Highly efficient Fenton-like catalyst Fe-g-C3N4 porous nanosheets formation and catalytic mechanism

Singlet Oxygen Formation Mechanism for the H2O2-Based Fenton-like Reaction Catalyzed by the Carbon Nitride Homojunction

The singlet oxygen (1O2) oxidation process activated by metal-free catalysts has recently attracted considerable attention for organic pollutant degradation; however, the 1O2 formation remains controversial. Simultaneously, the catalytic activity of the metal-free catalyst limits the practical application. In this study, carbon nitride (HCCN) containing an intramolecular homojunction, a kind of metal-free catalyst, exhibits excellent activity compared to g-C3N4 (CN) and crystalline carbon nitride (HCN) for tetracycline hydrochloride degradation through the H2O2-based Fenton-like reaction. The rate constant for HCCN increased about 16.1 and 8.9 times than that of CN and HCN, respectively. The activity of HCCN was enhanced, and the dominant reactive oxygen species (ROS) changed from hydroxyl radicals (•OH) to 1O2 with an increase in pH from 4.5 to 11.5. A novel formation pathway of 1O2 was revealed. This result is different from the normal reference, in which •OH is always the primary ROS in the H2O2-based Fenton-like reaction. This study may provide a possible strategy for the investigation on the nonradical oxidation process in the Fenton-like reaction.

The powerful combination of 2D/2D Ni-MOF/carbon nitride for deep desulfurization of thiophene in fuel: Conversion route, DFT calculation, mechanism

2D/2D Ni-MOF/g-C3N4 nanocomposite was utilized for desulfurization. The multilayer pore structure and high specific surface area of Ni-MOF/g-C3N4 promote the adsorption and conversion of thiophene. In addition, the two-dimensional structure exposes more active centers and shortens photogenerated carrier migration to the material surface distance, it enhances photogenerated charge transfer. The Ni-MOF and g-C3N4 construct a Z-scheme heterojunction structure with tight contact, it effectively enhances the material's photocatalytic redox ability. In the light, the material generates more photocarriers for the production of free radicals including hydroxyl radicals, holes, and superoxide radicals. The higher carrier concentration of Ni-MOF/g-C3N4 promotes the activation and oxidation of thiophene, consequently enhancing the photocatalytic desulfurization capability. The results showed that the conversion of thiophene was 98.82 % in 3 h under visible light irradiation. Radical capture experiments and analysis using electron paramagnetic resonance spectroscopy demonstrated that superoxide radicals, holes, and hydroxyl radicals played crucial roles in PODS (photocatalytic oxidative desulfurization). In addition, DFT (density functional theory) calculations were conducted to determine the paths of electron migration and TH (thiophene) adsorption energy. Finally, a mechanism for photocatalytic desulfurization was proposed based on the comprehensive analysis of theoretical calculations and experimental studies.

Transition metals-doped g-C3N4 nanostructures as advanced photocatalysts for energy and environmental applications

Graphitic carbon nitride (g-C3N4)-based heterostructured photocatalysts have received significant attention for its potential applications in the treatment of wastewater and hydrogen evolution. The utilization of semiconductor materials in heterogeneous photocatalysis has recently received great attention due to their potential and eco-friendly properties. Doping with metal ions plays a crucial role in altering the photochemical characteristics of g-C3N4, effectively enhancing photoabsorption into the visible range and thus improving the photocatalytic performance of doped photocatalysts. As an emerging nanomaterial, nanostructured g-C3N4 represents a visible light-active semiconducting photocatalyst that has attracted significant interest in the photocatalysis field, particularly for its practical water treatment applications. To the best of our knowledge, investigations of functionalized photocatalytic (PC) materials on 3d transition metal-doped g-C3N4 remain unexplored in the existing literature. g-C3N4 based heterohybrid photocatalysts have demonstrated excellent reusability, making them highly promising for wastewater treatment applications. This paper describes the overview of numerous studies conducted on the heterostructured g-C3N4 photocatalysts with various 3d metals. Research studies have revealed that the introduction of element doping with various 3d transition metals (e.g., Ti, Mn, Fe, Co, Ni, Cu, Zn, etc.) into g-C3N4 is an efficient approach to enhance degradation efficacy and boost photocatalytic activity (PCA) of doped g-C3N4 catalysts. Moreover, the significance of g-C3N4 heterostructured nanohybrids is highlighted, particularly in the context of wastewater treatment applications. The study concludes by providing insights into future perspectives in this developing area of research, with a specific focus on the degradation of various organic contaminants.

