article is to provide overview of basic principle and different methods of AOPs, while the strategies to design novel perovskite oxide-based composites for enhancing the catalytic activities in AOPs have been highlighted. Moreover, the recent progress of their synthesis and applications in wastewater remediation (pertaining to the period 2016-2022) was described, and the related mechanisms were thoroughly discussed. This review article helps scientists to have a clear outlook on the selection and design of new effective perovskite oxide-based materials for the application of AOPs. At the end of the review, perspective on the challenges and future research directions are discussed.

Efficient electrochemical removal of 5-fluorouracil pharmaceutical from wastewater by mixed metal oxides via anodic oxidation process

Nowadays, the entry of organic compounds into water resources is one of the leading global concerns due to the lack of water resources and rapid population growth. In this research, anodic oxidation (AO) method was used to remove 5-fluorouracil (5-FU) from aqueous solutions via Ni/RuO₂ and Ti/IrO₂-TiO₂-RuO₂ electrodes as cathode and anode, respectively. For this purpose, the characterization analysis of the electrodes, including X-ray diffraction, scanning electron microscopy, energy dispersive X-ray, and atomic force microscopy were performed. The electrochemical performance of the anode was investigated via cyclic voltammetry analysis. Then, the effect of operational variables, including applied current (mA), initial pH of the solution, initial 5-FU concentration (mg/L), and process time (min) on the 5-FU removal efficiency under the AO process was evaluated via artificial neural network (ANN) modeling. The results revealed that the maximum 5-FU removal efficiency was 96.96%. The applied current intensity, pH, initial 5-FU concentration, and process time were 300 mA, 5, 20 mg/L, and 140 min, respectively. Moreover, the investigation of 5-FU removal by-products and mineralization efficiency of the AO process was carried out via gas chromatography-mass spectrometry and total organic carbon analysis, respectively. The total organic carbon mineralization efficiency was 84.80% after 6 h of reaction time. The reusability and stability of the Ti/IrO₂-TiO₂-RuO₂ anode on 5-FU removal efficiency were measured and showed an approximately 5% decay in 5-FU removal efficiency after eight consecutive runs. The overall results and analysis confirmed this method is capable of removing 5-FU through Ti/IrO₂-TiO₂-RuO₂ anode and Ni/RuO₂ cathode from aqueous medium.

Light-Activated Hydroxyapatite Photocatalysts: New Environmentally-Friendly Materials to Mitigate Pollutants

This review focuses on a reasoned search for articles to treat contaminated water using hydroxyapatite (HAp)-based compounds. In addition, the fundamentals of heterogeneous photocatalysis were considered, combined with parameters that affect the pollutants’ degradation using hydroxyapatite-based photocatalyst design and strategies of this photocatalyst, and the challenges of and perspectives on the development of these materials. Many critical applications have been analyzed to degrade dyes, drugs, and pesticides using HAp-based photocatalysts. This systematic review highlights the recent state-of-the-art advances that enable new paths and good-quality preparations of HAp-derived photocatalysts for photocatalysis.

Two-Dimensional Nanostructures in the World of Advanced Oxidation Processes

Two-dimensional compounds with nanostructural features are attracting attention from researchers worldwide. Their multitude of applications in various fields and vast potential for future technology advancements are successively increasing the research progress. Wastewater treatment and preventing dangerous substances from entering the environment have become important aspects due to the increasing environmental awareness, and increasing consumer demands have resulted in the appearance of new, often nonbiodegradable compounds. In this review, we focus on using the most promising 2D materials, such as MXenes, Bi2WO6, and MOFs, as catalysts in the modification of the Fenton process to degrade nonbiodegradable compounds. We analyze the efficiency of the process, its toxicity, previous environmental applications, and the stability and reusability of the catalyst. We also discuss the catalyst’s mechanisms of action. Collectively, this work provides insight into the possibility of implementing 2D material-based catalysts for industrial and urban wastewater treatment.

