Bio-electrochemical power generation in petrochemical wastewater fed microbial fuel cell

Electricity generation and real oily wastewater treatment by Pseudomonas citronellolis 620C in a microbial fuel cell: pyocyanin production as electron shuttle

In the present study, the potential of Pseudomonas citronellolis 620C strain was evaluated, for the first time, to generate electricity in a standard, double chamber microbial fuel cell (MFC), with oily wastewater (OW) being the fuel at 43.625 mg/L initial chemical oxygen demand (COD). Both electrochemical and physicochemical results suggested that this P. citronellolis strain utilized efficiently the OW substrate and generated electricity in the MFC setup reaching 0.05 mW/m2 maximum power. COD removal was remarkable reaching 83.6 ± 0.1%, while qualitative and quantitative gas chromatography/mass spectrometry (GC/MS) analysis of the OW total petroleum and polycyclic aromatic hydrocarbons, and fatty acids revealed high degradation capacity. It was also determined that P. citronellolis 620C produced pyocyanin as electron shuttle in the anodic MFC chamber. To the authors' best knowledge, this is the first study showing (phenazine-based) pyocyanin production from a species other than P. aeruginosa and, also, the first time that P. citronellolis 620C has been shown to produce electricity in a MFC. The production of pyocyanin, in combination with the formation of biofilm in the MFC anode, as observed with scanning electron microscopy (SEM) analysis, makes this P. citronellolis strain an attractive and promising candidate for wider MFC applications.

Biodegradation of petroleum wastewater for the production of bioelectricity using activated sludge biomass

Objective

This research is based on the treatment of petroleum wastewater (PWW) with pretreated activated sludge for the production of electricity and removal of chemical oxygen demand (COD) using microbial fuel cell (MFC).

Methods

The application of the MFC system which uses activated sludge biomass (ASB) as a substrate resulted in the reduction of COD by 89.5% of the original value. It generated electricity equivalent to 8.18 mA/m2 which can be reused again. This would solve the majority of environmental crises which we are facing today.

Results

This study discusses the application of ASB to enhance the degradation of PWW for the production of a power density of 1012.95 mW/m2 when a voltage of 0.75 V (voltage) is applied at 30:70% of ASB when MFC is operated in a continuous mode. Microbial biomass growth was catalyzed using activated sludge biomass. The growth of microbes was observed by scanning through an electron microscope. Through oxidation in the MFC system, bioelectricity is generated which is used in the cathode chamber. Furthermore, the MFC operated using ASB in a ratio of 35 with the current density, which decreased to 494.76 mW/m2 at 10% ASB.

Application

Our experiments demonstrate that the efficiency of the MFC system can generate bioelectricity and treat petroleum wastewater by using activated sludge biomass.

Putting the electro-bugs to work: A systematic review of 22 years of advances in bio-electrochemical systems and the parameters governing their performance

Wastewater treatment using bioelectrochemical systems (BESs) can be considered as a technology finding application in versatile areas such as for renewable energy production and simultaneous reducing environmental problems, biosensors, and bioelectrosynthesis. This review paper reports and critically discusses the challenges, and advances in bio-electrochemical studies in the 21st century. To sum and critically analyze the strides of the last 20+ years on the topic, this study first provides a comprehensive analysis on the structure, performance, and application of BESs, which include Microbial Fuel Cells (MFCs), Microbial Electrolysis Cells (MECs) and Microbial Desalination Cells (MDCs). We focus on the effect of various parameters, such as electroactive microbial community structure, electrode material, configuration of bioreactors, anode unit volume, membrane type, initial COD, co-substrates and the nature of the input wastewater in treatment process and the amount of energy and fuel production, with the purpose of showcasing the modes of operation as a guide for future studies. The results of this review show that the BES have great potential in reducing environmental pollution, purifying saltwater, and producing energy and fuel. At a larger scale, it aspires to facilitate the path of achieving sustainable development and practical application of BES in real-world scenarios.

