Polyethylene/silver-nanofiber composites: A material for antibacterial films

Mechanical Performance of 3D-Printed Polyethylene Fibers and Their Durability against Degradation

Polyethylene (PE), one of the most popular thermoplastic polymers, is widely used in various areas, such as materials engineering and biomedical engineering, due to its superior performance, while 3D printing via fused deposition modeling (FDM) provides a facile method of preparing PE products. To optimize the performance and assess the degradation of FDM-printed PE materials, we systematically investigate the influences of printing parameters, such as fiber diameter (stretching) and printer head temperature, and degradation, such as UV exposure and thermal degradation, on the mechanical performance of FDM-printed PE fibers. When FDM-printed PE fibers with a smaller diameter are prepared under a higher collecting speed, they undergo stronger stretching, and thus, show higher tensile strength and Young's modulus values. Meanwhile, the tensile strength and Young's modulus decrease as the printer head temperature increases, due to the lower viscosity, and thus, weaker shearing at high temperatures. However, degradation, such as UV exposure and thermal degradation, cause a decrease in all four mechanical properties, including tensile strength, Young's modulus, tensile strain and toughness. These results will guide the optimization of FDM-printed PE materials and help to assess the durability of PE products against degradation for their practical application.

In situ degradation of low-density polyethylene film in irrigation maize field: Thickness-dependent effect

Thickness of low-density polyethylene (LDPE) film might determine its mechanical strength, clean production and soil health. Yet, this issue is little understood. In situ aging effects were evaluated in LDPE films with the thickness of 0.006 mm, 0.008 mm, 0.010 mm and 0.015 mm in maize field. The data showed that maximum tensile force (TFmax), maximum tensile strength (TSmax) and elongation at break (EAB) were massively lowered with increasing thickness after aging. The greatest and lowest reduction magnitude of EAB was 27.6 % and 11.2 % in 0.006 mm and 0.015 mm films respectively. Also, the melting point (Tm) and crystallinity (Xc) under Differential Scanning Calorimeter (DSC) tended to decline with the increasing thickness. Moreover, the peak intensity of crystalline regions tended to transfer and concentrate on the amorphous regions, and such tendency became more pronounced in the thin films. Interestingly, there existed a pronounced distinct thickness-dependent effects on soil bulk density (SBD) and soil water-stable aggregate proportion. Thick plastic film mulching increased SBD but reduced the proportion of macroaggregates (mainly referred to 0.015 mm and 0.010 mm). In addition, thick film mulching slightly reduced the levels of soil organic carbon (SOC) and total nitrogen (TN), but significantly promoted the contents of soil labile C and N. Particularly, it significantly promoted above- & under-ground biomass of maize across two growing seasons (p < 0.05). To sum up, thickening LDPE film may act as a promising solution to improve LDPE film residue recycling, while benefiting for higher productivity. However, thick film mulching may cause a certain adverse impact on soil structure, and further investigations would be needed in the future.

Antimicrobial Properties of the Triclosan-Loaded Polymeric Composite Based on Unsaturated Polyester Resin: Synthesis, Characterization and Activity

The manufacturing of sanitary and household furniture on a large scale with inherently antimicrobial properties is an essential field of research. This work focuses on the synthesis of polymer composites based on the unsaturated polyester of resin loaded with 5 wt.%-Triclosan produced by a co-mixing approach on automated technological complex with a potential for broad applications. According to findings, the polymer composite has a non-porous structure (surface area < 1.97 m2/g) suitable for sanitary applications to reduce the growth of bacteria. The chemical composition confirmed the presence of major elements, and the inclusion of Triclosan was quantitatively confirmed by the appearance of chlorine on XRF (1.67 wt.%) and EDS (1.62 wt.%) analysis. Thermal analysis showed the difference of 5 wt.% in weight loss, which confirms the loading of Triclosan into the polymer matrix. The polymer composite completely inhibited the strains of S. aureus 6538-P, S. aureus 39, S. epidermidis 12228, and Kl. Pneumoniae 10031 after 5-min contact time. The antimicrobial effects against Kl. pneumoniae 700603, Ps. aeruginosa 9027 and Ps. aeruginosa TA2 strains were 92.7%, 85.8% and 18.4%, respectively. The inhibition activity against C. albicans 10231 and C. albicans 2091 was 1.6% and 82.4%, respectively; while the clinical strain of C. albicans was inhibited by 92.2%. The polymer composite loaded with 5 wt.%-Triclosan displayed a stability over the period that illustrates the possibility of washing the composite surface.

