A ligand based innovative composite material for selective lead(II) capturing from wastewater

Evaluation of the quality grade of Congou black tea by the fusion of GC-E-Nose, E-tongue, and E-eye

In the present study, the comprehensive quality of Congou black tea (CBT) including aroma, taste, and liquid color was investigated by a combination of gas chromatography electronic nose (GC-E-Nose), electronic tongue (E-tongue), and electronic eye (E-eye). An excellent discrimination of different quality grades of CBT was accomplished through the fusion of GC-E-Nose, E-tongue, and E-eye combined with orthogonal partial least squares discriminant analysis, with parameters of R2Y = 0.803 and Q2 = 0.740. Moreover, the quantitative evaluation of CBT quality was successfully achieved by partial least squares regression analysis, with the absolute error within 1.39 point, and the relative error within 1.62%. Additionally, 12 key variables were screened out by stepwise multiple linear regression analysis, which significantly contributed to the comprehensive quality score of CBT. Our results suggest that the fusion of multiple intelligent sensory technologies offers great potential and practicability in the quality evaluation of black tea.

Utilization of peanut hull hydrochar /beta cyclodextrin/Fe3O4 magnetic composite for lead ion removal from water solution

This study involves synthesizing peanut hull hydrochar (PHH) and a PHH/β-CD/Fe3O4 magnetic composite through hydrothermal and chemical precipitation methods, respectively, to use as effective adsorbents for Pb2+ removal. Vibrating-sample magnetometry (VSM) and Brunauer-Emmett-Teller (BET) analyses revealed that the magnetic saturation value and specific active surface area of PHH/β-CD/Fe3O4 are 31.543 emu/g and 32.123 m2/g, respectively. The impact of key variables on adsorption efficiency was evaluated using the response surface method - central composite design. ANOVA results (F-value: 166.22 and p-value: <0.05) demonstrated that the model effectively assesses the interaction of variables in the adsorption process. Additionally, R2, Adjusted R2, and Predicted R2 values were 0.999, 0.986, and 0.975, respectively, indicating the model's high adequacy in describing response changes. The maximum efficiency for Pb2+ adsorption was found to be 95.35% using PHH and 99.73% with the PHH/β-CD/Fe3O4 magnetic composite. These measurements were taken at a temperature of 25 °C, an adsorbent dose of 1 g/L, a pH of 6, and a Pb2+ concentration of 5 mg/L, with respective contact times of 130 min and 50 min. Thermodynamic analysis revealed negative enthalpy and Gibbs free energy values, indicating that the adsorption process is exothermic and spontaneous. The negative entropy parameter suggests a reduction in random interactions during the process. The Pb2+ adsorption data for both PHH (R2: 0.982) and PHH/β-CD/Fe3O4 (R2: 0.985) were best described by the Pseudo 2nd order kinetic model. Equilibrium data followed the Freundlich model, with R2 values of 0.981 for PHH and 0.990 for PHH/β-CD/Fe3O4, highlighting the importance of heterogeneous surfaces in the removal process. The maximum adsorption capacities for Pb2+ were 26.72 mg/g for PHH and 33.88 mg/g for PHH/β-CD/Fe3O4. Reuse and stability tests confirmed the structural stability and reusability of the adsorbents. Therefore, the PHH/β-CD/Fe3O4 magnetic composite is a promising option for removing Pb2+ from aqueous solutions.

A novel green synthesis of MnO2-Coal composite for rapid removal of silver and lead from wastewater

The presence of Ag(I) and Pb(II) ions in wastewater poses a significant threat to human health in contemporary times. This study aims to explore the development of a novel and economical adsorbent by grafting MnO2 particles onto low-rank coal, providing an innovative solution for the remediation of water contaminated with silver and lead. The synthesized nanocomposites, referred to as MnO2-Coal, underwent thorough characterization using FTIR, XRD, BET, and SEM to highlight the feasibility of in-situ surface modification of coal with MnO2 nanoparticles. The adsorption of Ag(I) and Pb(II) from their respective aqueous solution onto MnO2-Coal was systematically investigated, with optimization of key parameters such as pH, temperature, initial concentration, contact time, ionic strength, and competing ions. Remarkably adsorption equilibrium was achieved within a 10 min, resulting in impressive removal rates of 80-90 % for both Ag(I) and Pb(II) at pH 6. The experimental data were evaluated using Langmuir, Freundlich, and Temkin isotherm models. The Langmuir isotherm model proved to be more accurate in representing the adsorption of Ag(I) and Pb(II) ions onto MnO2-Coal, exhibiting high regression coefficients (R2 = 0.99) and maximum adsorption capacities of 93.57 and 61.98 mg/g, along with partition coefficients of 4.53 and 71.92 L/g for Ag(I) and Pb(II), respectively, at 293 K. Kinetic assessments employing PFO, PSO, Elovich, and IPD models indicated that the PFO and PSO models were most suitable for adsorption mechanism of Pb(II) and Ag(I) on MnO2-Coal composites, respectively. Moreover, thermodynamic evaluation revealed the spontaneous and endothermic adsorption process for Ag(I), while exothermic behavior for adsorption of Pb(II). Importantly, this approach not only demonstrates cost-effectiveness but also environmental friendliness in treating heavy metal-contamination in water. The research suggests the potential of MnO2-Coal composites as efficient and sustainable adsorbents for water purification applications.

Development of eco-friendly biofilms by utilizing microcrystalline cellulose extract from banana pseudo-stem

Banana pseudo-stem, often considered as an underutilized plant part was explored as a potential reinforced material to develop an eco-friendly biofilm for food packaging applications. In this study, Microcrystalline cellulose (MCC) was extracted from banana pseudo-stem by alkali and acid hydrolysis treatment. The extracted MCC was used as a reinforced material in different concentrated polyvinyl alcohol (PVA) matrix alone as well as both PVA and Carboxymethyl Cellulose (CMC) matrix to develop biofilm by solvent casting method. The synthesized MCC powder was characterized by scanning electron microscope to ensure its microcrystalline structure and to observe surface morphology. The biofilms composed of MCC, PVA, and CMC were assessed through Fourier-transform infrared spectroscopy (FTIR), mechanical properties, water content, solubility, swelling degree, moisture barrier property (Water Vapor Permeability - WVP), and light barrier property (Light Transmission and Transparency). The FTIR analysis showed the rich bonding between the materials of the biofilms. The film incorporating a combination of PVA, CMC, and MCC (S6) exhibited the highest tensile strength at 26.67 ± 0.152 MPa, making it particularly noteworthy for applications in food packaging. MCC incorporation increased the tensile strength. The WVP content of the films was observed low among the MCC-induced films which is parallel to other findings. The lowest WVP content was showed by 1% concentrated PVA with MCC (S4) (0.223 ± 0.020 10-9 g/Pahm). The WVP content of S6 film was also considerably low. MCC-incorporated films also acted as a good UV barrier. Transmittance of the MCC induced films at UV range were observed on average 38% (S2), 36% (S4) and 6% (S6) which were almost 6% lower than the control films. The S6 film demonstrated the lowest swelling capacity (1.42%) and water content, indicating a significantly low solubility of the film. The film formulated with mixing of PVA, CMC and MCC (S6) was ahead in terms of food packaging characteristics than other films. Also, the outcomes of this study point out that MCC can be a great natural resource for packaging applications and in that regard, banana pseudo-stem proves to be an excellent source for waste utilization.