New microbial electrosynthesis system for methane production from carbon dioxide coupled with oxidation of sulfide to sulfate

Microbial electrosynthesis system (MES) is a promising method that can use carbon dioxide, which is a greenhouse gas, to produce methane which acts as an energy source, without using organic substances. However, this bioelectrical reduction reaction can proceed at a certain high applied voltage when coupled with water oxidation in the anode coated with metallic catalyst. When coupled with the oxidation of HS^- to SO₄^2-, methane production is thermodynamically more feasible, thus implying its production at a considerably lower applied voltage. In this study, we demonstrated the possibility of electrotrophic methane production coupled with HS^- oxidation in a cost-effective bioanode chamber in the MES without organic substrates at a low applied voltage of 0.2 V. In addition, microbial community analyses of biomass enriched in the bioanode and biocathode were used to reveal the most probable pathway for methane production from HS^- oxidation. In the bioanode, electroautotrophic SO₄^2- production accompanied with electron donation to the electrode is performed mainly by the following two steps: first, incomplete sulfide oxidation to sulfur cycle intermediates (SCI) is performed; then the produced SCI are disproportionated to HS^- and SO₄^2-. In the biocathode, methane is produced mainly via H₂ and acetate by electron-accepting syntrophic bacteria, homoacetogens, and acetoclastic archaea. Here, a new eco-friendly MES with biological H₂S removal is established.

Engineering Shewanella oneidensis to efficiently harvest electricity power by co-utilizing glucose and lactate in thin stillage of liquor industry

Thin stillage, rich in glucose and lactate, can seriously pollute water resources when directly discharged into the natural environment. Microbial fuel cells (MFC), as a green and sustainable technology, could utilize exoelectrogens to break down organics in wastewater and harvest electricity. Nevertheless, Shewanella oneidensis MR-1, cannot utilize thin stillage for efficient power generation. Here, to enable S. oneidensis to co-utilize glucose and lactate from thin stillage, an engineered S. oneidensis G₇∆RSL₁ was first created by constructing glucose metabolism pathway, promoting glucose and lactate co-utilization, and enhancing biofilm formation. Then, to enhance biofilm conductivity, we constructed a 3D self-assembled G₇∆RSL₁-rGO/CNT biohybrid with maximum power density of 560.4 mW m^-2 and 373.7 mW m^-2 in artificial and actual thin stillage, respectively, the highest among the reported genetically engineered S. oneidensis with thin stillage as carbon source. This study provides a new strategy to facilitate practical applications of MFC in wastewater remediation and efficient power recovery.

Gd-Co nanosheet arrays coated on N-doped carbon spheres as cathode catalyst in photosynthetic microalgae microbial fuel cells

Biocompatible, durable and high catalytic cathode is crucial for the performance of photosynthetic microalgae microbial fuel cell (PMMFC). In this study, gadolinium-cobalt (Gd-Co) nanosheet arrays were coated on N-doped carbon spheres (N-CSs) that were supported using nickel foam (NF), to form a unique 3D hierarchical architecture of Gd-Co@N-CSs/NF cathode material. The morphology and structure of Gd-Co@N-CSs/NF was investigated by physicochemical characterization. The electricity generation and stability of NF, N-CSs/NF, Co@N-CSs/NF and Gd-Co@N-CSs/NF were evaluated using a dual-chamber PMMFC system with Chlorella vulgaris (C. vulgaris) in the cathode chamber. Results showed that doption of Gd to the cathode material resulted in Gd-Co@N-CSs/NF exhibiting superior catalytic activity for the oxygen reduction reaction (ORR), with an ORR peak potential of 0.78 V (vs. RHE). The electron transfer number (n) of Gd-Co@N-CSs/NF was 3.906, indicating ORR was mainly realized via 4e^- transfer pathway. Gd-Co@N-CSs/NF achieved a maximum power density of 115.9 mW m^-2 and an open circuit voltage of 614.8 mV, higher than the other three cathode materials. Gd-Co@N-CSs/NF exhibited excellent stability during 360 h of the PMMFC process, only dropping 5.8 % of maximum voltage. The cell density of C. vulgaris (3.7 × 10¹⁰ cells L^-1) in Gd-Co@N-CSs/NF system was significantly higher than those of NF, N-CSs/NF and Co@N-CSs/NF. This study shows that Gd-Co@N-CSs/NF is a promising cathode material and may be highly beneficial for the enhancement of PMMFC systems.

