Preparation and characterization of novel polysulphone hybrid ultrafiltration membranes blended with N-doped GO/TiO 2 nanocomposites

Enhanced filtration membranes with graphene oxide and tannic acid for textile industry wastewater dye removal

A novel modification technique employing a layer-by-layer (LbL) self-assembly method, integrated with a pressure-assisted filtration system, was developed for enhancing a commercial polyethersulfone (PES) microfiltration (MF) membrane. This modification involved the incorporation of tannic acid (TA) in conjunction with graphene oxide (GO) nanosheets. The effectiveness of the LbL method was confirmed through comprehensive characterization analyses, including ATR-FTIR, SEM, water contact angle (WCA), and mean pore size measurements, comparing the modified membrane with the original commercial one. Sixteen variations of PES MF membranes were superficially modified using a three-factorial design, with the deposited amount of TA and GO as key factors. The influence of these factors on the morphology and performance of the membranes was systematically investigated, focusing on parameters such as pure water permeability (PWP), blue corazol (BC) dye removal efficiency, and flux recovery rate (FRR). The membranes produced with the maximum amount of GO (0.1 mg, 0.55 wt%) and TA as the inner and outer layers demonstrated remarkable FRR and significant BC removal, exceeding 80%. Notably, there was no significant difference observed when using either 0.2 (1.11 wt%) or 0.4 mg (2.22 wt%) in the first layer, as indicated by the Tukey mean test. Furthermore, the modified membrane designated as MF/TA0.4GO0.1TA0.4 was evaluated in the filtration of a simulated dye bath wastewater, exhibiting a BC removal efficiency of 49.20% and a salt removal efficiency of 27.74%. In conclusion, the novel PES MF membrane modification proposed in this study effectively enhances the key properties of pressure-driven separation processes.

Effect of different factors on treatment of oily wastewater by TiO2/Al2O3-PVDF ultrafiltration membrane

An ultrafiltration membrane developed by our research group was applied to treat simulated emulsified oil wastewater. ATR-FTIR, SEM, TEM, and Zeta potential analyzes demonstrated that the modified ultrafiltration membrane (MM) has excellent stability and anti-fouling capacity than origin membrane (OM), which possesses a pure water flux of 260 L·m^-2·h^-1 and oil/water (o/w) rejection of 98.5 ± 0.33%. Inorganic salt CaCl₂ has more considerable influence than MgSO₄ and NaCl under the same mass concentration in the two membranes UF process. Along with concentration increasing, flux sharply reduces; meanwhile, the rejection has an opposite trend. Moreover, permeation flux has a maximum value, and the rejection also gets its optimal state under neutral conditions during the pH value of 2-12. The membrane also exhibits excellent anti-fouling performance and anti- o/w adsorption properties with an adsorption rate below 0.8% compared with OM, which has an adsorption rate of nearly 2.1%, respectively. A kind of new UF membrane developed by our research group was applied to treat simulated o/w. ATR-FTIR, SEM, TEM, and Zeta potential analyzes demonstrated that PVDF-Al₂O₃/TiO₂ material has excellent stability and anti-fouling capacity. CaCl₂ has the greatest influence than MgSO₄ and NaCl under the same mass concentration. Moreover, permeation flux has maximum value and the rejection also gets its optimal state under neutral conditions during pH 2-12. The membrane also exhibits excellent anti-fouling performance and anti-O/W adsorption properties with adsorption rate below 0.8% compared with OM which has an adsorption rate nearly 2.1%, respectively.

Bimetallic polyphenol networks structure modified polyethersulfone membrane with hydrophilic and anti-fouling properties based on reverse thermally induced phase separation method

In order to improve the hydrophobicity of traditional polyethersulfone (PES) membranes, this study combined the reverse thermally induced phase separation (RTIPS) method with the constructed bimetallic polyphenol networks (BMPNs) to prepare hydrophilic anti-fouling membranes. As for BMPNs, tannic acid (TA) was served as an intermediate to construct both the inner and surface hydrophilic layers of the PES membranes. On the one hand, etching Zeolitic imidazolate framework-8 (EZIF-8) with synergistic etching and surface functionalization via TA not only retained the high pore structure of MOFs, but also had good hydrophilicity. On the other hand, the MPN hydrophilic layer was formed on the membrane surface by the combination of TA from the surface of EZIF-8 and iron ions in the coagulation bath. Therefore, BMPNs structure penetrated the interior and surface of PES membrane, which greatly improved the hydrophilic properties. In addition, the membrane with porous surfaces and spongy cross sections by RTIPS method improved the permeability and mechanical properties of the membrane by several times compared with the membrane via NIPS method. The obtained membranes in this experiment showed excellent permeability, just like pure water flux reached 1662.16 L/m² h, while BSA rejection rate remained at 92.78%. Compared with pure membrane, it showed a better flux recovery rate (FRR = 83.33%) after cleaning, and the reduction of irreversible (R_ir = 16.67%) fouling indexes indicated that the adsorption of protein was inhibited. These results suggested that the hydrophilic anti-fouling PES membranes prepared by this method possessed great application potential in membrane separation technology.

