Simultaneous measurement of cellular respiration and acidification with a single CMOS ISFET

Modelling cancer metabolism in vitro: current improvements and future challenges

Advances in cancer biology over the past decades have revealed that metabolic adaptation of cancer cells is an essential aspect of tumorigenesis. However, recent insights into tumour metabolism in vivo have revealed dissimilarities with results obtained in vitro. This is partly due to the reductionism of in vitro cancer models that struggle to reproduce the complexity of tumour tissues. This review describes some of the discrepancies in cancer cell metabolism between in vitro and in vivo conditions, and presents current methodological approaches and tools used to bridge the gap with the clinically relevant microenvironment. As such, these approaches should generate new knowledge that could be more effectively translated into therapeutic opportunities.

Nanocomposite Hydrogels as Functional Extracellular Matrices

Over recent years, nano-engineered materials have become an important component of artificial extracellular matrices. On one hand, these materials enable static enhancement of the bulk properties of cell scaffolds, for instance, they can alter mechanical properties or electrical conductivity, in order to better mimic the in vivo cell environment. Yet, many nanomaterials also exhibit dynamic, remotely tunable optical, electrical, magnetic, or acoustic properties, and therefore, can be used to non-invasively deliver localized, dynamic stimuli to cells cultured in artificial ECMs in three dimensions. Vice versa, the same, functional nanomaterials, can also report changing environmental conditions-whether or not, as a result of a dynamically applied stimulus-and as such provide means for wireless, long-term monitoring of the cell status inside the culture. In this review article, we present an overview of the technological advances regarding the incorporation of functional nanomaterials in artificial extracellular matrices, highlighting both passive and dynamically tunable nano-engineered components.

Biosensors to Monitor Cell Activity in 3D Hydrogel-Based Tissue Models

Three-dimensional (3D) culture models have gained relevant interest in tissue engineering and drug discovery owing to their suitability to reproduce in vitro some key aspects of human tissues and to provide predictive information for in vivo tests. In this context, the use of hydrogels as artificial extracellular matrices is of paramount relevance, since they allow closer recapitulation of (patho)physiological features of human tissues. However, most of the analyses aimed at characterizing these models are based on time-consuming and endpoint assays, which can provide only static and limited data on cellular behavior. On the other hand, biosensing systems could be adopted to measure on-line cellular activity, as currently performed in bi-dimensional, i.e., monolayer, cell culture systems; however, their translation and integration within 3D hydrogel-based systems is not straight forward, due to the geometry and materials properties of these advanced cell culturing approaches. Therefore, researchers have adopted different strategies, through the development of biochemical, electrochemical and optical sensors, but challenges still remain in employing these devices. In this review, after examining recent advances in adapting existing biosensors from traditional cell monolayers to polymeric 3D cells cultures, we will focus on novel designs and outcomes of a range of biosensors specifically developed to provide real-time analysis of hydrogel-based cultures.

Chemically Induced pH Perturbations for Analyzing Biological Barriers Using Ion-Sensitive Field-Effect Transistors

Potentiometric pH measurements have long been used for the bioanalysis of biofluids, tissues, and cells. A glass pH electrode and ion-sensitive field-effect transistor (ISFET) can measure the time course of pH changes in a microenvironment as a result of physiological and biological activities. However, the signal interpretation of passive pH sensing is difficult because many biological activities influence the spatiotemporal distribution of pH in the microenvironment. Moreover, time course measurement suffers from stability because of gradual drifts in signaling. To address these issues, an active method of pH sensing was developed for the analysis of the cell barrier in vitro. The microenvironmental pH is temporarily perturbed by introducing a low concentration of weak acid (NH₄⁺) or base (CH₃COO⁻) to cells cultured on the gate insulator of ISFET using a superfusion system. Considering the pH perturbation originates from the semi-permeability of lipid bilayer plasma membranes, induced proton dynamics are used for analyzing the biomembrane barriers against ions and hydrated species following interaction with exogenous reagents. The unique feature of the method is the sensitivity to the formation of transmembrane pores as small as a proton (H⁺), enabling the analysis of cell–nanomaterial interactions at the molecular level. The new modality of cell analysis using ISFET is expected to be applied to nanomedicine, drug screening, and tissue engineering.

An Optical and Temperature Assisted CMOS ISFET Sensor Array for Robust E. Coli Detection

Both bacterial viability and concentration are significant metrics for bacterial detection. Existing miniaturized and cost-effective single-mode sensor, pH or optical, can only be skilled at detecting single information viability or concentration. This paper presents an inverter-based CMOS ion-sensitive-field-effect-transistor (ISFET) sensor array, featuring bacterial pH detection which is an indicator of viability. The proposed design realizes pH detection using the native passivation layer of CMOS process as a sensing layer and configuring an inverter-based front-end as a capacitive feedback amplifier. This sensor array is assisted by temperature sensing and optical detection which reveals bacterial concentration. The optical detection is enabled using the leakage current of a reset switch as a response to a light source. While in reset mode, the inverter-based amplifier works as a temperature sensor that could help to reduce temperature influences on pH and optical detection. All the functionalities are realized using one single inverter-based amplifier, resulting in a compact pixel structure and largely relaxed design complexity for the sensor system. Fabricated in 0.18 μm standard CMOS process, the proposed CMOS sensor array system achieves an amplified pH sensitivity of 221 mV/pH, an improved sensor resolution of 0.03 pH through systematic noise optimization, a linear optical response, and a maximum temperature error of 0.69 ^°C. The sensing capabilities of the proposed design are demonstrated through on-chip Escherichia coli (E. coli) detection. This study may be extended to a rapid and cost-effective platform that renders multiple information of bacterial samples.

