Development of analytical methods for polycyclic aromatic hydrocarbons (PAHs) in airborne particulates: a review

Comprehensive methodology for semi-volatile organic compound determination in ambient air with emphasis on polycyclic aromatic hydrocarbons analysis by GC-MS/MS

Polycyclic aromatic hydrocarbons are air pollutants that affect the human health and the environment, and their accurate determination in outdoor and indoor environments is important. This study presents a methodology for sampling and analysis of semi-volatile compounds in ambient air with emphasis on the polycyclic aromatic hydrocarbons, collected with low-volume pumps (4.8 m3) in unconditioned solid phase extraction cartridges (Isolute ENV+). Sampling in SPE cartridges with low-volume pumps allows the collection of both gas and particulate phase compounds in indoor as well as outdoor environments, and reduces the number of extraction steps required as well as the solvent volume used for extraction. Analysis of the 16 US-EPA priority PAHs after extraction was conducted by GC-MS/MS with recoveries of the PAHs 40-118 %. No breakthrough was detected during sampling. Moreover, the methodology includes storage test to assess the conservation of PAHs in the SPE cartridges in heat-sealable Kapac bags; simulating transport from sampling sites to laboratory, and storage under room, cold and frozen conditions at different time-intervals, up to 3 months after sampling. The results showed that concentration levels remained constant across various storage time intervals and temperatures, with naphthalene and acenaphthylene being the only exceptions, showing high blank levels for the first and losses at room temperature for the later. The method quantification limits, including sampling, storage and GC-MS/MS analysis ranged from 2000 pg m-3 for naphthalene and 300 pg m-3 for phenanthrene to less than 20.0 pg m-3 for higher molecular and less volatile PAHs, such as benzo[a]pyrene (LOQ = 8.0 pg m-3). The feasibility of the method was tested by sampling indoors under urban background air conditions, showing individual PAH concentrations 4 to 10 times higher than their method quantification limits.

Characterizing PM2.5 Emissions and Temporal Evolution of Organic Composition from Incense Burning in a California Residence

The chemical composition of incense-generated organic aerosol in residential indoor air has received limited attention in Western literature. In this study, we conducted incense burning experiments in a single-family California residence during vacancy. We report the chemical composition of organic fine particulate matter (PM2.5), associated emission factors (EFs), and gas-particle phase partitioning for indoor semivolatile organic compounds (SVOCs). Speciated organic PM2.5 measurements were made using two-dimensional gas chromatography coupled with high-resolution time-of-flight mass spectrometry (GC×GC-HR-ToF-MS) and semivolatile thermal desorption aerosol gas chromatography (SV-TAG). Organic PM2.5 EFs ranged from 7 to 31 mg g-1 for burned incense and were largely comprised of polar and oxygenated species, with high abundance of biomass-burning tracers such as levoglucosan. Differences in PM2.5 EFs and chemical profiles were observed in relation to the type of incense burned. Nine indoor SVOCs considered to originate from sources other than incense combustion were enhanced during incense events. Time-resolved concentrations of these SVOCs correlated well with PM2.5 mass (R2 > 0.75), suggesting that low-volatility SVOCs such as bis(2-ethylhexyl)phthalate and butyl benzyl phthalate partitioned to incense-generated PM2.5. Both direct emissions and enhanced partitioning of low-volatility indoor SVOCs to incense-generated PM2.5 can influence inhalation exposures during and after indoor incense use.

HPLC Analysis and Risk Assessment of 15 Priority PAHs in Human Blood Serum of COPD Patient from Urban and Rural Areas, Iasi (Romania)

One of the leading risk factors for environmental health problems is air pollution. The World Health Organization (WHO) reports that this risk factor is associated with one of every nine deaths worldwide. Epidemiological studies conducted in this field have shown a solid connection between respiratory pathology and polycyclic aromatic hydrocarbon (PAH) exposure. COPD and asthma are respiratory diseases that were shown to have a strong association with exposure to PAHs. The purpose of the present study was to assess the serum levels of 15 PAHs in 102 COPD patients and to evaluate the results according to the residence environment of the investigated subjects. Analyses were carried out using a high-performance liquid chromatograph Nexera X2-Shimadzu Japan, which was equipped with an LC-30AD pump and an SIL-30AC autosampler. Spiked matrices, procedure blanks, spiked controls, and calibration standards in the acetonitrile were used as quality-assurance samples. Benzo(a)pyrene is the main representative of PAHs and was determined in higher concentrations in subjects with COPD versus the control group from the urban area (0.90/0.47 ng/mL) and rural area (0.73/0.44 ng/mL). The values obtained for the Benzo(a)pyrene-equivalent factor indicate a higher carcinogenic potential for patients diagnosed with COPD in urban areas compared to those in rural areas. These results could be due to traffic and vehicle emissions. This research identifies the need for legislative action to decrease semi-volatile organic compounds, especially PAHs, mainly in urban cities, in order to improve environmental management and health conditions.