Preparation and Characterization of Reduced Graphene Oxide /TiO2 Blended Polyphenylene sulfone Antifouling Composite Membrane With Improved Photocatalytic Degradation Performance

Nanosized titanium oxide (TiO2)-based photocatalysts have exhibited great potential for the degradation of organic contaminants, while their weak absorption of visible light limits the photocatalytic efficiency. Herein, a novel reduced graphene oxide/TiO2-polyphenylenesulfone (rGO/TiO2-PPSU) hybrid ultrafiltration membrane has been successfully prepared via a non-solvent induced phase-separation method, in which the synergistic coupling between the rGO and TiO2 could endowed the fabricated membranes with visible-light-driven efficient photocatalytically degradation of organic pollutants and outstanding photocatalytic and antifouling properties. Compared with the PPSU membranes prepared with Graphene oxide and TiO2, respectively, the rGO/TiO2-PPSU membrane demonstrated significant photodegradation towards phenazopyridine hydrochloride (PhP) solution under ultraviolet light (improved about 71 and 43%) and visible light (improved about 153 and 103%). The permeability and flux recovery rates of the membrane indicated that the high flux of the rGO/TiO2-PPSU membrane can be greatly restored after fouling, due to the improved self-cleaning properties under visible light static irradiation. With the properties of high performance of photocatalytic degradation and good self-cleaning ability, the rGO/TiO2-PPSU membrane would have great potential in water treatment.

Investigating the Antibacterial Activity of Polymeric Membranes Fabricated with Aminated Graphene Oxide

A novel, functionalized graphene oxide-based cellulose acetate membrane was fabricated using the phase inversion method to improve the membrane characteristics and performance. We studied the effect of aminated graphene oxide (NH2-GO) composite on the CA membrane characteristics and performance in terms of membrane chemistry, hydrophilicity, thermal and mechanical stability, permeation flux, and antibacterial activity. The results of contact angle and water flux indicate the improved hydrophilic behavior of composite membranes in comparison to that of the pure CA membrane. The AGO-3 membrane showed the highest water flux of about 153 Lm-2h-1. The addition of hydrophilic AGO additive in CA membranes enhanced the antibacterial activity of AGO-CA membranes, and the thermal stability of the resulting membrane also improved since it increases the Tg value in comparison to that of a pristine CA membrane. The aminated graphene oxide (NH2-GO) was, therefore, found to be a promising additive for the fabrication of composite membranes with potent applications in wastewater treatment.

The Use of Polymer Membranes to Counteract the Risk of Environmental of Soil and Water Contamination

Chemical, biological, radiological, or nuclear (CBRN) contamination of the environment is a significant threat to human health and life as well as environmental safety. It is then necessary to take actions aimed at minimizing and eliminating the threat. Depending on the type of contamination, various methods are used, including sorption, biodegradation, separation, or ion exchange processes in which membranes play an important role. The type of membrane is selected in respect of both the environment and the type of neutralized pollutants. Therefore, the production and modification of membranes are being adapted to the type of contamination and the purpose of the work. This article presents examples of membranes and their possible applications depending on the part of the environment subject to reclamation and the type of contamination.

Development of hydrophilic PES membranes using F127 and HKUST-1 based on the RTIPS method: Mitigate the permeability-selectivity trade-off

In this study, to mitigate the permeability-selectivity trade-off effect, Pluronic F127 (F127) and HKUST-1 were employed to construct high-performance membranes based on the reverse thermally induced phase separation (RTIPS) method. F127, as a hydrophilic modifier, was applied to increase permeability and resist polyethersulfone (PES) membrane fouling, while the collapse of HKSUT-1 caused by its instability in pure water improved the permeability and selectivity of the membrane. Characterizations demonstrated the successful synthesis of HKUST-1, together with the successful introduction of HKSUT-1 and F127 in PES membranes. It was observed that the membrane prepared by the RTIPS process possessed a uniformly porous surface and sponge-like cross-section with excellent mechanical properties, higher permeability, and selectivity compared to the dense skin and finger-like cross-section of the membrane prepared by the nonsolvent induced phase separation (NIPS) method. Moreover, the permeation and bovine serum albumin (BSA) rejection rate of the optimal membrane reached 2378 L/m² h and 89.3%, respectively, which were far higher than those of the pure membrane. Hydrophilic F127 and many microvoids formed by the collapse of HKUST-1, played an important role in excellent antifouling properties, high permeability, and selectivity by pure water flux (PWF), flux recovery rate (FRR), BSA flux, and COD removal rate tests. Overall, the membrane with F127 and HKSUT-1 prepared via the RTIPS method not only obtained excellent antifouling properties but also mitigated the permeability-selectivity trade-off.

