Highly efficient removal of Cr(III)-poly(acrylic acid) complex by coprecipitation with polyvalent metal ions: Performance, mechanism, and validation

Effective oxidation decomplexation of Cu-EDTA and Cu2+ electrodeposition from PCB manufacturing wastewater by persulfate-based electrochemical oxidation: Performance and mechanisms

Complex wastewater matrices such as printed circuit board (PCB) manufacturing wastewater present a major environmental concern. In this work, simultaneous decomplexation of metal complex Cu-EDTA and reduction/electrodeposition of Cu2+ was conducted in a persulfate-based electrochemical oxidation system. Oxidizing/reductive species were simultaneously produced in this system, which realized 99.8% of Cu-EDTA decomplexation, 94.5% of Cu2+ reduction/electrodeposition under the conditions of original solution pH = 3.2, electrode distance = 3 cm, [Na2S2O8]0 = 5 mM, current density = 12 mA/cm2, and reaction time = 180 min. The total treatment cost is as low as 0.80 USD/mol Cu-EDTA. Effective mineralization (74.1% total organic carbon removal) of the solution was obtained after 3 h of treatment. •OH and SO4•- drove the Cu-EDTA decomplexation, destroying the chelating sites and finally it was effectively mineralized to CO2, H2O and Cu2+. The mechanisms of copper electrodeposition on the stainless steel cathode and persulfate activation by the BDD anode were proposed based on the electrochemical measurements. The electrodes exhibited excellent reusability and low metal (total iron and Ni2+) leaching during 20 cycles of application. This study provide an effective and sustainable method for the application of the electro-persulfate process in treating complex wastewater matrices.

Biochar-based microporous nanosheets-mediated nanoconfinement for high-efficiency reduction of Cr(VI)

Biochar-based materials have been widely used to remove Cr(VI). However, current strategies mainly focus on slow adsorption through electrostatic and functional group properties, ignoring the confinement catalytic fast kinetics caused by inherent porous properties. Herein, we designed a confinement strategy to achieve high-efficiency Cr(VI) reduction by encapsulating the catalytic reaction of Cr(VI) and oxalic acid (OA) in the micropore of PCRN-3-10-2-800. The results showed that the removal rate constant of the PCRN-3-10-2-800/OA system was 14.3 and 146.8 times higher than that of the BC-800/OA system (low porosity) and PCRN-3-10-2-800 alone (adsorption), which was highest removal rate constant in the current reported materials under the same system. The structure-activity relationship indicated that the catalytic activity of Cr(VI) depended on the micropore characteristics of the catalyst. Density functional theory calculations confirmed that nanoscale space could enhance Cr(VI) adsorption and reduce the energy barrier of the rate-determining step. The electron paramagnetic resonance spectrum demonstrated the rapid conversion of Cr(VI) to Cr(III). Furthermore, the PCRN-3-10-2-800/OA system showed good applicability and high efficiency for Cr(VI) removal (nearly 100% in 5 min) in industrial electroplating wastewater treatment. This work first proposes a nanoconfinement-induced heavy metal reduction strategy and guides biochar's universality design in wastewater treatment.

Construction of Core-shell Sb2 s3 @Cds Nanorod with Enhanced Heterointerface Interaction for Chromium-Containing Wastewater Treatment

How to collaboratively reduce Cr(VI) and break Cr(III) complexes is a technical challenge to solve chromium-containing wastewater (CCW) pollution. Solar photovoltaic (SPV) technology based on semiconductor materials is a potential strategy to solve this issue. Sb2 S3 is a typical semiconductor material with total visible-light harvesting capacity, but its large-sized structure highly aggravates disordered photoexciton migration, accelerating the recombination kinetics and resulting low-efficient photon utilization. Herein, the uniform mesoporous CdS shell is in situ formed on the surface of Sb2 S3 nanorods (NRs) to construct the core-shell Sb2 S3 @CdS heterojunction with high BET surface area and excellent near-infrared light harvesting capacity via a surface cationic displacement strategy, and density functional theory thermodynamically explains the breaking of SbS bonds and formation of CdS bonds according to the bond energy calculation. The SbSCd bonding interaction and van der Waals force significantly enhance the stability and synergy of Sb2 S3 /CdS heterointerface throughout the entire surface of Sb2 S3 NRs, promoting the Sb2 S3 -to-CdS electron transfer due to the formation of built-in electric field. Therefore, the optimized Sb2 S3 @CdS catalyst achieves highly enhanced simulated sunlight-driven Cr(VI) reduction (0.154 min-1 ) and decomplexation of complexed Cr(III) in weakly acidic condition, resulting effective CCW treatment under co-action of photoexcited electrons and active radicals. This study provides a high-performance heterostructured catalyst for effective CCW treatment by SPV technology.

