Removal of a wide range of emerging pollutants from wastewater treatment plant discharges by micro-grain activated carbon in fluidized bed as tertiary treatment at large pilot scale

The behavior of pharmaceutically active compounds and contrast agents during wastewater treatment - Combining sampling strategies and analytical techniques: A critical review

Increasing consumption of pharmaceuticals and the respective consequences for the aquatic environment have been the focus of many studies over the last thirty years. Various aspects in this field were investigated, considering diverse pharmaceutical groups and employing a wide range of research methodologies. Various questions from the perspectives of different research areas were devised and answered, resulting in a large mix of individual findings and conclusions. Collectively, the results of the studies offer a comprehensive overview. The large variety of methods and strategies, however, demands close attention when comparing and combining information from heterogeneous projects. This review critically examines the application of diverse sampling techniques as well as analytical methods in investigations concerning the behavior of pharmaceutically active compounds (PhACs) and contrast agents (CAs) in wastewater treatment plants (WWTPs). The combination of sampling and analysis is discussed with regard to its suitability for specific scientific problems. Different research focuses need different methods and answer different questions. An overview of studies dealing with the fate and degradation of PhACs and CAs in WWTPs is presented, discussing their strategic approaches and findings. This review includes surveys of anticancer drugs, antibiotics, analgesics and anti-inflammatory drugs, antidiabetics, beta blockers, hormonal contraceptives, lipid lowering agents, antidepressants as well as contrast agents for X-ray and magnetic resonance imaging.

Mastering granular activated carbon filtration to remove organic micropollutants, antibiotic resistance and metals for municipal wastewater reuse

GAC filtration of municipal wastewater was optimized and intensified, making its implementation and operation directly after secondary clarification possible and relevant. GAC was first selected based on laboratory tests. Performances on organic micropollutants were linked to the repartition of BET surface between micropores and meso/macropores. At pilot scale, in order to limit the impact of head loss, downflow declogging sequences (DCS) were implemented and upflow filtration tested. 6 to 12 DCS per day led to a 4.7-5.5-fold increase of particles retention capacity between backwashes (cycle duration of 20-120 h), and upflow operations improved head loss evolution profile with only a slight GAC (<15 %) expansion. DCS allows backwash frequency reduction, enabling significant water savings. Both adaptations maintained high organic micropollutants removals compared to a review of 16 GAC studies at pilot or full-scale, results being in the upper range. A specific dose of 2.0-2.5 g GAC/gC was necessary to obtain an average removal of pharmaceuticals and benzotriazole of 80 % at 20 min contact time, which is comparable to PAC and low granulometry GAC. Higher doses are needed for PFAS but >80 % removals are achievable. Particles, TKN, particulate phosphorus and organic matter are well removed by GAC filtration in both configurations. Biological activity is observed through nitrogen transformation in the GAC bed. Heavy metals are greatly removed in GAC filtration, in particular Cd, Cu, Ni and Pb, probably through biosorption onto the biofilm, developed within the GAC bed. For wastewater reuse applications, GAC filtration has an added value through physicochemical quality improvement and fecal contamination indicators removal of 1 log, facilitating the implementation and optimizing the design of a post-disinfection. Antibiotic resistant bacteria and antibiotic resistance genes are also partially retained in GAC filtration. Finally, biological wastewater treatments combined to GAC filtration is a good solution to effectively treat organic micropollutants together with heavy metals and preparing post-disinfection for reuse.

Enhanced EDC removal from water through electron beam-mediated adsorber particle integration in microfiltration membranes

The existence of endocrine disrupting chemicals (EDCs) in water and wastewater gives rise to significant environmental concerns. Conventional treatment approaches demonstrate limited capacity for EDC removal. Thus, incorporation of advanced separation procedures becomes essential to enhance the efficiency of EDC removal. In this work, adsorber composite microfiltration polyethersulfone membranes embedded with divinyl benzene polymer particles were created. These membranes were designed for effectively removing a variety of EDCs from water. The adsorber particles were synthesized using precipitation polymerization. Subsequently, they were integrated into the membrane scaffold through a phase inversion process. The technique of electron beam irradiation was applied for the covalent immobilization of particles within the membrane scaffold. Standard characterization procedures were carried out (i.e., water permeance, contact angle, X-ray photoelectron spectroscopy and scanning electron microscopy) to gain a deep understanding of the synthesized membrane properties. Dynamic adsorption experiments demonstrated the excellent capability of the synthesized composite membranes to effectively remove EDCs from water. Particularly, among the various target molecules examined, testosterone stands out with the most remarkable enhancement, presenting an adsorption loading of 220 mg m-2. This is an impressive 26-fold increase in the adsorption when compared to the performance of the pristine membrane. Similarly, androst-4-ene-3,17-dione exhibited an 18-fold improvement in adsorption capacity in comparison to the pristine membrane. The composite membranes also exhibited significant adsorption capacities for other key compounds, including 17β-estradiol, equilin, and bisphenol-A. With the implementation of an effective regeneration procedure, the composite membranes were put to use for adsorption over three consecutive cycles without any decline in their adsorption capacity.

Veterinary pharmaceutical as emerging contaminants in wastewater and surface water: An overview

Veterinary pharmaceuticals have become of interest due to their indiscriminate use. Thus, this paper compiles studies on detection in surface and wastewater, and the treatment applied for their removal. Additionally, a case study was performed to evaluate its commercialization, as the ecological risk assessment for the most relevant compounds. 241 compounds were detected. The highest concentrations were found for antibiotics such as oxytetracycline, amoxicillin, and monensin, with values up to 3732.4 µg/L. Biological treatments have been mainly reported, obtaining removal greater than 80% for sulfadiazine, sulfamethazine, sulfamethoxazole, enrofloxacin, and oxytetracycline. Considering the case study, enrofloxacin and oxytetracycline were widely commercialized. Finally, there was a low risk for the species exposed to enrofloxacin, in contrast, the species exposed to oxytetracycline presented a high risk of long-term mortality. Concluding that veterinary compounds have emerged as a significant concern regarding water source contamination, owing to their potential adverse effects on aquatic biota and even human. This is particularly relevant because many water bodies that receive wastewater are utilized for drinking water purposes. Consequently, the development of comprehensive, full-scale systems for efficient antibiotic removal before their introduction into water sources becomes imperative. Equally important is the need to reconsider their extensive use altogether.

Highly graphitic Fe-doped carbon xerogels as dual-functional electro-Fenton catalysts for the degradation of tetracycline in wastewater

Fe-doped carbon xerogels with a highly developed graphitic structure were synthesized by a one-step sol-gel polymerization. These highly graphitic Fe-doped carbons are presented as promising dual-functional electro-Fenton catalysts to perform both the electro-reduction of O₂ to H₂O₂ and H₂O₂ catalytic decomposition (Fenton) for wastewater decontamination. The amount of Fe is key to the development of this electrode material, since affects the textural properties; catalyzes the development of graphitic clusters improving the electrode conductivity; and influences the O₂-catalyst interaction controlling the H₂O₂ selectivity but, at the same time is the catalyst for the decomposition of the electrogenerated H₂O₂ to OH^• radicals for the organic pollutants oxidation. All materials achieve the development of ORR via the 2-electron route. The presence of Fe considerably improves the electro-catalytic activity. However, a mechanism change seems to occur at around -0.5 V in highly Fe-doped samples. At potential lower than -0.5 eV, the present of Fe^δ+ species or even Fe-O-C active sites favour the selectivity to 2e-pathway, however at higher potentials, Fe^δ+ species are reduced favoring a O-O strong interaction enhancing the 4e-pathway. The Electro-Fenton degradation of tetracycline was analyzed. The TTC degradation is almost complete (95.13%) after 7 h of reaction without using any external Fenton-catalysts.

