Z-scheme MoO3 anchored-hexagonal rod like ZnO/Zn photoanode for effective wastewater treatment, copper reduction accompanied with electricity production in sunlight-powered photocatalytic fuel cell

Eminent destruction of organics and pathogens concomitant with power generation in a visible light-responsive photocatalytic fuel cell with NiFe2O4/ZnO pine tree-like photoanode and CuO/Cu2O nanorod cathode

Environmental conservation and energy scarcity have become two core challenges with the ever-increasing advancement of industry, particularly chemical energy rich wastewater comprising refractory organics and pathogenic microbes. Here, a multifunctional photocatalytic fuel cell (PFC) was devised using NiFe2O4 nanoparticle-loaded on pine tree-like ZnO/Zn (NiFe2O4/ZnO/Zn) photoanode and CuO/Cu2O nanorods-loaded on Cu (CuO/Cu2O/Cu) cathode for extracting electricity upon wastewater treatment. When fed with Rhodamine B (RhB) dyestuff, the NiFe2O4/ZnO/Zn-PFC provided the maximum power density (Pmax) of 0.539 mW cm-2 upon visible light irradiation with an average RhB degradation of 85.2%, which were 2.8 and 2.7 times higher than ZnO/Zn, respectively. The remarkable enhanced NiFe2O4/ZnO/Zn-PFC performance was owing to the synergistic effect of pine tree-like structure and Z-scheme heterostructure. The pine tree-like with high surface area was not only for effective harnessing photon energies but also provided more directional routes for rapid segregation and transport of carriers and higher interface contacting areas with electrolyte. Through a series of systematic characterizations, the Z-scheme heterostructure mechanism of the system and organics degradation pathway were also speculated. Additionally, the performance of the NiFe2O4/ZnO/Zn-PFC in industry printing wastewater showed Pmax of 0.600 mW cm-2, which was considerably impressive as real wastewater was challenging to accomplish. The phytotoxicity outcome also manifested that the comprehensive toxicity of RhB was eradicated after PFC treatment. Lastly, the excellent recyclability and the pronounced bactericidal effect towards Escherichia coli and Staphylococcus aureus were other attributions which enabled the NiFe2O4/ZnO/Zn-PFC for possible practical application.

Sustainable degradation of pollutants, generation of electricity and hydrogen evolution via photocatalytic fuel cells: An Inclusive Review

Environmental pollution and energy crisis have recently become one of the major global concerns. Insincere discharge of massive amount of organic and inorganic wastes into the aqueous bodies causes serious impact on our environment. However, these organic substances are significant sources of carbon and energy that could be sustainably utilized rather than being discarded. Photocatalytic fuel cell (PFC) is a smart and novel energy conversion device that has the ability to achieve dual benefits: degrading the organic contaminants and simultaneously generating electricity, thereby helping in environmental remediation. This article presents a detailed study of the recent advancements in the development of PFC systems and focuses on the fundamental working principles of PFCs. The degradation of various common organic and inorganic contaminants including dyes and antibiotics with simultaneous power generation and hydrogen evolution has been outlined. The impact of various operational factors on the PFC activity has also been briefly discussed. Moreover, it provides an overview of the design guidelines of the different PFC systems that has been developed recently. It also includes a mention of the materials employed for the construction of the photo electrodes and highlights the major limitations and relevant research scopes that are anticipated to be of interest in the days to come. The review is intended to serve as a handy resource for researchers and budding scientists opting to work in this area of PFC devices.

Polyaniline/g-C3N4/Bi2O3/Ti photoanode for visible light responsive photocatalytic fuel cell degradation of rhodamine B and electricity generation

In order to develop efficient photoanode to improve the performance of visible light responsive photocatalytic fuel cell (PFC), in this work, polyaniline/g-C₃N₄/Bi₂O₃/Ti photoanode was successfully prepared using silica-sol drop coating method, and assembled with Cu cathode to construct PFC to decompose rhodamine B and generate electricity simultaneously. The degradation rate, maximum photocurrent density and maximum power density of this PFC were 91.23%, 0.086 mA cm^-2 and 4.78 μW cm^-2, respectively, which were 1.4 and 1.8 times, 2.4 and 4.5 times, and 1.9 and 7.3 times those of the corresponding values of the PFCs with g-C₃N₄/Bi₂O₃/Ti and Bi₂O₃/Ti photoanodes, respectively. This is attributed to the type II heterojunction structure formed among polyaniline, g-C₃N₄ and Bi₂O₃ in the polyaniline/g-C₃N₄/Bi₂O₃/Ti photoanode. Among them, polyaniline has π-π conjugated structure, which can rapidly transfer the electronic charge between g-C₃N₄ and Bi₂O₃, thus enhancing the separation efficiency of photo-generated e^--h⁺ pairs spatially and reducing their recombination, extending the visible light response wavelength of the photocatalyst, and finally improving its photocatalytic properties. This study can provide significant reference for the research of Bi₂O₃-based visible light responsive PFC.

