Characteristics and mechanisms of chlorpyrifos and chlorpyrifos-methyl adsorption onto biochars: Influence of deashing and low molecular weight organic acid (LMWOA) aging and co-existence

Agricultural biomass/waste-based materials could be a potential adsorption-type remediation contributor to environmental pollution induced by pesticides-A critical review

The widespread use of pesticides that are inevitable to keep the production of food grains brings serious environmental pollution problems. Turning agricultural biomass/wastes into materials addressing the issues of pesticide contaminants is a feasible strategy to realize the reuse of wastes. Several works summarized the current applications of agricultural biomass/waste materials in the remediation of environmental pollutants. However, few studies systematically take the pesticides as an unitary target pollutant. This critical review comprehensively described the remediation effects of crop-derived waste (cereal crops, cash crops) and animal-derived waste materials on pesticide pollution. Adsorption is considered a superior and highlighted effect between pesticides and materials. The review generalized the sources, preparation, characterization, condition optimization, removal efficiency and influencing factors analysis of agricultural biomass/waste materials. Our work mainly emphasized the promising results in lab experiments, which helps to clarify the current application status of these materials in the field of pesticide remediation. In the meantime, rigorous pros and cons of the materials guide to understand the research trends more comprehensively. Overall, we hope to achieve a large-scale use of agricultural biomass/wastes.

Fabrication and characterization of biodegradable hydrogel beads of guar gum for the removal of chlorpyrifos pesticide from water

A new guar gum hydrogel beads were fabricated by dropping method from an aqueous solution of guar gum (GG) using ammonium persulphate and polyethylene glycol as initiator and crosslinker respectively, for the adsorption of chlorpyrifos (CP) from water. The semi-crystalline nature of the synthesized beads was confirmed by FESEM analysis. The TGA studies implied that the beads were thermally stable up to 600 °C. The maximum swelling ratio of 1400 gg-1 was attained at pH 9.2 and 80 min. The evidence of a strong absorption band was found in FTIR spectrum at 584 cm-1 due to -P=S of the adsorbed pesticide CP. The maximum adsorption of CP was found to be 220.97 mgg-1. The adsorption followed pseudo second-order kinetics and Langmuir adsorption isotherm with regression coefficients 0.9998 and 0.9938 which followed the chemisorption process. It is due to the hydrolysis of CP at pH 9.2 to yield 3,5,6-trichloropyridinol which in turn reacts with the carboxylic group present in GG giving -N-C=O linkage. A -ΔG indicates that the process is spontaneous and involves chemisorption which is thermodynamically and kinetically favorable and a -ΔH value (-10.37 kJ/mol) suggests that the adsorption is exothermic.

Emerging technologies for the removal of pesticides from contaminated soils and their reuse in agriculture

Pesticides are becoming more prevalent in agriculture to protect crops and increase crop yields. However, nearly all pesticides used for this purpose reach non-target crops and remain as residues for extended periods. Contamination of soil by widespread pesticide use, as well as its toxicity to humans and other living organisms, is a global concern. This has prompted us to find solutions and develop alternative remediation technologies for sustainable management. This article reviews recent technological developments for remediating pesticides from contaminated soil, focusing on the following major points: (1) The application of various pesticide types and their properties, the sources of pesticides related to soil pollution, their transport and distribution, their fate, the impact on soil and human health, and the extrinsic and intrinsic factors that affect the remediation process are the main points of focus. (2) Sustainable pesticide degradation mechanisms and various emerging nano- and bioelectrochemical soil remediation technologies. (3) The feasible and long-term sustainable research and development approaches that are required for on-site pesticide removal from soils, as well as prospects for applying them directly in agricultural fields. In this critical analysis, we found that bioremediation technology has the potential for up to 90% pesticide removal from the soil. The complete removal of pesticides through a single biological treatment approach is still a challenging task; however, the combination of electrochemical oxidation and bioelectrochemical system approaches can achieve the complete removal of pesticides from soil. Further research is required to remove pesticides directly from soils in agricultural fields on a large-scale.

Advanced technologies in water treatment: Chitosan and its modifications as effective agents in the adsorption of contaminants

Chitosan, derived from the abundant biopolymer chitin, has emerged as a promising option for water treatment due to its intrinsic bioavailability. This review emphasizes the notable characteristics of chitosan, which allow for various modifications, expanding its applications. The polymer's effectiveness in adsorbing contaminants, particularly in advanced water treatment technologies, is highlighted. The review underscores the potential of chitosan-based hybrid materials, including nanocomposites, hydrogels, membranes, films, sponges, nanoparticles, microspheres, and flakes, as innovative alternatives to traditional chemical-based adsorbents. The advantages of using these materials in wastewater treatment, especially in removing heavy metals, dyes, and emerging compounds, are explored. The study delves into the mechanisms involved in wastewater treatment with chitosan, emphasizing the interactions between the polymer and various contaminants. Additionally, the application of chitosan as a contaminant removal agent in a post-pandemic context is addressed, considering the challenges related to waste management and environmental preservation. The analysis highlights the potential contribution of chitosan in mitigating environmental impacts post-pandemic, offering practical solutions for treating contaminated effluents and promoting sustainability. The study addresses current obstacles and prospects for chitosan-based wastewater treatment, emphasizing its promising role in sustainable water management.