Investigation of the performance of activated carbon cloth to remove glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos from aqueous solutions by adsorption/electrosorption

The present study investigates the removal of glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos herbicides from their 5 × 10^-5 M aqueous solutions onto activated carbon cloth by adsorption and electrosorption. Analysis of these highly polar herbicides was achieved by UV-visible absorbance measurements, after derivatization with 9-fluorenylmethyloxycarbonyl chloride. The limit of quantification values of glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos were 1.06 × 10^-6 mol L^-1, 1.38 × 10^-6 mol L^-1, 1.32 × 10^-6 mol L^-1 and 1.08 × 10^-6 mol L^-1, respectively. Glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos were removed from their aqueous solutions with higher efficiencies by means of electrosorption (78.2%, 94.9%, 82.3% and 97%, respectively) than of open-circuit adsorption (42.5%, 22%, 6.9% and 81.8%, respectively). Experimental kinetic data were fitted to pseudo-first order and pseudo-second order kinetic models. It was determined that pseudo-second order kinetic model represents experimental data better with satisfactory coefficient of determination, r² (> 0.985) and normalized percent deviation, P (< 5.15) values. Adsorption isotherm data were treated according to Freundlich and Langmuir isotherm models. Based on the r² (> 0.98) and P (< 5.9) values, it was found that experimental data well fitted to Freundlich isotherm model. Adsorption capacities of activated carbon cloth for glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos, expressed in terms of Freundlich constant, were calculated as 20.31, 118.73, 239.33 and 30.68 mmol g^-1, respectively. The results show that the studied ACC can be used in home/business water treatment systems as an adsorbent due to its high adsorption capacity.

Activated carbon enhanced traditional activated sludge process for chemical explosion accident wastewater treatment

With the development of industries, explosion accidents occur frequently during production, transportation, usage and storage of hazard chemicals. It remained challenging to efficiently treat the resultant wastewater. As an enhancement of traditional process, the activated carbon-activated sludge (AC-AS) process has a promising potential in treating wastewater with high concentrations of toxic compounds, chemical oxygen demand (COD) and ammonia nitrogen (NH₄⁺-N), etc. In this paper, activated carbon (AC), activated sludge (AS) and AC-AS were used to treat the wastewater produced from an explosion accident in the Xiangshui Chemical Industrial Park. The removal efficiency was assessed by the removal performances of COD, dissolved organic carbon (DOC), NH₄⁺-N, aniline and nitrobenzene. Increased removal efficiency and shortened treatment time were achieved in the AC-AS system. To achieve the same COD, DOC and aniline removal (90%), the AC-AS system saved 30, 38 and 58 h compared with the AS system, respectively. The enhancement mechanism of AC on the AS was explored by metagenomic analysis and three-dimensional excitation-emission-matrix spectra (3DEEMs). More organics, especially aromatic substances were removed in the AC-AS system. These results showed that the addition of AC promoted the microbial activity in pollutant degradation. Bacteria, such as Pyrinomonas, Acidobacteria and Nitrospira and genes, such as hao, pmoA-amoA, pmoB-amoB and pmoC-amoC, were found in the AC-AS reactor, which might have played important roles in the degradation of pollutants. To sum up, AC might have enhanced the growth of aerobic bacteria which further improved the removal efficiency via the combined effects of adsorption and biodegradation. The successful treatment of Xiangshui accident wastewater using the AC-AS demonstrated the potential universal characteristics of the process for the treatment of wastewater with high concentration of organic matter and toxicity. This study is expected to provide reference and guidance for the treatment of similar accident wastewaters.

MCDA-DEA approach to construct a composite indicator for effluents from WWTPs considering the influence of PPCPs

Considering current water situation, reuse is an effective solution to meet water demand and reduce pressure on conventional water sources. However, pharmaceutical and personal care products (PPCPs) in effluents from wastewater treatment plants (WWTPs) decrease their quality and suitability. With the aim of identifying and monitoring both the influence of PPCPs and the suitability of effluents to be reused, this study proposes the development of a composite indicator (CI) related to PPCP presence in WWTPs, through the common weight multi-criteria decision analysis (MCDA)-data envelopment analysis (DEA) model. Obtaining a CI for PPCPs is a novel approach in the published literature, showing a new perspective in PPCP management and their influence in wastewater treatment. Furthermore, this study proposes an improvement on MCDA-DEA model which maintains the initial hierarchy obtained for the units analyzed. The development of CI is based on information about the technological, environmental, social, and biological issues of WWTPs. Results show that 4 of the 33 WWTPs analysed had the best CI values, meaning that their effluents have lower environmental impact. The development of a CI related to PPCPs in WWTPs suggests that further steps are needed to manage the WWTP effluents. Hence, the need to implement preventive measures in WWTPs has been shown, even though the removal of PPCPs is not yet part of European law. This work highlights the importance of considering PPCPs as priority pollutants in wastewater management and reuse frameworks, to guarantee low environmental impact and adapt wastewater reuse based on a circular economy approach. HIGHLIGHTS: Emerging contaminants (PPCPs) are used as effluent quality indicators. A composite indicator for PPCPs performance has been developed through MCDA-DEA model. Indicator obtained allow decision makers implementing concrete actions to assess effluent quality. Results show the improvement capacity of the effluents quality through PPCPs removing.

From Fenton and ORR 2e−-Type Catalysts to Bifunctional Electrodes for Environmental Remediation Using the Electro-Fenton Process

Currently, the presence of emerging contaminants in water sources has raised concerns worldwide due to low rates of mineralization, and in some cases, zero levels of degradation through conventional treatment methods. For these reasons, researchers in the field are focused on the use of advanced oxidation processes (AOPs) as a powerful tool for the degradation of persistent pollutants. These AOPs are based mainly on the in-situ production of hydroxyl radicals (OH•) generated from an oxidizing agent (H2O2 or O2) in the presence of a catalyst. Among the most studied AOPs, the Fenton reaction stands out due to its operational simplicity and good levels of degradation for a wide range of emerging contaminants. However, it has some limitations such as the storage and handling of H2O2. Therefore, the use of the electro-Fenton (EF) process has been proposed in which H2O2 is generated in situ by the action of the oxygen reduction reaction (ORR). However, it is important to mention that the ORR is given by two routes, by two or four electrons, which results in the products of H2O2 and H2O, respectively. For this reason, current efforts seek to increase the selectivity of ORR catalysts toward the 2e− route and thus improve the performance of the EF process. This work reviews catalysts for the Fenton reaction, ORR 2e− catalysts, and presents a short review of some proposed catalysts with bifunctional activity for ORR 2e− and Fenton processes. Finally, the most important factors for electro-Fenton dual catalysts to obtain high catalytic activity in both Fenton and ORR 2e− processes are summarized.

Erythromycin Scavenging from Aqueous Solutions by Zeolitic Materials Derived from Fly Ash

Erythromycin (EA) is an antibiotic whose concentration in water and wastewater has been reported to be above the standard levels. Since the methods used so far to remove EA from aquatic environments have not been effective, the development of effective methods for EA removal is necessary. In the present study, fly ash (FA)-based zeolite materials, which have not been investigated as EA sorbents before, were used. The possibilities of managing waste FA and using its transformation products for EA sorption were presented. The efficiency of EA removal from experimental solutions and real wastewater was evaluated. In addition, the sorbents' mineral composition, chemical composition, and physicochemical properties and the effects of adsorbent mass, contact time, initial EA concentration, and pH on EA removal were analyzed. The EA was removed within the first 2 min of the reaction with an efficiency of 99% from experimental solutions and 94% from real wastewater. The maximum adsorption capacities were 314.7 mg g^-1 for the fly ash-based synthetic zeolite (NaP1_FA) and 363.0 mg g^-1 for the carbon-zeolite composite (NaP1_C). A fivefold regeneration of the NaP1_FA and NaP1_C showed no significant loss of adsorption efficiency. These findings indicate that zeolitic materials effectively remove EA and can be further investigated for removing other pharmaceuticals from water and wastewater.