Critical role of zero-valent iron in the efficient activation of H2O2 for 4-CP degradation by bimetallic peroxidase-like

Peroxidase-like based on double transition metals have higher catalytic activity and are considered to have great potential for application in the field of pollutant degradation. First, in this paper, a novel Fe0-doped three-dimensional porous Fe0@FeMn-NC-like peroxidase was synthesized by a simple one-step thermal reduction method. The doping of manganese was able to reduce part of the iron in Fe-Mn binary oxides to Fe0 at high temperatures. In addition, Fe0@FeMn-NC has excellent peroxidase-like mimetic activity, and thus, it was used for the rapid degradation of p-chlorophenol (4-CP). During the degradation process, Fe0 was able to rapidly replenish the constantly depleted Fe2+ in the reaction system and brought in a large number of additional electrons. The ineffective decomposition of H2O2 due to the use of H2O2 as an electron donor in the reduction reactions from Fe3+ to Fe2+ and from Mn3+ to Mn2+ was avoided. Finally, based on the experimental results of LC-MS and combined with theoretical calculations, the degradation process of 4-CP was rationally analyzed, in which the intermediates were mainly p-chloro-catechol, p-chloro resorcinol, and p-benzoquinone. Fe0@FeMn-NC nano-enzymes have excellent catalytic activity as well as structural stability and perform well in the treatment of simulated wastewater containing a variety of phenolic pollutants as well as real chemical wastewater. It provides some insights and methods for the application of peroxidase-like enzymes in the degradation of organic pollutants.

Graphitic carbon nitride membranes intercalated with nano-sized Fe-MOF for enhanced water purification via synergistic separation and Fenton-like processes

Versatile two-dimensional nanomaterials have offered a promising prospect to enhance the water purification efficiency and overcome the fouling obstacle in membrane technology. In this work, a graphitic carbon nitride (g-C3N4) nanosheet membrane intercalated with the nano-sized Fe-based metal-organic framework (MIL-100(Fe)) is developed for the enhanced removal of aqueous organic contaminants by synergically promoting separation and Fenton-like processes. The g-C3N4/MIL-100(Fe) membrane is constructed through a self-assembly route in which the nano-MIL-100(Fe) is anchored into g-C3N4 layers by the coordination bonds between Fe nodes and pyridinic N. The MIL-100(Fe) intercalation not only enlarges the interlayer spacing to raise the membrane permeability, but also expedites the electron transfer between Fe2+ and Fe3+ to improve the Fenton-like activity. With a stable water flux of 98.2 L m2·h-1·bar-1 under wide-range pH and pressures, the g-C3N4/MIL-100(Fe) membrane shows high dye removal efficiency (≥99%) and prominent self-cleaning ability. Mechanism insight proposes a combination of size exclusion, electrostatic interaction and steady radical generation. The intercalation of nano-MIL-100(Fe) into g-C3N4 membranes can realize the mutual promotion between separation and Fenton-like processes, the synergistic effect of which provides an effective and feasible strategy for aqueous pollution abatement.

Enhanced photocatalytic and antibacterial activities of novel Ag-HA bioceramic nanocatalyst for waste-water treatment

Hydroxyapatite (HA), the most common bioceramic material, offers attractive properties as a catalyst support. Highly crystalline mono-dispersed silver doped hydroxyapatite (Ag-HA) nanorods of 60 nm length was developed via hydrothermal processing. Silver dopant offered enhanced chemisorption for crystal violet (CV) contaminant. Silver was found to intensify negative charge on the catalyst surface; in this regard enhanced chemisorption of positively charged contaminants was accomplished. Silver dopant experienced decrease in the binding energy of valence electron for oxygen, calcium, and phosphorous using X-ray photoelectron spectroscopy XPS/ESCA; this finding could promote electron-hole generation and light absorption. Removal efficiency of Ag-HA nanocomposite for CV reached 88% after the synergistic effect with 1.0 mM H2O2; silver dopant could initiate H2O2 cleavage and intensify the release of active ȮH radicals. Whereas HA suffers from lack of microbial resistance; Ag-HA nanocomposite demonstrated high activity against Gram-positive (S. aureus) bacteria with zone of inhibition (ZOI) mm value of 18.0 mm, and high biofilm inhibition of 91.1%. Ag-HA nanocompsite experienced distinctive characerisitcs for utilization as green bioceramic photocatalyst for wastewater treatment.