Monitoring Contractile Cardiomyocytes via Impedance Using Multipurpose Thin Film Ruthenium Oxide Electrodes

A ruthenium oxide (RuOx) electrode was used to monitor contractile events of human pluripotent stem cells-derived cardiomyocytes (hPSC-CMs) through electrical impedance spectroscopy (EIS). Using RuOx electrodes presents an advantage over standard thin film Pt electrodes because the RuOx electrodes can also be used as electrochemical sensor for pH, O₂, and nitric oxide, providing multisensory functionality with the same electrode. First, the EIS signal was validated in an optically transparent well-plate setup using Pt wire electrodes. This way, visual data could be recorded simultaneously. Frequency analyses of both EIS and the visual data revealed almost identical frequency components. This suggests both the EIS and visual data captured the similar events of the beating of (an area of) hPSC-CMs. Similar EIS measurement was then performed using the RuOx electrode, which yielded comparable signal and periodicity. This mode of operation adds to the versatility of the RuOx electrode's use in in vitro studies.

Microfluidic Organoids-on-a-Chip: Quantum Leap in Cancer Research

Organ-like cell clusters, so-called organoids, which exhibit self-organized and similar organ functionality as the tissue of origin, have provided a whole new level of bioinspiration for ex vivo systems. Microfluidic organoid or organs-on-a-chip platforms are a new group of micro-engineered promising models that recapitulate 3D tissue structure and physiology and combines several advantages of current in vivo and in vitro models. Microfluidics technology is used in numerous applications since it allows us to control and manipulate fluid flows with a high degree of accuracy. This system is an emerging tool for understanding disease development and progression, especially for personalized therapeutic strategies for cancer treatment, which provide well-grounded, cost-effective, powerful, fast, and reproducible results. In this review, we highlight how the organoid-on-a-chip models have improved the potential of efficiency and reproducibility of organoid cultures. More widely, we discuss current challenges and development on organoid culture systems together with microfluidic approaches and their limitations. Finally, we describe the recent progress and potential utilization in the organs-on-a-chip practice.

Measuring Both pH and O2 with a Single On-Chip Sensor in Cultures of Human Pluripotent Stem Cell-Derived Cardiomyocytes to Track Induced Changes in Cellular Metabolism

In vitro studies which focus on cellular metabolism can benefit from time-resolved readouts from the living cells. pH and O₂ concentration are fundamental parameters upon which cellular metabolism is often inferred. This work demonstrates a novel use of a ruthenium oxide (RuO_x) electrode for in vitro studies. The RuO_x electrode was characterized to measure both pH and O₂ using two different modes. When operated potentiometrically, continuous pH reading can be obtained, and O₂ concentration can be measured chronoamperometrically. In this work, we demonstrate the use of the RuO_x electrodes in inferring two different types of metabolism of human pluripotent stem cell-derived cardiomyocytes. We also show and discuss the interpretation of the measurements into meaningful extracellular acidification rates and oxygen consumption rates of the cells. Overall, we present the RuO_x electrode as a versatile and powerful tool in in vitro cell metabolism studies, especially in comparative settings.

Microsensor systems for cell metabolism - from 2D culture to organ-on-chip

Microsensor systems for cell metabolism are essential tools for investigation and standardization in cell culture. Electrochemical and optical read-out schemes dominate, which enable the marker-free, continuous, online recording of transient effects and deliver information beyond microscopy and end-point tests. There has been much progress in microfluidics and microsensors, but the translation of both into standard cell culture procedures is still limited. Within this critical review, we discuss different cell culture formats ranging from standard culture vessels to dedicated microfluidic platforms. Key aspects are the appropriate supply of cells, mass transport of metabolites to the sensors and generation of stimuli. Microfluidics enable the transition from static to dynamic conditions in culture and measurement. We illustrate the parameters oxygen (respiration), pH (acidification), glucose and lactate (energy metabolism) as well as short-lived reactive species (ROS/RNS) from the perspective of microsensor integration in 2D and 3D cell culture. We discuss different sensor principles and types, along with their limitations, microfabrication technologies and materials. The state-of-the-art of microsensor platforms for cell culture is discussed with respect to sensor performance, the number of parameters and timescale of application. That includes the advances from 2D culture to the increasingly important 3D approaches, with specific requirements for organotypic microtissues, spheroids and solid matrix cultures. We conclude on the current progress, potential, benefits and limitations of cell culture monitoring systems from monolayer culture to organ-on-chip systems.

Sensor Access to the Cellular Microenvironment Using the Sensing Cell Culture Flask

The Sensing Cell Culture Flask (SCCF) is a cell culture monitoring system accessing the cellular microenvironment in 2D cell culture using electrochemical microsensors. The system is based on microfabricated sensor chips embedded in standard cell culture flasks. Ideally, the sensor chips could be equipped with any electrochemical sensor. Its transparency allows optical inspection of the cells during measurement. The surface of the sensor chip is in-plane with the flask surface allowing undisturbed cell growth on the sensor chip. A custom developed rack system allows easy usage of multiple flasks in parallel within an incubator. The presented data demonstrates the application of the SCCF with brain tumor (T98G) and breast cancer (T-47D) cells. Amperometric oxygen sensors were used to monitor cellular respiration with different incubation conditions. Cellular acidification was accessed with potentiometric pH sensors using electrodeposited iridium oxide films. The system itself provides the foundation for electrochemical monitoring systems in 3D cell culture.