New insights into the occurrence and removal of 36 pesticides in pesticide wastewater treatment plants in Korea

This study investigates the occurrence of 36 pesticides-including 33 that were monitored from 2007 to 2019 in Korean rivers-in wastewaters from pesticide manufacturing facilities (PMFs) and in 13 pesticide wastewater treatment plants (PWWTPs). Furthermore, an approach for the effective removal of these pesticides from pesticide wastewater (PW) is proposed. Among the 36 pesticides investigated, 32 were found to be present in the PMF wastewater and PWWTP influents (at concentrations ≤466.8 mg/L). In addition, 24 of the 36 pesticides were detected in PWWTP effluents, indicating that effluents are discharged without the complete removal of many pesticides. Moreover, the PWWTP effluent influences the presence of pesticides in river (confidence interval: ≥ 95%; p < 0.05). Although the chemical oxidation-activated sludge process is frequently recommended for the treatment of PWs, the findings from the current study indicate that an activated sludge-activated carbon adsorption process is more suitable for PW treatment due to its superior removal efficiency, treatment stability, and economic feasibility. Consequently, its application for the treatment of PWs can markedly decrease the levels of pesticides discharged into rivers.

Efficient adsorptive removal of fluoroquinolone antibiotics from water by alkali and bimetallic salts co-hydrothermally modified sludge biochar

Fluoroquinolones are one of most commonly used antibiotics for preventing and treating bacterial infections and their unsatisfactory removal by conventional wastewater treatment technology have aroused widespread attention. A novel adsorbent of KMSBC was the first time synthesized and tested to adsorb three typical fluoroquinolone antibiotics of CIP, NOR and OFL from water. The characterization analysis showed that KMSBC possessed the superior porous structure, abundant functional groups and greater graphitic degree. Together with kinetics, isotherms, thermodynamics and critical factors (e.g., biochar dose, reaction time/temperature, fluoroquinolone antibiotics concentration, pH, co-existing ionic strength and HA concentration) analysis suggested that pore filling, π-π conjugation, H-bonding and electrostatic interaction were the key mechanisms for fluoroquinolone antibiotics adsorption by KMSBC. KMSBC exhibited the optimum adsorption performance at pH = 5 despite the adsorbates. The maximum adsorption capacity of KMSBC for CIP, NOR and OFL were 49.9, 55.7 and 47.4 mg/g at 25 °C, respectively. Also, KMSBC exhibited the good magnetic sensitivity and stability with the leaching concentrations of Fe were far below than environmental limit (GB5749-2006) at various pH (from 3 to 12), ionic strength and HA concentrations. Additionally, KMSBC performed a stable sustainable adsorption performance in recycles by NaOH regeneration. Thus, KMSBC had the potential to be a promising adsorbent for fluoroquinolone antibiotics removal with favorable adsorption capacity, environmental security and easy regeneration performance.

Pharmaceutical compounds used in the COVID-19 pandemic: A review of their presence in water and treatment techniques for their elimination

During the COVID-19 pandemic, high consumption of antivirals, antibiotics, antiparasitics, antiprotozoals, and glucocorticoids used in the treatment of this virus has been reported. Conventional treatment systems fail to efficiently remove these contaminants from water, becoming an emerging concern from the environmental field. Therefore, the objective of the present work is to address the current state of the literature on the presence and removal processes of these drugs from water bodies. It was found that the concentration of most of the drugs used in the treatment of COVID-19 increased during the pandemic in water bodies. Before the pandemic, Azithromycin concentrations in surface waters were reported to be in the order of 4.3 ng L^-1, and during the pandemic, they increased up to 935 ng L^-1. Laboratory scale studies conclude that adsorption and advanced oxidation processes (AOPs) can be effective in the removal of these drugs. Up to more than 80% removal of Azithromycin, Chloroquine, Ivermectin, and Dexamethasone in aqueous solutions have been reported using these processes. Pilot-scale tests achieved 100% removal of Azithromycin from hospital wastewater by adsorption with powdered activated carbon. At full scale, treatment plants supplemented with ozonation and artificial wetlands removed all Favipiravir and Azithromycin, respectively. It should be noted that hybrid technologies can improve removal rates, process kinetics, and treatment cost. Consequently, the development of new materials that can act synergistically in technically and economically sustainable treatments is required.

A state of the art overview of carbon-based composites applications for detecting and eliminating pharmaceuticals containing wastewater

The growing prevalence of new toxins in the environment continues to cause widespread concerns. Pharmaceuticals, organic pollutants, heavy metal ions, endocrine-disrupting substances, microorganisms, and others are examples of persistent organic chemicals whose effects are unknown because they have recently entered the environment and are displaying up in wastewater treatment facilities. Pharmaceutical pollutants in discharged wastewater have become a danger to animals, marine species, humans, and the environment. Although their presence in drinking water has generated significant concerns, little is known about their destiny and environmental effects. As a result, there is a rising need for selective, sensitive, quick, easy-to-handle, and low-cost early monitoring detection systems. This study aims to deliver an overview of a low-cost carbon-based composite to detect and remove pharmaceutical components from wastewater using the literature reviews and bibliometric analysis technique from 1970 to 2021 based on the web of science (WoS) database. Various pollutants in water and soil were reviewed, and different methods were introduced to detect pharmaceutical pollutants. The advantages and drawbacks of varying carbon-based materials for sensing and removing pharmaceutical wastes were also introduced. Finally, the available techniques for wastewater treatment, challenges and future perspectives on the recent progress were highlighted. The suggestions in this article will facilitate the development of novel on-site methods for removing emerging pollutants from pharmaceutical effluents and commercial enterprises.

Key Factors for Activated Carbon Adsorption of Pharmaceutical Compounds from Wastewaters: A Multivariate Modelling Approach

Projection to Latent Structures (PLS) regression, a generalization of multiple linear regression, is used to model two datasets (40 observed data points each) of adsorption removal of three pharmaceutical compounds (PhCs), of different therapeutic classes and physical–chemical properties (carbamazepine, diclofenac, and sulfamethoxazole), from six real secondary effluents collected from wastewater treatment plants onto different powdered activated carbons (PACs). For the PLS regression, 25 descriptors were considered: 7 descriptors related to the PhCs properties, 10 descriptors related to the wastewaters properties (8 related to the organic matrix and 2 to the inorganic matrix), and 8 descriptors related to the PACs properties. This modelling approach showed good descriptive capability, showing that hydrophobic PhC-PAC interactions play the major role in the adsorption process, with the solvation energy and log Kow being the most suitable descriptors. The results also stress the importance of the competition effects of water dissolved organic matter (DOM), namely of its slightly hydrophobic compounds impacting the adsorption capacity or its charged hydrophilic compounds impacting the short-term adsorption, while the water inorganic matrix only appears to impact PAC adsorption capacity and not the short-term adsorption. For the pool of PACs tested, the results point to the BET area as a good descriptor of the PAC capacity, while the short-term adsorption kinetics appears to be better related to its supermicropore volume and density. The improvement in these PAC properties should be regarded as a way of refining their performance. The correlations obtained, involving the impact of water, PhC and PAC-related descriptors, show the existence of complex interactions that a univariate analysis is not sufficient to describe.

Removal of contaminants of emerging concern from multicomponent systems using carbon dioxide activated biochar from lignocellulosic feedstocks

Adsorption of six contaminants of emerging concern (CECs) - caffeine, chloramphenicol, carbamazepine, bisphenol A, diclofenac, and triclosan - from a multicomponent solution was studied using activated biochars obtained from three lignocellulosic feedstocks: wheat straw, softwood, and peach stones. Structural parameters related to the porosity and ash content of activated biochar and the hydrophobic properties of the CECs were found to influence the adsorption efficiency. For straw and softwood biochar, activation resulted in a more developed mesoporosity, whereas activation of peach stone biochar increased only the microporosity. The most hydrophilic CECs studied, caffeine and chloramphenicol, displayed the highest adsorption (22.8 and 11.3 mg g^-1) onto activated wheat straw biochar which had the highest ash content of the studied adsorbents (20 wt%). Adsorption of bisphenol A and triclosan, both relatively hydrophobic substances, was highest (31.6 and 30.2 mg g^-1) onto activated biochar from softwood, which displayed a well-developed mesoporosity and low ash content.