Steric and energetic studies on the influence of cellulose on the adsorption effectiveness of Mg trapped hydroxyapatite for enhanced remediation of chlorpyrifos and omethoate pesticides

Magnesium-trapped hydroxyapatite (Mg.HP) was hybridized with cellulose fiber to produce a bio-composite (CLF/HP) with enhanced adsorption affinities for two types of toxic pesticides (chlorpyrifos (CF) and omethoate (OM)). The enhancement influence of the hybridized cellulose on the adsorption performances of Mg.HP was illustrated based on the determined steric and energetic factors. The computed CF and OM adsorption performances of CLF/HP during the saturation phases are 279.8 mg/g and 317.9 mg/g, respectively, which are significantly higher than the determined values using Mg/HP (143.4 mg/g (CF) and 145.3 mg/g (OM)). The steric analysis demonstrates a strong impact of the hybridization process on the reactivity of the surface of the composite. While CLF/HP reflects effective uptake site densities (Nm) of 93.3 mg/g (CF) and 135.3 mg/g (OM), the estimated values for Mg.HP are 51.2 mg/g (CF) and 46.11 mg/g (OM), which explain the reported enhancement in the adsorption performances of the composite. The capacity of each uptake site to be occupied with more than one molecule (n (CF) = 3-3.74 and n (OM) = 2.35-3.54) suggests multimolecular uptake. The energetic factors suggested physical mechanistic processes of spontaneous and exothermic behaviors either during the uptake of CF or OM.

Biotoxicity attenuation and the underlying physicochemical mechanism of biochar aged under simulated natural environmental conditions

Biochar (BC), with the benefits of enhancing soil fertility, absorbing heavy metals, carbon sequestration, and mitigating the greenhouse effect, has been extensively used for soil remediation. However, the long-term changes in the biotoxicity of BC under complex environmental conditions, which are the key factors influencing the sustainable application of BC in soil, are still unclear. Herein, the biotoxicity of BC aged with various processes, including dry‒wet cycle (DW) aging, freeze‒thaw cycle (FT) aging, ultraviolet irradiation (UV) aging, and low molecular weight organic acid (OA) aging, was systematically investigated by Escherichia coli (E. coli) culture experiments. The toxicity attenuation rate (%·week-1) was proposed to more concisely and clearly compare the influence of different aging methods on BC toxicity. The results indicated that after 5 weeks of aging, the toxicity attenuation rate during the four aging modes followed the order OA aging > FT aging > UV aging > DW aging. BC was nontoxic after 1 week of OA aging, 4 weeks of FT aging, 7 weeks of UV aging, and 14 weeks of DW aging. Spectroscopic characterizations revealed that humic acids in the dissolved organic matter of BC were the main reason for the biotoxicity. In addition, the attenuation of environmentally persistent free radicals on BC during aging was also an important factor for reducing environmental toxicity. This work provides insight into the detoxification mechanism of the BC aging process under ordinary environmental conditions and guidance for the safe application of BC in soil.

Bioavailability assessment of difenoconazole to earthworms (Eisenia fetida) in soil by oleic acid-embedded cellulose acetate membrane

Passive sampling technology is widely used to evaluate the bioavailability of pollutants. However, relatively few studies have used passive sampling membranes (PSMs) to evaluate the environmental risks of pollutants in soil, particularly pesticides. Here, the bioavailability of difenoconazole to earthworms (Eisenia fetida) was evaluated using an oleic acid-embedded cellulose acetate membrane (OECAM) for the first time. Difenoconazole reached 94 % equilibrium (T94%) within 1 d in OECAM. For soil pore water, the freely dissolved concentration (Cfree) of difenoconazole was determined using OECAM (R2 = 0.969). In the soil system, a strong linear correlation between the difenoconazole concentration in OECAM and earthworms was observed (R2 = 0.913). The bioavailability of difenoconazole was affected by the soil type and biochar content. The higher the content of soil organic matter and biochar, the lower the concentration of difenoconazole in earthworms, OECAM, and soil pore water. The concentrations of difenoconazole in pore water, earthworms, and OECAM decreased by 65.3, 42.0, and 41.6 %, respectively, when 0.5 % biochar was added. Difenoconazole mainly enters OECAM and earthworms through passive diffusion with similar uptake pathways. Therefore, the bioavailability of difenoconazole to earthworms in different soils can be evaluated using the OECAM.

