Preparation, properties and applications of polypyrroles

Conducting polymer functionalization in search of advanced materials in ionometry: ion-selective electrodes and optodes

Functionalized conducting polymers (FCPs) have recently garnered attention as ion-selective sensor materials, surpassing their intrinsic counterparts due to synergistic effects that lead to enhanced electrochemical and analytical parameters. Following a brief introduction of the fundamental concepts, this article provides a comprehensive review of the recent developments in the application of FCPs in ion-selective electrodes (ISEs) and ion-selective optodes (ISOs), particularly as ion-to-electron transducers, optical transducers, and ion-selective membranes. Utilizing FCPs in these devices offers a promising avenue for detecting and measuring ions in various applications, regardless of the sample nature and composition. Research has focused on functionalizing different conducting polymers, such as polyaniline and polypyrrole, through strategies such as doping and derivatization to alter their hydrophobicity, conductance, redox capacitance, surface area, pH sensitivity, gas and light sensitivity, etc. These modifications aim to enhance performance outcomes, including potential stability/emission signal stability, reproducibility and low detection limits. The advancements have led to the transition of ISEs from conventional zero-current potentiometric ion sensing to innovative current-triggered sensing approaches, enabling calibration-free applications and emerging concepts such as opto-electro dual sensing systems. The intrinsic pH cross-response and instability of the optical signal of ISOs have been overcome through the novel optical signal transduction mechanisms facilitated by FCPs. In this review, the characteristics of materials, functionalization approaches, particular implementation strategies, specific performance outcomes and challenges faced are discussed. Consolidating dispersed information in the field, the in-depth analysis presented here is poised to drive further innovations by broadening the scope of ion-selective sensors in real-world scenarios.

Advancing Cardiomyocyte Maturation: Current Strategies and Promising Conductive Polymer-Based Approaches

Cardiovascular diseases are a leading cause of mortality and pose a significant burden on healthcare systems worldwide. Despite remarkable progress in medical research, the development of effective cardiovascular drugs has been hindered by high failure rates and escalating costs. One contributing factor is the limited availability of mature cardiomyocytes (CMs) for accurate disease modeling and drug screening. Human induced pluripotent stem cell-derived CMs offer a promising source of CMs; however, their immature phenotype presents challenges in translational applications. This review focuses on the road to achieving mature CMs by summarizing the major differences between immature and mature CMs, discussing the importance of adult-like CMs for drug discovery, highlighting the limitations of current strategies, and exploring potential solutions using electro-mechano active polymer-based scaffolds based on conductive polymers. However, critical considerations such as the trade-off between 3D systems and nutrient exchange, biocompatibility, degradation, cell adhesion, longevity, and integration into wider systems must be carefully evaluated. Continued advancements in these areas will contribute to a better understanding of cardiac diseases, improved drug discovery, and the development of personalized treatment strategies for patients with cardiovascular disorders.

Access to 2,4-Disubstituted Pyrrole-Based Polymer with Long-Wavelength and Stimuli-Responsive Properties via Copper-Catalyzed [3+2] Polycycloaddition

Pyrrole-based polymers (PBPs), a type of fascinating functional polymers, play a crucial role in materials science. However, efficient synthetic strategies of PBPs with diverse structures are mainly focused on conjugated polypyrroles and still remain challenging. Herein, an atom and step economy protocol is described to access various 2,4-disubstituted PBPs by in situ formation of pyrrole core structure via copper-catalyzed [3+2] polycycloaddition of dialkynones and diisocyanoacetates. A series of PBPs is prepared with high molecular weight (Mw up to 18 200 Da) and moderate to good yield (up to 87%), which possesses a fluorescent emission located in the green to yellow light region. Blending the PBPs with polyvinyl alcohol, the stretchable composite films exhibit a significant strengthening of the mechanical properties (tensile stress up to 59 MPa, elongation at break >400%) and an unprecedented stress-responsive luminescence enhancement that over fourfold fluorescent emission intensity is maintained upon stretching up to 100%. On the basis of computational studies, the unique photophysical and mechanical properties are attributed to the substitution of carbonyl chromophores on the pyrrole unit.

