In vitro and in vivo evaluation of electrospun nanofibers of PCL, chitosan and gelatin: A comparative study

Electrospun polycaprolactone-chitosan nanofibers on a zinc mesh as biodegradable guided bone-regeneration membranes with enhanced mechanical, antibacterial, and osteogenic properties for alveolar bone-repair applications

Guided bone-regeneration membrane (GBRM) is commonly used in bone-repair surgery because it blocks fibroblast proliferation and provides spatial support in bone-defect spaces. However, the need for removal surgery and the lack of antibacterial properties of conventional GBRM limit its therapeutic applicability for alveolar bone defects. Here we developed a GBRM for alveolar bone-repair and -regeneration applications through double-sided electrospinning of polycaprolactone and chitosan layers on a Zn mesh surface (denoted DSZM). The DSZM showed a UTS of ∼25.6 MPa, elongation of ∼16.1%, strength-elongation product of ∼0.413 GPa%, and ultrahigh spatial maintenance ability, and the UTS was over 6 times higher than that of commercial Bio-Gide membrane. The DSZM exhibited a corrosion rate of ∼17 µm/y and a Zn ion concentration of ∼0.23 µg/ml after 1 month of immersion in Hanks' solution. The DSZM showed direct and indirect cytocompatibility with exceptional osteogenic differentiation and calcium deposition toward MC3T3-E1 cells. Further, the DSZM showed strongly sustained antibacterial activity against S. aureus and osteogenesis in a rat critical-sized maxillary defect model. Overall, the DSZM fits the requirements for alveolar bone-repair and -regeneration applications as a biodegradable GBRM material due to its spatial support, suitable degradability, cytocompatibility, and antibacterial and osteogenic capabilities. STATEMENT OF SIGNIFICANCE: This work reports the mechanical properties, antibacterial ability and osteogenic properties of electrospun PCL-CS nanofiber on Zn mesh as biodegradable guided bone-regeneration membrane for alveolar bone-repair applications. Our findings demonstrate that the DSZM prepared by double-sided electrospinning of PCL-CS layers on Zn mesh showed a UTS of ∼25.6 MPa, elongation of ∼16.1%, strength-elongation product of ∼0.413 GPa%, and ultrahigh spatial maintenance ability, and the UTS was over 6 times greater than that of commercial Bio-Gide® membrane. The DSZM showed direct and indirect cytocompatibility with exceptional osteogenic differentiation and calcium deposition toward MC3T3-E1 cells. Further, the DSZM showed strongly sustained antibacterial activity against S. aureus and osteogenesis in a rat critical-sized maxillary defect model.

Optimization of Diclofenac-Loaded Bicomponent Nanofibers: Effect of Gelatin on In Vitro and In Vivo Response

The use of electrospun fibers as anti-inflammatory drug carriers is currently one of the most interesting approaches for the design of drug delivery systems. In recent years, biodegradable polymers blended with naturally derived ones have been extensively studied to fabricate bioinspired platforms capable of driving biological responses by releasing selected molecular/pharmaceutical signals. Here, sodium diclofenac (DicNa)-loaded electrospun fibers, consisting of polycaprolactone (PCL) or gelatin-functionalized PCL, were studied to evaluate fibroblasts' in vitro and in vivo response. In vitro studies demonstrated that cell adhesion of L929 cells (≈70%) was not affected by the presence of DicNa after 4 h. Moreover, the initial burst release of the drug from PD and PGD fibers, e.g., 80 and 48%, respectively, after 5 h-combined with its sustained release-did not produce any cytotoxic effect and did not negatively influence the biological activity of the cells. In particular, it was demonstrated that the addition of gelatin concurred to slow down the release mechanism, thus limiting the antiproliferative effect of DicNa, as confirmed by the significant increase in cell viability and collagen deposition after 7 days, with respect to PCL alone. In vivo studies in a rat subcutaneous model also confirmed the ability of DicNa-loaded fibers to moderate the inflammatory/foreign body response independently through the presence of gelatin that played a significant role in supporting the formation of small-caliber vessels after 10 days of implantation. All of these results suggest using bicomponent fibers loaded with DicNa as a valid therapeutic tool capable of supporting the wound healing process and limiting in vivo inflammation and rejection phenomena.

Electrospinning-netting of spider-inspired polycaprolactone/collagen nanofiber-nets incorporated with Propolis extract for enhanced wound healing applications

Nanofibers hold significant promise for wound healing applications, but their potential is limited by their large diameter. To overcome this limitation, the development of nanofibrous systems with refined nanonets (approximately 20 nm in diameter) represents a notable improvement. In this study, a composite of polycaprolactone/collagen (PCLC) nano-fiber/nets (NFNs) was fabricated using benign solvents (acetic acid and formic acid) via the electro-spinning/netting (ESN) technique, harnessing the regenerative potential of collagen as a biological macromolecule. Additionally, to enhance the natural attributes of the NFNs structure, Propolis extract, renowned for its wound healing properties, was incorporated. Five ESN solutions were prepared: PCL, PCLC, PCLC/Pro 5 %, PCLC/Pro 10 %, and PCLC/Pro 15 %. NaCl salt was introduced into all ESN solutions to improve nanonets formation. FE-SEM imaging demonstrated successful nano-net formation in all ESN solutions except for the PCL formulation. The fabricated scaffolds exhibited spider-like nanonets with the addition of collagen and further enhanced nano-net formation with Propolis incorporation. Trunk nanofibers showed filamentous structures without any beads, with an average diameter of 164-728 nm, while the diameter of branched fibers (nanonets) was approximately 20 nm. WVTR values of the NFNs were comparable to commercial dressings such as Tegaderm. The results also demonstrated the potent cytoprotective effects of Propolis-loaded NFNs in a dose-dependent manner. Furthermore, the viability of HFF-2 cells after 72 h of culture on PCLC NFNs significantly increased compared to PCL nanofibers. The highest cell viability was observed in PCLC/Pro 15 % nanofibers after 24, 48, and 72 h of cell culture, indicating the proliferative effect of Propolis extract in nanoformulated form. Additionally, the scaffolds exhibited a hemocompatibility of <3 %, further highlighting their potential in wound healing therapeutics.