Tuning Band Gap in Fe-Doped g-C3N4 by Zn for Enhanced Fenton-Like Catalytic Performance

Multiple oxidation states of first-row transition-metal cations were always doped in g-C₃N₄ to enhance the catalytic activity by the synergistic action between the cations in the Fenton-like reaction. It remains a challenge for the synergistic mechanism when the stable electronic centrifugation (3d¹⁰) of Zn²⁺ was used. In this work, Zn²⁺ was facilely introduced in Fe-doped g-C₃N₄ (named xFe/yZn-CN). Compared with Fe-CN, the rate constant of the tetracycline hydrochloride (TC) degradation increased from 0.0505 to 0.0662 min^-1 for 4Fe/1Zn-CN. The catalytic performance was more outstanding than those of similar catalysts reported. The catalytic mechanism was proposed. With the introduction of Zn²⁺ in 4Fe/1Zn-CN, the atomic percent of Fe (Fe²⁺ and Fe³⁺) and the molar ratio of Fe²⁺ to Fe³⁺ at the catalyst's surface increased, where Fe²⁺ and Fe³⁺ were the active sites for adsorption and degradation. In addition, the band gap of 4Fe/1Zn-CN decreased, leading to enhanced electron transfer and conversion from Fe³⁺ to Fe²⁺. These changes resulted in the excellent catalytic performance of 4Fe/1Zn-CN. Radicals •OH, •O₂^-, and ¹O₂ formed in the reaction and took different actions under various pH values. 4Fe/1Zn-CN exhibited excellent stability after five cycles under the same conditions. These results may give a strategy for synthesizing Fenton-like catalysts.

Ultrafine ZnCo2O4 QD-incorporated carbon nitride mediated peroxymonosulfate activation for norfloxacin oxidation: performance, mechanisms and pathways

Recently, peroxymonosulfate (PMS)-based advanced oxidation processes (AOPs) are being actively investigated as a potential technology for water decontamination and many efforts have been made to improve the activation efficiency of PMS. Herein, a 0D metal oxide quantum dot (QD)-2D ultrathin g-C3N4 nanosheet (ZnCo2O4/g-C3N4) hybrid was facilely fabricated through a one-pot hydrothermal process and used as an efficient PMS activator. Benefiting from the restricted growth effect of the g-C3N4 support, ultrafine ZnCo2O4 QDs (∼3-5 nm) are uniformly and stably anchored onto the surface. The ultrafine ZnCo2O4 possesses high specific surface areas and shortened mass/electron transport route so that the internal static electric field (Einternal) formed in the interface between p-type ZnCo2O4 and the n-type g-C3N4 semiconductor could speed up the electron transfer during the catalytic reaction. This thereby induces the high-efficiency PMS activation for rapid organic pollutant removal. As expected, the ZnCo2O4/g-C3N4 hybrid catalysts significantly outperformed individual ZnCo2O4 and g-C3N4 in catalytic oxidative degradation of norfloxacin (NOR) in the presence of PMS (95.3% removal of 20 mg L-1 of NOR in 120 min). Furthermore, the ZnCo2O4/g-C3N4-mediated PMS activation system was systematically studied in terms of the identification of reactive radicals, the impact of control factors, and the recyclability of the catalyst. The results of this study demonstrated the great potential of a built-in electric field-driven catalyst as a novel PMS activator for the remediation of contaminated water.

Preparation and Characterization of a Coordination Polymer Based on Iron (III)-Cyamelurate as a Superior Catalyst for Heterogeneous Fenton-Like Processes

We report on a new iron (iii)-cyamelurate-based coordination polymer. The new material based on a heptazine derivative was prepared in aqueous medium and characterized by a variety of techniques including TGA, FTIR, XRD, HRTEM, and STEM. Due to the high structural stability of the complex in aqueous media, its heterogeneous Fenton-like catalytic activity was evaluated using a model molecule. The results obtained showed a high catalytic activity in both in basic and acid media. The pseudo-first-order rate constants normalized by iron(III) concentrations was approximately 1000 times higher than the result obtained for traditional heterogeneous catalysts based on iron(III) oxyhydroxides. The best observed catalytic activities were attributed to the increase in the binding sites of Fe³⁺ ions, in parallel with the increased exposure of the catalytic sites, leading to a higher atomic efficiency of the reaction.

