Relying on the non-radical pathways for selective degradation organic pollutants in Fe and Cu co-doped biochar/peroxymonosulfate system: The roles of Cu, Fe, defect sites and ketonic group

Multifunctional Fe/Cu Dual-Single Atom Nanozymes with Enhanced Peroxidase Activity for Isoniazid Detection and Levofloxacin Degradation

The design of single-atom nanozymes with dual active sites to increase their activity and for the detection and degradation of contaminants is rare and challenging. In this work, a single-atom nanozyme (FeCu-NC) based on a three-dimensional porous Fe/Cu dual active site was developed as a colorimetric sensor for both the quantitative analysis of isoniazid (INH) and the efficient degradation of levofloxacin (LEV). FeCu-NC was synthesized using a salt template and freeze-drying method with a three-dimensional hollow porous structure and dual active sites (Fe-Nx and Cu-Nx). In terms of morphology and structure, FeCu-NC exhibits excellent peroxidase-like activity and catalytic properties. Therefore, a colorimetric sensor was constructed around FeCu-NC for sensitive and rapid quantitative analysis of INH with a linear range of 0.9-10 μM and a detection limit as low as 0.3 μM, and the sensor was successfully applied to the analysis of INH in human urine. In addition, FeCu-NC promoted the efficient degradation of LEV by peroxymonosulfate activation, with a degradation rate of 90.4% for LEV at 30 min. This work sheds new light on the application of single-atom nanozymes to antibiotics for colorimetric sensing and degradation.

Cu/N co-doped biochar activating PMS for selective degrading paracetamol via a non-radical pathway dominated by singlet oxygen and electron transfer

The non-free radical oxidation pathway (PMS-NOPs) of peroxymonosulfate (PMS) holds significant promise for practical wastewater treatment applications, owing to its low oxidation potential, high PMS utilization rate, and robust anti-interference capability in the degradation of pollutants. A novel activator copper nitrogen co-doped porous biochar (Cu-N-BC) with rich defect edges and functional groups was obtained by adding Cu and N to the biochar matrix generated by sodium alginate through pyrolysis in this study. Under the condition of 1 mM PMS, 30 mg/L activator was used to activate PMS and achieve efficient degradation of 10 mg/L paracetamol (PCT) within 15 min, with a high reaction rate constants (kobs) of 0.391 min-1. The activation mechanism of the Cu-N-BC/PMS/PCT system was a non-radical activation pathway with the dominance of singlet oxygen (1O2) and the presence of catalyst-mediated electron transfer. The graphite nitrogen, pyridine nitrogen, and Cu-N coordination introduced by Cu/N co-doping, as well as the carbon skeleton and CO functional group of biochar, were considered active sites that promote the 1O2 generation. The Cu-N-BC/PMS system exhibits strong stability, eco-friendliness, effective mineralization, and interference resistance across diverse pH levels (3-11) and interfering ions, including Cl-, H2PO4-, NO3-, SO42-, and humic acid. Remarkably, it efficiently degrades PCT in tap and lake water, achieving a notable 63.73% TOC mineralization rate, with leached copper ions below 0.02 mg/L. This research introduces a novel method for obtaining metal nitrogen carbon activators and enhances understanding of PMS non-radical activation pathways and active sites.

Unraveling kinetic and synergistic effects during ultrasound-enhanced carbocatalysis for water remediation as a function of ultrasonic frequency

The ability of the ultrasound (US) combined with peroxymonosulfate (PMS), and a carbonaceous material (BC) was evaluated in the degradation of a model pollutant (acetaminophen, ACE). The US/BC/PMS system was compared with other possible systems (US, oxidation by PMS, BC adsorption, BC/PMS, US/PMS, and US/BC. The effect of the ultrasonic frequency (40, 375, and 1135 kHz) on the kinetics and synergy of the ACE removal was evaluated. In the US system, kinetics was favored at 375 kHz due to the increased production of hydroxyl radicals (HO•), but this did not improve in the US/PMS and US/BC systems. However, synergistic and antagonistic effects were observed at the low and high frequencies where the production of radicals is less efficient but there is an activation of PMS through mechanical effects. US/BC/PMS at 40 kHz was the most efficient system obtaining ∼95% ACE removal (40 μM) in the first 10 min of treatment, and high synergy (S = 10.30). This was promoted by disaggregation of the carbonaceous material, increasing the availability of catalytic sites where PMS is activated. The coexistence of free-radical and non-radical pathways was analyzed. Singlet oxygen (1O2) played the dominant role in degradation, while HO• and sulfate radicals (SO4•-), scarcely generated at low frequency, play a minimum role. Performance in hospital wastewater (HWW), urine, and seawater (SW) evidenced the competition of organic matter by BC active sites and reactive species and the removal enhancement when Cl- is present. Besides, toxicity decreased by ∼20% after treatment, being the system effective after three cycles of reuse.