Fabrication of a Novel Antifouling Polysulfone Membrane with in Situ Embedment of Mxene Nanosheets

Membrane fouling is still a critical issue for the application of ultrafiltration, which has been widely used in water treatment due to its efficiency and simplicity. In order to improve the antifouling property, a new 2D material MXene was used to fabricate composite ultrafiltration membrane with the approach of in situ embedment during the phase inversion process in this study. Scanning electron microscopy (SEM), atomic force microscopy (AFM), thermogravimetric analysis (TGA), energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), water contact angle, bovine serum albumin rejection and porosity measurements were utilized to characterize the prepared membranes. Due to the hydrophilicity of the MXene, the composite membranes obtained higher hydrophilicity, confirmed by the decreased water contact angle. All the modified membranes had a high bovine serum albumin rejection above 90% while that of the pristine polysulfone membrane was 77.48%. The flux recovery ratio and the reversible fouling ratio of the membranes were also improved along with the increasing content of the MXene. Furthermore, the highest flux recovery ratio could also reach 76.1%. These indicated the good antifouling properties of MXene composite membranes. The enhanced water permeability and protein rejection and excellent antifouling properties make MXene a promising material for antifouling membrane modification.

A Membrane Modified with Nitrogen-Doped TiO2/Graphene Oxide for Improved Photocatalytic Performance

An improved photocatalytic microfiltration membrane was successfully prepared by the impregnation method with nitrogen-doped TiO2/graphene oxide (GO) (NTG). By utilizing the unique role of N and GO, the photocatalytic activity of the membrane in UV and sunlight was improved. Compared with the Polyvinylidene Fluoride (PVDF) microfiltration membrane which was modified by TiO2, N-TiO2 (NT) and TiO2-GO (TG), the NTG/PVDF membrane exhibited high photocatalytic efficiency and significantly improved photodegradation power to the methylene blue (MB) solution under ultraviolet light and sunlight, with the photocatalytic efficiency reaching 86.5% and 80.6%, respectively. Scanning electron microscopy (SEM), X-ray diffractometry (XRD) and Fourier transform infrared spectroscopy (FT-IR) were used to analyze the morphology, crystal structure and chemical bonds of the membrane surface. The hydrophilicity of the modified PVDF microfiltration membrane was significantly improved, the flux of the pure water membrane reached 1672 Lm−2h−1, the flux of the MB solution was also significantly improved due to photodegradation. Therefore, the nitrogen-doped titanium dioxide graphene oxide PVDF microfiltration membrane (NTG/PVDF membrane) has great development prospects in sustainable water treatment.

A new analytical device incorporating a nitrogen doped lanthanum metal oxide with reduced graphene oxide sheets for paracetamol sensing

The novel N-CeO₂ nanoparticles decorated on reduced graphene oxide (N-CeO₂@rGO) composite has been synthesized by sonochemical method. The characterization of as prepared nanocomposite was intensely performed by UV-Vis, FT-IR, EDX, FE-SEM, HR-TEM, XRD, and TGA analysis. The synthesized nanomaterial was further investigated for its selective and sensitive sensing of paracetamol (PM) based on a N-CeO₂@rGO modified glassy carbon electrode. A distinct and improved reversible redox peak of PM is obtained at N-CeO₂@rGO nanocomposite compared to the electrodes modified with N-CeO₂ and rGO. It displays a very good performance with a wide linear range of 0.05-0.600 μM, a very low detection limit of 0.0098 μM (S/N = 3), a high sensitivity of 268 μA µM^-1 cm^-2 and short response time (<3 s). Also, the fabricated sensor shows a good sensibleness for the detection of PM in various tablet samples.

Removal of Antibiotics From Water with an All-Carbon 3D Nanofiltration Membrane

Recent industrial developments and increased energy demand have resulted in significantly increased levels of environmental pollutants, which have become a serious global problem. Herein, we propose a novel all-carbon nanofiltration (NF) membrane that consists of multi-walled carbon nanotubes (MWCNTs) interposed between graphene oxide (GO) nanosheets to form a three-dimensional (3D) structure. The as-prepared membrane has abundant two-dimensional (2D) nanochannels that can physically sieve antibiotic molecules through electrostatic interaction. As a result, the prepared membrane, with a thickness of 4.26 μm, shows both a high adsorption of 99.23% for tetracycline hydrochloride (TCH) and a high water permeation of 16.12 L m^- 2 h^- 1 bar^- 1. In addition, the cationic dye methylene blue (MB) was also removed to an extent of 83.88%, indicating broad applications of the prepared membrane.

Titania nanowires coated PEI/P25 membranes for photocatalytic and ultrafiltration applications

Bulk compositing and surface functionalization are combined to achieve a polymeric membrane that is covered with TiO₂ nanowires, which possesses multi-functions of photodegradation, separation and self-cleaning.