Flower ball cathode assembled from Cu doped Co3S4/Ni3S2 ultrathin nanosheets in a photocatalytic fuel cell for efficient photoelectrochemical rifampicin purification and simultaneous electricity generation based on a CuO QDs/TiO2/WO3 photoanode

Herein, an efficient CuO QDs/TiO₂/WO₃ photoanode and a Cu doped Co₃S₄/Ni₃S₂ cathode were successfully synthesized. The optimized CuO QDs/TiO₂/WO₃ photoanode achieved a photocurrent density of 1.93 mA cm^-2 at 1.23 vs. RHE, which was 2.27 times that of a WO₃ photoanode. The CuO QDs/TiO₂/WO₃-buried junction silicon (BJS) photoanode was coupled with the Cu doped Co₃S₄/Ni₃S₂ cathode to construct a novel photocatalytic fuel cell (PFC) system. The as-established PFC system showed a high rifampicin (RFP) removal ratio of 93.4% after 90 min and maximum power output of 0.50 mW cm^-2. Quenching tests and EPR spectra demonstrated that ˙OH, ˙O₂^- and ¹O₂ were the main reactive oxygen species in the system. This work provides a possibility to construct a more efficient PFC system for environmental protection and energy recovery in the future.

Sharp-edged pencil type ZnO flowers and BiOI flakes combined with carbon nanofibers as heterostructured hybrid photocatalysts for the removal of hazardous pollutants from contaminated water

The growth of advanced micro-and nanostructures with metal oxides has consistently generated extraordinary interest in energy and environmental applications. Cutting-edge nanostructures exhibit superior reactive sites and surface areas, thus improving the performance in crucial domains. In this study, sharp-edged pencil-type ZnO flowers and BiOI flakes as pristine materials, and their composition with carbon nanofibers (CNFs) (ZnO-BiOI@CNFs) as a hetero hybrid catalyst as well as binary compositions such as ZnO-BiOI, ZnO@CNFs, and BiOI@CNFs catalysts were fabricated using a simple and convenient hydrothermal synthesis process. The composition of newly produced innovative nanostructures was examined for azo dye degradation under solar simulator exposure. Dye degradation of ∼95% was achieved by the hybrid catalyst (ZnO-BiOI@CNFs) during 120 min of irradiation, which was ∼1.8 and 2.1-times higher than pristine ZnO and BiOI nanostructures, respectively. The improved hybrid catalysts were able to degrade methyl orange (MO) and rhodamine B (RhB) dyes. Importantly, mixed dyes RhB, MO, and azo dye demonstrated 47% dye degradation using a hybrid catalyst. These mixed dye-scalable hybrid catalyst performances offer additional insights into commercialization/industrialization. The outstanding performance of the hybrid catalyst is attributed to the unidirectional electron flow with pencil-like ZnO, a catalyst with a larger absorption zone, high surface area, and reactive sites, particularly ZnO and BiOI nanostructures, and decreased recombination rate with a heterojunction interface. In addition, CNFs can operate as electron traps and sinks, providing very quick redox reactions. To produce the sophisticated nanostructures with homogeneous morphologies, this work presents new insights into energy and environmental applications.

Photocatalysis of carbamazepine via activating bisulfite by ultraviolet: Performance, transformation mechanism, and residual toxicity assessment of intermediates products

Carbamazepine (CBZ) as an extensively distributed emerging pollutant has menaced ecological security. The degradation performance of CBZ by UV driven bisulfite process was investigated in this work. The kinetics results indicated that CBZ was high-efficiently degraded by UV/bisulfite following a pseudo first-order kinetic model (K_obs = 0.0925 min^-1). SO₄^•- and •OH were verified as the reactive oxidants by EPR test and the radicals scavenging experiment using MeOH and TBA. SO₄^•- played a dominant role for CBZ degradation. The Density functional theory (DFT) and LC-qTOF-MS/MS clarified that hydroxylation, ketonation, ring opening reaction, and ring contraction were main transformation patterns of CBZ. As to influence factors, CBZ degradation was significantly hindered in presence of CO₃^2-, HPO₄^2- and NOM. Toxicological analysis derived from metabonomics suggested that the remarkable alteration of metabolic profile was triggered by exposure to intermediates mixture. CBZ intermediates interfered in several key metabolic pathways, including pentose phosphate, amino acids, lysine degradation, glycerophospholipid, glutathione, nucleotides and carbohydrate, which was alleviated after UV/bisulfite treatment. This work provided a meaningful support to potential risk of CBZ intermediates products, which shed light on the future application in eliminating drugs using UV /bisulfite.