Three dimensional nickel foam carried sea urchin-like copper-cobalt-cerium cathode for enhanced tetracycline wastewater purification in photocatalytic fuel cell

Photocatalytic fuel cells (PFCs) regarded as a potential sustainable technique, have been broadly reported. In this work, the carbon quantum dot-loaded TiO2 photoanode and sea urchin-like CuCoCe ternary metal oxide cathode materials are successfully synthesized and used to construct PFC systems for efficient tetracycline (TC) degradation (45 mg/L) and simultaneous electricity generation. The results demonstrate that the CQDs-modified TiO2 photoanode has improved absorption intensity in both the UV and visible regions, and the photocurrent density at 1.23 V vs RHE reached 1.31 mA cm-2, which is 1.3 times higher than that of the original TiO2 photoanode. The established PFC system achieves the highest removal ratio of 96.9 % for TC in 60 min with a maximum power density of 0.77 mW cm-2. The PFC system can operate efficiently over a wide pH range (3.0-9.0). Furthermore, quenching experiments and ESR spectra show that the main reactive oxygen species in the degradation process are •O2-, 1O2 and •OH. This study provides meaningful way to develop multiple metal oxides as cathode of PFC system for efficient organic pollutant degradation and energy recovery.

Sea Urchin-like NiCo2O4 Catalyst Activated Peroxymonosulfate for Degradation of Phenol: Performance and Mechanism

How to efficiently activate peroxymonosulfate (PMS) in a complex water matrix to degrade organic pollutants still needs greater efforts, and cobalt-based bimetallic nanomaterials are desirable catalysts. In this paper, sea urchin-like NiCo2O4 nanomaterials were successfully prepared and comprehensively characterized for their structural, morphological and chemical properties via techniques, such as X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), among others. The sea urchin-like NiCo2O4 nanomaterials exhibited remarkable catalytic performance in activating PMS to degrade phenol. Within the NiCo2O4/PMS system, the removal rate of phenol (50 mg L-1, 250 mL) reached 100% after 45 min, with a reaction rate constant k of 0.091 min-1, which was 1.4-times higher than that of the monometallic compound Co3O4/PMS system. The outstanding catalytic activity of sea urchin-like NiCo2O4 primarily arises from the synergistic effect between Ni and Co ions. Additionally, a comprehensive analysis of key parameters influencing the catalytic activity of the sea urchin-like NiCo2O4/PMS system, including reaction temperature, initial pH of solution, initial concentration, catalyst and PMS dosages and coexisting anions (HCO3-, Cl-, NO3- and humic acid), was conducted. Cycling experiments show that the material has good chemical stability. Electron paramagnetic resonance (EPR) and quenching experiments verified that both radical activation (SO4•-, •OH, O2•-) and nonradical activation (1O2) are present in the NiCo2O4/PMS system. Finally, the possible degradation pathways in the NiCo2O4/PMS system were proposed based on gas chromatography-mass spectrometry (GC-MS). Favorably, sea urchin-like NiCo2O4-activated PMS is a promising technology for environmental treatment and the remediation of phenol-induced water pollution problems.

FeS and Fe3O4 Co-modified biochar to build a highly resistant advanced oxidation process system for quinclorac degradation in irrigation water