Highly Selective Removal of Cationic Dyes from Wastewater by MgO Nanorods

The organic synthetic dyes employed in industries are carcinogenic and harmful. Dyes must be removed from wastewater to limit or eliminate their presence before dumping into the natural environment. The current study aims to investigate the use of MgO nanoparticles to eliminate basic fuchsine (BF), as a model cationic dye pollutant, from wastewater. The MgO nanorods were synthesized through a coprecipitation method. The obtained nanocomposite was characterized using various techniques such as X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Brunauer–Emmett–Teller (BET), and FTIR spectroscopy. It was found that the variation of dye concentration and pH influenced the removal of BF by MgO. The adsorption capacity of 493.90 mg/g is achieved under optimum operating conditions (pH = 11, contact time = 236 min, and initial BF concentration = 200 ppm). Pseudo-second-order adsorption kinetics and Freundlich isotherm models best fitted BF sorption onto MgO nanorods. The BF sorption mechanism is associated with the electrostatic attractions and hydrogen bond between the O–H group of MgO and the NH₂ groups of BF, as indicated by the pH, isotherms, and FTIR studies. The reusability study indicates that MgO was effectively used to eliminate BF in at least four continuous cycles. The investigation of MgO with different dyes suggests the high adsorption selectivity of BF, crystal violet (CV), and malachite green (MG) dyes compared with methyl orange (MO) dye. Overall, MgO nanorods can act as a potential and promising adsorbent for the efficient and rapid removal of cationic dyes (CV, MG, and BF) from wastewater.

Heterogeneous Advanced Oxidation Processes: Current Approaches for Wastewater Treatment

Nowadays, water pollution is one of the most dangerous environmental problems in the world. The presence of the so-called emerging pollutants in the different water bodies, impossible to eliminate through conventional biological and physical treatments used in wastewater treatment plants due to their persistent and recalcitrant nature, means that pollution continues growing throughout the world. The presence of these emerging pollutants involves serious risks to human and animal health for aquatic and terrestrial organisms. Therefore, in recent years, advanced oxidation processes (AOPs) have been postulated as a viable, innovative and efficient technology for the elimination of these types of compounds from water bodies. The oxidation/reduction reactions triggered in most of these processes require a suitable catalyst. The most recent research focuses on the use and development of different types of heterogeneous catalysts, which are capable of overcoming some of the operational limitations of homogeneous processes such as the generation of metallic sludge, difficult separation of treated water and narrow working pH. This review details the current advances in the field of heterogeneous AOPs, Fenton processes and photocatalysts for the removal of different types of emerging pollutants.

Recent Advances in Endocrine Disrupting Compounds Degradation through Metal Oxide-Based Nanomaterials

Endocrine Disrupting Compounds (EDCs) comprise a class of natural or synthetic molecules and groups of substances which are considered as emerging contaminants due to their toxicity and danger for the ecosystems, including human health. Nowadays, the presence of EDCs in water and wastewater has become a global problem, which is challenging the scientific community to address the development and application of effective strategies for their removal from the environment. Particularly, catalytic and photocatalytic degradation processes employing nanostructured materials based on metal oxides, mainly acting through the generation of reactive oxygen species, are widely explored to eradicate EDCs from water. In this review, we report the recent advances described by the major publications in recent years and focused on the degradation processes of several classes of EDCs, such as plastic components and additives, agricultural chemicals, pharmaceuticals, and personal care products, which were realized by using novel metal oxide-based nanomaterials. A variety of doped, hybrid, composite and heterostructured semiconductors were reported, whose performances are influenced by their chemical, structural as well as morphological features. Along with photocatalysis, alternative heterogeneous advanced oxidation processes are in development, and their combination may be a promising way toward industrial scale application.

Removal of pharmaceuticals from water using sewage sludge-derived biochar: A review

In recent years, considerable attention has been paid to the beneficial utilization of sewage sludge to reduce the risks associated with sludge disposal. Besides other applications of sludge, biochar produced from sludge has also been employed for the elimination of various pollutants from water. This review critically evaluates the recent progress in applications of sludge-based biochar for the adsorption of pharmaceuticals from water. The synthesis techniques of biochar production from sludge and their effects on physicochemical characteristics of produced biochar are discussed. The removal of various pharmaceuticals by sludge-based biochar are described in detail, with the emphasis on the adsorption mechanism and their reusability potential. It is evident from the literature that sludge-based biochar has demonstrated excellent potential for the adsorption of numerous pharmaceuticals from the aqueous phase. The major hurdles and issues related to the synthesis of sludge-based biochar and applications are highlighted, with reference to the adsorption of pharmaceuticals. Finally, a roadmap is suggested along with future research directions to ensure the sustainable production of biochar from sludge and its applications in water treatment.

