Advances in technological control of greenhouse gas emissions from wastewater in the context of circular economy

Effects of carbon-based conductive materials on semi-continuous anaerobic co-digestion of organic fraction of municipal solid waste and waste activated sludge

Organic fraction of municipal solid waste (OFMSW) and waste activated sludge (WAS) are the most produced organic waste streams in urban centres. Their anaerobic co-digestion (AcoD) allows to generate methane (CH4) and digestate employable as renewable energy source and soil amendment, respectively, fully in accordance with circular bioeconomy principles. However, the widespread adoption of such technology is limited by relatively low CH4 yields that fail to bridge the gap between benefits and costs. Among strategies to boost AcoD of OFMSW and WAS, use of conductive materials (CMs) to promote interspecies electron transfer has gained increasing attention. This paper presents one of the few experimental attempts of investigating the effects of four different carbon(C)-based CMs (i.e., granular activated carbon - GAC, graphite - GR, graphene oxide - GO, and carbon nanotubes - CNTs) separately added in semi-continuous AcoD of OFMSW and thickened WAS. The presence of C-based CMs has been observed to improve CH4 yield of the control process. Specifically, after 63 days of operation (concentrations of GAC and GR of 10.0 g/L and of GO and CNTs of 0.2 g/L), 0.186 NL/gVS, 0.191 NL/gVS, 0.203 NL/gVS, and 0.195 NL/gVS of CH4 were produced in reactors supplemented with GAC, GR, GO, and CNTs, respectively, compared to 0.177 NL/gVS produced in the control process. Likewise, at the end of the test (i.e., after 105 days at concentrations of C-based CMs half of the initial ones), CH4 yields were 0.193 NL/gVS, 0.201 NL/gVS, 0.211 NL/gVS, and 0.206 NL/gVS in reactors supplemented with GAC, GR, GO, and CNTs, respectively, compared to 0.186 NL/gVS of the control process. Especially with regard to GR, GO, and CNTs, results obtained in the present study represent a significant advance of the knowledge on the effects of such C-based CMs to realistic and scalable AD process conditions respect to previous literature.

Applications of engineered biochar in remediation of heavy metal(loid)s pollution from wastewater: Current perspectives toward sustainable development goals

Environmental pollution of heavy metal(loid)s (HMs) caused adverse impacts, has become one of the emerging concerns and challenges worldwide. Metal(loid)s can pose significant threats to living organisms even when present in trace levels within environmental matrices. Extended exposure to these substances can lead to adverse health consequences in humans. Removing HM-contaminated water and moving toward sustainable development goals (SDGs) is critical. In this mission, biochar has recently gained attention in the environmental sector as a green and alternative material for wastewater removal. This work provides a comprehensive analysis of the remediation of typical HMs by biochars, associated with an understanding of remediation mechanisms, and gives practical solutions for ecologically sustainable. Applying engineered biochar in various fields, especially with nanoscale biochar-aided wastewater treatment approaches, can eliminate hazardous metal(loid) contaminants, highlighting an environmentally friendly and low-cost method. Surface modification of engineered biochar with nanomaterials is a potential strategy that positively influences its sorption capacity to remove contaminants. The research findings highlighted the biochars' ability to adsorb HM ions based on increased specific surface area (SSA), heightened porosity, and forming inner-sphere complexes with oxygen-rich groups. Utilizing biochar modification emerged as a viable approach for addressing lead (Pb), cadmium (Cd), arsenic (As), mercury (Hg), and chromium (Cr) pollution in aqueous environments. Most biochars investigated demonstrated a removal efficiency >90 % (Cd, As, Hg) and can reach an impressive 99 % (Pb and Cr). Furthermore, biochar and advanced engineered applications are also considered alternative solutions based on the circular economy.

Low-Cost Greywater Treatment Using Polyculture Microalgae-Microalgal Growth, Organics, and Nutrient Removal Subject to pH and Temperature Variations During the Treatment

Organics and nutrient removal studies are rarely done using polyculture microalgae, and that too in outdoor conditions, as they are often not deemed effective for wastewater treatment purposes. This study examined the organics and nutrient removal efficiency of polyculture microalgae cultivated in greywater. The reactor was operated in outdoor conditions. Hence, it was subjected to natural pH and temperature variations. A growth rate of 0.05 g L-1 day-1 was observed for temperatures up to 37 °C, beyond which the growth rate declined by 0.07 g L-1 day-1. During the treatment, the pH of the system was observed to be between 7.4 and 8.4. However, the growth rate would again pick up (0.05 g L-1 day-1) when the pH and temperature moved towards the optimum range, indicating that the polycultures adapt very quickly to their environment. The maximum biomass concentration reached 0.82 gL-1. The highest removal efficiency of organic carbon, ammonia, and phosphate was 80.7, 61.9, and 58.4%, respectively. Nitrate and nitrite concentrations remained ≤ 1.3 mgL-1 and ≤ 2 mgL-1, respectively, indicating the absence of nitrification/denitrification and ammonia volatilization. The mass balance of microalgae indicated that the primary removal mechanism of nitrogen and phosphorus removal was assimilation by the microalgae. The study proved polyculture microalgae to be as effective as some monoculture species in wastewater treatment, which require costlier controlled growth conditions. The high organics and nutrient removal by polycultures in outdoor conditions could pave the way to reducing wastewater treatment costs.

