Electrochemical oxidation metronidazole with Co modified PbO2 electrode: Degradation and mechanism

A comparative review on the mitigation of metronidazole residues in aqueous media using various physico-chemical technologies

In the last few decades, pharmaceuticals have emerged as a new class of serious environmental pollutants. The presence of these emerging contaminants even in minimal amounts (micro- to nanograms) has side effects, and they can cause chronic toxicity to health and the environment. Furthermore, the presence of pharmaceutical contaminants in water resources leads to significant antibiotic resistance in bacteria. Hence, the removal of antibiotics from water resources is essential. Thus far, a wide range of methods, including adsorption, photodegradation, oxidation, photolysis, micro-/nanofiltration, and reverse osmosis, has been used to remove pharmaceutical contaminants from water systems. In this article, research related to the processes for the removal of metronidazole antibiotics from water and wastewater, including adsorption (carbon nanotubes (CNTs), magnetic nanocomposites, magnetic molecularly imprinted polymer (MMIP), and metal-organic frameworks), filtration, advanced oxidation processes (photocatalytic process, electrochemical advanced oxidation processes, sonolysis and sonocatalysis) and aqueous two-phase systems (ATPSs), was reviewed. Results reveal that advanced oxidation processes, especially photocatalytic and sonolysis processes, have high potential in removing MNZ (more than 90%).

Electrochemical chlorine evolution reaction to improve the desalination of sea sand

Sea sand, a vital sand and gravel resource, is rich in chloride, which causes corrosion of steel reinforcements. This study investigates the effect of the electrochemical chlorine evolution reaction (CER) on the desalination of sea sand. The results indicate that the chlorine removal efficiency (RE) of sea sand increased from 48.76 to 56.40 % under optimal conditions: a current density of 15 mA/cm2, an electrolysis time of 1 min, and a sodium sulphate-supported electrolyte concentration of 0.05 mol/L. After 30 days of resting, the dissolved chlorine content in sea sand was 0.154 %, which was 21.03 % lower than that of the control group. The electrically active chlorine-mediated desalination process demonstrated excellent dechlorination ability, facilitated the transformation of metal and organic chlorine into liquid and gaseous forms, and reduced the slow release of chloride from sea sand. Therefore, CER is expected to be an efficient method for sea sand desalination.

Ultrasonic treatment of endocrine disrupting compounds, pharmaceuticals, and personal care products in water: An updated review

Pharmaceuticals, personal care products (PPCPs), and endocrine-disrupting compounds (EDCs) have seen a recent sustained increase in usage, leading to increasing discharge and accumulation in wastewater. Conventional water treatment and disinfection processes are somewhat limited in effectively addressing this micropollutant issue. Ultrasonication (US), which serves as an advanced oxidation process, is based on the principle of ultrasound irradiation, exposing water to high-frequency waves, inducing thermal decomposition of H2O while using the produced radicals to oxidize and break down dissolved contaminants. This review evaluates research over the past five years on US-based technologies for the effective degradation of EDCs and PPCPs in water and assesses various factors that can influence the removal rate: solution pH, temperature of water, presence of background common ions, natural organic matter, species that serve as promoters and scavengers, and variations in US conditions (e.g., frequency, power density, and reaction type). This review also discusses various types of carbon/non-carbon catalysts, O3 and ultraviolet processes that can further enhance the degradation efficiency of EDCs and PPCPs in combination with US processes. Furthermore, numerous types of EDCs and PPCPs and recent research trends for these organic contaminants are considered.

The electrocatalytic degradation of 1,4-dioxane by Co-Bi/GAC particle electrode

Efficient degradation of industrial organic wastewater has become a significant environmental concern. Electrochemical oxidation technology is promising due to its high catalytic degradation ability. In this study, Co-Bi/GAC particle electrodes were prepared and characterized for degradation of 1,4-dioxane. The electrochemical process parameters were optimized by response surface methodology (RSM), and the influence of water quality factors on the removal rate of 1,4-dioxane was investigated. The results showed that the main influencing factors were the Co/Bi mass ratio and calcination temperature. The carrier metals, Co and Bi, existed mainly on the GAC surface as Co3O4 and Bi2O3. The removal of 1,4-dioxane was predominantly achieved through the synergistic reaction of electrode adsorption, anodic oxidation, and particle electrode oxidation, with ·OH playing a significant role as the main active free radical. Furthermore, the particle electrode was demonstrated in different acid-base conditions (pH = 3, 5, 7, 9, and 11). However, high concentrations of Cl- and NO3- hindered the degradation process, potentially participating in competitive reactions. Despite this, the particle electrode exhibited good stability after five cycles. The results provide a new perspective for constructing efficient and stable three-dimensional (3D) electrocatalytic particle electrodes to remove complex industrial wastewater.