Ultrahigh-efficient BiOBr-x%La@y%CNQDs nanocomposites with enhanced generation and separation of photogenerated carriers towards bisphenol A degradation and toxicity reduction

In this study, a series of hierarchical flower-like La-doped BiOBr composites modified with carbon nitride quantum dots (BiOBr-x%La@y%CNQDs) was synthesized using a microwave solvothermal method in combination with a calcination method. It was found that La doping and CNQDs co-decorated with BiOBr showed much better photoreactivity for bisphenol A (BPA) degradation than pure BiOBr. The best degradation and mineralization efficiencies of BPA were 100% and 77% within 12 min at La and CNQDs contents of 1% and 1.25%, respectively. Various characterization results demonstrated that this synergistic effect on BiOBr-1%La@1.25%CNQDs was attributed to its improved light-harvesting properties, enhanced photogenerated electron and holes pairs separation and interfacial charge transfer. Degradation pathways were proposed based on active species analysis, identification of nine intermediates, and density functional theory (DFT) calculations. Furthermore, a bioluminescence assay of the inhibition rate of the luminescent bacterium Vibrio qinghaiensis sp. Q67 showed that BiOBr-1%La@1.25%CNQDs have superior detoxification ability. The present study provides some insight into the design of ultrahigh-efficiency nanojunction photocatalysts with a broadened photoabsorption range and improved separation efficiency of photogenerated carriers to enhance the degradation and detoxification performance of BPA.

Efficient Photodegradation of Eriochrome Black-T by a Trimetallic Magnetic Self-Synthesized Nanophotocatalyst Based on Zn/Au/Fe-Embedded Poly(vinyl alcohol)

This study presents a novel photocatalytic system for photocatalytic degradation of Eriochrome black-T (EBT) dye via green light-emitting diode (LED) light exposure. This photocatalyst is comprised of nanoscale components, i.e., poly(vinyl alcohol) (PVA), magnetic iron oxide nanoparticles (Fe₃O₄ NPs), gold NPs (Au NPs), and zinc oxide nanorods (ZnO NRs), rendering an active high surface area. The most highlighted property from the structural facet is the superparamagnetic behavior of Fe₃O₄ NPs, which provides a facile collection of magnetic photocatalyst NPs from the reaction flask and is successfully recycled eight times without considerable reduction in catalytic behavior. Briefly, the photocatalytic degradation at its highest efficiency reached 51.4% (10 ppm dye solution, 5.0 mL) and 64.75% (8 ppm dye solution, 5.0 mL) utilizing 10 mg of the designed photocatalyst (formulated as Fe₃O₄@PVA-Au/ZnO), a magnetic photocatalytic system under green LED light (7 W, 526 nm) exposure for 60 min. Besides, the photocatalytic degradation mechanism of the EBT dye by the as-prepared photocatalyst was proposed. Based on the obtained results, the presented photocatalytic method was recommended for scaling up and large-scale exploitation for the purification of the water resources.

Highly efficient decontamination of tetracycline and pathogen by a natural product-derived Emodin/HAp photocatalyst

To address the water pollution induced by pharmaceuticals, especially antibiotics, and pathogens, natural product emodin, a traditional Chinese medicine with the characteristic large π-conjugation anthraquinone structure, was used to rationally develop a novel Emodin/HAp photocatalyst by integrating with a thermally stable and recyclable support material hydroxyapatite (HAp) through a simple preparation method. It was found that its photocatalytic activity to generate reactive oxygen species (ROS) was greatly improved due to the migration of photogenerated electrons and holes between emodin and HAp upon visible light irradiation. Thus, this Emodin/HAp photocatalyst not only quickly photodegraded tetracycline with 99.0% removal efficiency but also exhibited complete photodisinfection of pathogenic bacteria Staphylococcus aureus upon visible light irradiation. Therefore, this study offers a new route for the design and preparation of multifunctional photocatalysts using widely available natural products for environmental remediation.

