Preparation of biochar and biochar composites and their application in a Fenton-like process for wastewater decontamination: A review

Synthesis and evaluation of a novel cross-linked biochar/ferric chloride hybrid material for integrated coagulation and adsorption of turbidity and humic acid from synthetic wastewater: Implications for sludge valorisation

The deep removal of organic pollutants is challenging for coagulation technology in drinking water and wastewater treatment plants to satisfy the rising water standards. Iron (III) chloride (FeCl3) is a popular inorganic coagulant; although it has good performance in removing the turbidity (TB) in water at an alkaline medium, it cannot remove dissolved pollutants and natural organic matter such as humic acid water solution. Additionally, its hygroscopic nature complicates determining the optimal dosage for effective coagulation. Biochar (BC), a popular adsorbent with abundant functional groups, porous structure, and relatively high surface area, can adsorb adsorbates from water matrices. Therefore, combining BC with FeCl3 presents a potential solution to address the challenges associated with iron chloride. Consequently, this study focused on preparing and characterizing a novel biochar/ferric chloride-based coagulant (BC-FeCl3) for efficient removal of turbidity (TB) and natural organic matter, specifically humic acid (HA), from synthetic wastewater. The potential solution for the disposal of produced sludge was achieved by its recovering and recycling, then used in adsorption of HA from aqueous solution. The novel coagulant presented high TB and HA removal within 10 min of settling period at pH solution of 7.5. Furthermore, the recovered sludge presented a good performance in the adsorption of HA from aqueous solution. Adsorption isotherm and kinetics studies revealed that the Pseudo-second-order model best described kinetic adsorption, while the Freundlich model dominated the adsorption isotherm.

The molecular binding sequence transformation of soil organic matter and biochar dissolved black carbon antagonizes the transport of 2,4,6-trichlorophenol

Dissolved organic matter (DOM) and dissolved black carbon (DBC) are significant environmental factors that influence the transport of organic pollutants. However, the mechanisms by which their molecular diversity affects pollutant transport remain unclear. This study elucidates the molecular binding sequence and adsorption sites through which DOM/DBC compounds antagonize the transport of 2,4,6-trichlorophenol (TCP) using column experiments and modelling. DBC exhibits a high TCP adsorption rate (kn = 5.32 × 10-22 mol1-n∙Ln-1∙min-1) and conditional stability constant (logK = 5.19-5.74), indicating a strong binding affinity and antagonistic effect on TCP. This is attributed to the high relative content of lipid/protein compounds in DBC (25.65 % and 30.28 %, respectively). Moreover, the small molecule lipid compounds showed stronger TCP adsorption energy (Ead = -0.0071 eV/-0.0093 eV) in DOM/DBC, combined with two-dimensional correlation spectroscopy model found that DOM/DBC antagonized TCP transport in the environment through binding sequences that transformed from lipid/protein small molecule compounds to lignin/tannin compounds. This study used a multifaceted approach to comprehensively assess the impact of DOM/DBC on TCP transport. It reveals that the molecular diversity of DOM/DBC is a critical factor affecting pollutant transport, providing important insights into the environmental trend and ecological effects of pollutants.

High surface area biochar for the removal of naphthenic acids from environmental water and industrial wastewater

This study reports the production of biochar adsorbents from two major crop residues (i.e., rice and wheat straw) to remove naphthenic acids from water. The alkali treatment approach was used for biochar activation that resulted in a tremendous increase in their surface area, i.e., up to 2252 and 2314 m2/g, respectively, for rice and wheat straw biochars. Benzoic acid was used as a model compound to optimize critical adsorption parameters. Its maximum monolayer adsorption capacity of 459.55 and 357.64 mg/g was achieved for activated rice and wheat straw biochars. The adsorption of benzoic acid was exothermic (∆H° =  - 7.06 and - 3.89 kJ/mol) and identified possibly as physisorption (Gibbs free energy ranges 3.5-4.0 kJ/mol). The kinetic study suggested that adsorption follows pseudo-second-order kinetics with qe2 for rice straw and wheat straw-derived adsorbents at 200 and 194 mg/g, respectively. As adsorbent, the recyclability of activated biochars was noticed with no significant loss in their efficiency for up to ten successive regeneration cycles. The adsorption results were validated using a commercial naphthenic acid mixture-spiked river water and paper/pulp industrial effluent. The activated rice and wheat straw biochars exhibited excellent adsorption efficiency of 130.3 and 74.6 mg/g, respectively. The naphthenic acid adsorption on biochar surface was due to various interactions, i.e., weak van der Waal's, pore filling, π-π stacking, and ionic interactions. This study offers a cost-effective and eco-friendly approach to valorizing agricultural residues for pollutant removal from industrial wastewater, including petroleum refineries.

The boom era of emerging contaminants: A review of remediating agricultural soils by biochar

Emerging contaminants (ECs) are widely sourced persistent pollutants that pose a significant threat to the environment and human health. Their footprint spans global ecosystems, making their remediation highly challenging. In recent years, a significant amount of literature has focused on the use of biochar for remediation of heavy metals and organic pollutants in soil and water environments. However, the use of biochar for the remediation of ECs in agricultural soils has not received as much attention, and as a result, there are limited reviews available on this topic. Thus, this review aims to provide an overview of the primary types, sources, and hazards of ECs in farmland, as well as the structure, functions, and preparation types of biochar. Furthermore, this paper emphasizes the importance and prospects of three remediation strategies for ECs in cropland: (i) employing activated, modified, and composite biochar for remediation, which exhibit superior pollutant removal compared to pure biochar; (ii) exploring the potential synergistic efficiency between biochar and compost, enhancing their effectiveness in soil improvement and pollution remediation; (iii) utilizing biochar as a shelter and nutrient source for microorganisms in biochar-mediated microbial remediation, positively impacting soil properties and microbial community structure. Given the increasing global prevalence of ECs, the remediation strategies provided in this paper aim to serve as a valuable reference for future remediation of ECs-contaminated agricultural lands.

Machine learning screening of biomass precursors to prepare biomass carbon for organic wastewater purification: A review

In the past decades, the amount of biomass waste has continuously increased in human living environments, and it has attracted more and more attention. Biomass is regarded as the most high-quality and cost-effective precursor material for the preparation carbon of adsorbents and catalysts. The application of biomass carbon has extensively explored. The efficient application of biomass carbon in organic wastewater purification were reviewed. With briefly introducing biomass types, the latest progress of Machine learning in guiding the preparation and application of biomass carbon was emphasized. The key factors in constructing efficient biomass carbon for adsorption and catalytic applications were discussed. Based on the functional groups, rich pore structure and active site of biomass carbon, it exhibits high efficiency in water purification performance in the fields of adsorption and catalysis. In addition, out of a firm belief in the enormous potential of biomass carbon, the remaining challenges and future research directions were discussed.