Removal of N-nitrosopyrrolidine from GAC by a three-dimensional electrochemical reactor: degradation mechanism and degradation path

Nitrogen-containing disinfection by-products (N-DBPs) produced in the process of drinking water disinfection are widely concerning due to the high cytotoxicity and genotoxicity. It is due to the difficulty of natural degradation of N-DBPs in water and the fact that conventional treatment systems do not effectively treat N-DBPs in drinking water. In this study, N-nitrosopyrrolidine (NPYR) in water was electrocatalytically degraded by a three-dimensional electrode reactor (3DER). This system applied graphite plates as anode and cathode. The granular activated carbon (GAC) was used as third electrode. The degradation of NPYR using a continuous flow three-dimensional electrode reactor was investigated by examining the effects of flow rate, current density, electrolyte concentration, and pollutant concentration on the degradation efficiency, energy consumption, and reaction kinetics of GAC particle electrodes. The results showed that the optimal operating conditions were flow rate = 0.45 mL/min, current density = 6 mA/cm2, Na2SO4 concentration = 0.28 mol/L, and NPYR concentration = 20 mg/L. Under optimal conditions, the degradation of NPYR exceeded 58.84%. The main contributor of indirect oxidation was deduced from free radical quenching experiments. NPYR concentration was measured by GC-MS with DB-5 capillary column, operating in full scan monitoring mode for appropriate quantification of NPYR and intermediates. Based on the identification of reaction intermediates, a possible pathway for the electrochemical oxidation of NPYR on GAC particle electrodes was proposed.

Robust PbO2 modified by co-deposition of ZrO2 nanoparticles for efficient degradation of ceftriaxone sodium

In recent years, PbO2 electrodes have received widespread attention due to their high oxygen evolution reaction (OER) activity. However, due to the brittle nature of the plating layer, it is easy to cause the active layer to fall off. Pb2+ will leach out with the electrochemical process causing secondary pollution. The starting point of this study is established to improve the stability and adhesion of the electrode coating. Electrochemical oxidation technology has the characteristics of high treatment efficiency, wide range of applications, and non-polluting environment. In this study, conventional PbO2 electrodes were modified by using co-deposition of ZrO2 nanoparticles. In addition, α-PbO2 was added to increase the stability of the electrodes. At a high current density of 1 A/cm2, the accelerated life of the pure PbO2 electrode is 648 h, the accelerated life of the PbO2-ZrO2 electrode is 1.37 times that of the pure PbO2, and the electrode with an added α-PbO2 layer is 1.69 times that of the pure PbO2 electrode. The amount of dissolved Pb2+ was only 29% of that of pure PbO2. The electrochemical performance of the electrode is evaluated by studying the degradation effect of ceftriaxone sodium (CXM). The addition of ZrO2 nanoparticles alters the particle size and deposition content of PbO2, leading to a unique crystal structure distinct from pure PbO2. Compared to conventional PbO2 electrodes, the PbO2-ZrO2 can remove chemical oxygen demand (COD) and pollutants more efficiently, removing for 59% increased by 38.47%. Therefore, PbO2-ZrO2 is of great value in the field of electrochemical degradation of industrial pollutants.

Bimetal-oxide (Fe/Co) modified bagasse-waste carbon coated on lead oxide-battery electrode for metronidazole removal

Current study covers the preparation and application of a commercial modified lead oxide battery electrode (LBE) in electrochemical oxidation (ECO) of metronidazole (MNZ) in an aqueous phase. Modified electrode is prepared by doping of bimetal-oxide (Fe and Zn) nanoparticles (NPs) & single metal-oxide (Fe/Zn) on bagasse-waste carbon (bwc) which is further coated on LBE. The modified LBE electrode surface was examined for metal-oxide NPs through X-ray diffraction analysis (XRD). Different electrodes are prepared by varying combinations of two metal-oxide based on molar ratio and tested for electrochemical characterization and MNZ removal test. Based on large oxygen evolution potential in a linear sweep volumetry (LSV) analysis and high MNZ removal rate, the best electrode has been represented as Fe1:Co2-bwc/LBE which contains Fe & Co molar ratio of 1:2. Moreover, equilibrium attained at faster rate in degradation process of MNZ, where pseudo first order kinetics of 2.29 × 10-2 min-1 was obtained under optimized condition of (MNZ:100 mg/L, pH:7, CD: 30 mA/cm2 and electrolyte: 0.05 M Na2SO4). Maximum MNZ removal, total organic carbon removal (TOC), mineralization current efficiency (MCE) & energy consumption (EC) of 98.7%, 85.3%, 62.2% & 96.143 kW h/kg-TOC removed are found in 180 min of treatment time for Fe1:Co2-bwc/LBE electrode. Accelerated service life test confirms that the stability of modified electrode is enhanced by 1.5 times compared to pristine LBE. Repeatability test confirms that modified LBE (Fe1:Co2-bwc/LBE) can be utilized up to 3 times.

