Highly selective detection of p-nitrophenol using fluorescence assay based on boron, nitrogen co-doped carbon dots

Ultra-small water-soluble fluorescent copper nanoclusters for p-nitrophenol detection

Due to the widespread application of p-nitrophenol (p-NP) across various industries, particularly in the pharmaceutical and chemical sectors, it has emerged as a significant environmental contaminant in both soil and water ecosystems. The development of swift and sensitive detection platforms for p-NP is therefore demanding. Herein, a fluorescence sensor based on ultra-small copper nanoclusters with exterior glutathione ligands determined by electrospray ionization mass spectrometry (ESI-MS) as [Cu14(SG)12]+ (denoted as Cu-SG NCs) has been prepared in high efficiency, and shown high selectivity for p-NP detection. The Cu-SG NCs, synthesized via a facile one-pot chemical reduction technique, exhibit emission maxima at 620 nm. Notably, the introduction of p-NP into the nanocluster system causes a significant quenching of the Cu-SG NCs fluorescence. The quenching phenomenon arises predominantly as a result of the inner filter effect (IFE), which stems from the substantial overlap between the UV-Vis absorption spectrum of p-NP and the excitation wavelength of Cu-SG NCs. The developed fluorescence sensor platform demonstrates a wide determination range for p-NP, ranging from 0.04 to 2000 µM, with a detection limit of 30 nM. Additionally, the sensor efficacy was successfully validated in the analysis of actual water samples. The ease of synthesis, excellent optical properties, and low toxicity of Cu-SG NCs represent significant advantages over the reported noble metal nanomaterials and is highly promising for future practical applications.

Nitrophenols in the environment: An update on pretreatment and analysis techniques since 2017

Nitrophenols, a versatile intermediate, have been widely used in leather, medicine, chemical synthesis, and other fields. Because these components are widely applied, they can enter the environment through various routes, leading to many hazards and toxicities. There has been a recent surge in the development of simple, rapid, environmentally friendly, and effective techniques for determining these environmental pollutants. This review provides a comprehensive overview of the latest research progress on the pretreatment and analysis methods of nitrophenols since 2017, with a focus on environmental samples. Pretreatment methods include liquid-liquid extraction, solid-phase extraction, dispersive extraction, and microextraction methods. Analysis methods mainly include liquid chromatography-based methods, gas chromatography-based methods, supercritical fluid chromatography. In addition, this review also discusses and compares the advantages/disadvantages and development prospects of different pretreatment and analysis methods to provide a reference for further research.

Bidirectional hybridized hairpin DNA fluorescent aptasensor based on Au-Pd NPs and CDs for ratiometric detection of AFB1

A novel and simple ratiometric fluorescent aptasensor was developed for the sensitive detection of aflatoxin B1 (AFB1). A hairpin DNA (h-DNA) was independently synthesized as the basic skeleton, and the bidirectional hybridization of h-DNA can increase the load of aptamer and signal probes, thereby realizing signal amplification. The high-efficiency fluorescence resonance energy transfer interaction between gold-palladium nanoparticles (Au-Pd NPs) and the self-synthesized fluorescent probe carbon dots (CDs) was utilized. Moreover, the label-free probe SYBR Green I (SG I) dye was introduced to form a double-signal probe with CDs, and a ratiometric sensor with FCDs/FSG I as a response signal was constructed. The ratio strategy can eliminate the fluctuation of external factors, thus improving the accuracy and reliability of the sensor. The quenching effect of Au-Pd NPs on CDs was 1.4 times that of AuNPs and 3.4 times that of Pd NPs, respectively. In the range 1-100 ng/mL, FCDs/FSG I showed a good linear relationship with the logarithm of the concentration of AFB1, and the limit of detection was as low as 0.07 ng/mL. The sensor was used to detect AFB1 in spiked peanuts and wine samples, and the recovery was between 91 and 115%, indicating that the sensor has high application potential in real sample analysis.

A ratiometric fluorescent probe for simultaneous detection of L-ascorbic acid and alkaline phosphatase activity based on red carbon dots/polydopamine nanocomposite

Herein, efficient red carbon dots (R-CDs) were synthesized by one-step hydrothermal treatment of N-(4-amino phenyl) acetamide and (2,3-difluoro phenyl) boronic acid. The optimal emission peak of R-CDs was at 602 nm (under 520 nm excitation) and the absolute fluorescence quantum yield of R-CDs was 12.9%. Polydopamine, which was formed by the self-polymerization and cyclization of dopamine in alkaline condition, emitted characteristic fluorescence with peak position of 517 nm (under 420 nm excitation) and affected the fluorescence intensity of R-CDs through inner filter effect. L-Ascorbic acid (AA), which was the hydrolysis product of L-ascorbic acid-2-phosphate trisodium salt under the catalytic reaction of alkaline phosphatase (ALP), effectively prevented the polymerization of dopamine. Combined with the ALP-mediated AA production and the AA-mediated polydopamine generation, the ratiometric fluorescence signal of polydopamine with R-CDs was correlated closely with the concentration of both AA and ALP. Under optimal conditions, the detection limits of AA and ALP were 0.28 μM during linear range of 0.5-30 μM and 0.044 U/L with linear range of 0.05-8 U/L, respectively. This ratiometric fluorescence detection platform can efficiently shield the background interference of sophisticated samples by introducing a self-calibration as reference signal in a multi-excitation mode, which can detect AA and ALP in human serum samples with satisfactory results. Such R-CDs/polydopamine nanocomposite provides a steadfast quantitative information and makes R-CDs be excellent candidate for biosensors via combining target recognition strategy.

