Legacy and novel perfluoroalkyl and polyfluoroalkyl substances in industrial wastewater and the receiving river water: Temporal changes in relative abundances of regulated compounds and alternatives

Occurrence and profiles of perfluoroalkyl substances in wastewaters of chemical industrial parks and receiving river waters: Implications for the environmental impact of wastewater discharge

A total of 17 groups of wastewaters from the chemical industrial parks and matched receiving river waters were collected in the east of China. The measured total concentrations of 21 analyzed PFAS analogues (∑21PFAS) in the influents and effluents of the wastewater treatment plants (WWTPs) were in the range of 0.172-20.6 μg/L (mean: 18.2 μg/L, median: 3.9 μg/L) and 0.167-93.6 μg/L (mean: 10.8 μg/L, median: 1.12 μg/L), respectively, which were significantly higher than those observed in the upstream (range: 0.0158-7.05 μg/L, mean: 1.09 μg/L, median: 0.482 μg/L) and downstream (range: 0.0237-1.82 μg/L, mean: 0.697 μg/L, median: 0.774 μg/L) receiving waters. Despite the concentrations and composition profiles of PFAS varied in the water samples from different sampling sites, PFOA was generally the major PFAS analogue in the research areas, mainly due to the history of PFOA production and usage as well as the specific exemptions. The calculated concentration ratios of the short-chain PFCAs and PFSAs to their respective predecessors (PFOA and PFOS) in most of the samples far exceeded 1, indicating a shift from legacy PFOA and PFOS to short-chain PFAS in the research areas. Correlation network analysis and the calculated concentration ratios of PFAS in the effluents versus influents indicated transformation may have occurred during the water treatment processes and PFAS could not be efficiently removed in the WWTPs. Wastewater discharge of chemical industrial parks is a vital source of PFAS dispersed into the aquatic environment.

Effects of long-chained perfluoroalkyl acids (PFAAs) on the uptake and bioaccumulation of short-chained PFAAs in two free-floating macrophytes: Eichhornia crassipes and Ceratophyllum demersum

Short-chained perfluoroalkyl acids (PFAAs, CnF2n+1-R, n ≤ 6) have merged as global concerns due to their extensive application and considerable toxicity. However, long-chained PFAAs (n ≥ 7) featured with high persistence are still ubiquitously observed in aquatic environment. To understand the uptake behavior of short-chained PFAAs in aquatic macrophytes, the uptake kinetics, bioconcentration, and translocation of short-chained PFAAs (3 ≤n ≤ 6) in two typical free-floating macrophytes (Eichhornia crassipes and Ceratophyllum demersum) were investigated in the treatments with and without long-chained PFAAs (7 ≤n ≤ 11). Results showed that short-chained PFAAs can be readily accumulated in both E. crassipes and C. demersum, and the uptake of short-chained PFAAs fit the two-compartment kinetic model well (p < 0.05). In the treatments with long-chained PFAAs, significant concentration decreases of all concerned short-chained PFAAs in E. crassipes and PFAAs with n ≤ 5 in C. demersum were observed. Long-chained PFAAs could hinder the uptake rates, bioconcentration factors, and translocation factors of most short-chained PFAAs in free-floating macrophytes (p < 0.01). Significant correlations between bioconcentration factors and perfluoroalkyl chain length were only observed when long-chained PFAAs were considered (p < 0.01). Our results underlined that the effects of long-chained PFAAs should be taken into consideration in understanding the uptake and bioaccumulation behaviors of short-chained PFAAs.

Per- and polyfluoroalkyl substances (PFASs) in bivalve molluscs from Shandong Province, China: Occurrence, distribution, and implications for human consumption

We examined the occurrence and levels of 19 legacy and emerging per- and polyfluoroalkyl substances (PFASs) in 7 species of marine bivalve molluscs collected from four coastal cities of Shandong Province, China. Perfluorooctanoic acid (PFOA) was the most prevalent component, accounting for 68.1 % of total PFASs. The total PFASs in bivalve molluscs ranged from 0.86 to 6.55 ng/g wet weight, with the highest concentration found in Meretrix meretrix L. The concentration of total PFASs in bivalve molluscs showed the following trend: clams > scallops > oysters > mussels. Estimation on the human intake of PFASs from consumption of bivalve molluscs resulted in hazard ratios (HR) ranging from 0.12 to 6.40. Five of the seven species had HR >1, indicating high exposure risks associated with PFASs. Therefore, the occurrence of PFASs in marine biota is particularly concerning and further investigations on the sources of PFASs in Shandong are warranted.

Occurrence, bioaccumulation, fate, and risk assessment of emerging pollutants in aquatic environments: A review

Significant concerns on a global scale have been raised in response to the potential adverse impacts of emerging pollutants (EPs) on aquatic creatures. We have carefully reviewed relevant research over the past 10 years. The study focuses on five typical EPs: pharmaceuticals and personal care products (PPCPs), per- and polyfluoroalkyl substances (PFASs), drinking water disinfection byproducts (DBPs), brominated flame retardants (BFRs), and microplastics (MPs). The presence of EPs in the global aquatic environment is source-dependent, with wastewater treatment plants being the main source of EPs. Multiple studies have consistently shown that the final destination of most EPs in the water environment is sludge and sediment. Simultaneously, a number of EPs, such as PFASs, MPs, and BFRs, have long-term environmental transport potential. Some EPs exhibit notable tendencies towards bioaccumulation and biomagnification, while others pose challenges in terms of their degradation within both biological and abiotic treatment processes. The results showed that, in most cases, the ecological risk of EPs in aquatic environments was low, possibly due to potential dilution and degradation. Future research topics should include adding EPs detection items for the aquatic environment, combining pollution, and updating prediction models.

Environmental occurrence, bioaccumulation and human risks of emerging fluoroalkylether substances: Insight into security of alternatives

Per- and polyfluoroalkyl substances (PFASs) are widely used due to their unique structure and excellent performance, while also posing threats on ecosystem, especially long-chain perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA). As the control of conventional PFASs, fluoroalkylether substances (ether-PFASs) as alternatives are constantly emerging. Subsequently, the three representative ether-PFASs, chlorinated polyfluoroalkyl ether sulfonic acid (F-53B), hexafluoropropylene oxide-dimer acid (HFPO-DA), and 4,8-Dioxa-3H-perfluorononanoicacid (ADONA) are discovered and have received more attention in the environment and ecosystem. But their security is now also being challenged. This review systematically assesses their security from six dimensions including environmental occurrence in water, soil and atmosphere, as well as bioaccumulation and risk in plants, animals and humans. High substitution level is observed for F-53B, whether in environment or living things. Like PFOS or even more extreme, F-53B exhibits high biomagnification ability, transmission efficiency from maternal to infant, and various biological toxicity effects. HFPO-DA still has a relatively low substitution level for PFOA, but its use has emerged in Europe. Although it is less detected in human bodies and has a higher metabolic rate than PFOA, the strong migration ability of HFPO-DA in plants may pose dietary safety concerns for humans. Research on ADONA is limited, and currently, it is detected in Germany frequently while remaining at trace levels globally. Evidently, F-53B has shown increasing risk both in occurrence and toxicity compared to PFOS, and HFPO-DA is relatively safe based on available data. There are still knowledge gaps on security of alternatives that need to be addressed.

