Lysine-Promoted Colorimetric Response of Gold Nanoparticles: A Simple Assay for Ultrasensitive Mercury(II) Detection

Sensitive visual detection of norfloxacin in water by smartphone assisted colorimetric method based on peroxidase-like active cobalt-doped Fe3O4 nanozyme

Norfloxacin is widely used owing to its strong bactericidal effect on Gram-negative bacteria. However, the residual norfloxacin in the environment can be biomagnified via food chain and may damage the human liver and delay the bone development of minors. Present work described a reliable and sensitive smartphone colorimetric sensing system based on cobalt-doped Fe3O4 magnetic nanoparticles (Co-Fe3O4 MNPs) for the visual detection of norfloxacin. Compared with Fe3O4, Co-Fe3O4 MNPs earned more remarkably peroxidase-like activity and TMB (colorless) was rapidly oxidized to oxTMB (blue) with the presence of H2O2. Interestingly, the addition of low concentration of norfloxacin can accelerate the color reaction process of TMB, and blue deepening of the solution can be observed with the naked eye. However, after adding high concentration of norfloxacin, the activity of nanozyme was inhibited, resulting in the gradual fading of the solution. Based on this principle, a colorimetric sensor integrated with smartphone RGB mode was established. The visual sensor exhibited good linearity for norfloxacin monitoring in the range of 0.13-2.51 µmol/L and 17.5-100 µmol/L. The limit of visual detection was 0.08 µmol/L. In the actual water sample analysis, the spiked recoveries of norfloxacin were over the range of 95.7%-104.7 %. These results demonstrated that the visual sensor was a convenient and fast method for the efficient and accurate detection of norfloxacin in water, which may have broad application prospect.

A portable solid sampling visualization nano-sensor for soil Cd based on "three-phase transforming" technique

Direct analysis of solid samples is always challenging for ionic sensors due to solidified elemental presence and matrix interference. In this work, a "three-phase transforming" technique was first established to make solid sampling elemental sensors and visual detection possible in the future. For Cd transforming from soil samples, a metal ceramic heater (MCH) electrothermal vaporizer (ETV) coupled with a dielectric barrier discharge quartz trap (DBD-QT) was first utilized to fulfill the solid sampling and preconcentration of Cd in soil; for on-site analysis, a colorimetric sensor based on the trithiocyanuric acid (TMT) functionalized gold nanoparticles (AuNPs) was chosen as a chromogenic analysis model. The portable and miniature ETV-DBD apparatus directly introduced Cd from soil and then captured Cd, consuming only <130 W and 4.5 kg weight; finally, only 200 μL water was injected as eluent to dissolve Cd for the following colorimetric detection. Herein, the Cd analyte underwent a "three-phase transforming" from solid (Cd compounds in soil), to aerosol (vaporization and transportation), to solid (Cd oxides trapped on quartz surface) and to liquid (Cd2+ in eluate). Under optimized conditions, the method limit of detection (LOD) reached 0.04 mg/kg Cd (50 mg sample), fulfilling fast monitoring of Cd contamination in soil, with <20 % relative standard deviations (RSDs). The analysis time was <10 min excluding sample digestion and acid application, as well as the interference of Pb2+ on the AuNPs sensor can be eliminated via the "three-phase transforming" process, proving an excellent anti-interference for solid analysis. This "three-phase transforming" processing technique coupled with colorimetric sensor holds a great potential for direct and on-site analysis in solid samples without complicated handling, providing a fantastic methodology for the application of ionic sensors and making solid sampling elemental sensor and visual detection possible.

Colorimetric detection of the potent carcinogen aflatoxin B1 based on the aggregation of L-lysine-functionalized gold nanoparticles in the presence of copper ions

L-lysine functionalized gold nanoparticles (AuNPs-Lys) have been widely used for the detection of worldwide interest analytes. In this work, a colorimetric assay for the detection of the carcinogen aflatoxin B1 (AFB1) based on the aggregation of AuNPs-Lys in the presence of copper ions was developed. For this purpose, AuNPs were synthesized in citrate aqueous solution, functionalized, and further characterized by UV-Vis, fluorescence, Fourier transform infrared spectroscopy (FTIR), nanoparticle tracking analysis (NTA), dynamic light scattering (DLS), and transmission electron microscopy (TEM). In general, AuNPS-Lys (~2.73 × 1011 particles) offered a clear colorimetric response in the presence of AFB1 and Cu2+ ions showing linearity in the range of 6.25 to 200 ng AFB1/mL, with a detection limit of 4.18 ng AFB1/mL via photometric inspection. Moreover, the performance of the proposed methodology was tested using the 991.31 AOAC official procedure based on monoclonal antibodies in maize samples artificially contaminated with AFB1. There was a good agreement between the measured AFB1 concentrations in both assays, the average recoveries for the colorimetric and immunoaffinity assays were between 91.2-98.4% and 96.0-99.2%, respectively. These results indicated that the colorimetric assay could be used as a rapid, eco-friendly, and cost-effective platform for the quantification of AFB1 in maize-based products.