Sensing Cellular Metabolic Activity via a Molecular-Controlled Semiconductor Resistor

Over the last decade, we have developed a molecular-controlled semiconductor resistor (MOCSER) device that is highly sensitive to variations in its surface potentials. This device was applied as a molecular sensor both in the gas phase and in solutions. The device is based on an AlGaAs/GaAs structure. In the current work, we developed an electronic biosensor for real-time, label-free monitoring of cellular metabolic activity by culturing HeLa cells directly on top of the device's conductive channel. Several properties of GaAs make it attractive for developing biosensors, among others its high electron mobility and ability to control the device's properties by proper epitaxial growing. However, GaAs is very reactive and sensitive to oxidation in aqueous solutions, and its arsenic residues are highly toxic. Nevertheless, we have managed to overcome this inherent chemical instability by developing a surface-protecting layer using polymerized (3-mercaptopropyl)-trimethoxysilane (MPTMS). To improve cell adhesion and biocompatibility, the MPTMS-coated devices were further modified with an additional layer of (3-aminopropyl)-trimethoxysilane (APTMS). HeLa cells were found to grow successfully on these devices, and MOCSER devices cultured with these cells were stable and sensitive to cellular metabolic activity. The sensitivity of the MOCSER device results from the sensing of extracellular acidification in the microenvironment of the cell-MOCSER interspace. We have found that this sensitivity is maintained only when the device is partially covered with the cellular layer, whereas at full coverage the sensitivity is lost. This phenomenon is related to the negatively charged cellular membrane potentials that lead to a reduction in the channel's conductivity. We propose that the coated MOCSER device can be applied for real-time and continuous monitoring of cellular viability and activity.

Proton-sensing transistor systems for detecting ion leakage from plasma membranes under chemical stimuli

The membrane integrity of live cells is routinely evaluated for cytotoxicity induced by chemical or physical stimuli. Recent progress in bioengineering means that high-quality toxicity validation is required. Here, we report a pH-sensitive transistor system developed for the continuous monitoring of ion leakage from cell membranes upon challenge by toxic compounds. Temporal changes in pH were generated with high reproducibility via periodic flushing of HepG2 cells on a gate insulator of a proton-sensitive field-effect transistor with isotonic buffer solutions with/without NH₄Cl. The pH transients at the point of NH₄Cl addition/withdrawal originated from the free permeation of NH₃ across the semi-permeable plasma membranes, and the proton sponge effect produced by the ammonia equilibrium. Irreversible attenuation of the pH transient was observed when the cells were subjected to a membrane-toxic reagent. Experiments and simulations proved that the decrease in the pH transient was proportional to the area of the ion-permeable pores on the damaged plasma membranes. The pH signal was correlated with the degree of hemolysis produced by the model reagents. The pH assay was sensitive to the formation of molecularly sized pores that were otherwise not measurable via detection of the leakage of hemoglobin, because the hydrodynamic radius of hemoglobin was greater than 3.1nm in the hemolysis assay. The pH transient was not disturbed by inherent ion-transporter activity. The ISFET assay was applied to a wide variety of cell types. The system presented here is fast, sensitive, practical and scalable, and will be useful for validating cytotoxins and nanomaterials.

STATEMENT OF SIGNIFICANCE

The plasma membrane toxicity and hemolysis are widely and routinely evaluated in biomaterials science and biomedical engineering. Despite the recent development of a variety of methods/materials for efficient gene/drug delivery systems to the cytosol, the methodologies for safety validation remain unchanged in many years while leaving some major issues such as sensitivity, accuracy, and fast response. The paper describes a new way of measuring the plasma membrane leakage in real time upon challenge by toxic reagents using a solid-state transistor that is sensitive to proton as the smallest indicator. Our system was reliable and was correlated to the results from hemolysis assay with advanced features in sensitivity, fast response, and wide applicability to chemical species. The downsizing and integration features of semiconductor fabrication technologies may realize cytotoxicity assays at the single-cell level in multi-parallel.

Identification of types of membrane injuries and cell death using whole cell-based proton-sensitive field-effect transistor systems

Membrane injury and apoptosis of mammalian cells by chemical stimuli were distinguished using ammonia-perfused continuous pH-sensing systems.

Oleyl group-functionalized insulating gate transistors for measuring extracellular pH of floating cells

The extracellular ionic microenvironment has a close relationship to biological activities such as by cellular respiration, cancer development, and immune response. A system composed of ion-sensitive field-effect transistors (ISFET), cells, and program-controlled fluidics has enabled the acquisition of real-time information about the integrity of the cell membrane via pH measurement. Here we aimed to extend this system toward floating cells such as T lymphocytes for investigating complement activation and pharmacokinetics through alternations in the plasma membrane integrity. We functionalized the surface of tantalum oxide gate insulator of ISFET with oleyl-tethered phosphonic acid for interacting with the plasma membranes of floating cells without affecting the cell signaling. The surface modification was characterized by X-ray photoelectron spectroscopy and water contact angle measurements. The Nernst response of -37.8 mV/pH was obtained for the surface-modified ISFET at 37 °C. The oleyl group-functionalized gate insulator successfully captured Jurkat T cells in a fluidic condition without acute cytotoxicity. The system was able to record the time course of pH changes at the cells/ISFET interface during the process of instant addition and withdrawal of ammonium chloride. Further, the plasma membrane injury of floating cells after exposure by detergent Triton™ X-100 was successfully determined using the modified ISFET with enhanced sensitivity as compared with conventional hemolysis assays.