Biological performance and membrane fouling of a microalgal-bacterial membrane photobioreactor for wastewater treatment without external aeration and carbonation

Biological nutrient removal processes involving the use of activated sludge (AS) to treat municipal wastewater normally result in high aeration energy consumption and significant greenhouse gas (GHG) emissions. Therefore, developing cost-efficient and environmentally friendly processes for wastewater treatment is vital. In this work, a novel non-aerated microalgal-bacterial membrane photobioreactor (MB-MPBR) was proposed, and its feasibility for organic contaminant and nutrient removals was evaluated, for the first time. The effects of inoculation ratio (microalgae to bacteria (M/B)) on the biological performance and membrane fouling were systematically investigated. The results showed that 95.9% of the chemical oxygen demand (COD), 74.5% of total nitrogen (TN), 98.5% of NH4+-N and 42.0% of total phosphorus (TP) were removed at an inoculation M/B ratio of 3:2 at steady state, representing a significant improvement compared to the M/B inoculation ratio of 1:3. Additionally, the higher inoculation M/B ratio (3:2) significantly promoted the biomass production owing to the favorable mutual exchange of oxygen and carbon dioxide between microalgae and bacteria. Cake layer formation was the primary fouling mechanism owing to the absence of aeration scouring on the membrane surface. The membrane fouling rate was slightly higher at the higher inoculation ratio (M/B = 3:2) owing to the increased biomass and extracellular polymeric substances (EPS) productions, despite the larger particle size. These results demonstrated that the non-aerated MB-MPBR could achieve superior biological performance, of which the inoculation M/B ratio was of critical importance for the initiation and maintenance of microalgal-bacterial symbiotic system, yet possibly caused severer membrane fouling in the absence of external aeration and carbonation. This study provides a new perspective for further optimizing and applying non-aerated MB-MPBR to enhance municipal wastewater treatment.

Life cycle assessment and technoeconomic analysis of biofuels produced from polyculture microalgae cultivated in greywater

This study evaluated the environmental and economic impacts of substituting synthetic media with greywater for cultivating microalgae in the biofuel production process. Life cycle assessment (LCA) and technoeconomic assessment (TEA) were employed to compare the impacts of two scenarios - one containing bold's basal (BB) media and another containing greywater as growth mediums for microalgae cultivation. Scenarios 1 and 2 mitigated 1.74 and 2.14 kg CO2 per kg of biofuel production, respectively. Substituting BB media with greywater resulted in a 16.3% reduction in energy requirements, leading to a 79.3% increase in net energy recovered. LCA findings demonstrate a reduction in all seven environmental categories. TEA reveals that, despite a 21.7% higher capital investment, scenario 2 proves more economically viable due to a 39.8% lower operating cost and additional revenue from wastewater treatment and carbon credits. The minimum selling price of biofuel dropped from Rs 73.5/kg to Rs 36.5/kg, highlighting the economic and environmental advantages of substituting BB media with greywater in microalgal biofuel production.

Microalgae to biodiesel: A novel green conversion method for high-quality lipids recovery and in-situ transesterification to fatty acid methyl esters

Greenhouse gases (GHGs) emissions due to increasing energy demand have raised the need to identify effective solutions to produce clean and renewable energy. Biotechnologies are an effective platform to attain green transition objectives, especially when synergically integrated to promote health and environmental protection. In this context, microalgae-based biotechnologies are considered among the most effective tools for treating gaseous effluents and simultaneously capturing carbon sources for further biomass valorisation. The production of biodiesel is regarded as a promising avenue for harnessing value from residual algal biomass. Nonetheless, the existing techniques for extracting lipids still face certain limitations, primarily centred around the cost-effectiveness of the process.This study is dedicated to developing and optimising an innovative and cost-efficient technique for extracting lipids from algal biomass produced during gaseous emissions treatment based on algal-bacterial biotechnology. This integrated treatment technology combines a bio-scrubber for degrading gaseous contaminants and a photobioreactor for capturing the produced CO2 within valuable algal biomass. The cultivated biomass is then processed with the process newly designed to extract lipids simultaneously transesterificated in fatty acid methyl esters (FAME) via In Situ Transesterification (IST) with a Kumagawa-type extractor. The results of this study demonstrated the potential application of the optimised method to overcome the gap to green transition. Energy production was obtained from residuals produced during the necessary treatment of gaseous emissions. Using hexane-methanol (v/v = 19:1) mixture in the presence KOH in Kumagawa extractor lipids were extracted with extraction yield higher than 12% and converted in fatty acid methyl esters. The process showed the enhanced extraction of lipids converted in bio-sourced fuels with circular economy approach, broadening the applicability of biotechnologies as sustainable tools for energy source diversification.

