Sensitive Dual-Mode Biosensors for CYFRA21-1 Assay Based on the Dual-Signaling Electrochemical Ratiometric Strategy and "On-Off-On" PEC Method

Enzyme-free immunoassay for rapid, sensitive, and selective detection of C-reactive protein

C-reactive protein (CRP) is a protein made by the liver, which is released into the bloodstream in response to inflammation. Furthermore, CRP is a potential risk factor for heart disease. Hence, it is of great importance to develop a rapid, sensitive, accurate, and cost-effective method for CRP detection. Herein, we report an enzyme-free fluorescent assay for the rapid and ultra-sensitive detection of CRP with a limit of detection (LOD) reaching as low as 3.08 pg/mL (i.e., ~ 27 fM). The high sensitivity of our method was simply achieved via dual-functionalized gold nanoparticles (AuNPs). By regulating the molar ratio of DNA to CRP antibody immobilized on the AuNP surface, hundreds to thousands-fold amplification in the analyte signal could be instantly accomplished. Furthermore, our sensor was selective: non-target proteins such as interleukin-6, interleukin-1β, procalcitonin, bovine serum albumin, and human serum albumin did not interfere with the target CRP detection. Moreover, simulated serum samples were successfully analyzed. Given the excellent sensitivity, selectivity, and high resistance to complicated matrices, the enzyme-free CRP detection strategy developed in this work can be used as a generic platform to construct sensors for a wide variety of protein biomarkers and hence offers potential as a tool for rapid, accurate, and low-cost medical diagnosis.

A colorimetric/electrochemical microfluidic biosensor using target-triggered DNA hydrogels for organophosphorus detection

Organophosphorus compounds are widely distributed and highly toxic to the environment and living organisms. The current detection of organophosphorus compounds is based on a single-mode method, which makes it challenging to achieve good portability, accuracy, and sensitivity simultaneously. This study designed a multifunctional microfluidic chip to develop a dual-mode biosensor employing a DNA hydrogel as a carrier and aptamers as recognition probes for the colorimetric/electrochemical detection of malathion, an organophosphorus compound. The biosensor balanced portability and stability by combining a microfluidic chip and target-triggered DNA hydrogel-sensing technologies. Moreover, the biosensor based on target-triggered DNA hydrogel modified microfluidic developed in this study exhibited a dual-mode response to malathion, providing both colorimetric and electrochemical signals. The colorimetric mode enables rapid visualization and qualitative detection and, when combined with a smartphone, allows on-site quantitative analysis with a detection limit of 56 nM. The electrochemical mode offers a broad linear range (0.01-3000 μM) and high sensitivity (a limit of detection of 5 nM). The two modes could validate each other and improve the accuracy of detection. The colorimetric/electrochemical dual-mode biosensor based on target-triggered DNA hydrogel modified microfluidic chip offers a portable, simple, accurate, and sensitive strategy for detecting harmful environmental and food substances.

Development of photoelectrochemical immunosensor based on halide perovskite protected by organometallic compounds for determining interleukin-17A (IL-17A)

The overexpression of interleukin-17A (IL-17A) is closely associated with the pathogenesis of autoimmune diseases and cancer, rendering precise identification of IL-17A level critical for disease diagnosis and prognosis monitoring. In this study, CsPbBr3 nanoclusters (NCs) were embedded in C16H14Br2O6Pb2 organometallic compound (Pb-MA MOC) via a hot injection approach. Through this way, the issue of CsPbBr3 NCs susceptible to decomposition in water was solved, and the photocurrent intensity that is generated by CsPbBr3 was significantly enhanced. A highly sensitive photoelectrochemical (PEC) sensor for detecting IL-17A in human serum was developed using CsPbBr3/Pb-MA as the photoactive material. The electrode was initially modified with CsPbBr3/Pb-MA. Then, antibody-modified Fe3O4 magnetic nanoparticles (MNs) with target analyte IL-17A captured, and IL-17A antibody-modified Au@CuNi diatomic catalyst (DAC) formed sandwich immune complex structure on the electrode. The existence of CuNi DAC led to a substantial reduction in photoelectric signal intensity due to oxidation of ascorbic acid in the supporting electrolyte. The photocurrent intensity exhibited linear correlation with IL-17A concentration within the range 15-750 pg/mL, and achieving an impressive detection limit of 1 pg/mL. Moreover, the sensor was successfully applied to the determination of IL-17A in human serum, suggesting its potential clinical applications.