Synergistic interactions and reaction mechanisms of biochar surface functionalities in antibiotics removal from industrial wastewater

Biochar, a carbon-rich material with a unique surface chemistry (high abundance of surface functional groups, large surface area, and well-distributed), has shown great potential as a sustainable solution for industrial wastewater treatment as compared to conventional industrial wastewater treatment techniques demand substantial energy consumption and generate detrimental byproducts. This critical review emphasizes the surface functionalities formation and development in biochar to enhance its physiochemical properties, for utilization in antibiotics removal. Factors affecting the formation of functionalities, including carbonization processes, feedstock materials, operating parameters, and the influence of pre-post treatments, are thoroughly highlighted to understand the crucial role of factors influencing biochar properties for optimal antibiotics removal. Furthermore, the research explores the removal mechanisms and interactions of biochar-based surface functionalities, hydrogen bonding, encompassing electrostatic interactions, hydrophobic interactions, π-π interactions, and electron donor and acceptor interactions, to provide insights into the adsorption/removal behavior of antibiotics on biochar surfaces. The review also explains the mechanism of factors influencing the removal of antibiotics in industrial wastewater treatment, including particle size and pore structure, nature and types of surface functional groups, pH and surface charge, temperature, surface modification strategies, hydrophobicity/hydrophilicity, biochar dose, pollutant concentration, contact time, and the presence of coexisting ions and other substances. Finally, the study offers reusability and regeneration, challenges and future perspectives on the development of biochar-based adsorbents and their applications in addressing antibiotics. It concludes by summarizing the key findings and emphasizing the significance of biochar as a sustainable and effective solution for mitigating antibiotics contamination in industrial wastewater.

Enhanced Fenton-like catalysis via interfacial regulation of g-C3N4 for efficient aromatic organic pollutant degradation

For the efficient degradation of organic pollutants with the goal of reducing the water environment pollution, we employed an alkaline hydrothermal treatment on primeval g-C3N4 to synthesize a hydroxyl-grafted g-C3N4 (CN-0.5) material, from which we engineered a novel Fenton-like catalyst, known as Cu-CN-0.5. The introduction of numerous hydroxyl functional groups allowed the CN-0.5 substrate to stably fix active copper oxide particles through surface complexation, resulting in a low Cu leaching rate during a Cu-CN-0.5 Fenton-like process. A sequence of characterization techniques and theoretical calculations uncovered that interfacial complexation induced charge redistribution on the Cu-CN-0.5 surface. Specifically, some of the π electrons in the tris-s-triazine units were transferred to the copper oxide particles along the newly formed chemical bonds (C(π)-O-Cu), forming a π-deficient area on the tris-s-triazine plane near the complexation site. In a typical Cu-CN-0.5 Fenton-like process, a stable π-π interaction was established due to the favorable positive-negative match of electrostatic potential between the aromatic pollutants and π-deficient areas, leading to a significant improvement in Cu-CN-0.5's adsorption capacity for aromatic pollutants. Furthermore, pollutants also delivered electrons to the Cu-CN-0.5 Fenton-like system via a "through-space" approach, which suppressed the futile oxidation of H2O2 in reducing the high-valent Cu2+ and significantly improved the generation efficiency of •OH with high oxidative capacity. As expected, Cu-CN-0.5 not only exhibited an efficient Fenton degradation for several typical aromatic organic pollutants, but also demonstrated both a low metal leaching rate (0.12 mg/L) and a H2O2 utilization rate exceeding 80%. The distinctive Fenton degradation mechanism substantiated the potential of the as-prepared material for effective wastewater treatment applications.

Novel enhanced defluorination of perfluorooctanoic acids by biochar-assisted ultrasound coupling ferrate: Performance and mechanism

An ultrasound (US)/biochar (BC)/ferrate (Fe (VI)) system was firstly proposed to enhance perfluorooctanoic acid (PFOA) defluorination. It achieved 93 % defluorination optimally, higher than the sum of 77 % (28 % and 49 % for US/BC and US/Fe (VI) respectively), implying synergistic effect. Besides, the mechanism study confirmed that, this system can not only increase the specific surface area of BC and the generation of reactive oxidant species (ROS), enriching the active sites and forming new oxygen-containing functional groups, but also promote the formation of intermediate iron species. The PFOA degradation in the US/BC/Fe (VI) was probably an adsorption-degradation process, both ROS and electron transfer promoted the defluorination. Additionally, its sustainability was also demonstrated with 14 % reduced defluorination percentage after five cycles of BC. Overall, the synergistic effect of the US/BC/Fe (VI) and its enhancing mechanism for PFOA defluorination were clarified firstly, which contributes to the development of biochar for assisting polyfluoroalkyl substances degradation.

Advancements in application of modified biochar as a green and low-cost adsorbent for wastewater remediation from organic dyes

Synthetic organic dyes, which are resistant to biodegradation, pose a notable health risk, potentially leading to cancer and respiratory infections. Researchers have addressed this concern by exploring physicochemical methods to remove organic dyes from wastewater. A particularly promising solution involves modified biochar adsorbents, which demonstrate high efficiency in organic dye removal. Biochar, a charcoal-like material derived from biomass pyrolysis, offers advantages such as low cost, eco-friendliness, high efficiency and reusability. Beyond its role in sustainable soil remediation, biochar proves effective in removing organic dyes from wastewater after undergoing physical or chemical modification. Acid-base activation or metal-heteroatom impregnation enhances biochar's adsorption capacity. This comprehensive review examines the attributes of biochar, common methods for production and modification, and the impacts of raw materials, pyrolysis temperature, heating rate and residence time. It further elucidates the biochar adsorption mechanism in the removal of organic dyes, assessing factors influencing efficiency, including biochar feedstock, solution pH, adsorption temperature, particle size, initial dye concentration, biochar dosage and reaction time. It explores challenges, opportunities, reusability and regeneration methods of biochar in treating organic dye wastewater. It also discusses recent advances in organic dye removal using adsorption-based biochar. The review ultimately advocates for enhancing biochar's adsorption performance through post-modification.

Bismuth oxymetallate-modified biochar derived from Euryale ferox husk for efficient removal of Congo red from wastewater: adsorption behavior and mechanisms

Using Euryale ferox husk as raw material, pristine biochar (EBC), Bi2MoO6-modified biochar (BM-EBC), and BiFeO3-modified biochar (BF-EBC) were prepared and employed for decontaminating Congo red (CR) from wastewater. Compared with EBC (217.59 mg/g) and BF-EBC (359.49 mg/g), a superior adsorption capacity of 460.77 mg/g was achieved by BM-EBC. Based on the evaluation results of the Freundlich and pseudo-second-order models, multilayer chemisorption was suggested as the adsorption mechanism. The adsorption process of BM-EBC was spontaneous and endothermic, and the rate-limiting step pertained to liquid film diffusion and intraparticle diffusion. The underlying removal mechanism was explored via SEM, BET, FTIR, XPS, Raman spectra, and Zeta potential analyses. The introduction of bismuth oxymetallates with their high number of M-O (M: Bi, Mo, Fe) structural elements provided the adsorbent with enlarged surface areas and reinforced oxygen functional groups, thereby promoting pore filling, π-π interactions, hydrogen bonding, and complexation, leading to enhanced adsorption capacity. These results demonstrate that Euryale ferox husk biochar modified by bismuth oxymetallates has high prospects for valorizing biomass waste and removing CR from wastewater.

Different crystalline manganese dioxide and biochar co-conditioning aerobic composting: Reduced ammonia volatilization and improved organic fertilizer quality

Aerobic composting is a sustainable and effective waste disposal method. However, it can generate massive amounts of ammonia (NH3) via volatilization. Effectively reducing NH3 volatilization is vital for advancing aerobic composting and protecting the ecological environment. Herein, two crystal types of MnO2 (α-MnO2 and δ-MnO2) are combined with biochar (hydrochar (WHC) and pyrochar (WPC), respectively) and used as conditioners for the aerobic composting of chicken manure. Results reveal that α-MnO2 (34.6%) can more effectively reduce NH3 accumulation than δ-MnO2 (27.1%). Moreover, the combination of WHC and MnO2 better reduces NH3 volatilization (48.5-58.9%) than the combination of WPC and MnO2 (15.8-40.1%). The highest NH3 volatilization reduction effect (58.9%) is achieved using the combination of WHC and δ-MnO2. Because the added WHC and δ-MnO2 promote the humification of the compost, the humic acid to fulvic acid ratio (HA/FA ratio) dramatically increases. The combination of WHC and δ-MnO2 doubled the HA/FA ratio and resulted in a net economic benefit of 130.0 RMB/t. Therefore, WHC and δ-MnO2 co-conditioning can promote compost decomposition, improving the quality of organic fertilizers and substantially reducing NH3 volatilization.

