The influence of the functional end groups on the properties of polylactide-based materials

MXene-coated piezoelectric poly-L-lactic acid membrane accelerates wound healing by biomimicking low-voltage electrical pulses

Electrical stimulation therapy is effective in promoting wound healing by rescuing the decreased endogenous electrical field, where self-powered and miniaturized devices such as nanogenerators become the emerging trends. While high-voltage and unidirectional electric field may pose thermal effect and damage to the skin, nanogenerators with lower voltages, pulsed or bidirectional currents, and less invasive electrodes are preferred. Herein, we construct a polydopamine (PDA)-modified poly-L-lactic acid (PLLA) /MXene (PDMP/MXene) nanofibrous composite membrane that generates piezoelectric voltages matching the transepithelial potential (TEP) to accelerate wound healing. PDA coating not only enhances the piezoelectricity of PLLA by dipole attraction and alignment, but also increases its hydrophilicity and facilitates subsequent MXene adhesion for electrical conductivity and stability in physiological environment. When applied as wound dressings in mice, the PDMP/MXene membranes act as a nanogenerators with reduced internal resistances and satisfactory piezoelectric performances that resemble bioelectric potentials (~10 mV) responding to physical activities. The membrane significantly accelerates wound closure by facilitating fibroblast migration, collagen deposition and angiogenesis, and suppressing the expression of inflammatory responses. This piezoelectric fibrous membrane therefore provides a convenient solution for speeding up wound healing by sustained low voltage mimicking bioelectricity, better cell affinity.

Chemicals and fuels from lipid-containing biomass: A comprehensive exploration

In response to address the climate crisis, there has been a growing focus on substituting conventional refinery-derived products with those derived from biorefineries. The utilization of lipids as primary materials or intermediates for the synthesis of chemicals and fuels, which are integral to the existing chemical and petrochemical industries, is a key step in this transition. This review provides a comprehensive overview of the production of sustainable chemicals (acids and alcohols), biopolymers, and fuels (including gasoline, kerosene, biodiesel, and heavy fuel oil) from lipids derived from terrestrial and algal biomass. The production of chemicals from lipids involves diverse methods, including polymerization, epoxidation, and separation/purification. Additionally, the transformation of lipids into biofuels can be achieved through processes such as catalytic cracking, hydroprocessing, and transesterification. This review also suggests future research directions that further advance the lipid valorization processes, including enhancement of catalyst durability at harsh conditions, development of deoxygenation process with low H2 consumption, investigation of precise separation of target compounds, increase in lipid accumulation in algal biomass, and development of methods that utilize residues and byproducts generated during lipid extraction and conversion.

Surface Crystal and Degradability of Shape Memory Scaffold Essentialize Osteochondral Regeneration

The minimally invasive deployment of scaffolds is a key safety factor for the regeneration of cartilage and bone defects. Osteogenesis relies primarily on cell-matrix interactions, whereas chondrogenesis relies on cell-cell aggregation. Bone matrix expansion requires osteoconductive scaffold degradation. However, chondrogenic cell aggregation is promoted on the repellent scaffold surface, and minimal scaffold degradation supports the avascular nature of cartilage regeneration. Here, a material satisfying these requirements for osteochondral regeneration is developed by integrating osteoconductive hydroxyapatite (HAp) with a chondroconductive shape memory polymer (SMP). The shape memory function-derived fixity and recovery of the scaffold enabled minimally invasive deployment and expansion to fill irregular defects. The crystalline phases on the SMP surface inhibited cell aggregation by suppressing water penetration and subsequent protein adsorption. However, HAp conjugation SMP (H-SMP) enhanced surface roughness and consequent cell-matrix interactions by limiting cell aggregation using crystal peaks. After mouse subcutaneous implantation, hydrolytic H-SMP accelerated scaffold degradation compared to that by the minimal degradation observed for SMP alone for two months. H-SMP and SMP are found to promote osteogenesis and chondrogenesis, respectively, in vitro and in vivo, including the regeneration of rat osteochondral defects using the binary scaffold form, suggesting that this material is promising for osteochondral regeneration.