Cu2O-Mediated Heterojunction Conversion from Dual Type II to Dual Z-Scheme: Its Application in Photoelectric-Colorimetric Dual-Mode Detection of Fat Mass and Obesity-Associated (FTO) Protein

Although the construction of heterojunction has been used in photoelectrochemical (PEC) biosensors, their potential for tunable optical properties has not been deeply explored. Based on the fact that a type-II heterojunction and Z-scheme heterojunction have the same energy band structure, effective alteration of the electron transfer pathway has been achieved by introducing unique photoactive materials into the system and exploiting the interactions between the photomaterials. Based on this, we reported a novel polarity-switchable dual-mode sensor for fat mass and obesity-associated (FTO) protein analysis. Specifically, the MgIn2S4/Bi2MoO6/Bi2S3 dual type-II heterojunction was used as the sensing interface in concert with the rolling circle amplification, CRISPR/Cas12, and terminal DNA transfer enzyme multiamplification strategies, and finally, Cu2O was captured at the sensing interface. Due to the matched energy band, the introduction of Cu2O effectively changed the electron transfer pathway and realized the conversion from a dual type-II heterojunction to a dual Z-scheme heterojunction. It caused the switch of the photocurrent from the anode to the cathode. The developed PEC method showed high sensitivity and selectivity for FTO protein detection in the range of 0.0005-500 μg/L. In addition, based on the peroxidase-like activity of Cu2O to catalyze the oxidation of 3,3',5,5'-tetramethylbenzidine by H2O2, the electrode system also achieved the colorimetric detection of FTO protein using the naked eye with the change of the color of the detection solution from colorless to blue. The detection range was from 0.05 to 500 μg/L. This work developed a photoelectrochemical-colorimetric biosensing platform with consciously designed semiconductor structures, revealing the potential of semiconductor-structured transformations in future sensing fields.

Dual-mode biosensor using Tb-Cu MOF@Au nanoenzyme to effectively quench the photocurrent of Bi2O3/Bi2S3/AgBiS2 heterojunction and emit fluorescence for neuron-specific enolases detection

A novel dual-mode biosensor was constructed for the ultrasensitive detection of neuron-specific enolase (NSE), utilizing Tb-Cu MOF@Au nanozyme as the signal label to effectively quench the photoelectrochemical (PEC) signals of Bi2O3/Bi2S3/AgBiS2 composites and initiate fluorescent (FL) signals. First, Bi2O3/Bi2S3/AgBiS2 heterojunction with excellent photoelectric activity was selected as the substrate material to provide a stable photocurrent. The well-matched energy levels significantly enhanced the separation and transfer of photogenerated carriers. Second, a strategy of consuming ascorbic acid (AA) by Tb-Cu MOF@Au nanozyme was introduced to improve the sensitivity of the PEC/FL biosensor. Tb-Cu MOF@Au not only could catalyze the oxidation of AA, but the steric effect further reduced the contact of AA with the substrate. More importantly, in the presence of H2O2, a significant fluorescence was produced from Tb3+ sensitized by the oxidation products of AA. Based on the above strategies, a highly stable and sensitive dual-mode biosensor was proposed for accurate NSE determination. Third, the developed dual-mode biosensor demonstrated excellent performance in detecting NSE. In this study, the PEC method demonstrated a wide detection range from 0.00005 to 200 ng/mL with a low detection limit of 20 fg/mL. The FL method exhibited a linear range from 0.001 to 200 ng/mL with a detection limit of 0.65 pg/mL. The designed biosensor showed potential practical implications in the accurate detection of disease markers.

Advances in Aptamer-Based Biosensors for the Detection of Foodborne Mycotoxins

Foodborne mycotoxins (FBMTs) are toxins produced by food itself or during processing and transportation that pose an enormous threat to public health security. However, traditional instrumental and chemical methods for detecting toxins have shortcomings, such as high operational difficulty, time consumption, and high cost, that limit their large-scale applications. In recent years, aptamer-based biosensors have become a new tool for food safety risk assessment and monitoring due to their high affinity, good specificity, and fast response. In this review, we focus on the progress of single-mode and dual-mode aptasensors in basic research and device applications over recent years. Furthermore, we also point out some problems in the current detection strategies, with the aim of stimulating future toxin detection systems for a transition toward ease of operation and rapid detection.

A novel dual-model photoelectrochemical/electrochemical sensor based on Z-scheme TiO2 disks/methylene blue for kanamycin detection

Herein, a new dual-model photoelectrochemical (PEC)/electrochemical (EC) sensor based on Z-scheme titanium dioxide (TiO2) disk/methylene blue (MB) sensibilization for the detection of kanamycin (Kana) was developed. Metal-organic framework-derived porous TiO2 disks were synthesized and exhibited excellent anodic photocurrent under visible light excitation. Subsequently, amino-labeled double-stranded DNA (dsDNA) was introduced into the modified electrode. Photocurrent was enhanced with MB embedded in dsDNA to form Z-scheme TiO2/MB sensibilization. When the target, Kana, was present, it specifically bound to the aptamer in the dsDNA, leading to the disruption of the dsDNA structure and the release of MB. This release of MB and the increase in target spatial resistance resulted in a significant weakening of PEC signal and a decreased oxidation peak current of MB. The PEC sensor successfully detected Kana in the range of 2-1000 pM with an LOD of 0.17 pM. Meanwhile, the EC sensor for Kana detection showed a linear range of 5-500 pM with an LOD of 1.8 pM. Additionally, the sensor exhibited excellent selectivity, reproducibility, stability, and good recoveries when applied to milk and honey samples. As a result, this method has the potential for application in ensuring food safety through the rapid determination of antibiotics in food.