Advanced oxidation processes (AOPs), based on sulfate radical (SO4·-) produced by peroxymonosulfate (PMS), can effectively mineralize refractory organic pollutants. However, the coexistence of anions and natural organic matters in actual wastewater prevents the application of AOPs. A simple one-step method was used to prepare FeS/Fe3O4 co-modified biochar materials (FFB) that could activate PMS to degrade quinclorac (QNC) with a removal rate of 100%, even exhibiting optimum degradation of QNC reached 99.31% in irrigation water, demonstrating excellent anti-interference performance for co-existing anions and natural organic matter. Meanwhile, ecotoxicity analysis showed that the toxicity of degradation intermediates was lower than that of QNC. Characterization results demonstrated the even distribution of FeS and Fe3O4 onto biochar, supplying abundant Fe2+ to activate PMS producing reactive oxygen species (ROS), while the generated Fe3+ after reactive continue to be reduced with sulfur species to promote the cycle of Fe2+/Fe3+. The coexistence of ·OH, SO4·-, 1O2, and O2·- in the FFB/PMS-QNC system suggest the possession of two pathway with free radical and non-free radical pathways to degrade QNC. The density functional theory (DFT) was used to analyze the adsorption sites and adsorption energy of PMS, as well as the differential charge density, which further proved the generation of SO4·-, O2·- and 1O2. In addition, the electrochemical test results showed that electron transfer also played an important role in the degradation of QNC. This study provides a feasible approach for the removal of organic pollutants in actual water.

Atomically Dispersed Fe-N4 Site as a Conductive Bridge Enables Efficient and Stable Activation of Peroxymonosulfate: Active Site Renewal, Anti-Oxidative Capacity, and Pathway Alternation Mechanism

Atomically dispersed metal sites anchored on nitrogen-doped carbonaceous substrates (M-NCs) have emerged as promising alternatives to conventional peroxymonosulfate (PMS) activators; however, the exact contribution of each site still remains elusive. Herein, isolated Fe-N4 active site-decorated three-dimensional NC substrates (FeSA-NC) via a micropore confinement strategy are fabricated to initiate PMS oxidation reaction, achieving a specific activity of 5.16 × 103 L·min-1·g-1 for the degradation of bisphenol A (BPA), which outperforms most of the state-of-the-art single-atom (SA) catalysts. Mechanism inquiry reveals enhanced chemisorption and electron transfer between PMS and FeSA-NC, enabling an inner electron shuttle mechanism in which Fe-N4 serves as a conductive bridge. The Fe-N4 sites reduce the energy barrier for the formation of SO5* and H*, thereby transforming the reaction pathway from directly adjacent electron transfer into reactive oxygen species (ROS)-dominated oxidation. Theoretical calculations and dynamic simulations reveal that the Fe-N4 sites induce facilitated desorption of reaction intermediates (PMS*/BPA*), which collectively contribute to the renewal of active sites and eventually enhance the catalytic durability. This work offers a reasonable interpretation for the important role of the Fe-N4 moiety in altering the activation mechanism and enhancing the antioxidative capacity of NC materials, which fundamentally furnishes theoretical support for SA material design.

Activation of peroxymonosulfate by biochar-supported Fe3O4 derived from oily sludge to enhance the oxidative degradation of tetracycline hydrochloride

Carbon materials used for catalysis in advanced oxidation processes tend to be obtained from cheap and readily available raw materials. We constructed a carbon material, OSC@Fe3O4, by loading Fe3O4 onto the pyrolyzed hazardous waste oily sludge. OSC@Fe3O4 was then used to activate peroxymonosulfate (PMS) for the removal of tetracycline hydrochloride (TTCH) from water. At 298 K, 0.2 g⋅L-1 of catalyst and 0.3 g⋅L-1 of PMS, the reaction rate constant of the OSC@I-2/PMS system reached 0.079 min-1, with a TTCH removal efficiency of 92.6%. The degradation efficiency of TTCH remained at 81% after five cycles. The specific surface area and pore volume of OSC@I-2 were 263.9 m2⋅g-1 and 0.42 cm3⋅g-1, respectively, which improved the porous structure of the carbon material and provided more active points, thus improving the catalytic performance. N and S were doped into the oily sludge carbon due to the presence of N- and S-containing compounds in the raw oily sludge. N and S doping led to more electron-rich sites with higher negative charges in OSC@I-2 and gave the oily sludge carbon a higher affinity to PMS, thereby promoting its ability to activate PMS. Sulfate radicals (SO4•‾) played a dominant role in the degradation of TTCH, with demethylation and the breaking of double bonds being a possible degradation pathway. A biotoxicity test showed that the microbial toxicity of the degradation intermediates was significantly reduced. This work provides a strategy for the application of PMS-based catalysts derived from waste carbon resources.