A simple device for simulating skin adsorption of polycyclic aromatic hydrocarbons: design and application

Dermal exposure is one of the main ways of human body exposure to atmospheric contaminants such as polycyclic aromatic hydrocarbons (PAHs). The skin type significantly affects the skin adsorption of contaminants. However, this is commonly ignored in assessing the dermal exposure based on the atmospheric concentrations of contaminants. In this study, a simulation device suitable for human dermal pollutant exposure assessment was established, which used polyethylene balloons coated with different doses of glycerol trioleate to simulate oily skin, neutral skin, and dry skin type. The sampling effectiveness of the device was verified, and the device was applied to the skin exposure assessment of atmospheric PAHs at different scenarios. Kinetic experiments indicated a linear adsorption within 6 h. The adsorption kinetic constants (k) of PAHs on the oily surface of the balloon were significantly higher than those on the dry surface, especially for PAHs with high ring numbers. Compared with the calculated skin adsorption based on atmospheric concentrations, the results of this simulation device can better simulate the skin adsorption of atmospheric contaminants on different skin types and in different scenarios. Based on the result of balloon sampling, the dermal exposure of PAH_{3 rings} by oily skin inside the tunnel is up to 5.668 ng/cm²/day, indicating a non-negligible health risk.

Contemporary Research Progress on the Detection of Polycyclic Aromatic Hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are a class of the most common and widespread contaminants. The accumulation of PAHs has made a certain impact on the environment and is seriously threatening human health. Numerous general analytical methods suitable for PAHs were developed. With the development of economy, the environmental problems of PAHs in modern society are more extensive and prominent, and attract more attention from environmental scientists and analysts. Deeper understanding of the properties of PAHs depends on the advent of detection methods, which can also be more conducive to promoting the protection of the environment. Till now, more sensitive, more high-speed and more high-throughput analytical tools are being invented and have played important roles in the research of PAHs. In this short review article, we focused mainly on the contemporary analytical methods about PAHs. We started with a brief review on the hazards, migration, distribution and traditional analysis methods of PAHs in recent years, including liquid chromatography, gas chromatography, surface enhanced Raman spectroscopy and so on. We also presented the applications of the modern ambient mass spectrometry, especially microwave plasma torch mass spectrometry, in the detection of PAHs, as well as the far out novel results in our lab by using microwave plasma torch (MPT) mass spectrometry; for example, some new insights about Birch reduction, regular hydrogen addition and the robustness of molecular structure. These studies have demonstrated the versatility of MPT MS as a platform in the research of PAHs.

Diet, exposure to polycyclic aromatic hydrocarbons during pregnancy, and fetal growth: A comparative study of mothers and their fetuses in industrial and urban areas in Southwest Iran

The presence of polycyclic aromatic hydrocarbons (PAHs) in the fetal environment is a high-priority concern due to the fetus being more sensitive than adults to these ubiquitous xenobiotics. The aim of the present study was to compare the maternal and fetal serum levels of ΣPAHs and their effects on fetal growth in an industrial and an urban area in Southwest Iran. The industrial area was the petrochemical and gas area (PGA) of the Central District of Asaluyeh County and the urban area (UA) was the Central District of Bushehr County, Ninety-nine maternal serum (MS) and 99 cord serum (CS) samples from the PGA and 100 MS and 100 CS samples from the UA were collected during May 2018 to February 2019. The mean concentrations of ΣPAHs were significantly (p < 0.05) higher in the PGA than the UA in both MS (157.71 vs. 93.56 μg/L) and CS (155.28 vs. 93.19 μg/L) samples. Naphthalene (NAP) was the predominant PAH detected in all the studied samples. Significant negative associations were found between birth weight and anthracene (ANT) level in MS (β = -22.917, p = 0.032; weight decrement = 22.917 g for a 1 μg/L increase in ANT); head circumference and chrysene (CHR) level in MS (β = -0.206, p = 0.023; head circumference decrement = 0.206 cm for a 1 μg/L increase in CHR); and birth height and NAP level in CS (β = -0.20, p = 0.005; height decrement = 0.20 cm for a 1 μg/L increase in NAP). Maternal diet had a significant effect on the serum levels of PAHs. The results of this study showed that transmission of PAHs from mother to fetus through the cord blood is an important issue and mothers who live in industrial areas and consume PAH-containing foodstuffs, and their fetuses, are more at risk than those living in a non-industrial urban area.

Polycyclic Aromatic Hydrocarbons: Occurrence, Electroanalysis, Challenges, and Future Outlooks

The past several decades have seen increasing concern regarding the wide distribution of polycyclic aromatic hydrocarbons (PAHs) in environmental matrices. Primary toxicological data show PAHs' persistent characteristics and possible toxicity effects. Because of this pressing global issue, electroanalytical methods have been introduced. These methods are effective for PAH determination in environmental waters, even outclassing sophisticated analytical techniques such as chromatography, conventional spectrophotometry, fluorescence, and capillary electrophoresis. Herein, the literature published on PAHs is reviewed and discussed with special regard to PAH occurrence. Moreover, the recent developments in electrochemical sensors for PAH determination and the challenges and future outlooks in this field, are also presented.