Organic photoelectrochemical transistor based on cascaded DNA network structure modulated ZnIn2S4/MXene Schottky junction for sensitive ATP detection

Organic photoelectrochemical transistor (OPECT) biosensor is now appearing in perspective of public, which characterized by amplified the grating electrode potential by ion transport. In this study, the DNA network formed by the hybridization chain reaction (HCR) detects the target adenosine triphosphate (ATP) by adjusting the surface potential of the new heterojunction of ZnIn2S4/MXene. The formation of DNA network amplifies the detection signal of ATP. Significantly, OPECT biosensor could further amplify the signal, which calculated the gain achieved 103, which is consistent with the gain signal of the previously reported OPECT biosensor. Furthermore, the OPECT biosensor achieved a highly sensitivity detection of the target ATP, which the linear detection range is 0.03 pM-30 nM, and the detection limit is 0.03 pM, and illustrated a high selectivity to ATP. The proposed OPECT biosensor achieved signal amplification by adjusting the surface potential of ZnIn2S4/MXene through cascade DNA network, which provides a new direction for the detection of biomolecules.

A novel split PEC sensor based on magneto-optic nanostructure and photocurrent polarity switching strategy

BACKGROUND

Photoelectrochemical (PEC) sensors have attracted much attention due to their low cost, simple instrumentation and high sensitivity. However, conventional PEC sensors require layer-by-layer modification of the photoelectrode surface, which has the disadvantages of being time-consuming and unstable. In addition, complex interfering substances in real samples may lead to false-positive or false-negative detection results. It was thought that the above drawbacks could be eliminated by the construction of a polarity inversion PEC sensor. In this work, a magnetically separated PEC sensor was constructed for the detection of Carcinoembryonic antigen (CEA).

RESULTS

During the experiment, the construction of the sensor was used for sensitive detection of CEA. In the experimental process, Fe3O4@SiO2@CdS, a semiconductor material with magnetic properties, was chosen as the substrate material, and ZnO/CuO was used as the marker on the DNA2 molecule, and a split magnetic separation PEC sensor was constructed, which was used to realize the sensitive detection of CEA. Eventually, the detection range of the sensor for CEA detection is 1-10000 pg/mL, with the detection limit of 0.34 pg/mL. Additionally, the PEC sensor has the advantages of high speed, high efficiency, high sensitivity, good specificity, and high stability. The sensing platform constructed in this work can also be extended to detect other targets, which provides a new idea for PEC sensing platforms.

SIGNIFICANCE

In this experiment, we developed a split PEC immunosensor based on magneto-optic nanostructure and photocurrent polarity switching strategy. Specifically, the proposed magnetic nanostructure Fe3O4@SiO2@CdS-DNA1 exhibits good paramagnetism and dispersion ability. By magnetic separation process, the PEC signals of opposite polarity can be obtained.

Band Alignment Modulated Polarity-Switchable PEC Ratiometric Sensor through Coupling a pH-Responsive CuTCPP MOF with i-Motif Sensing tool

In conventional ratiometric photoelectrochemical (PEC) sensors, the detection and reference signals are output sequentially from two independent photosensitive materials. In such a "two-to-two" ratiometric mode, unavoidable difference during dual-interface modification exists, resulting in questionable ratiometric signals and detection results. To address this issue, we propose a novel "one-to-two" ratiometric PEC sensor on a single electrode interface through pH-modulated band alignment engineering. The double ratiometric signals are generated by the synergistic action of a pH-responsive CuTCPP/WS2 photoelectric substrate material and the i-motif sensing tool. Specifically, a ternary heterostructure to generate a photoanodic detection signal is formed under alkaline conditions between CuTCPP/WS2 and signal label CdS QDs binding to the i-motif. While under acidic conditions, a photocurrent polarity conversion and signaling labels detachment, induced by the band realignment of CuTCPP/WS2 and the i-motif conformational switching, produce a reliable internal reference photocathodic signal. The feasibility of this two-wing signal generation strategy is validated by detecting mycotoxin ochratoxin A, which achieves accurate and reliable ratio detection results. Overall, this work provides guidance for the design of a PEC ratiometric determination system and exhibits great potential to be applied in practical analysis research.

High-Frequency Quartz Crystal Microbalance and Dual-Signaling Electrochemical Ratiometric Assays of PTP1B Activity Based on COF@Au@Fc Hybrids