Synchronous decomplexation and mineralization of copper complexes by activating peroxymonosulfate with magnetic bimetallic biochar derived from municipal sludge

Efficient removal of copper complexes is a challenging issue due to their robust stability and solubility. In this study, CoFe2O4-Co0 loaded sludge-derived biochar (MSBC), a magnetic heterogeneous catalyst, was prepared to activate peroxymonosulfate (PMS) for the decomplexation and mineralization of some typical copper complexes (including Cu(Ⅱ)-EDTA, Cu(Ⅱ)-NTA, Cu(Ⅱ)-citrate, and Cu(Ⅱ)-tartrate). The results showed that abundant cobalt ferrite and cobalt nanoparticles were decorated in the plate-like carbonaceous matrix, making it a higher degree of graphitization, better conductivity and more excellent catalytic activity than the raw biochar. Cu(Ⅱ)-EDTA was chosen as the representative copper complex. Under the optimum condition, the decomplexation and mineralization efficiency of Cu(Ⅱ)-EDTA in MSBC/PMS system were 98% and 68% within 20 min, respectively. The mechanistic investigation confirmed that the activation of PMS by MSBC followed both a radical pathway contributed by SO4•- and •OH and a nonradical pathway contributed by 1O2. In addition, the electron transfer pathway between Cu(Ⅱ)-EDTA and PMS facilitated the decomplexation of Cu(Ⅱ)-EDTA. Jointly, CO, Co0, and the redox cycles of Co(Ⅲ)/Co(Ⅱ) and Fe (Ⅲ)/Fe (Ⅱ) were found to play a critical role in the decomplexation process. Overall, the MSBC/PMS system provides a new strategy for efficient decomplexation and mineralization of copper complexes.

Synergistic enhanced activation of peroxymonosulfate by heterojunction Co3O4-CuO@CN for removal of oxytetracycline: Performance, mechanism, and stability

Metal-organic frameworks (MOFs) as precursors for catalysts has drawn growing attentions. In this study, heterojunction Co3O4-CuO doped carbon materials (noted as Co3O4-CuO@CN) were prepared by direct carbonization of CuCo-MOF in air. It was found that the Co3O4-CuO@CN-2 exhibited excellent catalytic activity with the highest Oxytetracycline (OTC) degradation rate of 0.0902 min-1 at 50 mg/L of Co3O4-CuO@CN-2 dosage, 2.0 mM of PMS and 20 mg/L of OTC, which was 4.25 and 4.96 times that of CuO@CN and Co3O4@CN, respectively. Furthermore, Co3O4-CuO@CN-2 was efficient over a wide pH range (pH 1.9-8.4), and possessed good stability and reusability without OTC degradation decrease after five consecutive uses at pH 7.0. In a comprehensive analysis, the rapid regeneration of Cu(II) and Co(II) is responsible for their excellent catalytic performance, and the p-p heterojunction structure formed between Co3O4 and CuO acts as an intermediary of electron transfer to accelerate PMS decomposition. Moreover, it was interesting to find that Cu rather than Co species played a vital role in the PMS activation. The quenching experiments and electron paramagnetic resonance demonstrated that .OH, SO4•-, and 1O2 were the reactive species responsible for oxidation of OTC and the non-radical pathway triggered by 1O2 was dominant.

Efficient degradation of norfloxacin using a novel biochar-supported CuO/Fe3O4 combined with peroxydisulfate: Insights into enhanced contribution of nonradical pathway

Nonradical persulfate oxidation techniques have evolved as a new contaminated water treatment approach due to its great tolerance to water matrixes. The catalysts of CuO-based composites have received much attention in that aside from SO₄^•-/^•OH radicals, the nonradicals of singlet oxygen (¹O₂) can be also generated during persulfate activation via CuO. However, the issues regarding particles aggregation and metal leaching from the catalysts during the decontamination process remain to be addressed, which could have a remarkable impact on the catalytic degradation of organic pollutants. Accordingly in the present study, a novel biochar-supported bimetallic Fe₃O₄-CuO catalyst (CuFeBC) was facilely developed to activate peroxodisulfate (PDS) for the degradation of norfloxacin (NOR) in aqueous solution. The results showed CuFeBC has a superior stability against metal ions Cu/Fe leaching, and NOR (30 mg L^-1) was degraded at 94.5% within 180 min in the presence of CuFeBC (0.5 g L^-1) and PDS (6 mM) in pH 8.5. The scavenging of reactive oxygen species and electron spin resonance analysis revealed that ¹O₂ dominated the degradation of NOR. Compared with pristine CuO-Fe₃O₄, the interaction between biochar substrate and metal particles could significantly enhance the contribution of the nonradical pathway to NOR degradation from 49.6% to 84.7%. Biochar substrate could efficiently reduce the leaching of metal species from the catalyst, thereby maintaining excellent catalytic activity and lasting reusability of the catalyst. These findings could enlighten new insights into fine-tuning radical/nonradical processes from CuO-based catalysts for the efficient remediation of organic contaminants in polluted water.