Biological methane production coupled with sulfur oxidation in a microbial electrosynthesis system without organic substrates

Methane is produced in a microbial electrosynthesis system (MES) without organic substrates. However, a relatively high applied voltage is required for the bioelectrical reactions. In this study, we demonstrated that electrotrophic methane production at the biocathode was achieved even at a very low voltage of 0.1 V in an MES, in which abiotic HS^- oxidized to SO₄^2- at the anodic carbon-cloth surface coated with platinum powder. In addition, microbial community analysis revealed the most probable pathway for methane production from electrons. First, electrotrophic H₂ was produced by syntrophic bacteria, such as Syntrophorhabdus, Syntrophobacter, Syntrophus, Leptolinea, and Aminicenantales, with the direct acceptance of electrons at the biocathode. Subsequently, most of the produced H₂ was converted to acetate by homoacetogens, such as Clostridium and Spirochaeta 2. In conclusion, the majority of the methane was indirectly produced by a large population of acetoclastic methanogens, namely Methanosaeta, via acetate. Further, hydrogenotrophic methanogens, including Methanobacterium and Methanolinea, produced methane via H₂.

Augmentation of microbial fuel cell and photocatalytic polishing technique for the treatment of hazardous dimethyl phthalate containing wastewater

In the present paper, the potentiality of integrating microbial fuel cells (MFCs) with a photocatalytic reactor to maximize the wastewater treatment efficiency with concurrent power generation was explored. Dimethyl phthalate (DMP) and acetic acid (AA) were the employed substrate and the co-substrate, respectively, using Pseudomonas aeruginosa as a biocatalyst. MFCs operated by single substrate showed the maximum power generation of 0.75-3.84 W m^-3 whereas an addition of AA as the co-substrate yielded 3-12 fold higher power generation. Pseudomonas aeruginosa produced phenazine-1-carboxylic acid in DMP-fed MFC as the metabolite whereas AA along with DMP yielded pyocyanin which reduced the charge transfer resistance. Chemical oxygen demand (COD) removal efficiency in the MFCs was circa 62% after 11 days of operation. Thereafter, it further increased albeit with a drastic reduction in power generation. Subsequently, the MFC anolyte was treated in a photocatalytic reactor under visible light irradiation and catalyzed by CuO-gC₃N₄. The performance of photocatalytic reactor was evaluated, with COD and total organic carbon (TOC) removal efficiency of 88% and 86% after 200 min of light irradiation. The present work suggests that the MFC can be integrated with photocatalysis as a sustainable wastewater treatment method with concurrent power generation.

Applications of Biocatalysts for Sustainable Oxidation of Phenolic Pollutants: A Review

Phenol and its derivatives are hazardous, teratogenic and mutagenic, and have gained significant attention in recent years due to their high toxicity even at low concentrations. Phenolic compounds appear in petroleum refinery wastewater from several sources, such as the neutralized spent caustic waste streams, the tank water drain, the desalter effluent and the production unit. Therefore, effective treatments of such wastewaters are crucial. Conventional techniques used to treat these wastewaters pose several drawbacks, such as incomplete or low efficient removal of phenols. Recently, biocatalysts have attracted much attention for the sustainable and effective removal of toxic chemicals like phenols from wastewaters. The advantages of biocatalytic processes over the conventional treatment methods are their ability to operate over a wide range of operating conditions, low consumption of oxidants, simpler process control, and no delays or shock loading effects associated with the start-up/shutdown of the plant. Among different biocatalysts, oxidoreductases (i.e., tyrosinase, laccase and horseradish peroxidase) are known as green catalysts with massive potentialities to sustainably tackle phenolic contaminants of high concerns. Such enzymes mainly catalyze the o-hydroxylation of a broad spectrum of environmentally related contaminants into their corresponding o-diphenols. This review covers the latest advancement regarding the exploitation of these enzymes for sustainable oxidation of phenolic compounds in wastewater, and suggests a way forward.