Photocatalytic degradation of chlorpyrifos using Ag nanoparticles-doped g-C3N5 decorated with dendritic CdS

In this work, g-C3N5/CdS dendrite/AgNPs nanocomposite was synthesized using a mixed method consisting of hydrothermal, ultrasonic and chemistry reduction with sodium borohydride. The characterization of the as-prepared nanocomposite was done using infrared spectroscopy, X-ray, scanning electron microscopy, transmission electron microscopy, BET, and DRS methods was performed. The DRS results showed that the g-C3N5/CdS dendrite/AgNPs nanocomposite nanocomposite has a band gap of 1.08 eV. This band gap indicates the good capability of this nanocomposite as a photocatalyst. Accordingly, the photocatalytic degradation of chlorpyrifos (CPS) in was performed in an aqueous solution of the synthesized nanocomposite. The results showed that almost 95.3% of this poison, a concentration of 50 mg L-1 was degraded in the presence of 0.05 g L-1 of nanocomposite at pH = 5 in a 60 min. Hydroxide radicals and holes play a significant role in the photocatalytic process. The reusability of the nanocomposite with excellent performance in the degradation of photocatalytic toxins caused by the reduction in the electron-hole recombination and the high surface area of the nanocomposite are among the unique features of this work.

Approaching a discussion on the detachment of chlorpyrifos in contaminated water using different leaves and peels as bio adsorbents

The emerging contaminant chlorpyrifos, an insecticide, is generally used in agricultural fields to control termites, ants, and mosquitoes for the proper growth of feed and food crops. Chlorpyrifos reaches water sources for multiple reasons, and people who use water from nearby sources is exposed to chlorpyrifos. Due to its overuse in modern agriculture, the level of chlorpyrifos in water has drastically grown. The present study aims to address the problem arising from the utilization of chlorpyrifos-contaminated water. Natural bioadsorbents Bael, Cauliflower, Guava leaves Watermelon, and lemon peel were employed to remove chlorpyrifos from contaminated water under specific conditions of various factors, such as initial adsorbate concentration, dose of bioadsorbent, contact time, pH, and temperature. Maximum removal efficiency of 77% was obtained with lemon peel. The maximum adsorption capacity (qe) was 6.37 mg g^-1. The kinetic experiments revealed that the pseudo second order model (R² = 0.997) provided a better explanation of the mechanism of sorption. The isotherm showed that chlorpyrifos adsorbed in lemon peel in a monolayer and was best suited by the Langmuir model (R² = 0.993). The adsorption process was exothermic and spontaneous, according to thermodynamic data.

How Well Do Our Adsorbents Actually Perform?-The Case of Dimethoate Removal Using Viscose Fiber-Derived Carbons

Growing pollution is making it necessary to find new strategies and materials for the removal of undesired compounds from the environment. Adsorption is still one of the simplest and most efficient routes for the remediation of air, soil, and water. However, the choice of adsorbent for a given application ultimately depends on its performance assessment results. Here, we show that the uptake of and capacity for dimethoate adsorption by different viscose-derived (activated) carbons strongly depend on the adsorbent dose applied in the adsorption measurements. The specific surface areas of the investigated materials varied across a wide range from 264 m² g^-1 to 2833 m² g^-1. For a dimethoate concentration of 5 × 10^-4 mol L^-1 and a high adsorbent dose of 10 mg mL^-1, the adsorption capacities were all below 15 mg g^-1. In the case of high-surface-area activated carbons, the uptakes were almost 100% under identical conditions. However, when the adsorbent dose was reduced to 0.01 mg mL^-1, uptake was significantly reduced, but adsorption capacities as high as 1280 mg g^-1 were obtained. Further, adsorption capacities were linked to adsorbents' physical and chemical properties (specific surface area, pore size distribution, chemical composition), and thermodynamic parameters for the adsorption process were evaluated. Based on the Gibbs free energy of the adsorption process, it can be suggested that physisorption was operative for all studied adsorbents. Finally, we suggest that a proper comparison of different adsorbents requires standardization of the protocols used to evaluate pollutant uptakes and adsorption capacities.

