Chromium removal from contaminated waters using nanomaterials – A review

Luminescent iron phthalocyanine organic polymer nanosheets with space-separated dual-active sites for the detection and photocatalytic reduction of Cr(Ⅵ) from wastewater

Cr(Ⅵ) residues in livestock and poultry wastewater are a rising concern for human health and biotic environments. For the removal of Cr(Ⅵ), its simultaneous reduction and adsorption represents a sustainable and efficient strategy. Herein, iron nodes on covalently bonded two-dimensional phthalocyanine organic polymer (PcOP-Fe) nanosheets with space-separated dual-active sites are developed for the simultaneous detection and removal of Cr(VI) from wastewater. In the FeN4 structure of PcOP-Fe nanosheets, Fe acts as an electron capture center, effectively facilitating the accumulation of photogenerated electrons and transferring them to Cr(VI), thereby achieving its photocatalytic reduction. Meanwhile, pyrrolic nitrogen provides excellent adsorption sites, enabling the adsorption of Cr(III) or Cr(0). Fe accumulates the photogenerated electrons from pyrrole N and transfer them to Cr(Ⅵ). The formation of N-Cr(Ⅲ) bonds causes a space-separation between Cr(Ⅵ) and Cr(III). In addition, PcOP-Fe can be used for a Cr(Ⅵ) detection agent. The photoluminescence intensity decreases linearly with increasing Cr(Ⅵ) concentration from 80 μM to 2 mM, with a limit of detection of 0.18 μM. The PcOP-Fe nanosheets exhibit good Cr(Ⅵ) detection and reduction performance in livestock and poultry wastewater, suggesting their suitability for practical sensing applications. Thus, the PcOP-Fe nanosheets with space-separated dual-active sites are promising for the simultaneous detection and removal of Cr(Ⅵ) in water treatment processes.

Impact of untreated tannery wastewater in the evolution of multidrug-resistant bacteria in Bangladesh

The tannery industry produces one of the worst contaminants, and unsafe disposal in nearby waterbodies and landfills has become an imminent threat to public health, especially when the resulting multidrug-resistant bacteria and heavy metals enter community settings and animal food chains. In this study, we have collected 10 tannery wastewater (TWW) samples and 10 additional non-tannery wastewater (NTW) samples to compare the chemical oxygen demand (COD), pH, biological oxygen demand (BOD), dissolved oxygen (DO), total dissolved solids (TDS), chromium concentration, bacterial load, and antibiotic resistance profiles. While COD, pH, and chromium concentration data were previously published from our lab, this part of the study uncovers that TWW samples had a significantly higher bacterial load, compared to the non-tannery wastewater samples (5.89 × 104 and 9.38 × 103 cfu/mL, respectively), higher BOD and TDS values, and significantly lower DO values. The results showed that 53.4, 46.7, 40.0, and 40.0% of the TWW isolates were resistant to ceftriaxone, erythromycin, nalidixic acid, and azithromycin, respectively. On the other hand, 20.0, 30.0, 50.0, and 40.0% of the NTW isolates were resistant to the same antibiotics, respectively. These findings suggest that the TWW isolates were more resistant to antibiotics than the NTW isolates. Moreover, the TWW isolates exhibited higher multidrug resistance than the NTW isolates, 33.33, and 20.00%, respectively. Furthermore, spearman correlation analysis depicts that there is a negative correlation between BOD and bacterial load up to a certain level (r = - 0.7749, p = 0.0085). In addition, there is also a consistent negative correlation between COD and bacterial load (r = - 0.7112, p = 0.0252) and TDS and bacterial load (r = - 0.7621, p = 0.0104). These findings suggest that TWW could pose a significant risk to public health and the environment and highlight the importance of proper wastewater treatment in tannery industries.

Sustainable Lignin-Reinforced Chitosan Membranes for Efficient Cr(VI) Water Remediation

The pollution of aquatic environments is a growing problem linked to population growth and intense anthropogenic activities. Because of their potential impact on human health and the environment, special attention is paid to contaminants of emerging concern, namely heavy metals. Thus, this work proposes the use of naturally derived materials capable of adsorbing chromium (VI) (Cr(VI)), a contaminant known for its potential toxicity and carcinogenic effects, providing a sustainable alternative for water remediation. For this purpose, membranes based on chitosan (CS) and chitosan/Kraft lignin (CS/KL) with different percentages of lignin (0.01 and 0.05 g) were developed using the solvent casting technique. The introduction of lignin imparts mechanical strength and reduces swelling in pristine chitosan. The CS and CS/0.01 KL membranes performed excellently, removing Cr(VI) at an initial 5 mg/L concentration. After 5 h of contact time, they showed about 100% removal. The adsorption process was analyzed using the pseudo-first-order model, and the interaction between the polymer matrix and the contaminant was attributed to electrostatic interactions. Therefore, CS and CS/KL membranes could be low-cost and efficient adsorbents for heavy metals in wastewater treatment applications.

Synergistic effect of adsorption-photocatalytic reduction of Cr(VI) in wastewater with biochar/TiO2 composite under simulated sunlight illumination

Photocatalysis, which is an alternative technology to conventional methods, utilizes solar energy as the driving force to address environmental concerns and has attracted widespread attention from chemists worldwide. In this study, a series of photocatalytic materials composed of agricultural waste and titanium dioxide (TiO2) nanomaterial was prepared for the synergistic adsorption-photocatalytic reduction of hexavalent chromium in wastewater under mild conditions. The results showed that the TiO2 nanomaterial exhibited a higher photogenerated carrier separation efficiency and performance for the adsorption-photocatalytic reduction of Cr(VI) after loading straw biochar (BC). When the loading amount of BC was 0.025 g (i.e., TBC-3), the removal efficiency of Cr(VI) was as high as 99.9% under sunlight irradiation for 25 min, which was 2.9 and 3.5 times higher than that of pure TiO2 and BC samples, respectively. Additionally, after four cycles of experiments, the removal efficiency of Cr(VI) by TBC-3 remained at about 93.0%, proving its good chemical ability in our reaction system. Its excellent adsorption-photocatalytic performance is mainly attributed to the synergistic effect of the strong adsorption of BC and the outstanding photocatalytic performance of TiO2. Finally, the possible mechanism for the synergistic adsorption-photocatalytic reduction on BC/TiO2 to remove the highly toxic Cr(VI) in wastewater was proposed.