Advances in electroactive bioscaffolds for repairing spinal cord injury

Spinal cord injury (SCI) is a devastating neurological disorder, leading to loss of motor or somatosensory function, which is the most challenging worldwide medical problem. Re-establishment of intact neural circuits is the basis of spinal cord regeneration. Considering the crucial role of electrical signals in the nervous system, electroactive bioscaffolds have been widely developed for SCI repair. They can produce conductive pathways and a pro-regenerative microenvironment at the lesion site similar to that of the natural spinal cord, leading to neuronal regeneration and axonal growth, and functionally reactivating the damaged neural circuits. In this review, we first demonstrate the pathophysiological characteristics induced by SCI. Then, the crucial role of electrical signals in SCI repair is introduced. Based on a comprehensive analysis of these characteristics, recent advances in the electroactive bioscaffolds for SCI repair are summarized, focusing on both the conductive bioscaffolds and piezoelectric bioscaffolds, used independently or in combination with external electronic stimulation. Finally, thoughts on challenges and opportunities that may shape the future of bioscaffolds in SCI repair are concluded.

Unusual 3,4-Oxidative Coupling Polymerization on 1,2,5-Trisubstituted Pyrroles for Novel Porous Organic Polymers

Porous organic polymers (POPs) have demonstrated promising task-specific applications due to their structure designability and thus functionality. Herein, an unusual 3,4-polymerization on 1,2,5-trisubstituted pyrroles has been developed to give linear polypyrrole-3,4 in high efficiency, with Mn of 20000 and PDI of 1.7. This novel polymerization technique was applied to prepare a series of polypyrrole-based POPs (PY-POP-1-4), which exhibited high BET surface areas (up to 762 m2 g-1) with a meso-micro-supermicro hierarchically porous structure. Furthermore, PY-POPs were doped in the mixed matrix membranes based on the polysulfone matrix to enhance the gas permeability and gas pair selectivity, with H2/N2 selectivity up to 84.6 and CO2/CH4 and CO2/N2 selectivity up to 46.8 and 39.6.

Polypyrrole-based nanocomposites doped with both salicylate/molybdate and graphene oxide for enhanced corrosion resistance on low-carbon steel

In this work, polypyrrole-based nanocomposites doped with graphene oxide, molybdate, and salicylate (PPy/GO/Mo/Sal) were synthesized via in situ electrochemical polymerization to enhance the anti-corrosion protection performance of polymer coatings. The morphology and structures of the coatings were characterized by SEM, EDX, FTIR, Raman spectroscopy, and XRD. The protection abilities of coatings against corrosion were investigated in 0.1 M NaCl solution with EIS potentiodynamic polarization, salt spray test, and open-circuit potential (OCP) measurements. The results showed that with the presence of both molybdate/salicylate and GO in the PPy matrix, the nanocomposite coating exhibited an excellent protection ability against corrosion for low-carbon steel, better than that with only GO as filler. Compared to the nanocomposites doped with only salicylate or salicylate/GO, the one doped with both molybdate/salicylate and GO exhibited the longest protection plateau (ca. 100 h) on the OCP-time curves with some fluctuation points known as the self-healing action of molybdate dopant. It also resulted in a decrease in the corrosion current (Tafel plots), a higher impedance (Bode plot), and a better protection performance in salt spray tests. In this case, the anti-corrosion ability of the coatings was provided through a barrier and self-healing mechanism.