Investigation of geospatial distribution of PAH compounds in soil phase and determination of soil-air exchange direction in a megacity

In this study, determination of possible sources, soil-air exchange direction, and spatial distribution of PAH concentrations was aimed. In this scope, soil samples were collected from 35 different points, which have the urban and rural characteristics, from European and Asian Sides in Istanbul. The average ∑₁₆PAH concentrations were found as 22.11 ng/g dw for urban site and 19.53 ng/g dw for rural site, respectively. The highest concentration was 279.5 ng/g dw. PAH concentrations were higher in urban site than rural site. Acenaphthene and benzo[k]fluoranthene were observed as the dominant species. PAH concentrations are observed higher mostly in north and west parts of European Side and south and east parts of Asian Side. There was net evaporation from soil to air for lower molecular weight PAHs with 2, 3 rings, while high molecular weight PAHs with 4, 5, 6 rings accumulated in the soil at both urban and rural sites. PAHs were mostly originated from coal burning and the use of diesel engine vehicles.

A critical review on plant biomonitors for determination of polycyclic aromatic hydrocarbons (PAHs) in air through solvent extraction techniques

Polycyclic aromatic hydrocarbons (PAHs) are hydrocarbons having two or more fused aromatic rings, released from natural (like forest fires and volcanic eruption) as well as man-made sources (like burning of fossil fuel & wood, automobile emission). They are persistent priority pollutants and continue to last for a long time in the environment causing severe damage to human health owing to their genotoxicity, mutagenicity and carcinogenicity. The study of PAHs in environment has therefore aroused a global concern. PAHs adsorption to plant cell wall is facilitated by transpiration and plant root lipids which help PAHs transfer from roots to leaves and stalks, causing more accumulation of contaminants with the increase in lipid content. Hence, these bioaccumulators can be utilized as biomonitors for indirect assessment of ambient air pollution. Efficacy of specific plants, lichens and mosses as useful biomonitors of airborne PAHs pollution has been discussed in this review along with prevalent classical and modified extraction techniques coupled with proper analytical procedures in order to gain an insight into the assessment of atmospheric PAHs concentrations. Different modern and modified solvent extraction techniques along with conventional Soxhlet method are identified for extraction of PAHs from accumulative bioindicators and analytical methods are also developed for accurate determination of PAHs. Process parameters like choice of solvent, temperature, time of extraction, pressure and matrix characteristics are usually checked. An approach of biomonitoring of PAHs using plants, lichens and mosses has been discussed here as they usually trap the atmospheric PAHs and mineralize them.

Size distribution of particulate polycyclic aromatic hydrocarbons in fresh combustion smoke and ambient air: A review

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous in the atmosphere and they mostly stem from the imperfect combustion of fossil fuels and biofuels. PAHs are inherently associated with homogenous fine particles or distributed to different-sized particles during the aging of air masses. PAHs carried by fine particles undergo a long-range transport to remote areas while those adsorbed on coarse particles have a shorter lifetime in ambient air. More importantly, PAHs with higher molecular weights tend to be bound with finer particles and can deeply enter the lungs, posing severe health risks to humans. Thus, the environmental fate and health effects of particulate PAHs are strongly size-dependent. This review summarizes the size distributions of particulate PAHs freshly emitted from combustion sources as well as the distribution patterns of PAHs in ambient particles. It was found that PAHs from stationary sources are primarily bound to fine particles, which are slightly larger than particles to which PAHs from mobile sources are bound. In ambient air, particulate PAHs are distributed in larger size modes than those in the combustion fume, and the particle size decreases with PAH molecular weight increasing. The relevant mechanisms and influencing factors of particle size distribution changes are illustrated in this article, which are essentially attributed to combustion and ambient temperature as well as the physical and chemical properties of PAHs. Overall, the study on the particle size distribution of PAHs will contribute for a full understanding of the origin, atmospheric behaviors and health effects of particulate PAHs.

A sensor array for the discrimination of polycyclic aromatic hydrocarbons using conjugated polymers and the inner filter effect

The inner filter effect and multivariate array sensing using conjugated polymers are combined for the detection and challenging discrimination of closely related polycyclic aromatic hydrocarbons.

Natural and anthropogenic activities result in the production of polycyclic aromatic hydrocarbons (PAHs), persistent pollutants that negatively impact the environment and human health. Rapid and reliable methods for the detection and discrimination of these compounds remains a technological challenge owing to their relatively featureless properties, structural similarities, and existence as complex mixtures. Here, we demonstrate that the inner filter effect (IFE), in combination with conjugated polymer (CP) array-based sensing, offers a straightforward approach for the quantitative and qualitative profiling of PAHs. The sensor array was constructed from six fluorescent fluorene-based copolymers, which incorporate side chains with peripheral 2-phenylbenzimidazole substituents that provide spectral overlap with PAHs and give rise to a pronounced IFE. Subtle structural differences in copolymer structure result in distinct spectral signatures, which provide a unique “chemical fingerprint” for each PAH. The discriminatory power of the array was evaluated using linear discriminant analysis (LDA) and principal component analysis (PCA) in order to discriminate between 16 PAH compounds identified as priority pollutants by the US Environmental Protection Agency (EPA). This array is the first multivariate system reliant on the modulation of the spectral signatures of CPs through the IFE for the detection and discrimination of closely related polynuclear aromatic species.