Design and Characterization of a Sensorized Microfluidic Cell-Culture System with Electro-Thermal Micro-Pumps and Sensors for Cell Adhesion, Oxygen, and pH on a Glass Chip

We combined a multi-sensor glass-chip with a microfluidic channel grid for the characterization of cellular behavior. The grid was imprinted in poly-dimethyl-siloxane. Mouse-embryonal/fetal calvaria fibroblasts (MC3T3-E1) were used as a model system. Thin-film platinum (Pt) sensors for respiration (amperometric oxygen electrode), acidification (potentiometric pH electrodes) and cell adhesion (interdigitated-electrodes structures, IDES) allowed us to monitor cell-physiological parameters as well as the cell-spreading behavior. Two on-chip electro-thermal micro-pumps (ETμPs) permitted the induction of medium flow in the system, e.g., for medium mixing and drug delivery. The glass-wafer technology ensured the microscopic observability of the on-chip cell culture. Connecting Pt structures were passivated by a 1.2 μm layer of silicon nitride (Si3N4). Thin Si3N4 layers (20 nm or 60 nm) were used as the sensitive material of the pH electrodes. These electrodes showed a linear behavior in the pH range from 4 to 9, with a sensitivity of up to 39 mV per pH step. The oxygen sensors were circular Pt electrodes with a sensor area of 78.5 μm(2). Their sensitivity was 100 pA per 1% oxygen increase in the range from 0% to 21% oxygen (air saturated). Two different IDES geometries with 30- and 50-μm finger spacings showed comparable sensitivities in detecting the proliferation rate of MC3T3 cells. These cells were cultured for 11 days in vitro to test the biocompatibility, microfluidics and electric sensors of our system under standard laboratory conditions.

Semiconductor sensor embedded microfluidic chip for protein biomarker detection using a bead-based immunoassay combined with deoxyribonucleic acid strand labeling

Two major issues need to be addressed in applying semiconductor biosensors to detecting proteins in immunoassays. First, the length of the antibody on the sensor surface surpasses the Debye lengths (approximately 1 nm, in normal ionic strength solution), preventing certain specifically bound proteins from being tightly attached to the sensor surface. Therefore, these proteins do not contribute to the sensor's surface potential change. Second, these proteins carry a small charge and can be easily affected by the pH of the surrounding solution. This study proposes a magnetic bead-based immunoassay using a secondary antibody to label negatively charged DNA fragments for signal amplification. An externally imposed magnetic force attaches the analyte tightly to the sensor surface, thereby effectively solving the problem of the analyte protein's distance to the sensor surface surpassing the Debye lengths. In addition, a normal ion intensity buffer can be used without dilution for the proposed method. Experiments revealed that the sensitivity can be improved by using a longer DNA fragment for labeling and smaller magnetic beads as solid support for the antibody. By using a 90 base pair DNA label, the signal was 15 times greater than that without labeling. In addition, by using a 120 nm magnetic bead, a minimum detection limit of 12.5 ng mL(-1) apolipoprotein A1 can be measured. Furthermore, this study integrates a semiconductor sensor with a microfluidic chip. With the help of microvalves and micromixers in the chip, the length of the mixing step for each immunoassay has been reduced from 1h to 20 min, and the sample volume has been reduced from 80 μL to 10 μL. In practice, a protein biomarker in a urinary bladder cancer patient's urine was successfully measured using this technique. This study provides a convenient and effective method to measure protein using a semiconductor sensor.

Targeting tumour hypoxia to prevent cancer metastasis. From biology, biosensing and technology to drug development: the METOXIA consortium

The hypoxic areas of solid cancers represent a negative prognostic factor irrespective of which treatment modality is chosen for the patient. Still, after almost 80 years of focus on the problems created by hypoxia in solid tumours, we still largely lack methods to deal efficiently with these treatment-resistant cells. The consequences of this lack may be serious for many patients: Not only is there a negative correlation between the hypoxic fraction in tumours and the outcome of radiotherapy as well as many types of chemotherapy, a correlation has been shown between the hypoxic fraction in tumours and cancer metastasis. Thus, on a fundamental basis the great variety of problems related to hypoxia in cancer treatment has to do with the broad range of functions oxygen (and lack of oxygen) have in cells and tissues. Therefore, activation-deactivation of oxygen-regulated cascades related to metabolism or external signalling are important areas for the identification of mechanisms as potential targets for hypoxia-specific treatment. Also the chemistry related to reactive oxygen radicals (ROS) and the biological handling of ROS are part of the problem complex. The problem is further complicated by the great variety in oxygen concentrations found in tissues. For tumour hypoxia to be used as a marker for individualisation of treatment there is a need for non-invasive methods to measure oxygen routinely in patient tumours. A large-scale collaborative EU-financed project 2009-2014 denoted METOXIA has studied all the mentioned aspects of hypoxia with the aim of selecting potential targets for new hypoxia-specific therapy and develop the first stage of tests for this therapy. A new non-invasive PET-imaging method based on the 2-nitroimidazole [(18)F]-HX4 was found to be promising in a clinical trial on NSCLC patients. New preclinical models for testing of the metastatic potential of cells were developed, both in vitro (2D as well as 3D models) and in mice (orthotopic grafting). Low density quantitative real-time polymerase chain reaction (qPCR)-based assays were developed measuring multiple hypoxia-responsive markers in parallel to identify tumour hypoxia-related patterns of gene expression. As possible targets for new therapy two main regulatory cascades were prioritised: The hypoxia-inducible-factor (HIF)-regulated cascades operating at moderate to weak hypoxia (<1% O(2)), and the unfolded protein response (UPR) activated by endoplasmatic reticulum (ER) stress and operating at more severe hypoxia (<0.2%). The prioritised targets were the HIF-regulated proteins carbonic anhydrase IX (CAIX), the lactate transporter MCT4 and the PERK/eIF2α/ATF4-arm of the UPR. The METOXIA project has developed patented compounds targeting CAIX with a preclinical documented effect. Since hypoxia-specific treatments alone are not curative they will have to be combined with traditional anti-cancer therapy to eradicate the aerobic cancer cell population as well.