Tubular Polypyrrole with Chloride Ion Dopants as an Ultrafast Organic Anode for High-Power Lithium-Ion Batteries

Polypyrrole (PPy), as a representative p-type conductive polymer, attracts wide attention for energy storage materials. However, the sluggish reaction kinetics and low specific capacity of PPy impede its application in high-power lithium-ion batteries (LIBs). Herein, tubular PPy with chloride and methyl orange (MO) anionic dopants is synthesized and investigated as an anode for LIBs. The Cl^- and MO anionic dopants can increase the ordered aggregation and the conjugation length of pyrrolic chains, forming plentiful conductive domains and affecting the conduction channel inside the pyrrolic matrix, thereby achieving fast charge transfer and Li⁺ ion diffusion, low ion transfer energy barriers, and rapid reaction kinetics. On account of the above synergistic effect, PPy electrodes deliver a high specific capacity of 2067.8 mAh g^-1 at 200 mA g^-1 and a remarkable rate capacity of 1026 mAh g^-1 at 10 A g^-1 , realizing high energy density (724 Wh kg^-1 ) and power density (7237 W kg^-1 ) simultaneously.

TM-Free and TM-Catalyzed Mechanosynthesis of Functional Polymers

Mechanochemically induced methods are commonly used for the depolymerization of polymers, including plastic and agricultural wastes. So far, these methods have rarely been used for polymer synthesis. Compared to conventional polymerization in solutions, mechanochemical polymerization offers numerous advantages such as less or no solvent consumption, the accessibility of novel structures, the inclusion of co-polymers and post-modified polymers, and, most importantly, the avoidance of problems posed by low monomer/oligomer solubility and fast precipitation during polymerization. Consequently, the development of new functional polymers and materials, including those based on mechanochemically synthesized polymers, has drawn much interest, particularly from the perspective of green chemistry. In this review, we tried to highlight the most representative examples of transition-metal (TM)-free and TM-catalyzed mechanosynthesis of some functional polymers, such as semiconductive polymers, porous polymeric materials, sensory materials, materials for photovoltaics, etc.

Asymmetric Monomer Design Enables Structural Control of M(Salen)-Type Polymers

Conductive and electrochemically active polymers consisting of Salen-type metal complexes as building blocks are of interest for energy storage and conversion applications. Asymmetric monomer design is a powerful tool for fine-tuning the practical properties of conductive electrochemically active polymers but has never been employed for polymers of M(Salen)]. In this work, we synthesize a series of novel conducting polymers composed of a nonsymmetrical electropolymerizable copper Salen-type complex (Cu(3-MeOSal-Sal)en). We show that asymmetrical monomer design provides easy control of the coupling site via polymerization potential control. With in-situ electrochemical methods such as UV-vis-NIR (ultraviolet-visible-near infrared) spectroscopy, EQCM (electrochemical quartz crystal microbalance), and electrochemical conductivity measurements, we elucidate how the properties of these polymers are defined by chain length, order, and cross-linking. We found that the highest conductivity in the series has a polymer with the shortest chain length, which emphasizes the importance of intermolecular iterations in polymers of [M(Salen)].

A Review of MnO2 Composites Incorporated with Conductive Materials for Energy Storage

Manganese dioxide (MnO₂ ) has been widely used in the field of energy storage due to its high specific capacitance, low cost, natural abundance, and being environmentally friendly. However, suffering from poor electrical conductivity and high dissolvability, the performance of MnO₂ can no longer meet the needs of rapidly growing technological development, especially for the application as electrode material in metal-ion batteries and supercapacitors. In this review, recent studies on the development of binary or multiple MnO₂ -based composites with conductive components for energy storage are summarized. Firstly, general preparing methods for MnO₂ -based composites are introduced. Subsequently, the binary and multiple MnO₂ -based composites with carbon, conducting polymer, and other conductive materials are discussed respectively. The improvement in their performance is summarized as well. Finally, perspectives on the practical applications of MnO₂ -based composites are presented.

