Recycled desalination membranes as a support material for biofilm development: A new approach for microcystin removal during water treatment

Eco-friendly management of harmful cyanobacterial blooms in eutrophic lakes through vertical flow multi-soil-layering technology

Eutrophication has led to the widespread occurrence of cyanobacterial blooms. Toxic cyanobacterial blooms with high concentrations of microcystins (MCs) have been identified in the Lalla Takerkoust reservoir in Morocco. The objective of this study was to evaluate the efficiency of the Multi-Soil-Layering (MSL) ecotechnology in removing natural cyanobacterial blooms from the lake. Two MSL pilots were used in rectangular glass tanks (60 × 10 × 70 cm). They consisted of permeable layers (PLs) made of pozzolan and a soil mixture layer (SML) containing local soil, ferrous metal, charcoal and sawdust. The main difference between the two systems was the type of local soil used: sandy soil for MSL1 and clayey soil for MSL2. Both MSL pilots effectively reduced cyanobacterial cell concentrations in the treated water to very low levels (0.09 and 0.001 cells/mL). MSL1 showed a gradual improvement in MC removal from 52 % to 99 %, while MSL2 started higher at 90 % but dropped to 54% before reaching 86%. Both MSL systems significantly reduced organic matter levels (97.2 % for MSL1 and 95.8 % for MSL2). Both MSLs were shown to be effective in removing cyanobacteria, MCs, and organic matter with comparable performance.

Reusable and Practical Biocomposite Based on Sphingopyxis sp. YF1 and Polyacrylonitrile-Based Carbon Fiber for the Efficient Bioremediation of Microcystin-LR-Contaminated Water

Microbial degradation is a cost-effective and environmentally friendly method for removing microcystin-LR (MC-LR). However, the application of free bacteria has limitations due to low operational stability and difficulties in recovery. In a previous study, our group successfully isolated a highly efficient MC-LR-degrading bacterium, Sphingopyxis sp. YF1, from Taihu. To enhance its practical potential in addressing MC-LR-contaminated water pollution, a novel biological material named polyacrylonitrile-based carbon fiber @Sphingopyxis sp. YF1 (PAN-CF@YF1) was synthesized. The immobilization conditions of strain Sphingopyxis sp. YF1 on PAN-CF surfaces were optimized using Box-Behnken design and response surface methodology (RSM), which turned out to be an optimal pH of 7.6 for the culture medium, a ratio of 0.038 g of supporting materials per 100 mL of culture media, and an incubation time of 53.4 h. The resultant PAN-CF@YF1 showed a great degradation effect both for low and high concentrations of MC-LR and exhibited satisfactory cyclic stability (85.75% after six cycles). Moreover, the application of PAN-CF@YF1 in the bioreactors demonstrated effective and sustainable MC-LR removal, with a removal efficiency of 78.83% after three consecutive treatments. Therefore, PAN-CF@YF1 with high degradation activity, environmental compatibility, straightforward preparation, and recyclability shows significant application potential for the bioremediation of MC-LR-contaminated water bodies.

Impacts of algal organic matter and humic substances on microcystin-LR removal and their biotransformation during the biodegradation process

The application of bioaugmentation (i.e., injection of contaminant-degrading microorganisms) has shown its potential to remove harmful cyanotoxins like microcystin-LR (MC-LR) from drinking water sources. However, the natural organic matter (NOM) present in both natural and engineered water systems might affect the bacterial biodegradation of MC-LR. Therefore, for the successful application of bioaugmentation for MC-LR removal in water treatment, it is important to understand NOM effects on MC-LR biodegradation. In this study, the impact of NOM [algal organic matter (AOM) and humic substances (HS)] on MC-LR biodegradation was evaluated in the presence of varying concentrations of NOM by monitoring MC-LR biodegradation kinetics. The changes in NOM composition during MC-LR biodegradation were also characterized by a five-component Parallel factor (PARAFAC) model using 336 excitation-emission matrix (EEM) spectra collected at different sampling points. Our results showed decreases in MC-LR biodegradation rate of 1.6-and 3.4-fold in the presence of AOM and HS, respectively. The expression of the functional mlrA gene exhibited a similar trend to the MC-LR degradation rate at different NOM concentrations. EEM-PARAFAC analyses and NOM molecular size fractionation results indicated a relatively greater production of terrestrial humic-like components (57%) and a decrease of protein-like components. Two-dimensional correlation spectroscopy (2D-COS) analyses further confirmed that low molecular weight protein-like components were initially utilized by bacteria, followed by the formation of higher molecular weight humic-like components, likely due to microbial metabolism.