Incorporation of Nanostructural Hydroxyapatite and Curcumin Extract from Curcuma longa L. Rhizome into Polylactide to Obtain Green Composite

This study showed that a polylactide (PLA)-based composite filled with nanostructured hydroxyapatite (HAp) and a natural extract from the rhizome of Curcuma longa L. could provide an alternative to commonly used fossil-based plasticsfor food packaging. The incorporation of HAp into the PLA matrix had a positive effect on improving selected properties of the composites; the beneficial effect could be enhanced by introducing a green modifier in the form of an extract. Prior to the fabrication of the composite, the filler was characterized in terms of morphology and composition, and the composite was then fully characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman and Fourier transform infrared spectroscopy (FT-IR), and the mechanical, thermal, thermomechanical, and optical properties were investigated. The proposed material exhibits antioxidant properties against DPPH radicals and antibacterial performance against Escherichia coli (E. coli). The results showed that the nanocomposite has the highest antioxidant and antibacterial properties for 10 wt% HAp with an average diameter of rod-shaped structures below 100 nm. In addition, the introduction of turmeric extract had a positive effect on the tensile strength of the nanocomposites containing 1 and 5% HAp. As the resulting material adsorbs light in a specific wavelength range, it can be used in the medical sector, food-packaging, or coatings.

Insights into heterogeneous surface induced bubble nucleation mechanisms in cellulose reinforced polylactic acid foams

As the most abundant natural homo-polymer, cellulose has the potential to enhance polymer properties reducing the cost of raw materials. In this work, the carboxylate cellulose nanofiber (CNF-C) was selected to modify polylactic acid (PLA) foams, and the density functional theory was constructed to help analyze the foaming mechanism quantitatively. The theoretical results showed that the ordered structure, the carboxyl and the hydroxyl of CNF-C were more conducive to providing much stronger CO2 adsorption for bubble nucleation, where the predicted critical bubble size decreased and the cell density increased with the addition of CNF-C. The experimental results revealed that the CNF-C promoted the rheological properties and crystallization behaviors of PLA samples, the PLA/CNF-C foams were characterized with uniform structures, the average cell size decreased from 21.39 μm to 0.19 μm, and the cell number density increased from 2.65×1010cell/cm3 to 2.30×1014cell/cm3. Those improvements resulted in an increase of 394.0 % for the compressive strength of the prepared foams. Generally, the high-performance PLA/CNF-C foams were fabricated successfully without compromising the properties of bio-based and biodegradable, the foaming mechanism was analyzed combining theoretical results with experimental data, and it was believed to provide a guide for cellulose reinforcing biodegradable polymer materials.

Enhancing the flame retardancy of polylactic acid nonwoven fabric through solvent-free transparent coating

Polylactic acid (PLA) nonwovens, recognized as eco-friendly substitutes for petroleum-based synthetic fibers, face a significant challenge due to their inherent flammability. This work addresses this concern by synthesizing a hyperbranched polyphosphoramide flame retardant (TPDT) through a one-step polycondensation process without using solvent and catalyst. TPDT is subsequently applied to PLA nonwovens using a dip-pad finishing technique. Notably, with a mere 7 wt% weight gain of TPDT, the PLA nonwovens exhibit a substantial increase in the limited oxygen index (LOI) value, reaching 32.3 %. Furthermore, the damaged area in the vertical burning test is reduced by approximately 69.2 %. In the cone calorimeter test, 17 wt% weight gain of TPDT results in a 51.4 % decrease in peak heat release rate and a 56.0 % reduction in total heat release compared to the control PLA. Additionally, char residue increases from 1.5 wt% to 31.1 wt% after combustion. The strong affinity between TPDT and PLA molecules persists even after repeated abrasion, ensuring sustained flame retardancy. Importantly, the introduction of TPDT also imparts increased softness to the PLA nonwovens. This work addresses this concern by synthesizing a hyperbranched polyphosphoramide flame retardant (TPDT) through a solvent-free, catalyst-free, and one-step polycondensation process.