Electrical Stimulation Increases Axonal Growth from Dorsal Root Ganglia Co-Cultured with Schwann Cells in Highly Aligned PLA-PPy-Au Microfiber Substrates

Nerve regeneration is a slow process that needs to be guided for distances greater than 5 mm. For this reason, different strategies are being studied to guide axonal growth and accelerate the axonal growth rate. In this study, we employ an electroconductive fibrillar substrate that is able to topographically guide axonal growth while accelerating the axonal growth rate when subjected to an exogenous electric field. Dorsal root ganglia were seeded in co-culture with Schwann cells on a substrate of polylactic acid microfibers coated with the electroconductive polymer polypyrrole, adding gold microfibers to increase its electrical conductivity. The substrate is capable of guiding axonal growth in a highly aligned manner and, when subjected to an electrical stimulation, an improvement in axonal growth is observed. As a result, an increase in the maximum length of the axons of 19.2% and an increase in the area occupied by the axons of 40% were obtained. In addition, an upregulation of the genes related to axon guidance, axogenesis, Schwann cells, proliferation and neurotrophins was observed for the electrically stimulated group. Therefore, our device is a good candidate for nerve regeneration therapies.

Evolution of the Surface Structure and Functional Properties of the Electroconducting Polymer Coatings onto Porous Films

Composite systems containing electroconducting polymer coatings (polyaniline and polypyrrole) applied to porous films of semicrystalline polymers (polyethylene, polypropylene, and polyvinylidene fluoride) have been prepared. Porous supports were obtained in the process based on polymer melt extrusion with subsequent annealing, uniaxial extensions, and thermal stabilization. Conducting coatings were formed by the oxidative polymerization of the monomers directly onto the porous supports. The structure (overall porosity, permeability, pore sizes, factor of orientation) and morphology (specific surface and character of the film surface) of the supports were characterized by sorptometry, filtration porosimetry, atomic force microscopy (AFM), and X-ray scattering techniques. It was observed that the porous supports have a strongly developed relief surface which is formed in the pore formation process. It was proven by scanning electron microscopy (SEM) that the porous supports have an oriented structure, and the surface of the composites is defined by the morphology inherent in the conducting component. It was shown that these composites (porous support/conducting coating) demonstrate electric conductivity both along the surface and between surfaces. It was demonstrated that the deposition of conducting coatings leads to an increase in the water wettability of the composites compared with pronounced hydrophobic supports. The composites are characterized by good adhesion between components due to a relief film surface as well as high mechanical strength and elasticity provided by the oriented character of the supports.

A Hyaluronic Acid Demilune Scaffold and Polypyrrole-Coated Fibers Carrying Embedded Human Neural Precursor Cells and Curcumin for Surface Capping of Spinal Cord Injuries

Tissue engineering, including cell transplantation and the application of biomaterials and bioactive molecules, represents a promising approach for regeneration following spinal cord injury (SCI). We designed a combinatorial tissue-engineered approach for the minimally invasive treatment of SCI-a hyaluronic acid (HA)-based scaffold containing polypyrrole-coated fibers (PPY) combined with the RAD16-I self-assembling peptide hydrogel (Corning® PuraMatrix™ peptide hydrogel (PM)), human induced neural progenitor cells (iNPCs), and a nanoconjugated form of curcumin (CURC). In vitro cultures demonstrated that PM preserves iNPC viability and the addition of CURC reduces apoptosis and enhances the outgrowth of Nestin-positive neurites from iNPCs, compared to non-embedded iNPCs. The treatment of spinal cord organotypic cultures also demonstrated that CURC enhances cell migration and prompts a neuron-like morphology of embedded iNPCs implanted over the tissue slices. Following sub-acute SCI by traumatic contusion in rats, the implantation of PM-embedded iNPCs and CURC with PPY fibers supported a significant increase in neuro-preservation (as measured by greater βIII-tubulin staining of neuronal fibers) and decrease in the injured area (as measured by the lack of GFAP staining). This combination therapy also restricted platelet-derived growth factor expression, indicating a reduction in fibrotic pericyte invasion. Overall, these findings support PM-embedded iNPCs with CURC placed within an HA demilune scaffold containing PPY fibers as a minimally invasive combination-based alternative to cell transplantation alone.