Thin Film Composite Polyamide Reverse Osmosis Membrane Technology towards a Circular Economy

It is estimated that Reverse Osmosis (RO) desalination will produce, by 2025, more than 2,000,000 end-of-life membranes annually worldwide. This review examines the implementation of circular economy principles in RO technology through a comprehensive analysis of the RO membrane life cycle (manufacturing, usage, and end-of-life management). Future RO design should incorporate a biobased composition (biopolymers, recycled materials, and green solvents), improve the durability of the membranes (fouling and chlorine resistance), and facilitate the recyclability of the modules. Moreover, proper membrane maintenance at the usage phase, attained through the implementation of feed pre-treatment, early fouling detection, and membrane cleaning methods can help extend the service time of RO elements. Currently, end-of-life membranes are dumped in landfills, which is contrary to the waste hierarchy. This review analyses up to now developed alternative valorisation routes of end-of-life RO membranes, including reuse, direct and indirect recycling, and energy recovery, placing a special focus on emerging indirect recycling strategies. Lastly, Life Cycle Assessment is presented as a holistic methodology to evaluate the environmental and economic burdens of membrane recycling strategies. According to the European Commission's objectives set through the Green Deal, future perspectives indicate that end-of-life membrane valorisation strategies will keep gaining increasing interest in the upcoming years.

Immobilization of Microbes for Biodegradation of Microcystins: A Mini Review

Harmful cyanobacterial blooms (HCBs) frequently occur in eutrophic freshwater ecosystems worldwide. Microcystins (MCs) are considered to be the most prominent and toxic metabolites during HCBs. MCs may be harmful to human and animal health through drinking water and recreational water. Biodegradation is eco-friendly, cost-effective and one of the most effective methods to remove MCs. Many novel MC-degrading bacteria and their potential for MCs degradation have been documented. However, it is a challenge to apply the free MC-degrading bacterial cells in natural environments due to the long-term operational instability and difficult recycling. Immobilization is the process of restricting the mobility of bacteria using carriers, which has several advantages as biocatalysts compared to free bacterial cells. Biological water treatment systems with microbial immobilization technology can potentially be utilized to treat MC-polluted wastewater. In this review article, various types of supporting materials and methods for microbial immobilization and the application of bacterial immobilization technology for the treatment of MCs-contaminated water are discussed. This article may further broaden the application of microbial immobilization technology to the bioremediation of MC-polluted environments.

Steel pickling rinse wastewater treatment by two-stage MABR system: Reactor performance, extracellular polymeric substances (EPS) and microbial community

A bench-scale two-stage membrane-aerated biofilm reactor (MABR) system was applied to treat steel pickling rinse wastewater with high salinity and refractory organic. The effects of salinity and aeration pressure on the treatment efficiency, extracellular polymeric substances (EPS) characteristics and microbial community structure were studied. The optimal removal efficiencies of COD, NH+ 4-N and TN reached to 62.84%, 99.57% and 51.65%, respectively. Shortcut nitrification was achieved at low aeration, and the salinity less than 4% did not remarkable affect system performance. Colorimetric determination, three-dimensional exaction-emission matrix (3D-EEM) and Fourier transform infrared spectrum (FTIR) were employed to characterize the content and composition of proteins (PN) and polysaccharides (PS) in EPS of the biofilm. The results indicated that PN, not PS, response to changes of environmental conditions played a key role. Moreover, EPS might alleviate intracellular and extracellular osmotic pressure imbalance induced by high salinity, which imparted the biofilm in MABR with prominent salt-tolerant. High-throughput sequencing displayed that nitrifiers (Nitrosomonas, Nitrospira), denitrifiers (Dechloromonas, Hyphomicrobium, Denitromonas, Denitratisoma, Candidatus_Competibacter) and aerobic denitrifiers (Pseudomonas, Thauera) were predominant salt-tolerant bacteria.