Fe-doping green fluorescent carbon dots via co-electrolysis of chrysoidine G and potassium ferrocyanide for sensitive Cr(VI) detection

In this study, we aimed to synthesis of Fe-doping green fluorescent carbon dots (G-CDs) through the co-electrolysis of chrysoidine G and potassium ferrocyanide for Cr(VI) detection. The use of potassium ferrocyanide improves the quantum yield and sensing performance of G-CDs toward Cr(VI). The G-CDs have a maximum excitation wavelength of 308 nm and an emission wavelength of 510 nm. Comprehensive analyses including Raman, FT-IR, and XPS provided insights into the chemical structure and composition of the G-CDs. Under optimal conditions, G-CDs demonstrated concentration-dependent quenching upon interaction with Cr(VI). A linear relationship within the range of 0.25-100 µM was established with a calibration equation of ΔF/F0 = 0.005 + 0.015CCr(VI), yielding an R2 value of 0.996 and a limit of detection of 0.15 μM. The applicability of the G-CDs method was demonstrated by successful Cr(VI) detection in water samples with recovery rates ranging from 98.8 % to 100.1 % and relative standard deviation within 3.0 %. The fluorescence lifetime and Zeta potential measurements confirmed that the mechanism was via a static quenching process, while redox reaction, nanoparticle aggregation, and surface charge variation also played significant roles.

Removal of chromium(III) from contaminated waters using cobalt ferrite: how safe is remediated water to aquatic wildlife?

The release of hazardous elements by industrial effluents to aquatic ecosystems is a potential threat to the environment. Chromium (Cr) is one of the elements whose levels in several freshwater ecosystems should be reduced to promote water reuse. In recent years, magnetic materials have gained increasing interest as sorbents because of their easy removal from treated water through magnetic separation. In this study, colloidal cobalt ferrite (CoFe2O4) particles were investigated as magnetic sorbents for chromium-aqueous chemical species. The oxidative stress responses of Mytilus galloprovincialis mussels exposed to 200 μg/L of Cr, resembling remediated water, were evaluated. More than 95% of Cr was removed from contaminated solutions by CoFe2O4 aqueous suspensions at pH 6 and pH 10. The kinetics of sorption experiments were examined using pseudo-1st order, pseudo-2nd order and Elovich models to evaluate which mathematical model has a better adjustment to the experimental data. The present study revealed that the levels of Cr that remained in remediated water induced limited biochemical changes in mussels, being considered safe for aquatic systems. Overall, the use of cobalt ferrite-based sorbents may constitute a promising approach to remediate contaminated water.

Evaluating the effectiveness of coagulation-flocculation treatment on a wastewater from the moroccan leather tanning industry : An ecological approach

The removal of pollutants from tannery wastewaters, which is renowned for its substantial volumes, intricate composition, and considerable hazards to human health and the environment, is a prominent research area in the field of water treatment. The aim of this study is to employ a bio-coagulant derived from Parkinsonia aculeata seeds and a bio-flocculant derived from Hibiscus esculentus to minimise the concentration of pollutants in the combined wastewater originating from tanneries. In the course of the research, a thorough physicochemical analysis of the coagulating and flocculating agents, Parkinsonia aculeata (PA) and Hibiscus esculentus (HE), was performed using techniques such as XRD (X-ray diffraction), FTIR (Fourier-transform infrared spectroscopy), and SEM-EDS (scanning electron microscopy-energy dispersive X-ray spectroscopy). This analysis aimed to determine the composition and characteristics of these biomasses. Subsequently, a comprehensive overview was conducted to summarize the various factors that influence the treatment of tannery wastewater through coagulation/flocculation. This was accomplished by manipulating the target factors and observing their impact on the removal of specific physicochemical parameters such as chemical oxygen demand (COD), electrical conductivity (EC), total chromium (Cr) and Optical density (OD). The variables that were established include pH, dosage of coagulant and flocculant, as well as the speed and duration of agitation in both the fast and slow mixing stages. The experiments were carried out while taking into account the optimal parameters, leading to the near-complete removal of all analyzed pollutants. The optimal requirements for the Parkinsonia aculeata-Hibiscus esculentus Coagulation Flocculation System involve adjusting the pH to 8, choosing concentrations of approximately 1.25 g L-1 and 0.6 g L-1 for the coagulant and flocculant respectively, maintaining a fast speed of 170 rpm for 3 min while keeping the slow agitation at around 30 rpm for 20 min. The removal rates achieved after treating tannery wastewater using the PA-HE coagulant-flocculant combination demonstrate high efficacy, with values reaching approximately 100% for TSS, 98.71% for BOD5, 99.93% for COD, 98.88% for NH4+, 98.21% for NO3-, 90.32% for NO2-, 93.13% for SO42-, 95.44% for PO43-, 96.08% for OD and 60% for total chromium. These results indicate the successful removal of a wide range of pollutants from tannery wastewater through the PA-HE treatment method. In predicting the CF treatment approach, PCA has been employed to preprocess the input data and determine the key variables that impact the process. This can streamline the modeling process and enhance the precision of the predictions.

An in-depth insight into the simultaneous oxidation of sulfamethoxazole and reduction of Cr (VI) by one system of water film DBD plasma: The interaction effect, role of active species, and their dominant to pathways

This study aims to deeply investigate the simultaneous elimination of sulfamethoxazole (SMZ) and Cr (VI) through one system of water film dielectric barrier discharge (WFDBD) plasma. The interaction effect of SMZ degradation and Cr (VI) reduction and dominant effect of active species were highlighted. Results showed that the oxidation of SMZ and the reduction of Cr (VI) directly promote each other. When the concentration of Cr (VI) raised from 0 to 2 mg L^-1, the degradation rate of SMZ enhanced from 75.6% to 88.6%, respectively. Similarly, when the concentration of SMZ improved from 0 to 15 mg L^-1, the removal efficiency of Cr (VI) improved from 70.8% to 84.3%, respectively. ·OH, ¹O₂ and ·O₂^- play crical roles for SMZ degradation, and e^-, ·O₂^-, ·H and H₂O₂ dominated to the Cr (VI) reduction. The variations of pH, conductivity and TOC during the removal process were also explored. The removal process was studied by UV-vis spectroscopy and a three-dimensional excitation-emission matrix. Based on DFT calculation and LC-MS analysis, free radicals dominated SMZ degradation pathways in the WFDBD plasma system were clarified. Besides, the influence of Cr (VI) on SMZ degradation pathway was clarified. The ecotoxicity of SMZ and the toxicity of Cr (VI) into Cr (III) were greatly reduced. This study provides a significant reference value for the application and mechanism of plasma simultaneous removal of organic pollutants and heavy metals in wastewater.