Trends in analytical techniques applied to particulate matter characterization: A critical review of fundaments and applications

Epidemiological studies have shown the association of airborne particulate matter (PM) size and chemical composition with health problems affecting the cardiorespiratory and central nervous systems. PM also act as cloud condensation nuclei (CNN) or ice nuclei (IN), taking part in the clouds formation process, and therefore can impact the climate. There are several works using different analytical techniques in PM chemical and physical characterization to supply information to source apportionment models that help environmental agencies to assess damages accountability. Despite the numerous analytical techniques described in the literature available for PM characterization, laboratories are normally limited to the in-house available techniques, which raises the question if a given technique is suitable for the purpose of a specific experimental work. The aim of this work consists of summarizing the main available technologies for PM characterization, serving as a guide for readers to find the most appropriate technique(s) for their investigation. Elemental analysis techniques like atomic spectrometry based and X-ray based techniques, organic and carbonaceous techniques and surface analysis techniques are discussed, illustrating their main features as well as their advantages and drawbacks. We also discuss the trends in analytical techniques used over the last two decades. The choice among all techniques is a function of a number of parameters such as: the relevant particles physical properties, sampling and measuring time, access to available facilities and the costs associated to equipment acquisition, among other considerations. An analytical guide map is presented as a guideline for choosing the most appropriated technique for a given analytical information required.

Analysis of Polycyclic Aromatic Hydrocarbons in Ambient Aerosols by Using One-Dimensional and Comprehensive Two-Dimensional Gas Chromatography Combined with Mass Spectrometric Method: A Comparative Study

Advanced separation technology paired with mass spectrometry is an ideal method for the analysis of atmospheric samples having complex chemical compositions. Due to the huge variety of both natural and anthropogenic sources of organic compounds, simultaneous quantification and identification of organic compounds in aerosol samples represents a demanding analytical challenge. In this regard, comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry (GC×GC-TOFMS) has become an effective analytical method. However, verification and validation approaches to quantify these analytes have not been critically evaluated. We compared the performance of gas chromatography with quadrupole mass spectrometry (GC-qMS) and GC×GC-TOFMS for quantitative analysis of eighteen target polycyclic aromatic hydrocarbons (PAHs). The quantitative obtained results such as limits of detection (LODs), limits of quantification (LOQs), and recoveries of target PAHs were approximately equivalent based on both analytical methods. Furthermore, a larger number of analytes were consistently identified from the aerosol samples by GC×GC-TOFMS compared to GC-qMS. Our findings suggest that GC×GC-TOFMS would be widely applicable to the atmospheric and related sciences with simultaneous target and nontarget analysis in a single run.

Optimization and Validation of Thermal Desorption Gas Chromatography-Mass Spectrometry for the Determination of Polycyclic Aromatic Hydrocarbons in Ambient Air

Thermal desorption (TD) coupled with gas chromatography/mass spectrometry (TD-GC/MS) is a simple alternative that overcomes the main drawbacks of the solvent extraction-based method: long extraction times, high sample manipulation, and large amounts of solvent waste. This work describes the optimization of TD-GC/MS for the measurement of airborne polycyclic aromatic hydrocarbons (PAHs) in particulate phase. The performance of the method was tested by Standard Reference Material (SRM) 1649b urban dust and compared with the conventional method (Soxhlet extraction-GC/MS), showing a better recovery (mean of 97%), precision (mean of 12%), and accuracy (±25%) for the determination of 14 EPA PAHs. Furthermore, other 15 nonpriority PAHs were identified and quantified using their relative response factors (RRFs). Finally, the proposed method was successfully applied for the quantification of PAHs in real 8 h-samples (PM₁₀), demonstrating its capability for determination of these compounds in short-term monitoring.

Determination of Selected Polycyclic Aromatic Compounds in Particulate Matter Samples with Low Mass Loading: An Approach to Test Method Accuracy

A miniaturized analytical procedure to determine selected polycyclic aromatic compounds (PACs) in low mass loadings (<10 mg) of particulate matter (PM) is evaluated. The proposed method is based on a simple sonication/agitation method using small amounts of solvent for extraction. The use of a reduced sample size of particulate matter is often limiting for allowing the quantification of analytes. This also leads to the need for changing analytical procedures and evaluating its performance. The trueness and precision of the proposed method were tested using ambient air samples. Analytical results from the proposed method were compared with those of pressurized liquid and microwave extractions. Selected PACs (polycyclic aromatic hydrocarbons (PAHs) and nitro polycyclic aromatic hydrocarbons (NPAHs)) were determined by liquid chromatography with fluorescence detection (HPLC/FD). Taking results from pressurized liquid extractions as reference values, recovery rates of sonication/agitation method were over 80% for the most abundant PAHs. Recovery rates of selected NPAHs were lower. Enhanced rates were obtained when methanol was used as a modifier. Intermediate precision was estimated by data comparison from two mathematical approaches: normalized difference data and pooled relative deviations. Intermediate precision was in the range of 10–20%. The effectiveness of the proposed method was evaluated in PM aerosol samples collected with very low mass loadings (<0.2 mg) during characterization studies from turbofan engine exhausts.