Hollow-microsphere-integrated optofluidic immunochip for myocardial infarction biomarker microanalysis

This work developed an optofluidic immunochip that uses whispering gallery mode with fiber laser enhancement, for the rapid detection of a key biomarker cardiac troponin I for acute myocardial infarction (AMI). The immunochip adopted an innovative design, using perforated hollow glass microspheres (HGMS) as carriers, with antibodies immobilized on the inner surface of the HGMS, thereby achieving ultra-low sample consumption. The performance of the immunochip was improved by fiber laser, including spectral width compression to 0.019 nm, optical signal-to-noise ratio amplification to 63.17 dB, and an enhancement in the limit of detection to 5 pg/mL. Moreover, this immunochip can provide results within 15 min, making it highly suitable for early AMI risk management. Compared to the standard electrochemiluminescence detection method, although some differences exist in the results of the immunochip due to the principle of detection and differences in antibody affinity, its positive reference value can be calculated as 0.0754 ng/mL, with a successful recognition rate of 88% for positive patients. The immunosensor is integrated on a polydimethylsiloxane substrate, with a compact size suitable for use in point-of-care devices and AMI self-screening, as well as rapid disease screening and microanalysis of various biomarkers, offering new possibilities for applications in these fields.

Chromaticity sensor for discriminatory identification of aliphatic and aromatic primary amines based on conformational changes of polyacetylene

The design and construction of suitable sensors that can selectively recognize chemically similar substances such as aliphatic and aromatic amines remain challenging. In this work, we reported a poly(phenylacetylene) bearing two aldehyde pendants as the color indicator for discriminative identification of amines. Reversible Schiff-base reaction of the aldehyde group with the amine resulted in a conformational transition of the polyacetylene backbone from cis-cisoid to cis-transoid, which further achieved a colorimetric change. Thirteen aliphatic amines and aromatic amines had been studied. Compared with aromatic amines, aliphatic amines generally caused the polyene backbone to display perceivable colorimetric change. Steric and electronic effect played a significant role in the colorimetric response. In addition, external environment, including amine content, polymer concentration, and temperature, had influence on the sensitivity of this colorimetric indicator system. The amines-induced colorimetric variation was further demonstrated by the CIELAB color space. Moreover, the colorimetric sensor exhibited excellent reversibility and recyclability.

A nanobody based ultrasensitive electrochemical biosensor for the detection of soluble CTLA-4 -A candidate biomarker for cancer development and progression

A soluble isoform of cytotoxic T-lymphocyte-associated antigen 4 (CTLA-4) has been found in the serum of healthy individuals and alterations in its expression level have been linked with the development and progression of various cancers. Conventionally, soluble CTLA-4 (sCTLA-4) has been quantified by techniques such as ELISA, western blot, and flow cytometry, which however are time-consuming, highly expensive and require large sample volumes. Therefore, rapid, cost-effective and real-time monitoring of soluble CTLA-4 levels is much needed to facilitate timely diagnosis of a worsening disease and help patient selection for immunotherapeutic interventions in cancer. Here, for the first time, we report an ultrasensitive, highly selective electrochemical nanobody (NAb) based biosensor for the quantitative detection of soluble CTLA-4 employing poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and gold nanoparticles modified electrode with attomole sensitivity. Incorporating nanomaterials with conductive polymers enhances the sensitivity of the electrochemical biosensor, while the nanobody's stability, specificity and ease of production make it a suitable choice as a bioreceptor. The proposed NAb-based sensor can detect sCTLA-4 from pure recombinant protein in a wide concentration range of 100 ag mL-1- 500 μg mL-1, with a limit of detection of 1.19 ag mL-1 (+3σ of the blank signal). The sensor's relative standard deviation for reproducibility is less than 0.4% and has effective real sample analytics for cell culture supernatant with no significant difference with pure recombinant protein (p < 0.05). Our proposed nanobody based sensor exhibits stability for up to 2 weeks (<3% variation). Moreover, this nanobody-based sensor presents a future opportunity for quantitative, ultrasensitive, and economical biosensor development that can be adapted to monitor the immune landscape of cancer patients to provide a larger therapeutic window.

Bifunctional Cu(II)-containing PDA-PEI copolymer dots: Demonstration of a dual-mode platform for colorimetric-fluorescent detection of glyphosate in the environment

The reliable and accurate detection of glyphosate is urgently demanded because it is related to food and environmental safety. In this contribution, a PDA-PEI/Cu2+ complex that possesses peroxidase-mimetic activity and stimulus-responsive fluorescence was fabricated by coordinating Cu2+ with polydopamine-polyethyleneimine copolymer dots (PDA-PEI CPDs). With the introduction of Cu2+, the fluorescence intensity of PDA-PEI CPDs dropped sharply owing to the electron transfer effect. As a peroxidase-mimicking nanozyme, the PDA-PEI/Cu2+ complex owns catalytic capacity to oxidize the colorless 3,3',5,5'-tetramethylbenzidine (TMB) into blue oxTMB, leading a further fluorescence quenching by internal filtering effect by oxTMB. Once the glyphosate participated, the fluorescence signal of PDA-PEI CPDs is recovered significantly because of the formation of more stable Glyp-Cu2+ complexes, meanwhile the peroxidase-mimicking activity of PDA-PEI/Cu2+ complex could be strongly hindered. According to this principle, a novel and extremely convenient 'turn off' colorimetric and 'turn on' fluorescence sensing platform can be established for dual-mode detection of glyphosate. The favorable sensitivity and selectivity and were verified in the analysis of glyphosate in the environment through the marriage of dual-signal sensing platform. The detection limit of the dual-mode glyphosate sensing platform was 103.82 ng/mL for colorimetric assay and 16.87 ng/mL for fluorescent assay, respectively. Satisfactory recoveries in the range of 96.40%-104.66% were obtained, indicating the potential of this method for application in complicated real sample. Thereby, this strategy broadens the applications of polydopamine nanomaterials and holds a promising application in determination of pesticide residues.

Enhanced thyroxine removal from micro-polluted drinking water resources in a bio-electrochemical reactor amended with TiO2@GAC particles: Efficiency, mechanism and energy consumption

A three-dimensional bioelectrochemical system (3D-BES) with both electrocatalytic and biodegradation functions was designed and developed to enhance iodine-containing hormone removal from micro-polluted oligotrophic drinking water sources and to reduce energy consumption. Thyroxine (T4) removal efficiency was 99.0% in the 3D-BES amendment with TiO2@GAC as the particle electrodes, which was 20.5% higher than the total efficiency of single biodegradation (28.7%) plus electrochemical decomposition (49.8%). The high T4 removal efficiency was a result of biochemical synergistic degradation, enhancement of electron transfer and utilization, enrichment of functional microorganisms, and the expression of dehalogenation functional genes. The electron transfer was increased by 1.63 times in 3D-BES compared to the 2D-BES, which contributed to: (i) ∼17.8% enhancement of dehalogenation, (ii) 2.35 times enhancement of the attenuation rate, and (iii) 60% reduction in energy consumption. Moreover, the aggregation of microorganisms and the hydrophobic T4 onto TiO2@GAC shortened the transfer distance of matter and energy, which induced the degradation steps to be shortened and the toxic decay to be accelerated from T4 and its metabolites. These comprehensive functions also enhanced the 31.8% ATPase activity, 7.3% abundance of the functional reductive dehalogenation genera, and 52.3% dehalogenation genes expression for Pseudomonas, Ancylobacter, and Dehalogenimonas, which contributed to an increase in T4 removal. This work provides an environmental-friendly biochemical synergistic method for the detoxification of T4 polluted water.