Pericellular oxygen monitoring with integrated sensor chips for reproducible cell culture experiments

OBJECTIVES

Here we present an application, in two tumour cell lines, based on the Sensing Cell Culture Flask system as a cell culture monitoring tool for pericellular oxygen sensing.

MATERIALS AND METHODS

T-47D (human breast cancer) and T98G (human brain cancer) cells were cultured either in atmospheric air or in a glove-box set at 4% oxygen, in both cases with 5% CO2 in the gas phase. Pericellular oxygen tension was measured with the help of an integrated sensor chip comprising oxygen sensor arrays.

RESULTS

Obtained results illustrate variation of pericellular oxygen tension in attached cells covered by stagnant medium. Independent of incubation conditions, low pericellular oxygen concentration levels, usually associated with hypoxia, were found in dense cell cultures.

CONCLUSIONS

Respiration alone brought pericellular oxygen concentration down to levels which could activate hypoxia-sensing regulatory processes in cultures believed to be aerobic. Cells in culture believed to experience conditions of mild hypoxia may, in reality, experience severe hypoxia. This would lead to incorrect assumptions and suggests that pericellular oxygen concentration readings are of great importance to obtain reproducible results when dealing with hypoxic and normoxic (aerobic) incubation conditions. The Sensing Cell Culture Flask system allows continuous monitoring of pericellular oxygen concentration with outstanding long-term stability and no need for recalibration during cell culture experiments. The sensor is integrated into the flask bottom, thus in direct contact with attached cells. No additional equipment needs to be inserted into the flask during culturing. Transparency of the electrochemical sensor chip allows optical inspection of cells attached on top of the sensor.

Cell culture monitoring for drug screening and cancer research: a transparent, microfluidic, multi-sensor microsystem

We present a novel, multiparametric microphysiometry system for the dynamic online monitoring of human cancer cell metabolism. The optically transparent, modular, hybrid microsystem is based on a glass chip and combines a cell cultivation chamber, microfluidics and metabolic monitoring with fully integrated chemo- and biosensors. pH and oxygen are measured in the cell culture area, and biosensors for lactate and glucose are connected downstream by microfluidics. The wafer-level fabrication features thin-film platinum and iridium oxide microelectrodes on a glass chip, microfluidics in an epoxy resist, a hybrid assembly and an on-chip reference electrode. The reliable analytical performance of the sensors in cell culture medium was demonstrated. The pH sensors exhibit a long-term stable, linear response. The oxygen sensors show a linear behaviour, which is also observed for low oxygen concentrations. Glucose and lactate measurements show a linear, long-term stable, selective and reversible behaviour in the desired range. T98G human brain cancer cells were cultivated and cell culture metabolism was measured on-chip. Stop/flow cycles were applied and extracellular acidification, respiration, glucose consumption and lactate production were quantified. Long-term metabolic rates were determined and all parameters could be measured in the outlet channel. A placement downstream of the cell cultivation area for biosensors was realised. A highly effective medium exchange and undiluted sampling from the cell culture chamber with low flow rates (2 μl min(-1)) and low volumes (15 μl per cycle) were achieved. The drug screening application was demonstrated by detecting alteration and recovery effects of cellular metabolism induced by the addition of substances to the medium.

Note: in vivo pH imaging system using luminescent indicator and color camera

Microscopic in vivo pH imaging system is developed that can capture the luminescent- and color-imaging. The former gives a quantitative measurement of a pH distribution in vivo. The latter captures the structural information that can be overlaid to the pH distribution for correlating the structure of a specimen and its pH distribution. By using a digital color camera, a luminescent image as well as a color image is obtained. The system uses HPTS (8-hydroxypyrene-1,3,6-trisulfonate) as a luminescent pH indicator for the luminescent imaging. Filter units are mounted in the microscope, which extract two luminescent images for using the excitation-ratio method. A ratio of the two images is converted to a pH distribution through a priori pH calibration. An application of the system to epidermal cells of Lactuca Sativa L is shown.

Cell-based sensor system using L6 cells for broad band continuous pollutant monitoring in aquatic environments

Pollution of drinking water sources represents a continuously emerging problem in global environmental protection. Novel techniques for real-time monitoring of water quality, capable of the detection of unanticipated toxic and bioactive substances, are urgently needed. In this study, the applicability of a cell-based sensor system using selected eukaryotic cell lines for the detection of aquatic pollutants is shown. Readout parameters of the cells were the acidification (metabolism), oxygen consumption (respiration) and impedance (morphology) of the cells. A variety of potential cytotoxic classes of substances (heavy metals, pharmaceuticals, neurotoxins, waste water) was tested with monolayers of L6 cells (rat myoblasts). The cytotoxicity or cellular effects induced by inorganic ions (Ni²⁺ and Cu²⁺) can be detected with the metabolic parameters acidification and respiration down to 0.5 mg/L, whereas the detection limit for other substances like nicotine and acetaminophen are rather high, in the range of 0.1 mg/L and 100 mg/L. In a close to application model a real waste water sample shows detectable signals, indicating the existence of cytotoxic substances. The results support the paradigm change from single substance detection to the monitoring of overall toxicity.

Multi-sensor arrays for online monitoring of cell dynamics in in vitro studies with choroid plexus epithelial cells

Sensors and multi-sensor arrays are the basis of new technologies for the non-label monitoring of cell activity. In this paper we show that choroid plexus cells can be cultured on silicon chips and that sensors register in real time changes in their activity, constituting an interesting experimental paradigm for cell biology and medical research. To validate the signals recorded (metabolism = peri-cellular acidification, oxygen consumption = respiration; impedance = adhesion, cell shape and motility) we performed experiments with compounds that act in a well-known way on cells, influencing these parameters. Our in vitro model demonstrates the advantages of multi-sensor arrays in assessment and experimental characterization of dynamic cellular events—in this case in choroid plexus functions, however with applicability to other cell types as well.