Pharmaceutical Compounds in Aquatic Environments-Occurrence, Fate and Bioremediation Prospective

Various contaminants of emerging concern (CECs) have been detected in different ecosystems, posing a threat to living organisms and the environment. Pharmaceuticals are among the many CECs that enter the environment through different pathways, with wastewater treatment plants being the main input of these pollutants. Several technologies for the removal of these pollutants have been developed through the years, but there is still a lack of sustainable technologies suitable for being applied in natural environments. In this regard, solutions based on natural biological processes are attractive for the recovery of contaminated environments. Bioremediation is one of these natural-based solutions and takes advantage of the capacity of microorganisms to degrade different organic pollutants. Degradation of pollutants by native microorganisms is already known to be an important detoxification mechanism that is involved in natural attenuation processes that occur in the environment. Thus, bioremediation technologies based on the selection of natural degrading bacteria seem to be a promising clean-up technology suitable for application in natural environments. In this review, an overview of the occurrence and fate of pharmaceuticals is carried out, in which bioremediation tools are explored for the removal of these pollutants from impacted environments.

Safety evaluation and ibuprofen removal via an Alternanthera philoxeroides-based biochar

Pharmaceutical and personal care products (PPCPs) are a representative class of emerging contaminants. This study aimed to investigate the PPCP removal performance and application safety of a biochar fabricated using the invasive plant Alternanthera philoxeroides (APBC). According to scanning electron microscopy and pore size analyses, APBC exhibited a porous structure with a specific surface area of 857.5 m²/g. A Fourier transform infrared spectroscopy analysis indicated the presence of surface functional groups, including phosphorus-containing groups, C=O, C=C, and -OH. The adsorption experiment showed that the maximum removal efficiency of ibuprofen was 97% at an initial concentration of 10 mg/L and APBC dosage of 0.8 g/L. The adsorption kinetics were fitted by the pseudo-second-order model with the highest correlation coefficient (R² = 0.9999). The adsorption isotherms were well described by the Freundlich model (R² = 0.9896), which indicates a dominant multilayer adsorption. The maximum adsorption capacity of APBC was 172 mg/g. A toxicity evaluation, based on Chlorella pyrenoidosa and human epidermal BEAS-2B cells, was carried out using a spectrum analysis, thiazolyl blue tetrazolium bromide assay, and flow cytometry. The results of the above showed the low cytotoxicity of APBC and demonstrated its low toxicity in potential environmental applications.

A review of the adsorption-biological hybrid processes for the abatement of emerging pollutants: Removal efficiencies, physicochemical analysis, and economic evaluation

The limited efficiency of conventional wastewater treatment plants (WWTPs) in emerging pollutants (EPs) removal encourages the development of alternative technologies for the adequate treatment of wastewater, due to its adverse effects on human health and ecosystems. The biological, physical or chemical hybrid technologies to treat EPs results interesting since they can enhance the performance of WWTPs. Among them, hybrid adsorption/biological technology could offer different possibilities that are explored in this work (PAC-MBR, PACT/GAC-CAS, BAC configurations). In this way, different variations in the adsorption process have been considered: the form of the adsorbent, the feed to the system, and the type of biological process, either conventional activated sludge (CAS), membrane bioreactor (MBR) or biofilm systems. For each combination, the removal efficiency of micropollutants, classified according to their use into pharmaceuticals, personal care products (PCPs) and other micropollutants (mainly benzotriazoles) was analysed. From reported data, it was observed a beneficial synergistic effect of dipole moment and octanol-water partition coefficient on the removal efficiency of micropollutants by adsorption/biological hybrid technology. Finally, a preliminary economic evaluation of the powdered activated carbon in a conventional activated sludge reactor (PACT), powdered activated carbon-membrane bioreactor (PAC-MBR) and biological activated carbon (BAC) hybrid systems was carried out by analysing the capital expenditure (CAPEX) of plants for capacities up to 75,000 m³d^-1. Likewise, estimations of adsorbent concentration for a hypothetical plant with a capacity of 10,000 m³d^-1 is presented. Among these hybrid configurations, PAC-MBR achieved the highest micropollutant elimination percentages; however, it presents the highest CAPEX and activated carbon requirements.

Evaluation of Sand Filtration and Activated Carbon Adsorption for the Post-Treatment of a Secondary Biologically-Treated Fungicide-Containing Wastewater from Fruit-Packing Industries

In this work, a sand filtration-activated carbon adsorption system was evaluated to remove the fungicide content of a biologically treated effluent. The purification process was mainly carried out in the activated carbon column, while sand filtration slightly contributed to the improvement of the pollutant parameters. The tertiary treatment system, which operated under the batch mode for 25 bed volumes, resulted in total and soluble COD removal efficiencies of 76.5 ± 1.5% and 88.2 ± 1.3%, respectively, detecting total COD concentrations below 50 mg/L in the permeate of the activated carbon column. A significant pH increase and a respective electrical conductivity (EC) decrease also occurred after activated carbon adsorption. The total and ammonium nitrogen significantly decreased, with determined concentrations of 2.44 ± 0.02 mg/L and 0.93 ± 0.19 mg/L, respectively, in the activated carbon permeate. Despite that, the initial imazalil concentration was greater than that of the fludioxonil in the biologically treated effluent (i.e., 41.26 ± 0.04 mg/L versus 7.35 ± 0.43 mg/L, respectively). The imazalil was completely removed after activated carbon adsorption, while a residual concentration of fludioxonil was detected. Activated carbon treatment significantly detoxified the biologically treated fungicide-containing effluent, increasing the germination index by 47% in the undiluted wastewater or by 68% after 1:1 v/v dilution.

Carbamazepine and Diclofenac Removal Double Treatment: Oxidation and Adsorption

In the present research, the effect of two hybrid treatments, ozone followed by powdered activated carbon (PAC) or PAC followed by ozone (O₃), was studied for the removal of two drugs present in water: diclofenac and carbamazepine. In the study, two initial concentrations of each of the contaminants, 0.7 mg L^-1 and 1.8 mg L^-1, were used. Different doses of PAC between 4-20 mg L^-1 were studied as variables, as well as different doses of O₃ between 0.056-0.280 mg L^-1. The evolution of the concentration of each contaminant over time was evaluated. From the results obtained, it was concluded that the combined treatment with ozone followed by PAC reduces between 50% and 75% the time required to achieve 90% removal of diclofenac when compared with the time required when only activated carbon was used. In the case of carbamazepine, the time required was 97% less. For carbamazepine, to achieve reduction percentages of up to 90%, O₃ treatment followed by PAC acted faster than PAC followed by O₃. In the case of diclofenac, PAC treatment followed by O₃ was faster to reach concentrations of up to 90%. However, to reach yields below 80%, O₃ treatment followed by PAC was more efficient.

Spatial variation of pharmaceuticals in the unit processes of full-scale municipal wastewater treatment plants in Korea

Several reports have elucidated the removal of pharmaceutical residues in municipal wastewater treatment plants (WWTPs). However, there remains a need to determine the spatial distribution of pharmaceuticals in the unit processes of full-scale municipal WWTPs. Herein, spatial variations of fifteen pharmaceuticals in the unit processes of four full-scale municipal WWTPs were assessed by analyzing both solid and liquid samples. Furthermore, different pathways of each pharmaceutical such as biodegradation, adsorption, deconjugation, and electrostatic interaction were investigated. Pharmaceutical mass loading were measured at various points for the different unit process and evaluated using liquid chromatography-tandem mass spectrometry. The average mass loading of acetaminophen and caffeine decreased tremendously in the first biological treatment process regardless of the process configuration. In contrast, a temporary increase was observed in the mass loading of ibuprofen in the anaerobic and/or anoxic processes, which was presumably caused by deconjugation. Additionally, the adverse effect of coagulation on ibuprofen removal was validated. The major removal mechanism for the selected antibiotics, except for sulfamethoxazole, was the adsorption by biosolids due to electrostatic interaction. Subsequently, a drastic decrease was observed in their mass loadings in the solid-liquid separation process of the WWTPs. The membrane bioreactor (MBR) shows excellent capability for mitigation of pharmaceuticals in municipal wastewater because it comprises a high concentration of biosolids that act as adsorbents. The evaluation of the spatial variations of the selected pharmaceuticals in different unit processes provides valuable information on their behavior and removal mechanisms.