One-Pot, Optimized Microwave-Assisted Synthesis of Difunctionalized and B-N Co-Doped Carbon Dots: Structural Characterization

In this work, we employed a novel microwave-assisted synthesis method to produce nitrogen and boron co-doped carbon dots (B-N co-doped CDs). To achieve optimal synthesis, we conducted a comprehensive parameter modulation approach, combining various synthesis temperatures, times, and precursor concentrations, while keeping the power constant at 150 W and pH 5. Using maximum fluorescence emission as our response variable, the best conditions were identified as 120 °C, 3 min, and a precursor concentration of 1 mg/mL. Characterization using field emission scanning electron microscopy revealed these CDs to have a spherical morphology with an average size of 10.9 ± 3.38 nm. Further high-resolution transmission electron microscopy showed an interplanar distance of 0.23 nm, which is in line with prior findings of CDs that present a 0.21 nm distance corresponding to the (100) plane of graphite. Optical properties were ascertained through UV-vis absorption, identifying distinct π-π* and n-π* transitions. Fluorescence spectroscopy highlighted an emission peak at 375 nm when excited at 295 nm, achieving a quantum yield of 56.7%. Fourier-transform infrared spectroscopy and Raman spectroscopy analyses confirmed the boronic acid and amine groups' presence, underscoring the graphitic nature of the core and the co-doping of boron and nitrogen. These empirical observations were compared with theoretical investigations through simulated Raman spectra, proposing a potential structure for the CDs. X-ray photoelectron spectroscopy further endorsed the co-doping of nitrogen and boron, along with the detection of the specified functional groups. All these characteristics could lend this nanomaterial to different types of applications such as fluorescent probes for a broad range of analytes and for fluorescent cell imaging.

Highly Efficient Fluorescent Detection of Vitamin B12 Based on the Inner Filter Effect of Dithiol-Functionalized Silver Nanoparticles

We report a fluorescent assay for the determination of vitamin B12 (VB12) based on the inner filter effect (IFE) of 1,3-propanedithiol-functionalized silver nanoparticles (PDT-AgNPs). PDT was simply functionalized on the surface of AgNPs through Ag-thiol interaction, which leads to significantly enhanced fluorescence, with excitation and emission at 360 and 410 nm, respectively, via their thiol-mediated aggregation. Since target VB12 has strong absorption centered at 360 nm, which is almost completely overlapping with the excitation spectra of PDT-AgNPs, the VB12 induced strong quenching of the fluorescence of PDT-AgNPs via IFE. The IFE-based mechanism for the fluorescence quenching of PDT-AgNPs in the presence of VB12 was confirmed by the analyses of Stern-Volmer plots at different temperatures and fluorescence decay curves. The fluorescence-quenching efficiency of PDT-AgNPs was linearly proportional to the concentration of VB12 in a wide range of 1 to 50 μM, with a lower detection limit of 0.5 μM, while preserving excellent selectivity toward target VB12 among possible interfering molecules. Furthermore, the PDT-AgNPs-mediated assay succeeded in quantitatively detecting VB12 in drug tablets, indicating that PDT-AgNPs can serve as an IFE-based fluorescent probe in pharmaceutical preparations by taking advantages of its ease of use, rapidity, and affordability.

Orange Pomace-Derived Fluorescent Carbon Quantum Dots: Detection of Dual Analytes in the Nanomolar Range

Green-emissive carbon quantum dots (CQDs) with exclusive chemosensing aspects were synthesized from orange pomace as a biomass-based precursor via a facile microwave method without using any chemicals. The synthesis of highly fluorescent CQDs with inherent nitrogen was confirmed through X-ray diffraction, X-ray photoelectron, Fourier transform infrared, Raman, and transmission electron microscopic techniques. The average size of the synthesized CQDs was found to be 7.5 nm. These fabricated CQDs displayed excellent photostability, water solubility, and outstanding fluorescent quantum yield, i.e., 54.26%. The synthesized CQDs showed promising results for the detection of Cr⁶⁺ ions and 4-nitrophenol (4-NP). The sensitivity of CQDs toward Cr⁶⁺ and 4-NP was found up to the nanomolar range with the limit of detection values of 59.6 and 14 nM, respectively. Several analytical performances were thoroughly studied for high precision of dual analytes of the proposed nanosensor. Various photophysical parameters of CQDs (quenching efficiency, binding constant, etc.) were analyzed in the presence of dual analytes to gain more insights into the sensing mechanism. The synthesized CQDs exhibited fluorescence quenching toward incrementing the quencher concentration, which was rationalized by the inner filter effect through time-correlated single-photon counting measurements. The CQDs fabricated in the current work exhibited a lower detection limit and a wide linear range through the simple, eco-friendly, and rapid detection of Cr⁶⁺ and 4-NP ions. To evaluate the feasibility of the detection approach, real sample analysis was conducted, demonstrating satisfactory recovery rates and relative standard deviations toward the developed probes. This research paves the way for developing CQDs with superior characteristics utilizing orange pomace (biowaste precursor).

Rambutan seed waste-derived nitrogen-doped carbon dots with l-aspartic acid for the sensing of Congo red dye

In this study, new nitrogen-doped carbon dots (N-CDs) were prepared by utilizing rambutan seed waste and l-aspartic acid as dual precursors (carbon and nitrogen sources) through a hydrothermal treatment method. The N-CDs showed blue emission in solution under UV light irradiation. Their optical and physicochemical properties were examined via UV-vis, TEM, FTIR spectroscopy, SEM, DSC, DTA, TGA, XRD, XPS, Raman spectroscopy, and zeta potential analyses. They showed a strong emission peak at 435 nm and excitation-dependent emission behavior with strong electronic transitions of C[double bond, length as m-dash]C/C[double bond, length as m-dash]O bonds. The N-CDs exhibited high water dispersibility and great optical properties in response to some environmental conditions such as heating temperature, light irradiation, ionic strength, and storage time. They have an average size of 3.07 nm and good thermal stability. Owing to their great properties, they have been used as a fluorescent sensor for Congo red dye. The N-CDs selectively and sensitively detected Congo red dye with a detection limit of 0.035 μM. Moreover, the N-CDs were utilized to detect Congo red in tap and lake water samples. Thus, rambutan seed waste was successfully converted into N-CDs and these functional nanomaterials are promising for use in important applications.