Adsorption of phenol using adsorbent derived from Saccharum officinarum biomass: optimization, isotherms, kinetics, and thermodynamic study

The present research shows the application of Taguchi's design of experiment approach to optimize the process parameters for the removal of phenol onto surface of Saccharum officinarum biomass activated carbon (SBAC) from an aqueous solution to maximize adsorption capacity of SBAC. The effect of adsorption parameters viz. adsorbent dose (m), temperature (T), initial concentration (C0) and mixing time (t) on response characteristics i.e., adsorption capacity (qt) has been studied at three levels by using L9 orthogonal array (OA) which further analyzed by variance analysis (ANOVA) for adsorption data and signal/noise (S/N) ratio data by using 'larger the better' characteristics. Using ANOVA, the optimum parameters are found to be m = 2 g/L, C0 = 150 mg/L, T = 313 K and t = 90 min, resulting in a maximum adsorption capacity of 64.59 mg/g. Adopting ANOVA, the percentage contribution of each process parameter in descending order of sequence is adsorbent dose 59.97% > initial phenol concentration 31.70% > contact time 4.28% > temperature 4.04%. The phenol adsorption onto SBAC was best fitted with the pseudo-second-order kinetic model and follows the Radke-Prausnitz isotherm model. Thermodynamic parameters suggested a spontaneous, exothermic nature and the adsorption process approaches physisorption followed by chemisorption. Hence the application of Taguchi orthogonal array design is a cost-effective and time-efficient approach for carrying out experiments and optimizing procedures for adsorption of phenol and improve the adsorption capacity of SBAC.

Functional Materials for Water Restoration: A "Fish Cage" for Efficient Capture of Pb(II) Ions

In this work, a "fish cage" material for trapping Pb(II) ions has been successfully obtained, which is a novel clathrate functionalized metal-oganic framework (Cage-MOF) by introducing free adsorption sites (SO42-). The three-dimensional (3D) cage structure of Cage-MOF gives it a larger contact area and can capture "swimming fish" (Pb(II)) like a "fishing cage" in a water solution. This is the first high-efficiency adsorption material obtained by introducing free coordination groups. Cage-MOF not only has excellent water stability but also improves the selectivity and affinity for Pb(II) ions in water because of the presence of sulfate adsorption sites, and its adsorption capacity is as high as 806 mg/g. This work shows a novel and effective idea for the synthesis of water restoration materials.

Competitive adsorption characteristics of VOCs and water vapor by activated carbon prepared from Fe/N-doped pistachio shell

Various materials have been developed to capture volatile organic compounds (VOCs) to mitigate air pollution. However, sorbent materials with excellent resistance to water are rare. Here, several Fe/N-doped activated carbons (ACs) have been prepared to capture VOCs in humid environments. The ACs were analyzed by various characterization techniques, such as BET, SEM, XPS, XRD, FTIR, and Raman. The results showed that Fe/N doping resulted in the specific surface area of the ACs increasing by 500 to 1000 m2 g-1, the average pore size increasing to approximately 2 nm, improved mesoporous structure, higher graphitization, lower hydrophilicity, and polarity. The VOCs adsorption performance of the ACs was evaluated by static and dynamic adsorption experiments. The uptake of toluene and ethyl acetate by ACs was enhanced to 224 mg g-1 and 135 mg g-1, respectively. And ACs were able to maintain 70 to 80% VOCs adsorption capacity for VOCs at 80% relative humidity. Furthermore, the microscopic mechanisms were investigated by the grand canonical Monte Carlo method (GCMC). The highly graphitized structure and the N functional groups favored the VOC adsorption process and discouraged the adsorption of water vapor. This work affirmed the dominance of Fe/N-doped carbon, which will contribute to the evolution of water-resistant VOCs adsorbent materials.

Lanthanide bimetallic MOF-based fluorescent sensor for sensitive and visual detection of sulfamerazine and malachite

A lanthanide terbium/europium metal-organic framework (Tb_0.6Eu_0.4-MOF) was prepared by one-step solvothermal method at room temperature. A series of characterizations including scanning electron microscopy, powder X-ray diffraction spectra, Fourier transform infrared spectra and X-ray photoelectron spectroscopy were carried out to clarify the physical characteristics of the synthesized material. The data clarified that the prepared Tb_0.6Eu_0.4-MOF possessed rod-like morphology with a width of 1-2 μm, and had good crystal structure, good stability, response speed and excitation-independent emission feature. The bunchy Tb_0.6Eu_0.4-MOF was then used to construct fluorescent sensors for rapid identification of malachite green and sulfamerazine. It was revealed that the detection mechanism was inner filter effect. The effects of different parameters such as excitation wavelength and incubation times were investigated on the fluorescence analysis performance. The data clarified that the optimal excitation wavelength and incubation time was 240 nm and 3 min, respectively. The detection platform exhibited the high sensitivity and selectivity toward malachite green in the linear range of 2-180 μM and determined limit of detection was 1.12 μM. Besides, the proposed sensor allowed sensitive detection of sulfamerazine in the linear range of 2-140 μM with a low detection limit of 0.1 μM. Meaningfully, a smartphone application was designed to assist the proposed sensor to realize visual, intelligent and rapid detection of malachite green and sulfamerazine. Furthermore, the practical application of the proposed sensor has been also verified by high performance liquid chromatography, showing good accuracy, sensitivity and satisfactory recoveries. The results suggested that the Tb_0.6Eu_0.4-MOF-based ratiometric fluorescent sensor had the potential to become a promising technique for rapid detection of malachite green or sulfamerazine with smartphone application. Therefore, the prepared Tb_0.6Eu_0.4-MOF is one kind of efficient and cost-effective potential materials for developing fluorescent sensor for rapid, sensitive and selective detection of sulfamerazine and malachite.

Determination of chloramphenicol in food using nanomaterial-based electrochemical and optical sensors-A review

Chloramphenicol (CAP) is a widely used antibiotic for the treatment of sick animals owing to its potent action and low cost. However, the accumulation of CAP in the human body can cause irreversible aplastic anemia and hematopoietic toxicity. Accordingly, development of various analytical techniques for the rapid detection of CAP in animal products and the related processed foods is necessary. Among these analytical techniques, electrochemical and optical sensors offer many advantages for CAP detection, including high sensitivity, simple operation and fast analysis speed. In this review, we summarize recent application of carbon nanomaterials, metal nanoparticles, metal oxide nanoparticles and metal organic framework in the development of electrochemical and optical sensors for CAP detection (2010-2022). Based on the advantages and disadvantages of nanomaterials, electrochemical and optical sensors are summarized in this review. The preparation and synthesis of electrochemical and optical sensors and nanomaterials in the field of rapid detection are prospected.