Efficacy of atrazine pesticide reduction in aqueous solution using activated carbon, ozone and a combination of both

In this study, the reduction of the emerging organic contaminant atrazine in water, was investigated by adsorption, oxidation and a combination of both technologies. Adsorption tests were performed using method ASTM D3860-98 with two types of activated carbon: powdered activated carbon and granular activated carbon. For the oxidation tests, advanced ozone oxidation technology was used. Finally, in the combined tests, firstly adsorption treatment was applied followed by oxidation and then the order was reversed. We studied the contaminant removal percentage using different treatments at various reaction times. Results for the different treatments under study showed that, for an initial atrazine concentration of 0.7 mg L^-1 and a dose of 16 mg L^-1 of powdered activated carbon, with contact times of 60 min, 24 h and 48 h, percentage reductions of the contaminant of 81%, 92% and 94% respectively were obtained. For the same concentration of contaminant, but instead using granular activated carbon, the percentage reduction of atrazine at 60 min was 2%, this percentage rising to 34% and 35% after 24 and 48 h of contact time, respectively. For the same initial contaminant concentration, when ozone was applied at a dose of 19.7 mg L^-1, and with a reaction time of 18 min, a reduction of atrazine of 93% was obtained, but oxidation by-products were also produced. For the combined treatments, with the same initial concentration of contaminant and the same doses of carbon and ozone as previously indicated, better contaminant reductions were obtained when the treatment started with activated carbon followed by ozone, achieving a 90% reduction of atrazine observing a 17 minute contact time with powdered activated carbon and a 3 day contact time using the granulated carbon. When the order was reversed by starting with ozone, the contact time was 52 min and 4 days, respectively.

Fluorescence excitation/emission matrices as a tool to monitor the removal of organic micropollutants from wastewater effluents by adsorption onto activated carbon

Monitoring the removal of organic micropollutants (OMPs) in advanced wastewater treatment facilities requires expensive and time-consuming analytical methods that cannot be installed online. Spectroscopic techniques such as fluorescence excitation/emission spectroscopy were demonstrated to offer the potential for monitoring OMPs removal in conventional wastewater treatment plants or ozonation pilots but their application to activated carbon (AC) adsorption processes was only investigated at lab scale and not in real treatment facilities. In this study, indexes from fluorescence emission/excitation matrices (EEMs) were used to find correlations with the removal of 28 OMPs from a large-scale AC pilot in fluidized bed employed for wastewater advanced treatment, as well as from batch experiments. Differences in OMPs removal could be observed depending on the operational conditions (i.e. pilot or batch experiments, contact time, type of AC) and the physico-chemical properties of the molecules. 7 PARAFAC components were derived from the fluorescence EEMs of 60 samples obtained before and after adsorption. Positive correlations were obtained between the removal of fluorescence indexes and most OMPs, and correlation coefficients were much higher than the ones obtained with UV₂₅₄, confirming the interesting potential of fluorescence spectroscopy to accurately monitor adsorption performances at the industrial scale. The highest correlation coefficients were obtained for OMPs having the best removals while the ones that were refractory to adsorption, as well as to interactions with DOM, exhibited weak correlations. These results suggest that interactions between OMPs and fluorescing DOM and their subsequent co-adsorption onto AC were at the origin of the correlations found. Lower correlations were also found for the most biodegradable OMPs, which indicated that the occurrence of biological effects could make the monitoring of these compounds more challenging.

Study of the Potential of Water Treatment Sludges in the Removal of Emerging Pollutants

Presently, water quantity and quality problems persist both in developed and developing countries, and concerns have been raised about the presence of emerging pollutants (EPs) in water. The circular economy provides ways of achieving sustainable resource management that can be implemented in the water sector, such as the reuse of drinking water treatment sludges (WTSs). This study evaluated the potential of WTS containing a high concentration of activated carbon for the removal of two EPs: the steroid hormones 17β-estradiol (E2) and 17α-ethinylestradiol (EE2). To this end, WTSs from two Portuguese water treatment plants (WTPs) were characterised and tested for their hormone adsorbance potential. Both WTSs showed a promising adsorption potential for the two hormones studied due to their textural and chemical properties. For WTS1, the final concentration for both hormones was lower than the limit of quantification (LOQ). As for WTS2, the results for E2 removal were similar to WTS1, although for EE2, the removal efficiency was lower (around 50%). The overall results indicate that this method may lead to new ways of using this erstwhile residue as a possible adsorbent material for the removal of several EPs present in wastewaters or other matrixes, and as such contributing to the achievement of Sustainable Development Goals (SDG) targets.

Contaminants of Emerging Concern in African Wastewater Effluents: Occurrence, Impact and Removal Technologies

Worldwide, the pollution of water bodies by contaminants of emerging concern (CECs) such as pharmaceuticals, endocrine disrupting compounds, flame retardants including brominated flame retardants (BFRs) and perfluorochemicals (PFCs), micro plastics, nanomaterials, and algal toxins, to name just a few, is creating a new set of challenges to the conventional wastewater treatment facilities, which demonstrate inefficiency in removing/degrading many CECs. As a consequence, environmentalists started to detect the presence of some of those contaminants at alarming levels in certain countries, with possible negative effects on aquatic species and often increased potential for human health risks through the exposure to the contaminated waters, or the reuse of treated wastewater in agriculture and household use. Such issues are more accentuated in the African continent due to various socio-economic problems giving rise to poor sanitation systems and serious shortages in wastewater treatment plants in many regions, making it difficult to tackle the problem of conventional pollutants, let alone to deal with the more challenging CECs. Thus, in order to effectively deal with this emerging environmental threat, African researchers are working to develop and optimize sound sampling and analytical procedures, risk assessment models, and efficient remediation technologies. In this review, related recent research efforts conducted in African universities and research institutions will be presented and discussed with respect to the occurrence and assessment of CECs in African wastewater effluents, the potential risks to aquatic ecosystems and humans, the tailored remediation techniques, along with some knowledge gaps and new research directions.

Impact assessment of a large panel of organic and inorganic micropollutants released by wastewater treatment plants at the scale of France

Micropollutants emitted by Human activities represent a potential threat to our health and aquatic environment. Thousands of active substances are used and go to WWTP through wastewaters. During water treatment, incomplete elimination occurs. Effluents released to the environment still contain part of the micropollutants present in the influents. Here, we studied the potential impacts on Human health and aquatic environment of the release of 261 organic micropollutants and 25 inorganic micropollutants at the scale of France. Data were gathered from national surveys, reports, papers and PhD works. The USEtox ® model was used to assess potential impacts. The impacts on Human health were estimated for 94 organic and 15 inorganic micropollutants and on aquatic environment for 88 organic and 19 inorganic micropollutants highlighting lack of concentration and toxicological data in literature. Some Polycyclic Aromatic Hydrocarbons and pesticides as well as As and Zn showed highest potential impacts on Human health. Some pesticides, PCB 101, βE2, Al, Fe and Cu showed highest potential impacts on aquatic environment.

Removal of trace organic pollutants (pharmaceuticals and pesticides) and reduction of biological effects from secondary effluent by typical granular activated carbon

Residual trace organic pollutants (TOPs) and associated biological effects from secondary effluent (SE) are attracting much attention because of their safety concerns. Granular activated carbon (GAC) adsorption, due to its low cost and high efficiency, is widely applied for further wastewater treatment, but its selective removals of TOPs and biological effects are poorly understood. In the present study, the surface physicochemical characteristics of four types of typical GACs were investigated, and their correlation with luminescent bacteria toxicity was discussed. Based on the biological effect control, shell GAC, with a great adsorption capacity and high functional group contents was selected for further study, including for the removal of fluorescent dissolved organic matter (DOM), 21 TOPs, and 3 biological effects. The shell GAC showed a promising property of removing fluorescent DOM and TOPs. The total concentration of 21 detected TOPs, including 12 pesticides and 9 pharmaceuticals, achieved 82% removal when 30 g/L shell GACs was added. Individual chemicals removal by GAC adsorption was not well described by an individual parameter (e.g., logD, molecular size, charge, functional groups), but rather by a variety of physical and chemical interactions among TOPs, DOM, and GAC. The biological effects from SE were mainly caused by TOPs and DOM. Hence, shell GACs also showed high removal efficiencies of luminescent bacteria toxicity, genotoxicity, and photosynthetic inhibition effect. The removal mechanisms of the three biological effects from SE were deeply discussed. Therefore, the GAC treatment is considered to be one of the most suitable options to ensure the ecological safety of discharged wastewater, because it can effectively control DOM, TOPs, and associated biological effects.