Preparation and characterization of activated carbon from agricultural wastes and their ability to remove chlorpyrifos from water

Chlorpyrifos is an organophosphate insecticide linked to neurological dysfunctions, endocrine disturbance, cardiovascular illness, genotoxicity, histopathological abnormalities, immunotoxicity, and oxidative stress. Therefore, the aim of this study was to prepare activated carbon from agricultural waste to adsorb and remove chlorpyrifos from aqueous solutions, as well as to study the physicochemical characteristics of the prepared activated carbon.Activated carbon was prepared from agricultural waste (banana peels, orange peels, pomegranate peels and date stones). The activated carbon prepared showed an exterior surface that was irregular and full of cavities with Brunauer-Emmett-Teller(BET) surface areas of 94.26, 111.75, 183.89, and 289.86 m²/g for activated carbon prepared from orange peels, date stone, pomegranate peels, and banana peels respectively. The Scanning Electron Microscope (SEM) image revealed that the activated carbon's exterior surface was irregular and full of various shapes and sizes of cavities.The Energy Dispersive X-Ray (EDX) indicated the existence of carbon, oxygen, silicon and potassium in banana peels-derived activated carbon, whereas carbon, oxygen, silicon and potassium, in addition to aluminium, were detected in the pomegranate peels-derived activated carbon. The Fourier-Transform Infrared Spectroscopy (FTIR) analysis of prepared activated carbon revealed several functional groups, including carboxylic acid, carbon dioxide, and aromatic compounds. Results also showed that the activated carbon significantly removed chlorpyrifos from water, recording 97.6%, 90.6%, 71.48%, and 52.00 % for activated carbon prepared from pomegranate peels, banana peels, date stones and orange peels, respectively. The study concluded that agricultural waste-derived activated carbon could be employed as an alternative pesticide adsorbent.

Heterogeneous photocatalytic oxidation for the removal of organophosphorus pollutants from aqueous solutions: A review

Organophosphorus pollutants (OPs), which are compounds containing carbon‑phosphorus bonds or phosphate derivatives containing organic groups, have received much attention from researchers because of their persistence in the aqueous environment for long periods of time and the threat they pose to human health. Heterogeneous photocatalysis has been widely applied to the removal of OPs from aqueous solutions due to its better removal effect and environmental friendliness. In this review, the removal of OPs from aqueous matrices by heterogeneous photocatalysis was presented. Herein, the application and the heterogeneous photocatalysis mechanism of OPs were described in detail, and the effects of catalyst types on degradation effect are discussed categorically. In particular, the heterojunction type photocatalyst has the most excellent effect. After that, the photocatalytic degradation pathways of several OPs were summarized, focusing on the organophosphorus pesticides and organophosphorus flame retardants, such as methyl parathion, dichlorvos, dimethoate and chlorpyrifos. The toxicity changes during degradation were evaluated, indicating that the photocatalytic process could effectively reduce the toxicity of OPs. Additionally, the effects of common water matrices on heterogeneous photocatalytic degradation of OPs were also presented. Finally, the challenges and perspectives of heterogeneous photocatalysis removal of OPs are summarized and presented.

The Simultaneous Determination of Chlorpyrifos-Ethyl and -Methyl with a New Format of Fluorescence-Based Immunochromatographic Assay

The improper and excessive use in agriculture of chlorpyrifos-methyl (CPSM) and chlorpyrifos-ethyl (CPSE) may affect the health of human beings. Herein, a fluorescence-based immunochromatographic assay (FICA) was developed for the simultaneous determination of CPSM and CPSE. A monoclonal antibody (mAb) with equal recognition of CPSM and CPSE was generated by the careful designing of haptens and screening of hybridoma cells. Instead of labeling fluorescence with mAb, the probe was labeled with goat-anti-mouse IgG (GAM-IgG) and pre-incubated with mAb in the sample. The complex could compete with CPS by coating antigen in the test line. The new format of FICA used goat-anti-rabbit IgG (GAR-IgG) conjugated with rabbit IgG labeled with fluorescence microspheres as an independent quality control line (C line). The novel strategy significantly reduced nonspecific reactions and increased assay sensitivity. Under the optimal conditions, the proposed FICA showed a linear range of 0.015-64 mg/L and limit of detection (LOD) of 0.015 mg/L for both CPSE and CPSM. The average recoveries of CPS from spiked food samples by FICA were 82.0-110.0%. The accuracy was similar to the gas chromatography-tandem mass spectrometry (GC-MS/MS) results. The developed FICA was an ideal on-site tool for rapid screening of CPS residues in foods.

Characterization of organophosphate pesticide sorption of potato peel biochar as low cost adsorbent for chlorpyrifos removal