High-Throughput Fabrication of Antibacterial Starch/PBAT/AgNPs@SiO2 Films for Food Packaging

In this current work, antimicrobial films based on starch, poly(butylene adipate-co-terephthalate) (PBAT), and a commercially available AgNPs@SiO₂ antibacterial composite particle product were produced by using a melt blending and blowing technique. The effects of AgNPs@SiO₂ at various loadings (0, 1, 2, 3, and 4 wt%) on the physicochemical properties and antibacterial activities of starch/PBAT composite films were investigated. AgNPs@SiO₂ particles were more compatible with starch than PBAT, resulting in preferential distribution of AgNPs@SiO₂ in the starch phase. Infusion of starch/PBAT composite films with AgNPs@SiO₂ marginally improved mechanical and water vapor barrier properties, while surface hydrophobicity increased as compared with films without AgNPs@SiO₂. The composite films displayed superior antibacterial activities against both Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria. The sample loaded with 1 wt% AgNPs@SiO₂ (SPA-1) showed nearly 90% inhibition efficiency on the tested microorganisms. Furthermore, a preliminary study on peach and nectarine at 53% RH and 24 °C revealed that SPA-1 film inhibited microbial spoilage and extended the product shelf life as compared with SPA-0 and commercial LDPE packaging materials. The high-throughput production method and strong antibacterial activities of the starch/PBAT/AgNPs@SiO₂ composite films make them promising as antimicrobial packaging materials for commercial application.

Chitosan-Based Nanocomposite Polymeric Membranes for Water Purification-A Review

During the past few years, researchers have focused their attention on developing innovative nanocomposite polymeric membranes with applications in water purification. Natural and synthetic polymers were considered, and it was proven that chitosan-based materials presented important features. This review presents an overview regarding diverse materials used in developing innovative chitosan-based nanocomposite polymeric membranes for water purification. The first part of the review presents a detailed introduction about chitosan, highlighting the fact that is a biocompatible, biodegradable, low-cost, nontoxic biopolymer, having unique structure and interesting properties, and also antibacterial and antioxidant activities, reasons for using it in water treatment applications. To use chitosan-based materials for developing nanocomposite polymeric membranes for wastewater purification applications must enhance their performance by using different materials. In the second part of the review, the performance's features will be presented as a consequence of adding different nanoparticles, also showing the effect that those nanoparticles could bring on other polymeric membranes. Among these features, pollutant's retention and enhancing thermo-mechanical properties will be mentioned. The focus of the third section of the review will illustrate chitosan-based nanocomposite as polymeric membranes for water purification. Over the last few years, researchers have demonstrated that adsorbent nanocomposite polymeric membranes are powerful, important, and potential instruments in separation or removal of pollutants, such as heavy metals, dyes, and other toxic compounds presented in water systems. Lastly, we conclude this review with a summary of the most important applications of chitosan-based nanocomposite polymeric membranes and their perspectives in water purification.

The Role of New Inorganic Materials in Composite Membranes for Water Disinfection

Today, there is an increasing interest in improving the physicochemical properties of polymeric membranes by merging the membranes with different inorganic materials. These so-called composite membranes have been implemented in different membrane-based technologies (e.g., microfiltration, ultrafiltration, nanofiltration, membrane bioreactors, among others) for water treatment and disinfection. This is because such inorganic materials (such as TiO2-, ZnO-, Ag-, and Cu-based nanoparticles, carbon-based materials, to mention just a few) can improve the separation performance of membranes and also some other properties, such as antifouling, mechanical, thermal, and physical and chemical stability. Moreover, such materials display specific biological activity towards viruses, bacteria, and protozoa, showing enhanced water disinfection properties. Therefore, the aim of this review is to collect the latest advances (in the last five years) in using composite membranes and new hybrid materials for water disinfection, paying particular emphasis on relevant results and new hydride composites together with their preparation protocols. Moreover, this review addresses the main mechanism of action of different conventional and novel inorganic materials toward biologically active matter.