Decreasing dissolved oxygen enhances in situ curtailment of intermediate Cr(VI) during photo-oxidative decomplexation of Cr(III)-EDTA

Cr(III)-organic complexes are stably presented in tanning, electroplating, and other industrial wastewaters, and their safe and efficient removal remains a current challenge. Available oxidation processes can remove Cr(III) complexes but readily result in highly toxic Cr(VI) accumulation. Herein, negligible Cr(VI) accumulation was achieved during photo-oxidation of Cr(III) complexes using a simple strategy of decreasing dissolved oxygen (DO). At the DO concentration of 5.0 mg·L^-1 or less, the in-process formation of intermediate Cr(VI) was totally abated by in situ formed reductive species, and total Cr was reduced from 9.0-11.0 mg·L^-1 to below 1.0 mg·L^-1. A complete curtailment of Cr(VI) was observed after 30-60 min at pH 6.0-9.0. Increasing Cr(III)-EDTA concentration and decreasing pH value facilitated the in situ reduction of intermediate Cr(VI). Based on the identification of intermediates and additional Cr(II) and quenching experiments, the possible key species involved in intermediate Cr(VI) reduction were the photogenerated Cr(II) and some C-centered radicals from Cr(III)-EDTA decomplexation, and the possible mechanisms of Cr(III)-EDTA decomplexation and intermediate Cr(VI) reduction were thus proposed. The process also showed efficient treatment on other Cr(III) complexes (citrate, oxalate, and tartrate) and realistic Cr(III) complexed wastewater. This study would provide an insignificant Cr(VI)-accumulated alternative for efficient and safe removal of Cr(III) complexes from contaminated water.

Interactions between Cr(VI) and the hydrochar: The electron transfer routes, adsorption mechanisms, and the accelerating effects of wood vinegar

Conversion of the low-valued invasive plant biomass into high-grade carbonaceous materials may provide a novel strategy to tackle the global issues of climate changes and exotic plant invasion. In this study, the hydrochar was fabricated from the biomass of Eupatorium adenophorum spreng. via hydrothermal carbonization (HTC) process to remove Cr(VI). The adsorption thermodynamics and kinetics were investigated via batch experiments, and the electron transfer routes and adsorption mechanisms were further revealed based on systematic characterization. The adsorption isotherms were well fitted by the Langmuir model with a maximum adsorption amount of 7.76 mg/g. The adsorption was spontaneous, and the surface adsorption and intraparticle diffusion may be the speed-limiting steps. Both -OH group and furan structures may donate the electrons to reduce Cr(VI), and the adsorption was governed by the surface complexation with the oxygen-containing functional groups including hydroxyl and carboxyl. Furthermore, the wood vinegar, as the by-product, can significantly accelerate the reduction rate of Cr(VI). Thus, this study provided a new strategy to fabricate carbonaceous materials which may facilitate to boost the carbon neutrality and control of invasive plants.

Coagulation characteristic and mechanism of Fe(III) salts toward typical Cr(III) complexes in wastewater treatment

Cr(III) complexes are typical pollutants in various industrial wastewater and pose a serious threat to the ecosystem and humans. The coagulation process is commonly used in water treatment plants, yet its removal characteristic and mechanism toward Cr(III) complexes have been rarely reported. In this study, the Fe(III) coagulation process was adopted for the evaluation of Cr(III) complex removal in terms of Cr residual concentration as well as floc size. The results showed that Fe(III) with a dose of 0.8 mM removed more than 80% of total Cr for Cr³⁺ and Cr(III)-acetate, whereas poor removal rate (~ 50%) was obtained for Cr(III)-citrate under the same conditions. Neutral and alkaline conditions facilitated Cr(III)-acetate removal by Fe(III) coagulation, while limited influence was observed for Cr(III)-citrate with various pH. The main removal mechanism of Cr(III)-acetate was precipitation. Cr(III)-citrate elimination largely relied on the adsorption property and sweeping effect of Fe floc. Moreover, Cr(III)-acetate was easier to be separated from a solution since the generated floc sizes were 270 μm. Flocs that formed in the Cr(III)-citrate treatment were only 0.3 μm, resulting in separation difficulties during the coagulation process. The presence of Cr(III)-acetate and Cr(III)-citrate caused a significant decline in membrane flux. This study provided fundamental knowledge of Fe coagulation treatment in Cr(III) complex-containing wastewater.

