Sampling trace organic compounds in water: a comparison of a continuous active sampler to continuous passive and discrete sampling methods

Evaluating Solid Phase Adsorption Toxin Tracking (SPATT) for passive monitoring of per- and polyfluoroalkyl substances (PFAS) with Ion Mobility Spectrometry-Mass Spectrometry (IMS-MS)

Detection and monitoring of per- and polyfluoroalkyl substances (PFAS) in aquatic environments has become an increasingly higher priority of regulatory agencies as public concern for human intake of these chemicals continues to grow. While many methods utilize active sampling strategies ("grab samples") for precise PFAS quantitation, here we evaluate the efficacy of low-cost passive sampling devices (Solid Phase Adsorption Toxin Tracking, or SPATTs) for spatial and temporal PFAS assessment of aquatic systems. For this study, passive samplers were initially deployed in North Carolina along the Cape Fear River during the summer and fall of 2016 and 2017. These were originally intended for the detection of microcystins and monitoring potentially harmful algal blooms, though this period also coincided with occurrences of PFAS discharge from a local fluorochemical manufacturer into the river. Additional samplers were then deployed in 2022 to evaluate changes in PFAS fingerprint and abundances. Assessment of PFAS showed legacy compounds were observed across almost all sampling sites over all 3 years (PFHxS, PFOS, PFHxA, etc.), while emerging replacement PFAS (e.g., Nafion byproducts) were predominantly localized downstream from the manufacturer. Furthermore, samplers deployed downstream from the manufacturer in 2022 noted sharp decreases in observed signal for replacement PFAS in comparison to samplers deployed in 2016 and 2017, indicating mitigation and remediation efforts in the area were able to reduce localized fluorochemical contamination.

Evaluation of ceramic passive samplers using a mixed-mode strong cation-exchange sorbent to monitor polar contaminants in river water

Although most of the analytical methods developed for the monitoring of contaminants in environmental waters are based on discrete grab sampling, an alternative of increasing interest is the use of passive sampling. Methods based on passive sampling provide the sampling and pre-concentration of the analytes in-situ, which makes the sample treatment less time consuming and costly than using discrete grab sampling. In this study, ceramic passive samplers (CPSs) using mixed-mode strong cation-exchange sorbent (Oasis MCX) as retention phase were evaluated for the determination of a group of 21 therapeutic and illicit drugs and some of their metabolites in river water samples that were determined by liquid chromatography-tandem mass spectrometry. After assessing the stability of the analytes, the CPSs were calibrated for 9 days with bottled water and river water, obtaining, for the 19 stable compounds, sample rates (Rs) ranging between 0.180 and 1.767 mL/day and diffusion coefficients (De) between 2.02E-8 and 2.81E-7 cm2/s. Once calibrated, CPSs were deployed for the determination of contaminants in the Ebre River, with good reproducibility, and some of the analytes were determined, including amongst others, gabapentin at 76 ng/L, caffeine at 203 ng/L or diclofenac amine at 57 ng/L. The passive sampling method herein presented is simple and feasible and allows the time-integrated analysis of pharmaceuticals and drugs at trace levels in river water. This study opens the possibility of using other mixed-mode sorbents or other types of sorbents as retaining phase on CPSs for the determination of very polar contaminants in water.

Non-targeted and suspect screening analysis using ion exchange chromatography-Orbitrap tandem mass spectrometry reveals polar and very mobile xenobiotics in Danish drinking water

Non-targeted and suspect screening analysis is gaining approval across the scientific and regulatory community to monitor the chemical status in the environment and thus environmental quality. These holistic screening analyses provides the means to perform suspect screening and go beyond to discover previously undescribed chemical pollutants in environmental samples. In a case study, we developed and optimized a high-resolution tandem mass spectrometry platform hyphenated with anion exchange chromatography to screen drinking water samples in Denmark. The optimized non-targeted screening method was able to detect anionic and polar compounds and was successfully applied to drinking water from two drinking water facilities. Following a data analysis pipeline optimization, anionic pesticide residues and other environmental contaminants were detected at confidence identification level 1 such as dimethachlor ESA, mecoprop, and dichlorprop in drinking water. In addition to these three substances, it was possible to detect another 1662 compounds, of which 97 were annotated at confidence identification level 2. More research is urgently needed to health risk prioritize the detected substances and to determine their concentrations.