Biochar-amended constructed wetlands for eutrophication control and microcystin (MC-LR) removal

Microcystins (MCs) pollution caused by eutrophication and climate change has posed a serious threat to ecosystems and human health. Constructed wetlands (CWs) with biochar addition volume ratios of 0% (BC0-CWs), 10% (BC10-CWs), 20% (BC20-CWs) and 50% (BC50-CWs) were set up to evaluate the efficiency of biochar-amended CWs for eutrophication and MCs pollution control. The results illustrated that removal efficiencies of both NH₄⁺-N and NO₃^--N were enhanced by biochar addition to varying degrees. The average TP and MC-LR removal efficiencies increased with increasing biochar addition ratios, and the average TP and MC-LR removal efficiencies in biochar-amended CWs were significantly (p < 0.05) improved by 5.64-9.58% and 10.74-14.52%, respectively, compared to that of BC0-CWs. Biochar addition changed the microbial community diversity and structure of CWs. The relative abundance of functional microorganisms such as Burkholderiaceae, Nitrospiraceae, Micrococcaceae, Sphingomonadaceae and Xanthomonadaceae was promoted by biochar addition regardless of addition ratios. The higher relative abundance of the above microorganisms in BC20-CWs and BC50-CWs may contribute to their better removal performance compared to other CWs. The concentrations of extracellular polymeric substance (EPS) in biochar-amended CWs were significantly (p < 0.05) lower than that in BC0-CWs, which can reduce the risk of system clogging. This study demonstrated that biochar addition may be a potential intensification strategy for eutrophication and MCs pollution control by CWs. Considering both the removal performance and economic cost, a biochar addition ratio of 20% was recommended as an optimal addition ratio in practical application.

Removal of microcystin (MC-LR) in constructed wetlands integrated with microbial fuel cells: Efficiency, bioelectricity generation and microbial response

Microcystins (MCs) pollution caused by cyanobacteria harmful blooms (CHBs) has posed short- and long-term risks to aquatic ecosystems and public health. Constructed wetlands (CWs) have been verified as an effective technology for eutrophication but the removal performance for MCs did not achieve an acceptable level. CWs integrated with microbial fuel cell (MFC-CWs) were developed to intensify the nutrient and Microcystin-LR (MC-LR) removal efficiencies in this study. The results indicated that closed-circuit MFC-CWs (T1) exhibited a better NO₃^--N, NH₄⁺-N, TP and MC-LR removal efficiency compared to that of open-circuit MFC-CWs (CK, i.e., traditional CWs). Therein, a MC-LR removal efficiency of greater than 95% was observed in both trials in T1. The addition of sponge iron to the anode layer of MFC-CWs (T2) improved only the NO₃^--N removal and efficiency bioelectricity generation performance compared to T1, and the average effluent MC-LR concentration of T2 (1.14 μg/L) was still higher than the provisional limit concentration (1.0 μg/L). The microbial community diversity of T1 and T2 was simplified compared to CK. The relative abundance of Sphingomonadaceae possessing the degradation capability for MCs increased in T1, which contributed to the higher MC-LR removal efficiency compared to CK and T2. While the relative abundance of electrochemically active bacteria (EAB) (i.e., Desulfuromonadaceae and Desulfomicrobiaceae) in the anode of T2 was promoted by the addition of sponge iron. Overall, this study suggests that integrating MFC into CWs provides a feasible intensification strategy for eutrophication and MCs pollution control.

Studies of the liposolubility and the ecotoxicity of MC-LR degradation by-products using computational molecular modeling and in-vivo tests with Chlorella vulgaris and Daphnia magna

Computational molecular modelling, mass spectrometry and in-vivo tests with Chlorella vulgaris (C. vulgaris) and Daphnia magna (D. magna) were used to investigate the liposolubility and ecotoxicity of MC-LR degradation by-products generated after oxidation by OH^• radicals in Fenton process. Exposure of MC-LR (5 µg.L^-1) to the most severe oxidation conditions (Fe²⁺ 20 mM and H₂O₂ 60 mM) resulted in a reduction in the toxin concentration of 96% (0.16 µg.L^-1), however, with the formation of many by-products. The by-product of m/z 445 was the most resistant to degradation and retained a toxic structure of diene bonds present in the Adda amino acid. Computational modeling revealed that m/z 445 (tPSA = 132.88 Ų; KOW = 2.02) is more fat-soluble than MC-LR (tPSA = 340.64 Ų; KOW = 0.68), evidencing an easier transport process of this by-product. Given this, toxicity tests using C. vulgaris and D. magna indicated greater toxicity of the by-product m/z 445 compared to MC-LR. When the conversion of MC-LR to by-products was 77%, the growth inhibition of C. vulgaris and the D. magna immobility were, respectively, 6.14 and 0%, with 96% conversion; growth inhibition and the immobility were both 100%  for both species.