Source or sink role of an urban lake for microplastics from Guangdong-Hong Kong-Macao greater bay area, China

Plastic production and consumption in China are larger than others in the world, and the challenge of microplastic pollution is widespread. With the development of urbanization in the Guangdong-Hong Kong-Macao Greater Bay Area, China, the environmental pollution of microplastics is becoming an increasingly prominent issue. Here, the spatial and temporal distribution characteristics, sources, and ecological risks of microplastics were analyzed in water from an urban lake, Xinghu Lake, as well as the contribution of rivers. Importantly, the roles of urban lakes for microplastics were demonstrated through the investigations of contributions and fluxes for microplastic in rivers. The results showed that the average abundances of microplastics in water of Xinghu Lake were 4.8 ± 2.2 and 10.1 ± 7.6 particles/m³ in wet and dry seasons, and the average contribution degree of the inflow rivers was 75%. The size of microplastics in water from Xinghu Lake and its tributaries was concentrated in the range of 200-1000 μm. In general, the average comprehensive potential ecological risk indexes of microplastics in water were 247 ± 120.6 and 273.1 ± 353.7 in wet and dry seasons, which the high ecological risks of them were found through the adjusted evaluation method. There were also mutual effects among microplastic abundance, the concentrations of total nitrogen and organic carbon. Finally, Xinghu Lake has been a sink for microplastics both in wet and dry seasons, and it would be a source of microplastics under the influence of extreme weather and anthropogenic factors.

Effective Adsorption and Removal of Doxorubicin from Aqueous Solutions Using Mesostructured Silica Nanospheres: Box-Behnken Design Optimization and Adsorption Performance Evaluation

The aim of this study is to evaluate the efficacy of mesoporous silica nanospheres as an adsorbent to remove doxorubicin (DOX) from aqueous solution. The surface and structural properties of mesoporous silica nanospheres were investigated using BET, SEM, XRD, TEM, ζ potential, and point of zero charge analysis. To optimize DOX removal from aqueous solution, a Box-Behnken surface statistical design (BBD) with four times factors, four levels, and response surface modeling (RSM) was used. A high amount of adsorptivity from DOX (804.84 mg/g) was successfully done under the following conditions: mesoporous silica nanospheres dose = 0.02 g/25 mL; pH = 6; shaking speed = 200 rpm; and adsorption time = 100 min. The study of isotherms demonstrated how well the Langmuir equation and the experimental data matched. According to thermodynamic characteristics, the adsorption of DOX on mesoporous silica nanospheres was endothermic and spontaneous. The increase in solution temperature also aided in the removal of DOX. The kinetic study showed that the model suited the pseudo-second-order. The suggested adsorption method could recycle mesoporous silica nanospheres five times, with a modest reduction in its ability for adsorption. The most important feature of our adsorbent is that it can be recycled five times without losing its efficiency.

Biosorption of cadmium from aqueous solution by combination of microorganisms and chitosan: response surface methodology for optimization of removal conditions

The food-grade adsorbents of Saccharomyces cerevisiae (10⁸ CFU/mL), Bifidobacterium longum (10⁸ CFU/mL) and chitosan (1%w/v) alone or in combination were used for biosorption of cadmium (Cd) from aqueous solution. Among the tested adsorbents, combination of B. longum and chitosan had the highest efficiency. Therefore, biosorption process with B. longum/chitosan as the most efficient biosorbent was optimized by variables of pH (3-6), temperature (4-37 °C), contact time (5-180 min) and Cd concentrations (0.01-5 mg/L) using RSM. Twenty-seven tests were carried out and the data fitted to the second-order polynomial models. Results revealed that 99.11% of Cd was reduced within 180 min at concentration of 2.5 mg/L, pH 6 and temperature of 20.5 °C that were considered as the optimal conditions for Cd removal. The trend of isotherm was more fitted to the Langmuir model and maximum biosorption capacity was obtained about 3.61 mg/g. The pseudo-second-order fitted the biosorption kinetics for Cd ions. The B. longum/chitosan biosorbent exhibited the high affinity to Cd ion in the presence of coexisting metal ions. It could remove 81.18% of Cd from simulated gastrointestinal tract. Thus, B. longum/chitosan can have good potential as an effective adsorbent for Cd biosorption from aqueous solutions and human body.

"Turn-on" fluorescent sensor for oleanolic acid based on o-phenyl-bridged bis-tetraphenylimidazole

Fluorescent sensors had been extensively applied on sensing various biomolecules effectively, but no fluorescent sensor for oleanolic acid was presented up to now. In this work, the first fluorescent sensor for oleanolic acid was designed and synthesized based on o-phenyl-bridged bis-tetraphenylimidazole (PTPI). PTPI was prepared by bridging two tetraphenylimidazole units and o-phenylenediamine via Schiff-base condensation in yield of 86%. PTPI showed high sensing selectivity for oleanolic acid among 26 biomolecules and ions. The blue fluorescence at 482 nm was enhanced by 4.5 times after sensing oleanolic acid in aqueous media. The fluorescence sensing ability of PTPI for oleanolic acid maintained stable in pH = 5-9. The detecting limitation was as low as 0.032 μM. The detecting mechanism was clarified as 1:1 binding stoichiometry by fluorescence Job's plot, mass spectrometry, ¹H nuclear magnetic resonance and fourier transform infrared spectroscopy. The detecting ability of PTPI for oleanolic acid was successfully used for paper test and real samples of grapes and Kuding tea with recoveries in the range of 96.0%-106.0%, indicating the good application potential for on-site detecting oleanolic acid in real samples of fruits and food.

Optimized preparation of gangue waste-based geopolymer adsorbent based on improved response surface methodology for Cd(II) removal from wastewater

Resource utilization of gangue solid waste has become an essential research direction for green development. This study prepared a novel gangue based geopolymer adsorbent (GPA) for the removal of Cd(II) from wastewater using pretreatment gangue (PG) as the main raw material. The ANOVA indicated that the obtained quadratic model of fitness function (R² > 0.99, P-value <0.0001) was significant and adequate, and the contribution of the three preparation conditions to the removal of Cd(II) was: calcination temperature > Na₂CO₃:PG ratio > water-glass solid content. The hybrid response surface method and gray wolf optimization (RSM-GWO) algorithm were adopted to acquire the optimum conditions: Na₂CO₃:PG ratio = 1.05, calcination temperature of 701 °C, solid content of water glass of 22.42%, and the removal efficiency of Cd(II) by GPA obtained under the optimized conditions (GPAC) was 97.84%. Adsorption kinetics, adsorption isotherms and characterization by XRD, FTIR, Zeta potential, FSEM-EDS and BET were utilized to investigate the adsorption mechanism of GPAC on Cd(II). The results showed that the adsorption of Cd(II) from GPAC was consistent with the pseudo-second-order model (R² = 0.9936) and the Langmuir model (R² = 0.9988), the adsorption was a monolayer adsorption process and the computed maximum Cd(II) adsorption (50.76 mg g^-1) was approximate to experimental results (51.47 mg g^-1). Moreover, the surface morphology of GPAC was rough and porous with a specific surface area (SSA) of 18.54 m² g^-1, which provided abundant active sites, and the internal kaolinite was destroyed to produce a zeolite-like structure where surface complexation and ion exchange with Cd(II) through hydroxyl (-OH) and oxygen-containing groups (-SiOH and -AlOH) were the main adsorption mechanisms. Thus, GPAC is a lucrative adsorbent material for effective Cd(II) wastewater treatment, complying with the "high value-added" usage of solid wastes and "waste to cure poison" green sustainable development direction.