Development of SDS-Modified PbO2 Anode Material Based on Ti3+ Self-Doping Black TiO2NTs Substrate as a Conductive Interlayer for Enhanced Electrocatalytic Oxidation of Methylene Blue

Efficient and stable electrode materials are urgently required for wastewater treatment in the electrocatalytic degradation of toxic and refractory organic pollutants. Ti3+ self-doping black TiO2 nanotube arrays (Ti/B-TiO2-NTs) as an interlayer were used for preparing a novel PbO2 electrode via an electrochemical reduction technology, and a sodium dodecyl sulfate (SDS)-modified PbO2 catalytic layer was successfully achieved via an electrochemical deposition technology. The physicochemical characterization tests showed that the Ti/B-TiO2-NTs/PbO2-SDS electrodes have a denser surface and finer grain size with the introduction of Ti3+ in the interlayer of Ti/TiO2-NTs and the addition of SDS in the active layer of PbO2. The electrochemical characterization results showed that the Ti3+ self-doping black Ti/TiO2-NTs/PbO2-SDS electrode had higher oxygen evolution potential (2.11 V vs. SCE), higher electrode stability, smaller charge-transfer resistance (6.74 Ω cm-2), and higher hydroxyl radical production activity, leading to it possessing better electrocatalytic properties. The above results indicated that the physicochemical and electrochemical characterization of the PbO2 electrode were all enhanced significantly with the introduction of Ti3+ and SDS. Furthermore, the Ti/B-TiO2-NTs/PbO2-SDS electrodes displayed the best performance on the degradation of methylene blue (MB) in simulated wastewater via bulk electrolysis. The removal efficiency of MB and the chemical oxygen demand (COD) could reach about 99.7% and 80.6% under the optimal conditions after 120 min, respectively. The pseudo-first-order kinetic constant of the Ti/B-TiO2-NTs/PbO2-SDS electrode was 0.03956 min-1, which was approximately 3.18 times faster than that of the Ti/TiO2-NTs/PbO2 electrode (0.01254 min-1). In addition, the Ti/B-TiO2-NTs/PbO2-SDS electrodes showed excellent stability and reusability. The degradation mechanism of MB was explored via the experimental identification of intermediates. In summary, the Ti3+ self-doping black Ti/TiO2-NTs/PbO2-SDS electrode is a promising electrode in treating wastewater.

Catalytic electrodes' characterization study serving polluted water treatment: environmental healthcare and ecological risk assessment

Pesticide residues in the environment have irreparable effects on human health and other organisms. Hence, it is necessary to treat and degrade them from polluted water. In the current work, the electrochemical removal of the fenitrothion (FT), trifluralin (TF), and chlorothalonil (CT) pesticides were performed by catalytic electrode. The characteristics of SnO2-Sb2O3, PbO2, and Bi-PbO2 electrodes were described by FE-SEM and XRD. Dynamic electrochemical techniques including cyclic voltammetry, electrochemical impedance spectroscopy, accelerated life, and linear polarization were employed to investigate the electrochemical performance of fabricated electrodes. Moreover, evaluate the risk of toxic metals release from the catalytic electrode during treatment process was investigated. The maximum degradation efficiency of 99.8, 100, and 100% for FT, TF, and CT was found under the optimal condition of FT, TF, and CT concentration 15.0 mg L-1, pH 7.0, current density 7.0 mA cm-2, and electrolysis time of 120 min. The Bi-PbO2, PbO2, and SnO2-Sb2O3 electrodes revealed the oxygen evolution potential of 2.089, 1.983, 1.914 V, and the service lifetime of 82, 144, and 323 h, respectively. The results showed that after 5.0 h of electrolysis, none of the heavy metals such as Bi, Pb, Sb, Sn, and Ti were detected in the treated solution.

Decolorization, COD and turbidity removal of the raw vinasse effluent by a one-step electro-oxidation process on a Pb/PbO2 anode

In this research, and for the first time, the application of anode Pb/PbO2 (prepared from combined thermal oxidation and electrochemical oxidation method) and steel cathode in a flow sample electrochemical treatment process of vinasse and in the wastewater of alcohol factories, has been investigated. The combination of electrodes of Pb/PbO2 as an anode, steel, and/or graphite as a cathode was used in the proposed electrochemical treatment setup. The efficiency of the proposed electrochemical treatment was determined by the removal percentage of chemical oxygen demand (COD), turbidity and color of vinasse samples. The response surface method (RSM) by Minitab 18 was used to determine the effect of the studied factors as well as to detect the relationship between variables. The results showed that under optimum conditions (Pb/PbO2 electrode as the anode and steel electrode as the cathode, a voltage of 30 V, pH 6.5, and reaction time of 45 min), the percentage reduction values of COD, turbidity and color were 97.7, 77.3 and 92.7%, respectively.