Synthesis of biocomposites from microalgal peptide incorporated polycaprolactone/ κ- carrageenan nanofibers and their antibacterial and wound healing property

Antimicrobial peptides (AMPs) are promising novel agents for targeting a wide range of pathogens. In this study, microalgal peptides derived from native microalgae were incorporated into polycaprolactone (PCL) with ƙ-Carrageenan (ƙ-C) forming nanofibers using the electrospinning method. The peptides incorporated in the nanofibers were characterized by fourier infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy (SEM), and contact angle measurement. The results showed that peptides with molecular weights < 10 kDa, when loaded into nanofibers, exhibited lower wettability. The SEM analysis revealed a thin, smooth, interconnected bead-like structures. The antimicrobial activity of the electrospun nanofibers was evaluated through disc diffusion, and minimum inhibitory activity against Escherichia coli (MTTC 443), and Staphylococcus aureus (MTTC 96), resulting in zones of inhibition of 24 ± 0.5 mm and 14 ± 0.5 mm, respectively. The in vitro biocompatibility of the synthesized nanofibers was confirmed using in HEK 293 cell lines with an increased cell viability. Interestingly, the fibers also exhibited a significant wound-healing properties when used in vitro scratch assays. In conclusion, algal peptides incorporated with PCL/ ƙ-C were found to exhibit antimicrobial and biocompatible biomaterials for wound healing applications.

Small-diameter vascular graft composing of core-shell structured micro-nanofibers loaded with heparin and VEGF for endothelialization and prevention of neointimal hyperplasia

Despite the significant progress made in recent years, clinical issues with small-diameter vascular grafts related to low mechanical strength, thrombosis, intimal hyperplasia, and insufficient endothelialization remain unresolved. This study aims to design and fabricate a core-shell fibrous small-diameter vascular graft by co-axial electrospinning process, which will mechanically and biologically meet the benchmarks for blood vessel replacement. The presented graft (PGHV) comprised polycaprolactone/gelatin (shell) loaded with heparin-VEGF and polycaprolactone (core). This study hypothesized that the shell structure of the fibers would allow rapid degradation to release heparin-VEGF, and the core would provide mechanical strength for long-term application. Physico-mechanical evaluation, in vitro biocompatibility, and hemocompatibility assays were performed to ensure safe in vivo applications. After 25 days, the PGHV group released 79.47 ± 1.54% of heparin and 86.25 ± 1.19% of VEGF, and degradation of the shell was observed but the core remained pristine. Both the control (PG) and PGHV groups demonstrated robust mechanical properties. The PGHV group showed excellent biocompatibility and hemocompatibility compared to the PG group. After four months of rat aorta implantation, PGHV exhibited smooth muscle cell regeneration and complete endothelialization with a patency rate of 100%. The novel core-shell structured graft could be pivotal in vascular tissue regeneration application.

Anti-adhesive and antibacterial chitosan/PEO nanofiber dressings with high breathability for promoting wound healing

Wound dressings are crucial for wound healing. Ideal wound dressings should possess many functions such as wettability, antibacterial activity and anti-adherent property to promote wound healing. In the present study solution blown spinning (SBS) technology was applied to prepare chitosan/polyethylene oxide (CS/PEO) nanofiber dressings in high efficiency. The obtained nanofiber dressings were treated with anhydrous ethanol to improve the fiber structure and enhance the functionality of the fiber dressings. The results show that the treated nanofibers had higher crystallinities and higher CS contents. The CS/PEO nanofiber dressings fabricated by using no additives and crosslinking had excellent wettability, water stability and antibacterial activity against Escherichia coli and Staphylococcus aureus reached to over 99.99 %. In addition, the CS/PEO nanofiber dressings exhibited high breathability, antioxidant activity and anti-adhesion function. The in vivo animal experiment confirmed that the nanofiber dressings enhanced cell proliferation and significantly accelerated the wound healing within 10 days. The developed CS/PEO nanofiber dressings have great potential in the clinical field of wound healing.

Chitosan-Based Biomaterial in Wound Healing: A Review

Wound healing is an evolving and intricate technique that is vital to the restoration of tissue integrity and function. Over the past few decades, chitosan a biopolymer derived from chitin, became known as an emerging biomaterial in the field of healing wounds due to its distinctive characteristics including biocompatibility, biodegradability, affinity to biomolecules, and wound-healing activity. This natural polymer exhibits excellent healing capabilities by accelerating the development of new skin cells, reducing inflammation, and preventing infections. Due to its distinct biochemical characteristics and innate antibacterial activity, chitosan has been extensively researched as an antibacterial wound dressing. Chronic wounds, such as diabetic ulcers and liver disease, are a growing medical problem. Chitosan-based biomaterials are a promising solution in the domain of wound care. The article analyzes the depth of chitosan-based biomaterials and their impact on wound healing and also the methods to enhance the advantages of chitosan by incorporating bioactive compounds. This literature review is aimed to improve the understanding and knowledge about biomaterials and their use in wound healing.

Overview of Tissue Engineering and Drug Delivery Applications of Reactive Electrospinning and Crosslinking Techniques of Polymeric Nanofibers with Highlights on Their Biocompatibility Testing and Regulatory Aspects

Traditional electrospinning is a promising technique for fabricating nanofibers for tissue engineering and drug delivery applications. The method is highly efficient in producing nanofibers with morphology and porosity similar to the extracellular matrix. Nonetheless, and in many instances, the process has faced several limitations, including weak mechanical strength, large diameter distributions, and scaling-up difficulties of its fabricated electrospun nanofibers. The constraints of the polymer solution's intrinsic properties are primarily responsible for these limitations. Reactive electrospinning constitutes a novel and modified electrospinning techniques developed to overcome those challenges and improve the properties of the fabricated fibers intended for various biomedical applications. This review mainly addresses reactive electrospinning techniques, a relatively new approach for making in situ or post-crosslinked nanofibers. It provides an overview of and discusses the recent literature about chemical and photoreactive electrospinning, their various techniques, their biomedical applications, and FDA regulatory aspects related to their approval and marketing. Another aspect highlighted in this review is the use of crosslinking and reactive electrospinning techniques to enhance the fabricated nanofibers' physicochemical and mechanical properties and make them more biocompatible and tailored for advanced intelligent drug delivery and tissue engineering applications.