Peroxidase-like activity of hollow sphere-like FeS2/SC boosted by synergistic action of defects and S-C bonding

Pyrite FeS₂ has been applied as a peroxidase due to its easy preparation and low cost. However, the low peroxidase-like (POD) activity limited its wide application. A hollow sphere-like composite (FeS₂/SC-5.3%) composed of pyrite FeS₂ and sulfur-doped hollow sphere-shaped carbon was synthesized by a facile solvothermal method, where the S-doped carbon was in situ formed during FeS₂ formation. The synergistic action such as the defects at the carbon surface and the formation of S-C bonding improved the nanozyme activity. The S-C bonding was a bridge between the carbon and the Fe atom in FeS₂, which enhanced the electron transfer between the Fe atom and the carbon and accelerated the conversion from Fe³⁺ to Fe²⁺. The optimum experimental conditions were obtained by the response surface methodology (RSM). The POD-like activity of FeS₂/SC-5.3% was significantly improved compared to that of FeS₂. The Michaelis-Menten constant (K_m) of FeS₂/SC-5.3% is 80 times lower than that of horseradish peroxidase (HRP, natural enzyme). FeS₂/SC-5.3% can be used to detect cysteine (Cys) with a limit of detection (LOD) as small as 0.061 μM at room temperature in only 1 min.

Constructing a 3D interconnected "trap-zap" β-CDPs/Fe-g-C3N4 catalyst for efficient sulfamethoxazole degradation via peroxymonosulfate activation: Performance, mechanism, intermediates and toxicity

A novel and high-efficiency catalyst Fe doped g-C₃N₄ (Fe-g-C₃N₄) composited with β-cyclodextrin polymers (β-CDPs) was synthesized for activating peroxymonosulfate (PMS). The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results showed that the catalyst was 3D interconnected porous structure. The degradation rate constant of sulfamethoxazole (SMX) in β-CDPs/Fe-g-C₃N₄+PMS system was estimated to be 0.132 min^-1, which was 14.7 times and 2.2 times that of g-C₃N₄+PMS and Fe-g-C₃N₄+PMS system, respectively. In addition, the β-CDPs/Fe-g-C₃N₄ exhibited superior degradation performance in a wide pH range (3.0-9.0) and good selectivity in the presence of other inorganic anions and natural organics. Radical scavenging, electron paramagnetic resonance (EPR) and electrochemical measurements indicated that ¹O₂ and Fe(V)O were the main active species for SMX degradation in β-CDPs/Fe-g-C₃N₄+PMS system. Moreover, β-CDPs accelerated electron transfer between catalyst and PMS and promoted the generation of reactive oxygen species (ROS) during PMS activation. The loading of β-CDPs increased the yields of Fe(V)O and ¹O₂ in the system and limited the leaching of Fe³⁺. In addition, the possible degradation pathways of SMX were described based on the intermediates detected by liquid chromatography-mass spectrometry (LC-MS), and the toxicity of the intermediates was also evaluated. This work investigate the role of β-CDPs in PMS activation for the first time and develop a promising material with potential for water treatment.

Construction of 2D layered phosphorus-doped graphitic carbon nitride/BiOBr heterojunction for highly efficient photocatalytic disinfection

Infectious diseases caused by bacteria intimidate the health of human beings all over the world. Although many avenues have been tried, various operating conditions limit their actual applications. Photocatalytic nanomaterials are becoming candidates to be competent for water purification. Here, a novel and more efficient S-scheme has been engineered between two dimensional (2D) layered phosphorus-doped graphitic carbon nitride (P-g-C 3 N 4 ) and BiOBr via hydrothermal polymerization to inhibit the recombination of charge and broaden light absorption. The as-prepared P-g-C 3 N 4 /BiOBr hybrids exhibits significantly improved photocatalytic disinfection contrast to g-C 3 N 4 /BiOBr in visible wavelengths, suggesting phosphorus doping which adjusts the band structure plays a significant role in the S-scheme system. And the sterilization rate of multidrug-resistant Acinetobacter baumannii 28 ( AB 28 ) was 99.9999% within 80 min and Staphylococcus aureus ( S. aureus ) was 99.9%.