Interactions between MPs and PFASs in aquatic environments: A dual-character situation

Microplastics (MPs) and per- and polyfluoroalkyl substances (PFASs) have drawn great attention as emerging threats to aquatic ecosystems. Although the literature to study the MPs and PFASs alone has grown significantly, our knowledge of the overlap and interactions between the two contaminations is scarce due to the unawareness of it. Actually, numerous human activities can simultaneously release MPs and PFASs, and the co-sources of the two are common, meaning that they have a greater potential for interactions. The direct interaction lies in the PFASs adsorption by MPs in water with integrated mechanisms including electrostatic and hydrophobic interactions, plus many influence factors. In addition, the existence and transportation of MPs and PFASs in the aquatic environment have been identified. MPs and PFASs can be ingested by aquatic organisms and cause more serious combined toxicity than exposure alone. Finally, curbing strategies of MPs and PFASs are overviewed. Wastewater treatment plants (WWTPs) can be an effective place to remove MPs from wastewater, while they are also an important point source of MPs pollution in water bodies. Although adsorption has proven to be a successful curbing method for PFASs, more technological advancements are required for field application. It is expected that this review can help revealing the unheeded relationship and interaction between MPs and PFASs in aquatic environments, thus assisting the further investigations of both MPs and PFASs as a whole.

Metal-Organic Framework-Based Composites for the Adsorption Removal of Per- and Polyfluoroalkyl Substances from Water

The increasing health risks posed by per- and polyfluoroalkyl substances (PFASs) in the environment highlight the importance of implementing effective removal techniques. Conventional wastewater treatment processes are inadequate for removing persistent organic pollutants. Recent studies have increasingly demonstrated that metal-organic frameworks (MOFs) are capable of removing PFASs from water through adsorption techniques. However, there is still constructive discussion on the potential of MOFs in adsorbing and removing PFASs for large-scale engineering applications. This review systematically investigates the use of MOFs as adsorbents for the removal of PFAS in water treatment. This primarily involved a comprehensive analysis of existing literature to understand the adsorption mechanisms of MOFs and to identify factors that enhance their efficiency in removing PFASs. We also explore the critical aspects of regeneration and stability of MOFs, assessing their reusability and long-term performance, which are essential for large-scale water treatment applications. Finally, our study highlights the challenges of removing PFASs using MOFs. Especially, the efficient removal of short-chain PFASs with hydrophilicity is a major challenge, while medium- to long-chain PFASs are frequently susceptible to being captured from water by MOFs through multiple synergistic effects. The ion-exchange force may be the key to solving this difficulty, but its susceptibility to ion interference in water needs to be addressed in practical applications. We hope that this review can provide valuable insights into the effective removal and adsorption mechanisms of PFASs as well as advance the sustainable utilization of MOFs in the field of water treatment, thereby presenting a novel perspective.

Background concentrations and spatial distribution of PFAS in surface waters and sediments of the greater Melbourne area, Australia

A survey of per- and polyfluoroalkyl substances (PFAS) was conducted in Melbourne, Australia to determine background concentrations in residential, industrial, municipal wastewater treatment plants, and rural land uses. Surface water and sediment samples collected from 65 sites with different catchment land uses were analysed for thirty-three PFAS. Twenty-two out of thirty-three targeted PFAS were detected, with at least one PFAS species was detected in 98% water samples and 8% sediment samples. One site was determined to have point-source pollution from an airport (surface water Σ33PFAS = 4261 ng/L) and was excluded from statistical analyses. The median Σ33PFAS concentration in surface water was 63.5 ng/L and the average was 78.6 ng/L (range < DL-526 ng/L). PFAS species with the highest median concentrations were PFBA (11.3 ng/L), PFHxA (9.2 ng/L), PFOA (8.3 ng/L), PFOS (8.0 ng/L), PFPeA (7.5 ng/L), PFHpA (3.2 ng/L), and PFHxS (2.9 ng/L). The average Σ4PFAS in sediments was 0.35 ng/g d.w. (range = Collapse

Key Words

• FTS
• Land use
• PFAS
• PFOA
• PFOS
• Urban

Collapse

MESH Headings

• Environmental Monitoring
• Water Pollutants, Chemical/analysis
• Fluorocarbons/analysis
• Hydrocarbons, Fluorinated/analysis
• Water/analysis
• Australia
• Alkanesulfonic Acids/analysis

Collapse

Grants Collapse

Affiliation(s)

Tanya Paige Aquatic Environmental Stress (AQUEST) Research Group, RMIT University, PO Box 71, Bundoora, Victoria, 3083, Australia.
Thishakya De Silva National Measurement Institute, 1/153 Bertie St, Port Melbourne, Victoria, 3207, Australia
Saman Buddhadasa National Measurement Institute, 1/153 Bertie St, Port Melbourne, Victoria, 3207, Australia
Shiva Prasad National Measurement Institute, 105 Delhi Rd, North Ryde, NSW, 2113, Australia
Dayanthi Nugegoda Aquatic Environmental Stress (AQUEST) Research Group, RMIT University, PO Box 71, Bundoora, Victoria, 3083, Australia
Vincent Pettigrove Aquatic Environmental Stress (AQUEST) Research Group, RMIT University, PO Box 71, Bundoora, Victoria, 3083, Australia

Collapse

Enhanced removal of short- and long-chain per- and poly-fluoroalkyl substances from aqueous phase using crushed grafted chitosan beads: Performance and mechanisms

The widespread use of per- and poly-fluoroalkyl substances (PFASs), environmentally persistent halogenated hydrocarbons, in various industrial and commercial applications has caused significant concerns owing to their contamination of soil and groundwater. Chitosan is a biopolymer substance with abundant amine and hydroxyl functional groups, making it a good candidate for adsorption of PFASs. This study aimed to increase chitosan's adsorption capacity by grafting additional amine functional groups on its surface for the removal of long- and short-chain PFASs from an aqueous phase. Two types of chitosan-based sorbents were developed: crushed chitosan beads (CBs) and polyethyleneimine-grafted CBs (GCBs). Batch adsorption tests assessed the adsorption capacities of the sorbents in terms of the sorption kinetics, isotherms, selectivity, and reusability. Based on the results, the GCBs had significant potential for adsorbing PFASs. These capacities were significantly higher than those demonstrated by the CBs. The sorption kinetics data revealed that the GCBs had a fast sorption rate. Furthermore, the GCBs demonstrated a high adsorption affinity, with log Kd values ranging from 1.5 to 2.5 for PFASs at environmentally relevant concentrations (1000 ng L-1). They also demonstrated excellent selectivity sorption for these compounds, even in the presence of other organic and inorganic pollutants.