Carbon neutrality in wastewater treatment plants: An integrated biotechnological-based solution for nutrients recovery, odour abatement and CO2 conversion in alternative energy drivers

Wastewater treatment plants play a crucial role in water security and sanitation, ensuring ecosystems balance and avoiding significant negative effects on humans and environment. However, they determine also negative pressures, including greenhouse gas and odourous emissions, which should be minimized to mitigate climate changes besides avoiding complaints. The research has been focused on the validation of an innovative integrated biological system for the sustainable treatment of complex gaseous emissions from wastewater treatment plants. The proposed system consists of a moving bed biofilm reactor coupled with an algal photobioreactor, with the dual objective of: i) reducing the inlet concentration of the odourous contaminants (in this case, hydrogen sulphide, toluene and p-xylene); ii) capturing and converting the carbon dioxide emissions produced by the degradation process into exploitable algal biomass. The first reactor promoted the degradation of chemical compounds up to 99.57% for an inlet load (IL) of 22.97 g m-3 d-1 while the second allowed the capture of the CO2 resulting from the degradation of gaseous compounds, with biofixation rate up to 81.55%. The absorbed CO2 was converted in valuable feedstocks, with a maximum algal biomass productivity in aPBR of 0.22 g L-1 d-1. Dairy wastewater has been used as alternative nutrient source for both reactors, with a view of reusing wastewater while cultivating biomass, framing the proposed technology in a context of a biorefinery within a circular economy perspective. The biomass produced in the algal photobioreactor was indeed characterized by a high lipid content, with a maximum percentage of lipids per dry weight biomass of 35%. The biomass can therefore be exploited for the production of alternative and clean energy carrier. The proposed biotechnology represents an effective tool for shifiting the conventional plants in carbon neutral platform for implementing principles of ecological transition while achieving high levels of environmental protection.

Dynamics of CO2, CH4, and N2O in Ria Formosa coastal lagoon (southwestern Iberia) and export to the Gulf of Cadiz

A first characterization of greenhouse gases had been carried out to study their role and impact in a productive transitional coastal system of the southern Portugal - Ria Formosa lagoon. To this purpose, the partial pressure of CO2 (pCO2) and the concentration of dissolved CH4 and N2O have been measured. Two surveys were carried out during 2020, at low tide under typical conditions of Spring (March) and end of Summer (October). The samplings sites were distributed along the costal lagoon covering: i) inner areas with strong human impact (influence of different flows of treated wastewater discharges); and ii) main channels in connection with the main inlets to study the exchanges with the ocean. In general, the highest values of the three greenhouse gases were found at the inner studied areas, especially affected by the disposal of treated effluents from wastewater treatment plans, in October. The mean water - atmosphere fluxes of the CO2, CH4 and N2O are positive, showing that the study area acts as a source of these gases to the atmosphere. On the other hand, it was calculated a rough estimation of the three gases globally exported from Ria Formosa to the ocean, through the main six inlets to evaluate the magnitude of the supply of these gases from Ria Formosa to the adjacent ocean. The mean CO2, CH4 and N2O horizontal water fluxes exported from all the inlets of Ria Formosa to the Gulf of Cadiz for both seasons, during low water, are 8.7 ± 3.9 mmol m-2 s-1, 8.0 ± 3.5 μmol m-2 s-1 and 3.2 ± 1.5 μmol m-2 s-1, which corresponds to a mass transport through the inlets section of 0.7 ± 0.7 kg s-1, 0.2 ± 0.2 g s-1 and 0.2 ± 0.3 g s-1 respectively. From these estimates, as expected, the higher mass transport was found at the larger and deeper inlets (Faro-Olhão and Armona).

Greenhouse gas emissions from constructed wetlands: A bibliometric analysis and mini-review

Constructed wetlands (CWs) have been widely applied in wastewater treatment; however, the degradation of organic pollutants within CWs leads to substantial emissions of greenhouse gases (GHGs), such as carbon dioxide, methane and nitrous oxide. Under the low-carbon economy, GHG emissions have emerged as a major concern, and have been intensively studied in the CW field. In this study, we conducted a bibliometric review using CiteSpace and a global-scale analysis of GHG emission levels based on 286 records and proposed potential approaches for the future control of GHG emissions in CWs. We found that the research has generally evolved through three stages over the past 15 years: GHG emission level assessment (2007-2010), mechanisms (2011-2016), and control (2017-2022). The type of CWs is closely related to GHG emissions, with free water surface CWs emitting higher levels of methane and vertical subsurface flow CWs emitting higher levels of carbon dioxide and nitrous oxide. By optimizing CW operation, it is conceivable to synergistically reduce GHG emissions while enhancing pollutant removal.

