Facile preparation of a remarkable MOF adsorbent for Au(III) selective separation from wastewater: Adsorption, regeneration and mechanism

Determination of Azole Fungicide Residues in Fresh Juice by Magnetic Solid Phase Extraction Based on Fe3O4@ZnAl-LDH@MIL-53(Al) Sorbent in Combination with High-Performance Liquid Chromatograph

In this work, a magnetic adsorption material based on metal-organic framework (Fe3O4@ZnAl-LDH@MIL-53(Al)) was synthesized and used as an adsorbent in the process of magnetic solid phase extraction. Then, a high-performance liquid chromatograph was used to quantitatively detect triazole fungicides in samples. In order to verify the successful preparation of the material, a series of characterization analyses were carried out. Besides, the key parameters that may affect the extraction efficiency have been optimized, and under optimal conditions the three triazole fungicides showed good linearity in the range of 10-1000 μg/L (R2 ≥ 0.9796); Limit of detections were ranged from 0.013 to 0.030 μg/mL. Finally, the established method was applied to the detection of triazole fungicides in four fresh juice samples. The results showed that the target analyte was not detected in all the test samples. By detecting the recoveries (73.3-104.3%) and coefficient variation (RSD ≤ 6.8%) of triazole fungicides in fortified samples, it proved that this established method meets the requirements of pesticide residue analysis and showed excellent application potential.

Mining wastewater treatment technologies and resource recovery techniques: A review

Mining wastewater can have adverse effects on the ecosystem; thus, treatment before discharging into the environment is of utmost importance. This manuscript reports on the effect of mining wastewater on the environment. Moreover, the currently used, effective and commercialised mine wastewater treatment technologies such as SAVMIN®, SPARRO®, Biogenic sulphide, and DESALX® are reported in this study. These technologies integrate two or more separation processes, which have been proven to be effective for the high recovery of salts and water for reuse. Some of the technologies reported can significantly recover salts and >95% of water. Modern pilot-stage and laboratory-scale treatment systems used for the recovery and removal of metals are also reported herein. Since some treatment technologies can generate highly toxic sludge and other waste products, the management of the generated waste was also considered. Some studies have focused on the treatment of wastewater at the laboratory level using the adsorption process. Most adsorbents exhibit promising results; however, there is insufficient research on reusability, toxic sludge management, and the economic analysis of the systems. Moreover, the implementation of adsorption systems in wastewater is necessary. Furthermore, the integration of treatment systems to recover precious metals at low concentrations is desirable in addition to water reclamation to achieve circular mine water.

Efficient and selective capture of Au(III) from PCBs by pentaethylenehexamine-modified chloromethylated polystyrene beads

Recycling of gold promotes solving the problems of resource waste and environmental pollution. In this work, pentaethylenehexamine (PEHA)-modified chloromethylated polystyrene beads (PEHA-CMPS) was synthesized for the recovery of Au(III) from actual printed circuits boards (PCBs) leaching solution. PEHA-CMPS exhibited excellent adsorption efficiency at a wide pH range. It was discovered that the pseudo-second-order and Langmuir model provided a superior match for the Au(III) adsorption process. The maximum adsorption capacity for Au(III) was 1186 mg/g. Furthermore, PEHA-CMPS was able to selectively capture trace Au(III) with recovery efficiencies of above 80% from the actual PCBs leaching solution. In addition, the column separation approach was utilized to better assess the practical applications for PEHA-CMPS, proving that the prepared adsorbent exhibited great prospects in industrial applications. The adsorption efficiency still maintained 95% after five adsorption-desorption cycles. The FTIR, XRD, and XPS analyses demonstrated that Au(III) uptake on PEHA-CMPS was a collaborative process involving electrostatic interaction, chelation, and oxidation-reduction. The PEHA-CMPS provided a promising strategy in Au(III) recovery and environmental remediation.