Research Progress on the Degradation of Organic Pollutants in Water by Activated Persulfate Using Biochar-Loaded Nano Zero-Valent Iron

Biochar (BC) is a new type of carbon material with a high specific surface area, porous structure, and good adsorption capacity, which can effectively adsorb and enrich organic pollutants. Meanwhile, nano zero-valent iron (nZVI) has excellent catalytic activity and can rapidly degrade organic pollutants through reduction and oxidation reactions. The combined utilization of BC and nZVI can not only give full play to their advantages in the adsorption and catalytic degradation of organic pollutants, but also help to reduce the agglomeration of nZVI, thus improving its efficiency in water treatment and providing strong technical support for water resources protection and environmental quality improvement. This article provides a detailed introduction to the preparation method and characterization technology, reaction mechanism, influencing factors, and specific applications of BC and nZVI, and elaborates on the research progress of BC-nZVI in activating persulfate (PS) to degrade organic pollutants in water. It has been proven experimentally that BC-nZVI can effectively remove phenols, dyes, pesticides, and other organic pollutants. Meanwhile, in response to the existing problems in current research, this article proposes future research directions and challenges, and summarizes the application prospects and development trends of BC-nZVI in water treatment. In summary, BC-nZVI-activated PS is an efficient technology for degrading organic pollutants in water, providing an effective solution for protecting water resources and improving environmental quality, and has significant application value.

Efficient and Selective Removal of Heavy Metals and Dyes from Aqueous Solutions Using Guipi Residue-Based Hydrogel

The presence of organic dyes and heavy metal ions in water sources poses a significant threat to human health and the ecosystem. In this study, hydrogel adsorbents for water pollution remediation were synthesized using Guipi residue (GP), a cellulose material from Chinese herbal medicine, and chitosan (CTS) through radical polymerization with acrylamide (AM) and acrylic acid (AA). The characteristics of the hydrogels were analyzed from a physicochemical perspective, and their ability to adsorb was tested using model pollutants such as Pb2+, Cd2+, Rhodamine B (RhB), and methyl orange (MO). The outcomes revealed that GP/CTS/AA-co-AM, which has improved mechanical attributes, effectively eliminated these pollutants. At a pH of 4.0, a contact duration of 120 min, and an initial concentration of 600 mg/L for Pb2+ and 500 mg/L for Cd2+, the highest adsorption capabilities were 314.6 mg/g for Pb2+ and 289.1 mg/g for Cd2+. Regarding the dyes, the GP/CTS/AA-co-AM hydrogel displayed adsorption capacities of 106.4 mg/g for RhB and 94.8 mg/g for MO, maintaining a stable adsorption capacity at different pHs. Compared with other competitive pollutants, GP/CTS/AA-co-AM demonstrated a higher absorption capability, mainly targeted toward Pb2+. The adsorption processes for the pollutants conformed to pseudo-second-order kinetics models and adhered to the Langmuir models. Even after undergoing five consecutive adsorption and desorption cycles, the adsorption capacities for heavy metals and dyes remained above 70% and 80%. In summary, this study effectively suggested the potential of the innovative GP/CTS/AA-co-AM hydrogel as a practical and feasible approach for eliminating heavy metals and dyes from water solutions.

Recent trends and economic significance of modified/functionalized biochars for remediation of environmental pollutants

The pollution of soil and aquatic systems by inorganic and organic chemicals has become a global concern. Economical, eco-friendly, and sustainable solutions are direly required to alleviate the deleterious effects of these chemicals to ensure human well-being and environmental sustainability. In recent decades, biochar has emerged as an efficient material encompassing huge potential to decontaminate a wide range of pollutants from soil and aquatic systems. However, the application of raw biochars for pollutant remediation is confronting a major challenge of not getting the desired decontamination results due to its specific properties. Thus, multiple functionalizing/modification techniques have been introduced to alter the physicochemical and molecular attributes of biochars to increase their efficacy in environmental remediation. This review provides a comprehensive overview of the latest advancements in developing multiple functionalized/modified biochars via biological and other physiochemical techniques. Related mechanisms and further applications of multiple modified biochar in soil and water systems remediation have been discussed and summarized. Furthermore, existing research gaps and challenges are discussed, as well as further study needs are suggested. This work epitomizes the scientific prospects for a complete understanding of employing modified biochar as an efficient candidate for the decontamination of polluted soil and water systems for regenerative development.

Peroxymonosulfate activation by Fe-Mn Co-doped biochar for carbamazepine degradation

Antibiotics in aquatic environments present a serious threat to the ecological environment and human health. Activation of carbon-catalyzed persulfate is a prospective approach for oxidizing antibiotics. There is a pressing need for inexpensive carbon catalysts of high quality. In this study, biochar (BC) modified by Fe, Mn and Fe@Mn was employed to activate peroxymonosulfate (PMS) to degrade carbamazepine (CBZ) in water. The surface of Fe@Mn BC had a dense, stalactite-like morphology comprising a square chassis that was elliptical. The catalyst Fe@Mn-BC possessed the optimal degradation effect (99%) on CBZ at 100 min. Electron paramagnetic resonance spectroscopy and the quenching spectrum suggested that ˙O2- and 1O2 contributed to CBZ degradation.

Recent advances in the synthesis and application of magnetic biochar for wastewater treatment

Magnetic biochar (MBC) is a novel bio-carbon material with both desired properties as adsorbent and magnetic characteristics. This review provides an up-to-date summary and discussion on the latest development of MBC, which covers the progress on its synthesis, application, and techno-economic analysis. The review indicates that the direct hydrothermal synthesis has been catching more research attention to produce MBC due to its mild reaction conditions. Instead of the Fe-loaded MBC, there is a trend of using Mn for the magnetization. For the MBC application, how to improve its adsorption performance for water decontamination, ideally to match that of the biochar (BC) or activated carbon, is important. In addition, more studies on the environmental impacts of MBC and life-cycle assessment decoding the process optimization options are necessary. This review will provide valuable references for the development of MBC and MBC-based materials for wastewater treatment.

Synthesis and characterization of nanobiochar from rice husk biochar for the removal of safranin and malachite green from water

Xenobiotic pollution in environment is a potential risk to marine life, and human health. Nanobiotechnology is an advanced and emerging solution for the removal of environmental pollutants. Adsorption-based technologies are being used to alleviate the global prevalence of xenobiotics like dyes, due to their high efficacy and cost effectiveness. Current study explored the potential of nanobiochar syntehsized via ultrasonication and centrifugation from rice husk for dye removal from water. It involves the synthesis of nanobiochar from rice husk biochar for removal of Safranin, Malachite green, and a mixture of both from aqueous water. Biochar was synthesized through pyrolysis at 600 °C for 2 h. To convert it into nanobiochar, sonication and centrifugation techniques were applied. The yield obtained was 27.5% for biochar and 0.9% for nanobiochar. Nanobiochar analysis through Fourier-Transform Spectrometer (FTIR), X-ray Power Diffraction (XRD) and scanning electron microscopy (SEM) suggested its crystalline nature having minerals rich in silicon, with a cracked and disintegrated carbon structure due to high temperature and processing treatments. Removal of dyes by nanobiochar was evaluated by changing different physical parameters i.e., nanobiochar dose, pH, and temperature. Pseudo-first order model and pseudo-second order model were applied to studying the adsorption kinetics mechanism. Kinetics for adsorption of dyes followed the pseudo-second order model suggesting the removal of dyes by process of chemical sorption. High adsorption was found at a higher concentration of nanobiochar, high temperature, and neutral pH. Maximum elimination percentages of safranin, malachite green, and a mixture of dyes were obtained as 91.7%, 87.5%, and 85% respectively. We conclude that nanobiochar could be a solution for dye removal from aqueous media.