The significance of fluorinated compound chain length, treatment technology, and influent composition on per- and polyfluoroalkyl substances removal in worldwide wastewater treatment plants

Wastewater treatment plants (WWTPs) are deemed major conveyors and point sources of per- and polyfluoroalkyl substances (PFAS) to the environment. This statistical meta-analysis of existing literature from the past 15 years focused on the significance of treatment type for PFAS removal efficiencies and the influence of PFAS sources (domestic vs. industrial) on their removal. Different sampling events, WWTPs across the world, different treatment technologies, configurations, and processes, as well as different PFAS classes and compounds were considered. This study evaluated 13 PFAS analyzed predominantly in 161 WWTPs across the world. The statistical test results revealed that these 13 frequently detected and reported PFAS can be divided into four groups based on their behavior during wastewater treatment, namely (1) C6-10 perfluorocarboxylic acids (PFCAs), (2) C4,5,11,12 PFCAs, (3) C4,6,8 perfluoroalkane sulfonic acids (PFSAs), and (4) C10 PFSA. In this study, biological treatments such as (1) membrane bioreactors, (2) combination of two or more biological treatments, and (3) biofilm processes revealed the highest PFAS removals, although the addition of a tertiary treatment actually had a nonbeneficial effect on PFAS removal. Moreover, a strong statistical correlation was observed between industrial wastewater sources and the presence of high influent PFAS concentrations in the receiving WWTPs. This indicates that industrial sources were the main contributors of the PFAS load in the analyzed WWTPs. Integr Environ Assess Manag 2024;20:59-69. © 2023 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals LLC on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Occurrence of per- and polyfluorinated alkyl substances in wastewater treatment plants in Northern Italy

Wastewater treatment plants are known to be relevant input sources of per- and polyfluoroalkyl substances (PFAS) in the aquatic environment. This study aimed to investigate the occurrence, fate, and seasonal variability of twenty-five PFAS in four municipal wastewater treatment plants (WWTP A, B, C, and D) surrounding the city of Milan (Northern, Italy). Composite 24-h wastewater samples were collected in July and October 2021 and May and February 2022 from influents and effluents of the four WWTPs. PFAS were detected at concentrations ranging between 24.1 and 66.9 μg L-1 for influent and 13.4 and 107 μg L-1 for effluent wastewater samples. Perfluoropentanoic acid was the most abundant (1.91-30.0 μg L-1) in influent samples, whereas perfluorobutane sulfonic acid predominated (0.80-66.1 μg L-1) in effluent samples. In sludge, PFOA was detected in plant A at concentrations in the range of 96.6-165 ng kg-1 dw in primary sludge samples and 98.6-440 ng kg-1 dw in secondary treatment sludge samples. The removal efficiency of total PFAS varied between 6 % and 96 %. However, an increase of PFAS concentrations was observed from influents to effluents for plant D (during July and October), plant A (during October and May), and plant C (during May) indicating that biotransformation of PFAS precursors can occur during biological treatments. This was supported by the observed increase in concentrations of PFOA from primary to secondary treatment sludge samples in plant A. Moreover, the plant operating at shorter hydraulic retention times (plant D) showed lower removal efficiency (<45 %). Seasonal variation of PFAS in influent and effluent appears rather low and more likely due to pulse release instead of seasonal factors.

Toward systematic understanding of adsorptive removal of legacy and emerging per-and polyfluoroalkyl substances (PFASs) by various activated carbons (ACs)

Per-and polyfluoroalkyl substances (PFASs) have received great attention due to their persistence, bioaccumulation and toxicity. Various activated carbons (ACs) exhibit wide variability in adsorptive performance towards PFASs. In order to gain a systematic understanding of adsorptive removal of legacy and emerging PFASs by ACs, the adsorption of ten PFASs on various ACs was comprehensively investigated. Results showed that granular activated carbon-1 (GAC-1) and powdered activated carbon-1 (PAC-1) removed more than 90% of all target PFASs. Particle size, surface charge, and micropores quantity of ACs were closely related to their performance for PFASs removal. Electrostatic interaction, hydrophobic interaction, surface complexation and hydrogen bonding were the adsorption mechanisms, with hydrophobic interaction being the predominant adsorptive force. Physical and chemical adsorption were both involved in PFAS adsorption. The removal rates of PFASs by GAC-1 decreased from 93%-100% to 15%-66% in the presence of 5 mg/L fulvic acid (FA). GAC was able to remove more PFASs under acidic medium, whereas PAC removed hydrophobic PFASs better under the neutral medium. The removal rates of PFASs by GAC-3 increased significantly from 0%-21% to 52%-97% after being impregnated with benzalkonium chlorides (BACs), demonstrating the superiority of this modification method. Overall, this study provided theoretical support for removing PFASs from water phase with ACs.

Occurrences and fates of per- and polyfluoralkyl substances in textile dyeing wastewater along full-scale treatment processes

Industrial wastewater is a substantial source of per- and polyfluoroalkyl substances (PFASs) in the environment. However, very limited information is available on the occurrences and fates of PFASs along industrial wastewater treatment processes, particularly for the textile dyeing industry where PFASs occur extensively. Herein, the occurrences and fates of 27 legacy and emerging PFASs were investigated along the processes of three full-scale textile dyeing wastewater treatment plants (WWTPs) based on UHPLC-MS/MS in combination with self-developed solid extraction protocol featuring selective enrichment for ultrasensitive analysis. The total PFASs ranged at 630-4268 ng L-1 in influents, 436-755 ng L-1 in effluents, and 91.5-1182 μg kg-1 in the resultant sludge. PFAS species distribution varied among WWTPs, with one WWTP dominated by legacy perfluorocarboxylic acids while the other two dominated by emerging PFASs. Perfluorooctane sulfonate (PFOS) was trivial in the effluents from all the three WWTPs, indicating its diminished use in textile industry. Various emerging PFASs were detected at different abundances, demonstrating their use as alternatives to legacy PFASs. Most conventional processes of the WWTPs were inefficient in removing PFASs, especially for the legacy PFASs. The microbial processes could remove the emerging PFASs to different extents, whereas commonly elevated the concentrations of legacy PFASs. Over 90% of most PFASs could be removed by reverse osmosis (RO) and was enriched into the RO concentrate accordingly. The total oxidizable precursors (TOP) assay revealed that the total concentration of PFASs was increased by 2.3-4.1 times after oxidation, accompanied by formation of terminal perfluoroalkyl acids (PFAAs) and degradation of emerging alternatives to various extents. This study is believed to shed new light on the monitoring and management of PFASs in industries.

