Biosorption of gold from computer microprocessor leachate solutions using chitin

Exploring the insights and benefits of biomass-derived sulfuric acid activated carbon for selective recovery of gold from simulated waste streams

The surging affluent in society, concomitant with increasing global demand for electrical and electronic devices, has led to a sharp rise in e-waste generation. E-wastes contain significant amounts of precious metals, such as gold, which can be recovered and reused, thus reducing the environmental impact of mining new metals. Selective recovery using sustainable and cost-effective materials and methods is therefore vital. This study undertook a detailed evaluation of low-cost biomass-derived activated carbon (AC) for selective recovery of Au from simulated e-waste streams. Utilizing high-performance synthesized H2SO4-AC, the adsorption mechanisms were explicated through a combination of characterization techniques, i.e., FE-SEM, BET, TGA, XRD, FTIR, XPS, and DFT simulations to conceptualize the atomic and molecular level interactions. Optimization of coordination geometries between model H2SO4-AC and anionic complexes revealed the most stable coordination for AuCl4- (binding energy, Eb = -4064.15 eV). The Au selectivity was further enhanced by reduction of Au(III) to Au(0), as determined by XRD and XPS. The adsorption reaction was relatively fast (∼5h), and maximum Au uptake reached 1679.74 ± 37.66 mg/g (among highest), achieved through adsorption isotherm experiments. Furthermore, a mixture of 0.5 M thiourea/1 M HCl could effectively elute the loaded Au and regenerate the spent AC. This study presents radical attempts to examine in detail, the synergistic effects of H2SO4 activation on biomass-derived ACs for selective recovery of Au from complex mixtures. The paper therefore describes a novel approach for the selective recovery of Au from e-wastes using multifunctional biomass-derived H2SO4-AC.

Optimized high-yield synthesis of chitin nanocrystals from shrimp shell chitin by steam explosion

This study attempted for the first time to prepare chitin nanocrystals (ChNCs) from shrimp shell chitin using steam explosion (SE) method. Response surface methodology (RSM) approach was used to optimize the SE conditions. Optimum SE conditions to acquire a maximum yield of 76.78 % were acid concentration (2.63 N), time (23.70 min), and chitin to acid ratio (1:22). Transmission electron microscopy (TEM) revealed the ChNCs produced by SE had an irregular spherical shape with an average diameter of 55.70 ± 13.12 nm. FTIR spectra showed ChNCs were slightly different than chitin due to a shift in peak positions to higher wavenumber and higher peak intensities. XRD patterns indicated ChNCs were a typical α-chitin structure. Thermal analysis revealed ChNCs were less thermally stable than chitin. Compared to conventional acid hydrolysis, the SE approach described in this study is simple, fast, easy, and requires less acid concentration and acid quantity, making it more scalable and efficient for synthesizing ChNCs. Furthermore, the characteristics of the ChNCs will shed light on the potential industrial uses for the polymer.

Ianăşi) P, Popa A, Lazău R, Negrea A, Negrea P, Duteanu N, Ciopec M, Nemes NS. Adsorbent Material Based on Carbon Black and Bismuth with Tunable Properties for Gold Recovery

Adsorption recovery of precious metals on a variety of solid substrates has steadily gained increased attention in recent years. Special attention was paid to the studies on the characterization of the adsorptive properties of materials with a high affinity for gold depending on the nature of the pendant groups present in the structure of the material. The aim of the present work was to synthesize and characterize a new material by using the sol-gel synthesis method (designated as BCb/CB). In this case, synthesis involved the following precursors: bismuth carbonate (III), carbon black, and IGEPAL surfactant (octylphenoxypolyethoxyethanol). Immobilization of the heterojunction as bismuth oxide over a flexible support such as carbon black (CB) can prevent their elution in solution and make it versatile for its use in a system. In this work, a new adsorbent material based on bismuth carbonate supported over carbon black (BCb/CB) was developed and used further for gold recovery from aqueous solutions. The required material was characterized physically/chemically by scanning electron microscopy (SEM); energy dispersive X-ray spectrometry (EDX); X-ray diffraction (XRD); thermal analysis (DTG/DTA); atomic force microscopy (AFM). The Brunauer-Emmett-Teller (BET) method was used to determine the specific surface area indicating a value of approximately 40 m²/g, higher than the surface of CB precursor (36 m²/g). The adsorptive properties and the adsorption mechanism of the materials were highlighted in order to recover Au(III). For this, static adsorption studies were carried out. The parameters that influence the adsorption process were studied, namely: the pH, the contact time, the temperature, and the initial concentration of the gold ions in the used solution. In order to establish the mechanism of the adsorption process, kinetic, thermodynamic, and equilibrium studies were carried out. Experimental data proved that the gold recovery can be conducted with maximum performance at pH 3, at room temperature. Thermodynamic studies proved that the gold adsorption on BCb/CB material is a spontaneous and endothermal process. The results indicate a total adsorption capacity of 13.1 mg Au(III)/g material. By using this material in real solutions, a recovery efficiency of 90.5% was obtained, concomitant with a higher selectivity (around 95%).