Coumarin Derivative and Gold Nanoparticle Conjugate as a Selective Fluorescent Sensor for Mercury Ion in Real Sample

A biphenyl based coumarin fluorescent molecule, N,N'-bis(7-diethylamino-2-oxo-2 H-chromen-3-yl)methylene)biphenyl-2-2'-dicarbohydrazide (molecule 1) has been synthesized and characterised. Photophysical studies of 1 exhibit solvent polarity dependent absorption and emission maxima. Citrate capped gold nanoparticles (AuNPs) have been mixed with molecule 1 for the preparation of AuNPs/1 conjugate. The association constant of the AuNPs/1 conjugate has been calculated to 4.54 × 104 M- 1. The AuNPs/1 conjugate has been found to detect Hg2+ ion selectively by fluorescence enhancement. While addition of molecule 1 into the solution of AuNPs, fluorescence intensity of 1 quenched. On addition of several monovalent, divalent and trivalent metal ion into the solution of AuNPs/1 conjugate separately, there was no change in fluorescence intensity of 1 has been observed. However, upon addition of Hg2+ ion into the solution of AuNPs/1 conjugate, the fluorescence intensity enhancement occurred, indicating released of 1 from the surface of AuNPs and probably aggregation of AuNPs took place in presence of Hg2+ ion. The AuNPs/1 conjugate has been found to have a detection limit of 2.3 × 10- 9 M for Hg2+ ion in aqueous solvent. Meanwhile, the AuNPs/1 conjugate have also been successfully applied for the determination of Hg2+ in real water samples.

A fluorescent probe based on aptamer gold nanoclusters for rapid detection of mercury ions

The mercuric ion (Hg2+) is a hazardous pollutant that is widely distributed in living organisms, foods, and environments with highly toxic and bio-accumulative properties. In the present study, a fluorescent probe based on aptamer gold nanoclusters (apt-AuNCs) was prepared for the ultrasensitive detection of Hg2+ in food. The principle underlying the prepared probe was the quenching of the fluorescence of apt-AuNCs in the presence of Hg2+ due to the strong metallophilic interactions between the 5d10 centers of Hg2+ and Au+. Under optimal conditions, the proposed fluorescent probe exhibited a linear relationship with Hg2+ concentration within the range of 2-200 nM (R2 = 0.9960). In addition, the limit of detection (LOD) was 0.0158 nM, which is below the Chinese standard value of 25 nM for Hg2+ in food. Furthermore, the apt-AuNCs were applied to detect Hg2+ in spinach and crawfish samples, with recovery percentages of 91.99%∼108.06%, meaning that apt-AuNCs could be used as a promising probe to detect Hg2+ in complex food samples.

Synthesis of vancomycin functionalized fluorescent gold nanoparticles and selective sensing of mercury (II)

Mercury ions (Hg2+) are widely found in the environment; it is considered a major pollutant. Therefore, the rapid and reliable detection of Hg2+ is of great technical interest. In this study, a highly fluorescent, sensitive, and selective fluorometric assay for detecting Hg2+ ions was developed using vancomycin functionalized and polyethyleneimine stabilized gold nanoparticles (PEI-f-AuNPs@Van). The as-made gold nanoparticles were highly fluorescent, with excitation and emission maxima occurring at 320 and 418 nm, respectively. The size of nanoparticles was ~7 nm; a zeta potential of ~38.8 mV was determined. The XRD analysis confirmed that the nanoparticles possessed crystalline structure with face centerd cubic symmetry. Using the PEI-f-AuNP@Van probe, the detection limit of Hg2+ ion was achieved up to 0.988 nM (within a linear range) by calculating the KSV. However, the detection limit in a natural environmental sample was shown to be 12.5 nM. Furthermore, the selectivity tests confirmed that the designed probe was highly selective to mercury (II) cations among tested other divalent cations. Owing to its sensitivity and selectivity, this approach for Hg2+ ions detection can be utilized for the analysis of real water samples.

Analyte-triggered in situ “off–on” of Tyndall effect for smartphone-based quantitative nanosensing of Ag+ ions

This work describes two new colorimetric methods for smartphone-based point-of-care nanosensing of toxic Ag⁺ ions. They were based on the analyte-triggered in situ "off-on" of Tyndall effect (TE) of non-plasmonic colloid or plasmonic metal nanoprobes. The first TE-inspired assay (TEA) focused on the initial analytical application of precipitation reactions where a non-plasmonic AgCl colloid could be formed once mixing the analyte with a NaCl solution. Such AgCl colloid displayed strong visual TE signals after their irradiation by a laser pointer pen, which unexpectedly achieved a detection limit of ~ 400 nM. The second TEA was further designed to reduce the limit down to ~ 78 nM using the analyte's oxidizability towards 3,3',5,5'-tetramethylbenzidine molecules. The redox reaction could create positively charged products that could make negatively charged plasmonic gold nanoparticles aggregate through electrostatic interactions to remarkably amplify their TE responses. Both limits were lower than the minimum allowable Ag⁺ level (~ 460 nM) in drinking water issued by the World Health Organization. The satisfactory recovery results for detecting Ag⁺ ions in river, pond, tap, and drinking water additionally demonstrated good selectivity, accuracy and practicality of the proposed methods for potential point-of-need uses in environmental analysis, public health, water safety, etc.

A Critical Review on the Development of Optical Sensors for the Determination of Heavy Metals in Water Samples. The Case of Mercury(II) Ion

Recent publications are reviewed concerning the development of sensors for the determination of mercury in drinking water, based on spectroscopic methodologies. A critical analysis is made of the specific details and figures of merit of the developed protocols. Special emphasis is directed to the validation and applicability to real samples in the usual concentration range of mercury, considering the maximum allowed limits in drinking water established by international regulations. It was found that while most publications describe in detail the synthesis, structure, and physicochemical properties of the sensing phases, they do not follow the state of the art in the analytical developments. Recommendations are provided regarding the proper method development and validation, including the setting of the calibration concentration range, the correct estimation of the limits of detection and quantitation, the concentration levels to be set for producing spiked water samples, the number of real samples for adequate validation, the comparison of the developed method with a reference technique, and other analytical features which should be followed.