Porous P, Fe-doped g-C3N4 nanostructure with enhanced photo-Fenton activity for removal of tetracycline hydrochloride: Mechanism insight, DFT calculation and degradation pathways

This study fabricated an efficient P and Fe co-doping graphitic carbon nitride catalyst (Fe- CN/P) by thermal polymerization of melamine, FeCl₃, and 2-hydroxyphosphonoacetic acid (HPAA) mixture. The Fe-CN/P catalyst exhibited much better tetracycline hydrochloride (TCH) degradation performance than that of single doping and neat CN. Various characterizations indicated that the introduction of HPAA significantly increased the specific surface area of CN and improved charge separation as well as transfer efficiency. Based on Fe 2p XPS analysis and indirect determination of hydroxyl radical (·OH) content, the separated photogenerated electrons accelerated the reduction of Fe(III) and activated photo-Fenton reaction, resulting in more ·OH species generation. The effect of pH value, catalyst dosages, H₂O₂ concentration, the type of cations and anions as well as water matrices on the degradation of TCH by Fe-CN/P was systematically investigated. The main degradation pathways of TCH were proposed according to the LC-MS intermediates detection and DFT calculation. The results indicated that reactive oxide species (ROS) were more likely to attack the atoms with high Fukui index (f⁰). This work provides new ideas for adjusting the morphology and electronic structure of CN to enhance its photo-Fenton catalytic activity.

High-density dispersion of CuNx sites for H2O2 activation toward enhanced Photo-Fenton performance in antibiotic contaminant degradation

In this study, a copper-based catalyst (CuCN) with CuN_x active sites highly dispersed in a porous carbon nitride matrix was synthesized and applied to a heterogeneous photo-assisted Photo-Fenton (PF) system to degrade tetracycline (TET). The results showed that the CuCN/PF system degraded up to 93.6% of TET within 60 min for ultrapure water matrix under the best experimental conditions, and more than 70% of TET for both river and lake water matrix. Toxicological tests suggested that the environmental risk caused by TET can be effectively inhibited by the CuCN/PF system. The good visible-light response and charge transport abilities of CuCN catalyst were identified in photoelectrochemical experiments. Free radical scavenging experiments and electron paramagnetic resonance (EPR) spectroscopy indicated that the active species in the degradation process were·OH, h⁺,·O₂^- and ¹O₂. Density functional theory (DFT) calculations revealed the positive effect of CuN_x sites in CuCN on the formation of hydroxyl radicals by activating H₂O₂. This work will provide a new insight for the development of high-efficiency heterogeneous catalysts in wastewater environmental remediation.

Recent advances in graphitic carbon nitride as a catalyst for heterogeneous Fenton-like reactions

Graphitic carbon nitride (g-C₃N₄), an appealing metal-free polymer, has featured in extensive research in heterogeneous Fenton-like reactions owing to its advantages of stable chemical and thermal properties, ease of structural regulation and unique redox ability. However, there are still some gaps in the understanding of the mechanism and fate of g-C₃N₄ and its derivatives in heterogeneous Fenton reaction degradation of contaminants. This paper gives systematic emphasis to the development and progress of g-C₃N₄ and its composites as catalysts in heterogeneous Fenton-like reactions. The main synthesis strategies of g-C₃N₄ composites are discussed, including calcination, hydrothermal method and self-assembly method. Then, the key catalytic properties of g-C₃N₄ in Fenton-like applications, including anchoring nanoparticles, increasing specific surface area and exposed active surface sites, as well as regulating charge transfer reactions, are highlighted. Special emphasis is placed on its multifunctional role in heterogeneous Fenton-like reactions and the mechanisms involved in the activation of hydrogen peroxide, persulfates, and photocatalytic activation of persulfate. Lastly, the existing challenges and possible development direction of g-C₃N₄-coupling Fenton reactions are proposed. It is believed that this paper will bring useful information for the development of graphitic carbon nitride in both laboratory studies and practical applications.