Ambient PM2.5-bound polycyclic aromatic hydrocarbons (PAHs) in Changhua County, central Taiwan: Seasonal variation, source apportionment and cancer risk assessment

This study investigates PM_2.5-bound PAHs for rural sites (Dacheng and Fangyuan) positioned close to heavy air-polluting industries in Changhua County, central Taiwan. A total of 113 PM_2.5 samples with 22 PAHs collected from 2014 to 2015 were analyzed, and Positive Matrix Factorization (PMF) and diagnostic ratios of PAHs were applied to quantify potential PAH sources. The influences of local and regional sources were also explored using the conditional probability function (CPF) and potential source contribution function (PSCF) with PMF-modeled results, respectively. Annual mean concentrations of total PAHs were 2.91 ± 1.34 and 3.04 ± 1.40 ng/m³ for Dacheng and Fangyuan, respectively, and their corresponding BaP_eq were measured at 0.534 ± 0.255 and 0.563 ± 0.273 ng/m³ in concentration. Seasonal variations with higher PAHs found for the winter than for the spring and summer were observed for both sites. The lifetime excess cancer risk (ECR) from inhalation exposure to PAHs was recorded as 4.7 × 10^-5 overall. Potential sources of PM_2.5-bound PAHs include unburned petroleum and traffic emissions (42%), steel industry and coal combustion (31%), and petroleum and oil burning (27%), and unburned petroleum and traffic emission could contribute the highest ECR (2.4 × 10^-5). The CPF results show that directional apportionment patterns were consistent with the actual locations of local PAH sources. The PSCF results indicate that mainly northeastern regions of China have contributed elevated PM_2.5-bound PAHs from long-range transports.

Polycyclic aromatic hydrocarbons (PAHs) in coastal sediments from urban and industrial areas of Asaluyeh Harbor, Iran: distribution, potential source and ecological risk assessment

The distribution and toxicity levels of 16 EPA priority pollutant polycyclic aromatic hydrocarbons (PAHs) in the sediments of Asaluyeh shore, Iran were investigated. The total concentrations of the PAHs in surface sediments ranged from 1,054 to 17,448 ng/g dry weights with a mean concentration of 8,067 ng/g. The spatial distribution of PAHs showed that PAH levels are much higher in the industrial areas in comparison with urban areas. Based on diagnostic ratios, pyrogenic activities were dominant sources of PAHs pollution in sediments comparing petroleum sources. The toxic equivalent concentrations (TEQ Carc) of PAHs ranged from 172 to 2,235 ng TEQ/g with mean value of 997.9. Toxicity levels were evaluated using sediment quality guidelines (SQGs) and toxic equivalent factors. Samples were collected from industrial and urban stations in Asaluyeh shores. According to SQGs, ΣPAHs concentrations in sediments of urban areas were below the ERL (effects range low), but the industrial samples had ΣPAHs concentrations between ERL and ERM (effects range median). Furthermore, ΣHPAHs (heavy PAHs) and some individual PAHs in some industrial stations exceeded ERM, indicating adverse ecological risk effects frequently occur. Findings demonstrate that the surface sediment from Asaluyeh shore is highly to very highly contaminated with PAHs.

Electrochemical Interrogation of G3-Poly(propylene thiophenoimine) Dendritic Star Polymer in Phenanthrene Sensing

A novel dendritic star-copolymer, generation 3 poly(propylene thiophenoimine) (G3PPT)-co-poly(3-hexylthiophene) (P3HT) star co-polymer on gold electrode (i.e., Au|G3PPT-co-P3HT) was used as a sensor system for the determination of phenanthrene (PHE). The G3PPT-co-P3HT star co-polymer was synthesized via in situ electrochemical co-polymerization of generation 3 poly (propylene thiophenoimine) and poly (3-hexylthiophene) on gold electrode. 1HNMR spectroscopy was used to determine the regioregularity of the polymer composites, whereas Fourier transform infrared spectroscopy and scanning electron microscopy were used to study their structural and morphological properties. Au|G3PPT-co-P3HT in the absence of PHE, exhibited reversible electrochemistry attributable to the oligo (thiophene) 'pendants' of the dendrimer. PHE produced an increase in the voltammetric signals (anodic currents) due to its oxidation on the dendritic material to produce catalytic current, thereby suggesting the suitability of the Au|G3PPT-co-P3HT electrode as a PHE sensor. The electrocatalysis of PHE was made possible by the rigid and planar oligo-P3HT species (formed upon the oxidation of the oligo (thiophene) pendants of the star-copolymer), which allowed the efficient capture (binding) and detection (electrocatalytic oxidation) of PHE molecules.