Towards the realization of label-free biosensors through impedance spectroscopy integrated with IDES technology

Impedance spectroscopy (IS) is a powerful technique for analysis of the complex electrical impedance of a large variety of biological systems, because it is sensitive both to surface phenomena and to changes of bulk properties. A simple and convenient method of analysis of cell properties by IS is described. An interdigitated electrodes configuration was used for the measurements; human epithelial cells were grown on the device to investigate the complex dielectric response as a function of frequency, in order to test the suitability of the device for use as a label-free biosensor. To test the ability of the device to detect channels in the cell membrane, the effect of drugs known to affect membrane integrity was also investigated. The frequency response of the admittance (i.e. the reciprocal of the impedance) can be well fitted by a model based on very simple assumptions about the cells coating the device surface and the current flow; from the calculations, membrane-specific capacitance and information about cell adhesion can be inferred. These preliminary efforts have shown that our configuration could lead to a label-free non-invasive technique for biosensing and cellular behavior monitoring which might prove useful in investigation of the basic properties of cells and the effect of drugs by estimation of some fundamental properties and modification of the electrical characteristics of the device.

A decrease of intracellular ATP is compensated by increased respiration and acidification at sub-lethal parathion concentrations in murine embryonic neuronal cells: measurements in metabolic cell-culture chips

We present a label-free in vitro method for testing the toxic potentials of chemical substances using primary neuronal cells. The cells were prepared from 16-day-old NMRI mouse embryos and cultured on silicon chips (www.bionas.de) under the influence of different parathion concentrations with sensors for respiration (Clark-type oxygen electrodes), acidification (pH-ISFETs) and cell adhesion (interdigitated electrode structures, IDES). After 12 days in vitro, the sensor readouts were simultaneously recorded for 350 min in the presence of parathion applying a serial 1:3 dilution. The parathion-dependent data was fitted by logistic functions. IC(50) values of approximately 105 μM, 65 μM, and 54 μM were found for respiration, acidification, and adhesion, respectively. An IC(50) value of approximately 36 μM was determined from the intracellular ATP-levels of cells, which were detected by an ATP-luminescence assay using micro-well plates. While the intracellular ATP level and cell adhesion showed no deviation from a simple logistic decay, increases of approximately 29% in the respiration and 15% in the acidification rates above the control values were found at low parathion concentrations, indicating hormesis. These increases could be fitted by a modified logistic function. We believe that the label-free, continuous, multi-parametric monitoring of cell-metabolic processes may have applications in systems-biology and biomedical research, as well as in environmental monitoring. The parallel characterization of IC(50) values and hormetic effects may provide new insights into the metabolic mechanisms of toxic challenges to the cell.

The open container-used microfluidic chip using IrO(x) ultramicroelectrodes for the in situ measurement of extracellular acidification

The measurement of metabolic activity based on the extracellular acidification rate has attracted wide interests in the field of biochemical detection. In the study, the chip comprising a microfluid-controlled open container and iridium oxide (IrO(x)) pH ultramicroelectrodes (UMEs) was constructed for the purpose of in situ measurement of extracellular acidification rate. The feasible anodic depositing parameters of IrO(x) film were in the range of +0.53 to +0.8 V by means of exploring the electrochemical properties of alkaline Ir(IV) deposition solution. The IrO(x) pH UMEs electrodeposited for 300 cycles between 0 V and +0.6 V exhibited the near-super-Nernstian sensitivity of -68 to -76 mV/pH and the good stability with potential drifting of 11.7 mV within 24h. The design of the open container connected with a position-raised microchannel improved the sensing stability of IrO(x) pH UMEs, with the potential deviation of as low as 0.1 mV under the flow rate of 20 μl/min. The acidification rate of HeLa cells (2160 cells/mm(2)) repeatedly measured 5 times in the microfluidic chip showed the good reproducibility of 0.021±0.002 pH/min. Moreover, the chip can decrease the acidosis occurrence, a decrease of only 0.13-0.17 pH unit in 8 min interval, during the measurement of cellular metabolic activity.

Investigation of Cell-Sensor Hybrid Structures by Focused Ion Beam (FIB) Technology

For the investigation of the adhesion of mammalian cells on a semiconductor biosensor structure, nerve cells on silicon neurochips were prepared for scanning electron microscopy investigations (SEM) and cross-sectional preparation by focused ion beam technology (FIB). The cross-sectional pattern demonstrates the focal adhesion points of the nerve cells on the chip. Finally, SEM micrographs were taken parallel to the FIB ablation to investigate the cross section of the cells slice by slice in order to demonstrate the spatial distribution of focal contact positions for a possible three-dimensional reconstruction of the cell-silicon interface.

Modular glass chip system measuring the electric activity and adhesion of neuronal cells--application and drug testing with sodium valproic acid

We developed a modular neurochip system by combining a small (16x16 mm2) glass neurochip (GNC) with a homemade head stage and commercial data acquisition hardware and software. The system is designed for the detection of the electric activity of cultivated nerve or muscle cells by a 52-microelectrode array (MEA). In parallel, cell adhesion can be registered from the electric impedance of an interdigitated electrode structure (IDES). The GNC was tested with various cell lines and primary cells. It is fully autoclavable and re-useable. Murine embryonic primary cells were used as a model system to correlate the electric activity and adhesion of neuronal networks in a drug test with sodium valproic acid. The test showed the advantage of the parallel IDES and MEA measurements, i.e. the parallel detection of cytotoxic and neurotoxic effects. Toxic exposure of the cells during neuronal network formation allows for the characterization of developmental neurotoxic effects even at drug concentrations below the EC50-value for acute neurotoxic effects. At high drug concentrations, the degree of cytotoxic damage can still be assessed from the IDES data in the event that no electric activity develops. The GNC provides optimal cell culture conditions for up to months in combination with full microscopic observability. The 4'' glass wafer technology allows for a high precision of the GNC structures and an economic production of our new system that can be applied in general and developmental toxicity tests as well as in the search for neuro-active compounds.