Detection and imaging of Hg(II) in vivo using glutathione-functionalized gold nanoparticles

The optical and biological properties of functionalized gold nanoparticles (GNPs) have been widely used in sensing applications. GNPs have a strong binding ability to thiol groups. Furthermore, thiols are used to bind functional molecules, which can then be used, for example, to detect metal ions in solution. Herein, we describe 13 nm GNPs functionalized by glutathione (GSH) and conjugated with a rhodamine 6G derivative (Rh6G2), which can be used to detect Hg(II) in cells. The detection of Hg²⁺ ions is based on an ion-catalyzed hydrolysis of the spirolactam ring of Rh6G2, leading to a significant change in the fluorescence of GNPs-GSH-Rh6G2 from an "OFF" to an "ON" state. This strategy is an effective tool to detect Hg²⁺ ions. In cytotoxicity experiments, GNPs-GSH-Rh6G2 could penetrate living cells and detect mercury ions through the fluorescent "ON" form.

Identification of heavy metal ions from aqueous environment through gold, Silver and Copper Nanoparticles: An excellent colorimetric approach

Heavy metal pollution has become a severe threat to human health and the environment for many years. Their extensive release can severely damage the environment and promote the generation of many harmful diseases of public health concerns. These toxic heavy metals can cause many health problems such as brain damage, kidney failure, immune system disorder, muscle weakness, paralysis of the limbs, cardio complaint, nervous system. For many years, researchers focus on developing specific reliable analytical methods for the determination of heavy metal ions and preventing their acute toxicity to a significant extent. The modern researchers intended to utilize efficient and discerning materials, e.g. nanomaterials, especially the metal nanoparticles to detect heavy metal ions from different real sources rapidly. The metal nanoparticles have been broadly utilized as a sensing material for the colorimetric detection of toxic metal ions. The metal nanoparticles such as Gold (Au), Silver (Ag), and Copper (Cu) exhibited localized plasmon surface resonance (LPSR) properties which adds an outstanding contribution to the colorimetric sensing field. Though, the stability of metal nanoparticles was major issue to be exploited colorimetric sensing of heavy emtal ions, but from last decade different capping and stabilizing agents such as amino acids, vitmains, acids and ploymers were used to functionalize the metal surface of metal nanoparticles. These capping agents prevent the agglomeration of nanoparticles and make them more active for prolong period of time. This review covers a comprehensive work carried out for colorimetric detection of heavy metals based on metal nanoparticles from the year 2014 to onwards.

Achieving Ultrasensitive Point-of-Care Assay for Mercury Ions with a Triple-Mode Strategy Based on the Mercury-Triggered Dual-Enzyme Mimetic Activities of Au/WO3 Hierarchical Hollow Nanoflowers

The exploration of new strategies for portable detection of mercury ions with high sensitivity and selectivity is of great value for biochemical and environmental analyses. Herein, a straightforward, convenient, label-free, and portable sensing platform based on a Au nanoparticle (NP)-decorated WO₃ hollow nanoflower was constructed for the sensitive and selective detection of Hg(II) with a pressure, temperature, and colorimetric triple-signal readout. The resulting Au/WO₃ hollow nanoflowers (Au/WO₃ HNFs) could efficaciously impede the aggregation of Au NPs, thus significantly improving their catalytic activity and stability. The sensing mechanism of this new strategy using pressure as a signal readout was based on the mercury-triggered catalase mimetic activity of Au/WO₃ HNFs. In the presence of the model analyte Hg(II), H₂O₂ in the detection system was decomposed to O₂ fleetly, resulting in a detectable pressure signal. Accordingly, the quantification of Hg(II) was facilely realized based on the pressure changes, and the detection limit could reach as low as 0.224 nM. In addition, colorimetric and photothermal detection of Hg(II) using the Au/WO₃ HNFs based on their mercury-stimulated peroxidase mimetic activity was also investigated, and the detection limits were calculated to be 78 nM and 0.22 μM for colorimetric and photothermal methods, respectively. Hence, this nanosensor can even achieve multimode determination of Hg(II) with the concept of point-of-care testing (POCT). Furthermore, the proposed multimode sensing platform also displayed satisfactory sensing performance for the Hg(II) assay in actual water samples. This promising strategy may provide novel insights on the fabrication of a multimode POCT platform for sensitive, selective, and accurate detection of heavy metal ions.

Gold-Modified Molecularly Imprinted N-Methacryloyl-(l)-phenylalanine-containing Electrodes for Electrochemical Detection of Dopamine

A molecularly imprinted polymer-based pencil graphite electrode (MIP PGE) sensor, modified with gold nanoparticles, was utilized for the detection of dopamine in the presence of other biochemical compounds using cyclic voltammetry (CV) and differential pulse voltammetry (DPV), depending on its strong electroactivity function. The pulse voltammetry methods recorded the highest response. In addition to the high oxidation rate of DA and the other biomolecule interferences available in the sample matrix used, which cause overlapping voltammograms, we aimed to differentiate them in a highly sensitive limit of detection range. The calibration curves for DA were obtained using the CV and DPV over the concentration range of 0.395–3.96 nM in 0.1 M phosphate buffer solution (PBS) at pH 7.4 with a correlation coefficient of 0.996 and a detection limit of 0.193 nM. The electrochemical technique was employed to detect DA molecules quantitatively in human blood plasma selected as real samples without applying any pre-treatment processes. MIP electrodes proved their ability to detect DA with high selectivity, even with epinephrine and norepinephrine competitor molecules and interferences, such as ascorbic acid (AA). The high level of recognition achieved by molecularly imprinted polymers (MIPs) is essential for many biological and pharmaceutical studies.