Regulating the Electronic Structure of Cu-Nx Active Sites for Efficient and Durable Oxygen Reduction Catalysis to Improve Microbial Fuel Cell Performance

The efficient and durable oxygen reduction reaction (ORR) catalyst is of great significance to boost power generation and pollutant degradation in microbial fuel cells (MFCs). Although transition metal-nitrogen-codoped carbon materials are an important class of ORR catalysts, copper-nitrogen-codoped carbon is not considered a suitable MFC cathode catalyst due to the insufficient performance and especially instability. Herein, we report a three-dimensional (3D) hierarchical porous copper, nitrogen, and boron codoped carbon (3DHP Cu-N/B-C) catalyst synthesized by the dual template method. The introduced B atom as an electron donor increases the electron density around the Cu-N_x active site, which significantly promotes the efficiency of the ORR process and stabilizes the active site by preventing demetallization. Thus, the 3DHP Cu-N/B-C catalyst exhibited excellent ORR performance with the half-wave potential of 0.83 V (vs reversible hydrogen electrode (RHE)) in a 0.1 M KOH electrolyte and 0.68 V (vs RHE) in a 50 mM PBS electrolyte. Meanwhile, 3DHP Cu-N/B-C had satisfactory stability with 94.16% current retention after 24 h of chronoamperometry test, which is better than that of 20% Pt/C. The MFCs using 3DHP Cu-N/B-C not only showed a maximum power density of up to 760.14 ± 19.03 mW m^-2 but also operating durability of more than 50 days. Moreover, the 16S rDNA sequencing results presented that the 3DHP Cu-N/B-C catalyst had a positive effect on the microbial community of the MFC with more anaerobic electroactive bacteria in the anode biofilm and fewer aerobic bacteria in the cathode biofilm. This study provides a new approach for the development of Cu-based ORR electrocatalysts as well as guidance for the rational design of high-performance MFCs.

Insight into the Modulation of Carbon-Dot Optical Sensing Attributes through a Reduction Pathway

Oxidized/reduced carbon dots (CDs) with tunable optical features have emerged as a new class of CDs having a common "molecular origin" but different fluorescence (FL) behaviors. In the present work, using "banana peel" as a sole carbon source followed by doping with fluorine (F), boron (B), and nitrogen (N) over CDs, banana peel-derived carbon dots (BP-CDs) were synthesized using a well-known hydrothermal synthesis method. Moreover, as-synthesized BP-CDs were further reduced to "rBP-CDs" by NaBH4. At post reduction, the FL performance (i.e., quantum yield) of rBP-CDs were found to be enhanced compared with the BP-CDs, along with variations in excitation and emission wavelengths. Interestingly, the optical sensing attributes of BP-CDs and rBP-CDs were varied, that is, BP-CDs selectively sense "Co2+ with a limit of detection (LOD) value of 180 nM", whereas rBP-CDs detected Co2+ (with an LOD value of 242 nM) as well as Hg2+ (with an LOD value of 190 nM). To the best of our knowledge, this work presents the very first report on the modulation of CDs' sensing behavior after reduction. The modulation in the sensing behavior with the common carbon precursor and reduction paves a new possibility for exploring CDs for different commercial applications.

Glutathione-stabilized copper nanoclusters mediated-inner filter effect for sensitive and selective determination of p-nitrophenol and alkaline phosphatase activity

A simple and highly selective fluorescence biosensor has been exploited for p-nitrophenol (p-NP) and alkaline phosphatase (ALP) activity detection based on the glutathione-stabilized copper nanoclusters (GSH-CuNCs) mediated-inner filter effect (IFE). The GSH-CuNCs were prepared by employing GSH as stabilizer and ascorbic acid (AA) as reductant. The obtained GSH-CuNCs exhibited a strong blue fluorescence emission at 420 nm with an excitation wavelength of 365 nm, which overlapped largely with the absorption spectra of p-nitrophenol (p-NP). Therefore, the luminescence of GSH-CuNCs could be quenched by p-NP through inner filter effect. In addition, ALP catalyzed the substrate p-nitrophenyl phosphate (p-NPP) to form p-nitrophenol (p-NP), which also leading to the fluorescence quenching of GSH-CuNCs. The fluorescent strategy was realized for the sensitive determination of p-NP and ALP activity with the promising limit of detection of 20 nM (for p-NP) and 0.003 mU⋅mL^-1 (for ALP). Furthermore, the method could be applied to detect the p-NP content in river water samples and ALP activity in human serum samples.

A convenient fluorescence sensor of tetracycline based on B, N codoped carbon dots/polymer composite film

A convenient fluorescence sensor of tetracycline (TC) was constructed based on carbon dots (CDs) and polyvinyl alcohol (PVA) hydrogel film. The immobilization of CDs in PVA carrier can stabilize the fluorescence of CDs by inhibiting the fluorescence quench due to the aggregation of CDs with time. CDs were prepared by a hydrothermal method. CDs showed bright blue fluorescence with the quantum yield of 0.35. The fluorescence of CDs was quenched by TC owing to the inner filter effect. The linear range for TC detection was 0-350 µM and the limit of detection was 0.17 µM. To test conveniently, PVA film was employed to upload CDs. Therefore, a novel sensor for TC was constructed in a visual mode. By comparison with the most of previous works, the present method displayed higher sensitivity and better selectivity. The results suggest that the present sensor has potential applications in the real-time detection of TC in food analysis.

Simultaneous electrochemical determination of nitrophenol isomers based on macroporous carbon functionalized with amino-bridged covalent organic polycalix[4]arenes

A glassy carbon electrode (GCE) modified by a hybrid, macroporous carbon (MPC) functionalized with triazine bridged covalent organic polycalix[4]arenes (CalCOP) (CalCOP-MPC), has been fabricated and utilized for simultaneous detection of nitrophenols (NP). The obtained CalCOP-MPC were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), which confirmed that MPC had functionalized with CalCOP successfully. Benefiting from the synergistic supramolecular effect of macrocyclic receptor of CalCOP and the excellent electrical properties of MPC, the anodic peaks of o-nitrophenol (o-NP), m-nitrophenol (m-NP), and p-nitrophenol (p-NP) in their mixture can be well separated by the prepared electrode. Differential pulse voltammetry (DPV) measurements at CalCOP-MPC/GCE revealed that the linear ranges of NP isomers were all 1-400 μM, and the detection limit limits were 0.383 μM, 0.122 μM, and 0.212 μM for o-NP, m-NP, and p-NP, respectively. Moreover, the prepared modified electrodes showed a relatively good selectivity and stability, implying the prospect for detecting NP in real environmental samples.