Biochar production from microalgae: a new sustainable approach to wastewater treatment based on a circular economy

The generation of wastewater due to human activities are the main responsible for environmental problems. These problems are caused by the large amount of organic and inorganic pollutants related to the presence of pesticides, metals, pathogens, drugs and dyes. The photosynthetic treatment of effluents emerges as a sustainable and low-cost alternative for developing wastewater treatment systems based on a circular economy. Chemical compounds present in wastewater can be recovered and reused as a source of nutrients in microalgae cultivation to produce value-added bioproducts. The microalgal biomass produced in the cultivation with effluents has the potential to produce biochar. Biochar is carbon-rich charcoal that can be obtained by converting microalgae biomass through thermal decomposition of organic raw material under limited oxygen supply conditions. Pyrolysis, torrefaction, and hydrothermal carbonization are processes used for biochar synthesis. The application of microalgal biochar as an adsorbent material to remove several compounds present in effluents is an effective and fast treatment. This effectiveness is usually related to the unique physicochemical characteristics of the biochar, such as the presence of functional groups, ion exchange capacity, thermal stability, and high surface area, volume, and pore area. In addition, biochar can be reused in the adsorption process or applied in agriculture for soil correction. In this context, this review article describes the production, characterization, and use of microalgae biochar through a sustainable approach to wastewater treatment, emphasizing its potential in the circular economy. In addition, the article approaches the potential of microalgal biochar as an adsorbent material and its reuse after the adsorption of contaminants, as well as highlights the challenges and future perspectives on this topic.

Advanced treatment of toluene emissions with a cutting-edge algal bacterial photo-bioreactor: Performance assessment in a circular economy perspective

A novel approach for the treatment of VOCs (by using toluene used as a model compound) and the simultaneous conversion of carbon dioxide into valuable biomass has been investigated by using a combination of an activated sludge moving bed bioreactor (MBBR) and an algal photo-bioreactor (PBR). The first unit (MBBR, R1) promoted toluene removal up to 99.9 % for inlet load (IL) of 119.91 g m^-3 d^-1. The CO₂ resulting from the degradation of toluene was then fixed in PBR (R2), with a fixation rate up to 95.8 %. The CO₂ uptake was promoted by algae, with average production of algal biomass in Stage VI of 1.3 g L^-1 d^-1. In the contest of the circular economy, alternative sources of nutrients have been assessed, using synthetic urban wastewater (UWW) and dairy wastewater (DWW) for liquid renewal. The produced biomass with DWW showed a high lipid content, with a maximum productivity of 450.25 mg of lipids L^-1 d^-1. The solution proposed may be thus regarded as a sustainable and profitable strategy for VOCs treatment in a circular economy perspective.

Visual analysis of greenhouse gas emissions from sewage treatment plants based on CiteSpace: from the perspective of bibliometrics

With the global reduction actions of greenhouse gas (GHG) emissions, environmental facilities, including sewage treatment plants (STPs), need to reduce pollutants while minimizing GHG emissions. Therefore, more and more publications revealed the formation mechanism of GHGs in STPs and committed to finding better reduction schemes. From the perspective of bibliometrics, this study used CiteSpace to conduct quantitative and visual analysis based on 1,543 publications retrieved from Web of Science between 2000 and 2021 around the world. We have systematically evaluated the structure, development trend, hot spots, and research frontier in the field of GHG emissions from STPs and compared with the contents of top journals to verify the scientificity of the analysis. The results show that the number of publications has increased year by year, and the networks of authors and institutions show a strong correlation. Among them, the clusters of nitrous oxide, anaerobic digestion, and life cycle assessment (LCA) started earlier and received extensive attention, which derived other clusters in the research process. With the development of the field, researchers have gradually changed from single water treatment facilities to multi-carriers that can realize energy regeneration and utilization simultaneously. Accordingly, the GHG reduction of STPs through energy regeneration and resource recovery has become a hot point and frontier direction, which also challenges the breakthroughs in relevant technologies. Furthermore, it provides scientific support for the formulation of relevant incentive policies and economic subsidy systems, so as to alleviate the pressure of global warming and realize the sustainable development of STPs concurrently.