Removal of pharmaceuticals from nitrified urine by adsorption on granular activated carbon

Nitrification and distillation of urine allow for the recovery of all nutrients in a highly concentrated fertilizer solution. However, pharmaceuticals excreted with urine are only partially removed during these two process steps. For a sustainable and safe application, more extensive removal of pharmaceuticals is necessary. To enhance the pharmaceutical removal, which is already occurring during urine storage, nitrification and distillation, an adsorption column with granular activated carbon (GAC) can be included in the treatment train. We executed a pilot-scale study to investigate the adsorption of eleven indicator pharmaceuticals on GAC. During 74 days, we treated roughly 1000 L of pre-filtered and nitrified urine spiked with pharmaceuticals in two flow-through GAC columns filled with different grain sizes. We compared the performance of these columns by calculating the number of treated bed volumes until breakthrough and carbon usage rates. The eleven spiked pharmaceuticals were candesartan, carbamazepine, clarithromycin, diclofenac, emtricitabine, hydrochlorothiazide, irbesartan, metoprolol, N₄-acetylsulfamethoxazole, sulfamethoxazole and trimethoprim. At the shortest empty bed contact time (EBCT) of 25 min, immediate breakthrough was observed in both columns shortly after the start of the experiments. Strong competition by natural organic material (NOM) could have caused the low pharmaceutical removal at the EBCT of 25 min. At EBCTs of 70, 92 and 115 min, more than 660 bed volumes could be treated until breakthrough in the column with fine GAC. The earliest breakthrough was observed for candesartan and clarithromycin. On coarse GAC, only half the number of bed volumes could be treated until breakthrough compared to fine GAC. The probable reason for the later breakthrough with fine GAC is the smaller intraparticle diffusive path length. DOC and UV absorbance measurements at 265 nm indicated that both parameters can be used as indicators for the breakthrough of pharmaceuticals. In contrast to pharmaceuticals and DOC, the nutrient compounds ammonium, nitrate, phosphate, potassium and sulfate were not removed significantly. A comparison with literature values suggests that the amount of GAC needed to remove pharmaceuticals from human excreta could be reduced by nearly two orders of magnitude, if urine were treated on site instead of being discharged and treated in a centralized wastewater treatment plant.

Ozonation in advanced treatment of secondary municipal wastewater effluents for the removal of micropollutants

The objective of this study was the experimental evaluation of ozonation as an additional treatment step for the removal emerging contaminants from secondary effluents of two wastewater treatment plants (WWTPs), one receiving a primarily domestic wastewater (WWTP-A), and the other one domestic sewage together with pretreated tannery wastewater streams (WWTP-B). The experimental runs were conducted at two different pH values (i.e., original pH and adjusted pH of 10) and at six different ozone doses ranging between 0.2 and 1.5 mg O₃/mg DOC. A total of 20 compounds, including 12 micropollutants (MPs) and 8 metabolites, were selected as the target analytes for the evaluation of ozonation performance. When the tested MPs and metabolites were considered individually, the maximum elimination level for each compound was reached at different doses; therefore, optimum ozone doses were determined based on the reduction of the total MP content. Ozonation at the original pH with an ozone dose in the range of 0.4-0.6 and 0.8-1.0 mg O₃/mg DOC was selected as the optimum operating condition for WWTP-A and WWTP-B, respectively, both resulting in an average overall removal efficiency of 55%. Ozone treatment yielded only poor elimination for o-desmethyl naproxen (15%), which was found to be by far the main contributor accounting alone for approximately 30% of the total MP concentration in the secondary effluents. The systematic approach used in this study could well be adopted as a guide to other domestic and municipal WWTPs, which are thought to have a highly variable composition in terms of the MPs and metabolites.

Removal of emerging pollutants in aqueous phase by heterogeneous Fenton and photo-Fenton with Fe2O3-TiO2-clay heterostructures

Fe₂O₃-TiO₂-clay heterostructures have been prepared using an organo-bentonite as support, which organophilic character favored the fixation of TiO₂. Furthermore, Fe₂O₃ was successfully anchored by wet impregnation. The resulting materials are characterized by a disordered layered structure and a mesoporous texture. The heterostructures were employed as catalysts for the removal of two pharmaceuticals, acetaminophen (ACE) and antipyrine (ANT), by heterogeneous Fenton and photo-Fenton processes. ACE removal under different operation conditions was studied in detail to establish structure-performance relationships, being the TiO₂ formation and the developed texture the main factors controlling the activity. ANT showed a higher refractory behavior in oxidation by Fenton. Among the technologies studied, heterogeneous photo-Fenton achieved the best catalytic performance and higher kinetic rate and mineralization degree. Iron leaching was very low, lower than 5% of the initial iron load in all cases. This work demonstrates the potential application of these heterostructures for the removal of emerging pollutants of different nature.

Pre-Treatment Methods for Regeneration of Spent Activated Carbon

Spent activated carbon (SAC) usually exhibits a low specific surface area due to its high ash contents. In this study, pre-treatments, such as heat and acid treatments, were optimized to improve this feature. The heat pre-treatment did not reduce the ash content, nor did it increase the surface area. Because metallic ions adsorbed in SACs turn into ash upon the heat treatment. In the acid pre-treatment, the volatiles and fixed carbon were increased with decreasing ash contents. In this study, it was found that the surface area increase was correlated with the ratio between fixed carbon and ash. Among the pre-treatment methods, the combined heat and acid pre-treatment method highly increased the ratio, and therefore led to the surface area increase. Additionally, the acid pre-treatment was carried out using different types of acid (organic and inorganic acids) solutions to further improve the surface areas. The organic acid treatment caused a significant structural collapse compared to the inorganic acid treatment, decreasing the surface area. In particular, H₃PO₄ effectively removed ashes adsorbed on the activated carbon surface and regenerated the exhausted activated carbon. Both the heat and acid pre-treatments before chemical activation resulted in the positive effects such as strong desorption of pollutants and ashes within the internal structure of the activated carbon. Therefore, the regeneration introduced in this study is methodically the best method to regenerate SAC and maintain a stable structure.

Removal, seasonal variation, and environmental impact of parabens in a municipal wastewater treatment facility in Guangzhou, China

The occurrence, seasonal variation, and environmental impact of five widely used parabens, methyl-(MeP), ethyl-(EtP), n-propyl-(n-PrP), n-butyl-(n-BuP), and benzyl-(BzP) parabens, were investigated in a municipal wastewater treatment plant (WWTP) located in Guangzhou, China, for 1 year. The concentrations of ∑₅parabens in the influent and the effluent were 94.2-957 and 0.89-14.7 ng L^-1, respectively. The influent paraben concentrations in autumn were significantly lower than in winter, spring, and summer, and the concentrations were generally higher in spring. The removal efficiencies of ∑₅parabens in the dissolved phase were over 96%, with high efficiencies in MeP, EtP, and n-PrP. Risk assessment indicated that parabens in the effluent were not likely to pose an environmental risk to aquatic ecosystems. The present study indicates that the treatment processes employed in full-scale WWTPs are effective at removing parabens and highlights the possibility of utilizing WWTPs for restoring water quality in riverine and coastal regions heavily impacted by paraben contamination.

Benefits of ozonation before activated carbon adsorption for the removal of organic micropollutants from wastewater effluents

Advanced processes for the removal of organic micropollutants (OMPs) from wastewater effluents include adsorption onto activated carbon, ozonation, or a combination of both processes. The removal of 28 OMPs present in a real wastewater effluent was studied by ozonation coupled to activated carbon adsorption and compared to a sole adsorption. The influence of the specific ozone dose (0.09-1.29 gO₃/gDOC) and the influence of the powdered activated carbon (PAC) dose (2, 5 and 10 mg/L) were first studied separately. OMPs removal increased with both the specific ozone dose (up to 80% for a dose higher than 0.60 gO₃/gDOC) and the PAC dose. Ozonation performances decreased in presence of suspended solids, which were converted to dissolved organic carbon. A correction of the specific ozone dose according to the suspended solids levels, in addition to nitrite, should be considered. The influence of ozonation (0.09, 0.22, 0.94 and 1.29 gO₃/gDOC) on OMPs adsorption was then assessed. OMPs adsorption didn't change at low specific ozone doses but increased at higher specific ozone doses due to a decrease in DOM adsorption and competition with OMPs. At low ozone doses followed by adsorption (0.22 gO₃/gDOC and 10 mg/L PAC), the two processes appeared complementary as OMPs with a low reactivity toward ozone were well absorbed onto PAC while most OMPs refractory to adsorption were well eliminated by ozone. Improved removals were obtained for all compounds with these selected doses, reaching more than 80% removal for most OMPs while limiting the formation of bromate ion.