A novel synergistic covalence and complexation bridging strategy based on multi-functional biomass-derived aldehydes and Al(III) for engineering high-quality eco-leather

To get rid of the chrome pollution faced by the leather industry, we explored a novel engineering high-quality eco-leather technology based on the synergistic interactions between biomass-based aldehydes and Al(III). Firstly, dialdehyde xanthan gum (DXG) was prepared to covalently crosslink with the collagen fibers (CFs) via Schiff-base linkages under alkaline conditions, endowing the leather with a shrinkage temperature (Ts) of 80 °C and opening channels for the subsequent penetration of Al species (AL). Secondly, and for this latter purpose, the DXG-tanned leather was acidified to release part of the DXG from the leather according to the dynamic nature of the Schiff-base. Containing suitable oxygen-containing groups (OGs) with excellent complexation capabilities, the released DXG served as masking agents for AL, facilitating the penetration of AL into the inner CFs network for further complexation crosslinking. Consequently, a denser crosslinking network was constructed in the leather, and the crust leather exhibited higher Ts (82.2 °C), improved mechanical (tensile strength: 13.4 N/mm², tear strength: 53.3 N/mm) and organoleptic properties than those of the DXG crust or AL crust leathers. This demonstrates that this synergistic covalence and complexation bridging strategy is a sustainable option to substitute highly restricted chrome tanning agent for eco-leather production.

Adsorptive removal of Cr(III)-EDTA chelate from an aqueous solution by magnetic mesoporous silica microspheres

The 3-aminopropyltrimethoxysilane-modified magnetic mesoporous adsorbent (FNMs/APTES) was synthesized and applied to remove Cr(III)-EDTA chelates from water. The characterization of FNMs/APTES showed that the prepared adsorbent with a magnetic mesoporous structure was successfully grafted by APTES, which has good stability under acid conditions. The maximum capacities of FNMs/APTES for Cr(III)-EDTA adsorption at 15, 25 and 35 °C and pH 4.0 were 12.58, 13.13 and 14.00 mg·g^-1, respectively. The adsorption isotherm of FNMs/APTES for Cr(III)-EDTA conforms to the Freundlich model, and the adsorption kinetic model accords with the pseudo-second-order kinetic model. Adsorption of Cr(III)-EDTA on the adsorbent was not affected in the presence of Na⁺, K⁺ and Ca²⁺ even at 100 mmol·L^-1. Cr(III)-EDTA was anchored on FNMs/APTES through electrostatic interaction between protonated amino groups of adsorbents and Cr(III)-EDTA anions, and Cr(III)-EDTA chelates were adsorbed as a whole on the adsorbent. The Cr(III)-EDTA-saturated adsorbent can be readily regenerated in HCl solution and 83.03% of the initial Cr(III)-EDTA adsorption capacity remains after four adsorption-regeneration experiment cycles. The results highlighted that the FNMs/APTES as a potential adsorbent can be applied for the minimization of Cr(III)-EDTA chelates from water.

Iron-sulphur transformation control for enhancing Cr(VI) removal in flake and nanoscale porous pyrrhotite (Fe7S8) added wastewater

Hexavalent chromium (Cr(VI)) contaminated wastewater should be addressed efficiently in the environmental field. In previous applications, nano iron sulfides amendment has not been well controlled for iron-sulfur transformation. In this study, the novel flake and nanoscale porous pyrrhotite (Fe₇S₈) (FNPP) amendment was synthesized. The iron-sulphur transformation of FNPP was controlled and optimized for enhancing Cr(VI) removal. The specific surface area and average pore diameter of the FNPP amendment reached 115.7 m²/g and 2.1 nm. The maximum adsorption capacity of total chromium reached 66.3 mg/g. The optimized iron-sulphur transformation condition was an initial FNPP and Cr(VI) molar ratio of 8, pH at 5.6, in which the Cr(VI) removal reached 96.5% and all producing S^2- was utterly consumed. It is confirmed that S^2- fast induced Fe³⁺/Fe²⁺ circulation and FNPP has a speedier adsorption rate for Cr(III) than Cr(VI). Fe²⁺ and S^2- mediated the Cr(VI) reduction to Cr(III), thus, much faster Cr(VI) removal was achieved. High efficiency removal mechanism of Cr(VI) was combined with surface adsorption/reduction and solution reduction/precipitation. The research demonstrated that controlling and optimizing the iron-sulphur transformation of Fe₇S₈ amendment can significantly enhance Cr(VI) removal.