Enhanced visible light assisted peroxymonosulfate process by biochar in-situ enriched with γ-Fe2O3 for p-chlorophenol degradation: performance, mechanism and DFT calculation

In this study, a novel γ-Fe₂O₃/biochar (BF_γ) composite by a plant in-situ enrichment and one-step pyrolysis strategy was prepared, which was applied as a photocatalyst to activate peroxymonosulfate (PMS) for the degradation of p-chlorophenol (4-CP) under visible light irradiation (BF_γ/PMS/Vis) system. The characterization results exhibited that γ-Fe₂O₃ with localized carbon doping was evenly embedded in biochar during the pyrolysis. BF_γ exhibited better photoresponse properties than biochar (BC) and γ-Fe₂O₃. The removal efficiency of this system for 4-CP reached 96.41% under optimal conditions. This system showed high removal efficiency with a wide pH range (3.0-13.0) and under conditions of different organic pollutants. It also showed strong resistance to interference with co-existing inorganic ions and humic acid (HA). Electron paramagnetic resonance (EPR) and radical scavenging experiments revealed that the reactive oxygen species (ROS) in this system included SO₄^-·, ·OH, ·O₂^- and ¹O₂. The density functional theoretical (DFT) calculations further revealed the promotion of localized carbon doping in γ-Fe₂O₃ on electron transfer and photoresponse, including C-O bond (d=1.29 Å), C-Fe bond (d=1.80 Å) and band gap value (E_gap < 0.72 eV). This study provides new insights into constructing environmentally-friendly catalysts and the possibility of the solid waste recycling for other wetland plants.

Insight into the Fe-Ni/biochar composite supported three-dimensional electro-Fenton removal of electronic industry wastewater

For the efficient removal of the bio-refractory organic pollutants in the electronic industry wastewater, the Ni-Fe (oxides) modified three-dimension (3D) particle electrode was applied in electro-Fenton system (3D/EF), where iron ions were released from anode and deposited onto algal biochar (ABC) to prepare composite catalyst during reaction process. Firstly, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) analysis were applied to confirm successful fabrication of the 3D particle electrode materials. Secondly, COD removal efficiency could reach about 80%, which was about 20% higher than that in 2D/EF system, under the optimized conditions as 2.0 g/L of Ni-ABC particle electrodes, initial pH of 3, 100 mL/min of aeration intensity and 20 mA/cm² of applied current density. Thirdly, characterized using three-dimensional fluorescence spectroscopy and GC-MS analysis, it seemed that most of the macromolecular substances could be degraded, whereas mono-2-ethylhexyl phthalate (MEHP) was identified as the most abundant and representative compound. Finally, possible degradation pathway of MEHP in 3D/EF system was proposed including dealkylation, cleavage of C-O bond, and demethylation. Therefore, this study provides a new strategy in designing EF system employing bimetal doped biochar composite for an efficient elimination of organic pollutants within electronic industry wastewater.

Covalent organic frameworks@ZIF-67 derived novel nanocomposite catalyst effectively activated peroxymonosulfate to degrade organic pollutants