CO2 in indoor environments: From environmental and health risk to potential renewable carbon source

In the developed world, individuals spend most of their time indoors. Poor Indoor Air Quality (IAQ) has a wide range of effects on human health. The burden of disease associated with indoor air accounts for millions of premature deaths related to exposure to Indoor Air Pollutants (IAPs). Among them, CO₂ is the most common one, and is commonly used as a metric of IAQ. Indoor CO₂ concentrations can be significantly higher than outdoors due to human metabolism and activities. Even in presence of ventilation, controlling the CO₂ concentration below the Indoor Air Guideline Values (IAGVs) is a challenge, and many indoor environments including schools, offices and transportation exceed the recommended value of 1000 ppm_v. This is often accompanied by high concentration of other pollutants, including bio-effluents such as viruses, and the importance of mitigating the transmission of airborne diseases has been highlighted by the COVID-19 pandemic. On the other hand, the relatively high CO₂ concentration of indoor environments presents a thermodynamic advantage for direct air capture (DAC) in comparison to atmospheric CO₂ concentration. This review aims to describe the issues associated with poor IAQ, and to demonstrate the potential of indoor CO₂ DAC to purify indoor air while generating a renewable carbon stream that can replace conventional carbon sources as a building block for chemical production, contributing to the circular economy.

Recent advances and perspectives on production of value-added organic acids through metabolic engineering

Organic acids are important consumable materials with a wide range of applications in the food, biopolymer and chemical industries. The global consumer organic acids market is estimated to increase to $36.86 billion by 2026. Conventionally, organic acids are produced from the chemical catalysis process with petrochemicals as raw materials, which posts severe environmental concerns and conflicts with our sustainable development goals. Most of the commonly used organic acids can be produced from various organisms. As a state-of-the-art technology, large-scale fermentative production of important organic acids with genetically-modified microbes has become an alternative to the chemical route to meet the market demand. Despite the fact that bio-based organic acid production from renewable cheap feedstock provides a viable solution, low productivity has impeded their industrial-scale application. With our deeper understanding of strain genetics, physiology and the availability of strain engineering tools, new technologies including synthetic biology, various metabolic engineering strategies, omics-based system biology tools, and high throughput screening methods are gradually established to bridge our knowledge gap. And they were further applied to modify the cellular reaction networks of potential microbial hosts and improve the strain performance, which facilitated the commercialization of consumable organic acids. Here we present the recent advances of metabolic engineering strategies to improve the production of important organic acids including fumaric acid, citric acid, itaconic acid, adipic acid, muconic acid, and we also discuss the current challenges and future perspectives on how we can develop a cost-efficient, green and sustainable process to produce these important chemicals from low-cost feedstocks.

Enhanced sustainable integration of CO2 utilization and wastewater treatment using microalgae in circular economy concept

Microalgae have been shown to have a promising potential for CO₂ utilization and wastewater treatment which still faces the challenges of high resource and energy requirements. The implementation of the circular economy concept is able to address the issues that limit the application of microalgae-based technologies. In this review, a comprehensive discussion on microalgae-based CO₂ utilization and wastewater treatment was provided, and the integration of this technology with the circular economy concept, for long-term economic and environmental benefits, was described. Furthermore, technological challenges and feasible strategies towards the improvement of microalgae cultivation were discussed. Finally, necessary regulations and effective policies favoring the implementation of microalgae cultivation into the circular economy were proposed. These are discussed to support sustainable development of microalgae-based bioremediation and bioproduction. This work provides new insights into the implementation of the circular economy concept into microalgae-based CO₂ utilization and wastewater treatment to enhance sustainable production.

Thermophilic biological fluidized bed reactor in sludge line reduces greenhouse gas emissions in wastewater treatment system

Greenhouse gas (GHG) emissions represent one of the main drawbacks of wastewater (WW) treatment. However, results of a detailed estimation of the emissions can be a valid tool to define optimal solutions for minimizing impact of WW treatment system on the environment. Thermophilic biological fluidized bed reactor (TBFBR) has been recently proposed as an alternative solution for biological sludge minimization in wastewater treatment plant (WWTPs). In this work, 5 diverse scenarios of sludge line composition were studied and combined with 5 diverse sludge disposal options. GHG emissions in 25 combinations were fully investigated to define optimal sludge treatment and disposal option. Results suggested that TBFBR help to reduce net emitted GHGs with respect to scenario with conventional stabilization treatment in sludge line (anaerobic digestion) (-32.3 ± 3.55 %) thanks to (i) the reuse in water line of the aqueous residue of TBFBR as alternative carbon source, (ii) the significant minimization of sludge production, and (iii) the contained impact of gross GHG emissions due to the energy consumption of this process. The strong minimization of sludge also led to a decisive reduction in GHG emissions in the subsequent phases of transport, additional treatments, and final disposal making the choice of the disposal option indifferent on the overall GHG emission estimation. Moreover, the coupling of processes for the simultaneous and preventive maximization of energy recovery (TCH, and AnaD) before sludge minimization in TBFBR determined a limited reduction of GHG emission compared to scenario with TBFBR alone (-3.71 ± 1.47 %).