Mesoporous structure and amorphous Fe-N sites regulation in Fe-g-C3N4 for boosted visible-light-driven photo-Fenton reaction

Heterogeneous photo-Fenton catalysts prepared by doping metal ions in g-C₃N₄ are promising alternatives to traditional homogeneous Fenton catalysts, but are restricted by poor mesoporous structure and agglomerate of metal species. Recently, the highly uniformly dispersed metal-N active sites in various photocatalysts have been proved to be the critical reason for their enhanced catalytic activity. In this study based on reasonable control of mesoporous structure and metal-N active sites, mesoporous Fe-g-C₃N₄ was synthesized using a simple one-step thermal shrinkage polymerization method using ferrous oxalate as iron source and pore-forming agent. The Fe and N elements in the triazine ring skeleton of Fe-g-C₃N₄ form a σ-π bond, thus the photogenerated electrons can be quickly transferred to Fe³⁺ to form Fe²⁺ under the interaction of chemical bonds, accelerating the Fenton reaction rate. Density functional theory calculations results demonstrate that the energy band structure and electron cloud density distribution of Fe-Nx active structure are better than that of routine FeOx crystal structure with metal species agglomeration. In addition, the excellent mesoporous structure of Fe-g-C₃N₄ creates conditions for the high exposure of Fe-Nx active sites in the photo-Fenton reaction under visible light. The as-developed Fe-g-C₃N₄ system shows high recyclability and excellent photo-Fenton performance for removal of typical intractable pollutants (The degradation rate of dye and tetracycline reaches 98.2% and 98.7% at 60 and 120 min, respectively). This work provides a facile and sustainable route to develop mesoporous highly-active heterogeneous Fenton-like catalysts and even further general the design of general catalyst with ideal metal-N active sites, thereby promoting a feasible and efficient wastewater remediation solution.

Removal of organic compounds by nanoscale zero-valent iron and its composites

During the latest several decades, the continuous development of the economy and industry has brought more and more serious organic pollutants to the natural environment, which have inevitably aroused severe menace to human health and the environmental system. The nano zero-valent iron (NZVI) particles and NZVI-based materials have widely applied to remove organic pollutants. This article reviews the key advancements of different methods for the synthesis of NZVI and NZVI-based materials. Different modification methods (e.g., doped NZVI, encapsulated NZVI and supported NZVI) are also introduced detailedly for overcoming the defects of NZVI such as aggregation and easy oxidation. The removal of different organic pollutants including dyes, halogenated organic compounds, nitro-organic compounds, phenolic compounds, pesticides, and antibiotics are summarized. The interaction mechanisms, including adsorption, reduction, and active oxidation of organic pollutants by NZVI/NZVI-based composites, are discussed. The dyes are mainly removed by destroying their chromogenic group according to the reduction or the Fenton-like reaction with NZVI. The removal of halogenated organic compounds (HOCs) is realized by the dehalogenation process, including reductive elimination, hydrogenolysis, and hydrogenation. As for the nitro-organic compounds, three different reduction pathways as nitro-reduction (into amino), cleavage at the carbon‑nitrogen bond or denitration of the NO₂ group may take effect. The phenolic compounds can be mineralized into inorganic molecules, including CO₂ and H₂O, by Fenton oxidation. This review might provide the basis for future studies on developing more effective NZVI-based materials for the treatment of wastewaters contaminated by organic pollutants.

Insight into the synergetic effect of photocatalysis and transition metal on sulfite activation: Different mechanisms for carbamazepine and diclofenac degradation

Sulfite [S(IV)] is a promising alternative for sulfate radical-based advanced oxidation processes (SR-AOPs). Transition metal and photocatalysis are generally considered to have a synergetic effect for S(IV) activation. However, the study shows that the synergetic effect is target specific. Herein, an ultra-small Fe₂O₃ clusters deposited graphitic carbon nitride is synthesized and used for S(IV) activation. For carbamazepine (CBZ) degradation, photogenerated holes can transform S(IV) into sulfate radical and photogenerated electrons can accelerate Fe(II)/Fe(III) cycle, which account for the synergetic effect. In contrast, the degradation of diclofenac (DCF) depends on the excitation of DCF rather than photocatalyst. Instead of radical precursor, S(IV) acts as the electron transfer bridge between excited DCF and photocatalyst. Thus, the deposition of Fe₂O₃ negatively affects DCF degradation. Density Functional Theory calculation shows that the first excited state rather than the ground state of diclofenac is more suitable for reactive site prediction, which confirms the photosensitization-like degradation mechanism. Moreover, the effects of pH and coexisted anions varies for CBZ and DCF. The study shed light on the synergetic effect of transition metal and photocatalysis for S(IV) activation, and also open an avenue for the study of target specific mechanisms for AOPs.