Progress toward the Quantitative Analysis of PAHs Adsorbed on Soot by Laser Desorption/Laser Ionization/Time-of-Flight Mass Spectrometry

Ex situ analyses of substances extracted from flames provide useful albeit mostly qualitative information on the formation process of soot and on the impact of exhausts on the environment. An experimental setup based on the coupling of laser desorption, laser ionization and time-of-flight mass spectrometry (LD/LI/ToF-MS) is presented in past works as an alternative means to more traditional techniques like gas chromatography (GC) to characterize the polycyclic aromatic hydrocarbons (PAHs) content of soot. In this paper, we go one step further in the understanding of the laser desorption/laser ionization dynamics and propose a combined experimental/simulation approach: we estimate the limit of detection of LD/LI/ToF-MS as low as [0.2, 2.8] fmol per laser pulse and we make quantitative predictions on the concentration of PAHs desorbed from soot. In particular, external calibration with model samples where PAHs are adsorbed on black carbon at known concentrations allows us to link the concentration of PAHs desorbed and detected by photoionization ToF-MS to the concentration of PAHs adsorbed on soot. The comparison of data obtained from the analysis of flame sampled soot with standard commercial GC-MS run in parallel validates the approach and defines limits and potentialities of both techniques.

Photolysis degradation of polyaromatic hydrocarbons (PAHs) on surface sandy soil

Polycyclic aromatic hydrocarbons (PAHs) are potent environmental pollutants, and some of them have been identified as carcinogenic and mutagenic. To advance the knowledge of the environmental fate of PAHs, we systematically investigated the influence of different UV wavelengths irradiation on photolysis of PAHs on sandy soil under tow wavelengths (254 and 306 nm) UV irradiation for six PAHs. In addition, kinetic model and influence of several parameters on PAHs photolysis have been studied. The results obtained indicated that UV radiation with a wavelength of 306 nm was more efficient in the photolysis of the polycyclic aromatic hydrocarbons. Our results showed that fluoranthene (Flt) was the fastest in decomposition, has the greatest value for the coefficient of photolysis (7.4 × 10(-3) h(-1)), and has less half-life, reaching 94 h when using a wavelength of 254 nm. The results indicated that the pyrene (Pyr) was more resistant to photolysis in comparison with indeno(1,2,3-cd) pyrene (IP) and fluoranthene (Flt). The results indicate that photolysis is a successful way to remediate the six studied PAHs compounds.

Analytical method for determining polycyclic aromatic hydrocarbon pollutants using ultrafast liquid chromatography with fluorescence detection and the recent column packed with the new 5 μm Kinetex-C18 core-shell particles

An ultrafast liquid chromatography method with fluorescence detection has been optimized for the determination of 15 polycyclic aromatic hydrocarbons (PAHs) using a recent Kinetex-C18 column (250 mm × 4.6 mm). This column has been recently packed with a new brand of porous shell particles with an average particle size of 5 μm to separate various compounds by liquid chromatography, operating at very low pressure. After optimization of the analytical procedure, the separation of the 15 PAHs in spiked tap water samples was achieved without coeluted products in 21.5 min at 16 °C using an aqueous/acetonitrile mobile phase under gradient concentrations with a very low flow rate (0.7–1.0 mL min−1) and low pressure values (870–1590 psi = 60–110 bar), all of these conditions being interesting from an economic point of view. The synchronization of wavelength time changing and the elution time of each compound was performed to avoid baseline deviation. The validation of the whole of the experimental procedure was conducted taking into consideration the following parameters: calibration curve, linearity, limits of detection and quantification, accuracy, sensitivity, precision, and repeatability of the retention time for each PAH. The proposed analytical procedure presented adequate linearity over a concentration range from 0.025 to 10 μg L−1 with a correlation coefficient better than 0.9980. The repeatability (relative standard deviation in percentage, n = 5) of the retention time for the different PAHs investigated ranged from 0.03% to 0.34% and the limit of detection was under 0.6 μg L−1 for most PAHs (excepted for indeno[1,2,3-c,d]pyrene, limit of detection = 1.71 μg L−1). The intraday and interday precisions were below 4%. The recovery of PAH in spiked tap water samples was variable, ranging from 96% to 109%, with relative standard deviation between 0.2% and 4.8%, depending on PAHs and their concentration levels.