There has been a growing interest in the scientific world in the production of biochar from natural organic wastes as potential sustainable precursors for bioremediation. Potato peel biochar was produced by slow pyrolysis method under oxygen-limited conditions and used as bio adsorbent in bioremediation of commercial pesticide having Chlorpyrifos as an active component. Chlorpyrifos is an organophosphate pesticide, highly neurotoxic, and primarily targets the central nervous system of pests and insects. The excess residues of chlorpyrifos are hazardous to environmental flora and fauna. Chlorpyrifos was treated against biochar at varying physical parameters and further optimized by using response surface methodology through Box-Behnken design (BBD). 72.06% of pesticide removal was observed post 24 h of treatment against a pesticide concentration of 1346.85 μg/ml with a biochar concentration of 1.04 mg/ml under room temperature at pH 5.04. Biochar was characterized by proximate and ultimate analysis, FTIR, and SEM-EDX. Characterization by SEM-EDX showed the surface morphology and minerals on the peel and biochar. Microgram of potato peel shows pores of larger size than biochar having many cavities with different dimensions. In the plant system, growth morphology, nutritional status, polyphenols, total antioxidant content, and free radical scavenging activity were assessed. Enhancement in presence of biochar was recorded in growth morphology and plant biomolecules including photosynthetic pigments. Better translocation of the nutrient is recorded in biochar treated plants, as evidenced by the low amount of carbohydrate and protein in treated leaves. Biocompatibility assessment of chlorpyriphos in fish erythrocytes showed 43.26% hemolysis by pesticide-treated biochar. The practical use of this approach can also be best utilized if applied to those geographical regions where the soil pH is acidic. Biochar is a marketable bio-product, which can have a positive impact in agriculture, industries, and the energy sector creating a bio-based economy with reduced environmental pollution.

Two-step pyrolysis biochar derived from agro-waste for antibiotics removal: Mechanisms and stability

This study used acetone washing biochar (BCA) and nitric-acid washing biochar (BCN) derived from bagasse to remove sulfamethoxazole (SMX) and tetracycline (TC) in water. Higher specific surface area (1119.53 m² g^-1) and graphitization degree can significantly improve decontamination efficacy, of which BCN has the highest SMX and TC sorption capacities (274.63 mg g^-1 and 353.85 mg g^-1). The kinetics, isotherms and characterization analysis indicated O-containing functional group complexation and π-π interaction were dominant mechanisms in the adsorption process. Adsorption stability experiment showed that BCA has better stability with the coexistence of anions and cations. Besides, the enhancement and competitive adsorption from the interaction between soluble organic matter and TC could facilitate TC decontamination. Therefore, bagasse biochar derived from agro-waste has a promising potential for antibiotic contaminants removal from multi-interference conditions and promotes the recycling of waste, thereby achieving harmony between materials and the ecological environment.

Properties and the Application of Sludge-Based Biochar in the Removal of Phosphate and Methylene Blue from Water: Effects of Acid Treating

Sludge-based biochar could be used to remove phosphate and methylene blue (MB) from water. It is a highly efficient way to treat the sludge and contaminated water synergistically. The high ash content in sludge greatly influenced the adsorption property of the resultant biochar. In this work, the influence of carbonization-activation and acid treating on the adsorption performance of the sludge-based biochar was evaluated. The composition, structure, and surface properties of biochar were improved after acid treating. The biochar was obtained in a sequence of carbonization-activation first and then acid treating, providing the optimal adsorption property. Zn550-H and Zn750-H showed excellent adsorption capacity to phosphate and MB, respectively. The adsorption process was well described by the pseudo-first-order and pseudo-second-order kinetic models. Isothermal studies implied that it was controlled by multiple processes. What is more, sludge-based biochar performed well in the adsorption of phosphate and MB from weakly acidic to alkaline conditions, which was beneficial to utilize the sludge-based biochar in water remediation practically.

Novel insights into the adsorption of organic contaminants by biochar: A review

With rising concerns in the practical application of biochar for the remediation of environment influenced by various organic contaminants, a critical review to facilitate insights the crucial role that biochar has played in wastewater and polluted soil decontamination is urgently needed. This research therefore aimed to describe different intriguing dimensions of biochar interactions with organic contaminants, which including: (i) an introduction of biochar preparation and the related physicochemical properties, (ii) an overview of mechanisms and factors controlling the adsorption of organic contaminants onto biochar, and (iii) a summary of the challenges and an outlook of the further research needs in this issue. In the light of the survey consequences, the appearance of biochar indicates the potential in substituting the existing costly adsorbents, and it has been proved that biochar is one promising adsorbent for organic pollutants adsorption removal from water and soil. However, some research gaps, such as dynamic adsorption, potential environmental risks, interactions between biochar and soil microbes, novel modification techniques, need to be further investigated to facilitate its practical application. This research will be conductive to better understanding the adsorption removal of organic contaminants by biochar.