Nanoplastics from disposable paper cups and microwavable food containers

Nanoplastics (NPs, <1 µm) pose greater risks due to their increased absorption rates in biological systems. In this study, we investigated the release of NPs from paper cups and microwavable food containers coated with low-density polyethylene (LDPE) and polylactic acid (PLA). For disposable paper cups, we found that LDPE-coated cups released up to 26-fold more NPs (maximum 1.9 × 107 per cup) than PLA-coated ones. The NPs release from LDPE-coated cups was increased at high temperatures above 80 °C, and further increased by physical agitation. However, negligible NP release was observed when the inner coating thickness exceeded 1 mm. For microwavable food containers, those with PLA coatings were more susceptible to the effects of microwave. Depending on the cooking time, we noticed a significant difference (up to 40000 times) in the number of released NPs between LDPE and PLA coatings. Additionally, higher microwave power level led to an increase of NPs, even with constant total energy input. Considering the release of NP, PLA coatings for disposable paper cups and LDPE coatings for microwavable food containers seem more suitable. Furthermore, our results suggest that multi-use cups significantly reduce NPs release due to their material thickness, making them a safer alternative to disposable ones.

Temperature-Transferable Coarse-Grained Models for Volumetric Properties of Poly(lactic Acid)

A new coarse-grained (CG) model, for which each monomer is mapped as one bead at its center of mass, was developed for simulating the volumetric properties of the polylactide (PLA) bulk. The three bonded CG potentials are first parametrized against the strain energies of the dimer, trimer, and tetramer, and the nonbonded CG potentials are then optimized to match the melt densities of the decamer. With the derived CG potentials, molecular dynamics (MD) simulations are found to reproduce thermal expansion and glass transition. By rescaling the dihedral and nonbonded potentials with temperature-independent factors, the glass transition temperature (Tg) is also satisfactorily restored with little modifications on the volumetric expansive coefficients at both rubbery and glassy states. Therefore, the finally optimized CG potentials exhibit excellent temperature transferability, as rationalized by the Simha-Boyer relation. Furthermore, it is confirmed that the dihedral torsions and nonbonded interactions play key roles in glass transition. Also, the simulated bulk moduli and conformational properties in a wide temperature range compare well with the referenced data. The proposed multiscale scheme has great potential in simulating thermo-mechanical properties of PLA and other polymers.

Synthesis and catalytic performance of wood cellulose nanofibers grafted with polylactic acid in rare-earth complexes based on tetrazole carboxylic acids

Stannous octanoate [Sn(Oct)2] and 4-dimethylamino pyridine (DMAP) were used to catalyze the synthesis of amphiphilic cellulose-based graft copolymers, but the acute toxicity of tin ions and DMAP prompts the need for the application of less harmful catalysts. Herein, green catalyst complexes 1-3 [M(H0.5L)2(H2O)5]·2(H2O) (M = Sm, 1; M = Nd, 2; M = Eu, 3; H2L = 4-(3-(tetrazol-5-yl)pyridin-5-yl)benzoic acid) were synthesized, and their properties were systematically investigated. Single-crystal X-ray diffraction showed that the complexes possessed a zero-dimensional structure, while the thermogravimetry and scanning electron microscopy results confirmed their stability after heating at 110 °C for 10 h. Using complexes 1-3 and DMAP as the catalysts, CNFs were grafted with l-lactide via homogeneous ring-opening polymerization to form wood cellulose nanofibers grafted with l-lactide (WGLAs), and the effects of the ratio of wood cellulose nanofibers (WCNFs) to l-lactide ([AGU]/[LA]) and catalyst dosage were studied. The polymerization followed the coordination-insertion mechanism. Under comparable reaction conditions, the grafting ratio of WGLA-1 reached 84.7 %, and the grafting ratio of complex 1 was found to be higher than those achieved using DMAP. WGLAs demonstrated good thermal stability without cytotoxicity, and the residual catalysts in the WGLAs exhibited fluorescence characteristics. Overall, amphiphilic cellulose-based materials with fluorescence emission offered a promising modification strategy to prepare high-performance polymer composites for agriculture and biomedical application.