Removal of Cd(II), Co(II), Cr(III), Ni(II), Pb(II) and Zn(II) ions from wastewater using polyethyleneimine (PEI) cryogels

The removal of the target analytes, Cd(II), Co(II), Cr(III), Ni(II), Pb(II), and Zn(II) from contaminated waters was achieved using super porous polyethyleneimine (PEI) cryogels as adsorbent. The optimum values of the sample pH and contact time were determined as 4.0 and 90 min, respectively, for the removal of the analytes. The adsorption capacities of the sorbent were between 19.88 and 24.39 mgg^-1 from 10 mL of 50 mgL^-1 target metal ion solutions. The sorption kinetics of metal ions were fitted with the pseudo-second-order model. The adsorption isotherms of the target analytes into PEI cryogel were well-fitted to the Langmuir isotherm model as expected from the material homogeneity. The selectivity of the PEI cryogel in the presence of Na⁺, Ca²⁺, Mg²⁺, NO₃^-, K⁺ and Cl^- ions even at high concentrations was tested, and the tolerance limits were satisfactory enough, e.g., the adsorption of the target analytes was even not affected in the presence of 2000 mgL^-1 Ca²⁺, K⁺, Na⁺, Cl^- and 5000 mgL^-1 NO₃^- ions. The PEI cryogels were successfully utilized in different industrial wastewater samples that were spiked with a known amount of analytes. The removal of the analytes from wastewater samples was in the following ranges 91.94-99.86% for Cd(II), 89.59-99.89% for Co(II), 80.35-99.76% for Cr(III), 92.02-99.84% for Ni(II), 83.28-99.86% for Pb(II), and 82.94-98.24% for Zn(II), respectively. The presented novel removal strategy offers a selective, efficient, and easy application for target metal ions from industrial wastewater samples.

Focus on the crucial deformation region to adjust the comprehensive performance of poly (L-lactic acid) stent

The fully biodegradable polymer stent is considered as the fourth-generation vascular implant with good biocompatibility and long-term therapeutic potential. It has attracted much attention because it overcomes the disadvantage of the permanently implanted metal stent. However, compared with the metal stent, its mechanical properties are slightly inferior, which is an urgent problem. Based on previous studies, fully biodegradable polymer stents are prone to experience cracks and damage in large deformation region during the crimping and expansion process. The large deformation region is mainly located at the ring bend of the stent. We supposed that these damages are the leading causes of weakening the mechanical performance of polymer stents and are mainly affected by the crucial deformation region. For this purpose, this work studies the relationship between different crucial deformation regions and the mechanical performance of the polymer stent. Firstly, the volume of the crucial deformation region is improved by increasing the ring width. Although the radial strength of the stent is enhanced with the increase in ring width, the radial stiffness also increases, and correspondingly, the flexibility of the stent decreases. To obtain acceptable comprehensive mechanical performance, two types of slotting design in critical deformation region were proposed. The proposed slotted stent with a bulge has sufficient radial strength and low radial stiffness, having a good radial support capacity and flexibility. In other words, the proposed stent has improved the radial support without sacrificing flexibility. Overall, different crucial deformation regions cause different degrees of damage to the stent during crimping and expansion, which affects the mechanical properties of the stent. Reasonable structural design of the crucial deformation region is the key to adjust the comprehensive performance of the stent.

Enhanced Adsorption and Evaluation of Tetracycline Removal in an Aquatic System by Modified Silica Nanotubes

In the present study, a nanocomposite adsorbent based on mesoporous silica nanotubes (MSNTs) loaded with 3-aminopropyltriethoxysilane (3-APTES@MSNTs) was synthesized. The nanocomposite was employed as an effective adsorbent for the adsorption of tetracycline (TC) antibiotics from aqueous media. It has an 848.80 mg/g maximal TC adsorption capability. The structure and properties of 3-APTES@MSNT nanoadsorbent were detected by TEM, XRD, SEM, FTIR, and N₂ adsorption-desorption isotherms. The later analysis suggested that the 3-APTES@MSNT nanoadsorbent has abundant surface functional groups, effective pore size distribution, a larger pore volume, and a relatively higher surface area. Furthermore, the influence of key adsorption parameters, including ambient temperature, ionic strength, initial TC concentration, contact time, initial pH, coexisting ions, and adsorbent dosage, had also been investigated. The 3-APTES@MSNT nanoadsorbent's ability to adsorb the TC molecules was found to be more compatible with Langmuir isothermal and pseudo-second-order kinetic models. Moreover, research on temperature profiles pointed to the process' endothermic character. In combination with the characterization findings, it was logically concluded that the 3-APTES@MSNT nanoadsorbent's primary adsorption processes involved interaction, electrostatic interaction, hydrogen bonding interaction, and the pore-fling effect. The synthesized 3-APTES@MSNT nanoadsorbent has an interestingly high recyclability of >84.6 percent up to the fifth cycle. The 3-APTES@MSNT nanoadsorbent, therefore, showed promise for TC removal and environmental cleanup.

Fabrication of chitosan-MnO2‑iridium/nanoceria supported nanoparticles: Catalytic and anti-radical activities

Chitosan capped MnO₂‑iridium nanoparticles supported on nanoceria (Ch-MnO₂-Ir/CeO₂) were fabricated by using combination of colloidal solution and metal displacement galvanic methods. The oxidative degradation of acid orange 7 in aqueous solution by activated persulfate with the as-prepared nanoparticles was studied. The resulting Ch-MnO₂-Ir/CeO₂ with S₂O₈^2-, 80 % degraded 70.06 mg/L of acid orange 7 within 100 min, while at the same time, Ch-Ir, Ch-MnO₂, and Ch-Ir-MnO₂ remained inactive. CeO₂ increased the surface of the catalyst, and also improved the reactive oxygen species site of Ch-Ir-MnO₂ through the activation of S₂O₈^2- with CeO₂. The reversible redox cycle reaction, Ce (III) ↔ Ce (IV) and strong synergistic effect of MnO₂-Ir are responsible for the remarkable catalytic performance of Ch-MnO₂-Ir/CeO₂/S₂O₈^2- system. The degradation of acid orange 7 could be significantly retarded with inorganic (NO₃^- < Cl^- < SO₄^2- < H₂PO₄^- < HCO₃^-) and organic scavengers (ethanol < tertiary butanol < benzoquinone < phenol). Ch-MnO₂-Ir/CeO₂ exhibited excellent stability and reusability. Anti-radical activity of chitosan and Ch-MnO₂-Ir/CeO₂ was evaluated with 2,2-diphenyl-1-picrylhydrazyl (DPPH) free radical. The free radical properties increase with concentration of chitosan and Ch-MnO₂-Ir/CeO₂.

Immunochromatographic Assay based on Sc-TCPP 3D MOF for the rapid detection of imidacloprid in food samples

In this work, a highly sensitive immunochromatographic test strip (ITS) based on Scandium-Tetrakis (4-carboxyphenyl) porphyrin (TCPP) metal-organic framework nanocubes (ScTMNs) was developed for ultrasensitive and facile visual determination of imidacloprid (IDP). TCPP as the porphyrin-based planar ligand and Sc³⁺ as the metal center were applied to form the ScTMNs via coordination chelation. Giving the credit to its excellent optical characteristics, strong affinity with monoclonal antibodies, and favorable biocompatibility, the ScTMNs was selected as a signal tag. Under optimized conditions, the ITS exhibited a great liner relationship in the range of 0.04-3 ng/mL and the detection limit was 0.04 ng/mL for the IDP detection. Additionally, IDP was successfully detected in tomatoes, millet, corn and carrot samples with satisfied recoveries. To the best of our knowledge, this is the first time that ScTMNs have been used in immunochromatography which are expected to have potential applications in detection of other substances.