Compact and automated eDNA sampler for in situ monitoring of marine environments

Using environmental DNA (eDNA) to monitor biodiversity in aquatic environments is becoming an efficient and cost-effective alternative to other methods such as visual and acoustic identification. Until recently, eDNA sampling was accomplished primarily through manual sampling methods; however, with technological advances, automated samplers are being developed to make sampling easier and more accessible. This paper describes a new eDNA sampler capable of self-cleaning and multi-sample capture and preservation, all within a single unit capable of being deployed by a single person. The first in-field test of this sampler took place in the Bedford Basin, Nova Scotia, Canada alongside parallel samples taken using the typical Niskin bottle collection and post-collection filtration method. Both methods were able to capture the same aquatic microbial community and counts of representative DNA sequences were well correlated between methods with R[Formula: see text] values ranging from 0.71-0.93. The two collection methods returned the same top 10 families in near identical relative abundance, demonstrating that the sampler was able to capture the same community composition of common microbes as the Niskin. The presented eDNA sampler provides a robust alternative to manual sampling methods, is amenable to autonomous vehicle payload constraints, and will facilitate persistent monitoring of remote and inaccessible sites.

A new monitoring approach for sustainability assessment of subsurface utilities gasket materials against gasoline and chlorinated solvents: Field evaluation and model development

Once installed, underground concrete pipes with rubber gaskets might be exposed to contaminated soil and groundwater. A pipe material monitoring capsule (PMMC) has been developed to evaluate volatile organic compounds (VOCs) breaking through three types of pipe gaskets; Neoprene, Buna-N, and Viton. The PMMCs were deployed in three contaminated sites: two with gasoline and one with chlorinated solvent (CS). A 3-D field-domain numerical model has been developed for each site to calibrate equivalent hydraulic parameters of each gasket material (k_e, D) against benzene and PCE diffusion. The calibrated parameters were then used to compute the concentrations as well as rate of breakthrough of the two study contaminants. A protocol was developed for installing/retrieval of PMMCs to monitor PCE and benzene mass breaking through the gasket material with time. Employing PMMC, benzene concentrations breaking through the Neoprene and Buna-N after 4 months were approximately 70% and 60% respectively of the monitoring wells concentration. The corresponding value for PCE breakthrough after 4 months was 60% for both the Neoprene and Buna-N. Both gasket materials of Neoprene and Buna-N yielded similar performances, including higher rate of contaminant breakthrough compared to Viton. A nonlinear relationship of mass breaking through the gaskets of benzene and PCE with time was discerned from the modeling and field data.

Understanding and managing uncertainty and variability for wastewater monitoring beyond the pandemic: Lessons learned from the United Kingdom national COVID-19 surveillance programmes

The COVID-19 pandemic has put unprecedented pressure on public health resources around the world. From adversity, opportunities have arisen to measure the state and dynamics of human disease at a scale not seen before. In the United Kingdom, the evidence that wastewater could be used to monitor the SARS-CoV-2 virus prompted the development of National wastewater surveillance programmes. The scale and pace of this work has proven to be unique in monitoring of virus dynamics at a national level, demonstrating the importance of wastewater-based epidemiology (WBE) for public health protection. Beyond COVID-19, it can provide additional value for monitoring and informing on a range of biological and chemical markers of human health. A discussion of measurement uncertainty associated with surveillance of wastewater, focusing on lessons-learned from the UK programmes monitoring COVID-19 is presented, showing that sources of uncertainty impacting measurement quality and interpretation of data for public health decision-making, are varied and complex. While some factors remain poorly understood, we present approaches taken by the UK programmes to manage and mitigate the more tractable sources of uncertainty. This work provides a platform to integrate uncertainty management into WBE activities as part of global One Health initiatives beyond the pandemic.