Curcumin Co-Encapsulation Potentiates Anti-Arthritic Efficacy of Meloxicam Biodegradable Nanoparticles in Adjuvant-Induced Arthritis Animal Model

This study aimed to evaluate the anti-arthritic activity of curcumin and meloxicam co-loaded PLGA nanoparticles in adjuvant-induced arthritic rats. PLGA nanoparticles encapsulating curcumin (nCur) and meloxicam (nMlx) alone and in combination (nCur/Mlx) were used to characterize zeta size and potential, polydispersity index, encapsulation efficiency (%), compound-polymer interactions (FT-IR analysis), and surface morphology (SEM imaging). In vivo, Complete Freund's adjuvant-induced arthritic rats were intraperitoneally (i.p.) administered with curcumin, meloxicam, curcumin plus meloxicam, nCur, nMlx, and nCur/Mlx for 28 consecutive days. Results showed that nCur, nMlx, and nCur/Mlx significantly (p ≤ 0.05) reduced paw swelling and arthritic score, restored body weight and the immune organ index (thymus and spleen), as well as attenuated serum inflammatory markers (RF, CRP, and PGE2) and oxidative stress parameters (MDA, SOD, and CAT) in adjuvant-induced arthritic rats compared to free compounds. In addition, mono- and dual-compound-loaded nanoparticles significantly (p ≤ 0.05) down-regulated pro-inflammatory cytokines (TNF-α, IL-1β, and IL-6), up-regulated anti-inflammatory cytokines (IL-4, IL-10, and IFN-γ), and modulated OPG and RANKL expressions in paw tissue. The aforementioned results were further confirmed through radiological and histopathological examinations. Furthermore, the anti-arthritic effect of nCur/Mlx was notably (p ≤ 0.05) enhanced compared to nCur or nMlx alone. In conclusion, the co-nanoencapsulation of curcumin could potentiate the anti-arthritic activity of meloxicam and could provide a novel therapeutic approach for the formulation of nanocarrier pharmaceutical products for the management of arthritis.

Osteogenic and antibacterial PLLA membrane for bone tissue engineering

Insufficient bone regeneration and bacterial infection are two major concerns of bone repair materials. Poly-L-lactic acid (PLLA) have been widely used in bone tissue engineering (BTE), however, lack of osteogenic and antibacterial properties have greatly limit its clinical application. Herein, PLLA membrane was firstly treated with polydopamine (PDA), and then modified with ε-polylysine (ε-PL) and alginate (ALG) via layer-by-layer method. The (ε-PL/ALG)n composite layer coated PLLA (PLLA@(ε-PL/ALG)n) could facilitates the adhesion and osteoblast differentiation of MC3T3-E1 cells. Furthermore, PLLA@(ε-PL/ALG)n presents an effective antibacterial efficacy against S. aureus and E. coli, and the bacterial survival rates of S. aureus and E. coli on PLLA@(ε-PL/ALG)10 were 21.5 ± 3.5 % and 13 ± 2.1 %, respectively. This work provides a promising method to design PLLA materials with osteogenic and antibacterial activity simultaneously. Furthermore, the method is also an optional choice to construct multifunctional coatings on the other substrate.

A novel intra-tumoral drug delivery carrier for treatment of oral squamous cell carcinoma