The abnormal expression of protein tyrosine phosphatase 1B (PTP1B) is highly related to several serious human diseases. Therefore, an accurate PTP1B activity assay is beneficial to the diagnosis and treatment of these diseases. In this study, a dual-mode biosensing platform that enabled the sensitive and accurate assay of PTP1B activity was constructed based on the high-frequency (100 MHz) quartz crystal microbalance (QCM) and dual-signaling electrochemical (EC) ratiometric strategy. Covalent-organic framework@gold nanoparticles@ferrocene@single-strand DNA (COF@Au@Fc-S0) was introduced onto the QCM Au chip via the chelation between Zr4+ and phosphate groups (phosphate group of the phosphopeptide (P-peptide) on the QCM Au chip and the phosphate group of thiol-labeled single-stranded DNA (S0) on COF@Au@Fc-S0) and used as a signal reporter. When PTP1B was present, the dephosphorylation of the P-peptide led to the release of COF@Au@Fc-S0 from the QCM Au chip, resulting in an increase in the frequency of the QCM. Meanwhile, the released COF@Au@Fc-S0 hybridized with thiol/methylene blue (MB)-labeled hairpin DNA (S1-MB) on the Au NPs-modified indium-tin oxide (ITO) electrode. This caused MB to be far away from the electrode surface and Fc to be close to the electrode, leading to a decrease in the oxidation peak current of MB and an increase in the oxidation peak current of Fc. Thus, PTP1B-induced dephosphorylation of the P-peptide was monitored in real time by QCM, and PTP1B activity was detected sensitively and reliably using this innovative QCM-EC dual-mode sensing platform with an ultralow detection limit. This platform is anticipated to serve as a robust tool for the analysis of protein phosphatase activity and the discovery of drugs targeting protein phosphatase.

Dual-mode photoelectrochemical radar based on CdS quantum dot and Ce-MOF for detection of low-abundance disease-associated proteins

Herein, we developed a convenient and versatile dual-mode electrochemiluminescence (ECL) and photoelectrochemistry (PEC) sensing radar for the detection of Prostate-specific antigen (PSA), which has important implications for detection of low-abundance disease-associated proteins. Cerium-based metal-organic framework (Ce-MOFs) were firstly modified on the electrode, showing well ECL and PEC property. In particular, a unique multifunctional Au@CdS quantum dots (QDs) probe loaded numerous QDs and antibody was fabricated, not only displaying strong ECL and PEC signals, but also having specific recognition to PSA. After the signal probe was linked to the electrode by immune reaction, much amplified signals of ECL and PEC were generated for double-mode detection of PSA. Therefore, this work proposed a multifunctional Au@CdS QDs signal probe with excellent ECL and PEC performance, and developed an ultrasensitive photoelectric biosensing platform for dual-mode detection, which provides an effective method for health monitoring of cancer patients.

Oxygen vacancies-driven signal enhanced photoelectrochemical sensor for mercury ions detection

Mercury ion (Hg2+) poses a serious threat to human health due to its high toxicity. In this study, a smartphone-based photoelectrochemical sensor based on oxygen vacancies (OVs) driven signal enhancement for mercury ion detection was designed. BiVO4-x/Bi2S3/AuNPs were combined with T-Hg2+-T recognition mode to construct a multi-sandwich photoelectrochemical sensor. On the one hand, the OVs can increase the adsorption of light by the materials and enhance the photocurrent response as well as the superconductivity of Au NPs to accelerate the charge transfer at the electrode interface. On the other hand, the multi-sandwich structure was exploited to increase the binding site of Hg2+, as well as the T-Hg2+-T structure for sensitive recognition of Hg2+ and signal amplification. The sensor showed good linearity for Hg2+ concentration in the range of 0.1 nM-1.0 μM with a detection limit of 4.8 pM (S/N = 3). Eventually the smartphone-based real-time detection sensor is expected to contribute to the future analysis of heavy metal ions.

Dual-targets fluorescent nanoprobe for precise subtyping of lung cancer

A Au-Se bond-based nanoprobe using 3',3-diselenopropionic acid to simultaneously link response chains for Pro-GRP protein and Cyfra21-1 was developed. Early diagnosis and subtyping of lung cancer can be achieved based on the nanoprobes' differential response of the probes to the two targets in lung cancer patients' serum.

Exonuclease-catalyzed recycling and annular four-footed DNA walking amplification-assisted "on-off-super on" signal transitions for photoelectrochemical biosensing of kanamycin

Photoelectrochemical (PEC) biosensors have exhibited a promising potential for assays of a large variety of analytes; however, how to realize their low background-based "super on" signal output is still a great challenge. Herein, we report a novel multiple nucleic acid amplification-assisted "on-off-super on" signal transition mechanism for the PEC biosensing of kanamycin antibiotics. The biosensing platform was constructed on a perylene-3,4,9,10-tetracarboxylic dianhydride-based photoelectrode, and its strong photocurrent could be well inhibited by an anchored ferrocene (Fc)-labeled hairpin DNA to produce a low background signal. Two target biorecognition-triggered exonuclease III-catalytic reactions were adopted to produce an annular four-footed DNA walker (AFW) and a methylene blue (MB)-labeled DNA strand. By using their synergistic effect to release Fc quenchers and simultaneously capture MB sensitizers, a "super on" signal output was realized. As a result, a very wide linear range from 10 fg mL-1 to 10 ng mL-1 and an ultra-low detection limit of 7.8 fg mL-1 were obtained. Meanwhile, the aptamer recognition-based homogeneous reaction and AFW-based multiple nucleic acid amplification effectively simplified the assay manipulation and well ensured the repeatability of the method. The satisfactory sample experiment results indicated its good reliability and accuracy for the antibiotic residue analysis application.