Tyndall-Effect-inspired assay with gold nanoparticles for the colorimetric discrimination and quantification of mercury ions and glutathione

This work initially reports a new nanosening method for simple, sensitive, specific, visual detection of mercury (II) (Hg²⁺) and glutathione (GSH) using the Tyndall Effect (TE) of the same colloidal gold nanoparticle (GNP) probes for efficient colorimetric signaling amplification. For the TE-inspired assay (TEA) method, arginine (Arg) molecules are pre-modified on the GNPs' surfaces (Arg-GNPs). Upon the Hg²⁺ introduction, it can be specifically coordinated with the terminal -NH₂ and -COOH groups of the Arg molecules to make the Arg-GNPs aggregate, producing a significantly-enhanced TE signal in the reaction solution after its irradiation by a 635-nm red laser pointer pen. On the other hand, the introduction of the GSH results in the production of the original Arg-GNPs' weak TE response, as it is able to bind such metal ion via mercury-thiol reactions to inhibit the above aggregation. Under the optimal conditions, the utility of the new TEA method is well demonstrated to quantitatively detect the Hg²⁺ and GSH with the aid of a smartphone as a portable TE reader during the linear concentration ranges of 50-3000 and 10-3000 nM, respectively. The detection limits for the Hg²⁺ and GSH are estimated to be as low as ∼3.5 and ∼0.3 nM, respectively. The recovery results obtained from the detection of Hg²⁺ in the complex tap and pond water samples and the assay of GSH in real human serum and urine samples are also satisfactory.

Regulation of conjugate rigid plane structures for achieving transformation of fluorescence recognition properties

Regulation of a conjugate rigid plane structure based on bisbenzimidazole derivatives to research the structure-effective relationship between conjugate systems size and fluorescence sensing properties.

A controllable staining colorimetric method based on carboxylated cellulose membranes for early-warning and semi-quantitative detection of aflatoxins in water

A controllable staining colorimetric method was proposed for antibody-free detection of AFs by exploiting controllable electrostatic-staining of CCMs with Hg2+-capped AuNPs.

Fluorescence-active and peroxidase-like expanded mesoporous silica-encapsulated ultrasmall Pt nanoclusters: a novel colorimetric/fluorescent dual-mode nanosensor for sensitive detection of mercury in medicinal and edible Pueraria lobata

A novel colorimetric/fluorescent dual-mode nanosensor for Hg²⁺ detection was constructed using expanded mesoporous silica (EMSN)-encapsulated ultrasmall platinum nanoclusters (EMSN@Pt NCs) with improved peroxidase-like and stable fluorescent activities. The sensing technique was based on the mechanism that the peroxidase mimetic activity and fluorescence intensity of EMSN@Pt NCs can be inhibited in the presence of Hg²⁺. In this sensing platform, a linear range of 5-50 nM with a detection limit of 1.78±0.38 nM and quantification limit of 5.93 nM was obtained via fluorescent analysis. A linear calibration curve from 0.25 to 200 nM with a detection limit of 8.25±0.51 nM and quantification limit of 27.47 nM was achieved via colorimetric analysis. The proposed dual-mode probe possesses excellent selectivity and reliability for Hg²⁺ detection, which can function as an efficient nanosensor for the quantitative determination of Hg²⁺ in Pueraria lobata.

Colorimetric Sensing with Gold Nanoparticles on Electrowetting-Based Digital Microfluidics

Digital microfluidic (DMF) has been a unique tool for manipulating micro-droplets with high flexibility and accuracy. To extend the application of DMF for automatic and in-site detection, it is promising to introduce colorimetric sensing based on gold nanoparticles (AuNPs), which have advantages including high sensitivity, label-free, biocompatibility, and easy surface modification. However, there is still a lack of studies for investigating the movement and stability of AuNPs for in-site detection on the electrowetting-based digital microfluidics. Herein, to demonstrate the ability of DMF for colorimetric sensing with AuNPs, we investigated the electrowetting property of the AuNPs droplets on the hydrophobic interface of the DMF chip and examined the stability of the AuNPs on DMF as well as the influence of evaporation to the colorimetric sensing. As a result, we found that the electrowetting of AuNPs fits to a modified Young–Lippmann equation, which suggests that a higher voltage is required to actuate AuNPs droplets compared with actuating water droplets. Moreover, the stability of AuNPs was maintained during the processing of electrowetting. We also proved that the evaporation of droplets has a limited influence on the detections that last several minutes. Finally, a model experiment for the detection of Hg²⁺ was carried out with similar results to the detections in bulk solution. The proposed method can be further extended to a wide range of AuNPs-based detection for label-free, automatic, and low-cost detection of small molecules, biomarkers, and metal ions.

A functional peptide-mediated colorimetric assay for mercury ion based on dual-modified gold nanoparticles

In the work, a rapid and accurate biosensor for mercury ions (Hg²⁺) was constructed, with which aggregation of dual-modified (DGPFHR- and CALNN-) gold nanoparticles (D/C-AuNPs) could be triggered by the high specificity of peptides to Hg²⁺. The given peptide DGPFHR possesses great capability of capturing Hg²⁺, accompanied by the conformational folding. Under the circumstances, D/C-AuNPs were employed as the detection probes to accomplish the quantitative analysis of Hg²⁺. This is primarily because the specific Hg²⁺-induced folding of peptides reduces the electrostatic repulsion and steric hindrance, thus accelerating the AuNPs aggregation. The principle and application potential of this proposal was proved by evidence. And the results demonstrated that Hg²⁺ ions could be selectively detected as low as 28 nM with a linear range of 100-800 nM. In consideration of superior simplicity, selectivity, accuracy and stability, the protocol was advantageous over other projects in practical measurement of various water samples.