Starch, cellulose, pectin, gum, alginate, chitin and chitosan derived (nano)materials for sustainable water treatment: A review

Natural biopolymers, polymeric organic molecules produced by living organisms and/or renewable resources, are considered greener, sustainable, and eco-friendly materials. Natural polysaccharides comprising cellulose, chitin/chitosan, starch, gum, alginate, and pectin are sustainable materials owing to their outstanding structural features, abundant availability, and nontoxicity, ease of modification, biocompatibility, and promissing potentials. Plentiful polysaccharides have been utilized for making assorted (nano)catalysts in recent years; fabrication of polysaccharides-supported metal/metal oxide (nano)materials is one of the effective strategies in nanotechnology. Water is one of the world's foremost environmental stress concerns. Nanomaterial-adorned polysaccharides-based entities have functioned as novel and more efficient (nano)catalysts or sorbents in eliminating an array of aqueous pollutants and contaminants, including ionic metals and organic/inorganic pollutants from wastewater. This review encompasses recent advancements, trends and challenges for natural biopolymers assembled from renewable resources for exploitation in the production of starch, cellulose, pectin, gum, alginate, chitin and chitosan-derived (nano)materials.

Analysis of indium (III) adsorption from leachates of LCD screens using artificial neural networks (ANN) and adaptive neuro-fuzzy inference systems (ANIFS)

Ten different adsorbent materials were tested to adsorb indium (III) from leachates of LCD screens, aiming to concentrate this valuable material. Artificial neural network (ANN) and adaptive neuro-fuzzy inference system (ANIFS) were applied to analyze the indium (III) adsorption. The input variables for the network models were: specific surface area, point of zero charge, adsorbent dosage and contact time. Adsorption capacity (q) was used as output variable. The adsorption capacity values ranged from 8.203 to 1000 mg g^-1. The ANN modeling presented the best fit when the Levenberg-Marquardt algorithm was used. The ANFIS modeling presented the optimum performance when the hybrid method was used. Among the tested adsorbents, chitosan presented the best performance; attaining adsorption capacity of 1000 mg g^-1 within 20 min. This is an excellent value since the maximum indium concentration in LCD screens is 0.613 mg g^-1. This high capacity was attributed to the coordination ligation between chitosan and indium (III).

Challenges and opportunities in the recovery of gold from electronic waste

Rapid global technological development has led to the rising production of electronic waste that presents both challenges and opportunities in its recycling. In this review, we highlight the value of metal resources in the printed circuit boards (PCBs) commonly found in end-of-life electronics, the differences between primary (ore) mining applications and secondary ('urban') mining, and the variety of metallurgical separations, in particular those that have the potential to selectively and sustainably recover gold from waste PCBs.

Preparation of chitin nanowhiskers and its application for crystal violet dye removal from wastewaters

Chitin (Ch) and chitin nanowhiskers (ChNW) were prepared, characterized, and applied as adsorbent to remove crystal violet (CV) dye from aqueous solutions. Ch was obtained from shrimp wastes and submitted to acid hydrolysis in order to find ChNW. The increase in average pore size and the rod-like shape of ChNW were probably the main characteristics which contributed to the increase in adsorption potential, when compared with raw Ch. The adsorbent dosage considered more adequate was 5 g L^-1, and the most suitable pH was 8.0. A pseudo-second-order model was adequate to represent the kinetic profile. Sips and Hill models were suitable to fit the equilibrium curves. The maximum adsorption capacity of CV on ChNW was 59.52 mg g^-1, and the process was endothermic, favorable, and spontaneous. These findings indicated that ChNW have potential to be used as adsorbent in the treatment of colored wastewaters.

Biotechnological strategies for the recovery of valuable and critical raw materials from waste electrical and electronic equipment (WEEE) - A review

Critical raw materials (CRMs) are essential in the development of novel high-tech applications. They are essential in sustainable materials and green technologies, including renewable energy, emissionfree electric vehicles and energy-efficient lighting. However, the sustainable supply of CRMs is a major concern. Recycling end-of-life devices is an integral element of the CRMs supply policy of many countries. Waste electrical and electronic equipment (WEEE) is an important secondary source of CRMs. Currently, pyrometallurgical processes are used to recycle metals from WEEE. These processes are deemed imperfect, energy-intensive and non-selective towards CRMs. Biotechnologies are a promising alternative to the current industrial best available technologies (BAT). In this review, we present the current frontiers in CRMs recovery from WEEE using biotechnology, the biochemical fundamentals of these bio-based technologies and discuss recent research and development (R&D) activities. These technologies encompass biologically induced leaching (bioleaching) from various matrices,biomass-induced sorption (biosorption), and bioelectrochemical systems (BES).