Effects of oxygen pressure on the morphology and surface energetics of β-PbO2: insight from DFT calculations

For over a century, lead dioxide (PbO₂) has been investigated in lead-acid batteries and extensively utilized in a variety of applications. Identifying the surface properties and equilibrium morphology of β-PbO₂ (rutile phase) particles is mandatory for industrial utilization and surface engineering. Using density-functional calculations within the generalized gradient approximation revised for solids (PBEsol), we investigate a variety of surface properties of β-PbO₂. The surface energies of low-Miller-index stoichiometric surfaces are firstly determined, and the (110) surface is found to be the most thermodynamically stable. The relative energetics of these surfaces are represented by a Wulff construction which shows an acicular shape, mostly dominated by the (110) and (100) surfaces. Besides, we investigate the surface chemistry of β-PbO₂ under reduction and oxidation conditions as a function of oxygen pressure, finding that most surfaces except for (100) and (110) are likely to be oxidized. Under oxygen pressure at 1 atm and oxygen-rich limit, the (101) surface is the most thermodynamically stable, dominating the Wulff construction with pyramidal shapes. Our results indicate that the growth conditions that cause non-stoichiometry of the surface could modify the equilibrium Wulff shape of β-PbO₂. Our predicted Wulff shapes and dominant facets agree with the experimental results in which the pyramidal shape of the β-PbO₂ grains has often been observed with the (101) preferred orientation.

PbO2 materials for electrochemical environmental engineering: A review on synthesis and applications

Lead dioxide (PbO₂) materials have been widely employed in various fields such as batteries, electrochemical engineering, and more recently environmental engineering as anode materials, due to their unique physicochemical properties. Key performances of PbO₂ electrodes, such as energy efficiency and space-time yield, are influenced by morphological as well as compositional factors. Micro-nano structure regulation and decoration of metal/non-metal on PbO₂ is an outstanding technique to revamp its electrocatalytic activities and enhance environmental engineering efficiency. The aim of this review is to comprehensively summarize the recent research progress in the morphology control, the structure constructions, and the element doping of PbO₂ materials, further with many environmental application cases evaluated. Concerning electrochemical environmental engineering, the lead dioxide employed in chemical oxygen demand detection, ozone generators, and wastewater treatment has been comprehensively reviewed. In addition, the future research perspectives, challenges and the opportunities on PbO₂ materials for environmental applications are proposed.

Elaboration of Highly Modified Stainless Steel/Lead Dioxide Anodes for Enhanced Electrochemical Degradation of Ampicillin in Water

Lead dioxide-based electrodes have shown a great performance in the electrochemical treatment of organic wastewater. In the present study, modified PbO2 anodes supported on stainless steel (SS) with a titanium oxide interlayer such as SS/TiO2/PbO2 and SS/TiO2/PbO2-10% Boron (B) were prepared by the sol–gel spin-coating technique. The morphological and structural properties of the prepared electrodes were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS). It was found that the SS/TiO2/PbO2-10% B anode led to a rougher active surface, larger specific surface area, and therefore stronger ability to generate powerful oxidizing agents. The electrochemical impedance spectroscopy (EIS) measurements showed that the modified PbO2 anodes displayed a lower charge transfer resistance Rct. The influence of the introduction of a TiO2 intermediate layer and the boron doping of a PbO2 active surface layer on the electrochemical degradation of ampicillin (AMP) antibiotic have been investigated by chemical oxygen demand measurements and HPLC analysis. Although HPLC analysis showed that the degradation process of AMP with SS/PbO2 was slightly faster than the modified PbO2 anodes, the results revealed that SS/TiO2/PbO2-10%B was the most efficient and economical anode toward the pollutant degradation due to its physico-chemical properties. At the end of the electrolysis, the chemical oxygen demand (COD), the average current efficiency (ACE) and the energy consumption (EC) reached, respectively, 69.23%, 60.30% and 0.056 kWh (g COD)−1, making SS/TiO2/PbO2-10%B a promising anode for the degradation of ampicillin antibiotic in aqueous solutions.

Synergistic mechanism of supported Mn-Ce oxide in catalytic ozonation of nitrofurazone wastewater

In this study, the catalytic materials of MnO_x/γ-Al₂O₃, CeO₂/γ-Al₂O₃, and Mn_xCe_1-xO₂/γ-Al₂O₃ for catalytic ozonation were synthesized. The catalysts were used in heterogeneous catalytic ozonation of the wastewater containing ntrofurazone (NFZ). The effects of the catalytic ozonation operational factors were systematically evaluated in terms of ozone dosing, catalyst dosing, initial NFZ concentration, and pH. The results showed that the catalytic activity of the Mn_xCe_1-xO₂/γ-Al₂O₃ was higher than that of the MnO_x/γ-Al₂O₃ and CeO₂/γ-Al₂O₃. The kinetics analysis revealed that bimetallic loading has a synergistic effect and the mechanism of this effect was investigated in the catalytic ozonation system. The catalysts were characterized by FESEM, EDS, XRD, XPS, IR, and BET. The characteristics of the catalysts revealed that Mn could alter the oxide species on the metal surface and interfere with the formation of CeO₂ crystals, which led to smaller grains, enhanced adsorption oxygen, and greater specific surface area. The Mn_xCe_1-xO₂/γ-Al₂O₃ crystals could form a solid solution, which helps higher catalytic activity. This study adds to the understanding of the synergistic mechanism of the loaded Ce-Mn oxide catalysts in the heterogeneous catalytic ozonation system and provides a feasible method for degrading pharmaceutical wastewater.