Surface Plasmon Resonance Sensor for Novel Detection of Histidine Based on the Hg2+ Induced Aggregation of AuNPs Followed by Preconcentration with Chitosan Gel as Solid-phase Biosorbent

This research work aims to propose an extraction method using chitosan as the sorbent and gold nanoparticles (AuNPs) as the colorimetric sensor for the development of a simple, cost-effective, rapid, sensitive, and selective detection method for histidine. The colorimetric assay is based on the aggregation of AuNPs in the presence of Hg2+ ions and histidine. The state of AuNPs generally changes from dispersion to aggregation. The change in state is accompanied by a corresponding change in color (from red wine to blue). Therefore, the solid phase extraction (SPE) method using chitosan as the sorbent was used to extract the AuNPs to improve the sensitivity of detection. It was found that the extraction by means of a sensor system using chitosan could increase the detection signal for histidine by 10 times. The calibration curve, which is the plot of absorbance ratio (A650/A528) against the concentration of histidine, shows a linear relation in the concentration range of 100 - 800 nM. The limit of detection (LOD) and limit of quantitation (LOQ) of the method were found to be 99.88 and 107.45 nM, respectively. Good recoveries were also obtained (range: 99.75 - 104.43%) with relative standard deviations (RSDs) below 5.89% in real water samples. Moreover, this method can be used for the selective detection of histidine even in the presence of other amino acids. The proposed method has been successfully used in the determination of histidine in mineral water samples.

Sensing of mercury and silver ions using branched Au nanoparticles prepared by hyperbranched polyethylenimine fabricated and capped AuNPs seeds

Branched AuNPs usually have two or more local surface plasmon resonance (LSPR) absorption bands due to their structural anisotropy, and the LSPR performance is more sensitive to the changes of environmental refractive index than that of spherical AuNPs. The design and preparation of branched AuNPs as colorimetric probes is expected to improve the selectivity and sensitivity of detection of targets. In this paper, branched AuNPs were innovatively synthesized via hyperbranched polyethylenimine (HPEI) fabricated and capped AuNPs as seeds and cetyltrimethylammonium bromide (CTAB) as template agent. The branched AuNPs were characterized by TEM, DLS, zeta potentials and UV-vis spectra. Using the branched AuNPs as a colorimetric probe, the detection system for Hg²⁺and Ag⁺showed bright color changes from blue to orange and blue to green based on the morphological evolution of branched AuNPs. The branched AuNPs could selectively detect Hg²⁺and Ag⁺at concentrations as low as 77 and 140 nM, respectively. Moreover, this unusual colorimetric method has been successfully used in real water samples and has great potential as a simple, rapid, sensitive and selective method for the detection of Hg²⁺and Ag⁺.

An asymmetric Schiff base-functionalized gold nanoparticle-based colorimetric sensor for Hg2+ ion determination: experimental and DFT studies

We report a colorimetric sensor for the detection of Hg²⁺ ions utilizing surface-modified gold nanoparticles. Gold nanoparticles (GNPs) were synthesized by direct reduction and were subsequently functionalized using Schiff base ligands. Schiff base ligands as electron transfer agents have been frequently used for the determination of heavy metal ions. From the spectroscopic analysis, it was found that the mechanism could be defined as coordination between azomethine nitrogen and the carbonyl oxygen of the ligand with Hg²⁺ ions. The affinity of Hg²⁺ ions towards the bidentate Schiff base on the GNPs result from their self-aggregation and investigated to be a powerful asset for the development of Hg²⁺ ion-selective sensors, which is accompanied by a visible color change from pink to purple or can be detect by UV-Vis spectroscopy. The optimized structures and binding mechanisms were supported with a high correlation and agreement via spectroscopy and DFT calculations. These simple colorimetric tests can be extended for the rapid pre-screening of a wide variety of heavy metal ions for onsite detection and mitigation.

Phenothiazine-Thiophene Hydrazide Dyad: An Efficient "On-Off" Chemosensor for Highly Selective and Sensitive Detection of Hg2+ Ions

A new phenothiazine-thiophene hydrazone based ((10-ethyl-10H-phenothiazine-3,7-diyl)bis(methanylylidene))bis(thiophene-2-carbohydrazide) (PHT) chemosensor was synthesized via a single-step reaction and utilized as fluorescence "On-Off" sensor towards Hg²⁺ ion. The PHT was fully characterized by FT-IR, ¹H-NMR, and ESI-Mass spectral analysis. The PHT probe was efficiently used for the selective detection of Hg²⁺ ion in the presence of other metal ions. Further, the stoichiometry of the PHT with Hg²⁺ complex was confirmed by Job's plot analysis. The limit of detection (LOD) value of the probe PHT was found to be 0.44 × 10^-8 M.

Chemical sensing with Au and Ag nanoparticles

Noble metal nanoparticles (NPs) are ideal scaffolds for the fabrication of sensing devices because of their high surface-to-volume ratio combined with their unique optical and electrical properties which are extremely sensitive to changes in the environment. Such characteristics guarantee high sensitivity in sensing processes. Metal NPs can be decorated with ad hoc molecular building blocks which can act as receptors of specific analytes. By pursuing this strategy, and by taking full advantage of the specificity of supramolecular recognition events, highly selective sensing devices can be fabricated. Besides, noble metal NPs can also be a pivotal element for the fabrication of chemical nose/tongue sensors to target complex mixtures of analytes. This review highlights the most enlightening strategies developed during the last decade, towards the fabrication of chemical sensors with either optical or electrical readout combining high sensitivity and selectivity, along with fast response and full reversibility, with special attention to approaches that enable efficient environmental and health monitoring.