An overview on human exposure, toxicity, solid-phase microextraction and adsorptive removal of perfluoroalkyl carboxylic acids (PFCAs) from water matrices

Perfluoroalkyl carboxylic acids (PFCAs) are sub-class of perfluoroalkyl substances commonly detected in water matrices. They are persistent in the environment, hence highly toxic to living organisms. Their occurrence at trace amount, complex nature and prone to matrix interference make their extraction and detection a challenge. This study consolidates current advancements in solid-phase extraction (SPE) techniques for the trace-level analysis of PFCAs from water matrices. The advantages of the methods in terms of ease of applications, low-cost, robustness, low solvents consumption, high pre-concentration factors, better extraction efficiency, good selectivity and recovery of the analytes have been emphasized. The article also demonstrated effectiveness of some porous materials for the adsorptive removal of the PFCAs from the water matrices. Mechanisms of the SPE/adsorption techniques have been discussed. The success and limitations of the processes have been elucidated.

Joint toxicity mechanisms of perfluorooctanoic acid and sulfadiazine on submerged macrophytes and periphytic biofilms

Hazardous chemicals, such as perfluoroalkyl substances (PFASs) and antibiotics, coexist in aquatic environments and pose a severe threat to aquatic organisms. However, research into the toxicity of these pollutants on submerged macrophytes and their periphyton is still limited. To assess their combined toxicity, Vallisneria natans (V. natans) was exposed to perfluorooctanoic acid (PFOA) and sulfadiazine (SD) at environmental concentrations. Photosynthetic parameters such as chlorophyll a, chlorophyll b, total chlorophyll, and carotenoids were lower in the SD exposure group, indicating that SD had a significant effect on the photosynthesis of aquatic plants. Single and combined exposures effectively induced antioxidant responses, with increases in superoxide dismutase, peroxidase activities, and ribulose-1,5-bisphosphate carboxylase concentrations, as well as malondialdehyde content. Accordingly, antagonistic toxicity was assessed between PFOA and SD. Furthermore, metabolomics revealed that V. natans improved stress tolerance through changes in enoic acid, palmitic acid, and palmitoleoyloxymyristic acid related to the fatty acid metabolism pathway responding to the coexisting pollutants. Additionally, PFOA and SD in combination induced more effects on the microbial community of biofilm. The alternation of α- and β-D-glucopyranose polysaccharides and the increased content of autoinducer peptides and N-acylated homoserine lactones indicated that PFOA and SD changed the structure and function of biofilm. These investigations provide a broader perspective and comprehensive analysis of the responses of aquatic plants and periphyton biofilms to PFAS and antibiotics in the environment.

Mass flow of per- and polyfluoroalkyl substances (PFAS) in a Swedish municipal wastewater network and wastewater treatment plant

PER: and polyfluoroalkyl substances (PFAS) are ubiquitously distributed in wastewater, due to their numerous uses in industry and consumer products, but little is known of PFAS mass flows in municipal wastewater network systems and within wastewater treatment plants (WWTPs). This study assessed mass flows of 26 PFAS in a wastewater network and WWTP, to provide new insights into their sources, transport, and fate in different treatment steps. Wastewater and sludge samples were collected from pumping stations and the main WWTP in Uppsala, Sweden. PFAS composition profiles and mass flows were used to identify sources within the sewage network. Wastewater from one pumping station showed elevated concentrations of C₃-C₈ PFCA, likely caused by an industrial source, and two stations had elevated concentrations of 6:2 FTSA, probably originating from a nearby firefighter training facility. Within the WWTP, short-chain PFAS dominated in wastewater, whereas long-chain PFAS dominated in sludge. The ratio of perfluoroalkyl sulfonates (PFSA) and ethylperfluorooctanesulfonamidoacetic acid (EtFOSAA) to ∑₂₆PFAS decreased during the WWTP process, likely due to sorption to sludge, but also transformation (EtFOSAA). Overall, PFAS were not efficiently removed in the WWTP, with mean removal efficiency of 10 ± 68% for individual PFAS, resulting in discharge of 7000 mg d^-1 ∑₂₆PFAS into the recipient. This shows that conventional WWTPs are inefficient in removing PFAS from wastewater and sludge, so advanced treatment techniques are needed.

Fractionation of perfluoroalkyl acids (PFAAs) along the aquatic food chain promoted by competitive effects between longer and shorter chain PFAAs

Perfluoroalkyl acids (PFAAs) are proteinophilic pollutants. We hypothesized that fractionation of PFAAs may occur along a food chain. To testify this hypothesis, we investigated the bioconcentration, bioaccumulation, and fractionation of 11 kinds of PFAAs (C-F = 3-11) along an aquatic food chain consisting of D. magna, zebrafish, and cichlid. The results showed that the proportions of PFNA, PFOA, and all shorter chain PFAAs in the D. magna and fish tissues were lower than the ones in exposure water, opposing to the other longer chain PFAAs. Predation promoted such fractionation differences, and the proportions of PFNA, PFOA, and all shorter chain PFAAs in organisms decreased while those of the other longer chain PFAAs increased along the food chain. The results of isothermal titration calorimetry and molecular docking experiments showed that binding affinities of PFAAs and fish proteins increased with the number of perfluorinated carbons, resulting in a substitution of shorter chain PFAAs by their longer chain analogues. It also triggered the differences in the uptake and elimination of PFFAs and competitive bioaccumulation between longer and shorter chain PFAAs. This study suggests that fractionation should be considered in studying environmental behaviors and evaluating ecological risks of multiple PFAAs.

