β-Cyclodextrins incorporated multi-walled carbon nanotubes modified electrode for the voltammetric determination of the pesticide dichlorophen

Solvent-activated 3D-printed electrodes and their electroanalytical potential

This work is a comprehensive study describing the optimization of the solvent-activated carbon-based 3D printed electrodes. Three different conductive filaments were used for the preparation of 3D-printed electrodes. Electrodes treatment with organic solvents, electrochemical characterization, and finally electroanalytical application was performed in a dedicated polyamide-based cell also created using 3D printing. We have investigated the effect of the used solvent (acetone, dichloromethane, dichloroethane, acetonitrile, and tetrahydrofuran), time of activation (from immersion up to 3600 s), and the type of commercially available filament (three different options were studied, each being a formulation of a polylactic acid and conductive carbon material). We have obtained and analysed a significant amount of collected data which cover the solvent-activated carbon-based electrodes surface wettability, microscopic insights into the surface topography analysed with scanning electron microscopy and atomic force microscopy, and finally voltammetric evaluation of the obtained carbon electrodes electrochemical response. All data are tabulated, discussed, and compared to finally provide the superior activation procedure. The electroanalytical performance of the chosen electrode is discussed based on the voltammetric detection of ferrocenemethanol.

Experimental and theoretical study on Fe(VI) oxidative degradation of dichlorophen in water: Kinetics and reaction mechanisms

Dichlorophenol (DCP), a commonly used fungicide and insecticide, is widely found in waters and wastewaters. Herein, the degradation of DCP by Ferrate (Fe(VI)) in different matrices was comprehensively investigated. In pure water, a complete removal of DCP was achieved in 300 s at [Fe(VI)]:[DCP] molar ratio of 2:1. The presence of HA (10 mg L^-1) inhibited DCP degradation to a certain extent. A total of twenty degradation products were identified by HPLC/MS analysis. Based on these products, reaction pathways including the cleavage of C-C bridge bond, hydroxylation, and radical coupling were proposed. These reaction mechanisms were further rationalized by theoretical calculations. The analyses of Wiberg bond orders and transition state indicated that C₇-C₈ bond was the most vulnerable site for cleavage, and C₁₂ site was the most likely site for hydroxyl addition. Mulliken atomic spin densities distribution suggested that self-coupling products was easily generated via C-O-C coupling ways. Finally, the feasibility of applying Fe(VI) to degrade DCP (20 μM) in a municipal wastewater effluent and a lake water was evaluated and verified. The findings in this study are of relevance in designing Fe(VI)-based treatment strategy for chlorine-containing persistent pesticides.

Copper Film Modified Glassy Carbon Electrode and Copper Film with Carbon Nanotubes Modified Screen-Printed Electrode for the Cd(II) Determination

A copper film modified glassy carbon electrode (CuF/GCE) and a novel copper film with carbon nanotubes modified screen-printed electrode (CuF/CN/SPE) for anodic stripping voltammetric measurement of ultratrace levels of Cd(II) are presented. During the development of the research procedure, several main parameters were investigated and optimized. The optimal electroanalytical performance of the working electrodes was achieved in electrolyte 0.1 M HCl and 2 × 10⁻⁴ M Cu(II). The copper film modified glassy carbon electrode exhibited operation in the presence of dissolved oxygen with a calculated limit of detection of 1.7 × 10⁻¹⁰ M and 210 s accumulation time, repeatability with RSD of 4.2% (n = 5). In the case of copper film with carbon nanotubes modified screen-printed electrode limit of detection amounted 1.3 × 10⁻¹⁰ M for accumulation time of 210 s and with RSD of 4.5% (n = 5). The calibration curve has a linear range in the tested concentration of 5 × 10⁻¹⁰–5 × 10⁻⁷ M (r = 0.999) for CuF/GCE and 3 × 10⁻¹⁰–3 × 10⁻⁷ M (r = 0.999) for CuF/CN/SPE with 210 s accumulation time in both cases. The used electrodes enable trace determination of cadmium in different environmental water samples containing organic matrix. The validation of the proposed procedures was carried out through analysis certified reference materials: TM-25.5, SPS-SW1, and SPS-WW1.