An optical sensing system with ratiometric and turn-off dual-mode of CDs@MnO2 nanosheets for the determination of H2O2 and glucose based on a combination of first-order scattering, fluorescence, and second-order scattering

The optical sensor with ratiometric and turn-off dual modes is constructed to detect H₂O₂ and glucose based on blue fluorescent carbon dots (CDs) and MnO₂ nanosheets with great ability of fluorescence quenching and scattering. Employing CDs@MnO₂ nanosheets nanocomposite as the probe, H₂O₂ is detected by simultaneously collecting first-order scattering (FOS, 353.5 nm), fluorescence (440 nm), and second-order scattering (SOS, 710 nm) under the excitation of 350 nm. H₂O₂ with strong oxidation property can etch the lamellar structure of MnO₂ nanosheets into nano-fragments, which made the fluorescence of CDs in the system recover and the scattering intensity (FOS and SOS) of the system decrease significantly. Therefore, the optical sensor combined FOS and fluorescence signals in ratiometric mode, and SOS signal in turn-off mode to realize sensitive determination of H₂O₂. The linear ranges of ratiometric mode and turn-off mode for H₂O₂ detection were 0.2-40 and 0.2-15 μM, respectively. And the limits of detection (LODs) of two modes were 73 and 104 nM, respectively. Furthermore, the sensor was also successfully applied to the detection of glucose which can react to produce H₂O₂. Satisfactorily, the LODs of this sensor for glucose detection were 95 and 113 nM for ratiometric mode and turn-off mode, respectively. This work not only provides a new method for the accurate detection of H₂O₂ and glucose, but also extends a new idea for the study of the combination of scattering and fluorescence.

Fabrication of nitrogen-enriched carbon dots with green fluorescence for enzyme-free detection of uric acid

Based on the fact that UA directly quenched the green fluorescence of NCDs prepared at RT, a non-invasive sensor was developed.

Fluorescent polydopamine based molecularly imprinted sensor for ultrafast and selective detection of p-nitrophenol in drinking water

A highly effective fluorescent molecularly imprinted sensor (F-PDA-MIS) based on fluorescent polydopamine (F-PDA) was successfully synthesized for selective and ultrafast detection of p-nitrophenol (P-NP) in drinking water. F-PDA with abundant surface functional groups has been artfully modified to firstly serve as both fluorescent monomer and functional monomer in the synthesis of a uniform luminous F-PDA-MIS, which can greatly improve the detection efficiency. As expected, F-PDA-MIS had an obvious emission wavelength of 535 nm with the optimal excitation wavelength at 400 nm. Specially, F-PDA-MIS could detect P-NP in the range 100 to 1100 nM with much lower detection limit of 24.2 nM within 120 s compared with other conventional imprinted fluorescent sensors based on pure quantum dots (QDs) or dyes. This excellent test phenomenon is mainly ascribed to the rapid electron transfer between F-PDA and P-NP. Satisfactory recovery of 98.0-104% for mineral water and 98.6-106% for boiling water were obtained with relative standard deviations (RSDs) of 2.7-3.4% and 2.6-3.5% respectively. The detection reliability of F-PDA-MIS was verified by the comparison with high-performance liquid chromatography (HPLC-UV). Consequently, F-PDA as a fluorescence functional monomer has been shown to be a possible strategy to effectively improve the detection limit and shorten response time of the target determination in water..

Sulfur-doped carbon dots@polydopamine-functionalized magnetic silver nanocubes for dual-modality detection of norovirus

Synergistic dual-mode optical platforms are up-and-coming detection tools in the diagnosis and management of infectious diseases. Here, novel dual-modality fluorescence (FL) and surface-enhanced Raman scattering (SERS) techniques have been integrated into a single probe for the rapid and ultrasensitive detection of norovirus (NoV). The developed FL-SER-based biosensor relies on the dual-signal enhancements of newly synthesized sulfur-doped agar-derived carbon dots (S-agCDs). The antigen-antibody immunoreaction results in forming a core-satellite immunocomplex between anti-NoV antibody-conjugated S-agCDs and polydopamine-functionalized magnetic silver nanocubes [poly (dop)-MNPs-Ag NCs]. By deploying an immunomagnetic enrichment protocol and performing the SERS modality on a single-layer graphene substrate, norovirus-like particles (NoV-LPs) were detected across a wide range of 1 fg mL^-1 - 10 ng mL^-1 with an excellent limit of detection of 0.1 fg mL^-1. The combined advantage of the dual-signaling properties of the biosensor was demonstrated using FL confocal imaging for "hotspots" tracking prior to SERS detection of clinical NoV in fecal specimen down to ⁓10 RNA copies mL^-1. The proposed dual-modality biosensor's performance increases the prospect of a rapid and low-cost sensitive NoV detection and surveillance option for public health.