Transport and transformation of perfluoroalkyl acids, isomer profiles, novel alternatives and unknown precursors from factories to dinner plates in China: New insights into crop bioaccumulation prediction and risk assessment

Perfluoroalkyl acids (PFAAs) are contaminants of global concern, and the inadvertent consumption of PFAA-contaminated crops may pose a threat to public health. Therefore, systematically studying their source tracing, bioaccumulation prediction and risk assessments in crops is an urgent priority. This study investigated the source apportionment and transport of PFAAs and novel fluorinated alternatives (collectively as per- and polyfluoroalkyl substances, PFASs) from factories to agricultural fields in a fluorochemical industrial region of China. Furthermore, bioaccumulation specificities and prediction of these chemicals in different vegetables were explored, followed by a comprehensive risk assessment from agricultural fields to dinner plates which considered precursor degradation. A positive matrix factorization model revealed that approximately 70 % of PFASs in agricultural soils were derived from fluorochemical manufacturing and metal processing. Alarming levels of ∑PFASs ranged 8.28-84.3 ng/g in soils and 163-7176 ng/g in vegetables. PFAS with short carbon chain or carboxylic acid group as well as branched isomers exhibited higher environmental transport potentials and bioaccumulation factors (BAFs) across a range of vegetables. The BAFs of different isomers of perfluorooctanoic acid (PFOA) decreased as the perfluoromethyl group moved further from the acid functional group. Hexafluoropropylene oxide dimer acid (GenX) showed relatively low BAFs, probably related to its ether bond with a high affinity to soil. Vegetables with fewer Casparian strips (e.g., carrot and radish), or more protein, possessed larger BAFs of PFASs. A bioaccumulation equation integrating critical parameters of PFASs, vegetables and soils, was built and corroborated with a good contamination prediction. After a total oxidizable precursors (TOP) assay, incremental perfluoroalkyl carboxylic acids (PFCAs) were massively found (325-5940 ng/g) in edible vegetable parts. Besides, precursor degradation and volatilization loss of PFASs was firstly confirmed during vegetable cooking. A risk assessment based on the TOP assay was developed to assist the protection of vegetable consumers.

Selective cationic covalent organic framework for high throughput rapid extraction of novel polyfluoroalkyl substances

Novel per- and polyfluoroalkyl substances (PFASs) raise global concerns due to their toxic effects on environment and human health. However, researches on analytical methods of novel PFASs are lacking. Here, a kind of selective cationic covalent organic framework (iCOF) was designed and loaded on the surface of cotton as an adsorbent. Then, a simple solid-phase extraction (SPE) method based on the cotton@iCOF was developed for high throughput rapid extraction of six novel PFASs in water samples, coupled with ultrahigh-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS) determination. Several important SPE parameters, such as the amount of iCOF, sample pH, desorption conditions and salinity were systematically investigated. Under optimal conditions, the limits of detection and quantification of this SPE-UHPLC-MS/MS method were as low as 0.08-2.14 ng/L and 0.28-7.15 ng/L, respectively. The recoveries were 77.9-117.6 % for the tap water and surface water, and F-53 B in surface water were detected. Notably, this SPE process was rapid (1 h for 500 mL water sample) compared with commercial SPE (normal 2-3 h), owing to little resistance of cotton@iCOF and omission of nitrogen blowing process, and high throughput with 12 samples concurrently extracted. Additionally, various characterization means and density functional theory (DFT) calculations showed that ion-exchange effect, hydrophobic interaction, hydrogen bonding and ordered channel structure synergistically contributed to the PFASs adsorption on cotton@iCOF. The cotton@iCOF-based SPE method with simplicity, rapidity, selectivity and efficiency provided new research ideas for the analysis and control of ionic emerging pollutants in water.

Uptake, distribution, and depuration of emerging per- and polyfluoroalkyl substances in mice: Role of gut microbiota

The bioaccumulation and fate in mammals of hexafluoropropylene oxide trimer acid (HFPO-TA) and hexafluoropropylene oxide dimer acid (HFPO-DA), as major alternatives for perfluorooctanoate (PFOA), have rarely been reported. In addition, the role of gut microbiota was greatly understudied. In this study, the uptake, distribution, and depuration of HFPO-TA, HFPO-DA, and PFOA were investigated by exposure to mice for 14 days, followed by a clearance period of 7 days. The patterns of tissue distribution and depuration kinetics of HFPO-TA and PFOA were similar, but different from HFPO-DA. Liver was the main deposition organ for HFPO-TA and PFOA, making contributions of 58.8 % and 59.1 % to the total mass recovered on day 14. Depuration of HFPO-DA was more rapid than HFPO-TA and PFOA. Approximately 95.3 % of HFPO-DA in liver was eliminated on day 21 compared with day 14. While the clearance rates of HPFO-TA and PFOA were only 6.1 % and 13.9 % on day 21. The comparison between normal and pseudo germ-free mice (GM) was also conducted to investigate the effect of gut microbial on in vivo absorption of the three per- and polyfluoroalkyl substances (PFASs). Significantly higher (p < 0.05) concentrations of all the three PFASs were observed in most organs and tissues of GM compared with NC group. An analysis of gut microbiota showed that the higher absorption of PFASs in GM group may be attributed to the increase of intestinal permeability (as indicated by the decrease of tight junction protein expression), which were induced by the change of lachnospiraceae abundance. The result highlighted the importance of gut microbiota in absorption and health risk evaluation of emerging PFASs.

First Evidence of Prenatal Exposure to Emerging Poly- and Perfluoroalkyl Substances Associated with E-Waste Dismantling: Chemical Structure-Based Placental Transfer and Health Risks

Limited information is available about prenatal exposure to per- and polyfluoroalkyl substances (PFAS) in electronic waste (e-waste) recycling sites. In this study, we determined 21 emerging PFAS and 13 legacy PFAS in 94 paired maternal and cord serum samples collected from an e-waste dismantling site in Southern China. We found 6:2 fluorotelomer sulfonate (6:2 FTSA), 6:2 chlorinated polyfluorinated ether sulfonate (6:2 Cl-PFESA), and perfluorooctanephosphonate (PFOPA) as the major emerging PFAS, regardless of matrices, at median concentrations of 2.40, 1.78, and 0.69 ng/mL, respectively, in maternal serum samples, and 2.30, 0.73, and 0.72 ng/mL, respectively, in cord serum samples. Our results provide evidence that e-waste dismantling activities contribute to human exposure to 6:2 FTSA, 6:2 Cl-PFESA, and PFOPA. The trans-placental transfer efficiencies of emerging PFAS (0.42-0.94) were higher than that of perfluorooctanesulfonic acid (0.37) and were structure-dependent. The substitution of fluorine with chlorine or hydrogen and/or hydrophilic functional groups may alter trans-placental transfer efficiencies. Multiple linear regression analysis indicated significant associations between maternal serum concentrations of emerging PFAS and maternal clinical parameters, especially liver function and erythrocyte-related biomarkers. This study provides new insights into prenatal exposure to multiple PFAS in e-waste dismantling areas and the prevalence of emerging PFAS in people living near the sites.