Split aptamer-based sandwich-type ratiometric biosensor for dual-modal photoelectrochemical and electrochemical detection of 17β-estradiol

BACKGROUND

As one of the most potent environmental estrogens, 17β-estradiol (E2), which can be enriched into organisms through the food chain and cause harmful biological effects in humans, has been frequently detected in the water environment of the world. High performance liquid chromatography (HPLC) and gas chromatograohy-mass spectrometry (GC/MS) have been widely used for quantification of E2. Despite excellent accuracy, tedious pretreatment and expensive instruments result in their limited application. It is clear that there is an urgent need to establish simple, sensitive and accurate methods for the determination of E2.

RESULTS

A split aptamer-based sandwich-type ratiometric biosensor based on split aptamer was developed by coupling photoelectrochemical and electrochemical assays for E2 detection. For analysis, the two fragments of split aptamer recognized E2 by forming sandwich structure, which triggered hybridization chain reaction (HCR) to produce double-stranded DNA (dsDNA) with CdTe quantum dots (QDs) labeled hairpin DNA. The resultant dsDNA can further absorb methylene blue (MB) to sensitize CdTe QDs for an enlarged photocurrent (IPEC) and output a redox current of IMB, and both of them acted as response signals for detection; [Fe(CN)6]3-/4- probe produced redox current of I[Fe(CN)6]3-/4- as reference signal. Using IMB/I[Fe(CN)6]3-/4- and IPEC/I[Fe(CN)6]3-/4- as yardsticks, the developed split aptamer-based sandwich-type ratiometric biosensor provides two linear ranges of 0.1-5000 pg mL-1 for IMB/I[Fe(CN)6]3-/4- and 0.1-10000 pg mL-1 for IPEC/I[Fe(CN)6]3-/4- with detection limits of 0.06 pg mL-1 and 0.02 pg mL-1, respectively.

SIGNIFICANCE

These results of the biosensor are benefiting from the coupling of photoelectrochemical (PEC) and electrochemical (EC) assays as well as the unique cooperative recognition mechanism of split aptamer. This method not only enabled the biosensor to be successfully applied to the determination of E2 in lake water, but also broadens the prospects for the realization of sensitive and accurate detection of E2.

A dual-mode "signal-on" split-type aptasensor for bisphenol A via target-induced hybridization chain reaction amplification

Herein, a dual-mode detection system was constructed for efficient and accurate detection of bisphenol A (BPA) with the assistance of the BPA-induced hybridization chain reaction (HCR). The captured DNA (cDNA) was first modified on the surface of magnetic spheres modified with gold nanoparticles and polydopamine and then hybridized with the BPA aptamer to form double-stranded DNA (dsDNA). In the presence of the BPA target, the BPA aptamer was released from the surface of the magnetic sphere. The free cDNA triggered a HCR to construct a DNA duplex. Methylene blue (MB), as a bifunctional probe, was intercalated into the double-stranded DNA to amplify the photocurrent (IPEC) of the CdS-modified electrode and generate an electrochemical current (IEC) at the same time. Under the optimized conditions, the PEC and EC signal responses of the system were linear to the logarithm of BPA concentration in the range of 1.0 × 10-10 M to 1.0 × 10-5 M. The detection limits were found to be 1.27 × 10-11 M and 3.0 × 10-11 M using the PEC and EC methods, respectively. The constructed dual-mode biosensor exhibited good performance for real sample analysis, demonstrating its promising potential for practical applications. In addition, this dual-mode detection strategy provides more accurate and reliable detection results.

Proximity hybridization regulated dual-mode ratiometric biosensor for estriol detection in pregnancy serum

Sensitive and accurate determination of estriol level is vastly significant for the fetal growth and development. Herein, we constructed a dual-mode ratiometric biosensor for estriol assay combining the competitive immunoreaction, proximity hybridization with a two-step resonance energy transfer (RET) strategy. Estriol antibody and goat anti-rabbit antibody labeled DNA probes (Ab1-DNA1-Pt NPs and Ab2-DNA2) both hybridized with silver nanoclusters labeled DNA strands (H1-Ag NCs). Thus, the formed proximity hybridization enabled the occurrence of fluorescence RET (FL-RET, as the primary RET) between Ag NCs (donor) and Pt NPs (acceptor), quenching FL intensity of Ag NCs (FL off). When target estriol existed, the competitive reaction of Ab1-DNA1-Pt NPs with estriol and Ab2-DNA2 avoided the proximity hybridization. Then, the estriol-dependent H1-Ag NCs quenched electrochemiluminescence (ECL) emission of CdS quantum dots (CdS QDs, ECL off), generating ECL-RET (as the second RET). Consequently, according to the reverse changes of FL and ECL responses, this sensor realized the quantification of estriol from 1 to 100 ng/mL. Moreover, satisfactory results were achieved while testing estriol in pregnancy serum specimens, suggesting that the system is promising for potential application in samples analysis.