The treatment of oral squamous cell carcinoma (OSCC) includes systemic chemotherapy and is associated with aggressive side effects on patients. This study evaluated a new intra-tumor-targeted drug delivery method for the treatment of OSCC induced on the dorsum of the tongue in white mice. The induced tumors were examined by needle biopsy. A targeted anticancer drug (Cetuximab) and [Cisplatin and 5 Fluorouracil (5-FU)] chemotherapeutic agents were loaded on polyethylene glycol-polylactide-polyethylene glycol (PEG-PLA-PEG) nanoparticles (NPs) designed for intralesional injection while systemic administration was used as control. Fourier transform infrared spectroscopy (FTIR) was performed to study NP chemical structure, a drug release profile was conducted to study release kinetics, and histopathological evaluation was performed before and after treatment to evaluate tissue reactions (n-28, ά = 0.05). The drug release profile was characteristic of the chemotherapeutic agent showing early quick ascend followed by sustained slow release. FTIR peaks identified the polymeric structure of the drug nano-carrier. Histopathologic examination of chemically induced OSCC revealed different grades ranging from non-invasive to invasive stages of OSCC. Intra-tumoral test group revealed significant remission of observed cancer grade compared to the systemically administered group (X² = 12.63, P < 0.001). Finally, using synthesized PEG-PLA-PEG NPs for intralesional injection is a promising route for the treatment of OSCC.

A reaction-diffusion framework for hydrolytic degradation of amorphous polymers based on a discrete chain scission model

Hydrolytic degradation of polymers involves the scission of long chain molecules, leading to molecular weight reduction and mass loss. The precise degradation response however depends on the scission probability of individual bonds along the polymer backbone. In particular, bonds near the chain ends are considered to be more susceptible to hydrolysis than inner bonds. In this paper, we incorporate a discrete chain scission model that can handle arbitrary bond scission probabilities within a continuum reaction-diffusion framework. Overall hydrolysis kinetics (including autocatalysis) is described independently of the chain scission model. By decoupling the description of the chain scission mechanism from kinetics, our framework enables the identification of the chain scission mechanism from molecular weight reduction and mass loss curves commonly reported in experimental degradation studies. We further propose a reduced continuum model which is better suited for large-scale simulations while retaining the predictive capability of the full discrete-continuum model. The model capability is illustrated in representative case studies based on experimental data from the literature for different materials and geometries. STATEMENT OF SIGNIFICANCE: Many models have been proposed to predict the evolution of molecular weight and mass loss in biodegradable polymers undergoing hydrolytic degradation. However, existing models remain limited in their ability to describe the degradation mechanism, autocatalytic kinetics and short chains diffusion simultaneously. Moreover, existing models often rely on empirical relations and a large number of fitting parameters. Here, we propose a conceptually simple discrete-continuum mathematical framework with a small number of parameters which all have a clear physical meaning. Model calibration against experimental data is simplified, and further provides insights into the degradation mechanisms at play, namely random scission, chain-end scission, or a combination of both. The framework can serve as a basis for future generalisations, including a description of evolving crystallinity, or other degradation mechanisms, such as thermal oxidation or photo-degradation.

Synthesis and Characterization of Poly(DL-lactide) Containing Fluorene Structures

9,9-bis[4-(2-hydroxy-3-acryloyloxypropoxy)phenyl]fluorene (BPF) hydroxyl groups (-OH) were used as initiators in the ring-opening polymerization reaction with DL-lactide monomers at different molar ratios to synthesize a Poly(DL-lactide) polymer containing bisphenol fluorene structure and acrylate functional groups (DL-BPF). The polymer's structure and molecular weight range were analyzed using NMR (¹H, ¹³C) and gel permeation chromatography. DL-BPF was then subjected to photocrosslinking using the photoinitiator Omnirad 1173, resulting in the formation of an optically transparent crosslinked polymer. Characterization of the crosslinked polymer involved analyzing its gel content, refractive index, thermal stability (via differential scanning thermometry (DSC) and thermogravimetric analysis (TGA)), as well as conducting cytotoxicity tests. The crosslinked copolymer exhibited a maximum refractive index of 1.5276, a maximum glass transition temperature of 61.1 °C, and cell survival rates higher than 83% in the cytotoxicity tests.