Development and evaluation of a ceramic diffusive layer based DGT technique for measuring organic micropollutants in seawaters

Diffusive gradients in thin-films (DGT) technique has been well demonstrated as a robust tool for measuring organic micropollutants (OMPs) in the aquatic environment. However, potential adsorption of the OMPs on organic polymer filters and flow rate of waters can affect the measuring results of the DGT method, hence tedious work should be conducted to reduce these interferences. In the present study, a novel DGT technique coupled with a ceramic diffusive layer was developed to measure the OMPs in seawaters. The ceramic diffusive layer exhibited adsorption inertness to the OMPs with various logK_ow values. Moreover, the ceramic diffusive layer based DGT technique was proved to be less affected by the flow rate than the traditional DGT with agarose diffusive layer. The developed DGT device exhibited kinetic accumulation for the targets during a 6-d deployment, and measurement of the OMPs by the DGT method was independent with pH and ionic strength. Finally, the developed DGT sampler was applied in coastal waters of Dalian, and eight OMPs were detected with levels ranging from 1.58 to 13.1 ng/L. The development of the ceramic diffusive membrane can lead to simplification of the DGT applications, promoting the progress of the OMPs monitoring technology.

Environmental Footprint of Wastewater Treatment: A Step Forward in the Use of Toxicological Tools

The assessment of the actual impact of discharged wastewater on the whole ecosystem and, in turn, on human health requires the execution of bioassays. In effect, based on the chemical characterization alone, the synergistic/antagonistic effect of mixtures of pollutants is hardly estimable. The aim of this work was to evaluate the applicability of a battery of bioassays and to suggest a smart procedure for results representation. Two real wastewater treatment plants were submitted to analytical campaigns. Several baseline toxicity assays were conducted, together with tests for the determination of endocrine activity, genetic toxicity and carcinogenicity of wastewater. A “traffic light” model was adopted for an easy-to-understand visualization of the results. Although the legal prescriptions of chemical parameters are fully complied with, bioassays show that a certain biological activity still residues in the treated effluents. Moreover, influent and effluent responses are not always appreciably different. Some tests employing human cells were revealed to be only partially adequate for environmental applications. An interesting and helpful development of the present approach would consist in the estimation of biological equivalents of toxicity, as shown for the estrogenic compound 17-β-estradiol.

External trap-and-release membrane inlet for photoionization mass spectrometry: Towards fast direct analysis of aromatic pollutants in aquatic systems

RATIONALE

Fast and sensitive detection of aromatic hydrocarbons (AHs) in water is of high importance because of their significant impact on human health and the environment. For this, resonance-enhanced multiphoton ionization (REMPI) coupled to trap-and-release membrane-introduction mass spectrometry (T&R-MIMS) offers the possibility of sensitive on-line water analysis with a time resolution of minutes.

METHODS

REMPI is a versatile tool for sensitive gas-phase analysis, in which AHs are selectively ionized in complex gas mixtures by the subsequent absorption of at least two photons. In T&R-MIMS, selective extraction and enrichment of analytes from water can be achieved using semipermeable membranes. By the subsequent stimulated desorption of enriched compounds, mass spectrometric detection is enabled.

RESULTS

We present an external T&R inlet for hollow-fiber membranes coupled to REMPI time-of-flight mass spectrometry, which enables direct and sensitive detection of semi-volatile AHs in water. In laboratory experiments, spiked water samples were analyzed. For the investigated compounds, limits of detection (LODs) in the range 1-47 ng/L were determined. The LODs are approximately one order of magnitude lower than in a previously reported continuous membrane-introduction approach using a planar membrane. Further improvement of LOD may be realized by extending the trapping time and by increasing the release temperature. Furthermore, the system was applied to investigate different fuels suspended in water and real water samples. The obtained data are in good agreement with findings of a former study.

CONCLUSIONS

In the framework of the present study, we demonstrate the high potential of the combination of REMPI and T&R-MIMS in the form of a newly developed external hollow-fiber membrane inlet. With the developed system, semi-volatile AHs can be directly detected down to ng/L levels on a minute time scale. The approach thus may pave the way to future ship application in marine sciences, natural resources exploration or pollutant and hazard detection.