Cuttlefish ink-based N and S co-doped carbon quantum dots as a fluorescent sensor for highly sensitive and selective para-nitrophenol detection

Para-nitrophenol (PNP) is an important raw material for organic synthesis and its extensive use has produced a series of environmental problems. Here, we develop a highly sensitive and selective fluorescent detection method for PNP with cuttlefish ink-based carbon quantum dots (CQDs). The cuttlefish ink, which is rich in eumelanin, is utilized as the only precursor to synthesize the CQDs via a one-step hydrothermal method. The resultant CQDs were co-doped with nitrogen and sulfur and exhibited excellent fluorescence properties. Two optimal emissions can be observed at the excitation/emission wavelengths of 320/385 nm and 390/465 nm, respectively. In the presence of PNP, the two emissions are remarkably quenched. PNP can be measured in the linear detection concentration range of 1.25-50 μM (Em = 385 nm and R² = 0.9884) or 1.25-27.5 μM (Em = 465 nm and R² = 0.9818) with a detection limit of 0.05 μM. Significantly, it is found that a much wider linear detection range of 0.05-125 μM with a lower detection limit of 0.039 μM (3σ/k) can be achieved when log(I_{385 nm} + I_{465 nm}) was utilized to quantify PNP. The investigations of the sensing mechanism suggested that the inner filter effect and photoinduced electron transfer of PNP and N,S-CQDs leads to fluorescence quenching. The sensing method is successfully applied for PNP detection in real water samples with satisfactory recoveries (91.18-103.14%). A new sustainable waste-prevention strategy of cuttlefish ink and a feasible alternative to PNP detection methods is provided in this article.

Naproxen release aspect from boron-doped carbon nanodots as a bifunctional agent in cancer therapy

In this present study, boron-carbon nanodots were synthesized by the hydrothermal method. Boron-carbon nanodots were prepared by varying the concentration ratios of boronic acid and citric acid: 1 : 25, 2 : 1, and 25 : 1, respectively. The precursors were then poured into a Teflon autoclave and heated at 240° for 4 h. This research aims to synthesise and evaluate the potential of boron-carbon nanodots as a bioimaging agent and naproxen delivery carrier. An X-ray diffractogram showed that the boron-carbon nanodots were amorphous. To analyse the functional groups, FTIR and XPS analysis was carried out. Spectrofluorometric analysis (λ ex 320 nm) showed that the formulation of boron-carbon nanodots 2 : 1 (BCD 2 : 1) has the most ideal fluorescent properties at λ em 453 nm, whereas UV-vis analysis showed λ max at 223 nm, with a quantum yield of 52.29%. A confocal laser scanning micrograph and toxicity test (MTT assays) showed that boron-carbon nanodots delivered naproxen efficiently with loading amount and loading efficiency of naproxen 28% and 65%, respectively. Furthermore, it induced an anticancer effect in HeLa cells. This result indicated that boron-carbon nanodots can be used as a bioimaging agent and naproxen delivery carrier.

Structure and Interface Modification of Carbon Dots for Electrochemical Energy Application

Carbon dots (CDs) as new nanomaterials have attracted much attention in recent years due to their unique characteristics. Notably, structure and interface modification (carbon core, edge, defects, and functional groups) of CDs have been considered as valid methods to regulate their properties, which contain electron transfer effect, electrochemical activity, fluorescence luminescent, and so on. Additionally, CDs with ultrasmall size, excellent dispersibility, high specific surface area, and abundant functional groups can guarantee positive and extraordinary effects in electrical energy storage and conversion. Therefore, CDs are used to couple with other materials by constructing a special interface structure to enhance their properties. Here, diverse structural and interfacial modifications of CDs with various heteroatoms and synergy effects are systematically analyzed. And not only several main syntheses of CDs-based composites (CDs/X) are summarized but also the merit and demerit of CDs/X in electrical energy storage are discussed. Finally, the applications of CDs/X in energy storage devices (supercapacitors, batteries) and electrocatalysts for practical applications are discussed. This review mainly provides a comprehensive summary and future prospect for synthesis, modification, and electrochemical applications of CDs.

Side-Chain Type Polysulfates: Their Synthesis, AIE Properties and Applications for p-Nitrophenol Detection in Water

Two small molecular monomers, ph-TPE and ph-TPE-CN, and their homopolymers Poly (ph-TPE) and Poly (ph-TPE-CN) containing tetra phenylethylene and sulfate structures, were synthesized by a sulfur (VI) fluorine exchange click reaction (SuFEx) and radical polymerization. All the monomers and polymers exhibit a typical aggregation-induced emission (AIE) effect both in the solid state and aggregated state. Moreover, based on the intermolecular charge transfer (ICT) effect between the tetra phenylethylene chromophore and p-nitrophenol, both polymers could be used for the selective detection of p-nitrophenol. The detection limit and reactivity coefficient of Poly (ph-TPE) are 0.081 μM and 5.15×10⁴  M^-1 , respectively, whereas the detection limit and reactivity coefficient of Poly (ph-TPE-CN) are 0.077 μM and 1.81×10⁴  M^-1 , respectively. This can be attributed to the greater sensitivity of Poly (ph-TPE-CN) to p-nitrophenol than that of Poly (ph-TPE). This work provides a new methodology for the preparation and broadening application of side-chain type AIE-active polysulfate fluorescent probes.

Highly Sensitive and Selective Eco-Toxic 4-Nitrophenol Chemical Sensor Based on Ag-Doped ZnO Nanoflowers Decorated with Nanosheets

Herein, we have developed a novel sensing electrode to detect the eco-toxic 4-nitrophenol (4-NP). Ag-doped-ZnO nanoflowers were synthesized by facile hydrothermal method and examined by several characterization techniques in order to understand the morphology, crystal structure, composition, and surface properties. Morphological results were confirmed by the formation of Ag-doped ZnO nanoflowers decorated with nanosheets. Ag-doped ZnO/glassy carbon electrode (GCE) electrode-material-matrix was used for electrochemical sensing of toxic 4-NP. Under optimized conditions, Ag-doped ZnO/GCE modified electrode exhibits high-sensitivity and selectivity compared to the bare GCE electrode. The Ag-doped ZnO/GCE modified electrode exhibits high electrocatalytic oxidation towards 4-NP. Anodic peak current of 4-NP is increased linearly by increasing the concentration of nitrophenol. Additionally, Ag-doped ZnO/GCE shows a wide range of sensitivity from 10 µM to 500 µM, and a linear calibration plot with a good detection limit of 3 µM (S/N = 3). The proposed Ag-doped ZnO/GCE modified electrode showed high sensing stability. In addition, the oxidation mechanism was studied. The obtained results revealed that the Ag-ZnO/GCE electrode could be the promising sensing electrode for 4-NP sensing.