Construction of highly ductile, UV-shielding polylactide/poly(butylene adipate-co-terephthalate) biocomposites with hyperbranched polysiloxane functionalized lignin as a biocompatibilizer

Biodegradable polylactide/poly(butylene adipate-co-terephthalate) (PLA/PBAT) blends have been widely utilized as packaging materials. However, it is urgent to develop a biocompatibilizer to improve the interfacial interaction of the biodegradable immiscible polymer blends in practice. In this paper, a novel type of hyperbranched polysiloxane (HBPSi) with terminal methoxy groups was synthesized and then utilized to functionalize lignin through a hydrosilation reaction. The HBPSi modified lignin (lignin@HBPSi) was incorporated into immiscible PLA/PBAT blends to serve as a biocompatibilizer. The lignin@HBPSi was uniformly dispersed in the PLA/PBAT matrix with improved interfacial compatibility. Dynamic rheological results revealed that the addition of lignin@HBPSi reduced the complex viscosity, improving the processing ability of the PLA/PBAT composite. The PLA/PBAT composite containing 5 wt% lignin@HBPSi had a superior toughness with an elongation at break of 300.2 % and a slight enhancement in tensile stress (34.47 MPa). In addition, the presence of lignin@HBPSi contributed to blocking ultraviolet rays in the full ultraviolet band. This work provides a feasible way to develop highly ductile PLA/PBAT/lignin composites with good UV-shielding properties for the packaging applications.

Highly Stable Docetaxel-Loaded Nanoparticles Based on Poly(D,L-lactide)-b-Poly(ethylene glycol) for Cancer Treatment: Preparation, Characterization, and In Vitro Cytotoxicity Studies

Stability and narrow size distribution are among the main requirements that apply to drug formulations based on polymeric nanoparticles. In this study, we obtained a series of particles based on biodegradable poly(D,L-lactide)-b-poly(ethylene glycol) (P(D,L)LA_n-b-PEG₁₁₃) copolymers with varied hydrophobic P(D,L)LA block length n from 50 to 1230 monomer units stabilized by poly(vinyl alcohol) (PVA) by a simple "oil-in-water" emulsion method. We found that nanoparticles of P(D,L)LA_n-b-PEG₁₁₃ copolymers with relatively short P(D,L)LA block (n ≤ 180) are prone to aggregate in water. P(D,L)LA_n-b-PEG₁₁₃ copolymers with n ≥ 680 can form spherical unimodal particles with values of hydrodynamic diameter less than 250 nm and polydispersity less than 0.2. The aggregation behavior of P(D,L)LA_n-b-PEG₁₁₃ particles was elucidated in terms of tethering density and conformation of PEG chains at the P(D,L)LA core. Docetaxel (DTX) loaded nanoparticles based on P(D,L)LA₆₈₀-b-PEG₁₁₃ and P(D,L)LA₁₂₃₀-b-PEG₁₁₃ copolymers were formulated and studied. It was observed that DTX-loaded P(D,L)LA_n-b-PEG₁₁₃ (n = 680, 1230) particles are characterized by high thermodynamic and kinetic stability in aqueous medium. The cumulative release of DTX from the P(D,L)LA_n-b-PEG₁₁₃ (n = 680, 1230) particles is sustained. An increase in P(D,L)LA block length results in a decrease in DTX release rate. The in vitro antiproliferative activity and selectivity studies revealed that DTX-loaded P(D,L)LA₁₂₃₀-b-PEG₁₁₃ nanoparticles demonstrate better anticancer performance than free DTX. Favorable freeze-drying conditions for DTX nanoformulation based on P(D,L)LA₁₂₃₀-b-PEG₁₁₃ particles were also established.