Influence of dissolved organic matter on the removal of 12 organic micropollutants from wastewater effluent by powdered activated carbon adsorption

The presence of dissolved organic matter (DOM) in wastewater effluents is recognized as the main factor limiting the adsorption of organic micropollutants (OMPs) onto activated carbon. The degree of the negative effect that DOM, depending on its quality, exerts on OMPs adsorption is still unclear. The influence of the interactions between DOM and OMPs on their removal is also not fully understood. Adsorption isotherms and conventional batch tests were performed in ultra-pure water and in wastewater effluent to study the influence of DOM on the adsorption of 12 OMPs onto powdered activated carbon. Best fit of adsorption pseudo-isotherms was obtained with the Freundlich equation and showed, as expected, that OMPs adsorption was higher in ultra-pure water than in wastewater effluent due to the presence of DOM leading to pore blockage and competition for adsorption sites. LC-OCD analysis revealed that biopolymers and hydrophobic molecules were the most adsorbed fractions while humic acids were not removed after a contact time of either 30 min or 72 h. The presence of DOM had a negative impact on the removal of all OMPs after 30 min of adsorption, but similar removals to ultra-pure water were obtained for 6 OMPs after 72 h of adsorption. This demonstrated that competition between DOM and OMPs for adsorption sites was not a major mechanism as compared to pore blockage, which only slowed down the adsorption and did not prevent it. The charge of OMPs had a clear impact: the adsorption of negatively charged compounds was reduced in the presence of wastewater effluent due to repulsive electrostatic interactions with the adsorbed DOM and the PAC surface. On the other hand, the removal of positively charged compounds was improved. A 24 h pre-equilibrium between OMPs and DOM improved their removal onto PAC, which suggest that OMPs and DOM interacted in solution which decreased the negative effects caused by the presence of DOM, e.g. through co-adsorption of an OMP-DOM complex.

Validation of sampling techniques and SPE-UPLC/MS/MS for home and personal care chemicals in the Songhua Catchment, Northeast China

A method for the simultaneous determination of 18 home and personal care chemicals (HPCCs) in river water and wastewater was developed using solid-phase extraction and ultra-high-performance liquid chromatography with tandem mass spectrometry (SPE and UPLC/MS/MS). A series of tests were designed to find the potential background interference and loss of HPCCs during the sample preservation and pretreatment process. Our results suggested that a considerable amount of some target compounds were lost with increasing days of storage even at 4 °C. Accordingly, the samples were stored acidified and refrigerated, including during transportation, to reduce the losses. Experiments on filtration of water samples suggested that recoveries of many HPCCs were significantly affected by the filtration. It is therefore recommended to avoid filtration of water samples where possible. The internal standard corrected recoveries for the HPCCs ranged from 64.2 to 107.0%, except for benzisothiazolone which did not have an appropriate internal standard, in river water which was considered to be the most difficult matrix. The method detection limits for river water, influent and effluent samples were in the ranges of 0.17 to 42 ng/L, 13 to 5100 ng/L, and 0.50 to 200 ng/L, respectively. The validated method was applied for the determination of HPCCs in sewage water collected from a full-scale wastewater treatment plant (WWTP) in a typical urban city in Northeast China and from river water upstream and downstream of the WWTP. Linear alkylbenzene sulphonate, caffeine, methyl paraben, benzalkonium chloride, triclocarban, and triclosan were the major compounds detected in the river water and wastewater samples. Sampling variability for the WWTP (intra-day and inter-day) and cross-river was also determined with the purpose of designing future monitoring requirements. Small variations in these samples confirmed that composite samples and a single sampling event would be representative for future use.

Influence of the properties of 7 micro-grain activated carbons on organic micropollutants removal from wastewater effluent

Most studies dedicated to organic micropollutants (OMPs) removal from wastewater effluents by adsorption onto activated carbon (AC) only consider a few conventional AC properties. The link between OMPs removal and these properties is often missing, which limits the understanding of the adsorption process and the interpretation of the results. The chemical, physical and textural properties of seven newly commercialized micro-grain activated carbons (μGACs) were determined to assess their influence on the removal of 28 OMPs. Conventional batch tests with wastewater effluent showed that a high percentage of microporous volume (>65%) was detrimental for the removal of 10 OMPs, probably due to a higher blockage of micropores by dissolved organic matter (DOM). The removal of 5 OMPs was correlated with μGACs surface chemistry properties (i.e. charge) which were potentially modified by DOM adsorption or inorganic species, thus favoring the adsorption of positively-charged compounds. A combination of OMPs properties including their charge, hydrophobicity and minimal projection area could explain their removal. Correlations were found between the removal of several OMPs and UV₂₅₄, suggesting that DOM and OMPs interacted with each other or followed similar adsorption mechanisms. A decrease in μGACs particle size had a positive impact on UV₂₅₄ removal under continuous-flow conditions in columns representative of a large-scale pilot due to better expansion.

Suspect, non-target and target screening of emerging pollutants using data independent acquisition: Assessment of a Mediterranean River basin

A single workflow based on three approaches (target, suspected and non-target screening) using liquid chromatography coupled to quadrupole-time-of-flight mass spectrometry (LC-QTOF-MS) in data independent acquisition mode (DIA) was developed to assess the presence of emerging pollutants (EPs) in water and sediments from a Mediterranean River Basin. Identification of potential contaminants was based on mass accuracy, isotopic ratio pattern, theoretical fragmentation, and retention time using Waters UNIFI software. In the suspect screening against a library containing 2200 components, 68 contaminants were tentatively identified, 6 of which were confirmed and quantified with analytical standards. Non-target screening (NTS) required additional manual processing and the aid of an on-line database (ChemSpider) to tentatively identify compounds. Eprosartan, an antihypertensive drug not included in the library used for suspected screening, was confirmed and semi-quantified. The identification of Eprosartan proved the workflow to be functional for NTS. Target screening of 171 pesticides and 33 pharmaceuticals and personal care products (PPCPs) including the compounds confirmed using suspect (6) and non target (1) screening achieved monitoring of the most abundant contaminants from the head to the mouth of the Turia basin to establish their spatial distribution. QTOF-MS screening versatility with its high-resolution capability allows for a comprehensive assessment of EPs in the aquatic environment.

Removal of pharmaceuticals and personal care products by two-stage biofiltration for drinking water treatment

Contamination of drinking water with pharmaceuticals and personal care products (PPCPs) is an issue of health concerns. To effectively control the level of PPCPs in drinking water, a pilot study employing two parallel trains of two-stage biofiltration, i.e., a sand/anthracite (SA) biofilter coupled with a biologically-active granular activated carbon (GAC) post-filter contactor, was conducted as a post-treatment after coagulation in a drinking water treatment plant. Results showed the biofiltration process could effectively remove PPCPs with an average removal of 53.4%, where the GAC contactor played the dominant role to remove 48.1% of the total PPCPs. The molecular properties determined the removability of individual PPCPs, i.e., smaller molecules with simpler structure connectivity were more likely to be removed. Based on the quantitative structure-property relationships (QSPRs) analysis, a simple regression model was proposed to predict the removability of each PPCP across the biofiltration process. The drinking water equivalent level (DWEL) quotient method was developed to assess the health risks of detected PPCPs in water samples. The biofiltration process showed efficient capacity to reduce the health risks of PPCPs with an average removal of 79%, and the PPCPs in the effluents generally would not pose adverse health effects. Pearson correlation analysis explored the possible role of nitrogenous PPCPs (N-PPCPs) as the precursors of nitrogenous disinfection byproducts (N-DBPs) in drinking waters. Aromatic nitrogen in PPCPs was found to be a significant descriptor for the formation potential of trichloroacetonitrile (TCAN). In addition, it was found that pre-filter chlorination could slightly improve the biofiltration of PPCPs.