Carbon dots for ratiometric fluorescence detection of morin

The B,N dual-doped carbon dots (B,N-CDs) for ratiometric fluorescence detection the morin were prepared from sodium tetraborate and polyethyleneimine through the single-step hydrothermal method. The B,N-CDs exhibited the optimum excitation and emission wavelength at 340 nm and 467 nm, respectively. Interestingly, the intensities of emission peak at 467 nm of B,N-CDs reduced meanwhile a new peak emerged at 560 nm with the continuous addition of morin, which revealed the ratio fluorescence characteristic between F_560nm/F_467nm and morin concentration with the linearity range and detection limit of 14.5-32.5 μmol/L and 0.3 μmol/L (S/N = 3), respectively. The interference of common antibiotics and remedies could be ignored when the concentration of morin was detected by the B,N-CDs, which demonstrating the outstanding selectivity. Furthermore, the proposed fluorescence method is used to detect morin in urine with recoveries are 99.8-104.5%. The results of this research indicate the feasibility and practicality of B,N-CDs as an effective fluorescent probe for the determination of morin.

Synthesis and modification of carbon dots for advanced biosensing application

There has been an explosion of interest in the use of nanomaterials for biosensing applications, and carbonaceous nanomaterials in particular are at the forefront of this explosion. Carbon dots (CDs), a new type of carbon material, have attracted extensive attention due to their fascinating properties, such as small particle size, tunable optical properties, good conductivity, low cytotoxicity, and good biocompatibility. These properties have enabled them to be highly promising candidates for the fabrication of various high-performance biosensors. In this review, we summarize the top-down and bottom-up synthesis routes of CDs, highlight their modification strategies, and discuss their applications in the fields of photoluminescence biosensors, electrochemiluminescence biosensors, chemiluminescence biosensors, electrochemical biosensors and fluorescence biosensors. In addition, the challenges and future prospects of the application of CDs for biosensors are also proposed.

Enhanced photocatalytic performance and reusability of N-doped carbon dots/zinc oxide hybrid nanostructures

We report the fabrication of nitrogen-doped carbon dots-zinc oxide hybrid (NCDs-ZnO) nanostructures utilizing simple chemical procedures. The role of NCDs in ZnO nanostructured matrix has been analyzed through XRD, SEM, FTIR and PL characterization techniques. The introduction of NCDs was found to modify not only their aspect ratio, observed by a reduction in the preferredc-axis growth compared to thea- andb-axis, but also induced an additional emission around 441 nm, which is typical of NCDs. The hybrid nanostructures were utilized as catalyst for methylene blue dye degradation showing a 95% degradation after 2 h of UV irradiation in comparison to the ∼70% degradation obtained by utilizing pristine ZnO, while the dye half-life (t_1/2) was reduced by ∼65% by utilizing NCDs-ZnO hybrid nanostructures when compared to the pristine ZnO. The reusability of the fabricated hybrid structures was tested up to eight times with no significant loss in their photocatalytic performance (>90%). The stability of the hybrid structures was verified through Z-potential measurements prior and after reutilization. Excellent reusability and simple processing presented by NCDs-ZnO hybrid nanostructures makes them promising for industrial level photocatalyst for the waste water treatment.

Detection of sialic acid using boronic-acid-functionalized metal organic framework UiO-66-NH2@B(OH)2

Sialic acid (SA) is a crucial component of glycoproteins and glycolipids on the cellular membrane, which is essential for maintaining the function of cell membranes, such as cell recognition and communication. Simultaneously, sialic acid plays a significant role in many physiological and pathological processes. Hence, it is urgent to develop a simple and sensitive strategy for determining sialic acid. In this work, a new metal-organic framework called UiO-66-NH₂@B(OH)₂ has been designed and synthesized for the recognition and detection of sialic acid. The boronic acid functional group in UiO-66-NH₂@B(OH)₂ can bind to a diol moiety of the glycerol side chain of sialic acid, which will attenuate or even quench the fluorescence of UiO-66-NH₂@B(OH)₂, thus opening a new road to detect sialic acid. Based on the measurement results, sialic acid can be quantitatively measured in a linear range of 0.05-2.5 mmoL/L with the UiO-66-NH₂@B(OH)₂ probe. The detection limit of sialic acid is as low as 0.025 mmol/L. Furthermore, the boronic-acid functionalized probe UiO-66-NH₂@B(OH)₂ displays high sensitivity and high selectivity to recognize the sialic acid in mouse serum samples. Therefore, the developed UiO-66-NH₂@B(OH)₂ can be used as a promising probe to identify and detect sialic acid in the practical application.

Surface-tuned hierarchical ɤ-Fe2O3-N-rGO nanohydrogel for efficient catalytic removal and electrochemical sensing of toxic nitro compounds

4- Nitrophenol (4-NP) is a top rated hazardous environmental pollutant and secondary explosive chemicals. For the sake of ecology and environment safety, the catalytic reduction and detection of 4-NP is highly important. In this work, ɤ-Fe₂O₃-nitrogen doped rGO (ɤ-Fe₂O₃-N-rGO) nanohydrogel was synthesized by green hydrothermal method. The morphology and phase purity of prepared ɤ-Fe₂O₃-N-rGO nanohydrogel were confirmed by various analytical (SEM, TEM, XRD, and XPS) and electrochemical techniques. The morphological structure of ɤ-Fe₂O₃-N-rGO nanohydrogel confirmed that the nanocrystals are well covered over the 2D N-rGO layer. Further, ɤ-Fe₂O₃-N-rGO nanohydrogel was applied for the catalytic reduction and electrochemical detection of ecotoxic 4-NP. A low cost, ɤ-Fe₂O₃-N-rGO nanohydrogel displayed an excellent catalytic activity, high recyclability (>5 cycles) and high conversion efficiency of 4-NP to 4-Aminophenol (4-AP). In addition, ɤ-Fe₂O₃-N-rGO nanohydrogel modified GCE displayed a wide linear sensing range (0.1-1000 μM), and a low detection limit (LOD) of 0.1 μM with excellent sensitivity, high selectivity (<1.2%) and good stability (>4 weeks). The developed sensor electrode shows the low reduction potential of -0.3 V and -0.60 V for the determination of 4-NP. The proposed ɤ-Fe₂O₃-N-rGO nanohydrogel is promising catalyst for the detection and removal of toxic aromatic nitro compounds in real site applications.