A year-long passive sampling of phenolic endocrine disrupting chemicals in the East River, South China

The occurrence of endocrine disrupting chemicals (EDCs) in the aquatic environment is a global concern. In this study, we employed two different passive samplers Diffusive Gradients in Thin-films (DGT) and Chemcatcher for in situ measurement of 8 phenolic EDCs in the East River of the Pearl River system over one-year. These data were assessed alongside results from traditional grab sampling. Six chemicals (4tOP, 4NP, BPA, E1, EE2 and DES) were regularly detected in the water samples, of which the three phenols (i.e. 4tOP, 4NP and BPA) were in all samples and at high concentrations (0.4-1040 ng/L for 4tOP, 2.6-58500 ng/L for NP and 11.4-123300 ng/L for BPA). Fewer target chemicals were detected in both passive samplers, with only 4tOP, 4NP and BPA found in most samplers; E1 and DES were occasionally measurable above detection limits. The higher (by about a factor of 2-3) measurements provided by DGT compared to Chemcatcher could be attributed to the effect of the diffusive boundary layer on Chemcatcher uptake or the strong adsorption of target chemicals on the Chemcatcher PES filter. The temporal trends of EDC monthly loadings indicated that they were from different sources and that WWTPs were not effective in EDC removal and/or there was still some untreated wastewater discharged into the rivers.

Legacy and current pesticide residues in Syr Darya, Kazakhstan: Contamination status, seasonal variation and preliminary ecological risk assessment

The Syr Darya is one of two major rivers in Central Asia supplying critical fresh water to the Aral Sea. In spite of the river's importance and agriculturally-intensive history, few studies have provided a modern evaluation of and the occurrence of pesticide residues potential effects to aquatic life. The primary goal of this investigation was to determine seasonal variations in ambient concentrations of modern and legacy pesticides in bottom sediment and water of the Syr Darya in Kazakhstan (KZ) downstream from an agriculturally-intensive watershed in Uzbekistan. Grab samples and passive samplers were used at five remote sampling stations during June 2015 to provide a baseline for ecotoxicological evaluation. Results were compared with samples collected during and after the agricultural growing season. Polar organic chemical integrative samplers (POCIS) were used in June and calibrated for time-weighted average concentrations of current use pesticides. Among legacy chlorinated pesticides measured in grab samples from the river, lindane (γ-HCH) was detected most frequently with the highest concentrations occurring during June. For all the sampling events, residues of lindane (γ-HCH) ranged from 0.014 to 0.24 μg/L detected in water samples, are among the highest concentrations reported for rivers globally. Concentrations of γ-HCH, p,p'-DDE and dieldrin were highest in October when dieldrin concentrations approached 0.4 μg/L. Sources of legacy pesticides may be either illicit upstream use or evidence of previous atmospheric contamination of glacial meltwater. Chronic exposure to these residues may lead to ecological risk to lower order organisms in both the sediment and water column.

Characterization of the accumulation of metals and organic contaminants on a novel active-passive sampling device under controlled water flow conditions

Recently, a new sampling device combining active and passive sampling (APS) was developed for the measurement of time-averaged concentrations of metal species and both polar and non-polar organic contaminants in water. By coupling a diffusion cell (loaded with a set of sorbents selective for different substances) with a small pump and a flow meter, the APS device is able to perform in situ measurements that are independent of the hydrodynamic conditions in the exposure medium. In the present study, the diffusion layer thickness (δ) at the sorbent/solution interface within the diffusion cell was characterised under controlled flow conditions. Laboratory tests indicated that, in the range of flow rates investigated, the average diffusion layer thickness (δ¯) varied from ∼60 to ∼110 μm, depending on the type of substance measured and the position of the sorbent with respect to the flow direction. Due to its ability to maintain an approximately constant δ¯, good to excellent agreement was found between measurements performed with the APS device in non-complexing media and concentrations measured in discrete water samples for all the substances investigated. These results suggest that the APS device could overcome issues affecting the quantitative interpretation of measurements by conventional passive sampling devices and serve as a useful tool for simultaneously monitoring a wide range of contaminants in water.