Biochar from constructed wetland biomass waste: A review of its potential and challenges

Constructed wetland is considered a promising approach for water remediation due to its high efficiency, low operation costs, and ecological benefits, but the large amounts of wetland plant biomass need to be properly harvested and utilized. Recently, wetland plant derived biochar has drawn extensive attention owing to its application potential. This paper provides an updated review on the production and characteristics of wetland plant derived biochar, and its utilization in soil improvement, carbon sequestration, environmental remediation, and energy production. In comparison to hydrothermal carbonization and gasification, pyrolysis is a more common technique to convert wetland plant to biochar. Characteristics of wetland plant biochars varied with plant species, growth environment of plant, and preparation conditions. Wetland plant biochar could be a qualified soil amendment owing to its abundant nutrients. Notably, wetland plant biochar exhibited considerable sorption capacity for various inorganic and organic contaminants. However, the potentially toxic substances (e.g. heavy metal and polycyclic aromatic hydrocarbons) retained in wetland plant biochar should be noticed before large-scale application. To overcome the drawbacks from the scattered distribution, limited productivity, and seasonal operation of constructed wetlands, the economic feasibility of wetland plant biochar production system could be improved via using mobile pyrolysis unit, utilizing local waste heat, and exploiting all the byproducts. Future challenges in the production and application of wetland plant derived biochar include the continuous supply of feedstock and proper handling of potentially hazardous components in the biochar.

Biochar decreased enantioselective uptake of chiral pesticide metalaxyl by lettuce and shifted bacterial community in agricultural soil

A 35-day microcosmic experiment was conducted with lettuce (Lactuca sativa L.) and two metalaxyl (MET) enantiomers (R-MET and S-MET) to understand the roles of biochar in the enantioselective fate of chiral pesticides in soil-plant ecosystems. Wood waste-derived biochar (WBC) amendment effectively decreased the shoot concentrations of R-MET/S-MET and their metabolites R-MET/S-MET acid by 57.7-86.3% and 13.3-32.5%, respectively. The reduced uptake was mainly attributed to the decreased bioavailability of R-MET and S-MET. A lower fraction of R-MET was accumulated by the lettuce in the WBC-amended soils relative to the control, suggesting a decrease in the enantioselective uptake of the chiral pesticide MET in the presence of biochar. Regardless of the WBC amendment, no enantiomerization of MET or MET acid occurred. The application of WBC stimulated soil bacterial diversity, shifted the bacterial community, and enhanced the abundance of pesticide degrading bacteria (e.g., Luteimonas, Methylophilus, and Hydrogenophaga), which were responsible for the enantioselective degradation of MET in the soil. This work expands our understanding of the enantioselective fate of chiral pesticides in the biochar-amended soil ecosystems. These findings can be used to develop biochar-based technologies to remediate soils contaminated with these chiral pesticides to ensure food safety.

Enhancement of photocatalytic degradation of Malachite Green using iron doped titanium dioxide loaded on oil palm empty fruit bunch-derived activated carbon

Iron-doped titanium dioxide loaded on activated carbon (Fe-TiO₂/AC) was successfully synthesized from oil palm empty fruit bunch (OPEFB) using sol-gel method. The properties of the synthesized pure TiO₂, Fe-doped TiO₂, AC, TiO₂/AC and Fe-TiO₂/AC were examined by various techniques such as field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FT-IR), UV-Vis diffuse reflectance spectroscopy (UV-Vis DRS) and nitrogen adsorption-desorption analyses at 77 K. FE-SEM revealed that Fe-doped TiO₂ particles were dispersed homogeneously on the AC surface. FT-IR demonstrated high surface hydroxylation after Fe doping on TiO₂ and UV-Vis DRS showed that Fe-TiO₂/AC had the lowest band gap energy. Catalytic performance results proved that Fe dopants could restrict the recombination rate of hole and electron pairs, whereas AC support improved the Malachite Green (MG) adsorption sites and active sites of the hybrid catalyst. Photocatalytic degradation of 100 mg/L MG in the presence of 1.0 g/L 15 wt% Fe-TiO₂ incorporated with 25 wt% AC, initial solution pH of 4 and 3 mM H₂O₂ could achieve the highest removal efficiency of 97% after 45 min light irradiation. This work demonstrates a promising approach to synthesis an inexpensive and efficient Fe-TiO₂/AC for the photocatalytic degradation of organic dye.

Biochar Aging: Mechanisms, Physicochemical Changes, Assessment, And Implications for Field Applications

Biochar has triggered a black gold rush in environmental studies as a carbon-rich material with well-developed porous structure and tunable functionality. While much attention has been placed on its apparent ability to store carbon in the ground, immobilize soil pollutants, and improve soil fertility, its temporally evolving in situ performance in these roles must not be overlooked. After field application, various environmental factors, such as temperature variations, precipitation events and microbial activities, can lead to its fragmentation, dissolution, and oxidation, thus causing drastic changes to the physicochemical properties. Direct monitoring of biochar-amended soils can provide good evidence of its temporal evolution, but this requires long-term field trials. Various artificial aging methods, such as chemical oxidation, wet-dry cycling and mineral modification, have therefore been designed to mimic natural aging mechanisms. Here we evaluate the science of biochar aging, critically summarize aging-induced changes to biochar properties, and offer a state-of-the-art for artificial aging simulation approaches. In addition, the implications of biochar aging are also considered regarding its potential development and deployment as a soil amendment. We suggest that for improved simulation and prediction, artificial aging methods must shift from qualitative to quantitative approaches. Furthermore, artificial preaging may serve to synthesize engineered biochars for green and sustainable environmental applications.