Metal organic frameworks-Covalent organic frameworks (MOFs-COFs) nanocomposites could improve the catalytic performance. Herein, a novel nanocomposite catalyst (CC@Co₃O₄) derived from MOFs-COFs (COF@ZIF-67) was prepared on peroxymonosulfate (PMS) activation for bisphenol A (BPA) and rhodamine B (RhB) degradation. Owing to the Co species, oxygen vacancy (O_V), surface hydroxyl (-OH), graphite N and ketone groups (C=O), the CC@Co₃O₄ exhibited higher catalytic degradation performance and total organic carbon (TOC) for BPA (93.8% and 22.3%) and RhB (98.2% and 82.5%) with a small quantity of catalyst (0.10 g/L) and low concentration of PMS (0.20 g/L) even without pH adjustment. Sulfate radicals (•SO₄^-), hydroxyl radicals (•OH), single oxygen (¹O₂), superoxide radicals (•O₂^-) and electron transfer process were all involved in the degradation of BPA and RhB. Among them, the degradation of BPA and RhB mainly depended on •O₂^- and ¹O₂, respectively. Meanwhile, the degradation pathways of BPA and RhB were proposed, and the biotoxicity of the degradation products was evaluated by freshwater chlorella. The results illustrated that the degradation products were environmentally friendly to organisms. In addition, the role of COF in the nanocomposites was also studied. The addition of COF remarkably improved the catalytic performance of CC@Co₃O₄ due to the faster electron transfer, more graphite N and C=O. Overall, this work may open the door to the development of COF-based catalysts in the field of water pollutant remediation.

Synthesis of Bimetallic FeCu-MOF and Its Performance as Catalyst of Peroxymonosulfate for Degradation of Methylene Blue

Bimetallic MOFs have recently emerged as promising materials for wastewater treatment based on advanced oxidation processes. Herein, a new bimetallic MOF (FeCu-MOF) was fabricated by hydrothermal process. The structural, morphological, compositional and physicochemical properties of the as-synthesized bimetallic FeCu-MOF were characterized by XRD, FT-IR, SEM, TEM, BET, and XPS. TEM and XPS confirmed the homogeneous distribution of CuO₂ nanoparticles in the as-synthesized materials. The result of wastewater treatment indicated that 100% of MB was removed by 6.0 mM PMS activated with 0.6 g/L of FeCu-MOF in 30 min. The high catalytic performance of FeCu-MOF was probably due to the accelerated electron and mass transfer resulting from the existence of a homogeneous distribution of unsaturated metal sites and an abundant mesoporous structure. The obtained results from the competitive quenching tests demonstrated that sulfate radicals (SO₄^•-) were the major species responsible for MB oxidation. In addition, hydroxyl (·OH) and singlet oxygen (¹O₂) also had a nonnegligible role in the MB removal. Interestingly, the addition of acetate ion (CHCOO^-) promoted the removal of MB while other anions (including NO₂^-, H₂PO₄^-, SO₄^2-, HPO₄^2-, and HCO₃^-) inhibited the MB removal. Furthermore, a possible mechanism based on both heterogeneous and homogeneous activation of PMS was proposed, along with the MB degradation mechanism.

Superoxide radical mediated Mn(III) formation is the key process in the activation of peroxymonosulfate (PMS) by Mn-incorporated bacterial-derived biochar

Biochar was used as a heterogeneous activator for peroxymonosulfate (PMS), and the activation performance strongly depended on the structure, functional groups, and modification of the biochar. In this study, a new type of modified biochar was synthesized by utilizing the Mn(II) adsorption capacity of bacteria. After one-step pyrolysis of Mn(II)-adsorbed bacterial cells at 800 °C, a Mn-incorporated bacterial-derived biochar (Mn-BBC) was successfully produced. It exhibited structural heterogeneity, with MnO located at the surface of the BBC matrix, as shown on the result of SEM and XRD. Compared to BBC, Mn-BBC showed a 10-fold increase (0.0727 min^-1 versus 0.0069 min^-1) of pollutant removal rate. In addition, it also showed anti-interference capacity against common water matrix (except 10 mM CO₃^2-) and great stability/reusability. Chemical quenching, electron spin resonance, and pyrophosphate trapping indicated an indirect but important role of the superoxide, formed during the self-decomposition of PMS. The MnO on Mn-BBC can be oxidized by superoxide to produce surface Mn(III), which then binds to PMS and forms a surface complex. This complex promotes electron transfer from the pollutant to the Mn-BBC, facilitating the oxidation of the contaminants. Overall, this study confirmed the PMS activation capacity and mechanism of Mn-BBC, which expands the application of BBC-based materials derived from metal-adsorbed microbes.

Cu-Doped magnetic loofah biochar for tetracycline degradation via peroxymonosulfate activation

The Cu-doped deactivated magnetic biochar exhibited high PMS activation to degrade TC with a high removal rate of 97.6%.