Ultrasound-Assisted Preparation, Characterization, and Antibacterial Activity of Montmorillonite Modified by ε-Polylysine Hydrochloride

In this study, two types of antibacterial montmorillonites (Mt) were prepared using a facile method. The Mt modified with ε-polylysine hydrochloride (ε-PL) was named PL-Mt, while the Mt dually modified with dioctadecyl dimethylammonium chloride (D1821) and ε-PL was named PL-OMt. The results of the X-ray diffraction, Fourier-transform infrared (FTIR) spectroscopy and thermogravimetric analysis (TGA) of the PL-Mt indicated that 30% ε-PL was the most suitable amount for intercalating the Mt. The particle size and distribution of the ε-PL in the solution demonstrated that the Mt d-value could not be further increased owing to the increasing ε-PL diameter. The result of the X-ray diffraction of PL-OMt displayed that ultrasonic treatment at 600 W facilitated ε-PL to intercalate into the OMt interlayer space. The PL-OMt prepared with ultrasonic treatment at 600 W exhibited antibacterial activity against Escherichia coli and Bacillus subtilis superior to that of the PL-OMt prepared with higher-power ultrasonic treatment. Thus, the addition of 30% ε-PL based on the dry Mt mass is the most suitable ratio for preparing PL-Mt, while ultrasonic treatment at 600 W is the most suitable for preparing PL-OMt. These findings may expand the application fields of ε-PL.

Electrospun essential oil-polycaprolactone nanofibers as antibiofilm surfaces against clinical Candida tropicalis isolates

OBJECTIVE

As an approach to prevent biofilm infections caused by Candida tropicalis on various surfaces, determination of effect of biodegradable polycaprolactone nanofibers (PCLNFs) with different concentrations of two different essential oils were tested in this study.

RESULTS

Both of the tested essential oils exhibited antifungal effect (minimal inhibitory concentration; 0.25-0.49 µL/mL, minimal fungicidal concentration; 0.25-0.49 µL/mL, depending on the C. tropicalis strain) (Zone of inhibition caused by 500 μL/mL concentration of oils; 28-56 mm). 0, 2, 4% clove oil PCLNFs and 0, 2, 4% red thyme oil-PCLNFs were free from bead formation and uniform in diameter. Diameters of all essential oil containing PCLNFs were ranged from 760 to 1100 nm and were significantly different from 0% essential oil-PCLNF (P < 0.05). 0, 2, 4% clove oil-PCLNFs were significantly more hydrophobic compared to 8% clove oil-PCLNF (P < 0.01), whereas 0% and 2% red thyme oil-PCLNFs were significantly more hydrophobic compared to 4% and 8% red thyme oil PCLNFs (P < 0.01). Highest amount of biofilm inhibition was observed by 4% clove oil-PCLNF and by 4% red thyme oil-PCLNF.

CONCLUSIONS

Clove and red thyme oils may be used not only as antifungals but also as biofilm inhibitive agents on surfaces of biomaterials that are frequently contaminated by C. tropicalis, when they are incorporated into PCLNFs.

Facile preparation and characterization of a nanofiber-coated textile with durable and rechargeable antibacterial activity

A facile and green method was used to prepare a durable and rechargeable antibacterial cotton textile.