Ambient air levels and health risk assessment of benzo(a)pyrene in atmospheric particulate matter samples from low-polluted areas: application of an optimized microwave extraction and HPLC-FL methodology

A new methodology involving a simple and fast pretreatment of the samples by microwave-assisted extraction and concentration by N2 stream, followed by HPLC with fluorescence detection, was used for determining the concentration of benzo(a)pyrene (BaP) in atmospheric particulate matter (PM10 fraction). Obtained LOD, 1.0 × 10(-3) ng/m(3), was adequate for the analysis of benzo(a)pyrene in the samples, and BaP recovery from PAH in Fine Dust (PM10-like) certified reference material was nearly quantitative (86%). The validated procedure was applied for analyzing 115 PM10 samples collected at different sampling locations in the low-polluted area of Extremadura (Southwest Spain) during a monitoring campaign carried out in 2011-2012. BaP spatial variations and seasonal variability were investigated as well as the influence of meteorological conditions and different air pollutants concentrations. A normalized protocol for health risk assessment was applied to estimate lifetime cancer risk due to BaP inhalation in the sampling areas, finding that around eight inhabitants per million people may develop lung cancer due to the exposition to BaP in atmospheric particulates emitted by the investigated sources.

Monitoring of atmospheric gaseous and particulate polycyclic aromatic hydrocarbons in South African platinum mines utilising portable denuder sampling with analysis by thermal desorption-comprehensive gas chromatography-mass spectrometry

Concentrations of diesel particulate matter and polycyclic aromatic hydrocarbons (PAHs) in platinum mine environments are likely to be higher than in ambient air due to the use of diesel machinery in confined environments. Airborne PAHs may be present in gaseous or particle phases each of which has different human health impacts due to their ultimate fate in the body. Here we report on the simultaneous sampling of both phases of airborne PAHs for the first time in underground platinum mines in South Africa, which was made possible by employing small, portable denuder sampling devices consisting of two polydimethylsiloxane (PDMS) multi-channel traps connected in series separated by a quartz fibre filter, which only require small, battery operated portable personal sampling pumps for air sampling. Thermal desorption coupled with comprehensive gas chromatography-mass spectrometry (TD-GC×GC-TofMS) was used to analyse denuder samples taken in three different platinum mines. The samples from a range of underground environments revealed that PAHs were predominantly found in the gas phase with naphthalene and mono-methylated naphthalene derivatives being detected at the highest concentrations ranging from 0.01 to 18 μg m(-3). The particle bound PAHs were found in the highest concentrations at the idling load haul dump vehicle exhausts with a dominance of fluoranthene and pyrene. Particle associated PAH concentrations ranged from 0.47 to 260 ng m(-3) and included benzo[k]fluoranthene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene. This work highlights the need to characterise both phases in order to assess occupational exposure to PAHs in this challenging sampling environment.

Vapor-phase concentrations of PAHs and their derivatives determined in a large city: correlations with their atmospheric aerosol concentrations

Thirteen PAHs, five nitro-PAHs and two hydroxy-PAHs were determined in 55 vapor-phase samples collected in a suburban area of a large city (Madrid, Spain), from January 2008 to February 2009. The data obtained revealed correlations between the concentrations of these compounds and a series of meteorological factors (e.g., temperature, atmospheric pressure) and physical-chemical factors (e.g., nitrogen and sulfur oxides). As a consequence, seasonal trends were observed in the atmospheric pollutants. A "mean sample" for the 14-month period would contain a total PAH concentration of 13835±1625 pg m(-3) and 122±17 pg m(-3) of nitro-PAHs. When the data were stratified by season, it emerged that a representative sample of the coldest months would contain 18900±2140 pg m(-3) of PAHs and 150±97 pg m(-3) of nitro-PAHs, while in an average sample collected in the warmest months, these values drop to 9293±1178 pg m(-3) for the PAHs and to 97±13 pg m(-3) for the nitro-PAHs. Total vapor phase concentrations of PAHs were one order of magnitude higher than concentrations detected in atmospheric aerosol samples collected on the same dates. Total nitro-PAH concentrations were comparable to their aerosol concentrations whereas vapor phase OH-PAHs were below their limits of the detection, indicating these were trapped in airborne particles.

Cancer risk assessments of Hong Kong soils contaminated by polycyclic aromatic hydrocarbons

The aim of this study was to evaluate soils from 12 different land use types on human cancer risks, with the main focus being on human cancer risks related to polycyclic aromatic hydrocarbons (PAHs). Fifty-five locations were selected to represent 12 different types of land use (electronic waste dismantling workshop (EW (DW)); open burning site (OBS); car dismantling workshop (CDW) etc.). The total concentrations of 16 PAHs in terms of total burden and their bioaccessibility were analysed using GC/MS. The PAHs concentrations were subsequently used to establish cancer risks in humans via three exposure pathways, namely, accident ingestion of soil, dermal contact soil and inhalation of soil particles. When the 95th centile values of total PAH concentrations were used to derive ingestion and dermal cancer risk probabilities on humans, the CDW land use type indicated a moderate potential for cancerous development (244 × 10(-6) and 209 × 10(-6), respectively). Bioaccessible PAHs content in soil samples from CDW (3.60 × 10(-6)) were also classified as low cancer risk. CDW soil possessed a higher carcinogenic risk based on PAH concentrations. Bioremediation is recommended to treat the contaminated soil.