Heavy metals reshaping the structure and function of phylloplane bacterial community of native plant Tamarix ramosissima from Pb/Cd/Cu/Zn smelting regions

Heavy metal (HM) is noxious element that cannot be biodegraded, thus accumulating in the environment and posing a serious threat to the ecology. Plant phylloplane harbors diverse microbial communities that profoundly influence ecosystem functioning and host health. With more HM accumulating around smelters, native plants and microbes in various habitats tend to suffer from HM. However, the response of phylloplane bacteria of native plants to HM remains unclear. Thus, this study aimed to explain the response of Tamarix ramosissima, a phylloplane bacterial community to HM as well as the effect of the process on host growth in situ by investigating the potential source of HM and bacterial community shift. Results showed that, in most cases, the contaminated site with high HM level caused more accumulation of HM in phylloplane and leaves. Moreover, HM in the phylloplane was not from the internal transport of the plant but it could be due to the wind action or rains. Bacteria in phylloplane may have come from the soil due to their strong positive correlation with corresponding soil at the genus level. High HM level inhibited the relative abundance of dominant bacteria, increased the diversity and species richness of bacterial community in phylloplane, and induced more special bacteria to maintain higher productivity of the host plant, for which, Cu and Pb were the major contributors. Meanwhile, bacteria in phylloplane showed a universal positive correlation in the co-occurrence network, which showed less stability than that in corresponding soil in the smelting region, and it is helpful to regulate the growth of plants more rapidly. Nearly 25% of KEGG pathways were modulated by high HM level and bacterial function tended to stabilize HM to avoid the potential process of leaf absorption. The study illustrated that HM in phylloplane played an important role in shaping the bacterial community of phylloplane as compared to HM in leaves or phyllosphere, and the resulting increase of diversity and richness of bacterial community and special bacteria further maintained the growth of the host plant suffering from HM stress.

Single-polymer dynamics of starch-like branched ring polymers in steady shear flow

The stretching dynamics and dynamical behaviors of individual branched ring polymer (BRP), a coarse-grained model for some types of the starch, in steady shear flow are studied by using a hybrid mesoscale simulation approach that combines multiparticle collision dynamics with standard molecular dynamics. By analyzing the stretched configuration of BRPs, we find the polymer size increases nonmonotonically with increasing branch length. Meanwhile, the decrease of the alignment angle of the stretched configuration of BRPs follows a universal power law during the first downward phase as the shear rate increases. Constructing the three-dimensional surface of the polymer's ring backbone and tracing the temporal fluctuations of the surface's normal vector along the simulation trajectory, the tumbling and tank-treading motion are clearly reflected by periodic and non-periodic changes of the normal vector. Interestingly, these temporal changes are much more regular than that of the gyration tensor. Thus, a novel cross-correlation function, which is the correlation between fluctuations of the normal vector along the flow direction and the velocity-gradient direction, is proposed to analyze the tumbling motion that usually coexists with the tank-treading motion. This function can naturally address the fails of traditional method that analyzing the tumbling motion by determining the correlation of temporal fluctuations of the gyration tensor G_αα. By analyzing the dynamical behaviors of BRPs, diverse dependences of the tumbling frequency ω_TB and tank-treading frequency ω_TT on the shear rate γ̇ are observed at a wide range of shear rates and polymer sizes. Furthermore, our simulations also reveal that the tank-treading motion is more stable than the tumbling motion for small-branch-size BRPs but the tumbling motion is more stable than the tank-treading motion for large-branch-size BRPs.

Divalent metal ion removal from simulated water using sustainable starch aerogels: Effect of crosslinking agent concentration and sorption conditions

This paper evaluates corn starch aerogels, studying different crosslinking agent (trisodium citrate) concentrations (1:1, 1:1.5, and 1:2) and sorption conditions (contact time, adsorbent weight, and initial concentration) regarding the potentially toxic elements (PTEs) [Cd(II) or Zn(II)] adsorption of the aqueous systems. Besides, other properties of aerogels, such as structural properties, specific surface area, and mechanical performance, were evaluated. For adsorption results, better values were observed in adsorption capacity and efficiency for the initial concentration of 100 ppm. In addition, an adsorption time of 12 h and an adsorbent weight of 3.0 g obtained better results due to the possible balance in this time and the high specific surface area available for Cd(II) adsorption. As for the type of adsorbent, the Aero 1:1.5 sample (intermediate crosslinking agent concentration) obtained better results, possibly due to the high porosity, smaller pore sizes, high pore density, and high specific surface area (198 m²·g^-1). In addition, hydroxyl groups in the starch aerogel removed Cd(II) ions with 30 % adsorption efficiency. Lastly, Aero 1:1.5 obtained a high mechanical strength at compression and a satisfactory compressive modulus. In contrast, starch aerogels did not absorb the Zn(II) ion.

A critical review on pineapple (Ananas comosus) wastes for water treatment, challenges and future prospects towards circular economy

Each year, nearly 30 million tons of pineapple fruit are harvested for food and drinking industries, along with the release of a huge amount of pineapple wastes. Without the proper treatment, pineapple wastes can cause adverse impacts on the environment, calling for new technologies to convert them into valuable products. Here, we review the production and application of adsorbents derived from pineapple wastes. The thermal processing or chemical modification improved the surface chemistry and porosity of these adsorbents. The specific surface areas of the pineapple wastes-based adsorbents were in range from 4.2 to at 522.9 m²·g^-1. Almost adsorption systems followed the pseudo second order kinetic model, and Langmuir isotherm model. The adsorption mechanism was found with the major role of electrostatic attraction, complexation, chelation, and ion exchange. The pineapple wastes based adsorbents could be easily regenerated. We suggest the potential of the pineapple wastes towards circular economy.

Removal performance and mechanisms of Pb(II) and Sb(V) from water by iron-doped phosphogypsum: single and coexisting systems

The serious environmental risks caused by Pb(II) and Sb(V) co-contamination increase the need for their efficient and simultaneous removal. In this study, the remediation feasibility by Fe-doped phosphogypsum (FPG) was elucidated for single systems with Pb or Sb pollutant and coexisting systems with both from water. As for single systems, Fe doping effectively enhanced the Pb(II) removal performance by phosphogypsum (PG) at low Pb(II) concentrations of below 100 mg/L via the combination of precipitation and complexation. The optimal removal rate of Sb(V) by FPG increased by 2.08-3.31 times as compared to that of by PG (10-120 mg/L), mainly due to the strong affinity of iron hydroxyl (≡Fe-O-H) towards Sb(V). Compared with the single systems, the coexistence greatly enhanced the Pb(II) and Sb(V) removal performance by FPG, and the interaction behavior between Pb(II) and Sb(V) on the FPG was concentration dependent. Briefly, the sorption of FPG controlled the elimination of low coexisting concentrations of Pb(II) and Sb(V), whereas the co-precipitation process between Pb(II) and Sb(V) predominated with high ions concentration. The significant synergistic effects were found during the removal of Pb(II) and Sb(V) on FPG in the coexisting system, which mainly attributed to precipitation, bridging complexation and electrostatic attraction. Considering the advantages such as facile preparation, low cost and high removal capacity, FPG is a promising material to uptake Pb(II) and/or Sb(V) from contaminated water.