Improved Voltammetric Determination of Kynurenine at the Nafion Covered Glassy Carbon Electrode - Application in Samples Delivered from Human Cancer Cells

Nowadays, development of analytical methods responding to a need for rapid and accurate determination of human metabolites is highly desirable. Herein, an electrochemical method employing a Nafion-coated glassy carbon electrode (Nafion/GCE) has been developed for reliable determination of kynurenine (a key tryptophan metabolite) using a differential pulse adsorptive stripping voltammetry. To our knowledge, this is the first analytical method to allow for kynurenine determination at the Nafion-coated electrode. The methodology involves kynurenine pre-concentration in 0.1 M H₂SO₄ in the Nafion film at the potential of +0.5 V and subsequent stripping from the electrode by differential pulse voltammetry. Under optimal conditions, the sensor can detect 5 nM kynurenine (for the accumulation time of 60 seconds), but the limit of detection can be easily lowered to 0.6 nM by prolonging the accumulation time to 600 seconds. The sensor shows sensitivity of 36.25 μAμM⁻¹cm⁻² and 185.50 μAμM⁻¹cm⁻² for the accumulation time of 60 and 600 seconds, respectively. The great advantage of the proposed method is easy sensor preparation, employing drop coating method, high sensitivity, short total analysis time, and no need for sample preparation. The method was validated for linearity, precision, accuracy (using a high-performance liquid chromatography), selectivity (towards tryptophan metabolites and different amino acids), and recovery. The comprehensive microscopic and electrochemical characterization of the Nafion/GCE was also conducted with different methods including atomic force microscopy (AFM), optical profilometry, time-of-flight secondary ion mass spectrometry (TOF-SIMS), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The method has been applied with satisfactory results for determination of kynurenine concentration in a culture medium collected from the human ovarian carcinoma cells SK-OV-3 and to measure IDO enzyme activity in the cancer cell extracts.

A voltammetric sensor based on mixed proton-electron conducting composite including metal-organic framework JUK-2 for determination of citalopram

A voltammetric sensor has been developed based on glassy carbon electrode (GCE) modification with nanocomposite consisting of manganese-based metal-organic framework (JUK-2), multi-walled carbon nanotubes (MWCNTs), and gold nanoparticles (AuNPs) for detection of citalopram (CIT). The composition and morphology of JUK-2-MWCNTs-AuNPs/GCE were characterized by X-ray powder diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), energy dispersion spectroscopy (EDS), and scanning electron microscopy (SEM). The electrochemical properties investigated using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) indicated that the fabricated hybrid material exhibits the properties of mixed ion-electron conductor (MIEC). Using staircase voltammetry (SCV), under optimized conditions, the fabricated sensor shows a linear response in three CIT concentration ranges, 0.05-1.0, 1.0-10.0 and 15.0-115.0 μmol L^-1, with a detection limit of 0.011 μmol L^-1. The JUK-2-MWCNTs-AuNPs/GCE was successfully employed for the determination of CIT in pharmaceutical, environmental waters, and biological samples with satisfactory recoveries (98.6-104.8%).

New frontiers and prospects of metal-organic frameworks for removal, determination, and sensing of pesticides