Synergistically homogeneous-heterogeneous Fenton catalysis of trace copper ion and g-C3N4 for degradation of organic pollutants

Using the bulk g-C₃N₄ as a precursor, four g-C₃N₄ nanosheets were further prepared by ultrasonic, thermal, acid, and alkali exfoliation. The structures of these materials were characterized by various techniques such as X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. The synergistical Fenton catalysis of these materials with Cu²⁺ was evaluated by using rhodamine B as a simulated organic pollutant. The results showed that there existed a significant synergistical Fenton catalysis between Cu²⁺ and g-C₃N₄. This synergistic effect can be observed even when the concentration of Cu²⁺ was as low as 0.064 mg L^-1. The properties of g-C₃N₄ strongly influenced the catalytic activity of the Cu²⁺/g-C₃N₄ system. The coexistent of Cu²⁺ and the alkali exfoliated g-C₃N₄ showed the best catalytic activity. Hydroxyl radicals as oxidizing species were confirmed in the Cu²⁺/g-C₃N₄ system by electron paramagnetic resonance spectra. The synergistic catalysis may be attributed to the easier reduction of Cu²⁺ adsorbed on the g-C₃N₄. This study provided an excellent Fenton catalytic system, and partly solved the rapid deactivation of heterogeneous Fenton catalysts caused by the leaching of metal ions.

Enhanced Fenton-like catalytic activity and stability of g-C3N4 nanosheet-wrapped copper phosphide with strong anti-interference ability: Kinetics and mechanistic study

Metal-based Fenton-like catalysts usually activate H₂O₂ to produce free radicals (^•OH and O₂^•-) for the degradation of organic pollutants. However, a catalytic reaction dominated by free radicals is easily interfered with by various inorganic anions and water matrices. Herein, g-C₃N₄-wrapped copper phosphide (Cu_xP), as a highly efficient Fenton-like catalyst, was successfully synthesized by a simple low-temperature phosphidation method. The Cu_xP/g-C₃N₄ catalyst exhibited excellent catalytic ability for the removal of various organic contaminants over a wide pH range of 3-11. In addition, the catalyst exhibited strong anti-interference ability toward various inorganic anions (Cl^-, SO₄^2-, NO₃^-, F^-, H₂PO₄^-, HCO₃^- and CO₃^2-) and water matrices (lake water, river water, tap water and simulated water matrix). The reasons for this performance were analyzed by verifying the mechanism of the catalytic reaction. Compared to the pure Cu_xP catalyst, the Cu_xP/g-C₃N₄ composite possessed good catalytic stability. The enhanced and deactivated mechanisms of the Cu_xP/g-C₃N₄ catalyst were systematically analyzed by a series of characterization techniques. A possible reaction mechanism was also proposed based on the experimental results. This work provides new insights into designing highly efficient metal-based Fenton-like catalysts with strong anti-interference ability to practically treat wastewater.

Iron nanoparticles encapsulated within nitrogen and sulfur co-doped magnetic porous carbon as an efficient peroxymonosulfate activator to degrade 1-naphthol

A novel iron nanoparticles encapsulated within nitrogen and sulfur co-doped magnetic porous carbon (Fe-N-S-MPC) was proposed by one-pot pyrolysis strategy to activate peroxymonosulfate (PMS) to degrade 1-naphthol using low-cost lignin as precursors. The Fe-N-S-MPC was characterized for structure and properties by different characterizations. The obtained materials had the morphology of iron nanoparticles encapsulated within nitrogen and sulfur co-doped magnetic porous carbon with rich functional groups and large specific surface area, which made the materials have a good catalytic property. It was proved that the doping of nitrogen and sulfur is pivotal for improving the catalytic performance. The radical quenching experiment confirmed that sulfate radical (SO₄^-) and hydroxyl radical (OH) are two major reactive oxygen groups. The reaction had phenomenon of the free radicals upsurge in the early stage and the shortage in the later stage. Therefore, a mathematical model was put forward to represent the two-stage reaction kinetics. By adding oxidants in batches, the degradation effect could reach nearly 100% within 30 min. The Fe-N-S-MPC were applied to the degradation of 1-naphthol in soil and showed high degradation performance. This work provided a new type of catalytic material by the high-value utilization of waste for the degradation of organic pollutants.