Systematic data-driven exploration of Austrian wastewater and sludge treatment - implications for phosphorus governance, costs and environment

Within the new policy framework shaped by the EU Green Deal and the Circular Economy Action Plans, the field of wastewater and sludge treatment in Europe is subject to high expectations and new challenges related to mitigation of greenhouse gas emissions, micropollutant removal and resource recovery. With respect to phosphorus recovery, several technologies and processes have been thoroughly investigated. Nevertheless, a systemic and detailed understanding of the existing infrastructure and of the related environmental and economic implications is missing. Such basis is essential to avoid unwanted consequences in designing new strategies, given the long lifespan of any infrastructural change. This study couples a newly collected and highly detailed database for all wastewater treatment plants in Austria bigger than 2000 population equivalent with a combination of analyses, namely Substance Flow Analysis with focus on nutrient and metal distribution in different environmental and anthropogenic compartments, Energy Flow Analysis, Life Cycle Assessment and cost estimation. The case study of Austria is of special interest, given its highly autonomous administration in federal states and its contrasting traits, ranging from flat metropolitan areas like Vienna to low-populated alpine areas. The significant impact of electricity demand of wastewater treatment on the overall Cumulative Energy Demand (CED) shows the importance of optimization measures. Further, the current system of wastewater and sludge disposal have a low efficiency in recovering nutrients and in directing pollutants as heavy metals into final sinks. Sludge composting with subsequent use in landscaping does not only show an unfavorable environmental balance, but it is the only relevant route leading to additional CED and Global Warming Potential emissions and to the highest transport volume. Altogether, the outcomes of this study provide a sound basis to further develop national strategies for resource recovery aimed to optimize trade-offs between different economic and environmental objectives.

Prospects and trends in bioelectrochemical systems: Transitioning from CO2 towards a low-carbon circular bioeconomy

Resource scarcity and climate change are the most quested topics in view of environmental sustainability. CO2 sequestration through bioelectrochemical systems is an attractive option for fostering bioeconomy development upon several value-added products generation. This review details the state-of-the-art of bioelectrochemical systems for resource recovery from CO2 along with various biocatalysts capable of utilizing CO2. Two bioprocesses (photo-electrosynthesis and chemolithoelectrosynthesis) were discussed projecting their potential for biobased economy development from CO2. Significance of adopting circular strategies for efficient resource recycling, intensifying product value, integrations/interlinking of multiple process chains for the development of circular bioeconomy were discussed. Existing constrains as well as outlook for near establishment of circular bioeconomy from CO2 is presented by weighing fore-sighted plans with current actions. Need for developing CO2-based circular bioeconomy via innovative business models by analyzing social, technical, environmental and product related aspects are also discussed providing a roadmap of gaps to pursue for attaining practicality.

Centrate as a sustainable growth medium: Impact on microalgal inocula and bacterial communities in tubular photobioreactor cultivation systems

Centrate is a low-cost alternative to synthetic fertilizers for microalgal cultivation, reducing environmental burdens and remediation costs. Adapted microalgae need to be selected and characterised to maximise biomass production and depuration efficiency. Here, the performance and composition of six microalgal communities cultivated both on synthetic media and centrate within semi-open tubular photobioreactors were investigated through Illumina sequencing. Biomass grown on centrate, exposed to a high concentration of ammonium, showed a higher quantity of nitrogen (5.6% dry weight) than the biomass grown on the synthetic media nitrate (3.9% dry weight). Eukaryotic inocula were replaced by other microalgae while cyanobacterial inocula were maintained. Communities were generally similar for the same inoculum between media, however, inoculation with cyanobacteria led to variability within the eukaryotic community. Where communities differed, centrate resulted in a higher richness and diversity. The higher nitrogen of centrate possibly led to higher abundance of genes coding for N metabolism enzymes.

Knowledge Atlas on the Relationship between Water Management and Constructed Wetlands—A Bibliometric Analysis Based on CiteSpace

Water management is a crucial resource conservation challenge that mankind faces, and encouraging the creation of manmade wetlands with the goal of achieving long-term water management is the key to long-term urban development. To summarise and analyse the status of the research on the relationship between water management and constructed wetlands, this paper makes use of the advantages of the bibliometric visualization of CiteSpace to generate country/region maps and author-collaboration maps, and to analyse research hotspots and research dynamics by using keywords and literature co-citations based on 1248 pieces of related literature in the core collection in the Web of Science (WoS) database. The existing research shows that the research content and methods in the field of constructed-wetland and water-management research are constantly being enriched and deepened, including the research methods frequently used in constructed wetlands in water management and in the research content under concern, the functions and roles of constructed wetlands, the relevant measurement indicators of the purification impact of constructed wetlands on water bodies, and the types of water bodies treated by constructed wetlands in water management. We summarise the impact pathways of constructed wetlands on water management, as well as the impact factors of constructed wetlands under water-management objectives, by analysing the future concerns in the research field to provide references for research.