A Clark-type oxygen chip for in situ estimation of the respiratory activity of adhering cells

A Clark-type oxygen chip consisting of a polydimethylsiloxane (PDMS) reservoir containing an amino group-modified PDMS oxygen-permeable membrane (OPM) and a glass substrate containing a three-electrode detector has been constructed by using microfabrication techniques, and it is utilized for in situ measurement of the respiration activity of adhering cells. Use of the alginate sol electrolyte and the electroplating Ag/AgCl pseudo-reference electrode can effectively diminish the crosstalk between the electrochemical electrodes and supply a stable potential for the detection of dissolved oxygen, respectively. The Clark-type oxygen chips possess only 1.00% residual current, response time of 13.4s and good linearity with a correlation coefficient of 0.9933. The modification of amino groups for the OPM obviously facilitates the adhesion of HeLa cells onto the PDMS OPM surface and allows the cells to spread after 2h of incubation. The oxygen consumption of the cells in the cell-adhesion process increases with the adhesion time, and the increment of cellular oxygen consumption per minute reaches a maximum after 30 min of incubation. Moreover, the change in the respiration activity of adhering HeLa cells stimulated by the high concentration of glucose or propofol anaesthetic can be monitored in real time with the Clark-type oxygen chip.

Ion-sensitive field-effect transistor for biological sensing

In recent years there has been great progress in applying FET-type biosensors for highly sensitive biological detection. Among them, the ISFET (ion-sensitive field-effect transistor) is one of the most intriguing approaches in electrical biosensing technology. Here, we review some of the main advances in this field over the past few years, explore its application prospects, and discuss the main issues, approaches, and challenges, with the aim of stimulating a broader interest in developing ISFET-based biosensors and extending their applications for reliable and sensitive analysis of various biomolecules such as DNA, proteins, enzymes, and cells.

The Bionas technology for anticancer drug screening

BACKGROUND

The Bionas 2500(®) analyzing system is an advanced label-free technology using a cell-based multi-sensor array, which is commercially available. Data on metabolism, respiration, adhesion, cell proliferation and cell death rates, as well as ligand-receptor interactions (multi-parametric) can be acquired and statistically evaluated. Noteworthy is the possibility of analyzing later after effects and/or recovery after drug treatment. In addition, Bionas supports all conceivable drug application modes (one, two or more drugs). Specimens for drug screening with Bionas consist of human permanent cell lines, primary cell cultures as well as 'tumor slices' obtained from biopsies and surgery material.

OBJECTIVE/METHODS

Examples of measurements are presented and discussed.

CONCLUSION

Although drug throughput is modest, the high quality of the information allows in-depth evaluation.

Electronic interfacing with living cells

The direct interfacing of living cells with inorganic electronic materials, components or systems has led to the development of two broad categories of devices that can (1) transduce biochemical signals generated by biological components into electrical signals and (2) transduce electronically generated signals into biochemical signals. The first category of devices permits the monitoring of living cells, the second, enables control of cellular processes. This review will survey this exciting area with emphasis on the fundamental issues and obstacles faced by researchers. Devices and applications that use both prokaryotic (microbial) and eukaryotic (mammalian) cells will be covered. Individual devices described include microbial biofuel cells that produce electricity, bioelectrical reactors that enable electronic control of cellular metabolism, living cell biosensors for the detection of chemicals and devices that permit monitoring and control of mammalian physiology.

Field-effect devices for detecting cellular signals

The integration of living cells together with silicon field-effect devices challenges a new generation of biosensors and bioelectronic devices. Cells are representing highly organised complex systems, optimised by millions of years of evolution and offering a broad spectrum of bioanalytical receptor "tools" such as enzymes, nucleic acids proteins, etc. Their combination with semiconductor-based electronic chips allows the construction of functional hybrid systems with unique functional and electronic properties for both fundamental studies and biosensoric applications. This review article summarises recent advances and trends in research and development of cell/transistor hybrids (cell-based field-effect transistors) as well as light-addressable potentiometric sensors.

Online monitoring of BALB/3T3 metabolism and adhesion with multiparametric chip-based system

A multiparametric chip-based system was employed to measure cell adhesion, metabolism, and response to metal compounds previously classified as cytotoxic in immortalized mouse fibroblasts (BALB/3T3 cell line). The system measures in parallel, online, and in label-free conditions the extracellular acidification rates (with pH-sensitive field effect transistors [ISFETs]), the cellular oxygen consumption (with amperometric electrode structures [Clark-type sensors]), and cell adhesion (with impedimetric interdigitated electrode structures [IDESs]). The experimental protocol was optimized to monitor metabolism and adhesion of the BALB/3T3 cell line. A total of 70,000 cells and a bicarbonate buffer-free running low-glucose Dulbecco's modified Eagle's medium (DMEM) containing 10% fetal clone serum III and 1mM Hepes were selected to maintain cells in good conditions on the chip during the measurements performed under perfusion conditions. Cells were exposed to sodium arsenite, cadmium chloride, and cis-platinum at concentrations ranging from 1 to 100 microM. The kinetics of cell response to these compounds was analyzed and suggests that the Clark-type sensors can be more sensitive than IDESs and ISFETs in detecting the presence of high chemical concentration when short exposure times (i.e., 2h) are considered. The cytotoxicity data obtained from the online measurements of acidification, respiration, and adhesion at 24h compare well, in terms of half-inhibition concentration values (IC(50)), with the ones obtained using 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) test and colony-forming efficiency (CFE) assay. The results show a good sensitivity of the system combined with the advantages of the online and label-free detection methods that allow following cell status before, during, and after the treatment in the same experiment.