Removal of Per-, Poly-fluoroalkyl substances (PFASs) and multi-biosphere community dynamics in a bacteria-algae symbiotic aquatic ecosystem

The presence of Per-, Poly-fluoroalkyl substances (PFASs) in aquatic ecosystems has drawn broad concerns in the scientific community due to their biological toxicity. However, little has been explored regarding PFASs' removal in phytoplankton-dominated environments. This study aimed to create a simulated bacteria-algae symbiotic ecosystem to observe the potential transportation of PFASs. Mass distributions showed that sand (63-2000 μm), silt & clay (0-63 μm), the phycosphere (>3 μm plankton), and the free-living biosphere (0.22-3 μm plankton) contained 19.00, 7.78, 5.73 and 2.75% PFASs in their total mass, respectively. Significant correlations were observed between carbon chain lengths and removal rates (R² = 0.822, p < 10^-4). Structural equation models revealed potential PFAS transportation pathways, such as water-phycosphere- free-living biosphere-sand-silt&clay, and water-sand-silt&clay (p < 0.05). The presence of PFASs decreased the bacterial density but increased algal density (p < 0.01) in the planktonic environment, and PFASs with longer carbon chain lengths showed a stronger enhancement in microbial community successions (p < 0.05). In algal metabolisms, chlorophyll-a and carotenoids were the key pigments that resisted reactive oxygen species caused by PFASs. PFBA (perfluorobutyric acid) (10.38-14.68%) and PFTeDA (perfluorotetradecanoic acid) (10.33-15.96%) affected bacterial metabolisms in phycosphere the most, while in the free-living biosphere was most effected by PFPeA (perfluorovaleric acid) (13.21-13.99%) and PFDoA (perfluorododecanoic acid) (10.04-10.50%). The results of this study provide new guidance measures for PFAS removal and management in aquatic environments.

Occurrence, fate and risk assessment of per- and polyfluoroalkyl substances in wastewater treatment plants in Shaanxi, China

Wastewater treatment plants (WWTPs) are considered as major sinks for per- and polyfluoroalkyl substances (PFASs). However, conventional WWTPs with low efficiency are also a secondary point source of PFASs entering the environment. Herein, a large-scale investigation of PFASs was conducted in 44 WWTPs throughout Shaanxi Province in the transitional zone between North and South China. The composition profiles of target PFASs differed between wastewater and sludge samples. Perfluorobutanoic acid was dominant in wastewater influent and effluent samples, with maximum concentrations of 59.8 and 11.4 ng/L, respectively. Perfluorooctane sulfonic acid occurred predominantly in sludge samples, with a maximum concentration of 73.2 ng/g. Through wastewater treatment, short-chain PFASs with an even number of carbon atoms were mostly removed, whereas short-chain PFASs with an odd number of carbon atoms were primarily discharged into receiving water. Long-chain PFASs (perfluoroalkyl carboxylic acids: C ≥ 8; perfluoroalkane sulfonic acids: C ≥ 6) were not removed efficiently and secondary production might occur during treatment. Based on the risk quotient, PFASs residues in wastewater effluent posed minimal ecological risk, but the residues in sludge posed low to high potential risk. The mass loadings of PFASs discharged through wastewater and sludge were 15.5 and 3.74 kg/year, respectively, from all WWTPs in Shaanxi Province.

Chemical fingerprinting of organic micropollutants in different industrial treated wastewater effluents and their effluent-receiving river

Industry wastewater is considered one of the worst polluters of our precious water ecologies. However, the types of pollutants present in wastewater from industrial wastewater treatment plants (IWTPs) are still unclear. In this study, a simple and effective chemical fingerprinting method for checking the source-sink relationships among different industrial wastewaters and their effluent-receiving river was established. 107, 228, 155, and 337 chemicals were screened out in wastewater from electronics, steel, textile, and printing and dyeing plants, respectively. Chemical fingerprinting of the detected chemicals was performed, and results showed that aromatic compounds were the most prevalent among the pollutant categories (i.e., 56, 189, and 168 in electronics, iron and steel, and printing and dyeing plants, respectively). The traceability analysis of the chemicals selected in the effluent determined the characteristic pollutants of different industrial enterprises. Sixty-eight compounds were identified as the characteristic pollutants in the different process stages of wastewater of the four IWTPs. Of the 84 effluent-receiving river water signature pollutants, 47.6% (n = 40) were also detected in the effluent from the four IWTPs. Effective screening of organic pollutants in industrial wastewater and determining their sources will help accelerate the improvement of industrial wastewater treatment technology.

Occurrence, source apportionment, and pollution assessment of per- and polyfluoroalkyl substances in a river across rural and urban areas

Forty-three novel and legacy per- and polyfluoroalkyl substances (PFASs) in water and sediments from the Chaobai River (Beijing) were quantified. The total PFASs concentrations varied from 0.04 to 31.3 ng/L in water with significant spatial but insignificant seasonal variations, and changed from 0.03 to 4.29 ng/g in sediment with insignificant spatial but significant seasonal variations. The PFASs concentrations in water from the upstream across the rural area reflected the background level due to the extremely low concentration and very few detected PFASs. The consumer products and metal plating/textile were the predominant pollution sources of PFASs in winter and summer, respectively, for both water and sediment samples. Integrating the determined baseline value, the distribution of PFASs concentrations, and the ecological risks of PFASs, three criteria were proposed, which divide the PFASs concentrations in water into four pollution levels, i.e., insignificant, low, medium, and high. According to the suggested criteria, 96.4% of the PFASs levels in upstream was insignificant pollution, which decreased to 50.4% in downstream and 50.8% in reservoirs. The PFASs in China's and world's surface waters demonstrated similar pollution patterns, with PFOA, PFOS, and PFHxA being the top 3 polluted PFASs. This study makes a small step forward the development of water quality standard for PFASs, which is of great importance for pollution control and risk management of PFASs.