Blue TiO2 nanotube electrocatalytic membrane electrode for efficient electrochemical degradation of organic pollutants

In this study, a Ti³⁺-doped TiO₂ porous membrane (Blue TiO₂/Ti) was fabricated and employed for electrochemical degradation of organic pollutants in the single-pass flow-through mode. Characterizations including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microcopy (SEM) and energy dispersive spectroscopy (EDS) verified that Ti³⁺-doped anatase TiO₂ with nanotube structures was successfully prepared. Electrochemical analysis including linear sweep voltammetry (LSV), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and electrochemical active surface area (ESA) revealed higher oxygen evolution potential (OEP, 2.23 V vs. Ag/AgCl), larger redox peak current, lower impedance and larger ESA (69 cm²/cm²) of Blue TiO₂/Ti compared to the Ti and TiO₂/Ti membranes. The effects of current density, flow rate and solution environment on the removal of methylene blue (MB) were investigated. The removal rates of various organic pollutants including sulfamethoxazole (SMX), methyl orange (MO), bisphenol A (BPA) and MB could reach 92.2%-99.5%. The quenching experiment proved that hydroxyl radicals (•OH) played the major role in the Blue TiO₂/Ti based electrochemical system. Furthermore, the degradation pathways of two typical pollutants (SMX and MB) were proposed by analyzing the oxidation products with liquid chromatography-mass spectrometry (LC-MS) and gas chromatography-mass spectrometry (GC-MS), with the assistance of orbital-weighted Fukui index (f_w⁰ and f_w^-) obtained through Density Functional Theory (DFT) calculations. Moreover, toxicity indexes of the oxidation products were obtained and compared to the parent SMX and MB using Toxicity Estimation Software Tool (TEST) software. Finally, the long-term operation performance of the Blue TiO₂/Ti membrane was evaluated.

Performance Optimization and Toxicity Effects of the Electrochemical Oxidation of Octogen

Octogen (HMX) is widely used as a high explosive and constituent in plastic explosives, nuclear devices, and rocket fuel. The direct discharge of wastewater generated during HMX production threatens the environment. In this study, we used the electrochemical oxidation (EO) method with a PbO2-based anode to treat HMX wastewater and investigated its degradation performance, mechanism, and toxicity evolution under different conditions. The results showed that HMX treated by EO could achieve a removal efficiency of 81.2% within 180 min at a current density of 70 mA/cm2, Na2SO4 concentration of 0.25 mol/L, interelectrode distance of 1.0 cm, and pH of 5.0. The degradation followed pseudo-first-order kinetics (R2 > 0.93). The degradation pathways of HMX in the EO system have been proposed, including cathode reduction and indirect oxidation by •OH radicals. The molecular toxicity level (expressed as the transcriptional effect level index) of HMX wastewater first increased to 1.81 and then decreased to a non-toxic level during the degradation process. Protein and oxidative stress were the dominant stress categories, possibly because of the intermediates that evolved during HMX degradation. This study provides new insights into the electrochemical degradation mechanisms and molecular-level toxicity evolution during HMX degradation. It also serves as initial evidence for the potential of the EO-enabled method as an alternative for explosive wastewater treatment with high removal performance, low cost, and low environmental impact.

Efficient eradication of antibiotic and dye by C-dots@zeolite nanocomposites: Performance evaluation, and degraded products analysis

Metronidazole (MET), a recalcitrant antibiotic from the nitro-imidazole family and commercially used Rhodamine B (RhB) dye, contributes a huge to water pollution, which needs to eliminate, preferably by photocatalytic degradation technique. The Cdots@zeolite (CDZ) nanocomposites with different weight ratios (1:1, 1:3, 1:5, 5:1, 1:7) were synthesized hydrothermally to degrade MET and RhB molecules. The CDZ composites were characterized by XRD, BET, EDS, and XPS technique which verifies the crystalline nature, incorporation of C-dots into zeolite frameworks with high surface area (∼187 m²/g). The morphology, d-spacing and lattice planes were analyzed by SEM images, HR-TEM and SAED analysis. The maximum degradation (∼79%) was achieved at an optimum catalyst dose of 0.2 g/L and pH 4 for MET and that of RhB was ∼90% at a catalyst dose of 0.4 g/L. The PZC (point of zero charge) value for CDZ composite was about pH 3.4, which justifies the maximum removal of MET at pH 4. The obtained rate constants 'k' were found to be 0.0081, 0.0041, and 0.0101 min^-1 in sun, UV, and visible light sources, respectively. The real industrial wastewater sample has been treated to give ∼68% of COD and ∼62% TOC removal. Moreover, the intermediates of plausible degradation pathways were identified by the m/z values obtained from GC-MS analysis.