On the adsorption characteristics and mechanism of methylene blue by ball mill modified biochar

In this study, modified biochar (BRB) was prepared from rice straw by ball milling technique and used for the adsorption of methylene blue (MB) in wastewater. The BRB was characterized by SEM, FTIR and XPS, and the adsorption model and Box-Behnken design were used to optimize the five influencing factors. The results showed that the ball milling technique could increase the content of functional groups (-OH, C=C and C-O, etc.) and aromatic structures on the surface of biochar, thus facilitating the removal of MB. The isotherm model was consistent with the Langmuir adsorption model (R2 = 0.947) and the maximum adsorption capacity was 50.27 mg/g. The adsorption kinetics was consistent with the pseudo-second-order kinetic model (R2 = 1) and the adsorption rate was mainly controlled by chemisorption. The thermodynamic model confirmed that the adsorption process was a spontaneous heat absorption reaction. The maximum adsorption efficiency was 99.78% under the optimal conditions (40℃, pH 8, reaction time = 90 min, dosing amount = 0.1 mg), and the adsorption efficiency could be improved by increasing the pH and BRB dosing amount. The surface functional groups and crystal structure properties of BRB were the main determinants of adsorption, and it was clarified that physical adsorption, electrostatic attraction and π-π interaction were the main mechanisms for the adsorption of MB by BRB. The main mechanisms were clarified. Therefore, BRB is an economic, efficient and green adsorption material with good potential for the removal of dye pollutants in the aqueous environment.

A novel biochar composite derived from oil-based drill sludge and cuttings: Structural characterization and electrochemical properties

How to dispose of large quantities of hazardous shale gas drilling waste is an important worldwide problem facing the oil and gas industry. In this study, we report an environmentally friendly and low energy consumption approach (carbonization followed by activation) to convert oil-based drill sludge (OBDS) and oil-based drill cuttings (OBDCs) into biochar composites and investigate the effect of hydrofluoric acid (HF) acidification on them. The biochar composites were prepared using the OBDS, OBDCs, the mixtures of OBDS and OBDCs, and HF treatment the mixtures were named OS, OC, OSC, and OSC-HF, respectively. The characterization result of synthesized biochar composites indicated that the OSC had a larger specific surface area and a higher degree of graphitization. The composites mainly consisted of SiO2 and BaSO4, except for biochar. The OSC electrode exhibited the highest oxygen evolution potential (1.72 V vs Ag/AgCl) and the lowest charge transfer resistance compared with OS, OC, and OSC-HF electrodes, implying that SiO2 plays an important role in electrochemical performance. Using the OSC electrode as an anode, the chemical oxygen demand removal efficiency of the OBDS supernatant was 79.4 ± 0.95%. Further, the OSC electrode could maintain higher degradation efficiency and stability after the fifth reuse. The study provides a promising route for the proper disposal and resource utilization of OBDS and OBDCs and proposes a novel biochar compound as an electrode for the efficient treatment of wastewater. Moreover, this work highlights the important significance of the simultaneous resource utilization of waste and the treatment of wastewater using waste materials.

A critical review on biochar production from pine wastes, upgradation techniques, environmental sustainability, and challenges

Pine wastes, including pine needles, cones, and wood, are abundantly produced as an agroforestry by-product globally and have shown tremendous potential for biochar production. Various thermochemical conversion technologies have exhibited promising results in converting pine wastes to biochar, displaying impressive performance. Hence, this review paper aims to investigate the possibilities and recent technological advancements for synthesizing biochar from pine waste. Furthermore, it explores techniques for enhancing the properties of biochar and its integrated applications in various fields, such as soil and water remediation, carbon sequestration, battery capacitor synthesis, and bio-coal production. Finally, the paper sheds light on the limitations of current strategies, emphasizing the need for further research and study to address the challenges in pine waste-based biochar synthesis. By promoting sustainable and effective utilization of pine wastes, this review contributes to environmental conservation and resource management.

Biochar loaded with CoFe2O4 enhances the formation of high-valent Fe(IV) and Co(IV) and oxygen vacancy in the peracetic acid activation system for enhanced antibiotic degradation

Corn straw and sludge-derived biochar composite (BC) loaded with CoFe2O4 was successfully prepared to activate peracetic acid (PAA) for efficient degradation of tetracycline hydrochloride (TCH). Within 60 s, 96 % TCH removal efficiency was achieved through a non-free radical degradation pathway, primarily driven by singlet oxygen (1O2). The mechanism involves the electron-rich groups on the biochar surface, which facilitate the cleavage of the PAA OO bond to generate •O2-/1O2 and provide electrons to induce the formation of high-valent Fe(IV) and Co(IV). The oxygen vacancies on the surface of the CoFe2O4-loaded biochar composite (CFB-2) contribute partially to 1O2 production through their transformation into a metastable intermediate with dissolved oxygen. Moreover, elevated temperatures further enhance PAA activation by CFB-2, leading to increased reactive oxygen species (ROS) production through PAA decomposition, thereby promoting TCH removal. This study offers new insights into the catalysis of metal-loaded biochar for efficient TCH degradation via non-free radical generation.

Surface acidic sites strengthened core-shell HC@MnO2 for enhanced gaseous ammonia adsorption

As a common gaseous pollutant in atmospheric environment, ammonia (NH3) not only contributes to the formation of haze, but also disturb the nitrogen balance in ecosystem through atmospheric nitrogen deposition. Therefore, the control of NH3 emission has important environmental significance. Adsorption is the most commonly used technology for NH3 purification in practice, and efficient adsorbents are the key to adsorption method. Herein, a core-shell structured HC@MnO2 adsorbent was constructed by in-situ growth of layered δ-MnO2 on hydrochar (HC) surface, and its surface acidic sites were further strengthened. The enhancement of surface acidic sites significantly improved the adsorption performance of HC@MnO2 for NH3, reaching 34.49 mg NH3/g, which was superior to commercial carbon-based materials (whose adsorption capacity was 8.47 times that of Coal-based activated carbon, 14.25 times that of Coconut shell activated carbon, and 12.77 times that of Bamboo charcoal). Moreover, the operating parameters and adsorption kinetics were detailly investigated. The adsorption of HC@MnO2 on NH3 was in accordance with pseudo-second-order adsorption kinetics model. Large surface area of core-shell structure and abundant surface acidic sites of δ-MnO2 are the decisive reasons for the excellent adsorption performance of HC@MnO2. Importantly, the enhancement of surface stronger Brønsted acidic sites is the key to improve NH3 adsorption performance of HC@MnO2. Finally, the thermal regeneration and recycling performance of HC@MnO2-H were also investigated. This study provides a suggestive for further research on low-cost composite materials with excellent NH3 adsorption performance.