Pesticides have been widely used in agriculture to control, reduce, and kill insects. Humans are also being using pesticides to control insidious animals in daily life. By these practices, a huge volume of pesticides is introduced to the environment. Despite broad-spectrum applicability, pesticides also have hazardous effects on both humans and animals at high and low concentrations. Long-term exposure to pesticides can cause different diseases, like leukemia, lymphoma, and cancers of the brain, breasts, prostate, testis, and ovaries. Reproductive disorders from pesticides include birth defects, stillbirth, spontaneous abortion, sterility, and infertility. Therefore, the application of determination and treatment methods for pre-concentration and removal of these toxic materials from the environment appears a vital concern. To date, different materials and approaches have been employed for these purposes. Among these approaches, multifunctional metal-organic frameworks (MOFs)-assisted adsorption and determination processes have always been in the spotlight. These facts are due to exclusive properties of MOFs in terms of the crystallinity, large surface area, high chemical, and physical stability, and controllable structure as well as unique features of adsorption and determination process in terms of simple, easy, cheap, available method and ability to use in large and industrial scales. In the present work, we illustrate the exceptional features of MOFs as well as the possible mechanism for the adsorption of pesticides by MOFs. The use of these fantastic materials for pre-concentration and removal of pesticides are extensively explored. In addition, the performance of MOFs was compared with other adsorbents. Finally, the new frontiers and prospects of MOFs for the determination, sensing, and removal of pesticides are presented.

A dual-mode nanoprobe for the determination of parathion methyl based on graphene quantum dots modified silver nanoparticles

We developed a highly sensitive and selective method for double-signal analysis (fluorescence and ultraviolet-visible spectrophotometry) of organophosphorus pesticides (OPs), based on reversible quenching of graphene quantum dots (GQDs; fluorophores) with silver nanoparticles (AgNPs; absorbers). We used acetylcholinesterase to catalytically convert acetylthiocholine into thiocholine. In turn, by competitive binding to the AgNPs, the produced thiocholine displaces AgNPs from the GQDs and thus induces fluorescence recovery. However, OP analytes inhibit the activity of acetylcholinesterase and, in so doing, retain the silver-graphene nanoparticle complex and fluorescence quenching. The degree of quenching is proportional to the concentration of OPs; the detection limit is as low as 0.017 μg/L. The ultraviolet-visible absorption of GQDs/AgNPs at 390 nm decreases-because of AgNP aggregation that occurs after desorption from the GQDs-and the absorbance is linearly proportional to the OP concentration. Our system has good selectivity to substances that are commonly present in water and vegetables. We successfully applied our method to OP analysis in water, apple, and carrot samples.

Sonochemical synthesis and anchoring of zinc oxide on hemin-mediated multiwalled carbon nanotubes-cellulose nanocomposite for ultra-sensitive biosensing of H2O2

In this work, the metal oxide and biopolymer nanocomposites on multiwalled carbon nanotubes (MWCNT) were prepared using a simple sonochemical method. The hexagonal nanorods of zinc oxide (ZnO NR) were synthesized by probe sonication (frequency = 20 kHz, amplitude = 50) method and were integrated on ultrasonically functionalized MWCNT-cellulose nanocrystals (MWCNT-CNC) for the first time. The stable hemin bio-composites also were prepared using the bath sonication (37 kHz of frequency, 150 W of power) method, and was used for the selective and ultrasensitive electrochemical detection of H₂O₂. The UV-Vis spectroscopy studies confirmed the presence of native hemin on MWCNT-CNC/ZnO NR nanocomposite. Cyclic voltammetry studies revealed that an enhanced redox electrochemical behaviour of hemin was observed on hemin immobilised MWCNT-CNC/ZnO NR nanocomposite than that of other hemin modified electrodes. Also, the MWCNT-CNC/ZnO NR/hemin modified SPCE showed 2.3 folds higher electrocatalytic activity with a lower reduction potential (-0.2 V) towards H₂O₂ than that of other investigated hemin modified electrodes including hemin/MWCNT and hemin/CNC-ZnO. The fabricated biosensor displayed a stable amperometric response (-0.2 V vs Ag/AgCl) in the linear concentration of H₂O₂ ranging up to 4183.3 µM with a lower detection limit of 4.0 nM.