Ecotoxicological responses and removal of submerged macrophyte Hydrilla verticillate to multiple perfluoroalkyl acid (PFAA) pollutants in aquatic environments

The ubiquitous existence of perfluoroalkyl acids (PFAAs) in aquatic environments might pose toxic potential to ecosystems. To assess the ecotoxicological responses and removal of submerged macrophyte to multiple PFAA pollutants in aquatic environments, a typical submerged macrophyte, Hydrilla verticillate, was exposed to solutions with 12 typical PFAAs in the present study. The results showed that PFAAs at concentrations higher than 10 μg/L had significantly passive effects on biomass, relative growth rates, chlorophyll contents, and chlorophyll autofluorescence. PFAAs could induce the accumulation of hydrogen peroxide and lipid peroxidation in H. verticillate. Significant upregulation of CAT was observed in treatments with more than 10 μg/L PFAAs (p < 0.05). The results also showed that 13.53-20.01% and 19.73-37.72% of PFAAs could be removed in treatments without plants and with H. verticillate, respectively. The removal rates of PFAAs were significantly correlated with perfluoroalkyl chain length in treatments with H. verticillate. The removal of PFAAs was suggested to be related to the uptake of plant tissues and biosorption of microbiota. Furthermore, the dominant microbiota and biomarkers were identified in water and biofilm. Betaproteobacteriales was the most dominant microbiota at the order level. The presence of PFAAs could significantly increase the relative abundance of Micrococcales, Verrucomicrobiales, Rhizobiales, Sphingomonadales, Roseomonas, Cyanobium_PCC_6307, and Synechococcales. Our results provide scientific basis for evaluating the ecotoxicological responses and removal of submerged macrophytes in response to multiple PFAA pollutants at environmentally relevant levels, thereby providing insights into PFAA management and removal.

Interactions between dissolved organic matter and perfluoroalkyl acids in natural rivers and lakes: A case study of the northwest of Taihu Lake Basin, China

Understanding the interactions between dissolved organic matter (DOM) and perfluoroalkyl acids (PFAAs) is essential for predicting the distribution, transport, and fate of PFAAs in aquatic environments. Based on field investigations in the northwest of Taihu Lake Basin combined with laboratory experiments, we obtained DOM and PFAA concentrations as well as compositions and investigated key factors of DOM affecting PFAA variability and capture of PFAAs by DOM. Results indicated that the total concentrations of PFAAs were 73.4-689 ng/L in surface water and that PFAAs were dominated by C3-7 perfluoroalkyl carboxylic acids and perfluorooctane sulfonic acid. The main components of DOM included tyrosine-, fulvic-, and tryptophan-like substances. The Mantel test revealed a significant positive correlation between DOM and PFAAs (P = 0.0001). Fulvic-like substances were identified as the most crucial factors affecting PFAA variability. The laboratory experiments revealed that DOM can spontaneously aggregate into a microgel. Furthermore, 19.1-50.9% of PFAAs, DOM characteristic peaks, and several metals (Ca, Mg, Cu, and Fe) can be removed during aggregation, indicating the capacity of DOM binding organic/inorganic substances. The fulvic-like substances were more effectively removed than the protein-like substances. The distribution coefficients of all PFAAs except perfluorohexanoic acid significantly correlated with their perfluorinated carbon numbers (r = 0.975, p<0.001). Our results provided insights into the interactions between DOM and PFAAs, improving the understanding of the distribution, transport, and fate of PFAAs in aquatic environments.

Per-, poly-fluoroalkyl substances (PFASs) and planktonic microbiomes: Identification of biotic and abiotic regulations in community coalescence and food webs

The importance of per-, poly-fluoroalkyl substances (PFASs) effects on riverine microbiomes is receiving increased recognition in the environmental sciences. However, few studies have explored how PFASs affect microbiomes across trophic levels, specifically through predator-prey interactions. This study examined the community profiles of planktonic archaea, bacteria, fungi, algae, protozoa, and metazoa in a semi-industrial and agricultural river alongside their interactions with 15 detected PFASs. As abiotic factors, PFASs affected community coalescence more than biogenic substances (p < 0.05). For biotic regulations, sub-communities in rare biospheres (including always rare taxa-ART and critically rare taxa-CRT) contributed to spatial community coalescence more than sub-communities in abundant biospheres (always abundant taxa-AAT and critically abundant taxa-CAT) (p < 0.05). Metazoa-bacteria (Modularity = 1.971) and protozoa-fungi (1.723) were determined to be the most stable predator-prey networks. Based on pathway models, short-chain PFBA (C4) was shown to weaken the trophic transfer efficiencies from heterotrophic bacteria (HB) to heterotrophic flagellates (HF) (p < 0.05). Long-chain PFTeDA (C14) promoted HB to amoeba (p < 0.05), which we postulate is the pathway for PFTeDA to enter the microbial food chain. Our preliminary results elucidated the influence of PFASs on planktonic microbial food webs and highlighted the need to consider protecting and remediating riverine ecosystems containing PFASs.

Legacy and Emerging Per- and Polyfluoroalkyl Substances Behave Distinctly in Spatial Distribution and Multimedia Partitioning: A Case Study in the Pearl River, China

Per- and polyfluoroalkyl substances (PFASs) have attracted worldwide attention due to their ubiquitous occurrence, bioaccumulation, and toxicological effects, yet the fate of PFASs in a lotic ecosystem is largely unknown. To elucidate spatial distribution and multimedia partitioning of legacy and emerging PFASs in a lotic river flowing into an estuary, PFASs were synchronously analyzed in water, suspended particulate matter (SPM), sediment, and biota samples collected along Guangzhou reach of the Pearl River, South China. Geographically, the concentrations of PFASs in the water phase showed a decreasing trend from the upper and middle sections (urban area) to the down section (suburban area close to estuary) of the river. While perfluorooctanoic acid predominated in water and SPM, more diverse compositions were observed in sediment and biota with the increase in contributions of long-chain PFASs. Field-derived sediment-water partitioning coefficients (K_d) and bioaccumulation factors (BAFs) of PFASs increased with the increase in perfluorinated carbons. Besides hydrophobicity, water pH and salinity significantly affected the multimedia partitioning of PFASs in a lotic ecosystem. In addition, 87 homologues (63 classes) were identified as emerging PFASs in four media using suspect analysis. Interestingly, K_d and BAF of the emerging PFASs were often higher than legacy PFASs containing the same perfluorinated carbons, raising a special concern on the environmental risk of emerging PFASs.

Removal potential of multiple perfluoroalkyl acids (PFAAs) by submerged macrophytes in aquatic environments: Tolerance of Vallisneria natans and PFAA removal in submerged macrophyte-microbiota systems

Perfluoroalkyl acids (PFAAs) have emerged as a global concern in aquatic environment remediation due to their abundance, persistence, bioaccumulation, and toxicity. To comprehensively understand the removal potential of multiple PFAAs by submerged macrophytes in aquatic environments, systematic investigations into the tolerance of the typical submerged macrophyte Vallisneria natans to 12 typical PFAAs and the removal capacity to PFAAs in V. natans-microbiota systems were carried out. Results showed that although PFAAs could induce the accumulation of hydrogen peroxide and malondialdehyde, V. natans was overall resistant to multiple PFAAs with natural concentrations. Catalase is one of the main strategies of V. natans to alleviate PFAA stress. Microbiota can remove 18.10-30.84% of the PFAAs from the water column. 24.35-73.45% of PFAAs were removed from water in V. natans-microbiota systems. The uptake of plant tissues and the bioaccumulation of microbiota were proposed as the main removal processes. The removal rates were significantly correlated with the perfluorinated carbon atoms numbers (p < 0.05). PFAAs and V. natans increased the relative abundance of Betaproteobacteria, Nostocales, Microscillaceae, Sphingobacteriales, SBR1031, Chlamydiales, Phycisphaerae, Caldilineales, Rhodobacterales, and Verrucomicrobiales. The present study suggested that V. natans can be a potential species to remove multiple PFAAs in aquatic environments, and further providing insights into the PFAAs' remediation.