Release of Munitions Constituents in Aquatic Environments Under Realistic Scenarios and Validation of Polar Organic Chemical Integrative Samplers for Monitoring

Munitions constituents (MC) may be released into aquatic environments as a result of underwater military munitions (UWMM) corrosion and breach. The present study investigated the release of 2,4,6-trinitrotoluene (TNT) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) from Composition B fragments under 2 realistic exposure scenarios in a large flume with flow set at 15 cm/s: the first represented the release of MC from fully exposed Composition B, and the second represented release through a small hole, simulating a breached munition. Release of MC through a small hole was approximately 10 times lower than from exposed Composition B, demonstrating the strong influence of exposure to flow on release. The rate of release of MC into the flume was similar to that previously reported in a related field experiment, but a similar mass loss resulted in MC concentration in the field >300 times lower, likely by the dilution effect of hydrodynamic transport. The present study corroborates previous findings of release of MC at UWMM sites resulting in concentrations below the toxicity threshold to most species. In the flume water, MC was quantified using frequent grab sampling and polar organic chemical integrative samplers (POCIS). For TNT, POCIS-estimated time-weighted average concentrations were up to 40% higher than those derived from grab samples, whereas for RDX differences were 6% or less, demonstrating that POCIS provide reliable temporal integration of changing environmental concentrations for common MC. Environ Toxicol Chem 2019;38:2383-2391. Published 2019 Wiley Periodicals Inc. on behalf of SETAC. This article is a US government work and, as such, is in the public domain in the United States of America.

A Novel Active Sampler Coupling Osmotic Pump and Solid Phase Extraction for in Situ Sampling of Organic Pollutants in Surface Water

Active samplers for ambient monitoring of trace contaminants in surface water are highly desirable, but their use is often constrained by power supply. Here, we proposed a novel solution by coupling an improved osmotic pump (OP) with a solid-phase extraction (SPE) cartridge to construct a power-free active sampler for organic contaminants. The OP simply consisted of two cylindrical chambers separated by a reverse osmosis membrane. We, for the first time, added ion-exchange resins into the OP inlet chamber and successfully constructed OPs with a smooth and constant flow. In the OP-SPE sampler, water was continuously drawn through the SPE cartridge at a constant flow, and time-weighted average concentration over the sampling course may be easily calculated from the amount of target analytes retained on the SPE cartridge and water collected in the sampler. The OP-SPE samplers were deployed in a river to detect herbicides, and the measured concentrations were largely in agreement with the average of 11 daily spot samples. Given that a wide range of SPE cartridges are available for different classes of organic contaminants, this approach is versatile and may find widespread applications for in situ sampling of surface water under different conditions, including poorly accessible locations.

Continuous low-level aquatic monitoring (CLAM) samplers for pesticide contaminant screening in urban runoff: Analytical approach and a field test case

Monitoring of surface waters for organic contaminants is costly. Grab water sampling often results in non-detects for organic contaminants due to missing a pulse event or analytical instrumentation limitations with a small sample size. Continuous Low-Level Aquatic Monitoring (CLAM) samplers (C.I.Agent^® Solutions) continually extract and concentrate organic contaminants in surface water onto a solid phase extraction disk. Utilizing CLAM samplers, we developed a broad spectrum analytical screen for monitoring organic contaminants in urban runoff. An intermediate polarity solid phase, hydrophobic/lipophilic balance (HLB), was chosen as the sorbent for the CLAM to target a broad range of compounds. Eighteen urban-use pesticides and pesticide degradates were targeted for analysis by LC/MS/MS, with recoveries between 59 and 135% in laboratory studies. In field studies, CLAM samplers were deployed at discrete time points from February 2015 to March 2016. Half of the targeted chemicals were detected with reporting limits up to 90 times lower than routine 1-L grab samples with good precision between field replicates. In a final deployment, CLAM samplers were compared to 1-L water samples. In this side-by-side comparison, imidacloprid, fipronil, and three fipronil degradates were detected by the CLAM sampler but only imidacloprid and fipronil sulfone were detected in the water samples. However, concentrations of fipronil sulfone and imidacloprid were significantly lower with the CLAM and a transient spike of diuron was not detected. Although the CLAM sampler has limitations, it can be a powerful tool for development of more focused and informed monitoring efforts based on pre-identified targets in the field.