Degradation of gaseous volatile organic compounds (VOCs) by a novel UV-ozone technology

In this study, a UV-assisted ozonation (UV/O₃) process for the degradation of VOCs emissions with a final scrubbing phase was implemented to evaluate the removal efficiency of toluene and to prevent the release of polluting intermediates of the single-step process. Inlet toluene concentration and applied voltage were varied in order to investigate several operating conditions. The results highlighted that at higher inlet concentration the abatement of toluene was lower, while increase in ozone concentration led to an increase of the degradation efficiencies. The additional water scrubbing step enhanced the abatement of UV/O₃ up to 98.5%, due to the solubilisation of ozone and by-products in the process water and, thus, the further oxidation of the contaminants within this phase. A maximum Elimination Capacity (EC_max) of 22.6 g m⁻³ h⁻¹ was achieved with the UV/O₃ + Scrubbing. The combined system boosted higher performance and stability compared to the stand-alone (UV/O₃) process along with a more economical and environmental sustainability.

Circular Economy Framework for Energy Recovery in Phytoremediation of Domestic Wastewater

Circular economy (CE) strategy is crucial in developing towards sustainable growth. It was created to promote resource utilization and the elimination of waste production. This article aimed to study the possibilities of using the CE framework in wastewater bioremediation and energy recovery using hydroponic tanks. The integration of phytoremediation with bioenergy, construction and lifespan of hydroponic tanks in phytoremediation of wastewater, selection of aquatic plants and the expected challenges in the implementation of CE in phytoremediation of wastewater were discussed. The plant-based biomass harvested and the relative growth rate (RGR) of the selected plants from the phytoremediation process was evaluated. The findings obtained indicated that the selected plants tripled in weight after 14 days cultivation period at different retention times. E. crassipes recorded the highest growth with 2.5 ± 0.03 g g−1 d−1, followed by S. molesta with 1.33 ± 0.05 g g−1 d−1 and then P. stratiotes recorded 0.92 ± 0.27 g g−1 d−1 at the end of the cultivation period. Therefore, the selected plants have been identified as having the potential to be used in phytoremediation as well as a source of energy production. The outcome of our review suggested the adoption of a lifecycle assessment as the CE framework for the phytoremediation of wastewater.

Comprehensive evaluation of the carbon footprint components of wastewater treatment plants located in the Baltic Sea region

Finland and Poland share similar environmental interests with regard to their wastewater effluents eventually being discharged to the Baltic Sea. However, differences in the influent wastewater characteristics, treatment processes, operational conditions, and carbon intensities of energy mixes in both countries make these two countries interesting for carbon footprint (CF) comparison. This study aimed at proposing a functional unit (FU) which enables a comprehensive comparison of wastewater treatment plants (WWTPs) in terms of their CF. Direct emissions had the highest contribution (70%) to the total CF. Energy consumption dominated the total indirect emissions in both countries by over 30%. Polish WWTPs benefitted more from energy self-sufficiency than Finnish plants as a result of higher electricity emission factors in Poland. The main difference between indirect emissions of both countries were attributed to higher chemical consumption of the Finnish WWTPs. Total pollution equivalent removed (TPE_rem) FU proposed enabled a better comparison of WWTPs located in different countries in terms of their total CF. High correlations of TPE_rem with other FUs were found since TPE_rem could balance out the differences in the removal efficiencies of various pollutants. Offsetting CF was found a proper strategy for the studied WWTPs to move towards low-carbon operation. The studied WWTPs could reduce their CF from up to 27% by different practices, such as selling biofuel, electricity and fertilizers. These findings are applicable widely since the selected WWTPs represent the typical treatment solutions in Poland, Finland and in the Baltic Sea region.

Algae biotechnology for industrial wastewater treatment, bioenergy production, and high-value bioproducts

A growing world population is causing hazardous compounds to form at an increasingly rapid rate, calling for ecological action. Wastewater management and treatment is an expensive process that requires appropriate integration technology to make it more feasible and cost-effective. Algae are of great interest as potential feedstocks for various applications, including environmental sustainability, biofuel production, and the manufacture of high-value bioproducts. Bioremediation with microalgae is a potential approach to reduce wastewater pollution. The need for effective nutrient recovery, greenhouse gas reduction, wastewater treatment, and biomass reuse has led to a wide interest in the use of microalgae for wastewater treatment. Furthermore, algae biomass can be used to produce bioenergy and high-value bioproducts. The use of microalgae as medicine (production of bioactive and medicinal compounds), biofuels, biofertilizers, and food additives has been explored by researchers around the world. Technological and economic barriers currently prevent the commercial use of algae, and optimal downstream processes are needed to reduce production costs. Therefore, the simultaneous use of microalgae for wastewater treatment and biofuel production could be an economical approach to address these issues. This article provides an overview of algae and their application in bioremediation, bioenergy production, and bioactive compound production. It also highlights the current problems and opportunities in the algae-based sector, which has recently become quite promising.