Pharmaceutical emerging pollutants removal from water using powdered activated carbon: Study of kinetics and adsorption equilibrium

Pharmaceutical products and their byproducts which are present in wastewater and superficial water are becoming an environmental problem. A large effort has been made to introduce new and more efficient treatment processes for removing these emerging pollutants. Among them, activated carbon is currently being studied to be implemented in wastewater treatment plants. In the present study the equilibrium and kinetics of the adsorption of carbamazepine (Cbz) and sildenafil citrate (Sil) onto powdered activated carbon are presented. Batch experiments were performed to assess the potential of this kind of activated carbon for removing these recalcitrant pharmaceuticals from aqueous systems. In addition, its adsorption efficiency was compared with the granular activated carbon. The isotherms of Langmuir, Freundlich, Langmuir-Freundlich and Redlich-Peterson were applied. Pseudo-first and pseudo-second order models, as well as a combined model and an intraparticle diffusion model were assayed on the results obtained. Linear and non-linear analyses were carried out to compare the best fitting isotherms and kinetics. The Langmuir isotherm was a good fit for the adsorption of Sil, whereas the Redlich-Peterson isotherm described the adsorption of Cbz. The experimental results for both pharmaceuticals follow a kinetic of pseudo first order. Comparative studies preparing the solutions with distilled water, dechlorinated water and wastewater were performed. No significant differences were observed in these studies. When initial concentrations similar to those found in surface waters for both pharmaceuticals were evaluated, removal efficiencies greater than 85% were obtained. Therefore, the use of this kind of activated carbon seems to be an efficient tool for the removal of recalcitrant emerging pollutants, such as Sil and Cbz.

Organic micropollutants in a large wastewater treatment plant: What are the benefits of an advanced treatment by activated carbon adsorption in comparison to conventional treatment?

Several advanced treatments, such as ozonation or activated carbon adsorption, are currently considered for the removal of organic micropollutants (OMPs) in wastewater treatment plants (WWTP). However, little is known on the overall performances of a WWTP upgraded with those processes and the benefits provided regarding the elimination of multiple families of OMPs. In this study, 5 sampling campaigns were performed to determine the removal of 48 OMPs in a WWTP followed by an activated carbon pilot. The primary treatment had no effect on OMPs (removals < 20%), whereas the biological treatment removed OMPs that can be easily sorbed onto sludges or biodegraded (>60%). The additional elimination provided by the advanced treatment was not significant (<10%) for OMPs already well removed in the WWTP) but was substantial (>30%) for recalcitrant OMPs. Removals higher than 60% were obtained for all OMPs (except azithromycin and sulfamethoxazole) over the WWTP and the activated carbon pilot. The adsorption conditions (10 g/m³ fresh activated carbon addition) were not sufficient to achieve the 80% removal targeted in Switzerland for compounds suggested as indicator substances for wastewater treatment. A higher dose of activated carbon or the combination with another advanced treatment should be used to achieve a satisfactory removal of those compounds.

Porous Polymers as Multifunctional Material Platforms toward Task-Specific Applications

Exploring advanced porous materials is of critical importance in the development of science and technology. Porous polymers, being famous for their all-organic components, tailored pore structures, and adjustable chemical components, have attracted an increasing level of research interest in a large number of applications, including gas adsorption/storage, separation, catalysis, environmental remediation, energy, optoelectronics, and health. Recent years have witnessed tremendous research breakthroughs in these fields thanks to the unique pore structures and versatile skeletons of porous polymers. Here, recent milestones in the diverse applications of porous polymers are presented, with an emphasis on the structural requirements or parameters that dominate their properties and functionalities. The Review covers the following applications: i) gas adsorption, ii) water treatment, iii) separation, iv) heterogeneous catalysis, v) electrochemical energy storage, vi) precursors for porous carbons, and vii) other applications (e.g., intelligent temperature control textiles, sensing, proton conduction, biomedicine, optoelectronics, and actuators). The key requirements for each application are discussed and an in-depth understanding of the structure-property relationships of these advanced materials is provided. Finally, a perspective on the future research directions and challenges in this field is presented for further studies.

Non-target strategies by HRMS to evaluate fluidized micro-grain activated carbon as a tertiary treatment of wastewater

Among the release solutions for reducing the discharge of organic and persistent contaminants in the aquatic environment, the use of a tertiary treatment in addition to existing conventional wastewater treatment processes is considered. The use of micro-grain activated carbon in a fluidized bed is a promising technique investigated in this study. The effluents from a large-scale pilot system were analyzed by liquid chromatography coupled with high-resolution mass spectrometry (QToF). Several strategies were deployed, namely molecular fingerprint comparison, suspected and non-target analyses, identification of refractory compounds to treatment, and finally, quantification of identified compounds. The evaluation of the molecular fingerprints provided evidence of the overall effect of the tertiary treatment on the treated wastewater quality. The suspected approach highlighted the presence of 83 pharmaceuticals and pesticides as well as transformation products in the effluents. The non-target approaches also highlighted compounds refractory to tertiary treatment, such as illicit drugs or some pharmaceuticals. The identification and quantification of identified compounds underscored the suitability of micro-grain activated carbon in eliminating many classes of pharmaceuticals with various physicochemical properties, such as anti-hypertensive, analgesic, anti-viral, antidepressant and even various pesticides.

Influencing factors on the removal of pharmaceuticals from water with micro-grain activated carbon

The removal efficiency of 6 micro-grain AC (μGAC) was examined for 23 selected pharmaceutical compounds, usually found at trace level in municipal wastewater treatment plant (WWTP) effluents. Two different sets of experiments were carried out using distilled water and a real WWTP secondary effluent in order to understand the adsorption mechanisms of pharmaceuticals, including the role of the presence of background organic matter. Physical and chemical properties of μGACs and target pollutants were checked for their potential to predict the pharmaceutical removal. Textural properties of μGACs, and especially the mesopore volume, seemed to play the most important role during the adsorption without background organic matter whereas the chemistry of the μGACs, such as the presence of surface oxygen groups and the point of zero charge, could have more influence in the experiments with WWTP effluent water. Positively charged molecules are better adsorbed due to the influence of the background organic matter and the presence of oxygenated groups in the surface of the μGACs. The UV₂₅₄ removal correlated well with the pharmaceutical removal and it is confirmed as an indicator to control the performance of pharmaceuticals adsorption with μGACs in tertiary treatment.

Wastewater chemical contaminants: remediation by advanced oxidation processes

Approximately 70% of the terrestrial area is covered with water, but only a small water fraction is compatible with terrestrial life forms. Due to the increment in human consumption, the need for water resources is increasing, and it is estimated that more than 40% of the population worldwide will face water stress/scarcity within the next few decades. Water recycling and reuse may offer the opportunity to expand water resources. For that, the wastewater treatment paradigm should be changed and adequately treated wastewater should be seen as a valuable resource instead of a waste product. It is easily understandable that the exact composition and constituent concentration of wastewater vary according to its different sources (industrial, agricultural, urban usage of water). Consequently, a variety of known and emerging pollutants like heavy metals, antibiotics, pesticides, phthalates, polyaromatic hydrocarbons, halogenated compounds and endocrine disruptors have been found in natural water reservoirs, due to the limited effectiveness of conventional wastewater treatment. The conventional approach consists of a combination of physical, chemical and biological processes, aiming at the removal of large sediments such as heavier solids, scum and grease and of organic content in order to avoid the growth of microorganisms and eutrophication of the receiving water bodies. However, this approach is not sufficient to reduce the chemical pollutants and much less the emerging chemical pollutants. In this review, after some considerations concerning chemical pollutants and the problematic efficiency of their removal by conventional methods, an update is presented on the successes and challenges of novel approaches for wastewater remediation based on advanced oxidation processes. An insight into wastewater remediation involving the photodynamic approach mediated by tetrapyrrolic derivatives will be underlined.