A review of novel green adsorbents as a sustainable alternative for the remediation of chromium (VI) from water environments

The presence of heavy metal, chromium (VI), in water environments leads to various diseases in humans, such as cancer, lung tumors, and allergies. This review comparatively examines the use of several adsorbents, such as biosorbents, activated carbon, nanocomposites, and polyaniline (PANI), in terms of the operational parameters (initial chromium (VI) concentration (C_o), temperature (T), pH, contact time (t), and adsorbent dosage) to achieve the Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption. The study finds that the use of biosorbents (fruit bio-composite, fungus, leave, and oak bark char), activated carbons (HCl-treated dry fruit waste, polyethyleneimine (PEI) and potassium hydroxide (KOH) PEI-KOH alkali-treated rice waste-derived biochar, and KOH/hydrochloric acid (HCl) acid/base-treated commercial), iron-based nanocomposites, magnetic manganese-multiwalled carbon nanotubes nanocomposites, copper-based nanocomposites, graphene oxide functionalized amino acid, and PANI functionalized transition metal are effective in achieving high Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption, and that operational parameters such as initial concentration, temperature, pH, contact time, and adsorbent dosage significantly affect the Langmuir's maximum adsorption capacity (q_m). Magnetic graphene oxide functionalized amino acid showed the highest experimental and pseudo-second-order kinetic model equilibrium adsorption capacities. The iron oxide functionalized calcium carbonate (IO@CaCO₃) nanocomposites showed the highest heterogeneous adsorption capacity. Additionally, Syzygium cumini bark biosorbent is highly effective in treating tannery industrial wastewater with high levels of chromium (VI).

Staphylococcus edaphicus KCB02A11 incorporated with natural adsorbents: first report on its tolerance and removal of hexavalent chromium [Cr(VI)]

Deteriorating the quality of different parts of the ecosystem due to toxic metals is a serious global issue. Hexavalent chromium is a metal that can cause adverse effects on all living beings, including plants, animals, and microorganisms, on exposure to high concentrations for prolonged periods. Removing hexavalent chromium from various types of wastes is challenging; hence the present study investigated the use of bacteria incorporated with selected natural substrates in removing hexavalent chromium from water. Isolated Staphylococcus edaphicus KCB02A11 has shown higher removal efficiency with a wide hexavalent chromium range (0.025-8.5 mg/L) within 96 h. Incorporating the isolated strain with natural substrates commonly found in the environment (hay and wood husk) showed high removal potential [100% removal with 8.5 mg/L of Cr(VI)], even within less than 72 h, with the formation of biofilms on the used substrates applied for metal removal on a large scale for prolonged periods. This study is the first report investigating hexavalent chromium tolerance and removal by Staphylococcus edaphicus KCB02A11.

Chromium (III) and chromium (VI) removal and organic matter interaction with nanofiltration

Chromium (Cr) is a toxic inorganic contaminant for drinking water, in which the concentration has to be controlled for human health and safety. Cr retention was investigated with stirred cell experiments using sulphonated polyethersulfone nanofiltration (NF) membranes of different molecular weight cut-off (MWCO). Cr(III) and Cr(VI) retention follow the order of the MWCO of the studied NF membranes; HY70-720 Da > HY50-1000 Da > HY10-3000 Da with a pH dependency, especially for Cr(III). The importance of the charge exclusion was highlighted when Cr(OH)₄^- (for Cr(III)) and CrO₄^2- (for Cr(VI)) was the predominant species in the feed solution. In presence of organic matter, namely humic acid (HA), Cr(III) retention increased by 60 %, while no influence of HA was observed for Cr(VI). HA did not induce major modifications on the membrane surface charge for these membranes. Solute-solute interaction, in particular Cr(III)-HA complexation, was the responsible mechanism for the increase in Cr(III) retention. This was confirmed by asymmetric flow field-flow fractionation, coupled with inductively coupled plasma mass spectrometry (FFFF-ICP-MS) analysis. Cr(III)-HA complexation was significant at HA concentrations as low as 1 mgC/L. The chosen NF membranes were able to achieve the EU guideline (25 μg/L) for Cr in drinking water for a feed concentration of 250 μg/L.

Status of Ecosystem Services in Abandoned Mining Areas in the Iberian Peninsula: Management Proposal

An abandoned sphalerite mining area in the southwest (SW) of the Iberian Peninsula was studied to evaluate the impact that the presence of metal(loid)s has on soil and ecosystem health. Five zones were delimited: sludge, dump, scrubland, riparian zone, and dehesa. Critical total levels of lead (Pb), zinc (Zn), thallium (Tl), and chromium (Cr), well above the limit indicative of toxicity problems, were found in the areas close to the sources of contamination. Pb-Zn concentrations were very high in the riparian zone, reaching values of 5875 mg/kg Pb and 4570 mg/kg Zn. The whole area is classifiable as extremely contaminated with Tl, with concentrations above 370 mg/kg in the scrubland. Cr accumulation mainly occurred in areas away from the dump, with levels up to 240 mg/kg in the dehesa. In the study area, several plants were found growing luxuriantly despite the contamination. The measured metal(loid)s content is the cause of a significant decrease in ecosystem services, resulting in unsafe soils for food and water production, so the implementation of a decontamination program is advisable. The plant species Retama sphaerocarpa, present in the sludge, scrubland, riparian zone, and dehesa, is postulated as suitable for use in phytoremediation.

High Adsorption of Hazardous Cr(VI) from Water Using a Biofilter Composed of Native Pseudomonas koreensis on Alginate Beads

Most conventional methods to remove heavy metals from water are efficient for high concentrations, but they are expensive, produce secondary pollution, and cannot remove low concentrations. This paper proposes a biological system to remove Cr(VI) from aqueous solutions; the biofilter is composed of a native Pseudomonas koreensis immobilized in calcium alginate beads. Lab experiments were conducted in batch reactors, considering different operating conditions: Cr(VI) concentration, temperature, pH, and time. At 30 °C and a pH of 6.6, the immobilized bacteria achieved their optimal adsorption capacity. In the chromium adsorption system, saturation was reached at 30 h with a qmax = 625 mg g-1. By adjusting the experimental data to the Langmuir and Freundlich models, it is suggested that P. koreensis forms a biofilm with a homogeneous surface where Cr(VI) is adsorbed and that the bacteria also incorporates the metal in its metabolism, leading to a multilayer adsorption. On the other hand, using Fourier transform infrared spectroscopy, it was inferred that the functional groups involved in the adsorption process were O-H and C=O, which are a part of the P. koreensis cell wall.