Recent advances in application of graphitic carbon nitride-based catalysts for degrading organic contaminants in water through advanced oxidation processes beyond photocatalysis: A critical review

Advanced oxidation processes (AOPs) have attracted much interest in the field of water treatment owing to their high removal efficiency for refractory organic contaminants. Graphitic carbon nitride (g-C₃N₄)-based catalysts with high performance and cost effectiveness are promising heterogeneous catalysts for AOPs. Most research on g-C₃N₄-based catalysts focuses on photocatalytic oxidation, but increasingly researchers are paying attention to the application of g-C₃N₄-based catalysts in other AOPs beyond photocatalysis. This review aims to concisely highlight recent state-of-the-art progress of g-C₃N₄-based catalysts in AOPs beyond photocatalysis. Emphasis is made on the application of g-C₃N₄-based catalysts in three classical AOPs including Fenton-based processes, catalytic ozonation and persulfates activation. The catalytic performance and involved mechanism of g-C₃N₄-based catalysts in these AOPs are discussed in detail. Meanwhile, the effect of water chemistry including pH, water temperature, natural organic matter, inorganic anions and dissolved oxygen on the catalytic performance of g-C₃N₄-based catalysts are summarized. Moreover, the reusability, stability and toxicity of g-C₃N₄-based catalysts in water treatment are also mentioned. Lastly, perspectives on the major challenges and opportunities of g-C₃N₄-based catalysts in these AOPs are proposed for better developments in the future research.

Facile synthesis of Cu-CuFe2O4 nanozymes for sensitive assay of H2O2 and GSH

Artificial enzymes have drawn substantial research interest from the scientific community due to their advantages over natural enzymes. However, majority of artificial enzymes exhibit low affinity towards H2O2, which means that a high H2O2 concentration is needed for the oxidation of a substrate such as 3,3',5,5'-tetramethylbenzidine (TMB) to blue-colored oxTMB. With this concern, Cu-CuFe2O4 was facilely synthesized, wherein, Cu0 accelerates the redox capacity of Cu-CuFe2O4 as well as the electron transfer between CuFe2O4 and H2O2. These materials induce excellent activity as a peroxidase. Cu-CuFe2O4 shows high affinity towards H2O2 with lower Michaelis-Menten constant (Km) than the reported values for ferrites and Horseradish enzyme (HRP). Moreover, it took only 5 min to detect hydrogen peroxide (H2O2) and glutathione (GSH) through a colorimetric assay using Cu-CuFe2O4. Compared with CuFe2O4, the limit of detection (LOD) is about 90-fold lower for H2O2 using Cu-CuFe2O4. In addition, Cu-CuFe2O4 shows high stability as a nanozyme. Thus, the mechanism of the peroxidase-like nanozyme Cu-CuFe2O4 is proposed.

Ru/g-C3N4 as an efficient catalyst for selective hydrogenation of aromatic diamines to alicyclic diamines

A series of Ru/g-C3N4 materials with highly dispersed Ru were firstly prepared by an ultrasonic impregnation method using carbon nitride as a support. The catalysts were characterized by various techniques including BET and elemental analysis, ICP-AES, XPS, XRD, CO2-TPD and TEM. The results demonstrated that Ru/g-C3N4 materials with a mesoporous structure and highly dispersed Ru were successfully prepared. The chemo-selective hydrogenation of p-phenylenediamine (PPDA) to 1,4-cyclohexanediamine (CHDA) over Ru/g-C3N4 as a model reaction was investigated in detail. PPDA conversion of 100% with a CHDA selectivity of more than 86% could be achieved under mild conditions. It can be inferred that the carbon nitride support possessed abundant basic sites and the Ru/g-C3N4-T catalysts provided suitable basicity for the aromatic ring hydrogenation. Compared to the N-free Ru/C catalyst, the involvement of nitrogen species in Ru/g-C3N4 remarkably improved the catalytic performance. In addition, the recyclability of the catalyst demonstrated that the aggregation of Ru nanoparticles was responsible for the decrease of the catalytic activity. Furthermore, this strategy also could be expanded to the selective hydrogenation of other aromatic diamines to alicyclic diamines.