Reductive immobilization of Cr(VI) in contaminated water by tannic acid

The rapid reductive immobilization of Cr(VI) from the aqueous solution was achieved by reduction to Cr(III) using tannic acid (TA), and subsequent pH-triggering precipitation of the organo-Cr(III) complexes formed in the redox reaction. The effects of TA concentration, temperature, and solution pH on the reduction of Cr(VI) were examined by batch experiments, and the rapid redox reduction followed a second-order kinetics with respect to Cr(VI) concentration in the pH range of 2.0-3.0. UV-visible spectra, FTIR, and XPS confirmed the complete detoxification of Cr(VI) concomitant with carboxylation of partial phenolic hydroxyls in TA. Synchronously, the reduced Cr(III) coordinated with carboxyl groups in oxidized TA (OTA) to form complexes, which exhibited remarkable pH-dependent size distribution characteristics as illustrated by SEM images and sequential filtration/ultrafiltration. The resulted Cr(III) complexes could aggregate into colloids with larger size and precipitate out at pH range of 6.0-8.0 via cross-linking, thereby leading to 93% Cr and 89% TOC immobilization. An eco-friendly and cost-effective method for Cr(VI) elimination and immobilization is provided because polyphenols are natural polymers derived from plants.

Spatial distribution and morphological transformation of chromium with coexisting substances in tannery landfill

The prosperity and development of tannery industry have brought about rapid economic growth. However, the tannery landfill without anti-seepage measures in the early stage has generated masses of environmental hazards owing to the lack of awareness in environmental protection. Therefore, it is imperative to pay much attention to the understanding of environmental hazards from tannery waste. In this study, solid samples and groundwater samples were collected from a tannery landfill to study the effect of the characteristic pollutants produced by tanning on chromium distribution with other coexisting substances. The results showed that significant correlations were demonstrated between multiple coexisting substances (total organic carbon, total petroleum hydrocarbons, total nitrogen, Cr, F, Ca, Cu and Pb), indicating the possible same source or they coming from the same tannery production stage. The weights of positive effects and negative effects of coexisting substances on total Cr distribution in the profile decreased in the order: total nitrogen > Cu > Ca > Pb > total organic carbon > F > SO₄^2-> Cd, and Ni > Cl > Hg, respectively. Moreover, the simulation of Visual MINTEQ showed that the cations were mainly bound to Cr as CrO₄^2-, while the anions were bound to Cr³⁺. This study provided a new perspective on the selection of remediation strategies for Cr-contaminated sites to avoid secondary environmental pollution caused by the release of coexisting heavy metals.

Nanomaterials: Synthesis and Applications in Theranostics

Nanomaterials are endowed with unique features and essential properties suitable for employing in the field of nanomedicine. The nanomaterials can be classified as 0D, 1D, 2D, and 3D based on their dimensions. The nanomaterials can be malleable and ductile and they can be drawn into wires and sheets. Examples of nanomaterials are quantum dots (0D), nanorods, nanowires (1D), nanosheets (2D), and nanocubes (3D). These nanomaterials can be synthesized using top-down and bottom-up approaches. The achievements of 0D and 1D nanomaterials are used to detect trace heavy metal (e.g., Pb2+) and have higher sensitivity with the order of five as compared to conventional sensors. The achievements of 2D and 3D nanomaterials are used as diagnostic and therapeutic agents with multifunctional ability in imaging systems such as PET, SPECT, etc. These imaging modalities can be used to track the drug in living tissues. This review comprises the state-of-the-art of the different dimensions of the nanomaterials employed in theranostics. The nanomaterials with different dimensions have unique physicochemical properties that can be utilized for therapy and diagnosis. The multifunctional ability of the nanomaterials can have a distinct advantage that is used in the field of theranostics. Different dimensions of the nanomaterials would have more scope in the field of nanomedicine.