Detection of CYFRA 21-1 in human serum by an electrochemical immunosensor based on UiO-66-NH2@CMWCNTs and CS@AuNPs

In this study, an electrochemical immunosensor was constructed to detect the cytokeratin 19 fragment antigen 21-1 (CYFRA 21-1) in human serum. CYFRA 21-1 is the most sensitive tumor marker of non-small cell lung cancer (NSCLC), its content in normal human serum should be less than 3.3 ng/mL. When lung cancer cells dissolve or die, a myriad of CYFRA 21-1 is released into a tumor patient's blood circulation, and its serum content elevates strikingly. Consequently, detecting CYFRA 21-1 by an electrochemical biosensor is expected to provide a new method for the early detection and prevention of lung cancer. In this study, a composite of UiO-66-NH2 and carboxylated multi-walled carbon nanotubes (CMWCNTs) was used as the substrate material of a sensor; the resulting sensor had a large specific surface area and strong electrical conductivity. Moreover, gold nanoparticles (AuNPs) were used to bind to antibodies through an Au-S bonds. Also, a supersensitive detection of CYFRA 21-1 was achieved through the specific bindings of antigens and antibodies. Under optimal detection conditions, the change of current signal intensity of the immunosensor was proportional to the logarithm of CYFRA 21-1 concentration and had a linear relation in the range of 0.005-400 ng/mL, while the detection limit was 1.15 pg/mL (S/N = 3). The proposed immunosensor had high precision, stability, and selectivity. More importantly, the sensor was been successfully applied to detect CYFRA 21-1 in human serum with high recovery, providing a new method for early screening and dynamic monitoring of lung cancer.

A multifunctional electrochemiluminescence and photoelectrochemical biosensor based on a quantum dot ion-exchange reaction for two-channel detection of thrombin

Herein, a multifunctional electrochemiluminescence (ECL) and photoelectrochemical (PEC) biosensor based on exchange of Ag+ with CdTe QDs was developed for dual-mode detection of thrombin. First, CdTe QDs assembled on an electrode displayed superior ECL and PEC signals. At the same time, C-rich hairpin (HP) DNA linked to silicon spheres loaded a large amount of Ag+, and the specific binding of thrombin to an aptamer led to the release of DNA P; then, DNA P interacted with HP DNA to produce numerous Ag+ ions by an enzyme-digestion amplification reaction. Ag+ underwent ion exchange with CdTe QDs to generate AgTe/CdTe QDs, resulting in much reversed PEC and changed ECL signals for dual-mode detection of thrombin. This work takes advantage of outstanding multi-signals of QDs coupled with convenient ion exchange to achieve multi-mode detection of the target, avoiding false positive or false negative signals generated in the traditional detection process, and thus can be used for the rapid detection of various biomolecules in actual samples.

CRISPR/Cas12a-Powered EC/FL Dual-Mode Controlled-Release Homogeneous Biosensor for Ultrasensitive and Cross-Validated Detection of Messenger Ribonucleic Acid

Accurate detection of cancer-associated mRNAs is beneficial to early diagnosis and potential treatment of cancer. Herein, for the first time, we developed a novel CRISPR/Cas12a-powered electrochemical/fluorescent (EC/FL) dual-mode controlled-release homogeneous biosensor for mRNA detection. A functionalized ssDNA P2-capped Fe3O4-NH2 loaded with methylene blue (P2@MB-Fe3O4-NH2) was synthesized as the signal probe, while survivin mRNA was chosen as the target RNA. In the presence of the target mRNA, the nicking endonuclease-mediated rolling circle amplification (NEM-RCA) was triggered to produce significant amounts of ssDNA, activating the collateral activity of Cas12a toward the surrounding single-stranded DNA. Thus, the ssDNA P1 completely complementary to ssDNA P2 was cleaved, resulting in that the ssDNA P2 bio-gate on Fe3O4-NH2 could not be opened due to electrostatic interactions. As a result, there was no or only a little MB in the supernatant after magnetic separation, and the measured EC/FL signal was exceedingly weak. On the contrary, the ssDNA P2 bio-gate was opened, enabling MB to be released into the supernatant, and generating an obvious EC/FL signal. Benefiting from the accuracy of EC/FL dual-mode cross-verification, high amplification efficiency, high specificity of NEM-RCA and CRISPR/Cas12a, and high loading of mesoporous Fe3O4-NH2 on signal molecules, the strategy shows aM-level sensitivity and single-base mismatch specificity. More importantly, the practical applicability of this dual-mode strategy was confirmed by mRNA quantification in complex serum environments and tumor cell lysates, providing a new way for developing a powerful disease diagnosis tool.