Reduction of hexavalent chromium using bacterial isolates and a microbial community enriched from tannery effluent

We investigated microbial growth in increasing concentrations of hexavalent chromium (Cr(VI)) and its reduction by a microbial community enriched from tannery effluent and by the bacterial strains isolated from the enriched community. The bacterial growth was monitored by measuring the optical cell density (OD₆₅₀), while the Cr(VI) concentration in the samples was determined using spectrophotometry and liquid chromatography hyphenated to inductively coupled plasma mass spectrometry (HPLC-ICP-MS). At a Cr(VI) concentration of 100 mg/L, the isolates affiliated with Pseudomonas aeruginosa (P. aeruginosa) reached higher optical cell densities, but were in general less effective for Cr(VI) reduction than the isolates affiliated with Mammaliicoccus sciuri (M. sciuri). All three M. sciuri isolates and only one of the seven P. aeruginosa isolates were able to reduce 50% of the Cr(VI) with an initial concentration of 100 mg/L within 24 h (pH 7.1), while the six isolates affiliated with P. aeruginosa were less effective. Compared to the isolated, individual bacterial strains, the enriched microbial community was better adapted to the elevated Cr(VI) concentrations, but needed a longer time (48 h) to reduce the Cr(VI) with the same efficacy as the most efficient individual isolates. The ability of the enriched microbial community and the isolated bacterial strains to reduce the Cr(VI) highlights their potential for use in the rapid bioremediation of wastewaters contaminated with Cr(VI).

Cr(III) Ion-Imprinted Hydrogel Membrane for Chromium Speciation Analysis in Water Samples

Novel Cr(III)-imprinted poly(vinyl alcohol)/sodium alginate/AuNPs hydrogel membranes (Cr(III)-IIMs) were obtained and characterized and further applied as a sorbent for chromium speciation in waters. Cr(III)-IIMs were prepared via solution blending method using blends of poly(vinyl alcohol) and sodium alginate as film-forming materials, poly(ethylene glycol) as a porogen agent, sodium alginate stabilized gold nanoparticles (SA-AuNPs) as a crosslinking and mechanically stabilizing component, and Cr(III) ions as a template species. The physicochemical characteristics of pre-synthesized AuNPs and obtained hydrogel membranes Cr(III)-IIM were studied by UV-vis and FTIR spectroscopy, TEM and SEM observations, N₂ adsorption-desorption measurements, and XRD analysis. The mechanism of the adsorption process toward Cr(III) was best described by pseudo-first-order kinetic and Langmuir models. Experiments performed showed that quantitative retention of Cr(III) is attained in 20 h at pH 6 and temperature 40 °C. Under the same conditions, the adsorption of Cr(VI) is below 5%. A simple and sensitive analytical procedure was developed for the speciation of Cr in an aquatic environment using dispersive solid phase extraction of Cr(III) by Cr(III)-IIM prior to selective Cr(VI) measurement by ETAAS in the supernatants. The detection limits and reproducibility achieved for the Cr speciation analysis fulfill the requirements for their monitoring in waters under the demand of the Water Framework Directive.

Recent developments in MOF and MOF based composite as potential adsorbents for removal of aqueous environmental contaminants

With the growth of globalization which has been the primary cause of water pollution, it is utmost necessary for us living being to have access to clean water for the purpose of drinking, washing and various other useful applications. With the purpose of future security and to restore our ecological balance, it is essential to give much significance towards the removal of unwanted toxic contaminants from our water resources. In this regard adsorptive removal of toxic pollutants from wastewater with porous adsorbent is regarded as one of the most promising way for water decontamination process. Metal organic frameworks (MOFs) comprising of uniformly arranged pores, abundant active sites and containing an easily tunable structure has aroused as a promising material for adsorbent to remove the unwanted contaminants from water sources. The adsorption of pollutants by the different MOFs surface are driven by various interactions including π-π, acid-base, electrostatic and H-bonding etc. On the other hand, the removal of various contaminants by MOFs is influenced by various factors including pH, temperature and initial concentration. In this review we will specifically discuss the adsorptive removal of different organic and inorganic pollutants present in our water systems with the use of MOFs as adsorbent along with the various factors and interaction mechanism manipulating the adsorption behaviour.

Water security threats and challenges following the rupture of large tailings dams

The rupture of mine-tailings dams can severely contaminate rivers, because released tailings can interact with water for years keeping contaminant concentrations high. The general purpose of this study was to examine the rupture of B1 tailings dam in Ferro-Carvão stream (municipality of Brumadinho, state of Minas Gerais, Brazil), which occurred in 25 January 2019 and contaminated the main water course (Paraopeba River) with 2.8 Mm³ of metal-rich tailings. The specific purpose was to assess the percentage of non-conforming concentrations following the event, considering the Normative Deliberation COPAM/CERH-MG no. 1. The results showed non-conforming aluminum, iron, manganese, lead, phosphorus and turbidity concentrations, clearly above pre-rupture averages, especially in the rainy period. The catastrophe triggered the suspension of Paraopeba River as drinking water source to the Metropolitan Region of Belo Horizonte (BHMR; 6 million people). Since then, the supply to the BHMR became an everyday challenge to water management authorities, because the Paraopeba source represented a 30% share. Mitigation measures are therefore urgently needed. As complementary objective to this study, we aimed to verify the possibility to restore drinking water supply through conventional treatment. The treatability of Paraopeba River water was assessed by the Raw Water Quality Index considering the rainy and dry periods in separate. The results suggested the possibility to lift up the suspension in the dry period, improving the regional water security. Considering the huge dataset on which this study is standing, our results are generalizable to similar events with sparser information.

Comparison of Cr(VI) adsorption and photocatalytic reduction efficiency using leonardite powder

It is very important to treat Cr(VI) from the aquatic environment due to its toxic and harmful effects. Conventional treatment methodology involving biological pathways is generally ineffective for wastewater containing Cr(VI). Therefore, it is necessary to develop environmentally friendly and economical methods to remove Cr(VI) from the aquatic environment. In this study, leonardite, which is a natural mineral that has no harmful effects on the environment, was used for Cr(VI) removal. Leonardite was used in both adsorption and photocatalytic treatment systems by only pulverizing without any chemical treatment. Characterizations of leonardite were obtained using X-ray fluorescence (XRF), fouirer transform infrared spektrofotometre (FTIR), scanning electron microscopy (SEM) with energy dispersive X-ray analysis (EDX) analyses methods. The effects of solution pH (2-10), particle size (45-300 μm), adsorbent dose (0.25-3 g/L), and initial concentration (10-30 mg/L) on Cr(VI) removal efficiency were investigated in both adsorption and photocatalytic experiments. In the adsorption process, a complete removal efficiency (100%) was obtained for 3 g/L of adsorbent dose with an initial Cr(VI) concentration of 10 mg/L at pH 2 for 2 h. In the photocatalytic process, 100% removal efficiency of Cr(VI) was obtained when four times less adsorbent dosage was used under the same conditions. In addition, the reuse of leonardite powder was also investigated under optimum experimental conditions. Leonardite powder preserved approximately 70% of its activity in the photocatalytic process while it lost 50% of its activity after 5 reuses in adsorption process.