Photolysis of polycyclic aromatic hydrocarbons on soil surfaces under UV irradiation

Photolysis of some polycyclic aromatic hydrocarbons (PAHs) on soil surfaces may play an important role in the fate of PAHs in the environment. Photolysis of PAHs on soil surfaces under UV irradiation was investigated. The effects of oxygen, irradiation intensity and soil moisture on the degradation of the three PAHs were observed. The results showed that oxygen, soil moisture and irradiation intensity enhanced the photolysis of the three PAHs on soil surfaces. The degradation of the three PAHs on soil surfaces is related to their absorption spectra and the oxidation-half-wave potential. The photolysis of PAHs on soil surfaces in the presence of oxygen followed pseudo first-order kinetics. The photolysis half-lives ranged from 37.87 days for benzo[a]pyrene to 58.73 days for phenanthrene. The results indicate that photolysis is a successful way to remediate PAHs-contaminated soils.

Sampling and analytical methods for assessing the levels of organic pollutants in the atmosphere: PAH, phthalates and psychotropic substances: a short review

This short review presents the procedures used to monitor PAHs, phthalates and psychotropic substances in the air, and the results of some measurements made in Italy and abroad. Organic contaminants are characterized by a variety of physical and chemical properties, including aggregation phase, concentration level, and life time. This variety widens the spectrum of procedures developed to assess their occurrence in the environment and biota, but prevents the complete speciation of the "organic fraction" of air, waters and particulates, and attention is paid to a few substances. The progress in health sciences stimulates the concern on contaminants and the development of new instrumental apparatuses and methods; new chemicals are continuously identified or recognized as capable of injuring the environment and organisms. Persistent organic pollutants and persistent biologically active toxicants are subject to regulation and extensively measured by means of standard procedures. For instance, polycyclic aromatic hydrocarbons, polychlorobiphenyls and polychlorodibenzodioxins are recovered from air through phase partition, thermal desorption or solvent extraction, then separated and detected through GC-MS or HPLC-MS procedures. By contrast, dedicated methods must be still optimized to monitor candidates or possible candidates as emerging organic pollutants, e.g. phthalates, flame retardants and perfluoroalkanes. Also, psychotropic substances appear of potential concern. Legal and illicit substances are commonly detected in the urban air besides waste and surface waters. If nicotine, caffeine and cocaine will result to enough persistence in the air, their monitoring will become an important issue of global chemical watching in the next future.

Effects of road characteristics on distribution and toxicity of polycyclic aromatic hydrocarbons in urban road dust of Ulsan, Korea

Comparisons between concentration, size effect, molecular distribution, and toxicity of polycyclic aromatic hydrocarbons (PAHs) in urban road dust of Ulsan, Korea, were carried out. The road dust was collected at eleven representative urban sites offering unique road characteristics. The road dust was separated into four size categories as follows: 850-2000 microm, 180-850 microm, 75-180 microm and less than 75 microm. PAHs in the categorized road dust were ultrasonically extracted by a mixture of dichloromethane and n-hexane (1:1) for 30 min. Sixteen PAHs were specifically identified by a high performance liquid chromatography method. Pavement type, traffic volume, vehicle speed and surrounding environment of the study roads greatly affected the overall PAH road dust concentration. The molecular distribution of PAHs was strongly affected by vehicle type, surrounding area and pavement type of road. When the road dust particle size decreased, the total concentration of PAHs increased. The existence of coarse asphalt particles due to the abrasion of new asphalt pavement at some sites could increase the total PAH concentration to a size of 180-850 microm. PAHs in road dust were also evaluated for toxicity using the reported toxicity equivalency factors. The toxicity of PAHs in road dust showed a strong correlation to the total PAH concentration (r(2)=0.955). However, the coefficients of determination (r(2)) for the sizes of 850-2000 microm, 180-850 microm, 75-180 microm and less than 75 microm were 0.966, 0.998, 0.707 and 0.514, respectively.

Preliminary feasibility study of benzo(a)pyrene oxidative degradation by Fenton treatment

Polycyclic aromatic hydrocarbons (PAHs) are considered priority compounds due to their toxic and carcinogenic nature. The concern about water contamination and the consequent human exposure has encouraged the development of new methods for PAHs removal. The purpose of this work was to study the feasibility of a degradation process of benzo(a)pyrene (BaP) in aqueous matrices by oxidation with Fenton reagent. A laboratory unit was designed to optimize the factors which may influence the process: pH (3.5 to 6.0), temperature (30 to 70°C), H₂O₂ (20 to 150 mg L⁻¹), Fe²⁺ concentration (2.75 to 5.50 mg L⁻¹), and the initial concentration of the pollutant (10 to 100 μg L⁻¹). The pH did not influence significantly the results in the range studied. An increase in temperature from 30 to 70°C improved the removal efficiency from 90% to 100%. The same effect was observed for ferrous ion concentrations from 2.75 to 5.50 mg L⁻¹ (increase from 78% to 100% removal). The H₂O₂ concentration played a double role during the process: from 20 to 50 mg L⁻¹ an increase in the removal efficiency was achieved, but for higher concentrations (>50 mg L⁻¹) the degradation is lower. This study proved that the degradation of benzo(a)pyrene by Fenton's reagent is a viable process.