Fluorescence resonance energy transfer between carbon quantum dots and silver nanoparticles: Application to mercuric ion sensing

Fluorescence resonance energy transfer (FRET) process as a practical and competitive sensing strategy was utilized between carbon quantum dots (C-dots) and silver nanoparticles (Ag NPs) for the determination of mercuric ions. The novel synthesized C-dots with the quantum yield of 84% acted as the donor and Ag NPs operated as the acceptor in the FRET process leading to the fluorescence quenching of the C-dots. In the presence of Hg(II) ions, the FRET-quenched fluorescence emission of the C-dots-Ag NPs system was recovered owing to oxidation of Ag NPs by Hg(II) ions, so that the turn-on fluorescence intensity was directly proportional to the Hg(II) ion concentration. Accordingly, combination of the FRET system with the redox reaction was firstly utilized to construct an innovative turn-off/on fluorescent sensor for the quantification of Hg(II) ion. The calibration plot was linear in the concentration range 0.5-500.0 nmol L^-1 with a determination coefficient (R²) of 0.9965. The limit of detection and limit of quantification were 0.10 and 0.35 nmol L^-1, respectively, according to the IUPAC definition. The method was applied for the determination of Hg(II) ion in lake water, wastewater and tea samples, and the proper relative recoveries (98.0-104.0%) were obtained for the spiked samples. The method has high potential to diagnose trace values of mercuric ions in real samples with high sensitivity and repeatability.

Ultrasensitive visual detection of Hg2+ ions via the Tyndall effect of gold nanoparticles

This work describes a new nanosensor for one-step ultrasensitive naked-eye detection of Hg²⁺ ions based on the target-triggered aggregation of gold nanoparticles showing a dramatically enhanced Tyndall effect.

On-site, rapid and visual method for nanomolar Hg2+ detection based on the thymine–Hg2+–thymine triggered “double” aggregation of Au nanoparticles enhancing the Tyndall effect

This work describes a new nanosensor for the simple, rapid, portable, colorimetric analysis of mercury(ii) (Hg²⁺) ions by combining the sensitive Tyndall effect (TE) of colloidal Au nanoparticles (AuNPs) with specific thymine–Hg²⁺–thymine (T–Hg²⁺–T) coordination chemistry for the first time. For the TE-inspired assay (TEA), in the presence of Hg²⁺ in a sample, the analyte can selectively mediate the hybridization of three types of flexible single-stranded DNAs (ssDNAs) to form stable rigid double-stranded DNAs (dsDNAs) via the T–Hg²⁺–T ligand interaction. Subsequent self-assembly of the dsDNAs with terminal thiol groups on the AuNPs' surfaces led to their “double” aggregation in addition to the lack of sufficient ssDNAs as the stabilizing molecules in a high-salt solution, resulting in a remarkably enhanced TE signal that positively relied on the Hg²⁺ level. The results demonstrated that such a TEA method enabled rapid naked-eye qualitative analysis of 625 nM Hg²⁺ within 10 min with an inexpensive laser pointer pen as an inexpensive handheld light source to generate the TE response. Making use of a smartphone for portable TE readout could further quantitatively detect the Hg²⁺ ions in a linear concentration range from 156 to 2500 nM with a limit of detection as low as 25 nM. Moreover, the developed equipment-free nanosensor was also used to analyze the Hg²⁺ ions in real samples including tap water, drinking water, and pond water, the obtained recoveries were within the range of 93.68 to 108.71%. To the best of our knowledge, this is the first report of using the AuNPs and functional nucleic acids to design a TE-based biosensor for the analysis of highly toxic heavy metal ions.

A new equipment-free colorimetric nanosensor was initially developed for quantitative point-of-need detection of nanomolar Hg²⁺ ions based on the enhancement in Tyndall effect of Au nanoparticles via their target-triggered “double” aggregation.

A solvent sensitive coumarin derivative coupled with gold nanoparticles as selective fluorescent sensor for Pb2+ ions in real samples

A coumarin based fluorescent molecule, 3-amino-2-cynano-3-(7-diethylamino-2-oxo-2H-chromen-3-yl)-acrylic acid ethyl ester (1) has been synthesized and characterised. Photophysical studies of 1 exhibit polarity dependent shift of its emission maxima which have been explained on the basis the existence of polar excited state of the molecule. Combination of compound 1 and citrate capped AuNPs (AuNPs/1 conjugate) has been used as a sensing tool for heavy metals. AuNPs/1 conjugate has been found to detect Pb²⁺ selectively by naked-eye color change as well as fluorescence enhancement. On addition of molecule 1 to gold nanoparticles solution, the color of the solution becomes reddish followed by quenching in fluorescence intensity. With gradual addition of Pb²⁺, the solution of AuNPs/1 conjugate becomes violet accompanied by a fluorescence enhancement. Excited state lifetime measurement revealed that compound 1 exhibits very fast decay pattern in aqueous medium whereas in AuNPs medium the lifetime of 1 increases. Upon addition of Pb²⁺ ions to that AuNPs/1 solution the lifetime of 1 decreases again. Based on the experimental observations the mechanism of sensing of lead has been proposed thoroughly. Initially compound 1 gets absorbed on the surface of the spherical gold nanoparticles. When Pb²⁺ is added, probably gold nanoparticles aggregates to form bigger particles by releasing compound 1 from its surface to show fluorescence enhancement.