Inkjet Printing of Polypyrrole Electroconductive Layers Based on Direct Inks Freezing and Their Use in Textile Solid-State Supercapacitors

In this work, we propose a novel method for the preparation of polypyrrole (PPy) layers on textile fabrics using a reactive inkjet printing technique with direct freezing of inks under varying temperature up to -16 °C. It was found that the surface resistance of PPy layers on polypropylene (PP) fabric, used as a standard support, linearly decreased from 6335 Ω/sq. to 792 Ω/sq. with the decrease of polymerization temperature from 23 °C to 0 °C. The lowest surface resistance (584 Ω/sq.) of PPy layer was obtained at -12 °C. The spectroscopic studies showed that the degree of the PPy oxidation as well as its conformation is practically independent of the polymerization temperature. Thus, observed tendences in electrical conductivity were assigned to change in PPy layer morphology, as it is significantly influenced by the reaction temperature: the lower the polymerization temperature the smoother the surface of PPy layer. The as-coated PPy layers on PP textile substrates were further assembled as the electrodes in symmetric all-solid-state supercapacitor devices to access their electrochemical performance. The electrochemical results demonstrate that the symmetric supercapacitor device made with the PPy prepared at -12 °C, showed the highest specific capacitance of 72.3 F/g at a current density of 0.6 A/g, and delivers an energy density of 6.12 Wh/kg with a corresponding power density of 139 W/kg.

Influence of early thermal-oxidative ageing on the structure and properties of polyoxymethylene copolymer

Thermal-oxidative ageing of polyoxymethylene (POM) copolymer in the oven at 100°C for 1, 2, 3, 5, 7, 10, 14 and 21 days and the influence of early thermal-oxidative ageing on POM structure and properties were studied by means of wide-angle X-ray diffraction, Fourier transform infrared spectroscopy, differential scanning calorimetry and tensile test. Based on the results, we found that the early thermal-oxidative ageing of POM copolymer can be divided into three regions. The region I is the initial 3 days. In this region, some molecular chains rearranged, resulting in internal stress relaxation, increase of crystallinity degree and grain size due to the perfection of crystal structure; both extended chain crystal (ECC) and folded chain crystal (FCC) increased and ECC grew faster than FCC. The region II is from 3 days to 10 days, and in this region, chain scission took place in amorphous region and led to chemi-crystallization. The region III is after 10 days. In this region, the structure and performance of POM copolymer reached a stable situation at this stage. In this work, the difference between skin and core were also analysed.

High performance polypyrrole/SWCNTs composite film as a promising organic thermoelectric material

Conducting polymer thermoelectric (TE) materials have received great attention due to their unique properties. In this work, polypyrrole (PPy)/single-walled carbon nanotubes (SWCNTs) composite films with improved TE performance have been prepared by chemical interfacial polymerization at the cyclohexane/water interface under a controlled temperature. Attributed to the smooth surface, higher conjugation length and more ordered molecular structure of the interfacial polymerized PPy film, the electrical conductivity can be as high as ∼500 S cm⁻¹. To further enhance the TE properties of PPy, SWCNT was added to construct a PPy/SWCNTs composite. Due to the synergistic effect between the two phases and the energy filtering effect at the interfaces between PPy and SWCNTs, the Seebeck coefficient of the composite enhanced significantly with the increase SWCNTs content. The composite shows an optimal power factor of 37.6 ± 2.3 μW mK⁻² when the content of SWCNTs is 0.8 mg. This value is one of the largest values among the reported PPy based composites fabricated by the chemical polymerization method. The results indicate that interfacial polymerization under a controlled temperature is a promising way to improve the TE performance of conducting polymer based composite materials.

PPy/SWCNTs composite films with high thermoelectric performance were prepared by chemical interfacial polymerization under a controlled low temperature.