Heavy metals uptake on Malpighia emarginata D.C. seed fiber microparticles: Physicochemical characterization, modeling and application in landfill leachate

Environmental heavy-metals contamination is a worldwide concern and the treatment of their sources constitutes a sustainable and efficient alternative. This work investigated the performance of Malpighia emarginataD.C. seed fibers microparticles (Me-SFMp) as biosorption platform for heavy metal ions. Integrated physicochemical analyses (FAAS, FTIR, SEM/EDS and XRF) showed that such ability was associated with the high microstructural porosity, wide surface area and diversity of functional groups on Me-SFMp structures, which favored the high and fast uptake of the target-substances (Cd, Zn, Cr, Pb, Cu and Ni ions). In terms of reactional kinetics, the pseudo-second order model showed better data correlation (R² from 0.9992 to 0.9998) and suggested the chemisorption as limiting step of the reaction mechanisms. From the Langmuir isotherms (R² from 0.9993 to 0.9998), it was observed that these phenomena occurred non-linearly on a homogeneous biosorbent monolayer. Me-SFMp can also be reused after desorption processes conducted in acid medium and, under ideal conditions (0.8 g biosorbent dosage; 100 mL of 1.00 mg L^-1 multi-metal solution adjusted to pH = 8.0; 300 rpm stirring speed; and 60 min contact time), the following maximum removal percentages order was observed for the first cycle: Cd (100%) = Zn (100%) > Cr (95.1%) > Pb (86.8%) > Cu (84.2%) > Ni (81.0%). The procedure was successfully applied to remove the studied heavy metal ions from raw landfill leachate, even in the presence of several (in)organic interferers, reinforcing the strong biosorbent-adsorbate interaction and the viability of this proposal.

Adsorption of valuable metals from leachates of mobile phone wastes using biopolymers and activated carbon

In this work, chitin (CTN), chitosan (CTS) and activated carbon (AC) were used as adsorbents to recover valuable metals from leachates of mobile phone wastes. The mobile phone wastes (contactors) were collected and characterized. The valuable metals were extracted by thiourea leaching. The adsorption of valuable metals from leachates was studied according to the kinetic and equilibrium viewpoints. It was found that the contactors were composed by Au, Ni, Cu and Sn. The thiourea leaching provided extraction percentages of 68.6% for Au, 22.1% for Ni and 2.8% for Cu. Sn was not extracted. The leachate presented 17.5 mg L^-1 of Au, 324.9 mg L^-1 of Ni and 573.1 mg L^-1 of Cu. The adsorption was fast, being the equilibrium attained within 120 min. The adsorption of Au, Ni and Cu onto CTN and AC followed the Langmuir model, while, the adsorption of these metals onto CTS, followed the Freundlich model. Removal percentages higher than 95% were obtained for all metals, depending of the type and amount of adsorbent. It was demonstrated that the adsorption onto chitin, chitosan and activated carbon can be an alternative to recover valuable metals from leachates of mobile phone wastes.

Electrochemical extraction of gold from wastes as nanoparticles stabilized by phospholipids

A simple one-step method for the extraction of gold from wastes as nanoparticles stabilized by phospholipids is demonstrated. This is achieved by applying an AC voltage for 5s to the gold-containing wastes, which act as the electrodes in a buffer solution containing a dispersed phospholipid (1,2-dioleoyl-sn-glycero-3-phosphocholine, DOPC). This is an environmentally friendly and rapid method for recovering gold from wastes. The extracted gold nanoparticles have significant potential as a catalyst or biomedical material.

Concentration of precious metals during their recovery from electronic waste

The rapid growth of electronic devices, their subsequent obsolescence and disposal has resulted in electronic waste (e-waste) being one of the fastest increasing waste streams worldwide. The main component of e-waste is printed circuit boards (PCBs), which contain substantial quantities of precious metals in concentrations significantly higher than those typically found in corresponding ores. The high value and limited reserves of minerals containing these metals makes urban mining of precious metals very attractive. This article is focused on the concentration and recovery of precious metals during pyro-metallurgical recycling of waste PCBs. High temperature pyrolysis was carried out for ten minutes in a horizontal tube furnace in the temperature range 800-1350°C under Argon gas flowing at 1L/min. These temperatures were chosen to lie below and above the melting point (1084.87°C) of copper, the main metal in PCBs, to study the influence of its physical state on the recovery of precious metals. The heat treatment of waste PCBs resulted in two different types of solid products, namely a carbonaceous non-metallic fraction (NMFs) and metallic products, composed of copper rich foils and/or droplets and tin-lead rich droplets and some wires. Significant proportions of Ag, Au, Pd and Pt were found concentrated within two types of metallic phases, with very limited quantities retained by the NMFs. This process was successful in concentrating several precious metals such as Ag, Au, Pd and Pt in a small volume fraction, and reduced volumes for further processing/refinement by up to 75%. The amounts of secondary wastes produced were also minimised to a great extent. The generation of precious metals rich metallic phases demonstrates high temperature pyrolysis as a viable approach towards the recovery of precious metals from e-waste.