Innovative encapsulated self-forming dynamic bio-membrane bioreactor (ESFDMBR) for efficient wastewater treatment and fouling control

The concept of a novel living encapsulated self-forming dynamic bio-membranes (ESFDM) for an innovative wastewater treatment in membrane bioreactor (MBR) is presented in the current study. The active filtering membrane is encapsulated, and thus stabilized, between two support meshes with pore in micrometer size. The combination of activated sludge, the ESFDM and the cake layer formed external to the filtering module contributed to the treatment of municipal wastewater. COD concentration reductions (average value of 95.55 ± 1.44%) by ESFDM bioreactor (ESFDMBR) were comparable to those obtained with a previously reported membrane bioreactor (MBR), where a conventional membrane was studied under the same operating conditions. The ESFDMBR, compared to the conventional MBR, obtained higher reductions of NH₃-N, NO₃^-N and PO₄^3-P concentrations. Increased removals of nitrogen-containing nutrients were ascribed to anoxic conditions reached in the ESFDM layer protected from the aeration by the external cake layer. Rate of increase of transmembrane pressure (TMP) per day in the ESFDMBR (0.03 kPa/day) was lower than the value obtained in the previously reported conventional MBR (8.08 kPa/day). Lower concentrations of fouling precursors in combination with the effective filtration capacity of the porous living ESFDM resulted in the reduction of the fouling rate. Analysis of microbiological community revealed that the microbial community structures in the mixed liquor and ESFDM were different. The ESFDM layer promoted growth of bacteria as indicated by the higher total cell count and higher microbial diversity compared to those observed in the mixed liquor.

Full-Scale Odor Abatement Technologies in Wastewater Treatment Plants (WWTPs): A Review

The release of air pollutants from the operation of wastewater treatment plants (WWTPs) is often a cause of odor annoyance for the people living in the surrounding area. Odors have been indeed recently classified as atmospheric pollutants and are the main cause of complaints to local authorities. In this context, the implementation of effective treatment solutions is of key importance for urban water cycle management. This work presents a critical review of the state of the art of odor treatment technologies (OTTs) applied in full-scale WWTPs to address this issue. An overview of these technologies is given by discussing their strengths and weaknesses. A sensitivity analysis is presented, by considering land requirements, operational parameters and efficiencies, based on data of full-scale applications. The investment and operating costs have been reviewed with reference to the different OTTs. Biofilters and biotrickling filters represent the two most applied technologies for odor abatement at full-scale plants, due to lower costs and high removal efficiencies. An analysis of the odors emitted by the different wastewater treatment units is reported, with the aim of identifying the principal odor sources. Innovative and sustainable technologies are also presented and discussed, evaluating their potential for full-scale applicability.

Factors for Implementation of Circular Economy in Firms in COVID-19 Pandemic Times: The Case of Peru

The circular economy can contribute to the eco-efficient use of resources. Firms can obtain relevant benefits if they implement a circular economy. In Peru, the circular economy would create benefits, but it is not fully clear what factors explain the acceptance of firms of implementing a circular economy. Following the theory of planned behavior, the current research assesses the influence of attitudes, subjective norms, perceived behavioral norms, intentions, and pressures on behaviors towards the circular economy. A total of 71 medium-size firms based in Peru participated in an online survey. Six questions were focused on general information, and forty-seven questions evaluated the circular economy behavior of firms. A partial least square structural equation modeling technical analysis was used. It was found that attitudes (0.144), subjective norms (0.133), and perceived behavioral control (0.578) had a positive influence on intentions; also, perceived behavioral control (0.461) had a positive influence on behaviors towards the circular economy. Finally, pressures had a positive influence (0.162) on behaviors towards the circular economy. The model explained 64.3% of the behaviors towards the circular economy. The outcomes of the bootstrapping test were used to evaluate if the path coefficients are significant. This study showed that attitudes, subjective norms, perceived behavioral norms, intentions, and pressures explained circular economy behaviors. This information can help firms develop strategies to move forward a circular economy and provide governments information about the current situation of circular economy implementation to generate new norms and strategies for more implementation of circular economy measures in enterprises. The novelty is based on using the PLS-SEM technique.

One planet, one health, one future: The environmental perspective

The final goal of the "One Health" is the control of the global health of our planet with a multidisciplinary approach that involves knowledge for different disciplines. In the near future, we could see in the same team veterinarians, doctors, and environmental experts work together to guarantee the health of our planet and one sustainable future for all.