Assessment of a novel device for onsite integrative large-volume solid phase extraction of water samples to enable a comprehensive chemical and effect-based analysis

The implementation of targeted and nontargeted chemical screening analysis in combination with in vitro and organism-level bioassays is a prerequisite for a more holistic monitoring of water quality in the future. For chemical analysis, little or no sample enrichment is often sufficient, while bioanalysis often requires larger sample volumes at a certain enrichment factor for conducting comprehensive bioassays on different endpoints or further effect-directed analysis (EDA). To avoid logistic and technical issues related to the storage and transport of large volumes of water, sampling would benefit greatly from onsite extraction. This study presents a novel onsite large volume solid phase extraction (LVSPE) device tailored to fulfill the requirements for the successful effect-based and chemical screening of water resources and complies with available international standards for automated sampling devices. Laboratory recovery experiments using 251 organic compounds in the log D range from -3.6 to 9.4 (at pH7.0) spiked into pristine water resulted in acceptable recoveries and from 60 to 123% for 159 out of 251 substances. Within a European-wide demonstration program, the LVSPE was able to enrich compounds in concentration ranges over three orders of magnitude (1ngL^-1 to 2400ngL^-1). It was possible to discriminate responsive samples from samples with no or only low effects in a set of six different bioassays (i.e. acetylcholinesterase and algal growth inhibition, androgenicity, estrogenicity, fish embryo toxicity, glucocorticoid activity). The LVSPE thus proved applicable for onsite extraction of sufficient amounts of water to investigate water quality thoroughly by means of chemical analysis and effect-based tools without the common limitations due to small sample volumes.

Comparisons of discrete and integrative sampling accuracy in estimating pulsed aquatic exposures

Most current-use pesticides have short half-lives in the water column and thus the most relevant exposure scenarios for many aquatic organisms are pulsed exposures. Quantifying exposure using discrete water samples may not be accurate as few studies are able to sample frequently enough to accurately determine time-weighted average (TWA) concentrations of short aquatic exposures. Integrative sampling methods that continuously sample freely dissolved contaminants over time intervals (such as integrative passive samplers) have been demonstrated to be a promising measurement technique. We conducted several modeling scenarios to test the assumption that integrative methods may require many less samples for accurate estimation of peak 96-h TWA concentrations. We compared the accuracies of discrete point samples and integrative samples while varying sampling frequencies and a range of contaminant water half-lives (t₅₀ = 0.5, 2, and 8 d). Differences the predictive accuracy of discrete point samples and integrative samples were greatest at low sampling frequencies. For example, when the half-life was 0.5 d, discrete point samples required 7 sampling events to ensure median values > 50% and no sampling events reporting highly inaccurate results (defined as < 10% of the true 96-h TWA). Across all water half-lives investigated, integrative sampling only required two samples to prevent highly inaccurate results and measurements resulting in median values > 50% of the true concentration. Regardless, the need for integrative sampling diminished as water half-life increased. For an 8-d water half-life, two discrete samples produced accurate estimates and median values greater than those obtained for two integrative samples. Overall, integrative methods are the more accurate method for monitoring contaminants with short water half-lives due to reduced frequency of extreme values, especially with uncertainties around the timing of pulsed events. However, the acceptability of discrete sampling methods for providing accurate concentration measurements increases with increasing aquatic half-lives.

Critical assessment of the ubiquitous occurrence and fate of the insect repellent N,N-diethyl-m-toluamide in water

The insect repellent diethyltoluamide (DEET) is among the most frequently detected organic chemical contaminants in water across a wide range of geographies from around the world. These observations are raising critical questions and increasing concerns regarding potential environmental relevance, particularly when the emergence of severe neurological conditions attributed to the Zika virus has increased the use of insect repellents. After dermal application, DEET is washed from the skin when bathing and enters the municipal sewer system before discharge into the environment. Mainly measured by gas chromatography or liquid chromatography coupled to mass spectrometry (GC-MS or LC-MS), more than 200 peer-reviewed publications have already reported concentrations of DEET ranging ng/L to mg/L in several water matrices from North America, Europe, Asia, Oceania, and more recently Africa and South America. While conventional wastewater treatment technology has limited capacity of removal, advanced technologies are capable of better attenuation and could lower the environmental discharge of organic contaminants, including DEET. For instance, adsorption on activated carbon, desalinating membrane processes (nanofiltration and reverse osmosis), ozonation, and advanced oxidation processes can achieve 50% to essentially 100% DEET attenuation. Despite the abundant literature on the topic, the ubiquity of DEET in the environment still raises questions due to the apparent lack of obvious spatio-temporal trends in concentrations measured in surface water, which does not fit the expected usage pattern of insect repellents. Moreover, two recent studies showed discrepancies between the concentrations obtained by GC-MS and LC-MS analyses. While the occurrence of DEET in the environment is well established, the concentrations reported should be interpreted cautiously, considering the disparities in methodologies applied and occurrence patterns observed. Therefore, this manuscript provides a critical overview of the origin of DEET in the environment, the relevant analytical methods, the occurrence reported in peer-reviewed literature, and the attenuation efficacy of water treatment processes.