Hydroxyl radicals in anodic oxidation systems: generation, identification and quantification

Anodic oxidation has emerged as a promising treatment technology for the removal of a broad range of organic pollutants from wastewaters. Hydroxyl radicals are the primary species generated in anodic oxidation systems to oxidize organics. In this review, the methods of identifying hydroxyl radicals and the existing debates and misunderstandings regarding the validity of experimental results are discussed. Consideration is given to the methods of quantification of hydroxyl radicals in anodic oxidation systems with particular attention to approaches used to compare the electrochemical performance of different anodes. In addition, we describe recent progress in understanding the mechanisms of hydroxyl radical generation at the surface of most commonly used anodes and the utilization of hydroxyl radical in typical electrochemical reactors. This review shows that the key challenges facing anodic oxidation technology are related to i) the elimination of mistakes in identifying hydroxyl radicals, ii) the establishment of an effective hydroxyl radical quantification method, iii) the development of cost effective anode materials with high corrosion resistance and high electrochemical activity and iv) the optimization of electrochemical reactor design to maximise the utilization efficiency of hydroxyl radicals.

Efficient electrochemical removal of 5-fluorouracil pharmaceutical from wastewater by mixed metal oxides via anodic oxidation process

Nowadays, the entry of organic compounds into water resources is one of the leading global concerns due to the lack of water resources and rapid population growth. In this research, anodic oxidation (AO) method was used to remove 5-fluorouracil (5-FU) from aqueous solutions via Ni/RuO₂ and Ti/IrO₂-TiO₂-RuO₂ electrodes as cathode and anode, respectively. For this purpose, the characterization analysis of the electrodes, including X-ray diffraction, scanning electron microscopy, energy dispersive X-ray, and atomic force microscopy were performed. The electrochemical performance of the anode was investigated via cyclic voltammetry analysis. Then, the effect of operational variables, including applied current (mA), initial pH of the solution, initial 5-FU concentration (mg/L), and process time (min) on the 5-FU removal efficiency under the AO process was evaluated via artificial neural network (ANN) modeling. The results revealed that the maximum 5-FU removal efficiency was 96.96%. The applied current intensity, pH, initial 5-FU concentration, and process time were 300 mA, 5, 20 mg/L, and 140 min, respectively. Moreover, the investigation of 5-FU removal by-products and mineralization efficiency of the AO process was carried out via gas chromatography-mass spectrometry and total organic carbon analysis, respectively. The total organic carbon mineralization efficiency was 84.80% after 6 h of reaction time. The reusability and stability of the Ti/IrO₂-TiO₂-RuO₂ anode on 5-FU removal efficiency were measured and showed an approximately 5% decay in 5-FU removal efficiency after eight consecutive runs. The overall results and analysis confirmed this method is capable of removing 5-FU through Ti/IrO₂-TiO₂-RuO₂ anode and Ni/RuO₂ cathode from aqueous medium.

Enhanced metronidazole removal by binary-species photoelectrogenic biofilm of microaglae and anoxygenic phototrophic bacteria

High efficient removal of antibiotics during nutriments recovery for biomass production poses a major technical challenge for photosynthetic microbial biofilm-based wastewater treatment since antibiotics are always co-exist with nutriments in wastewater and resist biodegradation due to their strong biotoxicity and recalcitrance. In this study, we make a first attempt to enhance metronidazole (MNZ) removal from wastewater using electrochemistry-activated binary-species photosynthetic biofilm of Rhodopseudomonas Palustris (R. Palustris) and Chlorella vulgaris (C. vulgaris) by cultivating them under different applied potentials. The results showed that application of external potentials of -0.3, 0 and 0.2 V led to 11, 33 and 26-fold acceleration in MNZ removal, respectively, as compared to that of potential free. The extent of enhancement in MNZ removal was positively correlated to the intensities of photosynthetic current produced under different externally applied potentials. The binary-species photoelectrogenic biofilm exhibited 18 and 6-fold higher MNZ removal rate than that of single-species of C. vulgaris and R. Palustris, respectively, due to the enhanced metabolic interaction between them. Application of an external potential of 0V significantly promoted the accumulation of tryptophan and tyrosine-like compounds as well as humic acid in extracellular polymeric substance, whose concentrations were 7.4, 7.1 and 2.0-fold higher than those produced at potential free, contributing to accelerated adsorption and reductive and photosensitive degradation of MNZ.

Application of lead oxide electrodes in wastewater treatment: A review

Electrochemical oxidation (EO) based on hydroxyl radicals (·OH) generated on lead dioxide has become a typical advanced oxidation process (AOP). Titanium-based lead dioxide electrodes (PbO₂/Ti) play an increasingly important role in EO. To further improve the efficiency, the structure and properties of the lead dioxide active surface layer can be modified by doping transition metals, rare earth metals, nonmetals, etc. Here, we compare the common preparation methods of lead dioxide. The EO performance of lead dioxide in wastewater containing dyes, pesticides, drugs, landfill leachate, coal, petrochemicals, etc., is discussed along with their suitable operating conditions. Finally, the factors influencing the contaminant removal kinetics on lead dioxide are systematically analysed.