Perspective on Fe0-PS synergetic effect and reaction mechanism in the thallium(I) contaminated water treatment

Due to extreme toxicity of the element of thallium (Tl), increasing aqueous Tl pollution incidents have aroused growing concerns. As the prevalent and stable form, i.e., monovalent Tl, the highly efficient removal methodologies of Tl(I) from (waste)water remains limited and challenging. In this study, an advanced oxidation method, the feasibility of using zero valent iron (Fe⁰) coupled with persulfate (PS) to treat Tl(I)-containing synthetic wastewater was investigated. Its influence parameters, including reaction time, initial Tl concentration, dosages of PS and Fe⁰, initial and coagulation pH, temperature, coexisting ions and organic matter (NO₃^-, SO₄^2-, Cl^- and HA) were examined. The results revealed that the system can be applied to a wide range of pH and temperature and the reaction equilibrium can be reached in about 30 min. Favorable Tl(I) removal rate (>98%) was observed in the synthetic wastewater with medium and relatively high Tl(I) concentration (≤0.250 mM). The analyses of characterization results including electron spin resonance spectrometer and X-ray photoelectron spectroscopy indicated that ·OH played a vital role in the removal of Tl(I), which was oxidized and removed by co-precipitation. Fe⁰ can be served as a stable source of Fe²⁺ to efficiently catalyze PS. The remaining Fe⁰ can be easily separated because of its magnetism, assuring the promising reusability of the reactant. The study aims to provide references for treatment of real Tl polluted wastewater.

Bioremediation of heavy metals from the aqueous environment using Artocarpus heterophyllus (jackfruit) seed as a novel biosorbent

Biosorption is an environment-friendly and economic technique to remediate heavy metals from aqueous systems. In the present study, Artocarpus heterophyllus seed powder was used as a biosorbent material to remove different heavy metals. The batch adsorption studies confirmed the higher removal percentage of the Artocarpus heterophyllus (jackfruit) seed powder for arsenic (As⁵⁺), cadmium (Cd²⁺), and chromium (Cr⁶⁺) while lower efficiency was observed for other heavy metals like copper (Cu²⁺), zinc (Zn²⁺) and nickel (Ni²⁺). Optimization of different process parameters was carried out and the optimum conditions were: adsorbent weight of 0.5 g for the initial concentration of heavy metals as 40 μg/L, 30 mg/L, and 30 mg/L; contact time of 10 h, 8 h, and 6 h; process temperature from 25 to 30 °C; pH of 7, 7.5, and 7.5 for As⁵⁺, Cd²⁺, and Cr⁶⁺ respectively. The SEM-EDX, FTIR, and XRD studies before and after adsorption of heavy metals resulted in affirmative observations. The equilibrium data of the study was well fitted for Langmuir isotherm for As⁵⁺, Cd²⁺, and Cr⁶⁺, Freundlich for As⁵⁺and Cr⁶⁺, Dubinin-Radushkevich for Cd²⁺and Cr⁶⁺. The kinetic and thermodynamic study confirmed that the adsorption of all three heavy metals was following the pseudo-second-order kinetics with the endothermic and spontaneous process respectively. The cost analysis of the process confirmed that the whole process was cost-effective compared to other processes. Hence the Artocarpus heterophyllus seed powder was verified for its high heavy metal remediation efficiency from aqueous environments along with the added advantages of being eco-friendly and economic compared to other alternatives.

Natural kaolinite-based hierarchical porous microspheres as effective and highly recyclable adsorbent for removal of cationic dyes

The development of efficient, recyclable, and environment-friendly adsorbent for wastewater remediation is considered a challenge. In this study, a hierarchical porous kaolinite microsphere (HPKS) with three-dimensional (3D) structure was fabricated based on natural-layered kaolinite mineral via an environmentally friendly direct hydrothermal strategy. Characterization results revealed that HPKS microsphere with 3D hierarchical porous structure was constructed with numerous nanospheres which are assembled by ultrafine aluminosilicate flakes. HPKS exhibited negative charge feature ranging from strong acid to high alkaline solution. The influence of contact time, solution pH, initial dye concentration, adsorbent dosage, and foreign ions on methylene blue (MB) adsorption capability was systematically investigated. The synthesized HPKS with higher specific surface area (250.6 m²/g) shows an outstanding adsorption capacity towards MB (411.8 mg/g) and excellent selectivity for cationic MB dyes over anionic methyl orange and competitive metal ions. The adsorption kinetic experiment results fit very well with the pseudo-second-order model and reflect the fast adsorption rate of MB on HPKS. The sorption isotherm study reveals the chemisorption of electrostatic attraction between the cationic MB molecules and the negative charged surfaces of HPKS. More importantly, the MB removal efficiency is more than 99% in a broad range of solution pH value. The adsorption capacities of HPKS can be easily recovered by calcination at 600 °C to remove the adsorbed dyes and without obvious diminishment even after six successive cycles. Therefore, the HPKS is a cost-effective and environmentally friendly adsorbent which has is promising to use in practical applications.

A novel nanofibrous PAN ultrafiltration membrane embedded with ZIF-8 nanoparticles for effective removal of Congo red, Pb(II), and Cu(II) in industrial wastewater treatment

A novel Polyacrylonitrile (PAN) composite membrane involving ZIF-8 nanoparticles, named as ZIF-8/PAN membrane, was obtained via electrospinning to remove the Congo red (CR), Pb(II) and Cu(II) ions in industrial wastewaters, during which the adsorption mechanisms were examined in this study. The adsorption efficiency of the electrospun ZIF-8/PAN membrane was as high as 89%, 92% and 76% for CR, Pb(II) and Cu(II), respectively. Comparative analysis showed that ZIF-8 nanoparticles embedded in the ZIF-8/PAN membrane accounted for these enhanced adsorption capabilities. The adsorption behaviors of the ZIF-8 nanoparticles were investigated through experiments and theoretical analysis, and the results unraveled that the adsorption for CR by the ZIF-8 was mainly including electrostatic interaction, hydrogen bonding and π-π interaction, while those for Pb(II) and Cu(II) were mainly caused by ion-exchange and chemical adsorption. Parametric studies were conducted to optimize the conditions for removing CR, Pb(II), and Cu(II) by ZIF-8 nanoparticles, during which all of pollutants showed different reactions to the solution pH. This work not only develops a novel ZIF-8/PAN composite membrane for effective removals of pollutants, but also reveals the underlying mechanisms of pollutants adsorption in terms of molecular interactions, providing important understandings on fibrous materials design for efficient heavy metals and dyes removals in industrial wastewater treatment.

Auto-fluorescence of cellulose paper with spatial solid phrase dispersion-induced fluorescence enhancement behavior for three heavy metal ions detection

Auto-fluorescence of cellulose paper is often considered as an interfering fluorescence, which directly impedes the cellulose paper as a substrate material. This paper creatively explored the composition and properties of auto-fluorescence, and lignosulfonate was primarily speculated as the main source of auto-fluorescence. Surprisingly, its spatial solid phrase dispersion-induced fluorescence enhancement behavior was found. Then, cellulose paper was modified with Mn-doped ZnS quantum dots, and the prepared ratiometric fluorescent paper chip has good performances on morphology, stability, and fluorescence properties. Besides, the paper chip exhibited different fluorescence responses to three heavy metal ions in water sample. The limit of detection for Cd²⁺, Hg²⁺ and Pb²⁺ reached 1.61 nM, 0.01 nM, and 0.02 nM, respectively. In short, the molecular simulation results theoretically proved that heavy metal ions owned substitution affinity with lignosulfonate. Ultimately, this study was the first attempt to utilize paper-based auto-fluorescence, which could better accelerate the development of paper-based chips.