Nitrogen amended graphene catalyses fast reduction of vinyl chloride by nano zerovalent iron

Vinyl chloride (VC) is a dominant carcinogenic residual in many aged chlorinated solvent plumes, and it remains a huge challenge to clean it up. Zerovalent iron (ZVI) is an effective reductant for many chlorinated compounds but shows low VC removal efficiency at field scale. Amendment of ZVI with a carbonaceous material may be used to both preconcentrate VC and facilitate redox reactions. In this study, nitrogen-doped graphene (NG) produced by a simple co-pyrolysis method using urea as nitrogen (N) source, was tested as a catalyst for VC reduction by nanoscale ZVI (nZVI). The extent of VC reduction to ethylene in the presence of 2 g/L of nZVI was less than 1% after 3 days, and barely improved with the addition of 4 g/L of graphene. In contrast, with amendment of nZVI with NG produced at pyrolysis temperature (PT) of 950 °C, the VC reduction extent increased more than 10-fold to 69%. The reactivity increased with NG PT increasing from 400 °C to an optimum at 950 °C, and it increased linearly with NG loadings. Interestingly, N dosage had little effect on reactivity if NG was produced at PT of 950 °C, while a positive correlation was observed for NG produced at PT of 600 °C. XPS and Raman analyses revealed that for NG produced at lower PT (<800 °C) mainly the content of pyridine-N-oxide (PNO) groups correlates with reactivity, while for NG produced at higher PT up to 950 °C, reactivity correlates mainly with N induced structural defects in graphene. The results of quenching and hydrogen yield experiments indicated that NG promote reduction of VC by storage of atomic hydrogen, thus increasing its availability for VC reduction, while likely also enabling electron transfer from nZVI to VC. Overall, these findings demonstrate effective chemical reduction of VC by a nZVI-NG composite, and they give insights into the effects of N doping on redox reactivity and hydrogen storage potential of carbonaceous materials.

Waste leather derived porous carbon boosted Fenton oxidation towards removal of diethyl phthalate: Mechanism and long-lasting performance

The acceleration of Fe(III)/Fe(II) conversion in Fenton systems is the critical route to achieve the long-lasting generation of reactive oxygen species towards the oxidation of refractory contaminants. Here, we found that waste leather derived porous carbon materials (LPC), as a simple and readily available metal-free biochar material, can promote the Fe(III)/H2O2 system to generate hydroxyl radicals (•OH) for oxidizing a broad spectrum of contaminants. Results of characterizations, theoretical calculations, and electrochemical tests show that the surface carbonyl groups of LPC can provide electron for direct Fe(III) reduction. More importantly, the graphitic-N on surface of LPC can enhance the reactivity of Fe(III) for accelerating H2O2 induced Fe(III) reduction. The presence of LPC accelerates the Fe(III)/Fe(II) redox cycle in the Fe(III)/H2O2 system, sustainable Fenton chain reactions is thus initiated for long-lasting generation of hydroxyl radicals without adding Fe(II). The continuous flow mode that couples in-situ Fenton-like oxidation and LPC with excellent adsorption catalytic properties, anti-coexisting substances interference and reusability performance enables efficient, green and sustainable degradation of trace organic pollutants. Therefore, the application of metal-free carbon materials in Fenton-like system can solve its rate-limiting problem, reduce the production of iron sludge, achieve green Fenton chemistry, and facilitate the actual engineering application of economic and ecological methods to efficiently remove trace organic contaminants from actual water sources.

Applications of Carbon-Based Materials in Activated Peroxymonosulfate for the Degradation of Organic Pollutants: A Review

In recent years, water pollution has posed a serious threat to aquatic organisms and humans. Advanced oxidation processes (AOPs) based on activated peroxymonosulfate (PMS) show high oxidation, good selectivity, wide pH range and no secondary pollution in the removal of organic pollutants in water. Carbon-based materials are emerging green catalysts that can effectively activate persulfates to generate radical and non-radical active species to degrade organic pollutants. Compared with transition metal catalysts, carbon-based materials are widely used in SR-AOPs because of their low cost, non-toxicity, acid and alkali resistance, large specific surface area, and scalable surface charge, which can be used for selective control of specific water pollutants. This paper mainly presents several carbon-based materials used to activate PMS, including raw carbon materials and modified carbon materials (heteroatom-doped and metal-doped), analyzes and summarizes the mechanism of activating PMS by carbon-based catalysts, and discusses the influencing factors (temperature, pH, PMS concentration, catalyst concentration, inorganic anions, inorganic cations and dissolved oxygen) in the activation process. Finally, the future challenges and prospects of carbon-based materials in water pollution control are also presented.

Polymeric hydrogels-based materials for wastewater treatment

Low-cost and reliable wastewater treatment is a relevant issue worldwide to reduce the concentration of environmental pollutants. Industrial effluents containing dyes, heavy metals, and other inorganic and organic compounds can pollute water resources; therefore, novel technologies are required to mitigate and control their release into the environment. Adsorption is one of the simplest methods for treating contaminated water in which a wide spectrum of adsorbents can be used to remove emerging compounds. Hydrogels are interesting materials with high adsorption capacities that can be synthesized via green routes. These adsorbents are promising for large-scale industrial wastewater treatment applications; however, gaps still exist in achieving sustainable commercial implementation. This review focuses on the discussion and analysis of preparation, characterization, and adsorption properties of hydrogels for water purification. The advantages of these polymeric materials for water treatment were analyzed, including their performance in the removal of different organic and inorganic contaminants. Recent advances in the functionalization of hydrogels and the synthesis of novel composites have also been described. The adsorption capacities of hydrogel-based adsorbents are higher than 500 mg/g for different organic and inorganic pollutants, and can reach values of up to >2000 mg/g for organic compounds, significantly outperforming other materials reported for water cleaning. The main interactions involved in the adsorption of water pollutants using hydrogel-based adsorbents were described and explained to allow the interpretation of their removal mechanisms. The current challenges in the implementation of hydrogels for water purification in real-life operations are also highlighted. This review provides an updated picture of hydrogels as interesting materials to address water depollution worldwide.

Efficient degradation of norfloxacin using a novel biochar-supported CuO/Fe3O4 combined with peroxydisulfate: Insights into enhanced contribution of nonradical pathway

Nonradical persulfate oxidation techniques have evolved as a new contaminated water treatment approach due to its great tolerance to water matrixes. The catalysts of CuO-based composites have received much attention in that aside from SO₄^•-/^•OH radicals, the nonradicals of singlet oxygen (¹O₂) can be also generated during persulfate activation via CuO. However, the issues regarding particles aggregation and metal leaching from the catalysts during the decontamination process remain to be addressed, which could have a remarkable impact on the catalytic degradation of organic pollutants. Accordingly in the present study, a novel biochar-supported bimetallic Fe₃O₄-CuO catalyst (CuFeBC) was facilely developed to activate peroxodisulfate (PDS) for the degradation of norfloxacin (NOR) in aqueous solution. The results showed CuFeBC has a superior stability against metal ions Cu/Fe leaching, and NOR (30 mg L^-1) was degraded at 94.5% within 180 min in the presence of CuFeBC (0.5 g L^-1) and PDS (6 mM) in pH 8.5. The scavenging of reactive oxygen species and electron spin resonance analysis revealed that ¹O₂ dominated the degradation of NOR. Compared with pristine CuO-Fe₃O₄, the interaction between biochar substrate and metal particles could significantly enhance the contribution of the nonradical pathway to NOR degradation from 49.6% to 84.7%. Biochar substrate could efficiently reduce the leaching of metal species from the catalyst, thereby maintaining excellent catalytic activity and lasting reusability of the catalyst. These findings could enlighten new insights into fine-tuning radical/nonradical processes from CuO-based catalysts for the efficient remediation of organic contaminants in polluted water.