Electrochemical Determination of Hazardous Herbicide Diuron Using MWCNTs-CS@NGQDs Composite-Modified Glassy Carbon Electrodes

Diuron (DU) abuse in weed removal and shipping pollution prevention always leads to pesticide residues and poses a risk to human health. In the current research, an innovative electrochemical sensor for DU detection was created using a glassy carbon electrode (GCE) that had been modified with chitosan-encapsulated multi-walled carbon nanotubes (MWCNTs-CS) combined with nitrogen-doped graphene quantum dots (NGQDs). The NGQDs were prepared by high-temperature pyrolysis, and the MWCNTs-CS@NGQDs composite was further prepared by ultrasonic assembly. TEM, UV-Vis, and zeta potential tests were performed to investigate the morphology and properties of MWCNTs-CS@NGQDs. CV and EIS measurements revealed that the assembly of MWCNTs and CS improved the electron transfer ability and effective active area of MWCNTs. Moreover, the introduction of NGQDs further enhanced the detection sensitivity of the designed sensor. The MWCNTs-CS@NGQDs/GCE electrochemical sensor exhibited a wide linear range (0.08~12 μg mL-1), a low limit of detection (0.04 μg mL-1), and high sensitivity (31.62 μA (μg mL-1)-1 cm-2) for DU detection. Furthermore, the sensor demonstrated good anti-interference performance, reproducibility, and stability. This approach has been effectively employed to determine DU in actual samples, with recovery ranges of 99.4~104% in river water and 90.0~94.6% in soil. The developed electrochemical sensor is a useful tool to detect DU, which is expected to provide a convenient and easy analytical technique for the determination of various bioactive species.

Emerging Biosensing Methods to Monitor Lung Cancer Biomarkers in Biological Samples: A Comprehensive Review

Lung cancer is the most commonly diagnosed of all cancers and one of the leading causes of cancer deaths among men and women worldwide, causing 1.5 million deaths every year. Despite developments in cancer treatment technologies and new pharmaceutical products, high mortality and morbidity remain major challenges for researchers. More than 75% of lung cancer patients are diagnosed in advanced stages, leading to poor prognosis. Lung cancer is a multistep process associated with genetic and epigenetic abnormalities. Rapid, accurate, precise, and reliable detection of lung cancer biomarkers in biological fluids is essential for risk assessment for a given individual and mortality reduction. Traditional diagnostic tools are not sensitive enough to detect and diagnose lung cancer in the early stages. Therefore, the development of novel bioanalytical methods for early-stage screening and diagnosis is extremely important. Recently, biosensors have gained tremendous attention as an alternative to conventional methods because of their robustness, high sensitivity, inexpensiveness, and easy handling and deployment in point-of-care testing. This review provides an overview of the conventional methods currently used for lung cancer screening, classification, diagnosis, and prognosis, providing updates on research and developments in biosensor technology for the detection of lung cancer biomarkers in biological samples. Finally, it comments on recent advances and potential future challenges in the field of biosensors in the context of lung cancer diagnosis and point-of-care applications.

Co-amplification of luminol-based electrochemiluminescence immunosensors based on multiple enzyme catalysis of bimetallic oxides CoCeOx and NiMnO3 for the detection of CYFRA21-1

The accelerated energy supply of co-reactants is an extremely effective strategy for achieving highly sensitive electrochemiluminescence analysis, and binary metal oxides would be an excellent tool for this purpose owing to the nano-enzyme acceleration of mixed metal valence states. Herein, an electrochemiluminescent (ECL) immunosensor for monitoring the concentration of cytokeratin 19 fragment antigen 21-1 (CYFRA21-1) was developed based on a co-amplification strategy triggered by two bimetallic oxides, CoCeO_x and NiMnO₃, with luminol as the luminophore. CoCeO_x derived from an MOF exhibits a large specific surface area and excellent loading capacity as a sensing substrate, and the peroxidase properties enable the catalysis of hydrogen peroxide to provide energy supply to the underlying radicals. The dual enzymatic properties of flower-like NiMnO₃ were employed as probe carriers for luminol enrichment. The peroxidase properties built on Ni²⁺/Ni³⁺ and Mn³⁺/Mn⁴⁺ binary redox pairs resulted in the integration of highly oxidative hydroxyl radicals, and the oxidase properties provided additional superoxide radicals via dissolved oxygen. The practically proven multi-enzyme-catalyzed sandwich-type ECL sensor easily accomplished an accurate immunoassay of CYFRA21-1, harvesting a detection limit of 0.3 pg mL^-1 in the linear range of 0.001-150 ng mL^-1. In conclusion, this work explores the cyclic catalytic amplification of mixed-valence binary metal oxides with nano-enzyme activity in the field of ECL and develops an effective pathway for ECL immunoassay.