Application of microbial electrochemical technologies for the treatment of petrochemical wastewater with concomitant valuable recovery: A review

Petrochemical industry is one of the major and rapidly growing industry that generates a variety of toxic and recalcitrant organic pollutants as by-products, which are not only harmful to the aquatic animals but also affects human health. The majority of the components of petrochemical wastewater (PW) are carcinogenic, genotoxic and phytotoxic in nature; hence, this complex wastewater generated from different petrochemical processes should be efficiently treated prior to its disposal in natural water bodies. The established technologies like advanced oxidation, membrane bioreactor, electrocoagulation and activated sludge process employed for the treatment of PW are highly energy intensive and incurs high capital and operation cost. Moreover, these technologies are not effective in completely eliminating petroleum hydrocarbons present in PW. Thus, to reduce the energy requirement and also to transform the chemical energy trapped in these organic matters present in this wastewater into bioelectricity and other value-added products, microbial electrochemical technologies (METs) can be efficaciously used, which would also compensate the treatment cost by transforming these pollutants into bioenergy and valuables. In this regard, this review elucidates the feasibility and application of different METs as an appropriate alternative for the treatment of PW. Furthermore, the numerous bottlenecks towards the real-life application and commercialization of pioneering METs have also been articulated.

Advanced microbial fuel cell for waste water treatment-a review

Petroleum, coal, and natural gas reservoir were depleting continuously due to an increase in industrialization, which enforced study to identify alternative sources. The next option is the renewable resources which are most important for energy purpose coupled with environmental problem reduction. Microbial fuel cells (MFCs) have become a promising approach to generate cleaner and more sustainable electrical energy. The involvement of various disciplines had been contributing to enhancing the performance of the MFCs. This review covers the performance of MFC along with different wastewater as a substrate in terms of treatment efficiencies as well as for energy generation. Apart from this, effect of various parameters and use of different nanomaterials for performance of MFC were also studied. From the current study, it proves that the use of microbial fuel cell along with the use of nanomaterials could be the waste and energy-related problem-solving approach. MFC could be better in performances based on optimized process parameters for handling any wastewater from industrial process.

Bioelectrical Methane Production with an Ammonium Oxidative Reaction under the No Organic Substance Condition

The present study investigated bioelectrical methane production from CO₂ without organic substances. Even though microbial methane production has been reported at relatively high electric voltages, the amount of voltage required and the organisms contributing to the process currently remain unknown. Methane production using a biocathode was investigated in a microbial electrolysis cell coupled with an NH₄⁺ oxidative reaction at an anode coated with platinum powder under a wide range of applied voltages and anaerobic conditions. A microbial community analysis revealed that methane production simultaneously occurred with biological denitrification at the biocathode. During denitrification, NO₃^– was produced by chemical NH₄⁺ oxidation at the anode and was provided to the biocathode chamber. H₂ was produced at the biocathode by the hydrogen-producing bacteria Petrimonas through the acceptance of electrons and protons. The H₂ produced was biologically consumed by hydrogenotrophic methanogens of Methanobacterium and Methanobrevibacter with CO₂ uptake and by hydrogenotrophic denitrifiers of Azonexus. This microbial community suggests that methane is indirectly produced without the use of electrons by methanogens. Furthermore, bioelectrical methane production occurred under experimental conditions even at a very low voltage of 0.05‍ ‍V coupled with NH₄⁺ oxidation, which was thermodynamically feasible.