Cephalexin removal by a novel Cu-Zn bionanocomposite biosynthesized in secondary metabolic products of Aspergillus arenarioides EAN603 with pumpkin peels medium: Optimization, kinetic and artificial neural network models

The present study aimed to investigate the removal efficiency of cephalexin (CFX) by a novel Cu-Zn bionanocomposite biosynthesized in the secondary metabolic products of Aspergillus arenarioides EAN603 with pumpkin peels medium (CZ-BNC-APP). The optimization study was performed based on CFX concentrations (1, 10.5 and 20 ppm); CZ-BNC-APP dosage (10, 55 and 100 mg/L); time (10, 55 and 100 min), temperature (20, 32.5 and 45 °C). The artificial neural network (ANN) model was used to understand the CFX behavior for the factors affecting removal process. The CZ-BNC-APP showed an irregular shape with porous structure and size between 20 and 80 nm. The FTIR detected CC, C-O and OH groups. ANN model revealed that CZ-BNC-APP dosage exhibited the vital role in the removal process, while the removal process having a thermodynamic nature. The CFX removal was optimized with 12.41 ppm CFX, 60.60 mg/L of CZ-BNC-APP, after 97.55 min and at 35 °C, the real maximum removal was 95.53% with 100.52 mg g^-1 of the maximum adsorption capacity and 99.5% of the coefficient. The adsorption of CFX on CZ-BNC-APP was fitted with pseudo-second-order model and both Langmuir and Freundlich isotherms models. These findings revealed that CZ-BNC-APP exhibited high potential to remove CFX.

Sustainable approaches for removal of cephalexin antibiotic from non-clinical environments: A critical review

In this article, the removal of cephalexin (CFX) antibiotic from non-clinical environment is reviewed. Adsorption and photocatalytic degradation techniques are widely used to remove CFX from waters and wastewaters, the combination of these methods is becoming more common for CFX removal. The treatment methods of CFX has not been reviewed before, the present article aim is to organize the scattered available information regarding sustainable approaches for CFX removal from non-clinical environment. These include adsorption by nanoparticles, bacterial biomass, biodegradation by bacterial enzymes and the photocatalysis using different catalysts and Photo-Fenton photocatalysis. The metal-organic frameworks (MOFs) appeared to have high potential for CFX degradation. It is evident from the recently papers reviewed that the effective methods could be used in place of commercial activated carbon. The widespread uses of photocatalytic degradation for CFX remediation are strongly recommended due to their engineering applicability, technical feasibility, and high effectiveness. The adsorption capacity of the CFX is ranging from 7 mg CFX g^-1 of activated carbon nanoparticles to 1667 mg CFX g^-1 of Nano-zero-valent iron from Nettle. In contrast, the photo-degradation was 45% using Photo-Fenton while has increased to 100% using heterogeneous photoelectro-Fenton (HPEF) with UVA light using chalcopyrite catalyst.

Effective treatment of hospital wastewater with high-concentration diclofenac and ibuprofen using a promising technology based on degradation reaction catalyzed by Fe0 under microwave irradiation

Real hospital wastewater was effectively treated by a promising technology based on degradation reaction catalyzed by Fe⁰ under microwave irradiation in this work. Fe⁰ powders were synthesized and characterized by different techniques, resulting in a single-phase sample with spherical particles. Optimum experimental conditions were determined by a central composite rotatable design combined with a response surface methodology, resulting in 96.8% of chemical oxygen demand reduction and 100% organic carbon removal, after applying MW power of 780 W and Fe⁰ dosage of 0.36 g L^-1 for 60 min. Amongst the several organic compounds identified in the wastewater sample, diclofenac and ibuprofen were present in higher concentrations; therefore, they were set as target pollutants. Both compounds were completely degraded in 35 min of reaction time. Their plausible degradation pathways were investigated and proposed. Overall, the method developed in this work effectively removed high concentrations of pharmaceuticals in hospital wastewater.