Determination of l-theanine in tea water using fluorescence-visualized paper-based sensors based on CdTe quantum dots/corn carbon dots and nano-porphyrin with chemometrics

BACKGROUND

The quality of tea is influenced by numerous factors, especially l-theanine, which is one of the important markers used to evaluate the sweetness and freshness of tea. Sensitive, rapid, and accurate detection of l-theanine is therefore useful to identify the grade and quality of tea.

RESULTS

A high-sensitivity, paper-based fluorescent sensor combined with chemometrics was established to detect l-theanine in tea water based on CdTe quantum dots / corn carbon dots and nano tetra pyridel-porphine zinc (ZnTPyP). To verify the reliability of this method, fluorescence spectra and fluorescence-visualized paper-based sensors were compared. The fluorescence spectrum method demonstrated a linear range of 1 to 10 000 nmol L^-1 and a limit of detection (LOD) of 0.19 nmol L^-1 . In the fluorescence-visualized paper-based sensors there was a linear range of 10-1000 nmol L^-1 , and the LOD was 10 nmol L^-1 . Partial least squares discriminant analysis (PLSDA) and partial least squares regression analysis (PLSR) were used successfully to determine l-theanine accurately in tea water with this approach. The accuracy of the PLSDA model was 100% both in the training set and the predicting set, and the correlation coefficient between the actual concentration and the predicted concentration was greater than 0.9997 in the PLSR model.

CONCLUSION

This fluorescence-visualized paper-based sensor, combined with chemometrics, could be applied efficiently to the practical analysis of tea water samples, which provides a new idea to ensure the flavor and quality of tea. © 2020 Society of Chemical Industry.

Serratia marcescens-derived fluorescent carbon dots as a platform toward multi-mode bioimaging and detection of p-nitrophenol

Carbon dots (CDs) have excellent application prospects in various fields such as fluorescent dyes, but expanding their application, especially in bioimaging and the detection of organic pollutants, is still a major research objective. In this study, fluorescent CDs were successfully synthesized via the hydrothermal method using Serratia marcescens KMR-3. The platform based on CDs-KMR3 exhibited excellent stability, good biocompatibility, and low biotoxicity, and can be effectively applied to the imaging of bacteria, fungi, plant cells, protozoa and mammalian cells, and can specifically stain the membranes of all tested cells. In this study, for the first time, bacteria-derived CDs were used to image the representative species of organisms ranging from lower-order to higher-order organisms, thereby proving the feasibility of the application of CDs in the fluorescence imaging of Paramecium caudatum. Additionally, CDs-KMR3 can rapidly diffuse into all the parts of the leaf through diffusion into the veins and intercellular interstitium in response to the induction of transpiration. Moreover, the data illustrate that CDs-KMR3 are likely to enter the digestive tracts of microworms by ingestion through the oral cavity and pharynx, and spread to the pseudocoelom and somatic cells, and finally to be excreted from microworms through the anus. Furthermore, this platform can be utilized as fluorescent probes for the rapid and highly selective detection of p-nitrophenol (p-NP). Moreover, this study contributed to the increased application of bacteria-derived CDs in bioimaging and detection of p-NP.

Spectrophotometric Determination of p-Nitrophenol under ENP Interference

Engineered nanoparticles (ENPs) have been widely developed in various fields in recent years, resulting in an increasing occurrence of nanoparticles in the natural environment. However, the tiny substances have created unexpected confusion in environmental sample testing due to the negative nanoeffect of ENPs. In this paper, a novel technique of spectrophotometric determination of p-nitrophenol (PNP) was developed under the interfering impact of nano-Fe(OH)₃, widely distributed in the natural environment as a typical example of ENPs. Because of the strong absorption at the two characteristic peaks of PNP, namely, 317 nm and 400 nm, nano-Fe(OH)₃ interfered with the colorimetric determination of PNP. Thus, the developed testing method, with HCl acidification at 60°C and ascorbic acid (AA) masking FeCl₃, was proposed and successfully realized the accurate determination of PNP in water samples by ultraviolet spectrophotometry with 317 nm as the absorption wavelength. The final colorimetric system of 5% HCl, 10% CH₃OH, and 1% ascorbic acid was confirmed by optimized batch experiments, and the optimum condition of acidification pretreatment was heating at 60°C for 20 min. Further results demonstrated that the proposed novel method had good accuracy and reproducibility even in high-salinity natural water bodies such as groundwater and surface water. The testing technique presented in this paper provided an interesting and useful tool for problem solving of PNP surveys under ENPs' interference and practically supported water quality assessment for a better environment.

Nitrogen, silicon co-doped carbon dots as the fluorescence nanoprobe for trace p-nitrophenol detection based on inner filter effect

P-nitrophenol (PNP) has been widely applied to industry processing for many purposes, but the persistence and toxicity of residuum may pose risks to human health. To analyze PNP in industrial and agricultural wastewater, a versatile fluorescent probe sensing platform was proposed. In this work, we devised a fluorescence approach that utilized nitrogen, silicon co-doped carbon dots (N,Si-CDs) to monitor PNP originating from the inner filter effect (IFE). The N,Si-CDs were generated in a one-step hydrothermal synthesis, and which possessed outstanding fluorescence signal and water-dispersity. Emission at 441 nm was monitored with excitation at 360 nm using a common spectrofluorometer. The method achieved an exceptionally low limit of detection (LOD) of 0.011 μM. Furthermore, this method not only eliminates the interference from metal ions and acid ions, but also provides a potential application prospect for N,Si-CDs in the field of water monitoring. Analysis of tap and lake water led to 93.30-106.30% recoveries and <1% relative standard deviation at 2.5-25 μM PNP concentrations.