Arsenite oxidation and arsenic adsorption on birnessite in the absence and the presence of citrate or EDTA

Birnessite not only oxidizes arsenite into arsenate but also interacts with organic matter in various ways. However, effects of organic matter on interaction between As and birnessite remain unclear. This study investigated effects of citrate and EDTA (3.12 and 2.05 mM, respectively) on oxidation of As(III) (1.07 mM) and adsorption of As(V) (0.67 mM) on birnessite (5.19 mM as Mn) at near-neutral pH. We found that As(V) adsorption on birnessite was enhanced by citrate and EDTA, which resulted from the increase in active adsorption sites via dissolution of birnessite. In comparison with citrate batches, more As was adsorbed on birnessite in EDTA batches, where dissolved Mn was mainly presented as Mn(III)-EDTA complex. Citrate or EDTA-induced dissolution of birnessite did not decrease the As(III) oxidation rate in the initial stage where As(III) oxidation rate was rapid. Afterwards, As(III) oxidation was conspicuously suppressed in citrate-amended batches, which was mainly attributed to the decrease in adsorption sites by adsorption of citrate/Mn(II)-citrate complex. This suppression was enhanced by the increase in concentrations of dissolved Mn(II). Citrate inhibited As adsorption after As(III) oxidation due to the strong competitive adsorption of citrate/Mn(II)-citrate complex. However, the As(III) oxidation rate was increased in EDTA-amended batches in the late stage, which mainly derived from the increase in the active sites via birnessite dissolution. The strong complexation ability of EDTA led to formation of Mn(III)-EDTA complex. Arsenic adsorption was not affected due to the limited competitive adsorption of the complex on the solid. This work reveals the critical role of low molecular weight organic acids in geochemical behaviors of As and Mn in aqueous environment.

Biochar reduced Chinese chive (Allium tuberosum) uptake and dissipation of thiamethoxam in an agricultural soil

Information about the effect of biochar on the environmental fate of pesticide thiamethoxam (THI) in soil-vegetable ecosystems is limited. Therefore, the influence of a wood-derived biochar produced at 450 °C (BC450) on the uptake of THI by Chinese chive (Allium tuberosum) and its dissipation in soil was investigated using a 42-day pot experiment. BC450 addition decreased THI uptake and its metabolite clothianidin (CLO) by 22.8 % and 37.6 %, respectively. However, the half-life of THI in soil rose from 89.4-120 days, indicating that BC450 increased soil THI's persistence. The decreased bioavailability and increased persistence of THI resulted mainly from the higher sorption capacity of BC450 to THI and CLO, which, in turn, enhanced the soil sorption capacity. Consequently, the application of BC450 increased the soil microbial diversity and altered the structure of the microbial community. Although the abundance of Actinobacteria associated with the biodegradation of THI, increased the persistence of THI in the BC450-amended soil, mainly due to the decrease in bioavailable THI. Our findings provide valuable information about the effect of biochar on the fate of THI and its metabolites in agricultural soil and will help to guide the practical application of biochar to remediate soils contaminated with neonicotinoid pesticides.

Physicochemical properties and sorption capacities of sawdust-based biochars and commercial activated carbons towards ethoxylated alkylphenols and their phenolic metabolites in effluent wastewater from a textile district

Three biochars were produced using sawdust from waste biomass, via a simple pyrolysis thermal conversion at 450, 650, and 850 °C (BC450, BC650, and BC850), without any activation process. These materials, together with vegetal and mineral commercial activated carbons (VAC and MAC), were characterized for their elemental composition, Brunauer-Emmett-Teller surface area, t-plot microporosity and Barrett-Joyner-Halenda mesoporosity. Moreover, iodine, phenol and methylene blue porosity indexes were measured. The materials were also evaluated for their pH of the point of zero charge, as well as near-surface chemical composition and surface functionality by means of X-ray photoelectron and Fourier-transform infrared spectroscopy. Ash content, water-extractable metals and polycyclic aromatic hydrocarbons (PAHs) were also determined. BC650 showed a much higher surface area (319 m² g^-1) compared to BC450 (102 m² g^-1), as well as an increase in aromatization and the residual presence of functional polar groups. BC850 exhibited a loss of polar and aromatic groups, with the dominance of graphitic carbon and the highest value of surface area (419 m² g^-1). Biochars comply with the EN 12915-1/2009 limits for metal and PAH release in water treatment. Biochars and MAC were tested using Langmuir and Freundlich isotherms for the sorption in real effluent wastewater of a mixture of 14 branched ethoxylated 4-t-octyl and 4-nonylphenols, as well as 4-t-octyl and 4-nonylphenol, the latter representing persistent, endocrine disrupting contaminants, widespread in the effluents from wastewater treatment plants and listed as priority/priority hazardous substances in the Directive 2013/39/EU. Biochars showed a lower sorption efficiency compared to MAC. The best performance was found for BC650 towards the alkylphenols (9-13 times less efficient than the MAC). Considering the lower market price of biochar compared to MAC (estimated as at least 16 times less expensive by a small market survey), the former can be considered more competitive than the latter.