Sensors Applied for the Detection of Pesticides and Heavy Metals in Freshwaters

Water is essential for every life living on the planet. However, we are facing a more serious situation such as water pollution since the industrial revolution. Fortunately, many efforts have been done to alleviate/restore water quality in freshwaters. Numerous sensors have been developed to monitor the dynamic change of water quality for ecological, early warning, and protection reasons. In the present review, we briefly introduced the pollution status of two major pollutants, i.e., pesticides and heavy metals, in freshwaters worldwide. Then, we collected data on the sensors applied to detect the two categories of pollutants in freshwaters. Special focuses were given on the sensitivity of sensors indicated by the limit of detection (LOD), sensor types, and applied waterbodies. Our results showed that most of the sensors can be applied for stream and river water. The average LOD was72.53±12.69 ng/ml (n=180) for all pesticides, which is significantly higher than that for heavy metals (65.36±47.51 ng/ml,n=117). However, the LODs of a considerable part of pesticides and heavy metal sensors were higher than the criterion maximum concentration for aquatic life or the maximum contaminant limit concentration for drinking water. For pesticide sensors, the average LODs did not differ among insecticides (63.83±17.42 ng/ml,n=87), herbicides (98.06±23.39 ng/ml,n=71), and fungicides (24.60±14.41 ng/ml,n=22). The LODs that differed among sensor types with biosensors had the highest sensitivity, while electrochemical optical and biooptical sensors showed the lowest sensitivity. The sensitivity of heavy metal sensors varied among heavy metals and sensor types. Most of the sensors were targeted on lead, cadmium, mercury, and copper using electrochemical methods. These results imply that future development of pesticides and heavy metal sensors should (1) enhance the sensitivity to meet the requirements for the protection of aquatic ecosystems and human health and (2) cover more diverse pesticides and heavy metals especially those toxic pollutants that are widely used and frequently been detected in freshwaters (e.g., glyphosate, fungicides, zinc, chromium, and arsenic).

Carboxymethyl-botryosphaeran stabilized carbon nanotubes aqueous dispersion: A new platform design for electrochemical sensing of desloratadine

The polysaccharide carboxymethyl-botryosphaeran (CMB) was used to improve the dispersion of multi-walled carbon nanotubes (MWCNTs) in water. This feature was applied in modifying a glassy carbon electrode (GCE) to construct a sensitive voltammetric sensor for the determination of desloratadine (DESL), a tricyclic antihistamine. The morphology and spectroscopic behavior of the sensor were evaluated. The modified sensor was characterized as homogeneous, and presented a higher electroactive area and a lower charge transfer resistance compared to the unmodified GCE. Using linear sweep voltammetry at 25 mV s^-1, the developed sensor presented a sensitivity of 1.018 μA L μmol^-1 in the linear working range of 1.99-32.9 μmol L^-1, with a detection limit of 0.88 μmol L^-1 of DESL in 0.10 mol L^-1 potassium hydrogen-phosphate solution (pH 8.0). In addition, the sensor showed excellent repeatability with a relative standard deviation of only 1.02% for a sequence of 10 measurements. The sensor was successfully applied in the analysis of pharmaceutical preparations containing DESL, with equivalent results compared to a validated spectrophotometric method at the 95% confidence level. The sensor was also employed in the analysis of a spiked sample of DESL in rat serum.

Analytical methods to analyze pesticides and herbicides

Presented in this paper is an annual review of literatures published in 2018 on topics relating to analytical methods for pesticides and herbicides. According to the different techniques, this review is divided into six sections, including extraction methods; chromatographic or mass spectrometric techniques; electrochemical techniques; spectrophotometric techniques; chemiluminescence and fluorescence methods; and biochemical assays. PRACTITIONER POINTS: Totally 134 relevant research articles are summarized. The review is divided into six parts according to the techniques. Chromatographic and mass spectrometric methods are the most widely used.

Carbon Paste Modified Electrode as Powerful Sensor Approach Determination of Food Contaminants, Drug Ingredients, and Environmental Pollutants: A Review

Background:

Application of electrochemical sensors for analysis of food, biological and water polluting compounds helps to speed up their analysis in the real samples. Electrochemical sensors with low cost, fast response and portable ability are a better choice compared to traditional methods for analysis of electro-active compounds such as HPLC. Therefore, in recent years, many analytical scientists have suggested this type of analytical method for analysis of food, biological compounds and water pollutants.