Visible Light-Mediated Photoactivated Sulfur Quantum Dots as Heightened Antibacterial Agents

The need for antimicrobial or antibacterial fabric has increased exponentially in recent past years, especially after the outbreak of the SARS-CoV-2 pandemic. Several studies have been conducted, and the primary focus is the development of simple, automated, performance efficient and cost-efficient fabric for disposable and frequent-use items such as personal protective materials. In this regard, we have explored the light-driven antibacterial activity of water-soluble Sdots for the first time. Sdots are a new class of non-metallic quantum dots of the nanosulfur family having a polymeric sulfur core. These Sdots exhibited excellent antibacterial activity by generating reactive oxygen species under sunlight or visible light. Under 6 h of sunlight irradiation, it was observed that >90% of the bacterial growth was inhibited in the presence of Sdots. Furthermore, low toxic Sdots were employed to develop antibacterial fabric for efficiently cleaning the bacterial infection. The prominent zone of inhibition of up to 9 mm was observed post 12 h incubation of Sdots treated fabric with E. coli in the presence of visible light. Furthermore, the SEM study confirmed the bactericidal effect of these Sdots-treated fabrics. Moreover, this study might help explore the photocatalytic disinfection application of Sdots in diverse locations of interest, Sdots-based photodynamic antimicrobial chemotherapy application, and provide an opportunity to develop Sdots as a visible light photocatalyst for organic transformations and other promising applications.

Catalysing electrowinning of copper from E-waste: A critical review

Smart technologies and digitalisation have increased the consumption of scarce metals that threaten the sustainability of intricated industries. Additionally, the growing streams of waste electrical and electronic equipment (e-waste) are significant hazards to public health and the environment. Thus, there is an escalating need to recover metals from e-waste for sustainable management of metal resources. Hydrometallurgical processing of e-waste, involving copper (Cu) leaching and its subsequent recovery from pregnant leach solution (PLS) via electrowinning, has emerged as an efficient strategy to close the recycling loop. Electrowinning from PLS demonstrated higher Cu recovery efficiency and operational feasibility with a lower reagent use and lesser waste generation. Nevertheless, multiple issues challenged its practical implementation, including selective recovery of Cu from PLS containing mixed metals and high energy consumption. This review (1) identifies the factors affecting Cu electrowinning from PLS; (2) evaluates the composition of lixiviants influencing Cu electrowinning; (3) appraises various catalysts developed for enhancing Cu electrodeposition; and (4) reviews coupled systems that minimised process energy consumption. From the literature review, electrocatalysts are prospective candidates for improving Cu electrowinning as they reduced the cathodic reduction overpotentials, enhanced surface reaction kinetics and increased current efficiency. Other catalysts, including bioelectrocatalysts and photoelectrocatalysts, are applicable for dilute electrolytes with further investigations required to validate their feasibility. The coupled systems, including slurry electrolysis, bioelectrochemical systems and coupled redox fuel cells, minimise process energy requirements by systematically coupling the cathodic reduction reaction with suitable anodic oxidation reactions having thermodynamically low overpotentials. Among these systems, slurry electrolysis utilising a single-step processing of e-waste is feasible for commericalisation though operational challenges must be addressed to improve its sustainability. The other systems require further studies to improve their scalability. It provides an important direction for energy-efficient Cu electrowinning from PLS, ultimately promoting a circular economy for the scarce metal resources.

A facile synthesis of palladium nanoparticles decorated bismuth oxybromide nanostructures with exceptional photo-antimicrobial activities

Assessing the interaction between microbes and nanocatalysts for finding an inclusive, proactive and deep understanding of nanoparticles-based toxicity is vital for discovering their broad range of applications. Palladium based photocatalysts owing to their unique fundamental characteristics and brilliant physicochemical potential have gained immense interest in environment remediation as disinfection system. In the present study, we report synthesis of a novel palladium nanoparticles decorated bismuth oxybromide (Pd/BiOBr) nanostructures using an energy efficient solution-based method, having excellent photocatalytic antibacterial action. The synthesized nanomaterials was thoroughly characterized using various analytical techniques. The photocatalytic antibacterial efficiency of Pd/BiOBr was evaluated against some common pathogenic strains of Gram-positive and Gram-negative bacteria (Pseudomonas fluorescens, Pseudomonas aeruginosa, Escherichia coli, Aeromonas salmonicida, Salmonella typhimurium, Klebsiella pneumoniae, Bacillus subtilis). In our results Pd/BiOBr showed excellent photocatalytic disinfection efficacy with > 99.9% bacterial inactivation. A very low concentration of Pd/BiOBr (0.5 µg/mL) effectively inhibited the bacterial growth in response to just 2 h of visible light irradiation, while 1 µg/mL of Pd/BiOBr completely killed all the tested bacterial strains proving their magnificent bactericidal potential. The developed materials with exceptional antibacterial broad range efficiency can be used in different photocatalytic disinfection systems including water purification systems, biofilm exclusion and combating differential antibiotic resistance.