Source apportionment and crop bioaccumulation of perfluoroalkyl acids and novel alternatives in an industrial-intensive region with fluorochemical production, China: Health implications for human exposure

Due to their great environmental hazards, the widely used legacy perfluoroalkyl acids (PFAAs) are gradually restricted, and novel alternatives are being developed and applied. For efficient control of emerging environmental risks in agricultural production, we systematically studied the source apportionment in field soils and bioaccumulation characteristics in multiple crops of 12 PFAAs and five novel alternatives in an industrial-intensive region of China, followed by human exposure estimation and health risk assessment. Compared with perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), shorter-chained PFAAs and novel alternatives have become the dominant components in local soils and crops, indicating their wide application. A positive matrix factorization (PMF) model coupled with multivariate analysis identified fluoropolymer manufacturing and textile treatment as the principal sources. The bioaccumulation factors (BAFs) of individual PFAAs and alternatives in crops decreased with increasing carbon chain lengths. As a novel alternative of PFOA, hexafluoropropylene oxide dimer acid (GenX) exhibited much higher BAFs; for the alternative of PFOS, 6:2 chlorinated polyfluorinated ether sulfonic acid (6:2 Cl-PFESA) showed lower BAFs. The bioaccumulation capacities of PFAAs and alternatives were also associated with soil organic matter and crop species. Through crop consumption, short-chained PFAAs and novel alternatives might pose emerging human health threats.

Poly- and Perfluorinated Alkyl Substances in Air and Water from Dhaka, Bangladesh

Bangladesh hosts extensive textile manufacturing, for some of which per- and polyfluorinated alkyl substances (PFAS) have been used to impart water and dirt repellency, among other things. Textile waste emissions to the atmosphere and discharge into rivers and other bodies of water could present a significant concern for human and ecosystem health, but there is little information on PFAS in Bangladesh. To assess the presence of ionic PFAS and their precursors in air and water from Dhaka, Bangladesh, polyethylene sheets were deployed for 28 days as passive samplers for neutral PFAS in outdoor air and water, while ionic PFAS were measured from discrete water grabs. Fluorotelomer alcohols (FTOHs) were detected at almost all sites in air and water; the most frequently detected compound was 6:2 FTOH, ranging from below instrumental detection limits (<IDL) to 70 ng m^-3 in air and from <IDL to -19 ng L^-1 in water. Of the ionic PFAS, perfluorobutanoic acid (PFBA), perfluorohexanoic acid, perfluorooctanoic acid, perfluorohexane sulfonic acid, and perfluorooctane sulfonic acid dominated in frequency of detection and magnitude, with concentrations ranging from 1.8 to 19.0 ng L^-1 in surface waters. The prevalence of 6:2 FTOH and PFBA across sites probably reflects their use in textile manufacturing and could indicate the industry's switch to shorter-chain PFAS alternatives. Environ Toxicol Chem 2022;41:334-342. © 2021 SETAC.

Occurrence and removal of poly/perfluoroalkyl substances (PFAS) in municipal and industrial wastewater treatment plants

The presence of poly- and perfluoroalkyl substances (PFAS) has caused serious problems for drinking water supplies especially at intake locations close to PFAS manufacturing facilities, wastewater treatment plants (WWTPs), and sites where PFAS-containing firefighting foam was regularly used. Although monitoring is increasing, knowledge on PFAS occurrences particularly in municipal and industrial effluents is still relatively low. Even though the production of C8-based PFAS has been phased out, they are still being detected at many WWTPs. Emerging PFAS such as GenX and F-53B are also beginning to be reported in aquatic environments. This paper presents a broad review and discussion on the occurrence of PFAS in municipal and industrial wastewater which appear to be their main sources. Carbon adsorption and ion exchange are currently used treatment technologies for PFAS removal. However, these methods have been reported to be ineffective for the removal of short-chain PFAS. Several pioneering treatment technologies, such as electrooxidation, ultrasound, and plasma have been reported for PFAS degradation. Nevertheless, in-depth research should be performed for the applicability of emerging technologies for real-world applications. This paper examines different technologies and helps to understand the research needs to improve the development of treatment processes for PFAS in wastewater streams.

A review of the occurrence, transformation, and removal of poly- and perfluoroalkyl substances (PFAS) in wastewater treatment plants

Poly- and perfluoroalkyl substances (PFAS) comprise more than 4,000 anthropogenically manufactured compounds with widescale consumer and industrial applications. This critical review compiles the latest information on the worldwide distribution of PFAS and evaluates their fate in wastewater treatment plants (WWTPs). A large proportion (>30%) of monitoring studies in WWTPs were conducted in China, followed by Europe (30%) and North America (16%), whereas information is generally lacking for other parts of the world, including most of the developing countries. Short and long-chain perfluoroalkyl acids (PFAAs) were widely detected in both the influents (up to 1,000 ng/L) and effluents (15 to >1,500 ng/L) of WWTPs. To date, limited data is available regarding levels of PFAS precursors and ultra-short chain PFAS in WWTPs. Most WWTPs exhibited low removal efficiencies for PFAS, and many studies reported an increase in the levels of PFAAs after wastewater treatment. The analysis of the fate of various classes of PFAS at different wastewater treatment stages (aerobic and/aerobic biodegradation, photodegradation, and chemical degradation) revealed biodegradation as the primary mechanism responsible for the transformation of PFAS precursors to PFAAs in WWTPs. Remediation studies at full scale and laboratory scale suggest advanced processes such as adsorption using ion exchange resins, electrochemical degradation, and nanofiltration are more effective in removing PFAS (~95-100%) than conventional processes. However, the applicability of such treatments for real-world WWTPs faces significant challenges due to the scaling-up requirements, mass-transfer limitations, and management of treatment by-products and wastes. Combining more than one technique for effective removal of PFAS, while addressing limitations of the individual treatments, could be beneficial. Considering environmental concentrations of PFAS, cost-effectiveness, and ease of operation, nanofiltration followed by adsorption using wood-derived biochar and/or activated carbons could be a viable option if introduced to conventional treatment systems. However, the large-scale applicability of the same needs to be further verified.