Method and mechanism of chromium removal from soil: a systematic review

Heavy metal pollution has increasingly affected human life, and the treatment of heavy metal pollution, especially chromium pollution, is still a major problem in the field of environmental governance. As a commonly used industrial metal, chromium can easily enter the environment with improperly treated industrial waste or wastewater, then pollute soil and water sources, and eventually accumulate in the human body through the food chain. Many countries and regions in the world are threatened by soil chromium pollution, resulting in the occurrence of cancer and a variety of metabolic diseases. However, as a serious threat to agriculture, food, and human health. Notwithstanding, there are limited latest and systematic review on the removal methods, mechanisms, and effects of soil chromium pollution in recent years. Hence, this article outlines some of the methods and mechanisms for the removal of chromium in soil, including physical, chemical, biological, and biochar methods, which provide a reference for the treatment and research on soil chromium pollution drawn from existing publications.

Data-Driven Machine Learning Intelligent Tools for Predicting Chromium Removal in an Adsorption System

This study investigates chromium removal onto modified maghemite nanoparticles in batch experiments based on a central composite design. The effect of modified maghemite nanoparticles on the adsorptive removal of chromium was quantitatively elucidated by fitting the experimental data using artificial neural network (ANN) and adaptive neuro-fuzzy interference system (ANFIS) modeling approaches. The ANN and ANFIS models, relating the inputs, i.e., pH, adsorbent dose, and initial chromium concentration to the output, i.e., chromium removal efficiency (RE), were developed by comparing the predicted value with that of the experimental values. The RE of chromium ranged from 49.58% to 92.72% under the influence of varying pH (i.e., 2.6–9.4) and adsorbent dose, i.e., 0.8 g/L to 9.2 g/L. The developed ANN model fits the experimental data exceptionally well with correlation coefficients of 1.000 and 0.997 for training and testing, respectively. In addition, the Pearson’s Chi-square measure (χ2) of 0.0004 and 0.0673 for the ANN and ANFIS models, respectively, indicated the superiority of ANN over ANFIS. However, a small discrepancy in the predictability of the ANFIS model was observed owing to the fuzzy rule-based complexity and overtraining of data. Thus, the developed models can be used for the online prediction of RE onto synthesized maghemite nanoparticles with different sets of input parameters and it can also predict the operational errors in the system.

Carnation-like Morphology of BiVO4-7 Enables Sensitive Photoelectrochemical Determination of Cr(VI) in the Food and Environment

Hexavalent chromium, namely, Cr(VI), is a significant threat to ecological and food safety. Current detection methods are not sensitive to Cr(VI). A photoelectrochemical (PEC) sensor based on bismuth vanadate (BiVO4) was developed for sensitive detection of Cr(VI). First, BiVO4-X (X: the pH of the reaction precursor solution) was synthesized using a facile surfactant-free hydrothermal method. The BiVO4-X morphology was well controlled according to pH values, showing rock-like (X = 1), wrinkled bark-like (X = 4), carnation-like (X = 7), and the collapsed sheet-like morphologies (X = 9, 12). BiVO4-7 exhibited excellent photoelectric performance due to a proper band structure under visible light and a large specific surface area. Then, BiVO4-7 was used to construct a PEC sensor to detect Cr(VI), which was demonstrated to have a low detection limit (10 nM) and wide detection range (2-210 μM). The BiVO4-7 PEC sensor had a stable output signal, as well as excellent reproducibility, repeatability, and selectivity. We used the BiVO4-7 PEC sensor to detect Cr(VI) in real environmental and food samples, resulting in a satisfactory recovery of 90.3-103.0%, as determined by comparison with results obtained using a spectrophotometric method. The BiVO4-7 PEC sensor is promising for practical application to heavy metal detection in the food and environment.

Mechanistic insights of hexavalent chromium remediation by halloysite-supported copper nanoclusters

Chromium (Cr) pollution is a significant environmental concern with remediation challenge. Hexavalent chromium (Cr(VI)) is more toxic than trivalent chromium (Cr(III)) due to its mutagenicity and oncogenicity. In this investigation, a multi-functional material, copper nanoclusters (CuNCs)-halloysite nanotubes (HNT) composite (CuNCs@HNT), has been synthesised in an eco-friendly manner and utilised for Cr(VI) remediation. Advanced analytical tools confirmed the seeding of ultra-fine CuNCs onto HNT surfaces. The maximum adsorption capacity of CuNCs@HNT is 79.14 ± 6.99 mg/g at pH 5 ± 0.1 with an increment at lower pHs. This performance was comparable for real surface stream water as well as other reported materials. The pseudo-second-order kinetic-, intra-particle diffusion- and Freundlich isotherm models well fit the experimental data implying that the chemisorption, multiphase diffusion and multi-molecular layer distribution occurred during adsorption. The Fourier-transform infrared and the x-ray photoelectron spectra also ensured the transformation of Cr(VI) to Cr(III) indicating the material's suitability for concurrent adsorption and reduction of Cr(VI). While coexisting cations and anions did not overwhelm this adsorption, CuNCs@HNT was regenerated and reused five successive times in adsorption-desorption cycles without significant loss of adsorption capacity and material's integrity. Therefore, this multi-functional, biocompatible, low-cost and stable CuNCs@HNT composite may have practical application for similar toxic metals remediation.

Two dimensional MXenes as emerging paradigm for adsorptive removal of toxic metallic pollutants from wastewater

Effective methods for removing harmful metals from wastewater have had a huge impact on reducing freshwater scarcity. Because of its excellent removal effectiveness, simplicity and low cost at ambient conditions, adsorption is one of the most promising purifying approaches. MXene-based nanoarchitectures have proven to be effective adsorbents in a variety of harmful metal removal applications. This owes from the distinctive features such as, hydrophilicity, high surface area, electron-richness, great adsorption capacity, and activated metallic hydroxide sites of MXenes. Given the rapid advancement in the design and synthesis of MXene nanoarchitectures for water treatment, prompt updates on this research area are needed that focus on removal of toxic metal, such as production routes and characterization techniques for the advantages, merits and limitations of MXenes for toxic metal adsorption. This is in addition to the fundamentals and the adsorption mechanism tailored by the shape and composition of MXene based on some representative paradigms. Finally, the limits of MXenes are highlighted, as well as their potential future research directions for wastewater treatment. This manuscript may initiate researchers to improve unique MXene-based nanostructures with distinct compositions, shapes, and physiochemical merits for effective removal of toxic metals from wastewater.