In Vitro and Anti-Inflammatory Activity Evaluation Nanofibers from a Breath Mask and Filter Based on Polyurethane and Polyvinylidene Fluoride

Nanofiber (NF) products exhibit outstanding performances in materials science, textiles, and medicine that cannot be realized using conventional technologies. However, the safety of such products is debated because of the potential health risks that nanomaterials pose and the lack of standardized guidelines for the safety evaluation of NF products. The global safety evaluations of nanomaterials have focused on evaluating the cytotoxicity of low-dimensional materials, including nanoparticles and nanotubes, based on OECD (Organization for Economic Co-operation and Development) criteria. NFs are one-dimensional materials with nanometer diameters and considerable lengths. Many fibers are applied in a densely woven web-like form, so assessing cellular penetration and fiber toxicity using the same methods is inappropriate. This study verifies the safety of the polyurethane (PU) and polyvinylidene fluoride (PVDF) polymers currently applied in filters and masks. To this end, polymer NFs were collected from each product, and the NFs were compared with reference samples using FT-IR and Raman spectroscopy. For the safety evaluation, DMSO stocks of varying concentrations of PVDF and PU NFs (at 0.5, 1, 5, and 10 μg/mL) were prepared. The cytotoxicity and inhibitory effects on nitric oxide production and protein expression obtained via Western blot were identified.

Fish Scale Gelatin Nanofibers with Helichrysum italicum and Lavandula latifolia Essential Oils for Bioactive Wound-Healing Dressings

Essential oils are valuable alternatives to synthetic antibiotics that have the potential to avoid the pathogen resistance side effects generated by leather. Helichrysum italicum and Lavandula latifolia essential oils combined with fish scale gelatin were electrospun using a coaxial technique to design new bioactive materials for skin wound dressings fabrication. Fish scale gelatins were extracted from carp fish scales using two variants of the same method, with and without ethylenediaminetetraacetic acid (EDTA). Both variants showed very good electrospinning properties when dissolved in acetic acid solvent. Fish scale gelatin nanofibers with Helichrysum italicum and Lavandula latifolia essential oil emulsions ensured low microbial load (under 100 CFU/g of total number of aerobic microorganisms and total number of yeasts and filamentous fungi) and the absence of Staphylococcus aureus ATCC 6538, Escherichia coli ATCC 10536, and Candida albicans ATCC 1023 as compared to fish scale gelatin without essential oils, which recommends them for pharmaceutical or topical applications. A scratch-test performed on human dermal fibroblasts proved that the biomaterials contributing to the wound healing process included fish scale gelatin nanofibers without EDTA (0.5% and 1%), fish scale gelatin nanofibers without EDTA and Lavandula latifolia essential oil emulsion (1%), fish scale gelatin nanofibers with EDTA (0.6%), and fish scale gelatin nanofibers with EDTA with Helichrysum italicum essential oil emulsion (1% and 2%).

Influence of mechanochemically fabricated nano-hardystonite reinforcement in polycaprolactone scaffold for potential use in bone tissue engineering: Synthesis and characterization

Bone tissue engineering (BTE) has gained significant attention for the regeneration of bone tissue, particularly for critical-size bone defects. The aim of this research was first to synthesize nanopowders of hardystonite (HT) through ball milling and then to manufacture composite scaffolds for BTE use out of polycaprolactone (PCL) containing 0, 3, 5, and 10 wt% HT by electrospinning method. The crystallite size of the synthesized HT nanopowders was 42.8 nm. including up to 5 wt% HT into PCL scaffolds resulted in significant improvements, such as a reduction in the fiber diameter from 186.457±15.74 to 150.021±21.99 nm, a decrease in porosity volume from 85.2±2.5 to 80.3±3.3 %, an improvement in the mechanical properties (ultimate tensile strength: 5.7±0.2 MPa, elongation: 47.5±3.5 %, tensile modulus: 32.7±0.9 MPa), an improvement in the hydrophilicity, and biodegradability. Notably, PCL/5%HT exhibited the maximum cell viability (194±14 %). Additionally, following a 4-week of submersion in simulated body fluid (SBF), the constructed PCL/HT composite scaffolds showed a remarkable capacity to stimulate the development of hydroxyapatite (HA), which increased significantly for the 5 wt% HT scaffolds. However, at 10 wt% HT, nanopowder agglomeration led to an increase in the fiber diameter and a decrease in the mechanical characteristics. Collectively, the PCL/5%HT composite scaffolds can therefore help with the regeneration of the critical-size bone defects and offer tremendous potential for BTE applications.

Electrospun Scaffolds as Antimicrobial Herbal Extract Delivery Vehicles for Wound Healing

Herbal extracts have been used in traditional remedies since the earliest myths. They have excellent antimicrobial, anti-inflammatory, and antioxidant activities owing to various bioactive components in their structure. However, due to their inability to reach a target and low biostability, their use with a delivery vehicle has come into prominence. For this purpose, electrospun nanofibrous scaffolds have been widely preferred for the delivery and release of antimicrobial herbal extracts due to the flexibility and operational versatility of the electrospinning technique. Herein, we briefly reviewed the electrospun nanofibrous scaffolds as delivery systems for herbal extracts with a particular focus on the preclinical studies for wound-healing applications that have been published in the last five years. We also discussed the indirect effects of herbal extracts on wound healing by altering the characteristics of electrospun mats.

Biomimetic Scaffolds for Tendon Tissue Regeneration

Tendon tissue connects muscle to bone and plays crucial roles in stress transfer. Tendon injury remains a significant clinical challenge due to its complicated biological structure and poor self-healing capacity. The treatments for tendon injury have advanced significantly with the development of technology, including the use of sophisticated biomaterials, bioactive growth factors, and numerous stem cells. Among these, biomaterials that the mimic extracellular matrix (ECM) of tendon tissue would provide a resembling microenvironment to improve efficacy in tendon repair and regeneration. In this review, we will begin with a description of the constituents and structural features of tendon tissue, followed by a focus on the available biomimetic scaffolds of natural or synthetic origin for tendon tissue engineering. Finally, we will discuss novel strategies and present challenges in tendon regeneration and repair.

Design of IKVAV peptide/gold nanoparticle decorated, micro/nano-channeled PCL/PLGA film scaffolds for neuronal differentiation and neurite outgrowth

In the field of neural tissue engineering, intensive efforts are being made to develop tissue scaffolds that can support an effective functional recovery and neural development by guiding damaged axons and neurites. Micro/nano-channeled conductive biomaterials are considered a promising approach for repairing the injured neural tissues. Many studies have demonstrated that the micro/nano-channels and aligned nanofibers could guide the neurites to extend along the direction of alignment. However, an ideal biocompatible scaffold containing conductive arrays that could promote effective neural stem cell differentiation and development, and also stimulate high neurite guidance has not been fully developed. In the current study, we aimed to fabricate micro/nano-channeled polycaprolactone (PCL)/Poly-d,l-lactic-co-glycolic acid (PLGA) hybrid film scaffolds, decorate their surfaces with IKVAV pentapeptide/gold nanoparticles (AuNPs), and investigate the behavior of PC12 cells and neural stem cells (NSCs) on the developed biomaterial under static/bioreactor conditions. Here we show that channeled groups decorated with AuNPs highly promote neurite outgrowth and neuronal differentiation along linear lines in the presence of electrical stimulation, compared with the polypyrrole (PPy) coating, which has been used traditionally for many years. Hopefully, this newly developed channeled scaffold structure (PCL/PLGA-AuNPs-IKVAV) could help to support long-distance axonal regeneration and neuronal development after different neural damages.