Preparation and evaluation of hydrocalumite-iron oxide magnetic intercalated with dodecyl sulfate for removal of agrichemicals

The magnetic adsorbent prepared with hydrocalumite-iron oxide (HC/Fe) modified with dodecyl sulfate (DS) was examined for the removal of the agrichemicals atrazine (ATZ) and chlorpyrifos (CPF) from aqueous solution. The adsorbent HC-DS/Fe was characterized by infrared spectroscopy (IR), Raman spectroscopy, X-ray diffractometry (XRD) and atomic absorption spectrometry. The effects of adsorbent dosage, contact time, pH and initial concentration of ATZ and CPF were evaluated. HC-DS/Fe presented a maximum adsorption capacity for ATZ of 4.5 mg g^-1 (30 min) and for CPF of 72.9 mg g^-1 (210 min) at 25 °C. HC-DS/Fe can be readily removed from the aqueous solution by magnetization because of its magnetic properties. The free energy variation for HC-DS/Fe during the adsorption of the ATZ was -48.78 to -53.91 kJ mol^-1 and for the CPF of -55.79 to -59.28 kJ mol^-1, suggesting the spontaneity of the adsorption process. The positive value of △H suggests an endothermic process for the interaction of ATZ and CPF by HC-DS/Fe. This adsorbent showed satisfactory results when used in the treatment of a sample of river water, fortified with the agrichemicals chlorpyrifos, atrazine, thiamethoxam and acetamiprid.

Photocatalytic degradation of an organophosphorus pesticide using a ZnO/rGO composite

A zinc oxide (ZnO)/reduced graphene oxide (rGO) nanocomposite was synthesized via a hydrothermal synthesis method and used for the photocatalytic degradation of dimethoate. In the synthesis process of the ZnO/rGO nanocomposite, hexamethylenetetramine (HMT) was used as both a mineralizer and reducing agent. When the ZnO nanoparticles formed on the surfaces of graphene oxide sheets, the sheets were simultaneously reduced by HMT to form rGO. The photodegradation rate and photodegradation efficiency of dimethoate by the ZnO/rGO nanocomposite were 4 and 1.5 times, respectively, higher than those of bare ZnO. The ZnO/rGO nanocomposite possessed a high surface area of 41.0 m² g⁻¹ and pore volume of 4.72 × 10⁻³ cm³ g⁻¹, which were conducive to the adsorption and mass transfer of pesticides and oxygen. The enhanced photocatalytic performance of the ZnO/rGO nanocomposite was attributed to the decrease in electron–hole recombination rate and effective carrier transport caused by the presence of rGO. Photoelectrochemical measurements confirmed that the nanocomposite exhibited a high charge transfer rate at the ZnO/rGO interface. These results indicate that ZnO/rGO nanocomposites have great application potential in pollutant degradation.

The fabricated ZnO/rGO nanocomposites performed enhanced photocatalytic performance due to a high charge transfer rate at the ZnO/rGO interface.

Rapid removal of triazine pesticides by P doped biochar and the adsorption mechanism

Biochar is an adsorbent widely used to remove contaminants from polluted water. A series of biochar from corn straw, corncob and corn starch was prepared through one-step pyrolysis. The biochar was characterized, and the capacity for triazine pesticide (TRZ) removal from water was compared. P doped biochar from corn straw (CSWP) was able to remove six TRZs (>96%) from water after shaking five times. The removal was more rapid than that by four other commonly used adsorbents. The physicochemical properties of CSWP were characterized systematically, and carboxyl and metaphosphates on CSWP were found to provide adsorption sites. The experimental data were best fitted by a pseudo-second-order kinetic model and the Freundlich model. Adsorption equilibrium of atrazine on CSWP occurred within 20 min, and the maximum adsorption capacity reached up to 79.6 mg g^-1 at 25 °C. The adsorption mechanism of CSWP for atrazine includes Van der Waals' forces, hydrogen bonding, electrostatic interactions and pore filling. CSWP can be reused at least five times and shows strong potential as a candidate for the rapid and efficient removal of TRZs.