Objective:

Due to low cost, easy modification and low non-faradic current, the carbon paste electrode is a suitable choice as a working electrode in the electrochemical and especially voltammetric analysis. On the other hand, modification of carbon paste electrode can improve the quality of the sensor for the analysis of electroactive compounds at nanomolar level.

High-performance voltammetric sensor for dichlorophenol based on β-cyclodextrin functionalized boron-doped graphene composite aerogels

2, 2-methylenebis (4-chlorophenol) (dichlorophenol, Dcp) is a priority pollutant that poses a serious health threat to the public. Thus, the sensitive analysis of Dcp is of great significance. Heteroatom-doped carbon nanomaterials modified electrodes have been proven to be good electrocatalysts for electrochemical sensing application. β-cyclodextrin (β-CD) as a signal amplifier has also been utilized in biosensors. Inspired by these, in this study, a new composite of β-CD and three-dimensional (3D) boron-doped graphene aerogels (BGAs/β-CD) has been designed as a high-performance electrochemical sensing platform for Dcp determination. Graphene aerogels possess high specific surface area, large pore volume and good conductivity, which ensure rapid mass transfer and accelerated electron transfer. Besides, boron doping causes uneven charge distribution on the graphene lattice surface, producing a large amount of flowing π electrons, which provide abundant active sites for the catalytic oxidation reaction of Dcp. In addition, Dcp molecules could be captured into β-CD through host-guest recognition, which can effectively amplify the detection signal. Combining the merits of BGAs and β-CD, the BGAs/β-CD based sensor achieved sensitive detection of Dcp. Under optimized experimental conditions, the oxidation currents and the concentration of Dcp had a good linear relationship within 1.0 nM ∼ 21 μM. The detection limit was estimated as 0.33 nM (S/N = 3). This study might provide a new basis for the fabrication of 3D BG-based aerogel architectural material and its application in Dcp detection.

Synthesis of Au nanorod-embedded and graphene oxide-wrapped microporous ZIF-8 with high electrocatalytic activity for the sensing of pesticides

Multifunctional metal-organic framework-based composites display great potentials as electrode materials. Herein, highly dispersed Au nanorods were successfully encapsulated inside the zeolitic imidazolate framework ZIF-8 (AuNRs@ZIF-8) by epitaxial growth or nucleus coalescence. The microporous ZIF-8 shell functions as a protective coating to effectively prevent AuNRs from dissolution, aggregation, and migration during the electrochemical testing, while it provides numerous channels for the mass transfer of reactants to the AuNR surface. The as-synthesized AuNRs@ZIF-8 was then encapsulated in graphene oxide (GO) nanosheets to enhance the chemical resistance of the multicore-shell support, which possesses permanent porosity as well as high specific surface area and hydrophilicity. The excellent electrocatalytic performance of the resulting ternary AuNRs@ZIF-8@GO was demonstrated by the highly sensitive sensing of niclosamide, dichlorophen, carbendazim, and diuron, which outperformed the reported electrocatalysts for these four pesticides. This nanocomposite thus holds great promise as a catalyst for electrochemical sensor fabrication due to its abundant multiple active sites, enhanced catalytic activity, and remarkable stability.

Advances of nanosystems containing cyclodextrins and their applications in pharmaceuticals

For many years, researchers have worked with supramolecular structures involving inclusion complexes with cyclodextrins. These studies have resulted in new commercially available drugs which have been of great benefit. More recently, studies using nanoparticles, including nanosystems containing cyclodextrins, have become a focus of academic research due to the versatility of the systems and their remarkable therapeutic potential. This review focuses on studies published between 2002 and 2018 involving nanosystems containing cyclodextrins. We consider the type of nanosystems, their importance in a health context, the physicochemical techniques used to show the quality of these systems and their potential for the development of novel pharmaceutical formulations. These have been developed in recent studies which have mainly been focusing on basic science with no clinical trials as yet being performed. This is important to note because it means that the studies do not include any toxicity tests. Despite this limitation, the characterization assays performed suggest that these new formulations may have therapeutic potential. However, more research is required to assess the efficacy and safety of these nanosystems.