Perovskite Zinc Titanate Photocatalysts Synthesized by the Sol–Gel Method and Their Application in the Photocatalytic Degradation of Emerging Contaminants

In this study, perovskite ZnTiO3 photocatalysts were fabricated by the sol–gel method. The photocatalytic capability was verified by the degradation of the emerging contaminant, the antibiotic amoxicillin (AMX). For the preparation, the parameters of the calcination temperature and the additional amount of polyvinylpyrrolidone (PVP) and ammonia are discussed, including the calcining temperature (500, 600, 700, 800 °C), the volume of ammonia (750, 1500, 3000 μL), and the weight of PVP (3 g and 5 g). The prepared perovskite ZnTiO3 was characterized by XRD, FESEM, BET, and UV-Vis. It is shown that the perovskite ZnTiO3 photocatalysts are structurally rod-like and ultraviolet light-responsive. Consequently, the synthesis conditions for fabricating the perovskite ZnTiO3 photocatalysts with the highest photocatalytic performance were a calcining temperature of 700 °C, an additional ammonia amount of 1500 μL, and added PVP of 5 g. Moreover, the photocatalytic degradation of perovskite ZnTiO3 photocatalysts on other pollutants, including the antibiotic tetracycline (TC), methyl orange (MO), and methylene blue (MB) dyes, was also examined. This provides the basis for the application of perovskite ZnTiO3 as a photocatalyst to decompose emerging contaminants and organic pollutants in wastewater treatment.

Visible-Light-Driven Bio-Templated Magnetic Copper Oxide Composite for Heterogeneous Photo-Fenton Degradation of Tetracycline

The development of a visible-light-driven, reusable, and long-lasting catalyst for the heterogeneous photo-Fenton process is critical for practical application in the treatment of contaminated water. This study focuses on synthesizing a visible-light-driven heterogenous bio-templated magnetic copper oxide composite (Fe3O4/CuO/C) by a two-step process of bio-templating and hydrothermal processes. The prepared composite was characterized by field emission-scanning electron microscope (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), electrical impedance spectroscopy (EIS), and vibrating sample magnetometer (VSM). The results reveal that the prepared composite retains the template’s (corn stalk’s) original porous morphology, and a substantial amount of CuO and Fe3O4 particles are loaded onto the surface of the template. The prepared Fe3O4/CuO/C composite was employed as a catalyst for heterogeneous photo-Fenton degradation of tetracycline (TC) irradiated by visible light. The prepared Fe3O4/CuO/C catalyst has high efficiency towards TC degradation within 60 min across a wide pH range irradiated by visible light, which is attributed to its readily available interfacial boundaries, which significantly improves the movement of photoexcited electrons across various components of the prepared composite. The influence of other parameters such as initial H2O2 concentration, initial concentration of TC, and catalyst dosages was also studied. In addition to high efficiency, the prepared catalyst’s performance was sustained after five cycles, and its recovery is aided by the use of an external magnetic field. This research paper highlights the development of a heterogeneous catalyst for the elimination of refractory organic compounds in wastewater.

Comparative overview of advanced oxidation processes and biological approaches for the removal pharmaceuticals

Nowadays, pharmaceuticals are the center of significant environmental research due to their complex and highly stable bioactivity, increasing concentration in the water streams and high persistence in aquatic environments. Conventional wastewater treatment techniques are generally inadequate to remove these pollutants. Aiming to tackle this issue effectively, various methods have been developed and investigated on the light of chemical, physical and biological procedures. Increasing attention has recently been paid to the advanced oxidation processes (AOPs) as efficient methods for the complete mineralization of pharmaceuticals. Their high operating costs compared to other processes, however, remain a challenge. Hence, this review summarizes the current and state of art related to AOPs, biological treatment and their effective exploitation for the degradation of various pharmaceuticals and other emerging molecules present in wastewater. The review covers the last decade with a particular focus on the previous five years. It is further envisioned that this review of advanced oxidation methods and biological treatments, discussed herein, will help readers to better understand the mechanisms and limitations of these methods for the removal of pharmaceuticals from the environment. In addition, we compared AOPs and biological treatments for the disposal of pharmaceuticals from the point of view of cost, effectiveness, and popularity of their use. The exploitation of coupling AOPs and biological procedures for the degradation of pharmaceuticals in wastewater was also presented. It is worthy of note that an integrated AOPs/biological system is essential to reach the complete degradation of pharmaceuticals; other advantages of this hybrid technique involve low energy cost, an efficient degradation process and generation of non-toxic by-products.