BDNF-Gene Transfected Schwann Cell-Assisted Axonal Extension and Sprouting on New PLA-PPy Microfiber Substrates

The work here reported analyzes the effect of increased efficiency of brain-derived neurotrophic factor (BDNF) production by electroporated Schwann cells (SCs) on the axonal extension in a coculture system on a biomaterial platform that can be of interest for the treatment of injuries of the nervous system, both central and peripheral. Rat SCs are electrotransfected with a plasmid coding for the BDNF protein in order to achieve an increased expression and release of this protein into the culture medium of the cells, performing the best balance between the level of transfection and the number of living cells. Gene-transfected SCs show an about 100-fold increase in the release of BDNF into the culture medium, compared to nonelectroporated SCs. Cocultivation of electroporated SCs with rat dorsal root ganglia (DRG) is performed on highly aligned substrates of polylactic acid (PLA) microfibers coated with the electroconductive polymer polypyrrol (PPy). The coculture of DRG with electrotransfected SCs increase both the axonal extension and the axonal sprouting from DRG neurons compared to the coculture of DRG with nonelectroporated SCs. Therefore, the use of PLA-PPy highly aligned microfiber substrates preseeded with electrotransfected SCs with an increased BDNF secretion is capable of both guiding and accelerating axonal growth.

Electrothermal Modeling and Analysis of Polypyrrole-Coated Wearable E-Textiles

The inhomogeneity of the resistance of conducting polypyrrole-coated nylon-Lycra and polyester (PET) fabrics and its effects on surface temperature were investigated through a systematic experimental and numerical work including the optimization of coating conditions to determine the lowest resistivity conductive fabrics and establish a correlation between the fabrication conditions and the efficiency and uniformity of Joule heating in conductive textiles. For this purpose, the effects of plasma pre-treatment and molar concentration analysis of the dopant anthraquinone sulfonic acid (AQSA), oxidant ferric chloride, and monomer pyrrole was carried out to establish the conditions to determine the sample with the lowest electrical resistance for generating heat and model the experiments using the finite element modeling (FEM). Both PET and nylon-Lycra underwent atmospheric plasma treatment to functionalize the fabric surface to improve the binding of the polymer and obtain coatings with reduced resistance. Both fabrics were compared in terms of average electrical resistance for both plasma treated and untreated samples. The plasma treatment induced deep black coatings with lower resistance. Then, heat-generating experiments were conducted on the polypyrrole (PPy) coated fabrics with the lowest resistance using a variable power supply to study the distribution and maximum value of the temperature. The joule heating model was developed to predict the heating of the conductive fabrics via finite element analysis. The model was based on the measured electrical resistance at different zones of the coated fabrics. It was shown that, when the fabric was backed with neoprene insulation, it would heat up quicker and more evenly. The average electrical resistance of the PPy-PET sample used was 190 Ω, and a maximum temperature reading of 43 °C was recorded. The model results exhibited good agreement with thermal camera data.

Gamma rays as an innovative tool for synthesizing conducting copolymers with improved properties

Radiation chemistry was used as an alternative methodology for synthesizing conducting copolymers in water and dichloromethane.

One-step synthesis of well-dispersed polypyrrole copolymers under gamma-ray irradiation

Herein, we report for the first time the synthesis of polypyrrole copolymers with good solvent-dispersibility under gamma-ray irradiation at room temperature in air.

Experimental Study and Mathematical Modeling of a Glyphosate Impedimetric Microsensor Based on Molecularly Imprinted Chitosan Film

A novel impedimetric microsensor based on a double-layered imprinted polymer film has been constructed for the sensitive detection of the herbicide, glyphosate (GLY), in water. It is based on electropolymerized polypyrrole films, doped with cobaltabis(dicarbollide) ions ([3,3′-Co(1,2-C2B9H11)2]), as a solid contact layer between the gold microelectrode surface and the molecularly imprinted chitosan film (CS-MIPs/PPy/Au). Electrochemical Impedance Spectroscopy (EIS) was used for the characterization of the CS-molecular imprinted polymers (MIPs)/PPy/Au in the presence of GLY concentrations between 0.31 pg/mL and 50 ng/mL. Experimental responses of CS-MIPs/PPy/Au are modeled for the first time using an exact mathematical model based on physical theories. From the developed model, it was possible to define the optimal range of the parameters that will impact the quality of impedance spectra and then the analytical performance of the obtained microsensor. The obtained microsensor shows a low detection limit of 1 fg/mL (S/N = 3), a good selectivity, a good reproducibility, and it is regenerable.