The performance and mechanism of iron-mediated chemical oxidation: Advances in hydrogen peroxide, persulfate and percarbonate oxidation

Many studies have successfully built iron-mediated materials to activate or catalyze Fenton-like reactions, with applications in water and wastewater treatment being investigated. However, the developed materials are rarely compared with each other regarding their performance of organic contaminant removal. In this review, the recent advances of Fenton-like processes in homogeneous and heterogeneous ways are summarized, especially the performance and mechanism of activators including ferrous iron, zero valent iron, iron oxides, iron-loaded carbon, zeolite, and metal organic framework materials. Also, this work mainly compares three O-O bond containing oxidants including hydrogen dioxide, persulfate, and percarbonate, which are environmental-friendly oxidants and feasible for in-situ chemical oxidation. The influence of reaction conditions, catalyst properties and benefits are analyzed and compared. In addition, the challenges and strategies of these oxidants in applications and the major mechanisms of the oxidation process have been discussed. This work can help understand the mechanistic insights of variable Fenton-like reactions, the role of emerging iron-based materials, and provide guidance for choosing appropriate technologies when facing real-world water and wastewater applications.

The co-pyrolysis of waste urea-formaldehyde resin with pine sawdust: co-pyrolysis behavior, pyrocarbon and its adsorption performance for Cr (VI)

Urea-formaldehyde (UF) resin is difficult to degrade and classified as hazardous organic waste. To address this concern, the co-pyrolysis behavior of UF resin with pine sawdust (PS) was studied, and the adsorption properties of pyrocarbon were evaluated with Cr (VI). Thermogravimetric analysis revealed that adding a small amount of PS can improve the pyrolysis behavior of UF resin. Based on the Flynn Wall Ozawa (FWO) method, the kinetics and activation energy values were estimated. It was observed that when the amount of UF resin exceeded twice that of PS, the activation energy of the reaction decreased, and they acted synergistically. The characterization of pyrocarbon samples showed that the specific surface area increased with the increase of temperature, while the content of functional groups showed the opposite trend. Intermittent adsorption experiments showed that 5UF + PS₄₀₀ achieved 95% removal of 50 mg/L Cr (VI) at 0.6 g/L dosage and at pH 2. The adsorption process was consistent with the Langmuir isotherm and pseudo-second-order kinetics, and the maximum adsorption was 143.66 mg/g at 30 ℃. Furthermore, the adsorption process consisted of electrostatic adsorption, chelation, and redox reaction. Overall, this study provides a useful reference for the co-pyrolysis of UF resin and the adsorption capacity of pyrocarbon.

Removal of Pb(II) and phosphorus in water by γ-Al2O3/biochar

In this work, we synthesized activated alumina biochar composites (γ-Al₂O₃/BC) by sol-gel method, which improved the problem that the surface charge of γ-Al₂O₃ was not conducive to the removal of heavy metal cation in a neutral solution, and then explored the feasibility of removing Pb(II) by γ-Al₂O₃/BC as well as reusing Pb-laden waste sludge to remove phosphorus (P) and its micro-adsorption mechanisms. The results show that the maximum adsorption capacity of γ-Al₂O₃/BC for Pb(II) is 182.48 mg/g, and the removing capacity of recycled Pb-laden slag for P also reaches 87.13 mg/g. It was found that the presence of Pb in the slag makes P removal more effective. In addition, in the process of P removal, the Pb in the slag will not be released, which will not cause secondary pollution to the water. The micro-adsorption mechanism of Pb(II) and P on the composites was investigated by XPS, XRD, and FTIR. It demonstrates that special functional groups such as hydroxy-aluminum, hydroxyl, and carboxyl groups can remove Pb(II) through strong surface complexation and electrostatic attraction. Furthermore, the removal mechanism of P from Pb-laden sludge includes chemisorption and complexation, and the precipitation of P and Pb on the adsorbent surface is the main reason for the removal of P. Therefore, it is feasible to further effectively remove P by using the waste biochar containing Pb. The idea of this paper provides a potential method for the reuse of waste adsorbent.

Greener design and characterization of biochar/Fe3O4@SiO2-Ag magnetic nanocomposite as efficient catalyst for synthesis of bioactive benzylpyrazolyl coumarin derivatives

The study aimed to develop an efficient catalyst, biochar/Fe₃O₄@SiO₂-Ag magnetic nanocomposite, to synthesize bioactive benzylpyrazolyl coumarin derivatives through a one-pot multicomponent reaction. The catalyst was prepared using Ag nanoparticles synthesized with Lawsonia inermis leaf extract and carbon-based biochar obtained through pyrolysis of Eucalyptus globulus bark. The nanocomposite contained a silica-based interlayer, highly dispersed Ag nanoparticles, and a central magnetite core, which responded well to external fields. The biochar/Fe₃O₄@SiO₂-Ag nanocomposite showed excellent catalytic activity and could be easily recovered using an external magnet and reused five times without significant loss of performance. The resulting products were tested for antimicrobial activity and showed significant activity against various microorganisms.

Comparative study for sorption of arsenic on peanut shell biochar and modified peanut shell biochar

In this study, arsenite [As(III)] and arsenate [As(V)] removal efficiency of peanut shell biochar (PSB) and modified peanut shell biochar (MPSB) was compared in aqueous solutions. The modification was carried out with KMnO₄ and KOH. Sorption efficiency of MPSB was relatively higher than PSB at pH 6 for As(III) (86%) and for As(V) (91.26%) for initial concentration of 1 mg/L, adsorbent dose of 0.5 g/L and 240 min equilibrium time at 100 rpm. Freundlich isotherm and pseudo-second order kinetic model suggested possible multilayer chemisorption. Fourier transform infrared spectroscopy showed that -OH, C-C, CC and C-O-C groups contributed significantly in adsorption for both PSB and MPSB. Thermodynamic study showed that the adsorption process was spontaneous and endothermic. Regeneration studies revealed that PSB and MPSB can be successfully used for three cycles. This study established that peanut shell is a low-cost, environment friendly and efficient biochar for removal of arsenic from water.

Ferrihydrite-loaded water hyacinth-derived biochar for efficient removal of glyphosate from aqueous solution

Ferrihydrite-loaded water hyacinth-derived biochar (FH/WHBC) was prepared by in-situ precipitation method to treat glyphosate-containing wastewater. The adsorption properties and mechanism, and actual application potential were deeply studied. Results showed that the adsorption performance of FH/WHBC was closely related with the precipitation pH condition, and the adsorbent prepared at pH 5.0 possessed the highest adsorption capacity of 116.8 mg/g for glyphosate. The isothermal and kinetic experiments showed that the adsorption of glyphosate was consistent with Langmuir model, and the adsorption process was rapid and could be achieved within 30 min. The prepared FH/WHBC was more suitable for application under high acidity environment, and could maintain the great adsorption performances in the presence of most co-existing ions. Besides, it also possessed a good regenerability. Under dynamic condition, the adsorption performance of FH/WHBC was not affected even at high flow rate and high glyphosate concentration. Furthermore, the FH/WHBC can keep excellent removal efficiency for glyphosate in wastewater treatment, and the concentration of glyphosate can be reduced to 0.06 mg·L^-1, which was lower than the groundwater quality of class II mandated in China. Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) characterization indicated that the adsorption of glyphosate on FH/WHBC was mainly accomplished through electrostatic adsorption and the formation of inner-sphere complexes. In brief, the prepared sorbent FH/WHBC was expected to be used in the treatment of industrial glyphosate wastewater.