Fabrication and characterization of electrospun zein/nylon-6 (ZN6) nanofiber membrane for hexavalent chromium removal

Zein has drawn attention for its great potential for biodegradability and adsorption of hexavalent chromium Cr(VI) that is a carcinogenic industrial pollutant. Zein is a biopolymer extracted from corn and is used for many purposes, but because of its poor stability in aqueous solution, a novel composite of zein and nylon-6 was used to synthesize a nanofibrous membrane using electrospinning to improve its stability and tensile strength. The scanning electron microscope (SEM) image of the zein/nylon-6 (ZN6) nanofiber membrane showed a smooth, beadless, and continuous structure of the nanofibers, but the Fourier transform infrared (FTIR) spectrum of pristine and Cr(VI) saturated ZN6 showed that peaks of secondary amide, carbonyl, and hydroxyl functional groups were involved in adsorption. Optimized experimental parameters were obtained with pH 2.0, contact time 60 min, adsorbent dosage 25 mg, and adsorbate concentration 5.0 mg Cr-VI/mL. Experimental results show that the ZN6 nanofibers removed 87% Cr(VI) with an adsorption capacity of 4.73 mg/g at ambient temperature. Also, the Langmuir isotherm fits well, and the adsorption process followed a pseudo-2^nd-order kinetics with r² of 0.90 and 0.99 respectively.

Removal of chromate ions from leachate-contaminated groundwater samples of Khan Chandpur, India, using chitin modified iron-enriched hydroxyapatite nanocomposite

Chromite ore processing residues (COPR) are real environmental threats, leading to CrO42-, i.e., Cr (VI) leaching into groundwater. It is of serious concern as Cr (VI) is proven to be carcinogenic. Here we emphasize the application of novel and eco-friendly chitin functionalized iron-enriched hydroxyapatite nanocomposite (HAP-Fe0-Ct) in the remediation of Cr (VI)-contaminated groundwater samples collected from Khan Chandpur, India, where the level of Cr (VI) is found to be 11.7 mg/L in a complex aqueous matrix having 793 mg/L of total dissolved solids. Chitin functionality in the composite has resulted in positive zeta potential at circum-neutral pH, favoring electrostatic attraction of chromate ions and resulting in its bulk surface transport. The HAP-Fe0-Ct showed faster kinetics of removal with efficiency (qm = 13.9 ± 0.46 mg/g) for Cr (VI). The composite has shown sorption equilibrium and 100% removal of Cr (VI) within 3 h of interaction time in groundwater samples. No Cr (VI) leaching in the acid wash process at pH 3.5 also suggests chromium's strong chemisorption onto nanocomposite. During the interaction in aqueous solutions, the reduced iron (Fe0) on the nanocomposite becomes oxidized, suggesting the probable simultaneous reduction of Cr (VI) and its co-precipitation. Continuous column extraction of chromate ions was also efficient in both spiked solutions (39.7 ± 0.04 mg/g) and COPR contaminated water (13.2 ± 0.09 mg/g). Reusability up to three cycles with almost complete Cr (VI) removal may be attributed to surface protonation, new binding sites generation, and electron transfer from Fe0 core through defects. The study concludes that HAP-Fe0-Ct could be utilized for continuous Cr (VI) removal from COPR contaminated complex groundwater matrices.

A highly porous animal bone-derived char with a superiority of promoting nZVI for Cr(VI) sequestration in agricultural soils

Paddy soil and irrigation water are commonly contaminated with hexavalent chromium [Cr(VI)] near urban industrial areas, thereby threatening the safety of agricultural products and human health. In this study, we develop a porous and high specific area bone char (BC) to support nanoscale zero-valent iron (nZVI) and apply it to remediate Cr(VI) pollution in water and paddy soil under anaerobic conditions. The batch experiments reveal that BC/nZVI exhibits a higher removal capacity of 516.7 mg/(g•nZVI) for Cr(VI) than nZVI when normalized to the actual nZVI content, which is 2.8 times that of nZVI; moreover, the highest nZVI utilization is the nZVI loading of 15% (BC/nZVI15). The Cr(VI) removal efficiency of BC/nZVI15 decreases with increasing pH (4 - 10). Coexisting ions (phosphate and carbonate) and humic acid can inhibit the removal of Cr(VI) with BC/nZVI15. Additionally, BC exhibits a strong advantage in promoting Cr(VI) removal by nZVI compared to the widely used biochar and activated carbon. Our results demonstrate that reduction and coprecipitation are the dominant Cr(VI) removal mechanisms. Furthermore, BC/nZVI15 shows a significantly higher reduction and removal efficiency as well as a strong anti-interference ability for Cr(VI) in paddy soil, as compared to nZVI. These findings provide a new effective material for remediating Cr(VI) pollution from water and soil.

Preparation of Sn/Fe nanoparticles for Cr (III) detection in presence of leucine, photocatalytic and antibacterial activities

In this project, Sn-Fe bimetallic nanoparticles were prepared by a facile method. The bimetallic nanoparticles of it could be well established by a field emission scanning electron microscope micrographs. Due to the excellent synergistic influence between Sn-Fe nanoparticles and leucine indicated a great performance for determination of Cr³⁺. The material was characterized using the XRD, DLS, and zetasizer for theevaluation of crystal structure and morphologyinformation.The potential and effective size of Sn-Fe NPs was -29.10 mV and 30 nm, respectively. Cr³⁺ ions interaction with the Sn-Fe NPs-leucine probe was carried out in 1 min as response time. The limit of detection of Sn-Fe NPs for Cr(III) colorimetric method was 0.25 nM. The prepared nanoparticles showed impressive photocatalysis efficiency for degradation of MO was about 95.1% in 35 min, thus the prepared nanoparticles may be developed for the detoxification of pollution. The prepared nanoparticles depicted effective antibacterial activity againstC. botulinum and, H. pylori bacteria.