Electrochemically reduced phytic acid-doped TiO2 nanotubes for the efficient electrochemical degradation of toxic pollutants

Element-doped TiO₂ nanotube arrays (TNAs) with optimized active sites provide an effective approach for significantly improving electrocatalytic performance. The challenges in such construction mainly include selection of green dopant and control of active sites. Herein, we present phytic acid as a phosphorus source for P-doped TNAs. An oxygen vacancy (Ov) and P co-doped TNAs (P-TiO_2-y) was prepared as an electrochemical oxidation anode. P-TiO_2-y exhibits excellent degradation activity due to the formation of Ti-O-P bonds and generation of Ov. P-doping was beneficial in improving the oxygen evolution potential of the electrode, which would be benefit for electrocatalytic degradation of pollutants. Using the P-TiO_2-y anode with a current density of 10 mA/cm² for tetracycline degradation, after a 3 h treatment, the removal rate, chemical oxygen demand and total organic carbon removal rates were 100%, 90.32% and 76.60%, respectively. The P-TiO_2-y also has excellent degradation performance for phenol, hydroquinone, p-nitrophenol and metronidazole.

New insights into the mechanisms of tartaric acid enhancing homogeneous and heterogeneous copper-catalyzed Fenton-like systems

The specific roles of tartaric acid (TA), as an eco-friendly ligand, in homogeneous and heterogeneous copper-catalyzed systems were systematically revealed and new mechanisms of TA enhancing the three Fenton-like processes were proposed to provide a theoretical significance in overcoming the deficiency of conventional Fenton processes. The results identified hydroxyl radical (•OH) as the main species responsible for the simultaneous decomposition of TA and metronidazole (MNZ) according to TOC removal. The ESR technique was used to detect superoxide radicals (•O₂^-), carbon-centered radical (•R) and hydrogen radical (•H) in the Cu²⁺/TA/H₂O₂ system, which contributed to the acceleration of the Cu²⁺/Cu⁺ redox cycle. The enhancing effect of TA on the homogeneous process was ascribed to the formation of a soluble complex with Cu²⁺, which favored the pH range extension, Cu⁺ oxidation, and radical generation. Moreover, the adsorption of TA on the catalysts surface promoted the consumption of H₂O₂, inducing •OH generation. The formed surface complex (≡Cu²⁺-TA) also accelerated the regeneration of ≡Cu⁺, which was confirmed by density functional theory (DFT) calculation and surface characterization analysis (SEM, XRD, and XPS). The possible degradation pathways of MNZ in TA-modified Fenton-like system were also clarified.

Moving-bed biofilm reactor combined with three-dimensional electrochemical pretreatment (MBBR-3DE) for 2,4-D herbicide treatment: application for real wastewater, improvement of biodegradability

2,4-Dichlorophenoxyacetic acid (2,4-D) is a herbicide that is considered as a carcinogenic and highly toxic contaminant, and due to its biological and chemical stability, its degradation is very difficult. Therefore, this study aimed to investigate a hybrid system's efficiency of three-dimensional electrochemical (3DE) process and a moving bed biofilm reactor (MBBR) in removing 2,4-D herbicides from aqueous solutions. In this experimental study, the electrochemical degradation of 2,4-D herbicide in a 3DE process with a G/β-PbO2 anode was first investigated as a pretreatment process. Then, in the post-treatment stage, MBBR with continuous flow was used. The amount of aeration in the MBBR reactor was 4 L min-1, and the amount of dissolved oxygen (DO) was in the range of 3-5 mg L-1. The effect of various parameters such as hydraulic retention time (HRT) and filling ratio were investigated. The amount of sewage injection was set between 0.001-0.004 L min-1. Routine microbiological biochemical tests were used to detect bacteria. BOD5/COD, COD/TOC, AOS, and COS ratio parameters were used to determine the biodegradability of 2.4-D due to the effluent of the 3DE process. The results showed that with increasing current density, decreasing pH, decreasing herbicide concentration and increasing electrolysis time, the herbicide degradation efficiency increased by 3DE pretreatment process. Based on the results of MBBR post-treatment process efficiency, with increasing HRT and filling ratio, the herbicide removal efficiency increased. According to the results, the highest removal efficiencies of 2,4-D and COD herbicides were obtained during HRT of 24 h, and the filling ratio of 70% were 97.33% and 88.95%, respectively. The consortium of 2,4-D degrading bacteria identified in this study included E. coli, Enterobacter spp., Bacillus spp., Alcaligenes spp., Proteus spp., Acinetobacter spp., Pseudomonas spp., Arthrobacter, and Brevundimonas vesicularis. In the MBBR biological process, the reaction kinetics followed the Grau second-order model (R 2 = 0.98). In general, the results showed that the combined process of 3DE with G/β-PbO2 anode and MBBR biological process has relatively high efficiency in 2,4-D herbicide degradation and can be used as a suitable complementary treatment method in wastewater containing non-degradable compounds such as phenoxy herbicides, e.g., 2,4-D should be used.