Fluorometric determination of mercury(II) based on dual-emission metal-organic frameworks incorporating carbon dots and gold nanoclusters

Carbon dots and gold nanoclusters co-encapsulated by zeolitic imidazolate framework-8 (CDs/AuNCs@ZIF-8) have been obtained at room temperature. The composite has been applied to the ratiometric fluorescence determination of mercury(II). The composite shows fluorescence emission maxima at 440 and 640 nm under 360 nm excitation, due to the CDs and AuNCs, respectively (associated quantum yields were 18% and 17%, respectively). In the presence of Hg²⁺, the fluorescence at about 640 nm is quenched, while the fluorescence at about 440 nm is unaffected. The CDs/AuNCs@ZIF-8 composite allows the sensitive detection of Hg²⁺, with the fluorescence intensity ratio (I₆₄₀/I₄₄₀) decreasing linearly with Hg²⁺ concentration over the range 3-30 nM. The fluorescence emission of the composite changes color from red to blue with increasing Hg²⁺ under UV excitation, which can easily be discerned visually. This visual detection of Hg²⁺ is due to the high fluorescence quantum yields of the CDs and AuNCs and the ~ 200 nm separation between the two emission maxima. Graphical abstract (A) Schematic diagram showing the operating principle of the determination for Hg(II). (B) Digital graph of the solutions in absence and presence of 30 nM Hg(II) under a portable UV lamp.

Recovery of waste gold for the synthesis of gold nanoparticles supported on radially aligned nanorutile: the growth of carbon nanomaterials

Precious and expensive metals are lost each year through the discarding of old jewellery pieces and mine tailings. In this work, small amounts of gold were recovered by digestion with aqua regia from waste tailings. The recovered gold in the form of HAuCl₄ was then used to deposit Au⁰ onto radially aligned nanorutile (RANR) to form a supported catalyst material. The support material, RANR, was synthesized using the hydrothermal technique whereas the deposition of gold was achieved using the deposition–precipitation with urea method at various loadings. Electron microscopy was used to show that the structure of the support is a sphere formed by multiple nanorods aligned in a radial structure. The Au nanoparticles were observed at the tips of the nanorods. It was confirmed by XRD that the support was indeed a rutile phase of TiO₂ and that the Au nanoparticles had a face-centred cubic structure. The various catalysts were then used to synthesize carbon nanomaterials (CNMs) using the chemical vapour deposition technique. A parametric study varying the reaction temperature, duration and carbon source gas flow rate was conducted to study the effects these conditions have on the structural properties of the resulting CNMs. Here, it was found that mainly carbon nanofibers were formed and that the different reaction conditions influenced their graphicity, width, structure and thermal properties.

A hydrothermal method was used to prepare rutile TiO₂ dandelions. A deposition–precipitation method using urea (DPU) was used to load Au metal nanoparticles in calculated weight percentages and the Au/RANR catalysts where used to synthesise CNFs in a CVD reaction.

Triggered peroxidase-like activity of Au decorated carbon dots for colorimetric monitoring of Hg2+ enrichment in Chlorella vulgaris

Developing a rapid, low-cost, and multimode detection method for heavy metal ions remains a compelling goal for many applications, including food safety, environmental and biological analysis. This study investigated the influence of Hg²⁺ on the peroxidase-like activity of gold nanoparticles (GNPs) decorated on carbon dots (CDs) from lysine (denoted as GNP@CDs). A new type of Hg²⁺-triggered peroxidase-like activity of GNP@CDs was discovered, which could catalyze the oxidation of the colorless 3,3',5,5'-tetramethylbenzidine (TMB) into blue TMB. Based on the regulation of the catalytically triggered activity, a sensitive colorimetric method for the detection of Hg²⁺ was developed, with a linear range of 7-150 nM, providing a limit of detection as low as 3.7 nM. The sensor is simple and rapid, and was successfully applied to the detection of Hg²⁺ enrichment in chlorella, suggesting a promising application in biological analysis.

Colorimetric sensing of iodide ions based on unmodified gold nanoparticles and the distinctive antiaggregation-to-aggregation process

A highly sensitive and selective colorimetric analysis method based on unmodified gold nanoparticles (AuNPs) to detect iodide ions (I^- ) in solution in the presence of hexadecyl trimethyl ammonium bromide (CTAB) and mercury ions (Hg²⁺ ) has been successfully developed. Hg²⁺ could form a gold amalgam with AuNPs to protect AuNPs from CTAB-induced aggregation caused by the electrostatic attraction between CTAB and citrate ion-covered AuNPs. When a mixture of Hg²⁺ and I^- was added to the solution of AuNPs, the formation of the HgI₂ complex destroyed the protection of Hg²⁺ for AuNPs, which led to the aggregation of AuNPs accompanied with the change in colour of the solution from red to grey black and decrease in the absorbance of AuNPs at 520 nm. There was a good linear relationship between A_520nm and I^- concentration from 0 to 800 nM with a low limit of detection (LOD) of 4.2 nM. Furthermore, this simple and reliable colorimetric sensor has been applied successfully to the detection of I^- in practical samples.