A Novel Application of Recycled Ultrafiltration Membranes in an Aerobic Membrane Bioreactor (aMBR): A Proof-of-Concept Study

The use of recycled ultrafiltration (r-UF) membranes, originating from end-of-life reverse osmosis membranes, as submerged flat-sheet membranes in an aerobic membrane bioreactor (aMBR) system is described herein for the first time. A feasibility study of this new approach was performed in a laboratory-scale aMBR system. The r-UF membrane performance was evaluated in terms of permeability, fouling behavior, and permeate quality using a widely used commercial flat sheet microfiltration membrane (c-MF) as a reference. Tests were conducted under steady-flux operation (at 12 and 14 L·m⁻²·h⁻¹) and a variable trans-membrane pressure. Synthetic wastewater simulating urban wastewater characteristics with approx. 0.4–0.5 g/L COD concentration was used as the feed. The obtained results showed that the rejection performance of the r-UF membrane was similar to the performance of the commercial flat sheet microfiltration membrane (c-MF) under comparable operating conditions. Moreover, concerning fouling behavior, the r-UF membrane exhibited higher fouling resistance compared with the c-MF membrane, although the permeability decline rate was lower. Both membranes had comparable fouling mechanisms behavior, with cake layer fouling resistance accounting for approx. 60% of the total fouling resistance. Finally, a preliminary economic assessment pointed out the potential competitiveness of using r-UF membranes for aMBRs (5.9–10.9 EUR·m⁻²) and the scaling-up challenges toward industrial applications.

Modeling and optimization of process parameters of biofilm reactor for wastewater treatment

The efficiency of heavy metal in biofilm reactors depends on absorption process parameters, and those relationships are complicated. This study explores artificial neural networks (ANNs) feasibility to correlate the biofilm reactor process parameters with absorption efficiency. The heavy metal removal and turbidity were modeled as a function of five process parameters, namely pH, temperature(°C), feed flux(ml/min), substrate flow(ml/min), and hydraulic retention time(h). We developed a standalone ANN software for predicting and analyzing the absorption process in handling industrial wastewater. The model was tested extensively to confirm that the predictions are reasonable in the context of the absorption kinetics principles. The model predictions showed that the temperature and pH values are the most influential parameters affecting absorption efficiency and turbidity.

Electrospun Nanostructured Membrane Engineering Using Reverse Osmosis Recycled Modules: Membrane Distillation Application

As a consequence of the increase in reverse osmosis (RO) desalination plants, the number of discarded RO modules for 2020 was estimated to be 14.8 million annually. Currently, these discarded modules are disposed of in nearby landfills generating high volumes of waste. In order to extend their useful life, in this research study, we propose recycling and reusing the internal components of the discarded RO modules, membranes and spacers, in membrane engineering for membrane distillation (MD) technology. After passive cleaning with a sodium hypochlorite aqueous solution, these recycled components were reused as support for polyvinylidene fluoride nanofibrous membranes prepared by electrospinning technique. The prepared membranes were characterized by different techniques and, finally, tested in desalination of high saline solutions (brines) by direct contact membrane distillation (DCMD). The effect of the electrospinning time, which is the same as the thickness of the nanofibrous layer, was studied in order to optimize the permeate flux together with the salt rejection factor and to obtain robust membranes with stable DCMD desalination performance. When the recycled RO membrane or the permeate spacer were used as supports with 60 min electrospinning time, good permeate fluxes were achieved, 43.2 and 18.1 kg m⁻² h⁻¹, respectively; with very high salt rejection factors, greater than 99.99%. These results are reasonably competitive compared to other supported and unsupported MD nanofibrous membranes. In contrast, when using the feed spacer as support, inhomogeneous structures were observed on the electrospun nanofibrous layer due to the special characteristics of this spacer resulting in low salt rejection factors and mechanical properties of the electrospun nanofibrous membrane.