Robust magnetic ZnO-Fe2O3 Z-scheme hetereojunctions with in-built metal-redox for high performance photo-degradation of sulfamethoxazole and electrochemical dopamine detection

This work reports synthesis of a dual-function facile heterojunction and investigation of role of the charge transfer dynamism between individual semiconductor components for superior photocatalytic and electrochemical sensing application. The bio-benevolent and sturdy ZnO/Fe₂O₃ heterojunctions were utilized for visible light facilitated photo-degradation of sulfamethoxazole (SMX) antibiotic and electrochemical sensing of dopamine drug (DA). The fabricated heterojunction were characterized for structural, optical, and magnetic properties. Structural studies revealed the formation of nano heterojunction containing both phases. Magnetic studies confirmed the highly pure magnetic nature of photocatalysts. ZnO/30 wt%Fe₂O₃ heterojunction (S2) shows 95.2% SMX degradation under visible light and high retention of performance under solar light. The scavenging experiments infer that OH radicals are the active species responsible for degradation. A Z-scheme photocatalytic mechanism was predicted for higher performance with protection of high potential VB of ZnO and CB of Fe₂O₃ for high generation of reactive oxygen species. LC-MS was employed to predict a plausible degradation route. The sample modified glassy carbon electrodes (GCE) were used for electrochemical sensing of dopamine via cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The S2 junction exhibited 0.18 μM limit of detection with concentration range of 1 μM-50 μM. The stability test was successfully carried out at room temperature for 15 days. In addition, the S2 modified electrodes were spiked in real urine samples and good results were obtained. DPV reveals that S2 modified electrode is best sensor for dopamine sensing among all synthesized heterojunctions. The detection mechanism was also discussed in detail. The in-built metal redox i.e Zn²⁺/Zn⁺ and Fe³⁺/Fe²⁺ facilitate the Z-scheme transfer, improve the charge transfer capacity and reduce the recombination. This study is beneficial because it reports utilization of popular and well-tested semiconductor metal oxides to form heterojunctions with dual capabilities of environmental detoxification and cost-effective electrochemical detection of biomolecules.

Heterogeneous Electro-Fenton as “Green” Technology for Pharmaceutical Removal: A Review

The presence of pharmaceutical products in the water cycle may cause harmful effects such as morphological, metabolic and sex alterations in aquatic organisms and the selection/development of organisms resistant to antimicrobial agents. The compounds’ stability and persistent character hinder their elimination by conventional physico-chemical and biological treatments and thus, the development of new water purification technologies has drawn great attention from academic and industrial researchers. Recently, the electro-Fenton process has been demonstrated to be a viable alternative for the removal of these hazardous, recalcitrant compounds. This process occurs under the action of a suitable catalyst, with the majority of current scientific research focused on heterogeneous systems. A significant area of research centres working on the development of an appropriate catalyst able to overcome the operating limitations associated with the homogeneous process is concerned with the short service life and difficulty in the separation/recovery of the catalyst from polluted water. This review highlights a present trend in the use of different materials as electro-Fenton catalysts for pharmaceutical compound removal from aquatic environments. The main challenges facing these technologies revolve around the enhancement of performance, stability for long-term use, life-cycle analysis considerations and cost-effectiveness. Although treatment efficiency has improved significantly, ongoing research efforts need to deliver economic viability at a larger scale due to the high operating costs, primarily related to energy consumption.

Acetaminophen degradation by a synergistic peracetic acid/UVC-LED/Fe(II) advanced oxidation process: Kinetic assessment, process feasibility and mechanistic considerations

Application of peracetic acid (PAA) in Advanced Oxidation Processes (AOPs) has seen an increase in the last few years. In this study, PAA/UVC-LED/transition metal was used to degrade acetaminophen (ACT) in an aqueous solution. Amongst tested transition metals (Fe, Cu, Co, Mn, Ag), Fe(II) demonstrated the highest efficiency. The effect of pH, PAA dosage, initial concentration of ACT and Fe(II) concentration was investigated on ACT removal. More than 95% removal efficiency was obtained in 30 min employing pH = 5.0, PAA 4 mM and 0.5 mM Fe(II) (k_app = 0.0993 min^-1). Scavenging experiments highlighted the contribution of oxygen-centered radicals; however, the dominant mechanism is hydroxyl radical-induced, while the superoxide radicals had a negligible role. The effect of anions in water showed that carbonate, (dihydrogen) phosphate and nitrite ions had a strong inhibitory effect, while a neutral effect was observed by sulfate, nitrate and chloride ions. Seven intermediates of ACT oxidation were determined and the ACT degradation pathway by the PAA/UVC-LED/Fe(II) is presented. The efficacy of the PAA/UVC-LED/Fe(II) process was also verified for the degradation of other contaminants of emerging concern and disinfection of fecal indicator microorganisms in real matrix (secondary WW). In conclusion, the studied PAA/UVC-LED/Fe(II) process opens a new perspective as a promising application of advanced oxidation for the degradation of organic pollutants.