Label-free, sensitive colorimetric detection of mercury(II) by target-disturbed in situ seeding growth of gold triangular nanoprisms

Gold nanomaterials have been used extensively in colorimetric detection of mercuric ions (Hg²⁺) due to their shape- and size-dependent, ultrastrong localized surface plasmon resonance (LSPR). Conventional detection was performed by first synthesizing the nanomaterials, and then applying them to signal-transducing reactions. We herein report a convenient method for detecting Hg²⁺ based on gold triangular nanoprisms (AuTNPs). During the seeding-growth process, Hg²⁺ added to the growth solution was co-reduced and deposited on the high-energy facets of the gold seeds, affecting the deposition patterns of the subsequently generated Au⁰ and ultimately leading to the formation of defective AuTNPs. Morphological changes were reflected by the in-plane dipole LSPR wavelength shift, which was proportionally related to the concentration of Hg²⁺. To improve the selectivity, the interference from Ag⁺ was eliminated by a stepwise preparation-selective precipitation approach. Under the optimized conditions, Hg²⁺ could be selectively detected with 20 min, with a detection limit of 0.12 nM. Finally, the method was successfully applied to detecting trace Hg²⁺ in fortified drinking, mineral and rain water samples, with recoveries ranging from 95.17% to 110.6%.

Simplified Mercury Extraction from Coal Fly Ash for Quantification of Total Mercury by ELISA-based Immunoassay

A simplified two-step mercury extraction procedure enabled the selective and reproducible mercury recovery from actual coal fly ash (CFA). The optimized extraction procedure involving conventional enzyme-linked immunosorbent assay (ELISA)-based immunoassay allowed the ultra-sensitive quantification of total mercury content in CFA. The total mercury content of 41 CFA samples were successfully determined using the above-mentioned method, and the results were in agreement with those obtained by standard instrumental analysis (thermal decomposition atomic absorption spectrometry) within a 15% coefficient of variation. Our method for total mercury quantification is not only simple but suitable for management of the mercury content at coal-fired electric power plants and landfill sites, which deal with large amounts of waste CFA.

Colorimetric Sensor Array Based on Amino Acid-Modified Gold Nanoparticles for Toxic Metal Ion Detection in Water

Several chromatographic and spectroscopic methods are available for the detection of toxic mercury (Hg²⁺) in water; however simple, rapid, inexpensive, and sensitive methods are still needed. In this chapter, we describe a facile, very sensitive, and rapid method for the colorimetric detection of Hg²⁺ in water with the detection limit of 2.9 nM. This simple procedure is based on the lysine-induced aggregation of citrate-capped gold nanoparticles (AuNPs) in the presence of Hg²⁺ ions.

Recent Advances in Nanomaterials for Analysis of Trace Heavy Metals

In an effort to achieve high sensitivity analysis methods for ultra-trace levels of heavy metals, numerous new nanomaterials are explored for the application in preconcentration processes and sensing systems. Nanomaterial-based methods have proven to be effective for selective analysis and speciation of heavy metals in combination with spectrometric techniques. This review outlined the different types of nanomaterials applied in the field of heavy metal analysis, and concentrated on the latest developments in various new materials. In particular, the functionalization of traditional materials and the exploitation of bio-functional materials could increase the specificity to target metals. The hybridization of multiple materials could improve material properties, to build novel sensor system or achieve detection-removal integration. Finally, we discussed the future perspectives of nanomaterials in the heavy metal preconcentration and sensor design, as well as their respective advantages and challenges. Despite impressive progress and widespread attention, the development of new nanomaterials and nanotechnology is still hampered by numerous challenges, particularly in the specificity to the target and the anti-interference performance in complex matrices.

Controllable and robust dual-emissive quantum dot nanohybrids as inner filter-based ratiometric probes for visualizable melamine detection

The ratiometric fluorescence technique is of great interest due to its visualization characteristics. The construction of a reliable fluorescent ratiometric nanoprobe for high-sensitivity visual quantification is highly sought after but it is limited by poor stability and controllability. Herein, we report a robust dual-emissive quantum dot nanohybrid with precise color tunability and demonstrate its potential as a two-signal-change ratiometric probe for visual detection. A novel assembly strategy was developed for spatially implanting hydrophobic green and red quantum dots (QDs) into a silica scaffold to form a dual-emissive hierarchical fluorescent silica nanohybrid. The fluorescence intensity ratio and color of the nanohybrid were precisely tailored by altering the amounts of green and red QDs. Particularly, after the alkylsilane-mediated phase transfer and exterior silica shell growth, the nanohybrid exhibited the well-preserved fluorescence features of the original QDs and robust optical/colloid stability. An inner filter-based ratiometric nanoprobe for the visual determination of melamine was ultimately devised by combining the spectra-overlapped two-colored fluorescent nanohybrid with analyte-specific gold nanoparticles. Furthermore, based on the reversible fluorescence signal changes in two-colored QDs induced by melamine, a logic gate strategy for melamine monitoring was constructed. The newly developed fluorescent ratiometric nanoprobe shows great prospects for the visual and quantitative determination of analytes in a complex biological matrix.

Bovine Serum Albumin Protein-Based Liquid Crystal Biosensors for Optical Detection of Toxic Heavy Metals in Water

A new methodology involving the use of Bovine Serum Albumin (BSA) as a probe and liquid crystal (LC) as a signal reporter for the detection of heavy metal ions in water at neutral pH was developed. BSA acted as a multi-dentate ligand for the detection of multiple metal ions. The LC sensor was fabricated by immobilizing 3 µg mL-1 BSA solution on dimethyloctadecyl-[3-(trimethoxysilyl)propyl]ammonium chloride (DMOAP)-coated glass slides. In the absence of heavy metal ions, a dark optical image was observed, while in their presence, a dark optical image turned to bright. The optical response was characterized by using a polarized optical microscope (POM). The BSA based LC sensor selectively detected toxic metal ions as compared to s block metal ions and ammonium ions in water. Moreover, the limit of detection was found to be very low (i.e., 1 nM) for the developed new biosensor in comparison to reported biosensors.