Research Progress on Synthesis and Application of Cyclodextrin Polymers

Cyclodextrins (CDs) are a series of cyclic oligosaccharides formed by amylose under the action of CD glucosyltransferase that is produced by Bacillus. After being modified by polymerization, substitution and grafting, high molecular weight cyclodextrin polymers (pCDs) containing multiple CD units can be obtained. pCDs retain the internal hydrophobic-external hydrophilic cavity structure characteristic of CDs, while also possessing the stability of polymer. They are a class of functional polymer materials with strong development potential and have been applied in many fields. This review introduces the research progress of pCDs, including the synthesis of pCDs and their applications in analytical separation science, materials science, and biomedicine.

Treatment of microcystin (MC-LR) and nutrients in eutrophic water by constructed wetlands: Performance and microbial community

Cyanobacterial harmful algal blooms and microcystins (MCs) pollution pose serious threat to aquatic ecosystem and public health. Planted and unplanted constructed wetlands (CWs) filled with four substrates (i.e., gravel (G-CWs), ceramsite (C-CWs), iron-carbon (I-CWs) and slag (S-CWs)) were established to evaluate nutrients and a typical MCs variant (i.e., MC-LR) removal efficiency from eutrophic water affected by the presence of plant and different substrate. The response of the microbial community to the above factors was also analyzed in this study. The results indicate that the presence of plant can generally enhance nutrients and MC-LR removal efficiency in CWs, except for I-CWs. Throughout the experiment, all CWs exhibited good nitrogen removal efficiency with removal percentages exceeding 90%; TP and MC-LR average removal efficiency of C-CWs and I-CWs were greater than G-CWs and S-CWs irrespective of the presence of plant. The best MC-LR removal efficiency under different MC-LR loads was observed in planted C-CWs (ranged from 91.56% to 95.16%). Except for I-CWs, the presence of plant can enhance relative abundances of functional microorganisms involved in nutrients removal (e.g., Comamonadaceae and Planctomycetaceae) and MCs degradation (e.g., Burkholderiaceae). The microbial community diversity of I-CWs was simplified, while the relative abundance of Proteobacteria was highest in this study. The highest relative abundances of Comamonadaceae, Planctomycetaceae and Burkholderiaceae were observed in planted C-CWs. Overall, ceramisite and iron-carbon were more suitable to be applied in CWs for nutrients and MC-LR removal. This study provides a theoretical basis for practical application of CWs in eutrophication and MCs pollution control.

Exploring microcystin-degrading bacteria thriving on recycled membranes during a cyanobacterial bloom

Microcystins (MC) are highly toxic secondary metabolites produced by cyanobacterial blooms in many freshwater ecosystems used for recreational and drinking water purposes. So far, biological processes remain to be optimized for an efficient cyanotoxin removal, and new approaches are necessary to compete with physical-chemical treatments. In previous studies we provided a new concept of membrane biofilm reactor made of recycled material, in which a single MC-degrading bacterial strain was inoculated. The present study evaluates the capacity of bacterial consortia associated with freshwater cyanobacterial blooms to form biofilms on recycled membranes and remove MC. Three different discarded reverse osmosis (RO) membranes, previously used in desalination plants after treating brackish water (BWd), seawater (SWd) and brackish water but transformed into nanofiltration (BWt-NF), were exposed to a cyanobacterial bloom in San Juan reservoir (central Spain). Results showed that the three recycled membranes developed a bacterial community with MC removal capacity. Little differences in bacterial coverage and MC removal efficiency between membranes were observed after their exposure in the reservoir. High-throughput sequencing of 16S rRNA gene analysis showed similar bacterial community composition at the phylum level but dissimilar at the order level between the three membranes. This suggests possible surface selectivity on the attached bacterial community. The mlr^- candidates such as Burkholderiales and Methylophilales were highly abundant in BWt-NF and BWd, respectively, while mlr⁺ candidates (e.g. Sphingomonadales) were low abundant in all membranes. Analysis of mlrA and mlrB genes used as markers for MC degradation following mlr-pathway confirmed the presence of this pathway in all membranes. These results suggest the co-existence of both genotypes in membrane-attached native biofilms. Therefore, this study confirms that recycled membranes are suitable support for many MC-degrading bacteria, thus giving value to discarded membranes for eco-friendly and low-cost biological filters.