Immobilization of tannin onto dialdehyde chitosan as a strategy for highly efficient and selective Au(III) adsorption

Recycling of Au(III) from wastewater can not only increase resource utilization but also reduce environmental pollution. Herein, a chitosan-based bio-adsorbent (DCTS-TA) was successfully synthesized via crosslinking reaction between tannin (TA) and dialdehyde chitosan (DCTS) for the recovery of Au(III) from the solution. The maximum adsorption capacity for Au(III) was 1146.59 mg/g at pH 3.0, which fitted well with the Langmuir model. The XRD, XPS, and SEM-EDS analyses demonstrated that Au(III) adsorption on DCTS-TA was a collaborative process involving electrostatic interaction, chelation, and redox reaction. Existence of multiple coexisting metal ions did not significantly affect the Au(III) adsorption efficiency, with >90 % recovery of DCTS-TA obtained after five cycles. DCTS-TA is a promising candidate for Au(III) recovery from aqueous solutions due to its easy preparation, environmental-friendliness, and high efficiency.

Extraction of Gold Based on Ionic Liquid Immobilized in UiO-66: An Efficient and Reusable Way to Avoid IL Loss Caused by Ion Exchange in Solvent Extraction

Ionic liquids (ILs) have received considerable attention as a promising green solvent for extracting metal ions from aqueous solutions. However, the recycling of ILs remains difficult and challenging because of the leaching of ILs, which is caused by the ion exchange extraction mechanism and hydrolysis of ILs in acidic aqueous conditions. In this study, a series of imidazolium-based ILs were confined in a metal-organic framework (MOF) material (UiO-66) to overcome the limitations when used in solvent extraction. The effect of the various anions and cations of the ILs on the adsorption ability of AuCl₄^- was studied, and 1-hexyl-3-methylimidazole tetrafluoroborate ([HMIm]⁺[BF₄]^-@UiO-66) was used for the construction of a stable composite. The adsorption properties and mechanism of [HMIm]⁺[BF₄]^-@UiO-66 for Au(III) adsorption were also studied. The concentrations of tetrafluoroborate ([BF₄]^-) in the aqueous phase after Au(III) adsorption by [HMIm]⁺[BF₄]^-@UiO-66 and liquid-liquid extraction by [HMIm]⁺[BF₄]^- IL were 0.122 mg/L and 18040 mg/L, respectively. The results reveal that Au(III) coordinated with the N-containing functional groups, while [BF₄]^- was effectively confined in UiO-66, instead of undergoing anion exchange in liquid-liquid extraction. Electrostatic interactions and the reduction of Au(III) to Au(0) were also important factors determining the adsorption ability of Au(III). [HMIm]⁺[BF₄]^-@UiO-66 could be easily regenerated and reused for three cycles without any significant drop in the adsorption capacity.

Extraction of Au(iii) from hydrochloric acid media using a novel amide-based ionic liquid

A study on the performance of selective extraction of Au(iii) using a novel amide-based IL.

Fabrication and Characterization of Xanthan Gum-cl-poly(acrylamide-co-alginic acid) Hydrogel for Adsorption of Cadmium Ions from Aqueous Medium

The present research demonstrates the facile fabrication of xanthan gum-cl-poly(acrylamide-co-alginic acid) (XG-cl-poly(AAm-co-AA)) hydrogel by employing microwave-assisted copolymerization. Simultaneous copolymerization of acrylamide (AAm) and alginic acid (AA) onto xanthan gum (XG) was carried out. Different samples were fabricated by changing the concentrations of AAm and AA. A sample with maximum swelling percentage was chosen for adsorption experiments. The structural and functional characteristics of synthesized hydrogel were elucidated using diverse characterization tools. Adsorption performance of XG-cl-poly(AAm-co-AA) hydrogel was investigated for the removal of noxious cadmium (Cd(II)) ions using batch adsorption from the aqueous system, various reaction parameters optimized include pH, contact time, temperature, and concentration of Cd(II) ions and temperature. The maximum adsorption was achieved at optimal pH 7, contact time 180 min, temperature 35 °C and cadmium ion centration of 10 mg·L-1. The XG-cl-poly(AAm-co-AA) hydrogel unveiled a very high adsorption potential, and its adsorption capacities considered based on the Langmuir isotherm for Cd(II) ions was 125 mg·g-1 at 35 °C. The Cd(II) ions adsorption data fitted nicely to the Freundlich isotherm and pseudo-first-order model. The reusability investigation demonstrated that hydrogel retained its adsorption capacity even after several uses without significant loss.