Carboxymethyl cellulose/poloxamer gels enriched with essential oil and Ag nanoparticles: promising wound dressings

Aim: Essential oils are promising antibacterial and wound-healing agents that should be explored for the design of wound dressings. Materials & methods: Topical gels prepared from a combination of carboxymethyl cellulose and poloxamer were incorporated with tea tree and lavender oil together with Ag nanoparticles. In vitro release, cytotoxicity, antibacterial, and wound healing studies were performed. Results: The gels displayed good spreadability with viscosity in the range of 210-1200 cP. The gels displayed promising antibacterial activity against selected Gram-positive and Gram-negative bacteria used in the study. The % cell viability of the gels was more than 90.83%. Conclusion: The topical gels displayed excellent wound closure in vitro revealing that they are potential wound dressings for bacteria-infected wounds.

Preclinical animal study of electrospun poly (l-lactide-co-caprolactone) and formulated porcine fibrinogen for full-thickness diabetic wound regeneration

Diabetic foot ulcer is one of the most serious chronic complications of diabetes mellitus. It may lead to amputation of the lower extremities for diabetics. Our study was to evaluate the effect of electrospun poly (L-lactide-co-caprolactone) and formulated porcine fibrinogen (PLCL/Fg) wound dressing on animal wound model. A blend ratio of PLCL/Fg scaffold was 4 (PLCL):1 (Fg). The scanning electron microscopy findings showed that the fibers' diameter was 122.5 ± 80.3 nm, and the tensile strength was 9.2 ± 0.2 MPa. In-vivo study of the hog normal model demonstrated that PLCL/Fg dressing had better biocompatibility, degradability, and ability to restore the skin's normal structure. We evaluated the wound healing processes in the rat diabetic model by macroscopic observation and histological observation at 1, 2, and 3 post-operation weeks. In our study, the PLCL/Fg group performed better 3 weeks after surgery, in terms of macroscopic healing and scarring. After surgery, the PLCL/Fg group showed better fibroblast accumulation, tissue granulation, and collagen expression than the control group. Topical treatment with PLCL/Fg dressing effectively enhanced wound healing in both normal and hyperglycemic conditions, suggesting that it may possess wound-healing potential.

Synthesis and Design of a Synthetic-Living Material Composed of Chitosan, Calendula officinalis Hydroalcoholic Extract, and Yeast with Applications as a Biocatalyst

Design and development of materials that couple synthetic and living components allow taking advantage of the complexity of biological systems within a controlled environment. However, their design and fabrication represent a challenge for material scientists since it is necessary to synthesize synthetic materials with highly specialized biocompatible and physicochemical properties. The design of synthetic-living materials (vita materials) requires materials capable of hosting cell ingrowth and maintaining cell viability for extended periods. Vita materials offer various advantages, from simplifying product purification steps to controlling cell metabolic activity and improving the resistance of biological systems to external stress factors, translating into reducing bioprocess costs and diversifying their industrial applications. Here, chitosan sponges, functionalized with Calendula officinalis hydroalcoholic extract, were synthesized using the freeze-drying method; they showed small pore sizes (7.58 μm), high porosity (97.95%), high water absorption (1695%), and thermal stability, which allows the material to withstand sterilization conditions. The sponges allowed integration of 58.34% of viable Saccharomyces cerevisiae cells, and the cell viability was conserved 12 h post-process (57.14%) under storage conditions [refrigerating temperature (4 °C) and without a nutrient supply]. In addition, the synthesized vita materials conserved their biocatalytic activity after 7 days of the integration process, which was evaluated through glucose consumption and ethanol production. The results in this paper describe the synthesis of complex vita materials and demonstrate that biochemically modified chitosan sponges can be used as a platform material to host living and metabolically active yeast with diverse applications as biocatalysts.

Cell-based wound dressing: Bilayered PCL/gelatin nanofibers-alginate/collagen hydrogel scaffold loaded with mesenchymal stem cells

Wound dressing is applied to promote the healing process, wound protection, and additionally regeneration of injured skin. In this study, a bilayer scaffold composed of a hydrogel and nanofibers was fabricated to improve the regeneration of injured skin. To this end, polycaprolactone/gelatin (PCL/Gel) nanofibers were electrospun directly on the prepared collagen/alginate (Col/Alg) hydrogel. The bilayer scaffold was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), mechanical properties, and swelling/degradation time. Cytotoxicity assays were evaluated using MTT assay. Then, the nanofiber and bilayer scaffolds were seeded with Adipose-derived stem cells (ADSCs). ADSCs were isolated from rat adipose tissue and analyzed using flow cytometry, in advance. Full-thickness wounds on the backs of rats were dressed with ADSCs-seeded bilayer scaffolds and nanofibers. Histopathological evaluations were performed after 14 and 21 days using H&E (hematoxylin and eosin) staining. The results indicated that re-epithelialization, angiogenesis, and collagen remodeling were enhanced in ADSCs-seeded bilayer scaffolds and nanofibers in comparison with the control group. In conclusion, the best re-epithelialization, collagen organization, neovascularization, and low presence of inflammation in the wound area were observed in the ADSCs-seeded bilayer scaffolds.

Recent progressions in biomedical and pharmaceutical applications of chitosan nanoparticles: A comprehensive review

Nowadays, the most common approaches in the prognosis, diagnosis, and treatment of diseases are along with undeniable limitations. Thus, the ever-increasing need for using biocompatible natural materials and novel practical modalities is required. Applying biomaterials, such as chitosan nanoparticles (CS NPs: FDA-approved long-chain polymer of N-acetyl-glucosamine and D-glucosamine for some pharmaceutical applications), can serve as an appropriate alternative to overcome these limitations. Recently, the biomedical applications of CS NPs have extensively been investigated. These NPs and their derivatives can not only prepare through different physical and chemical approaches but also modify with various molecules and bioactive materials. The potential properties of CS NPs, such as biocompatibility, biodegradability, serum stability, solubility, non-immunogenicity, anti-inflammatory properties, appropriate pharmacokinetics and pharmacodynamics, and so forth, have made them excellent candidates for biomedical applications. Therefore, CS NPs have efficiently applied for various biomedical applications, like regenerative medicine and tissue engineering, biosensors for the detection of microorganisms, and drug delivery systems (DDS) for the suppression of diseases. These NPs possess a high level of biosafety. In summary, CS NPs have the potential ability for biomedical and clinical applications, and it would be remarkably beneficial to develop new generations of CS-based material for the future of medicine.