Biodegradable gelatin composite hydrogels filled with cellulose for chromium (VI) adsorption from contaminated water

Biopolymers are promising materials for water treatment applications due to their abundance, low cost, expandability, and chemical structure. In this work, gelatin hydrogels filled with cellulose in the form of pristine eucalyptus residues (PER) or treated eucalyptus residues (TER) were prepared for adsorption and chromium removal in contaminated water. PER is a lignocellulosic compound, with cellulose, hemicellulose, and lignin, while TER has cellulose as a major component. FT-Raman Spectroscopy and FTIR analysis confirmed the crosslink reaction with glutaraldehyde and indicated that fillers altered the gelatin molecular vibrations and formed new hydrogen bonds, impacting the hydrogels' crystalline structure. The hydrogen bond energy was altered by the cellulosic fillers' addition and resulted in higher thermal stability (~10 °C). Hydrogels presented a Fickian diffusion, where gelatin hydrogel showed the highest swelling ability (466%), and composites showed lower values with the filler content increase. The chromium adsorption capacity presented values between 12 and 13 mg/g, i.e., featuring an excellent removal capacity which is related with hydrogel crosslinked structure and fibers surface hydroxyl groups, highlighting gelatin hydrogel TER 5% with better removal capacity. The developed hydrogels were produced from biomacromolecules with low-cost and potential application in contaminated water.

Green Synthesis of Iron Nanoparticles Using Green Tea and Its Removal of Hexavalent Chromium

Chromium (VI) is a ubiquitous groundwater contaminant and it is dangerous to both ecological and human health. Iron nanoparticles (nFe) have a large specific surface area and they are highly efficient in removing chromium (VI) from aqueous solution. However, since the traditional reductive synthesis of nFe is relatively expensive and often causes secondary pollution, it is necessary to develop a low-cost green synthetic method using plant extracts. Synthetic conditions are important for obtaining highly active chromium-removing nanomaterials. In this paper, a green tea extract was used to prepare nFe and the effects of synthetic conditions on subsequent remediation performance were investigated. The optimal conditions included a green tea extract/Fe²⁺ ratio of 1:2 (91.6%), a green tea extract temperature of 353 K (88.3%) and a synthetic temperature of 298 K (88.1%). Advanced material characterization techniques, including XPS, SEM-EDS, TEM, and Brunauer–Emmett–Teller (BET) confirmed that the average particle size was between 50–80 nm, with a specific surface area of 42.25 m²·g⁻¹. Furthermore nFe had a core-shell structure, where Fe (0) constituted the core and a shell was composed of iron oxide. Finally, a mechanism for synthesizing nFe by green tea extract was proposed, providing a theoretical basis for optimized synthetic conditions for preparing nFe when using green tea extract.

Simultaneous Adsorption and Reduction of Cr(VI) to Cr(III) in Aqueous Solution Using Nitrogen-Rich Aminal Linked Porous Organic Polymers

Two novel nitrogen-rich aminal linked porous organic polymers, NRAPOP-O and NRAPOP-S, have been prepared using a single step-one pot Schiff-base condensation reaction of 9,10-bis-(4,6-diamino-S-triazin-2-yl)benzene and 2-furaldehyde or 2-thiophenecarboxaldehyde, respectively. The two polymers show excellent thermal and physiochemical stabilities and possess high porosity with Brunauer–Emmett–Teller (BET) surface areas of 692 and 803 m2 g−1 for NRAPOP-O and NRAPOP-S, respectively. Because of such porosity, attractive chemical and physical properties, and the availability of redox-active sites and physical environment, the NRAPOPs were able to effectively remove Cr(VI) from solution, reduce it to Cr(III), and simultaneously release it into the solution. The efficiency of the adsorption process was assessed under various influencing factors such as pH, contact time, polymer dosage, and initial concentration of Cr(VI). At the optimum conditions, 100% removal of Cr(VI) was achieved, with simultaneous reduction and release of Cr(III) by NRAPOP-O with 80% efficiency. Moreover, the polymers can be easily regenerated by the addition of reducing agents such as hydrazine without significant loss in the detoxication of Cr(VI).

Multi-objective optimization of permeable reactive barrier design for Cr(VI) removal from groundwater

The present study aims to develop a practical approach for the optimal permeable reactive barrier (PRB) design towards Cr(VI) removal from groundwater. Batch and column experiments were performed to investigate the characteristics of the four proposed reactive materials; nanoscale zero-valent iron (Fe⁰), bimetallic nanoscale zero-valent iron (Fe⁰/Cu), activated carbon (AC) and sand/zeolite mixture (S/Z). Kinetic analysis and dynamic modeling of the experimental data were implemented to determine the controlling conditions of the reactive performance of the PRB's materials. The sensitivity index of the design parameters was examined as an indicator of their effect on the reactive responses. Moreover, the Response Surface Methodology (RSM) was considered for optimizing the design variables of the PRB based on the practical factorial analysis. Results revealed that Fe⁰ and Fe⁰/Cu showed high performance in Cr(VI) removal, with a slight superiority to Fe⁰, with final removal efficiency values of 89.7 and 84.1%, respectively. Kinetic analysis depicted that pseudo second order was the best fitting model for Cr(VI) removal in the four materials' cases. ANOVA statistical analysis revealed that quadratic polynomial model was the best model, corresponding to the highest correlation efficiency and adequate precision, to describe the relationships in the four PRB's cases between the selected dependent variables; resident time (t_R), reactive material mass per sectional area of contaminant plume (M/A) and reactive material cost (Cost_PRB) towards the independent parameters; barrier thickness (b) and permeability (K_r). Additionally, sensitivity analysis has been conducted which depicted the high sensitivity, in the four PRB's cases, of average pore water velocity within the barrier (v_r) v_r and K_r with the highest and the second-highest sensitivity index (SI) values towards t_R, respectively. The RSM-optimization revealed that Fe⁰ is the most feasible reactive material, comparing to the other considered materials, with respect to the optimal conditions regarding the long residency (t_R = 22 days) and low cost (b = 0.521 m), with around 95.2% desirability of its optimal solution. Overall, the current study represents a significant contribution and a vital step towards an accurate PRB's design based on previously determined optimal conditions.