A review on treatment of petroleum refinery and petrochemical plant wastewater: A special emphasis on constructed wetlands

Petroleum refinery and petrochemical plants (PRPP) are one of the major contributors to toxic and recalcitrant organic polluted water, which has become a significant concern in the field of environmental engineering. Several contaminants of PRPP wastewater are genotoxic, phytotoxic, and carcinogenic, thereby imposing detrimental effects on the environment. Many biological processes were able to achieve chemical oxygen demand (COD) removal ranging from 60% to 90%, and their retention time usually ranged from 10 to 100 days. These methods were not efficient in removing the petroleum hydrocarbons present in PRPP wastewater and produced a significant amount of oily sludge. Advanced oxidation processes achieved the same COD removal efficiency in a few hours and were able to break down recalcitrant organic compounds. However, the associated high cost is a significant drawback concerning PRPP wastewater treatment. In this context, constructed wetlands (CWs) could effectively remove the recalcitrant organic fraction of the wastewater because of the various inherent mechanisms involved, such as phytodegradation, rhizofiltration, microbial degradation, sorption, etc. In this review, we found that CWs were efficient in handling large quantities of high strength PRPP wastewater exhibiting average COD removal of around 80%. Horizontal subsurface flow CWs exhibited better performance than the free surface and floating CWs. These systems could also effectively remove heavy oil and recalcitrant organic compounds, with an average removal efficiency exceeding 80% and 90%, respectively. Furthermore, modifications by varying the aeration system, purposeful hybridization, and identifying the suitable substrate led to the enhanced performance of the systems.

Petrochemical wastewater and produced water: Treatment technology and resource recovery

Petrochemical wastewater and produced water from oil and gas operations typically contain an array of organic and inorganic contaminants. The complexity of the wastewater, stringent environmental regulations, and the need for sustainable solutions have driven many research efforts in studying and developing advanced technology or combined treatment processes. On the other hand, the wastewater itself can be resources for water, energy, and other valuable product if appropriate technology is developed to recover them in a cost-effective fashion. The research advances in wastewater treatment and resource recovery technology are reviewed and summarized. For petrochemical wastewater, progresses were made in advanced oxidation, biological processes, and recovery of energy and water from wastewater. For produced water, many efforts were focused on membrane processes, combined systems, and biological treatment. PRACTITIONER POINTS: Significant progress continued to be made on petrochemical wastewater and produced water treatment. Recent technological advances in various treatment processes were summarized. Technologies focusing on resource recovery (e.g., water or energy) were presented.

Chemical waste and allied products

This paper reviews the related literature reported in 2019 about various types of wastewaters associated with chemical and allied products. The subjects comprise wastewaters produced from various activities in agricultural, chemical, dye, petrochemical, and pharmaceutical. PRACTITIONER POINTS: Bioflocculant chitosan was used for sludge dewatering and the treatment of water and wastewater, and polishing of sanitary landfill leachate. Alkaline lignin-based flocculants were used to achieve excellent color removal for paper mill sludge. Powdered activated coke was used to remove COD (chemical oxygen demand) from chemical industry wastewater effluents.

PVDF-Modified Nafion Membrane for Improved Performance of MFC

Low power production and unstable power supply are important bottlenecks restricting the application of microbial fuel cells (MFCs). It is necessary to explore effective methods to improve MFC performance. By using molasses wastewater as fuel, carbon felt as an electrode, and the mixture of K3[Fe(CN)6] and NaCl as a catholyte, an MFC experimental system was set up to study the performance of MFCs with three different proton exchange membranes. A Nafion membrane was used as the basic material, and polyvinylidene fluoride (PVDF) and acetone-modified PVDF were used to modify it, respectively. The experimental results show that a PVDF-modified membrane can improve the water absorption effectively and, thus, make the MFC have greater power generation and better wastewater treatment effect. The acetone-modified PVDF can further improve the stability of output power of the MFC. When the acetone-modified PVDF was used to modify the Nafion membrane, the steady output voltage of the MFC was above 0.21 V, and the Chemical Oxygen Demand (COD) removal rate for molasses wastewater was about 66.7%, which were 96.3% and 75.1% higher than that of the MFC with the ordinary Nafion membrane. Membrane modification with acetone-modified PVDF can not only increase the output voltage of the MFC but also improve the stability of its output electrical energy.