One-Step Synthesis of Polypyrrole-Coated Gold Nanoparticles for Use as a Photothermally Active Nano-System

OBJECTIVE

This paper introduces a simple one-step and ultra-fast method for synthesis of highly photothermally active polypyrrole-coated gold nanoparticles. The synthesis process is so simple that the reaction is very fast without the need for any additives or complicated steps.

METHODOLOGY

Polypyrrole-coated gold nanoparticles (AuPpy NPs) were synthesized by reacting chloroauric acid (HAuCl4) with pyrrole (monomer) in aqueous medium at room temperature. These nanoparticles were characterized by UV-visible-NIR spectrometry, transmission electron microscopy (TEM), AC conductivity, zeta sizer and were evaluated for dark cytotoxicity and photocytotoxicity using human hepatocellular carcinoma (HepG2) cell line as a model for cancer cells.

RESULTS

The synthesized AuPpy NPs showed a peak characteristic for gold nanoparticles (530-600 nm, molar ratio dependent) and a wide absorption band along the visible-NIR region with intensity about triple or even quadruple that of polypyrrole synthesized by the conventional FeCl3 method at the same concentration and under the same conditions. TEM imaging showed that the synthesized AuPpy NPs were composed of spherical or semi-spherical gold core(s) of about 4-10 nm coated with distinct layer(s) of polypyrrole seen either loosely or in clusters. Mean sizes of the synthesized nanoparticles range between ~25 and 220 nm (molar ratio dependent). Zeta potentials of the AuPpy NPs preparations indicate their good colloidal stability. AC conductivity values of AuPpy NPs highly surpass that of Ppy prepared by the conventional FeCl3 method. AuPpy NPs were non-toxic even at high concentrations (up to 1000 µM pyrrole monomer equivalent) under dark conditions. Unlikely, light activated the photothermal activity of AuPpy NPs in a dose-dependent manner.

CONCLUSION

This method simply and successfully synthesized AuPpy NPs nanoparticles that represent a safe alternative photothermally active multifunctional tool instead of highly toxic and non-biodegradable gold nanorods.

MoO3 Nanobelts Embedded Polypyrrole/SIS Copolymer Blends for Improved Electro-Mechanical Dual Applications

This research endeavor aimed to develop thin film blends of polypyrrole (PPy) and poly (styrene-isoprene-styrene) (SIS) with MoO₃ as a nanofiller for improved mechanical and electrical properties to widen its scope in the field of mechatronics. This study reports blends of polypyrrole (PPy) and poly (styrene-isoprene-styrene) (SIS) tri-block copolymer showing improved mechanical and electrical attributes while employing MoO₃ nanobelts as nanofillers that additionally improves the abovementioned properties in the ensuing nanocomposites. The synthesis of PPy/SIS blends and MoO₃/PPy/SIS nanocomposites was well corroborated with XRD, SEM, FTIR, and EDS analysis. Successful blending of PPy was yielded up to 15 w/w% PPy in SIS, as beyond this self-agglomeration of PPy was observed. The results showed a remarkable increase in the conductivity of insulating SIS copolymer from 1.5 × 10^−6.1 to 0.343 Scm⁻¹ and tensile strength up to 8.5 MPa with the 15 w/w% PPy/SIS blend. A further enhancement of the properties was recorded by embedding MoO₃ nanobelts with varying concentrations of the nanofillers into 15 w/w% PPy/SIS blends. The mechanical strength of the polymeric nanocomposites was enhanced up to 11.4 MPa with an increase in conductivity up to 1.51 Scm⁻¹ for 3 w/w% MoO₃/PPy-SIS blends. The resultant product exhibited good potential for electro-mechanical dual applications.