Cr (VI) reduction by photocatalyic process: Nb2O5 an alternative catalyst

In this study, Nb₂O₅ catalyst was applied in the photocatalytic process for the Chromium reduction. Cr (VI) is a compound classified as highly toxic and often found in industrial tannery effluents. The techniques used for the photocatalytic material characterization were: X-ray diffraction, Specific surface area (B.E.T method), photo-acoustic spectroscopy, Scanning Electron Microscopy (SEM) and X-ray Dispersive Energy Spectrometry (EDS). A comparison between Nb₂O₅ and TiO₂ (widely used in photocatalytic reactions) indicated that Nb₂O₅ has 20% more Cr (VI) reduction than TiO₂. Tests carried out with Nb₂O₅ calcined at 500 °C and with non-calcined Nb₂O₅ showed that the heat treatment did not favor the reaction. Parameters such as pH, radiation intensity, initial concentration of Cr (VI) and amount of catalyst were studied. The results indicated that the acid (pH 2), emitted radiation intensity (250 W), initial concentration Cr (VI) at 10 mg L^-1 and 1.5 g L^-1 Nb₂O₅ non-calcined are the process optimal conditions. In addition, the reuse tests for Nb₂O₅ in consecutive cycles four, were realized. Photostability was maintained at approximately 90% for all cycles when Nb₂O₅ calcined was used. On the other hand, when using Nb₂O₅ non-calcined reduced by 21% during the four tests. This behavior is possibly due to the greater adsorption capacity of the non-calcined material. Making the Nb₂O₅ catalyst attractive for considering larger scale tests.

Performance of acid-activated water caltrop (Trapa natans) shell in fixed bed column for hexavalent chromium removal from simulated wastewater

The current study deals with the adsorption of hexavalent chromium using acid (H₃PO₄)-activated water caltrop (Trapa natans) shell (PWCS) using an up-flow packed bed column. Characteristics of breakthrough curve was obtained by investigating the effect of several operating parameters viz. inlet flow rate (2-6 mL/min), initial metal ion concentration (50-150 mg/L), and adsorbent's column bed height (1-3 cm). Elevated time of breakthrough curve was reported with elevated adsorbent bed height and vice versa with enhanced initial metal concentration and inlet flow rate of sorbate solution. Process design and breakthrough curves under varying conditions were predicted by applying column models like Thomas model, Adams-Bohart model, Yoon Nelson model, and bed depth service Time (BDST). Column behavior was better described by the BDST and Thomas model and simultaneously gave a good fit with the experimental data of breakthrough curves. The percentage removal for Cr(VI) from aqueous solution having pH 2 and temperature 303.15 K was observed to be 52.46%. The maximum adsorption capacity was found to be 87.31 mg/g according to the Thomas model. Conclusively, phosphoric acid-modified T. natans shell (PWCS) showed better sorption potential for of Cr(VI) species from simulated wastewater.

Abdullah A, Ozoemena KI, Elzatahry A. Unveiling Fabrication and Environmental Remediation of MXene-Based Nanoarchitectures in Toxic Metals Removal from Wastewater: Strategy and Mechanism

Efficient approaches for toxic metal removal from wastewater have had transformative impacts to mitigating freshwater scarcity. Adsorption is among the most promising purification techniques due to its simplicity, low cost, and high removal efficiency at ambient conditions. MXene-based nanoarchitectures emerged as promising adsorbents in a plethora of toxic metal removal applications. This was due to the unique hydrophilicity, high surface area, activated metallic hydroxide sites, electron-richness, and massive adsorption capacity of MXene. Given the continual progress in the rational design of MXene nanostructures for water treatment, timely updates on this field are required that deeply emphasize toxic metal removal, including fabrication routes and characterization strategies of the merits, advantages, and limitations of MXenes for the adsorption of toxic metals (i.e., Pb, Cu, Zn, and Cr). This is in addition to the fundamentals and the adsorption mechanism tailored by the shape and composition of MXene based on some representative paradigms. Finally, the limitations of MXenes and their potential future research perspectives for wastewater treatment are also discussed. This review may trigger scientists to develop novel MXene-based nanoarchitectures with well-defined shapes, compositions, and physiochemical merits for efficient, practical removal of toxic metals from wastewater.

Comparing the Adsorption Performance of Multiwalled Carbon Nanotubes Oxidized by Varying Degrees for Removal of Low Levels of Copper, Nickel and Chromium(VI) from Aqueous Solutions

Functionalized multiwalled carbon nanotubes (MWCNTs) have drawn wide attention in recent years as novel materials for the removal of heavy metals from the aquatic media. This paper investigates the effect that the functionalization (oxidation) process duration time (3 h or 6 h) has on the ability of MWCNTs to treat water contaminated with low levels of Cu(II), Ni(II) and Cr(VI) (initial concentrations 0.5–5 mg L−1) and elucidates the adsorption mechanisms involved. Adsorbent characterization showed that the molar ratio of C and O in these materials was slightly lower for the oxMWCNT6h, due to the higher degree of oxidation, but the specific surface areas and mesopore volumes of these materials were very similar, suggesting that prolonging the functionalization duration had an insignificant effect on the physical characteristics of oxidized multiwalled carbon nanotubes (oxMWCNTs). Increasing the Ph of the solutions from Ph 2 to Ph 8 had a large positive impact on the removal of Cu(II) and Ni(II) by oxMWCNT, but reduced the adsorption of Cr(VI). However, the ionic strength of the solutions had far less pronounced effects. Coupled with the results of fitting the kinetics data to the Elowich and Weber–Morris models, we conclude that adsorption of Cu(II) and Ni(II) is largely driven by electrostatic interactions and surface complexation at the interface of the adsorbate/adsorbent system, whereas the slower adsorption of Cr(VI) on the oxMWCNTs investigated is controlled by an additional chemisorption step where Cr(VI) is reduced to Cr(III). Both oxMWCNT3h and oxMWCNT6h have high adsorption affinities for the heavy metals investigated, with adsorption capacities (expressed by the Freundlich coefficient KF) ranging from 1.24 to 13.2 (mg g−1)/(mg l−1)n, highlighting the great potential such adsorbents have in the removal of heavy metals from aqueous solutions.

Nanomaterials in speciation analysis of metals and metalloids

Nanomaterials have draw extensive attention from the scientists in recent years mainly due to their unique and attractive thermal, mechanical and electronic properties, as well as high surface to volume ratio and the possibility for surface functionalization. Whereas mono functional nanomaterials providing a single function, the preparation of core/shell nanoparticles allows different properties to be combined in one material. Their properties have been extensively exploited in different extraction techniques to improve the efficiency of separation and preconcentration, analytical selectivity and method reliability. The aim of this paper is to provide an updated revision of the most important features and application of nanomaterials (metallic, silica, polymeric and carbon-based) for solid phase extraction and microextraction techniques in speciation analysis of some metals and metalloids (As, Cr, Sb, Se). Emphasis will be placed on the presentation of the most representative works published in the last five years (2015-2019).

A cationic Zr-based metal organic framework with enhanced acidic resistance for selective and efficient removal of CrO42−

A Zr-based cationic metal organic framework shows high acidic resistance and selectivity to the anion contaminant, CrO₄²⁻.