Molybdenum Modified Sol–Gel Synthesized TiO2 for the Photocatalytic Degradation of Carbamazepine under UV Irradiation

Pharmaceutical CEC compounds are a potential threat to man, animals, and the environment. In this study, a sol–gel-derived TiO2 (SynTiO2) was produced and subsequently sonochemically doped with a 1.5 wt% Mo to obtain the final product (Mo (1.5 wt%)/SynTiO2). The as-prepared materials were characterized for phase structure, surface, and optical properties by XRD, TEM, N2 adsorption–desorption BET isotherm at 77 K, and PSD by BJH applications, FTIR, XPS, and UV-Vis measurements in DRS mode. Estimated average crystallite size, particle size, surface area, pore-volume, pore size, and energy bandgap were 16.10 nm, 24.55 nm, 43.30 m2/g, 0.07 cm3/g, 6.23 nm, and 3.05 eV, respectively, for Mo/SynTiO2. The same structural parameters were also estimated for the unmodified SynTiO2 with respective values of 14.24 nm, 16.02 nm, 133.87 m2/g, 0.08 cm3/g, 2.32 nm, and 3.3 eV. Structurally improved (Mo (1.5 wt%)/SynTiO2) achieved ≈100% carbamazepine (CBZ) degradation after 240 min UV irradiation under natural (unmodified) pH conditions. Effects of initial pH, catalyst dosage, initial pollutant concentration, chemical scavengers, contaminant ions, hydrogen peroxide (H2O2), and humic acid (HA) were also investigated and discussed. The chemical scavenger test was used to propose involved photocatalytic degradation process mechanism of CBZ.

Peroxymonosulfate activated by photocatalytic fuel cell with g-C3N4/BiOI/Ti photoanode to enhance rhodamine B degradation and electricity generation

The development of traditional photocatalytic fuel cell (PFC) is severely hindered by poor visible-light response and limited reaction space. In this study, a visible-light responsive PFC with g-C₃N₄/BiOI/Ti photoanode was proposed and applied to activate peroxymonosulfate (PMS) to degrade rhodamine B. The degradation rate, maximum power density and maximum photocurrent density of the PMS/PFC system were respectively 95.39%, 103.87 μW cm^-2 and 0.62 mA cm^-2, which was respectively 1.28, 2.18, and 1.98 times that of PFC. The excellent performance is attributed to the production of more reactive oxygen species and the extension of the reaction space range after the activation of PMS. The activation pathway of PMS and charge transfer pathway of the photoanode were discussed in detail, and it was proposed that PMS was activated by Z-scheme heterojunction g-C₃N₄/BiOI/Ti photoanode.

Photocatalytic activity study of ZnO modified with nitrogen–sulfur co-doped carbon quantum dots under visible light

Enhanced degradation rate of RhB under visible light by N,S-CQDs-modified ZnO.

Synthesis and Enhanced Light Photocatalytic Activity of Modulating Band BiOBrXI1-X Nanosheets

The photocatalysis technique has been proven to be a promising method to solve environmental pollution in situations of energy shortage, and has been intensively investigated in the field of pollutant degradation. In this work, a band structure-controlled solid solution of BiOBr_XI_1−X (x = 0.00, 0.05, 0.10, 0.15, 0.20, 1.00) with highly efficient light-driven photocatalytic activities was successfully synthesized via simple solvothermal methods. The phase composition, crystal structure, morphology, internal molecular vibration, optical properties, and energy band structure were characterized and analyzed by XRD, SEM, HRTEM, XPS, Raman, and UV Vis DRS. To evaluate the photocatalytic activity of BiOBr_XI_1−X, rhodamine B was selected as an organic pollutant. In particular, BiOBr_0.15I_0.85 displayed significantly enhanced photocatalytic activity by virtue of modulating the energy band position, optimizing redox potentials, and accelerating carrier separation. Moreover, the enhancement mechanism was elucidated on the basis of band structure engineering, which provides ideas for the design of highly active photocatalysts for practical application in the fields of environmental issues and energy conservation.