A Review of 3D Polymeric Scaffolds for Bone Tissue Engineering: Principles, Fabrication Techniques, Immunomodulatory Roles, and Challenges

Over the last few years, biopolymers have attracted great interest in tissue engineering and regenerative medicine due to the great diversity of their chemical, mechanical, and physical properties for the fabrication of 3D scaffolds. This review is devoted to recent advances in synthetic and natural polymeric 3D scaffolds for bone tissue engineering (BTE) and regenerative therapies. The review comprehensively discusses the implications of biological macromolecules, structure, and composition of polymeric scaffolds used in BTE. Various approaches to fabricating 3D BTE scaffolds are discussed, including solvent casting and particle leaching, freeze-drying, thermally induced phase separation, gas foaming, electrospinning, and sol-gel techniques. Rapid prototyping technologies such as stereolithography, fused deposition modeling, selective laser sintering, and 3D bioprinting are also covered. The immunomodulatory roles of polymeric scaffolds utilized for BTE applications are discussed. In addition, the features and challenges of 3D polymer scaffolds fabricated using advanced additive manufacturing technologies (rapid prototyping) are addressed and compared to conventional subtractive manufacturing techniques. Finally, the challenges of applying scaffold-based BTE treatments in practice are discussed in-depth.

Mechanics of gelatin-based hydrogels during finite strain tension, compression and shear

Introduction: Among the biopolymers used to make hydrogels, gelatin is very attractive due to its biocompatibility, biodegradability and versatile physico-chemical properties. A proper and complete characterization of the mechanical behavior of these hydrogels is critical to evaluate the relevance of one formulation over another for a targeted application, and to optimise their processing route accordingly. Methods: In this work, we manufactured neat gelatin and gelatin covalently cross-linked with glutaraldehyde at various concentrations, yielding to hydrogels with tunable mechanical properties that we characterized under finite strain, cyclic tension, compression and shear loadings. Results and Discussion: The role of both the chemical formulation and the kinematical path on the mechanical performances of the gels is highlighted. As an opening towards biomedical applications, the properties of the gels are confronted to those of native soft tissues particularly complicated to restore, the human vocal folds. A specific cross-linked hydrogel is selected to mimic vocal-fold fibrous tissues.

Physio-Chemical and Biological Characterization of Novel HPC (Hydroxypropylcellulose):HAP (Hydroxyapatite):PLA (Poly Lactic Acid) Electrospun Nanofibers as Implantable Material for Bone Regenerative Application

The research on extracellular matrix (ECM) is new and developing area that covers cell proliferation and differentiation and ensures improved cell viability for different biomedical applications. Extracellular matrix not only maintains biological functions but also exhibits properties such as tuned or natural material degradation within a given time period, active cell binding and cellular uptake for tissue engineering applications. The principal objective of this study is classified into two categories. The first phase is optimization of various electrospinning parameters with different concentrations of HAP-HPC/PLA(hydroxyapatite-hydroxypropylcellulose/poly lactic acid). The second phase is in vitro biological evaluation of the optimized mat using MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide) assay for bone regeneration applications. Conductivity and dielectric constant were optimized for the production of thin fiber and bead free nanofibrous mat. With this optimization, the mechanical strength of all compositions was found to be enhanced, of which the ratio of 70:30 hit a maximum of 9.53 MPa (megapascal). Cytotoxicity analysis was completed for all the compositions on MG63 cell lines for various durations and showed maximum cell viability on 70:30 composition for more than 48 hrs. Hence, this investigation concludes that the optimized nanofibrous mat can be deployed as an ideal material for bone regenerative applications. In vivo study confirms the HAP-HPC-PLA sample shows more cells and bone formation at 8 weeks than 4 weeks.

Chitosan-Based Membranes for Skin Wound Repair in a Dorsal Fold Chamber Rat Model

Frequently, deep partial and full-thickness skin wounds do not spontaneously regenerate. To restore the normal function of skin, epidermal and dermal components have to be supplied to the wound bed by grafting various substrates. Available options are limited and frequently costly. Herein, authors present a possible approach using 3D skin scaffolds capable of mimicking structure and biological functions of the extracellular matrix, providing, in parallel, a good environment for cell attachment, proliferation and differentiation. Low-molecular weight chitosan-based membranes were prepared by freeze-drying and ionizing radiation techniques to be used as skin scaffolds. Poly (vinyl alcohol), PVA, vinyl pyrrolidone, VP, and gelatin from cold water fish were incorporated. Information regarding membranes' physical-chemical properties from SEM analysis, swelling and weight loss, together with biological response through in vitro assays (using Human Caucasian Fetal Foreskin Fibroblast) allowed the selection of an optimized batch of membranes that was used as skin scaffold in a dorsal rat model wound. The in vivo implantation assays (in Wistar rats) resulted in very promising results: (i) healing process faster than control; (ii) good vascularization; (iii) viable new tissues morphologically functional.

Evaluation of Magnesium-Phosphate Particle Incorporation into Co-Electrospun Chitosan-Elastin Membranes for Skin Wound Healing

Major challenges facing clinicians treating burn wounds are the lack of integration of treatment to wound, inadequate mechanical properties of treatments, and high infection rates which ultimately lead to poor wound resolution. Electrospun chitosan membranes (ESCM) are gaining popularity for use in tissue engineering applications due to their drug loading ability, biocompatibility, biomimetic fibrous structure, and antimicrobial characteristics. This work aims to modify ESCMs for improved performance in burn wound applications by incorporating elastin and magnesium-phosphate particles (MgP) to improve mechanical and bioactive properties. The following ESCMs were made to evaluate the individual components’ effects; (C: chitosan, CE: chitosan-elastin, CMg: chitosan-MgP, and CEMg: chitosan-elastin-MgP). Membrane properties analyzed were fiber size and structure, hydrophilic properties, elastin incorporation, MgP incorporation and in vitro release, mechanical properties, degradation profiles, and in vitro cytocompatibility with NIH3T3 fibroblasts. The addition of both elastin and MgP increased the average fiber diameter of CE (~400 nm), CMg (~360 nm), and CEMg (565 nm) compared to C (255 nm). Water contact angle analysis showed elastin incorporated membranes (CE and CEMg) had increased hydrophilicity (~50°) compared to the other groups (C and CMg, ~110°). The results from the degradation study showed mass retention of ~50% for C and CMg groups, compared to ~ 30% seen in CE and CEMg after 4 weeks in a lysozyme/PBS solution. CMg and CEMg exhibited burst-release behavior of ~6 µg/ml or 0.25 mM magnesium within 72 h. In vitro analysis with NIH3T3 fibroblasts showed CE and CEMg groups had superior cytocompatibility compared to C and CMg. This work has demonstrated the successful incorporation of elastin and MgP into ESCMs and allows for future studies on burn wound applications.