Gold nanoparticle decorated polypyrrole/graphene oxide nanosheets as a modified electrode for simultaneous determination of ascorbic acid, dopamine and uric acid

AuNPs, GO and PPy are combined effectively to form a novel composite showing a huge enhancement in electrochemical performance compared to the single materials.

Electrochromic Self-Electrostabilized Polypyrrole Films Doped with Surfactant and Azo Dye

Two azo dyes, acid red 1 (AR1) and acid red 18 (AR18), were used alone or in combination with sodium dodecyl sulfate (SDS) for the electropolymerization of a pyrrole monomer. Polypyrrole (PPy) showed higher redox capacity when SDS and AR18 were used simultaneously as dopant agents (PPy/AR18-SDS) than when the conducting polymer was produced in the presence of SDS, AR18, AR1, or an AR1/SDS mixture. Moreover, PPy/AR18-SDS is a self-stabilizing material that exhibits increasing electrochemical activity with the number of oxidation–reduction cycles. A mechanism supported by scanning electron microscopy and X-ray diffraction structural observations was proposed to explain the synergy between the SDS surfactant and the AR18 dye. On the other hand, the Bordeaux red color of PPy/AR18-SDS, which exhibits an optical band gap of 1.9 eV, rapidly changed to orange-yellow and blue colors when films were reduced and oxidized, respectively, by applying linear or step potential ramps. Overall, the results indicate that the synergistic utilization of AR18 and SDS as dopant agents in the same polymerization reaction is a very successful and advantageous strategy for the preparation of PPy films with cutting-edge electrochemical and electrochromic properties.

One-Dimensional Nanostructure Engineering of Conducting Polymers for Thermoelectric Applications

The past few decades have witnessed considerable progress of conducting polymer-based organic thermoelectric materials due to their significant advantages over the traditional inorganic materials. The nanostructure engineering and performance investigation of these conducting polymers for thermoelectric applications have received considerable interest but have not been well documented. This review gives an outline of the synthesis of various one-dimensional (1D) structured conducting polymers as well as the strategies for hybridization with other nanomaterials or polymers. The thermoelectric performance enhancement of these materials in association with the unique morphologies and structures are discussed. Finally, perspectives and suggestions for the future research based on these interesting nanostructuring methodologies for improvement of thermoelectric materials are also presented.

On-Chip Electrochemical Detection of Cholera Using a Polypyrrole-Functionalized Dendritic Gold Sensor

Rapid diagnosis of an infectious disease outbreak in the field is critical for limiting the escalation of an outbreak into an epidemic. Devices suited to point-of-care (POC) diagnosis of cholera must not only demonstrate clinical laboratory levels of sensitivity and specificity but do so in a portable and low-cost manner, with a simplistic readout. We report work toward an on-chip electrochemical immunosensor for the detection of cholera toxin subunit B (CTX), based on a dendritic gold architecture biofunctionalized via poly(2-cyanoethyl)pyrrole (PCEPy). The dendritic electrode has an ∼18× greater surface area than a planar gold counterpart, per electrochemical measurements, allowing for a higher level of detection sensitivity. A layer of PCEPy polymer generated on the dendritic surface facilitated the performance of an electrochemical enzyme-linked immunosorbant assay (ELISA) for CTX on-chip, which demonstrated a detection limit of 1 ng mL^-1, per a signal-to-noise ratio of 2.6. This was more sensitive than detection using a simple planar gold electrode (100 ng mL^-1) and also matched the diagnostic standard optical ELISA, but on a miniaturized platform with electrical readout. The ability to meet POC demands makes biofunctionalized gold dendrites a promising architecture for on-chip detection of cholera.