New Generation of Electrochemical Sensors Based on Multi-Walled Carbon Nanotubes

Multi-walled carbon nanotubes (MWCNT) have provided unprecedented advances in the design of electrochemical sensors. They are composed by sp2 carbon units oriented as multiple concentric tubes of rolled-up graphene, and present remarkable active surface area, chemical inertness, high strength, and low charge-transfer resistance in both aqueous and non-aqueous solutions. MWCNT are very versatile and have been boosting the development of a new generation of electrochemical sensors with application in medicine, pharmacology, food industry, forensic chemistry, and environmental fields. This work highlights the most important synthesis methods and relevant electrochemical properties of MWCNT for the construction of electrochemical sensors, and the numerous configurations and successful applications of these devices. Thousands of studies have been attesting to the exceptional electroanalytical performance of these devices, but there are still questions in MWCNT electrochemistry that deserve more investigation, aiming to provide new outlooks and advances in this field. Additionally, MWCNT-based sensors should be further explored for real industrial applications including for on-line quality control.

Construction of Multiple Switchable Sensors and Logic Gates Based on Carboxylated Multi-Walled Carbon Nanotubes/Poly(N,N-Diethylacrylamide)

In this work, binary hydrogel films based on carboxylated multi-walled carbon nanotubes/poly(N,N-diethylacrylamide) (c-MWCNTs/PDEA) were successfully polymerized and assembled on a glassy carbon (GC) electrode surface. The electroactive drug probes matrine and sophoridine in solution showed reversible thermal-, salt-, methanol- and pH-responsive switchable cyclic voltammetric (CV) behaviors at the film electrodes. The control experiments showed that the pH-responsive property of the system could be ascribed to the drug components of the solutions, whereas the thermal-, salt- and methanol-sensitive behaviors were attributed to the PDEA constituent of the films. The CV signals particularly, of matrine and sophoridine were significantly amplified by the electrocatalysis of c-MWCNTs in the films at 1.02 V and 0.91 V, respectively. Moreover, the addition of esterase, urease, ethyl butyrate, and urea to the solution also changed the pH of the system, and produced similar CV peaks as with dilution by HCl or NaOH. Based on these experiments, a 6-input/5-output logic gate system and 2-to-1 encoder were successfully constructed. The present system may lead to the development of novel types of molecular computing systems.

Synthesis and characterization of the thermally reduced graphene oxide in argon atmosphere, and its application to construct graphene paste electrode as a naptalam electrochemical sensor

New insight into the preparation of sensitive carbon-based electrochemical electrode is provided by examining the properties of thermally reduced graphene oxide (TRGO). In this paper, TRGO was prepared by thermal reduction of graphene oxide (GO) in argon atmosphere, and characterized by Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (TEM), selected area electron diffraction (SAED), and atomic force microscopy (AFM). Results showed that thermal reduction in argon was effective to remove oxygen-containing functional groups in GO, and graphene sheets were obtained. Furthermore, TRGO was used to prepare thermally reduced graphene oxide paste electrode (TRGOPE) which showed excellent conductivity and fast electron transfer kinetics confirmed by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The electrode was applied to determination of the pesticide naptalam (Nap) in square-wave voltammetric (SWV) mode. The corresponding current at approx. +1.0 V increased linearly with the Nap concentration within two linear dynamic ranges (LDR) of 0.1-1.0 μmol L^-1 (LDR₁) and 1.0-10.0 μmol L^-1 (LDR₂). The limits of detection (LOD) and quantification (LOQ) for Nap were calculated as 0.015 μmol L^-1 and 0.051 μmol L^-1, respectively. In comparison to the carbon paste electrode (CPE) the results showed that the TRGOPE possesses advantages in terms of linearity, sensitivity and detectability.