Progress of Nanocomposite Membranes for Water Treatment

The use of membrane-based technologies has been applied for water treatment applications; however, the limitations of conventional polymeric membranes have led to the addition of inorganic fillers to enhance their performance. In recent years, nanocomposite membranes have greatly attracted the attention of scientists for water treatment applications such as wastewater treatment, water purification, removal of microorganisms, chemical compounds, heavy metals, etc. The incorporation of different nanofillers, such as carbon nanotubes, zinc oxide, graphene oxide, silver and copper nanoparticles, titanium dioxide, 2D materials, and some other novel nano-scale materials into polymeric membranes have provided great advances, e.g., enhancing on hydrophilicity, suppressing the accumulation of pollutants and foulants, enhancing rejection efficiencies and improving mechanical properties and thermal stabilities. Thereby, the aim of this work is to provide up-to-date information related to those novel nanocomposite membranes and their contribution for water treatment applications.

Preparation and Characterization of Antimicrobial Films Based on LDPE/Ag Nanoparticles with Potential Uses in Food and Health Industries

In this work, the antimicrobial effect of silver nanoparticles in polyethylene based nanocomposites has been investigated using a non-conventional processing method to produce homogeneous materials. High energy ball milling under cryogenic conditions was used to achieve a powder of well-blended low-density polyethylene and commercial silver nanoparticles. The final composites in the form of films were obtained by hot pressing. The effect of various silver nanoparticles content (0, 0.5, 1 and 2 wt %) on the properties of low-density polyethylene and the antimicrobial effectiveness of the composite against DH5α Escherichia coli were studied. The presence of silver nanoparticles did not seem to affect the surface energy and thermal properties of the materials. Apart from the inhibition of bacterial growth, slight changes in the aspect ratio of the bacteria with the content of particles were observed, suggesting a direct relationship between the presence of silver nanoparticles and the proliferation of DH5α E. coli (Escherichia coli) cells. Results indicate that these materials may be used to commercially produce antimicrobial polymers with potential applications in the food and health industries.

New infrared-assisted method for sol-gel derived ZnO:Ag thin films: Structural and bacterial inhibition properties

A new sol-gel method, based on crystallization with Infrared heating, was developed to obtain ZnO:Ag thin films. The common sol, with zinc acetate as precursor and silver nitrate as doping source (1, 3 and 5 % molar), isopropanol and distilled water as solvents and monoethanolamine as stabilizer agent; was modified with Pluronic F127 and diethylene glycol as rheological agents, and with urea as fuel to produce enough energy to the combustion and to promote the crystallization process. Later, Corning glass-substrates were dipped into the sol at a constant speed of 3mms^-1. To provide the necessary energy for obtaining the hexagonal ZnO structure of the coatings during the drying and consolidation process, instead of using the common furnace heat-treatment, the films were heated by means of an infrared (IR) ceramic lamp (800W) for 15, 30, 45, 60 and 180 minutes, and the effect of this annealing method was analyzed. The structural properties were examined by means of X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR), whereas morphology was studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The examination revealed a homogeneous distribution of particles with the characteristic pores of pluronic F127, and the coating roughness had an average value of 100nm by AFM. To evaluate the effect on the number of dipping cycles and the IR-treatment on the thickness, ellipsometry results for 1, 3 and 5 deposits were analyzed and showed increments of 780, 945 and 1082nm, respectively. Finally, to test of the antibacterial activity, instead of the common one-microorganism approach, environmental microorganisms that grow with expose of the broth to the ambient conditions were employed (microbial consortium), which is a real environmental condition. The biological test was carried out by kinetic growth inhibition (optical density) of heterotrophic bacteria in culture liquid media under conditions of light, light-dark and darkness, to analyze the effect of light. A significance reduction in growth was obtained for doped coatings with silver in comparison with the control ZnO substrate. Furthermore, the analysis bacteria growth inhibition on a solid surface showed that the films effectively present antibacterial activity. The best result was obtained with ZnO:Ag 1% in light conditions, about 67%, but all the coatings inhibited the bacterial activity.

Antimicrobial effect of gallium nitrate against bacteria encountered in burn wound infections

The MICs of gallium ions against nine bacteria strains in burn wound infections were determined, and TEM found visual evidence of gallium ions' attacking mechanism.