Synergistic effect of hydrogen bonding and π-π interaction for enhanced adsorption of rhodamine B from water using corn straw biochar

Dyes adsorption to biochar via hydrogen bonding, and π-π interaction alone have attracted much research attention, however, their synergism in adsorption mechanisms remains largely unnoticed. The synergistic effects of the hydrogen bonding and π-π interaction might improve the adsorption capacity and need more understanding to prepare high-capacity biochar. In this work, we evaluated the adsorption of various dyes on biochar prepared via the activation of potassium bicarbonate and urea (named BC-KN) to explore their synergistic effects. Batch experiments indicated the BC-KN showed a high adsorption capacity to rhodamine B at 4839.0 mg/g, azure B at 4477.7 mg/g, and methylene blue at 2223.0 mg/g, respectively. The mechanism of such significant adsorption was investigated by their comparative experiments, characterizations, and computational analyses. The computational analyses suggested that the synergism of the hydrogen bonding and π-π interaction improves the adsorption energies of BC-KN/RhB system from -10.35 kcal/mol to -20.49 kcal/mol. It can be concluded that the hydrogen bonding and π-π interaction can synergize to significantly improve the adsorption by increasing the π-electron density and shortening the distance of aromatic rings, thus dyes with H-donor show significantly better adsorption capacities. The insight of hydrogen bonding being the governing factor in the synergistic system will help produce high-capacity biochar in removing aromatic dyes and suggest a sustainable technology for the efficient decolorization of dye effluent to minimize its damage to the health and environment.

Controlling waste by waste: a modified landfill leachate coagulation sludge activated peroxymonosulfate process achieves complete BPA degradation

In this study, a modified coagulation sludge (MCS) from a real landfill leachate coagulation pretreatment was first prepared with polymerized ferric sulfate (PFS) as the activator for PMS to degrade bisphenol A (BPA). The results showed that 43.34% of BPA was adsorbed by MCS when [BPA]₀ = 20 mg/L, [MCS]₀ = 0.8 g/L, and time = 80 min. Thereafter, by adding 3000 mg/L PMS to initiate the oxidation process, complete BPA removal, i.e. 100%, was achieved in 60 min. In addition, in tap water and municipal wastewater scenarios, 100% and 90.07% removal of BPA were obtained, respectively, and MCS exhibited outstanding performance after repeated use. MCS displayed an excellent adsorption capacity in which chemical adsorption was the main effect, and hydroxyl radicals were the major contributor to BPA degradation. Characterizations of fresh and reacted MCS were conducted, and the results showed that the MCS structure was stable after repeated use, and the surface functional groups, surface defect sites, and iron oxides participated in PMS activation. Overall, this study demonstrated successful recycling of coagulation sludge from landfill leachate pretreatment to activate PMS for environmental pollution control, which is in accordance with the goal of using waste to control waste.

Synthesis of an Environmentally Friendly Modified Mulberry Branch-Derived Biochar Composite: High Degradation Efficiency of BPA and Mitigation of Toxicity in Silkworm Larvae

In the present study, mulberry branch-derived biochar CuO (MBC/CuO) composite was successfully synthesized and used as a catalyst to activate persulfate (PS) for the degradation of bisphenol A (BPA). The MBC/CuO/PS system exhibited a high degradation efficiency (93%) of BPA, under the conditions of 0.1 g/L MBC/CuO, 1.0 mM PS, 10 mg/L BPA. Free radical quenching and electron spin-resonance spectroscopy (ESR) experiments confirmed that both free radicals ^•OH, SO₄^•- and O₂^•- and non-radicals ¹O₂ were involved in the MBC/CuO reaction system. Cl^- and NOM displayed negligible influence on the degradation of BPA, while HCO₃^- promoted the removal of BPA. In addition, the toxicity tests of BPA, MBC/CuO and the degraded BPA solution were conducted by the 5th instar silkworm larvae. The toxicity of BPA was reduced after the treatment in the MBC/CuO/PS system, and no obvious toxicity of the synthesized MBC/CuO composite was found in the toxicity evaluation experiments. This work provides a new value-added utilization of mulberry branches as a cost-effective and environmentally friendly PS activator.

Characterization of isolated starch from Isatis indigotica Fort. root and anhydro-sugars preparation using its decoction residues

Isatis indigotica Fort. root (Ban-lan-gen, IIR), a traditional Chinese medicine (TCM), has an ancient and well-documented history for its medicinal properties. Aside from epigoitrin, indole alkaloids, and their corresponding derivatives as medicinal ingredients, it also contains lots of biomass such as starch. Herein, a new starch was isolated from IIR and the physicochemical properties such as amylose content, moisture content, ash content, morphology, thermal properties, and crystallography were characterized systematically. The amylose content of IIR starch was 19.84 ± 0.85%, and the size and shape of starch granules is ellipsoidal shape with sizes from 2 to 10 μm. IIR starch exhibited a C-type pattern and had 25.92% crystallinity (higher than that of corn starch). The gelatinization temperature of IIR starch was 58.68-75.41 °C, and its gelatinization enthalpy was ΔH gel = 4.33 J/g. After decocting, the IIR's residues can be used to prepare anhydro-sugars in a polar aprotic solvent. The total carbon yield of levoglucosan (LG), levoglucosenone (LGO), 5-hydroxymethylfurfural (HMF), and furfural (FF) could reach 69.81% from IIR's decoction residues in 1,4-dioxane with 15 mM H2SO4 as the catalyst. Further, the residues after dehydration were prepared into biochar by thermochemical conversion and the BET surface area of biochar was 1749.46 m2/g which has good application prospect in soil improvement and alleviates obstacles of IIR continuous cropping.

Biochar loaded with cobalt ferrate activated persulfate to degrade naphthalene

Considering the simple preparation of biochar and the excellent activation performance of cobalt ferrate material, a biochar supported cobalt ferrate composite was synthesized by a solvothermal method. The material was used to activate persulfate (PS) to degrade naphthalene (NAP) in water. The structure and morphology characterization showed that the composite (CoFe₂O₄-BC) was successfully prepared. Under the conditions of 0.25 g L^-1 CoFe₂O₄-BC and 1 mM PS, 90.6% NAP (the initial concentration was 0.1 mM) was degraded after 30 minutes. The degradation kinetics of NAP followed the pseudo-first-order kinetic model with a rate constant of 0.0645 min^-1. With the increase of the dosage of activator and PS, the removal rate of NAP could be increased to 99.5%. The coexistence of anions and humic acids inhibited the removal of NAP. The acid environment promoted the removal of NAP while the alkaline environment inhibited it. After four cycles of CoFe₂O₄-BC material, the removal rate of NAP decreased from 90.6% to 79.4%. The removal of TOC was about 45% after each cycle. After the first cycle, the concentration of leached cobalt ion and leached iron ion was about 310 μg L^-1 and 30 μg L^-1 respectively. The free radical quenching experiments showed that SO₄ ^-˙ and OH˙ were the main causes of NAP removal, and the possible degradation path of NAP was elucidated by DFT calculation.

Intermittent ultrasound retains cellulases unlock for enhanced cellulosic ethanol with high-porosity biochar for dye adsorption using desirable rice mutant straw

In this study, optimal ultrasound pretreatment was performed with recalcitrance-reduced rice mutant straw to effectively extract lignin and hemicellulose for improved cellulose accessibility. Intermittent ultrasound-assistant enzymatic hydrolyses were followed to maintain more cellulases unlock and less cellulose surface block with lignin for raised hexose yield at 81 % (% cellulose) and bioethanol concentration at 9.9 g/L, which was higher than those of other mechanical pretreatments as previously conducted. Using all enzyme-undigestible lignocellulose residues, this work generated the biochar with the highest porosity (S_BET at 2971 m²/g) among all biomass-based biochar obtained from previous studies. Furthermore, the biochar were respectively examined with high adsorption capacity for Congo red and methylene blue at 7946 mg/g and 861 mg/g. Therefore, this study has demonstrated a green-like process technology for high-yield bioethanol and high-porosity biochar with full biomass utilization by integrating optimal ultrasound pretreatment with intermittent ultrasound-assistant enzymatic hydrolyses of recalcitrance-reduced lignocellulose in crop straws.