Influence of acid/base activation treatment in the performance of recycled electromembrane for fresh water production by electrodialysis

In this study, an activation treatment for recycled anion exchange membranes is proposed. Following the circular economy approach, these membranes were prepared by using end-of-life reverse osmosis membranes as mechanical support. The end-of-life membrane was previously used and discarded by desalination plants after overcoming its lifespan. The activation treatment was based on the subsequent immersion of the membranes in diluted acid and alkali solutions. This treatment promoted the complete dissociation of the functional groups in the membrane, making them more reactive to the counter ions. The effects of acid and alkali concentrations and exposition times on the electrochemical properties were studied and the best combination was selected. In such a way, a decrease of 37% in membrane electrical resistance was achieved. The performance of activated and non-activated membranes in brackish water desalination by electrodialysis was compared. The results showed that the proposed activation treatment increased the flux of fresh water more than four-fold (from 1.2 to 4.9 L h^-1·m^-2), with a considerable reduction of energy consumption (from 5.2 to 3.0 kWh·m^-3) and a great improvement in current efficiency (from 38% to 71%). In conclusion, this work shows a simple and low cost methodology for the improvement of the electrochemical properties of recycled electromembranes and thus, their performance in electrodialysis.

Design and optimization of a new reactor based on biofilm-ceramic for industrial wastewater treatment

A biofilm reactor was designed with flat ceramic substrates to remove Co(II), Ni(II) and Zn(II) from industrial wastewater. The ceramics were made of clay and nano-rubber with high mechanical resistance. The surface of the ceramic substrate was modified with neutral fiber and nano-hydroxyapatite. A uniform and stable biofilm mass of 320 g with 2 mm of thickness was produced on the modified ceramic after 3 d. The micro-organisms were identified in the biofilm by polymerase chain reaction (PCR) method. Functional groups of biofilms were identified with a Fourier transform infrared spectrometer (FT-IR). Experiments were designed by central composite design (CCD) using the responsive surface method (RSM). The biosorption process was optimized at pH = 5.8, temperature = 22 °C, feed flux of heavy metal wastewater = 225 ml, substrate flow = 30 ml, and retention time = 7.825 h. The kinetic data was analyzed by pseudo first-order and pseudo second-order kinetic models. Isotherm models and thermodynamic parameters were applied to describe the biosorption equilibrium data of the metal ions on the biofilm-ceramic. The maximum biosorption efficiency and capacity of heavy metal ions were about 72% and 57.21 mg, respectively.

Recycling of end-of-life reverse osmosis membranes for membrane biofilms reactors (MBfRs). Effect of chlorination on the membrane surface and gas permeability

Reducing human impacts on drinking water is one of the main challenges for the water treatment industry. This work provides new results to support the recycling of EoL desalination reverse osmosis (RO) membranes for Membranes Biofilm Reactors (MBfRs). We investigate if the controlled-removal of fouling and polyamide layer may favor the use of these membranes in MBfRs. It also would allow establishing a normalized methodology of membrane recycling, regardless of inherited fouling during its lifespan. For this purpose, we transform by chlorination discarded brackish (BWd) and seawater (SWd) membranes into nanofiltration (BWt-NF and SWt-NF) and ultrafiltration (BWt-UF and SWt-UF) membranes. Our results show that chlorine attacks allow the fouling cleaning while improves the hydrophilicity and maintains roughness only in BWt-NF. Therefore, the bacterial deposition in this membrane is greater than the other tested membranes. Besides, the microcystin (MC) degradation capacity of BWt-NF verifies the compatibility of the chemical modification for the biological activity of MC-degrading bacteria. Finally, our results also provide that polyamide thin-film composite (PA-TFC) membranes, originally manufactured for salt rejection during desalination processes, offer competitive gases diffusion at low pressures. Therefore, we conclude that the membrane recycling may provide alternative low cost and gas permeable membranes for MBfRs, according to circular economy principles.