Confining polyacrylic acid on the surface of nanoscale zero-valent iron by aluminum hydroxide for in-situ anti-passivation

Aggregation and surface passivation of nanoscale zero-valent iron (NZVI) particles have limited their reactivity and application for environmental remediation. In this study, an aluminum hydroxide/polyacrylic acid (Al(OH)₃/PAA) hybrid shell was homogeneously coated on the NZVI surface to overcome the limitations. PAA molecules were confined onto the NZVI surface by hydration of Al(III) cations. The Al(OH)₃/PAA coating shell provided more electrostatic repulsion forces between NZVI particles to hinder the particle aggregation and preserve the NZVI reactivity. On the other hand, the surface-anchored PAA provided a thickened reactive layer for Cr(VI) reduction. Besides, XPS and TEM results showed that the surface carboxylic groups bound produced Cr(III) and Fe(III) cations and inhibited the precipitation of hydroxides on the NZVI surface. The reduced passivation layer increased the longevity of NZVI for surface reactions. As a result, the 24-h Cr(VI) reduction capacity of NZVI particles was improved from 49.4 to 92.6 mg/g with a 2 wt% (Al/Fe) Al(OH)₃/PAA coating shell. Overall, this study presented a promising strategy to effectively tune the surface properties of nanoparticles and improve the feasibility of NZVI for environmental remediation.

Smart Adsorbents for Aquatic Environmental Remediation

A noticeable interest and steady rise in research studies reporting the design and assessment of smart adsorbents for sequestering aqueous metal ions and xenobiotics has occurred in the last decade. This motivates compiling and reviewing the characteristics, potentials, and performances of this new adsorbent generation's metal ion and xenobiotics sequestration. Herein, stimuli-responsive adsorbents that respond to its media (as internal triggers; e.g., pH and temperature) or external triggers (e.g., magnetic field and light) are highlighted. Readers are then introduced to selective adsorbents that selectively capture materials of interest. This is followed by a discussion of self-healing and self-cleaning adsorbents. Finally, the review ends with research gaps in material designs.

A critical review on metal complexes removal from water using methods based on Fenton-like reactions: Analysis and comparison of methods and mechanisms

Metals mainly exist in the form of complexes in urban wastewater, fresh water and even drinking water, which are difficult to remove and further harm human health. Fenton-like reaction has been used for the removal of metal complexes. Effective removal of metal complexes using Fenton-like reaction requires the removal of both metals and organic ligands, meanwhile, the fate of metals and organic pollutions must be clearly understood. Thus, this review summarizes the relevant research on metal complex removal from using Fenton-like reactions in the past ten years, with the detailed removal approaches and mechanisms analyzed. Electro-, photo-, microwave/ultrasound-Fenton reactions or the synergistic Fenton reaction have been shown to exhibit excellent metal complex treatment capabilities. Furthermore, various catalysts, such as transition metals, bimetals and metal-free catalytic systems can expand the potential applications of Fenton-like reactions. Novel Fenton reaction methods without the addition of metals or H₂O₂, with construction of a dual active center catalyst, or with the introduction of other free radicals, are all worthy of further investigation. Due to increasing levels of environmental metal and organic pollutions remediation requirements, more research is required for the development of economical and efficient novel Fenton-like processes.

Effect of Cr (III) on hydration, microstructure of magnesium phosphate cement, and leaching toxicity evaluation

The pollution caused by chromium and its compounds has caused severe harm to the environment, and waste stabilization/solidification containing these contaminants by magnesium phosphate cement (MPC) is one of the best ways to address this problem. If the mechanism between Cr³⁺ and MPC can be understood, it will significantly improve the latter's solidification performance with respect to ameliorating Cr pollution. In this paper, the compressive strength, microstructure, pH in the process of sample hydration, and leaching toxicity of solidified forms were studied by adding various amounts of Cr³⁺ into MPC. The setting time of MPC decreased at first and then increased as the Cr³⁺ concentration increased. The added Cr³⁺ reacted with the phosphate ions to form mineral phases, which changed the MPC matrix structure. The matrix's compressive strength was higher when the M/P ratio (MgO/KH₂PO₄ mass ratio) was smaller. When the concentration of Cr³⁺ was constant, and the M/P ratio was low (< 4:1), the matrix's compressive strength increased as the M/P ratio increased. The presence of Cr³⁺ changed the system's pH and affected the hydration products' morphology; this trend strengthened as the Cr³⁺ concentration increased. The highest leaching concentration of Cr³⁺ was 0.255 mg/L, and the concentration decreased as the M/P ratio decreased. During solidification, the appropriate proportion of MPC can be selected according to the concentration of Cr³⁺ to achieve better solidification performance.