Waste to catalyst: Role of agricultural waste in water and wastewater treatment

Presently, owing to the rapid development of industrialization and urbanization activities, a huge quantity of wastewater is generated that contain toxic chemical and heavy metals, imposing higher environmental jeopardies and affecting the life of living well-being and the economy of the counties, if not treated appropriately. Subsequently, the advancement in sustainable cost-effective wastewater treatment technology has attracted more attention from policymakers, legislators, and scientific communities. Therefore, the current review intends to highlight the recent development and applications of biochars and/or green nanoparticles (NPs) produced from agricultural waste via green routes in removing the refractory pollutants from water and wastewater. This review also highlights the contemporary application and mechanism of biochar-supported advanced oxidation processes (AOPs) for the removal of organic pollutants in water and wastewater. Although, the fabrication and application of agriculture waste-derived biochar and NPs are considered a greener approach, nevertheless, before scaling up production and application, its toxicological and life-cycle challenges must be taken into account. Furthermore, future efforts should be carried out towards process engineering to enhance the performance of green catalysts to improve the economy of the process.

A Critical Review of Snail Shell Material Modification for Applications in Wastewater Treatment

Sea material is becoming increasingly popular and widely used as an adsorbent in wastewater treatment. Snail shell, a low-cost and natural animal waste material, has been shown to have a high calcium content (>99%) and a large potential surface area for the development of sustainable adsorbents. This paper presents a novel synthesis of methods for using snail shell absorbent materials in the treatment of wastewater containing heavy metals, textile dyes, and other organic substances. Modified biochar made from snail shells has gained popularity in recent years due to its numerous benefits. This paper discusses and analyzes modification methods, including impregnating with supplements, combining other adsorbents, synthesis of hydroxyapatite, co-precipitation, and the sol-gel method. The analysis of factors influencing adsorption efficiency revealed that pH, contact time, temperature, initial concentration, and adsorbent dose all have a significant impact on the adsorption process. Future research directions are also discussed in this paper as a result of presenting challenges for current snail adsorbents.

Degradation of organic pollutants from water by biochar-assisted advanced oxidation processes: Mechanisms and applications

Biochar has shown large potential in environmental remediation because of its low cost, large specific surface area, porosity, and high conductivity. Biochar-assisted advanced oxidation processes (BC-AOPs) have recently attracted increasing attention to the remediation of organic pollutants from water. However, the effects of biochar properties on catalytic performance need to be further explored. There are still controversial and knowledge gaps in the reaction mechanisms of BC-AOPs, and regeneration methods of biochar catalysts are lacking. Therefore, it is necessary to systematically review the latest research progress of BC-AOPs in the treatment of organic pollutants in water. In this review, first of all, the effects of biochar properties on catalytic activity are summarized. The biochar properties can be optimized by changing the feedstocks, preparation conditions, and modification methods. Secondly, the catalytic active sites and degradation mechanisms are explored in different BC-AOPs. Different influencing factors on the degradation process are analyzed. Then, the applications of BC-AOPs in environmental remediation and regeneration methods of different biochar catalysts are summarized. Finally, the development prospects and challenges of biochar catalysts in environmental remediation are put forward, and some suggestions for future development are proposed.

Removal Efficiency and Performance Optimization of Organic Pollutants in Wastewater Using New Biochar Composites

The purpose is to optimize the catalytic performance of biochar (BC), improve the removal effect of BC composites on organic pollutants in wastewater, and promote the recycling and sustainable utilization of water resources. Firstly, the various characteristics and preparation principles of new BC are discussed. Secondly, the types of organic pollutants in wastewater and their removal principles are discussed. Finally, based on the principle of removing organic pollutants, BC/zero valent iron (BC/ZVI) composite is designed, among which BC is mainly used for catalysis. The effect of BC/ZVI in removing tetracycline (TC) is comprehensively evaluated. The research results reveal that the TC removal effect of pure BC is not ideal, and that of ZVI is general. The BC/ZVI composite prepared by combining the two has a better removal effect on TC, with a removal amount of about 275 mg/g. Different TC concentrations, ethylene diamine tetraacetic acid (EDTA), pH environment, tert-butanol, and calcium ions will affect the TC removal effect of BC composites. The overall effect is the improvement of the TC removal amount of BC composites. It reveals that BC has a very suitable catalytic effect on ZVI, and the performance of BC composite material integrating BC catalyst and ZVI has been effectively improved, which can play a very suitable role in wastewater treatment. This exploration provides a technical reference for the effective removal of organic pollutants in wastewater and contributes to the development of water resource recycling.

Preparation of hydrochar bio-based catalyst for fenton process in dye-containing wastewater treatment

The use of synthetic dyes in the textile industry pollutes a huge amount of water. Thus, wastewater discharged from many textile companies to the receiving environment without being treated causes serious environmental and human health problems. The development of new techniques has become imperative. In this study, it was aimed to remove anionic dye (RR180) and cationic dye (BR18) by Fenton-like and adsorption process with hydrochars obtained from laurel leaves and watermelon peels. In the comparison of the adsorption and Fenton-like processes used in the dye removal of the produced bio-based materials, the Fenton-like process was selected in order to enhance the highest removal efficiency. The effects of various operating factors such as solution pH, amount of catalysts, hydrogen peroxide (H₂O₂) concentration, and initial dye concentration were evaluated on both dyes removal. The experimental results demonstrated that 99.8% RR180 dye and 98.8% BR18 dye removal efficiency were observed for an initial dye concentration of 100 mg/L with an adsorbent concentration of 1 g/L, H₂O₂ concentration of 15 μL/L, and optimum pH at the end of 60 min of reaction time. It was observed that an increase in initial dye concentration caused to decrease the dye removal efficiency. The optimum pH for the highest RR180 and BR18 dye removal was 4 and 6, respectively. It was observed that the increase in H₂O₂ concentration in the solution also decreased the dye removal efficiency. It turned out that catalysts obtained from hydrochars are an effective process for the high removal performance of cationic and anionic dyes.

Preparation of magnetic biochar and its catalytic role in degradation of Cu-EDTA by heterogeneous Fenton reaction

In this study, magnetic biochar (Fe-BC) was synthesized from phoenix tree leaves and FeSO₄·7H₂O by impregnation-pyrolysis method, and was used to activate H₂O₂ to degrade Cu-EDTA. The effects of preparation parameters on the degradation of Cu-EDTA by Fe-BC/H₂O₂ system were investigated by degradation experiments and characterization methods (SEM, BET, FTIR, XRD and XPS). The results showed that the magnetic biochar prepared under the pyrolysis temperature of 400 °C, pyrolysis time of 3 h and iron content of 3 wt% had the best catalytic activity. Within 120 min, the breaking efficiency of Cu-EDTA binding, precipitation efficiency of Cu²⁺ and removal efficiency of TOC could reach 78.48, 71.65 and 46.54% at the conditions of adding 1.0 g/L magnetic biochar and 25 mM H₂O₂ and the iron dissolution was only 0.32 mg/L. The characterization results and comparison experiments demonstrated that the catalytic effect of magnetic biochar not only depends on the transfer of electrons to H₂O₂ by the loaded iron oxides, but also the active oxygen functional groups (OFGs) and persistent free radicals (PFRs) contained on the surface can transfer electrons to H₂O₂ or even dissolved oxygen to produce an amount of hydroxyl radicals (^·OH) and superoxide anion radicals (O₂^·-).