Electrospun Sulfonatocalix[4]arene Loaded Blended Nanofibers: Process Optimization and In Vitro Studies

In the past decade, electrospun nanofibers made of biodegradable polymers have been used for different biomedical applications due to their flexible features in terms of surface area to volume ratio, pores, and fiber size, as well as their highly tunable surface properties. Recently, interest is growing in the use of supramolecular structures in combination with electrospun nanofibers for the fabrication of bioactive platforms with improved in vitro responses, to be used for innovative therapeutic treatments. Herein, sulfonatocalix[4]arene (SCX4) was synthesized from p-tert-butyl-calix[4]arene and embedded in electrospun nanofibers made of polycaprolactone (PCL) and gelatin (GEL). The supramolecular structure of SCX4 and its efficient entrapment into electrospun fibers was confirmed by NMR spectroscopy and FTIR analysis, respectively. SEM analysis supported via image analysis enabled the investigation of the fiber morphology at the sub-micrometric scale, showing a drastic reduction in fiber diameters in the presence of SCX4: 267 ± 14 nm (without SCX) to 115 ± 5 nm (3% SCX4). Moreover, it was demonstrated that SCX4 significantly contributes to the hydrophilic properties of the fiber surface, as was confirmed by the reduction in contact angles from 54 ± 1.4° to 31 ± 5.5° as the SCX4 amount increased, while no effects on thermal stability were recognized, as was confirmed by TGA analyses. In vitro tests also confirmed that SCX4 is not cytotoxic, but plays a supporting role in L929 interactions, as was validated by the cell viability of PGC15% after 7 days, with respect to the control. These preliminary but promising data suggest their use for the fabrication of innovative platforms able to bind SCX4 to bioactive compounds and molecules for different therapeutic applications, from molecular recognition to controlled drug delivery.

Fabrication of Biocompatible Electrospun Poly(ε-caprolactone)/Gelatin Nanofibers Loaded with Pinus radiata Bark Extracts for Wound Healing Applications

In this study, poly(ε-caprolactone) (PCL)/gelatin (GEL) electrospun nanofibers loaded with two different concentrations of Pinus radiata bark extracts (PEs) were fabricated via electrospinning for wound healing applications. The effects of incorporating PE into PCL/GEL electrospun nanofibers were investigated regarding their physicochemical properties and in vitro biocompatibility. All electrospun nanofibers showed smooth, uniform, and bead-free surfaces. Their functional groups were detected by ATR-FTIR spectroscopy, and their total phenol content was measured by a Folin-Ciocalteu assay. With PE addition, the electrospun nanofibers exhibited an increase in their wettability and degradation rates over time and a decrease in their tensile stress values from 20 ± 4 to 8 ± 2 MPa for PCL/GEL and PCL/GEL/0.36%PE samples, respectively. PE was also released from the fibrous mats in a rather controlled fashion. The PCL/GEL/0.18%PE and PCL/GEL/0.36%PE electrospun nanofibers inhibited bacterial activity at around 6 ± 0.1% and 23 ± 0.3% against E. coli and 14 ± 0.1% and 18 ± 0.2% against S. aureus after 24 h incubation, respectively. In vitro cell studies showed that PE-loaded electrospun nanofibers enhanced HaCaT cell growth, attachment, and proliferation, favoring cell migration towards the scratch area in the wound healing assay and allowing a complete wound closure after 72 h treatment. These findings suggested that PE-loaded electrospun nanofibers are promising materials for antibiotic-free dressings for wound healing applications.

Solution blow spinning of highly deacetylated chitosan nanofiber scaffolds for dermal wound healing

Biocompatible fibrous scaffolds based on highly deacetylated chitosan were fabricated using high-throughput solution blow spinning. Scanning electron microscopy analysis revealed that the chitosan nanofiber scaffolds had ultrafine and continuous fibers (300-1200 nm) with highly interconnected porous structures (30-75% porosity), mimicking some aspects of the native extracellular matrix in skin tissue. Post-treatment of as-spun nanofibers with aqueous potassium carbonate solution resulted in a fibrous scaffold with a high chitosan content that retained its fibrous structural integrity for cell culture. Analysis of the mechanical properties of the chitosan nanofiber scaffolds in both dry and wet conditions showed that their strength and durability were sufficient for wound dressing applications. Significantly, the wet scaffold underwent remarkable elastic deformation during stretch such that the elongation at break dramatically increased to up to 44% of its original length, showing wavy fiber morphology near the break site. The culture of normal human dermal fibroblast cells onto scaffolds for 1-14 days demonstrated that the scaffolds were highly compatible and a suitable platform for cell adhesion, viability, and proliferation. Secretion profiles of wound healing-related proteins to the cell culture medium demonstrated that chitosan fibers were a promising scaffold for wound healing applications. Overall, the dense fibrous network with high porosity of the chitosan nanofiber scaffold and their mechanical properties indicate that they could be used to design and fabricate new materials that mimic the epidermis layer of natural skin.

Environmentally friendly fabrication of electrospun nanofibers made of polycaprolactone, chitosan and κ-carrageenan (PCL/CS/κ-C)

Electrospun fibers based on biodegradable polyanionic or polycationic biopolymers are highly beneficial for biomedical applications. In this work, electrospun nanofibers made from poly(epsilon caprolactone) (PCL), chitosan (CS) and κ-carrageenan (κ-C) were successfully fabricated using several mixtures of benign solvents containing formic acid (FA) and acetic acid (AA). The addition of κ-carrageenan improved the preparation procedure for the production of PCL/CS fibers by electrospinning. Moreover, a polymer mixture was selected to be stored at -20 °C for one month with the purpose to study the properties of the resulting fiber mat. The results indicated that fiber characteristics were not seriously compromised compared to the ones of those fabricated with the original solution, which represents an important reduction in produced waste. Thus, the interactions that occur between positively and negatively charged hydrophilic polysaccharides might induce higher stability to the linear aliphatic polyester in the polymer mixture. All fiber mats were morphologically, physico-chemically and mechanically characterized, showing average fiber diameters in the nano scale. A direct cell viability assay using ST-2 cells demonstrated cell proliferation after 7 days of incubation for all prepared fiber mats, confirming their suitability as potential candidates for bone tissue engineering and wound healing applications.