Fabrication of silver phosphate-ilmenite nanocomposites supported on glycol chitosan for visible light-driven degradation, and antimicrobial activities

Recently, photo-degradation process under ultraviolet-light irradiation is being used as a substantial treatment method for the removal of environmental pollution. In this study, a silver phosphate-ilmenite (Ag₃PO₄-FeTiO₃) hetero structure supported on glycol chitosan catalyst was completely prepared, also, and its structural, and optical properties were characterized. Meantime, scanning electron microscopy, X-ray diffraction, X-ray photoelectron, and UV-vis spectra were applied. The Ag₃PO₄-FeTiO₃/glycol chitosan catalyst was used to degrade metronidazole under visible-light irradiation. The degradation rate of metronidazole in 25 min by Ag₃PO₄-FeTiO₃/glycol chitosan nanocomposites was found to be 99.2% under UV light irradiation, which was higher than that by Ag₃PO₄-FeTiO₃ (72.24%) and FeTiO₃ (35.5%), respectively. The active species trapping test of Ag₃PO₄-FeTiO₃/glycol chitosan indicated that ·OH and ·O₂^- participated during the reaction. The diffusion method was evaluated to appraise the bactericidal activity of the synthesized nanomaterials when tested against both Staphylococcus aureus and Escherichia coli bacteria, with or without LED-light irradiation. The antibacterial tests show higher inhibition zones under light illumination as compared to dark conditions. The antifungal properties of the prepared nanomaterials were analyzed by fungi (Aspergillus niger, and Fusarium solani) using disc diffusion analysis. It was confirmed that the prepared nanomaterials have the best antifungal agent as compared to the standard antibiotics. When the Ag₃PO₄-FeTiO₃/glycol chitosan was used, the amount of inhibition zone was enhanced.

Removal of emerging pollutants in aqueous phase by heterogeneous Fenton and photo-Fenton with Fe2O3-TiO2-clay heterostructures

Fe₂O₃-TiO₂-clay heterostructures have been prepared using an organo-bentonite as support, which organophilic character favored the fixation of TiO₂. Furthermore, Fe₂O₃ was successfully anchored by wet impregnation. The resulting materials are characterized by a disordered layered structure and a mesoporous texture. The heterostructures were employed as catalysts for the removal of two pharmaceuticals, acetaminophen (ACE) and antipyrine (ANT), by heterogeneous Fenton and photo-Fenton processes. ACE removal under different operation conditions was studied in detail to establish structure-performance relationships, being the TiO₂ formation and the developed texture the main factors controlling the activity. ANT showed a higher refractory behavior in oxidation by Fenton. Among the technologies studied, heterogeneous photo-Fenton achieved the best catalytic performance and higher kinetic rate and mineralization degree. Iron leaching was very low, lower than 5% of the initial iron load in all cases. This work demonstrates the potential application of these heterostructures for the removal of emerging pollutants of different nature.

Occurrence and distribution of priority pharmaceuticals in the Yellow River and the Huai River in Henan, China

The occurrence and spatial distribution of priority pharmaceuticals (PPs) in water samples from the Yellow River and the Huai River in the Henan region of China were investigated in this study. The concentration of the total PPs (ΣPPs; sum of the 10 observed PPs) ranged from not detected to 3474 ng L^-1 in samples from the Yellow River and from 4.35 to 146 ng L^-1 in samples from the Huai River. The level of the ΣPPs in the Huai River was much lower than that found in the Yellow River. The composition of the PPs differed between the two rivers. Norfloxacin, carbamazepine, and 5,5-diphenylhydantoin were detected at high concentrations in the Yellow River, whereas sulfamethazine, ampicillin trihydrate, carbamazepine, and 5,5-diphenylhydantoin were the dominant species in the Huai River, suggesting there were different pollution sources. In comparison to other studies around China, most of the PPs in water samples from the Yellow River and the Huai River were at low concentrations, except for norfloxacin and ofloxacin. There were significant seasonal variations among the PPs in water samples from the Huai River, whereas spatial distinctions were recorded among the PPs in the Yellow River. Dissolved organic carbon content did not correlate with the PPs in the studied area.