Toward ultra-tough and heat-resistant biodegradable polylactide/core-shell rubber blends by regulating the distribution of rubber particles with stereocomplex crystallites

Ultra-tough and heat-resistant poly(l-lactide)/core-shell rubber (PLLA/CSR) blends were fabricated by utilizing stereocomplex (SC) crystallites to effectively regulate the CSR distribution in PLLA matrix. Linear and 3-11 armed poly(d-lactide)s (PDLAs) were synthesized and then melt-mixed with PLLA/CSR blend. Interestingly, the incorporated PDLA chains could collaborate with PLLA chains to form dense SC crystallites network in PLLA/PDLA/CSR blends, thus inducing the CSR particles to transform from uniform distribution structure to network-like structure. With increasing the PDLA arm numbers, the size of CSR clusters in the network-like structure first increased and then decreased, and the continuity of the network-like structure first remained at a high level and then decreased obviously. The formation of CSR network-like structure could remarkably improve the impact strength of PLLA/PDLA/CSR blends without deteriorating their strength and modulus (compared with PLLA/CSR blend), and the CSR network-like structure with larger-sized CSR clusters and higher continuity could help obtain higher impact strength (78.3 kJ/m²). Moreover, the heat resistance of PLLA/PDLA/CSR blends could also be significantly improved (the highest Vicat softening temperature was 131 °C) by the SC crystallites network and CSR network-like structure. This work provides an effective strategy for controlling the rubber network-like morphology and thereby preparing high-performance PLLA materials.

Thiophene End-Functionalized Oligo-(D,L-Lactide) as a New Electroactive Macromonomer for the "Hairy-Rod" Type Conjugated Polymers Synthesis

The development of the modern society imposes a fast-growing demand for new advanced functional polymer materials. To this aim, one of the most plausible current methodologies is the end-group functionalization of existing conventional polymers. If the end functional group is able to polymerize, this method enables the synthesis of a molecularly complex, grafted architecture that opens the access to a wider range of material properties, as well as tailoring the special functions required for certain applications. In this context, the present paper reports on α-thienyl-ω-hydroxyl-end-groups functionalized oligo-(D,L-lactide) (Th-PDLLA), which was designed to combine the polymerizability and photophysical properties of thiophene with the biocompatibility and biodegradability of poly-(D,L-lactide). Th-PDLLA was synthesized using the path of "functional initiator" in the ring-opening polymerization (ROP) of (D,L)-lactide, assisted by stannous 2-ethyl hexanoate (Sn(oct)₂). The results of NMR and FT-IR spectroscopic methods confirmed the Th-PDLLA's expected structure, while the oligomeric nature of Th-PDLLA, as resulting from the calculations based on ¹H-NMR data, is supported by the findings from gel permeation chromatography (GPC) and by the results of the thermal analyses. The behavior of Th-PDLLA in different organic solvents, evaluated by UV-vis and fluorescence spectroscopy, but also by dynamic light scattering (DLS), suggested the presence of colloidal supramolecular structures, underlining the nature of the macromonomer Th-PDLLA as an "shape amphiphile". To test its functionality, the ability of Th-PDLLA to work as a building block for the synthesis of molecular composites was demonstrated by photoinduced oxidative homopolymerization in the presence of diphenyliodonium salt (DPI). The occurrence of a polymerization process, with the formation of a thiophene-conjugated oligomeric main chain grafted with oligomeric PDLLA, was proven, in addition to the visual changes, by the results of GPC, ¹H-NMR, FT-IR, UV-vis and fluorescence measurements.

Comparison of polylactic acid biodegradation ability of Brevibacillus brevis and Bacillus amyloliquefaciens and promotion of PLA biodegradation by soytone

Polylactic acid (PLA), a biodegradable plastic, is used to substitute commercial plastics in various fields such as disposable packaging materials and mulching films. Although the biodegradation of PLA under submerged or composting conditions is accelerated, increasing the biodegradability of PLA under soil burial conditions is still a challenge. This study reviews and compares the PLA biodegradation ability of Bacillus amyloliquefaciens and Brevibacillus brevis, both PLA-degrading bacteria. The biodegradation ability of a single bacteria in non-composting conditions was evaluated. In addition, in terms of biostimulation, PLA biodegradation according to nitrogen sources was compared. As a result, a higher PLA biodegradation ability was found in B. brevis than in B. amyloliquefaciens. Moreover, it was confirmed that the biodegradation of the PLA film was increased by using soytone as a nitrogen source in both bacteria. Controlling the nitrogen source could be a new way to increase the biodegradation of PLA.