Quantum dots as nanosensors for detection of toxics: a literature review

Great advances have been made in sensor-based methods for chemical analysis owing to their high sensitivity, selectivity, less testing time, and minimal usage of chemical reagents. Quantum Dots (QDs) having excellent optical properties have been thoroughly explored for variety of scientific applications wherein light plays an important role. In recent years, there have been an increasing number of publications on the applications of QDs as photoluminescent nanosensors for the detection of chemicals and biomolecules. However, there has been hardly any publication describing the use of QDs in the detection of various toxic chemicals at one place. Hence, a literature survey has been made on the applications of QDs as chemosensors for the detection of gaseous, anionic, phenolic, metallic, drug-overdose, and pesticide poison so as to open a new perspective towards the role of sensors in analytical toxicology. In this review, the QD-based analysis of biospecimens for poison detection in clinical and forensic toxicology laboratories is highlighted.

Redox induced dual-signal optical sensor of carbon dots/MnO2 nanosheets based on fluorescence and second-order scattering for the detection of ascorbic acid

In order to detect ascorbic acid (AA) sensitively, a dual-signal optical sensor of a nanosystem with carbon dots (CDs)/MnO₂ nanosheets based on fluorescence and second-order scattering (SOS) has been constructed. Here, MnO₂ nanosheets, both as a fluorescence quencher and signal transducer of SOS, quench the blue fluorescence of CDs by an inner filter effect. Under the excitation of 300 nm, the nanosystem shows a fluorescence emission peak at 405 nm and a SOS peak at 610 nm, respectively. With the increase of AA , the lamellar structure of MnO₂ nanosheets is etched into a smaller nanostructure, causing a decrease of the fluorescence recovery of CDs (405 nm) and decrease of the SOS signal of the MnO₂ nanosheets (610 nm). According to the simultaneous changes of fluorescence and SOS signals, a dual-signal optical sensor toward AA is successfully constructed. Satisfactorily, the optical sensor for AA detection shows a detection limit of 88 and 105 nM for fluorescence and SOS, respectively. The practical application of the designed sensor is verified through the detection of AA content in vitamin C tablets, and satisfactory results are obtained Graphical Abstract A dual-signal sensor of fluorescence (FL) and second-order scattering (SOS) based on the carbon dot (CD) and MnO₂ nanosheet system for ascorbic acid (AA) detection is constructed, in which CDs are used for the FL mode and MnO₂ nanosheets are used for the SOS mode.

Applications of hydrothermal synthesis of Escherichia coli derived carbon dots in in vitro and in vivo imaging and p-nitrophenol detection

Carbon dots (CDs) have broad prospective applications in various fields, and expanding the applications of fluorescent CDs, especially for CDs derived from bacteria, is a major research goal. In this study, novel CDs derived from Escherichia coli BW25113 (WT) were successfully synthesized via a one-step hydrothermal method. Unlike previously developed CDs-E. coli, CDs-WT can be used for microbial imaging of both live and dead cells. We demonstrated the biocompatibility, excellent penetrability, and nontoxic characteristics of CDs-WT for use as fluorescent probes for bioimaging both in vitro and in vivo. Importantly, we provide the first demonstration of CDs-WT distribution in various organs of mice, including the ability to cross the blood-brain barrier and the potential for rapid excretion through the intestines. Additionally, CDs-WT can be instantly utilized as a fluorescent probe for the highly selective and rapid detection of p-nitrophenol (p-NP) by the inner filter effect, with a limit of detection for p-NP of 11 nM, the lowest value reported to date. Hence, our results demonstrate the feasibility of p-NP detection and extend the bio-imaging applications of CDs prepared from bacteria.

A review: recent advances in preparations and applications of heteroatom-doped carbon quantum dots

Carbon quantum dots (CQDs) are widely used in optoelectronic catalysis, biological imaging, and ion probes owing to their low toxicity, stable photoluminescence, and ease of chemical modification. However, the low fluorescence yield and monochromatic fluorescence of CQDs limit their practical applications. This review summarizes the commonly used approaches for improving the fluorescence efficiency of CQDs doped with non-metallic (heteroatom) elements. Herein, three types of heteroatom-doped CQDs have been investigated: (1) CQDs doped with a single heteroatom; (2) CQDs doped with two heteroatoms; and (3) CQDs doped with three heteroatoms. The limitations and future perspectives of doped CQDs from the viewpoint of producing CQDs for specific applications, especially for bioimaging and light emitting diodes, have also been discussed herein.

Biogenesis of Prism-Like Silver Oxide Nanoparticles Using Nappa Cabbage Extract and Their p-Nitrophenol Sensing Activity

The present study aimed to explore the eco-friendly synthesis of prism-like silver oxide nanoparticles (Ag₂ONPs) from nappa cabbage extract and its p-nitrophenol sensing activity. The prepared Ag₂ONPs were characterized by X-ray diffraction (XRD), field-emission scanning spectroscopy (FESEM), energy-dispersive spectroscopy (EDS), transmission electron microscopy (TEM), and ultraviolet (UV)-visible light spectral analysis (UV-Vis). p-Nitrophenol sensing properties of the prepared nanoparticles were also determined using a simple I-V method. The results showed that the as-prepared Ag₂ONPs have a face-centered cubic (fcc) crystalline nature and a prism-like morphology with particle size in the range 21.61-92.26 nm. The result also showed a high intensity of the (111) facet, making the Ag₂ONP-carbon black/nickel foam electrode (Ag₂ONP-C/NFE) exhibit a high-performance response to p-nitrophenol spanning a wide range of concentrations from 1.0 mM to 0.1 pM and a response time of around 5 s, indicating a high potential for water treatment applications.