Temporal variability of micro-organic contaminants in lowland chalk catchments: New insights into contaminant sources and hydrological processes

This paper explores the temporal variation of a broad suite of micro organic (MO) compounds within hydrologically linked compartments of a lowland Chalk catchment, the most important drinking water aquifer in the UK. It presents an assessment of results from relatively high frequency monitoring at a well-characterised site, including the type and concentrations of compounds detected and how they change under different hydrological conditions including exceptionally high groundwater levels and river flow conditions during 2014 and subsequent recovery. This study shows for the first time that within the Chalk groundwater there can be a greater diversity of the MOs compared to surface waters. Within the Chalk 26 different compounds were detected over the duration of the study compared to 17 in the surface water. Plasticisers (0.06-39μg/L) were found to dominate in the Chalk groundwater on 5 visits (38.4%) accounting for 14.5% of detections but contributing highest concentrations whilst other compounds dominated in the surface water. Trichloroethene and atrazine were among the most frequently detected compounds. The limit for the total pesticide concentration detected did not exceed EU/UK prescribed concentration values for drinking water. Emerging organic compounds such as caffeine, which currently do not have water quality limits, were also detected. The low numbers of compounds found within the hyporheic zone highlight the role of this transient interface in the attenuation and breakdown of the MOs, and provision of an important ecosystem service.

Apparatus and method for time-integrated, active sampling of contaminants in fluids demonstrated by monitoring of hexavalent chromium in groundwater

Annual U.S. expenditures of $2B for site characterization invite the development of new technologies to improve data quality while reducing costs and minimizing uncertainty in groundwater monitoring. This work presents a new instrument for time-integrated sampling of environmental fluids using in situ solid-phase extraction (SPE). The In Situ Sampler (IS2) is an automated submersible device capable of extracting dissolved contaminants from water (100s-1000smL) over extended periods (hours to weeks), retaining the analytes, and rejecting the processed fluid. A field demonstration of the IS2 revealed 28-day average concentration of hexavalent chromium in a shallow aquifer affected by tidal stresses via sampling of groundwater as both liquid and sorbed composite samples, each obtained in triplicate. In situ SPE exhibited 75±6% recovery and an 8-fold improvement in reporting limit. Relative to use of conventional methods (100%), beneficial characteristics of the device and method included minimal hazardous material generation (2%), transportation cost (10%), and associated carbon footprint (2%). The IS2 is compatible with commercial SPE resins and standard extraction methods, and has been certified for more general use (i.e., inorganics and organics) by the Environmental Security Technology Certification Program (ESTCP) of the U.S. Department of Defense.

Fate of Pharmaceuticals and Their Transformation Products in Four Small European Rivers Receiving Treated Wastewater

A considerable knowledge gap exists with respect to the fate and environmental relevance of transformation products (TPs) of polar organic micropollutants in surface water. To narrow this gap we investigated the fate of 20 parent compounds (PCs) and 11 characteristic TPs in four wastewater-impacted rivers. Samples were obtained from time-integrated active sampling as well as passive sampling using polar organic chemical integrative samplers (POCIS). Seventeen out of the 20 PCs were detected in at least one of the rivers. All the PCs except acesulfame, carbamazepine, and fluconazole were attenuated along the studied river stretches, with the largest decrease found in the smallest river which had an intense surface water-pore water exchange. Seven TPs were detected, all of which were already present directly downstream of the WWTP outfall, suggesting that the WWTPs were a major source of TPs to the recipients. For anionic compounds, attenuation was the highest in the two rivers with the lowest discharge, while the pattern was not as clear for neutral or cationic compounds. For most compounds the results obtained from active sampling were not significantly different from those using POCIS, demonstrating that the cost and labor efficient POCIS is suitable to determine the attenuation of organic micropollutants in rivers.