AlGaN/GaN heterostructures for non-invasive cell electrophysiological measurements

Recently, the ability to create bio-semiconductor hybrid devices has gained much interest for cell activity analysis. AlGaN material system has been demonstrated to be a promising cell-based biosensing platform due to a combination of unique properties, such as chemical inertness, optical transparency and low signal to noise ratios. To investigate the potential application of hybrid cell-AlGaN/GaN field effect transistor for cell electrophysiological monitoring, saos-2 human osteoblast-like cells were cultured in high density in non-metallized gate area of a transparent AlGaN/GaN heterostructure field effect transistor. We implemented and characterized the transistor recording of extracellular voltage in the cell-chip junction using the FET chip. The effect of ion channel blocker TEA on transistor signal was explored in order to test the capability of this hybrid chip for in vitro drug screening bioassay. Finally, the effect of cell adhesion on transistor signal was also studied by applying the protein kinase inhibitor H-7.

Towards the silicon nanowire-based sensor for intracellular biochemical detection

A microneedle sensor platform with integrated silicon nanowire tip was developed for intracellular biochemical detection. Because of the virtue of miniaturized size and high sensitivity, this sensor has a great potential for studying individual cell or localized bioenvironment by revealing the pH level and/or enzyme activities. The fabrication of the microneedle sensor was primarily based on conventional silicon processing, where a silicon-on-insulator (SOI) wafer with 50 nm thick (100) p-type Si device layer was used as the substrate. The silicon nanowires of 50 nm height and 50-100 nm width were created by electron beam (E-beam) lithography on the tip of microneedle with good electrical connection to the contact pads for convenient electrical measurement. A three layer structure with base, support cantilever, and needle tip was designed to ensure convenient handling of sensors and minimize the invasive penetration into biological cells. In this paper, we demonstrate a preliminary assessment of this novel intracellular sensor with electrical conductance measurement under different pH levels. It is expected that this sensor with proper chemical modification will enable localized biochemical sensing within biological cells, such as neurotransmitter activities during the synaptic communication between neuron cells.

Online monitoring of cell metabolism for studying pharmacodynamic effects

To characterize modes of action of substances and their cytotoxic effects Bionas GmbH has developed a new screening system to allow the continuous recording of how an active substance can act (Bionas 2500 analyzing system). In the pharmaceutical industry it is important to acquire as much information as possible about the metabolic effects of an active substance. Most classical pre-clinical studies are very expensive and time-consuming. Often they are so-called end-point tests which require many individual tests before approximate statements can be made about how an effect takes its course. With the Bionas 2500 analyzing system metabolically relevant data including oxygen consumption, acidification rate and the adhesion (cell impedance) of cells can be measured in parallel, online and label-free. Using e.g. ion-sensitive field effect-transistors (ISFET) and electrode structures it is possible to observe metabolic parameters non-invasively and continuously over longer periods of time. The system has already been established for several cell models, cell lines as well as primary cells. It also offers the advantage that regenerative effects can be observed during the same test run.

A new exposure system for the in vitro detection of GHz field effects on neuronal networks

The possible effects of high-frequency electromagnetic fields (EMF) on biological systems are a subject of public concern and scientific discussion. It is generally accepted that the absorption of part of the field energy may cause a temperature rise in biological tissue. Nevertheless, our setup aims to detect possible athermal effects on the electric activity of neuronal in vitro networks. Such networks were formed by primary neurons derived from the murine frontal cortex and cultivated on micro-sensor chips. The action potentials of the neurons were detected in real time by an integrated, electrically passive microelectrode array. For EMF exposure, the chips were introduced into a rectangular wave-guide that could be operated in the propagating or standing wave modes. The drive signals were either continuous waves (1.9-2.2 GHz) or a generic mobile phone signal (UMTS-standard) of up to approximately 8 W. An on-chip sensor allowed the temperature progression to be recorded. In addition, ISFETs and Clark-like electrodes were integrated for the on-chip detection of pH and O(2), respectively.

A New Method to Assess Drug Sensitivity on Breast Tumor Acute Slices Preparation

A method for assessing tumor drug sensitivity is described that is based on preparation of tissue slices and use of silicon chips equipped with electrochemical sensors (multisensor array). The tumor slices (200-300 microM thick) are prepared after surgery and incubated in a medium for recovery after slicing. The advantage, compared to other preparations, is that the original three-dimensional structure is retained. Multisensor arrays measure: (a) pericellular acidification (anaerobic metabolism) and (b) oxygen consumption (respiration). The innovative aspect is that such measurements can be made online, as opposed to using a large battery of endpoint tests on cell vitality and proliferation. Electron microscopy of slices serves to determine cell density and structure and induction of apoptosis/necrosis. Slices of more than 200 breast tumors were used. Metabolic activity was inhibited by sodium fluoride, which reduces glycolysis, and potassium cyanide, which inhibits respiration. These changes are thus reflected in the curves of acidification and oxygen consumption. In other experiments the cytostatic Taxol, an anticytoskeletal agent, was used showing dose and time-dependent effects on acidification and oxygen consumption. In conclusion, the method presented here, is able to provide information on drug sensitivity of a tumor, which aids in designing individualized therapy and is used for drug screening.