Study on the Incorporation of Chitosan Flakes in Electrospun Polycaprolactone Scaffolds

Hybrid scaffolds obtained by combining two or more biopolymers are studied in the context of tissue regeneration due to the possibility of achieving new functional properties or structural features. The aim of this work was to produce a new type of hybrid polycaprolactone (PCL)/chitosan (CS) electrospun mat through the controlled deposition of CS flakes interspaced between the PCL fibers. A poly(ethylene oxide) (PEO) solution was used to transport CS flakes with controlled size. This, and the PCL solution, were simultaneously electrospun onto a rotatory mandrel in a perpendicular setup. Different PCL/CS mass ratios were also studied. The morphology of the resulting fibers, evaluated by SEM, confirmed the presence of the CS flakes between the PCL fibers. The addition of PEO/CS fibers resulted in hydrophilic mats with lower Young’s modulus relatively to PCL mats. In vitro cell culture results indicated that the addition of CS lowers both the adhesion and the proliferation of human dermal fibroblasts. The present work demonstrates the feasibility of achieving a controlled deposition of a polymeric component in granular form onto a collector where electrospun nanofibers are being deposited, thereby producing a hybrid scaffold.

State-of-the-Art Review of Electrospun Gelatin-Based Nanofiber Dressings for Wound Healing Applications

Electrospun nanofiber materials have been considered as advanced dressing candidates in the perspective of wound healing and skin regeneration, originated from their high porosity and permeability to air and moisture, effective barrier performance of external pathogens, and fantastic extracellular matrix (ECM) fibril mimicking property. Gelatin is one of the most important natural biomaterials for the design and construction of electrospun nanofiber-based dressings, due to its excellent biocompatibility and biodegradability, and great exudate-absorbing capacity. Various crosslinking approaches including physical, chemical, and biological methods have been introduced to improve the mechanical stability of electrospun gelatin-based nanofiber mats. Some innovative electrospinning strategies, including blend electrospinning, emulsion electrospinning, and coaxial electrospinning, have been explored to improve the mechanical, physicochemical, and biological properties of gelatin-based nanofiber mats. Moreover, numerous bioactive components and therapeutic agents have been utilized to impart the electrospun gelatin-based nanofiber dressing materials with multiple functions, such as antimicrobial, anti-inflammation, antioxidation, hemostatic, and vascularization, as well as other healing-promoting capacities. Noticeably, electrospun gelatin-based nanofiber mats integrated with specific functions have been fabricated to treat some hard-healing wound types containing burn and diabetic wounds. This work provides a detailed review of electrospun gelatin-based nanofiber dressing materials without or with therapeutic agents for wound healing and skin regeneration applications.

Biodegradable blend films of poly(ε-caprolactone)/poly(propylene carbonate) for shelf life extension of whole white button mushrooms

Blend films with poly(ε-caprolactone)(PCL) and poly(propylene carbonate)(PPC)with thickness of approximately 40 μm and 60 μm, respectively, were prepared using a uniaxial-stretching extrusion process to modify the property of PCL. PCL/PPC blend films with better comprehensive properties with thickness about 60 μm were used for equilibrium-modified atmosphere packaging of button mushrooms at 5 °C. The gas barrier property together with water vapor permeability were evaluated as well as its effects on the shelf life button mushrooms. The results showed that the PCL/PPC20 and PCL/PPC50 blend films have suitable gas barrier property and water vapor permeability, which was helpful to generate an appropriate storage environment and more importantly no condensation occurred in these two packages. The lower weight loss of button mushrooms was observed for PCL/PPC20 and PCL/PPC50 blend films 4.43 and 4.46, respectively. The PCL/PPC blend films was more effective in decreasing the activity of PPO and preserving the color of the button mushrooms. The over market acceptability of button mushrooms packaged in PCL/PPC blend films still maintained good and within the limit of marketability after 17 days of storage.

Fabrication of stable electrospun blended chitosan-poly(vinyl alcohol) nanofibers for designing naked-eye colorimetric glucose biosensor based on GOx/HRP

In this study, designing of a stable electrospun blended chitosan (CS)-poly(vinyl alcohol) (PVA) nanofibers for colorimetric glucose biosensing in an aqueous medium was investigated. CS and PVA solutions were blended to acquire an optimum content (CS/PVA:1/4) and electrospunned to obtain uniform and bead-free CS/PVA nanofiber structures following the optimization of the electrospinning parameters (33 kV, 20 cm, and 1.2 ml.h^-1). Crosslinking process applied subsequently provided mechanically and chemically stable nanofibers with an average diameter of 378 nm. The morphological homogeneity, high fluid absorption ability (>%50), thermal (<230 °C) and morphological stability, surface hydrophilicity and degrability properties of cross-linked CS/PVA nanofiber demonstrated their great potential to be developed as an eye-readable strip for biosensing applications. The glucose oxidase (GOx) and horseradish peroxidase (HRP) was immobilized by physical adsorption on the cross-linked CS/PVA nanofiber. The glucose assay analysis by ultraviolet-visible (UV-Vis) spectrophotometry using the same enzymatic system of the proposed glucose strips in form of absorbance versus concentration plot was found to be linear over a glucose concentration range of 2.7 to 13.8 mM. The prepared naked eye colorimetric glucose detection strips, with lower detection limit of 2.7 mM, demonstrated dramatic color change from white (0 mM) to brownish-orange (13.8 mM). The developed cross-linked CS/PVA nanofiber strips, prepared by electrospinnig procedure, could be easily adapted to a color map, as an alternative material for glucose sensing. Design of a practical, low-cost, and environmental-friendly bio-based CS/PVA testing strips for eye readable detection were presented and suggested as an applicable medium for a wide range of glucose concentrations.