Critical review of factors governing data quality of integrative samplers employed in environmental water monitoring

Integrative sampling enables the collection of analyte mass from environmental liquids over extended timeframes from hours to months. While the incentives to complement or replace conventional, time-discrete sampling have been widely discussed, the data quality implications of employing alternative, integrative methods have not yet been systematically studied. A critical analysis of contemporary literature reports showed the data quality of integrative samplers, whether active-advection or passive-diffusion, to be governed by uncertainty in both sampling rate and analyte recovery. Derivation of two lumped parameters, representing the coefficient of accumulation (α) of a contaminant from an environmental fluid and the coefficient of subsequent recovery (ρ) of its mass from the sampler, produced a conceptual framework for quantifying error sources in concentration data derived from accumulative samplers. Whereas the precision associated with recovery was found to be fairly consistent across eight passive-diffusion and active-advection devices (averaging 5-16% relative standard deviation, RSD), active-advection samplers effectively improve precision in sampling rate (analyte uptake), as determined for two active-advection devices (2-7% average RSD) and five passive devices (12-42% average RSD). In summary, an approach is presented whereby the data quality implications of integrative sampler design can be compared, which can inform the selection, optimization, and development of sampling systems to complement the state of the art.

Active and passive sampling for the assessment of hydrophilic organic contaminants in a river basin-ecotoxicological risk assessment

This study presents a complementary approach for the evaluation of water quality in a river basin by employing active and passive sampling. Thirty-eight hydrophilic organic compounds (HpOCs) (organohalogen herbicides, organophosphorous pesticides, carbamate, triazine, urea, pharmaceuticals, phenols, and industrial chemicals) were studied in grab water samples and in passive samplers POCIS collected along Strymonas River, Northern Greece, at three sampling campaigns during the year 2013. Almost all the target compounds were detected at the periods of high rainfall intensity and/or low flow rate. The most frequently detected compounds were aminocarb, carbaryl, chlorfenviphos, chloropropham, 2,4-D, diflubenzuron, diuron, isoproturon, metolachlor, and salicylic acid. Bisphenol A and nonylphenol were also occasionally detected. The use of POCIS allowed the detection of more micropollutants than active sampling. Low discrepancy between the concentrations obtained from both samplings was observed, at least for compounds with >50 % detection frequency; thus, POCIS could be a valuable tool for the selection and monitoring of the most relevant HpOCs in the river basin. Results showed relatively low risk from the presence of HpOCs; however, the potential risk associated with micropollutants such as carbaryl, dinoseb, diuron, fenthion, isoproturon, metolachlor, nonylphenol, and salicylic acid should not be neglected.

Active Sampling Device for Determining Pollutants in Surface and Pore Water - the In Situ Sampler for Biphasic Water Monitoring

We designed and evaluated an active sampling device, using as analytical targets a family of pesticides purported to contribute to honeybee colony collapse disorder. Simultaneous sampling of bulk water and pore water was accomplished using a low-flow, multi-channel pump to deliver water to an array of solid-phase extraction cartridges. Analytes were separated using either liquid or gas chromatography, and analysis was performed using tandem mass spectrometry (MS/MS). Achieved recoveries of fipronil and degradates in water spiked to nominal concentrations of 0.1, 1, and 10 ng/L ranged from 77 ± 12 to 110 ± 18%. Method detection limits (MDLs) were as low as 0.040–0.8 ng/L. Extraction and quantitation of total fiproles at a wastewater-receiving wetland yielded concentrations in surface water and pore water ranging from 9.9 ± 4.6 to 18.1 ± 4.6 ng/L and 9.1 ± 3.0 to 12.6 ± 2.1 ng/L, respectively. Detected concentrations were statistically indistinguishable from those determined by conventional, more laborious techniques (p > 0.2 for the three most abundant fiproles). Aside from offering time-averaged sampling capabilities for two phases simultaneously with picogram-per-liter MDLs, the novel methodology eliminates the need for water and sediment transport via in situ solid phase extraction.