Fabrication of a multi-layer CNT-PbO2 anode for the degradation of isoniazid: Kinetics and mechanism

In this study, the CNTs were successfully compounded in PbO₂ electrode through composite electrodeposition technology to obtain multi-layer CNT-PbO₂ electrode. Scanning electron microscope, X-ray diffraction and X-ray Photoelectron Spectroscopy were comprehensively used to characterize the lead dioxide electrode and the electrochemical performance were also tested by cyclic voltammetry, and electrochemical impedance spectroscopy. Results showed that CNT-PbO₂ significantly improved the electrochemical performance, which was attributed to that the compound of CNTs in PbO₂ improved the active sites on the surface, with higher oxidation peaks, smaller particle size, larger specific surface area, and lower charge transfer resistance. In the degradation experiment, the chemical oxygen demand removal efficiency of isoniazid by CNT-PbO₂ electrode were 1.37 times of that by pure PbO₂ electrode. The main influence factors on the degradation of ISN, such as initial ISN concentration, Na₂SO₄ concentration, current density and initial pH value was analyzed in detail. Considered comprehensively the effects of ISN removal efficiency, COD and average current efficiency, the degradation of ISN and COD reached 99.4% and 86.8%, respectively, after the electrode was degraded by electrochemical oxidation for 120 min under the best conditions. In addition, the degradation mechanism of ISN in electrochemical oxidation was studied. According to the intermediate products detected by GC-MS, the possible degradation pathway of ISN in electrochemical oxidation system were proposed.

Catalytic potential of CuFe2O4/GO for activation of peroxymonosulfate in metronidazole degradation: study of mechanisms

Application of magnetite nanoparticles (CuFe2O4/GO) were anchored on graphene oxide (GO), as a Heterogeneous nanocomposite for activating of peroxymonosulfate (PMS) into Metronidazole (MNZ) destruction. The effect of solution pH, reaction time, effectiveness of water matrix components and trapping factors, different catalyst concentrations, PMS and contaminants were evaluated as operating factors on the efficiency of MNZ degradation. Also, mineralization, stability, reactivity and Recycling tests of the catalyst, and the degradation kinetics were performed. MNZ degradation and mineralization were obtained under optimal conditions (0.2 g/L catalyst, pH = 5, 30 mg/L MNZ and 2 mM PMS), 100% and 41.02%, respectively over 120 min. Leaching of Fe and Cu was found <0.2 mg/L for CuFe2O4/GO showed a high stability of catalyst, and a significant recyclability was achieved CuFe2O4/GO within 5 times consecutive use. MNZ degradation affected by anions was reduced as follows: HCO3 - > NO3 - > Cl- > SO4 2-. The experimental data were very good agreement with pseudo-first-order kinetic model, and during quenching tests SO4 •- radicals played a dominant role in the degradation process of MNZ. As a result, the CuFe2O4/GO/PMS system can be described as a promising activation of PMS in MNZ degradation, due to its high stability, reusability and good catalyst reactivity, and the production of reactive species simultaneously.

Electrochemical oxidation of ceftazidime with graphite/CNT-Ce/PbO2-Ce anode: Parameter optimization, toxicity analysis and degradation pathway

In this work, the electrochemical degradation of antibiotic ceftazidime has been studied using a novel rare earth metal Ce and carbon nanotubes codoped PbO₂ electrode. A competitively high oxygen evolution potential (2.4 V) and enhanced catalytic surface area were obtained, evidence by LSV and CV electrochemical characterization. The G/CNT-Ce/PbO₂-Ce electrode possessed a more compact structure and a smaller grain size than the other PbO₂ and Ce-PbO₂ electrodes, exhibiting a prolonged service lifetime, evidence by accelerated lifespan test and recycling degradation experiment. As electrolysis time reached 120 min, the removal efficiency of ceftazidime and TOC arrived at 100.0% and 54.2% respectively in 0.05 M Na₂SO₄ solution containing 50 mg⋅L^-1 ceftazidime. The effect of applied current density, pH value, initial ceftazidime concentration and chloride contents on the degradation performance were systematically evaluated. The results demonstrated that electrochemical oxidation of ceftazidime over the G/CNT-Ce/PbO₂-Ce electrode was highly effective, and the mineralization rate was greatly improved, compared with pristine PbO₂ electrode. Considering the toxicity was increased after 30 min electrolysis, the intermediates were quantitatively investigated through HPLC-MS, GC-MS and IC technology. According to the identified products, a reaction mechanism has been proposed and pyridine and aminothiazole were detected with concentration from approximately 1 to 3 mg⋅L^-1, which were regarded as toxic byproducts during electrooxidation. Further electrocatalyzing by ring cleavage reaction and complete mineralization to CO₂, NO₃^- and NH₄⁺ was proposed, which demonstrated the G/CNT-Ce/PbO₂-Ce electrode exhibited high efficiency for ceftazidime removal in mild conditions.