S-nitroso human serum albumin as a nitric oxide donor in drug-eluting vascular grafts: Biofunctionality and preclinical evaluation

Currently available synthetic small diameter vascular grafts reveal low patency rates due to thrombosis and intimal hyperplasia. Biofunctionalized grafts releasing nitric oxide (NO) in situ may overcome these limitations. In this study, a drug-eluting vascular graft was designed by blending polycaprolactone (PCL) with S-nitroso-human-serum-albumin (S-NO-HSA), a nitric oxide donor with prolonged half-life. PCL-S-NO-HSA grafts and patches were fabricated via electrospinning. The fabrication process was optimized. Patches were characterized in vitro for their morphology, drug release, biomechanics, inflammatory effects, cell proliferation, and expression of adhesion molecules. The selected optimized formulation (8%PCL-S-NO-HSA) had superior mechanical/morphological properties with high protein content revealing extended NO release (for 28 days). 8%PCL-S-NO-HSA patches significantly promoted endothelial cell proliferation while limiting smooth muscle cell proliferation. Expression of adhesion molecules (ICAM-1, VCAM-1) and pro-inflammatory macrophage/cytokine markers (CD80, IL-1α, TNF-α) was significantly reduced. 8%PCL-S-NO-HSA patches had superior immunomodulatory properties by up-regulating anti-inflammatory cytokines (IL-10) and M2 macrophage marker (CD163) at final time points. Grafts were further evaluated in a small rodent model as aortic implants up to 12 weeks. Grafts were assessed by magnetic resonance imaging angiography (MRI) in vivo and after retrieval by histology. All grafts remained 100 % patent with no signs of thrombosis or calcification. 8%PCL-S-NO-HSA vascular grafts supported rapid endothelialization, whereas smooth muscle cell proliferation was hampered in earlier phases. This study indicates that 8%PCL-S-NO-HSA grafts effectively support long-term in situ release of bioactive NO. The beneficial effects observed can be promising features for long-term success of small diameter vascular grafts. STATEMENT OF SIGNIFICANCE: Despite extensive research in the field of small diameter vascular graft replacement, there is still no appropriate substitute to autografts yet. Various limitations are associated with currently available synthetic vascular grafts such as thrombogenicity and intimal hyperplasia. Therefore, developing new generations of such conduits has become a major focus of research. One of the most significant signaling molecules that are involved in homeostasis of the vascular system is nitric oxide. The new designed nitric-oxide eluting vascular grafts described in this study induce rapid surface endothelialization and late migration of SMCs into the graft wall. These beneficial effects have potential to improve current limitations of small diameter vascular grafts.

A Comparative Analysis of the Structure and Biological Properties of Films and Microfibrous Scaffolds Based on Silk Fibroin

A comparative analysis of the structure and biological properties of silk fibroin constructions was performed. Three groups of constructions were obtained: films obtained by casting an aqueous solution of silk fibroin and electrospun microfibrous scaffolds based on silk fibroin, with the addition of 30% gelatin per total protein weight. The internal structures of the films and single fibers of the microfibrous scaffolds consisted of densely packed globule structures; the surface area to volume ratios and volume porosities of the microfibrous scaffolds were calculated. All constructions were non-toxic for cells and provide high levels of adhesion and proliferation. The high regenerative potential of the constructions was demonstrated in a rat full-thickness skin wound healing model. The constructions accelerated healing by an average of 15 days and can be considered to be promising constructions for various tasks of tissue engineering and regenerative medicine.

Polyurethane-Nanolignin Composite Foam Coated with Propolis as a Platform for Wound Dressing: Synthesis and Characterization

This piece of research explores porous nanocomposite polyurethane (PU) foam synthesis, containing nanolignin (NL), coated with natural antimicrobial propolis for wound dressing. PU foam was synthesized using polyethylene glycol, glycerol, NL, and 1, 6-diisocyanato-hexane (NCO/OH ratio: 1.2) and water as blowing agent. The resultant foam was immersed in ethanolic extract of propolis (EEP). PU, NL-PU, and PU-NL/EEP foams were characterized from mechanical, morphological, and chemical perspectives. NL Incorporation into PU increased mechanical strength, while EEP coating showed lower strength than PU-NL/EEP. Morphological investigations confirmed an open-celled structure with a pore diameter of 150-200 μm, a density of nearly 0.2 g/cm3,, and porosity greater than 85%, which led to significantly high water absorption (267% for PU-NL/EEP). The hydrophilic nature of foams, measured by the contact angle, proved to be increased by NL addition and EEP coating. PU and PU-NL did not show important antibacterial features, while EEP coating resulted in a significant antibacterial efficiency. All foams revealed high biocompatibility toward L929 fibroblasts, with the highest cell viability and cell attachment for PU-NL/EEP. In vivo wound healing using Wistar rats' full-thickness skin wound model confirmed that PU-NL/EEP exhibited an essentially higher wound healing efficacy compared with other foams. Hence, PU-NL/EEP foam could be a promising wound dressing candidate.

Recent advances of emerging green chitosan-based biomaterials with potential biomedical applications: A review

Chitosan is the most abundant natural biopolymer, after cellulose. It is mainly derived from the fungi, shrimp's shells, and exoskeleton of crustaceans, through the deacetylation of chitin. The ecological sustainability associated with its exercise and the flexibility of chitosan owing to its active functional hydroxyl and amino groups makes it a promising candidate for a wide range of applications through a variety of modifications. The biodegradability and biocompatibility of chitosan and its derivatives along with their various chemical functionalities make them promising carriers for pharmaceutical, nutritional, medicinal, environmental, agriculture, drug delivery, and biotechnology applications. The present work aims to provide a detailed and organized description of modified chitosan and its derivatives-based nanomaterials for biomedical applications. We addressed the biological and physicochemical benefits of nanocomposite materials made up of chitosan and its derivatives in various formulations, including improved physicochemical stability and cells/tissue interaction, controlled drug release, and increased bioavailability and efficacy in clinical practice. Moreover, several modification techniques and their effective utilization are also reviewed and collected in this review.

Natural-Based Biomaterial for Skin Wound Healing (Gelatin vs. Collagen): Expert Review

Collagen (Col) and gelatin are most extensively used in various fields, particularly in pharmaceuticals and therapeutics. Numerous researchers have proven that they are highly biocompatible to human tissues, exhibit low antigenicity and are easy to degrade. Despite their different sources both Col and gelatin have almost the same effects when it comes to wound healing mechanisms. Considering this, the bioactivity and biological effects of both Col and gelatin have been, and are being, constantly investigated through in vitro and in vivo assays to obtain maximum outcomes in the future. With regard to their proven nutritional values as sources of protein, Col and gelatin products exert various possible biological activities on cells in the extracellular matrix (ECM). In addition, a vast number of novel Col and gelatin applications have been discovered. This review compared Col and gelatin in terms of their structures, sources of derivatives, physicochemical properties, results of in vitro and in vivo studies, their roles in wound healing and the current challenges in wound healing. Thus, this review provides the current insights and the latest discoveries on both Col and gelatin in their wound healing mechanisms.