Construction of metal-organic framework/polymer beads for efficient lead ions removal from water: Experiment studies and full-scale performance prediction

Metal-organic frameworks (MOFs) show great promise in heavy metal removal; however, their applications are restricted by the poor separability and water instability. Herein, granular Zr-based MOF-polymer composite beads (MPCB(Zr)) (mean diameter ∼ 1.74 mm) were synthesized using a facile dropping method, and applied on efficient lead ions (Pb(II)) removal. The as-prepared MPCB(Zr) demonstrated deep Pb(II) removal capability by reducing its concentration to ∼ 0.002 mg L^-1 after adsorption equilibrium at 360 min. The distribution coefficient for Pb(II) reached 8.0 × 10⁶ mL g^-1, and the theoretical adsorption capacity for Pb(II) was 144.5 mg g^-1 (0.70 mmol g^-1, 30 °C). The resulting MPCB(Zr) was highly selective for Pb(II), with the selectivity coefficient up to ∼ 1.0-3.6 × 10³ for the background cations (Na(I), K(I), Ca(II), and Mg(II)). Moreover, the MPCB(Zr) exhibited a broad working pH range (3.0-6.0) and satisfactory anti-interference to dissolved organic matters (humic acid and fuvic acid). Notably, the MPCB(Zr) also demonstrated excellent reusability with the Pb(II) removal efficiency over 99.0% after 20 cycles. Combined physicochemical characterizations unveiled that the thiol and oxygen-containing groups (e.g., hydroxyl, carboxylate) were responsible for the effective Pb(II) removal. To provide guidance for engineering application, the full-scale performance of the MPCB(Zr) under varying operation conditions was systematically evaluated via the validated pore surface diffusion model. This work provides an effective methodology to construct macroscopic MOF-polymer beads for effective Pb(II) removal, and promote the actual application of MOFs in water treatment.

Pb (II) Recovery by Modified Tuffite: Adsorption, Desorption, and Kinetic Study

In this study, Pb (II) removal from wastewater was investigated using a modified vitric crystal tuffite with a BET surface area of 11.7 m2/g. For this purpose, tuffite was used in its natural and modified form with ethylenediaminetetraacetic acid (EDTA). Batch adsorption experiment was performed. The effects of contact time (0–90 min), adsorbent dosage (1–10 g/L), initial concentration (10–200 mg/L), and pH (2–12) on the removal of Pb (II) were investigated. The isotherm data were fitted to Langmuir, Freundlich, Temkin, and Redlich-Peterson isotherm models. Kinetic models such as pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used. In order to optimize the adsorption system and investigate the kinetic behaviour of adsorption, nonlinear isotherm and kinetic models were used as well as linearized models. Error analyses were made in order to express the obtained results more accurately. pH 5 was the optimum value for adsorption. According to nonlinear isotherm model calculations, Bayburt stone (BS) and its modified form (MBS) had $q_{\max }$ values of 335 and 584 mg/g, respectively. The Freundlich model, with its high correlation coefficients of about 1.00, was found to be more suitable for the adsorption of Pb (II) to MBS. The pseudo-second-order kinetic model with mean $R^2$ and $k_2$ values of 0.997 and 0.0116 1/min, respectively, was found to be more appropriate. According to the regeneration studies, the maximum desorption efficiency was 97.8%. The thermodynamic equilibrium coefficients obtained at different temperatures and $\Delta G^{\text{o}}$ , $\Delta H^{\text{o}}$ , and $\Delta S^{\text{o}}$ values were observed as -21.4, 46.4, and 163 kJ/mol, respectively. These values indicate that the adsorption of Pb (II) on to MBS was endothermic and spontaneous process. BS and MBS were characterized by different instrumental analyses such as SEM, EDS, FTIR, and zeta potential measurements.

Resource utilization of pig hair to prepare low-cost adsorbents with high density of sulfhydryl for enhanced and trace level removal of aqueous Hg(II)

Pig hair (PH), a keratinous waste, was modified by ammonium thioglycolate in a ball milling to promote its performance of Hg(II) sequestration. The ball milling broke the hydrophobic cuticle sheath and enhanced the reduction of disulfide bond, which increased the sulfydryl content of the modified PH (BTPH) from 0.07 to 11.05 μmol/g. BTPH exhibited a significantly higher capture capacity of Hg(II) (415.4 mg/g) than PH (3.1 mg/g), as well as the commercial activated carbon (219.7 mg/g), and persisted its performance over a wide range of solution pH. Meanwhile, BTPH with a distribution coefficient of 5.703 × 10⁵ mL/g could selectively capture Hg(II) from the water with the coexisting metal ions such as Mg(II), Cd(II) and Pb(II). Moreover, the low-cost BTPH could reduce the Hg(II) from 1.0 mg/L to well below the limit of drinkable water (2 μg/L) in real-world samples. Density functional theory (DFT) calculations and state-of-the-art characterizations illustrated that the binding of Hg(II) to sulfydryl groups was the main adsorption mechanism. Notably, BTPH decreased the mercury content of water spinaches from 24.1 to 0.50 mg/kg and thereby significantly reduced the phytotoxicity of Hg(II). This work therefore provides a sustainable way to utilize keratinous wastes for the remediation of aqueous Hg(II).

Efficient recovery of valuable metals from cathode materials of spent LiCoO2 batteries via co-pyrolysis with cheap carbonaceous materials

Recovery of valuable metals from spent Li-ion batteries has prominent economic and environmental benefits. In this study, a novel approach for recycling valuable metals from spent LiCoO₂ batteries via co-pyrolysis with three different carbonaceous materials (waste polyethylene, biomass, and coal)) was proposed and evaluated. The thermodynamic analysis proved that carbonaceous materials (mainly carbon) were theoretically able to facilitate the decomposition process of LiCoO₂. The promotion effect on LiCoO₂ decomposition was in the following order: coal > biomass > polyethylene, and the decomposition temperature of LiCoO₂ could significantly reduce by 400 °C via adding coal. The char produced from the carbonaceous materials, rather than the volatiles, played an important role in LiCoO₂ decomposition and reduction. The pyrolysis products of LiCoO₂ and coal mixture exhibited typical superparamagnetism and hysteresis behaviours, which benefitted the subsequent magnetic separation. The recovery rates of Co and Li were sensitive to the pyrolysis temperature and residence time, respectively. A high proportion of Co was in the form of CoO below 800 °C and had not been completely reduced, leading to the relatively lower recovery rates of Co below 800 °C. The optimal recovery rates of Co (96.8%) and Li (88.7%) were obtained at the pyrolysis temperature of 800 °C and the residence time of 10 min. The final recovery products were Co and Li₂CO₃ with rather high crystallinities and purities. Therefore, this study provided a novel approach for the efficient recycling of valuable metals from spent Li-ion batteries with high application prospects.