Bismuth-based metal-organic framework peroxidase-mimic nanozyme: Preparation and mechanism for colorimetric-converted ultra-trace electrochemical sensing of chromium ion

A colorimetric-electrochemical dual-mode analytical method based on bismuth metal-organic framework nanozyme was developed for label-free and trace/ultra-trace Cr⁶⁺ detection. 3D ball-flower shaped bismuth oxide formate (BiOCOOH) was used as the precursor and template to facilely construct the metal-organic framework nanozyme BiO-BDC-NH₂, which possesses intrinsic peroxidase-mimic activity to effectively catalyze the colorless 3,3',5,5'-tetramethylbenzidine into blue oxidation products in the presence of hydrogen peroxide. Based on Cr⁶⁺ to promote the peroxide-mimic activity of BiO-BDC-NH₂ nanozyme, a colorimetric method for Cr⁶⁺ detection was developed with the detection limit of 0.44 ng mL^-1. Cr⁶⁺ can be electrochemically reduced to Cr³⁺ that would specifically inhibit the peroxidase-mimic activity of BiO-BDC-NH₂ nanozyme. Thus, the colorimetric system for Cr⁶⁺ detection was converted into a low-toxic and signal-off electrochemical sensor. The electrochemical model showed upgraded sensitivity and a lower detection limit of 9.00 pg mL^-1. The dual-model method was developed for selective appropriate sensing instruments in different detection scenarios, which can provide built-in correction for environmental effects, as well as the development and utilization of dual-signal sensing platforms for trace to ultra-trace Cr⁶⁺ rapid assay.

In-depth interpretation of aptamer-based sensing on electrode: Dual-mode electrochemical-photoelectrochemical sensor for the ratiometric detection of patulin

Electrochemical aptasensors have been extensively used to quantify food contaminants (e.g., mycotoxin) by using high-affinity aptamer for target recognition. Yet, analytical performance of aptasensors using different aptamers can be varied for the same target. Here, four aptamers with different sequences (i.e., A22, A34, A42, and A45) of patulin (PAT) were selected to estimate sensing behaviors at electrodes with electrochemical (EC) and photoelectrochemical (PEC) assays. Synergistic effect of steric hindrance and electron transfer distance was found to significantly affect EC and PEC response for PAT at aptasensors fabricated with A22, A34, A42, or A45. Eventually, A22 emerged to be the optimal aptamer for aptasensing, despite the highest affinity of A42 to PAT. The A22-based EC-PEC dual-mode ratiometric aptasensor offered a linear range of 50 fg mL^-1 - 500 ng mL^-1 with a detection limit of 30 fg mL^-1 for PAT, and it was applied to apple product (i.e., juice, puree) analysis.

Sensitive dual-mode detection of carbendazim by molecularly imprinted electrochemical sensor based on biomass-derived carbon-loaded gold nanoparticles

A dual-mode electrochemical sensor was fabricated for carbendazim (CBD) detection. Biomass-derived carbon loaded gold nanoparticles (AuNPs/BC) were firstly coated on a glassy carbon electrode (GCE), and then molecularly imprinted polymer (MIP) of o-aminophenol was prepared on the resulting AuNPs/BC/GCE through electrochemical method in the presence of CBD. The AuNPs/BC had excellent conductivity, large surface and good electrocatalysis, while the imprinted film presented good recognition. Thus, the obtained MIP/AuNPs/BC/GCE exhibited sensitive current response to CBD. Furthermore, the sensor displayed good impedance response to CBD. Hence, a dual-mode detection platform for CBD was established. Under optimum conditions, the linear response ranges were as wide as 1.0 nM - 15 μM (by differential pulse voltammetry, DPV) and 1.0 nM - 10 μM (by electrochemical impedance spectroscopy, EIS), and the detection limits for these two methods were as low as 0.30 nM (S/N = 3) and 0.24 nM (S/N = 3), respectively. The sensor also had high selectivity, stability and reproducibility. The sensor was applied to detect CBD in spiked real samples, including cabbage, peach, apple and lake water, and the recoveries were 85.8-108% (by DPV) and 91.4-110% (by EIS); the relative standard deviations (RSD) were 3.4-5.3% (by DPV) and 3.7-5.1% (by EIS), respectively. The results were consistent with that obtained by high-performance liquid chromatography. Therefore, this sensor is a simple and effective tool for CBD detection, and it has good application potential.

A fluorescence-electrochemiluminescence dual-mode sensor based on a "switch" system for highly selective and sensitive K-ras gene detection

Herein, an fluorescence (FL)-electrochemiluminescence (ECL) dual-mode biosensor is constructed based on the dual-signal "turn-on" strategy of functionalized metal-organic frameworks nanosheets (RuMOFNSs)-tetraferrocene for K-ras gene detection, and the mechanism of bursting through front-line orbital theory is explained for the first time. Amino-functionalized tetraferrocene-labeled probe DNA molecules are linked to RuMOFNSs by covalent amide bonds, acting as FL and ECL intensity switches. The target DNA, complementary to the probe DNA, triggers cyclic amplification of the target by nucleic acid exonuclease III (Exo III), repelling tetraferrocene reporter groups away from RuMOFNSs and inhibiting the electron transfer process and photoinduced electron transfer (PET) effect. These phenomena induce a double turn-on of FL and ECL signals with a high signal-to-noise ratio. The developed FL-ECL dual-mode sensing platform provides sensitive detection of the K-ras gene with detection limits of 0.01 fM (the detection range is 1 fM to 1 nM) and 0.003 fM (the detection range is 0.01 fM to 10 pM), respectively. In addition, the proposed dual-mode sensor can be easily extended to detect other disease-related biomarkers by changing the specific target and probe base sequences, depicting potential applications in bioanalysis and early disease diagnosis.

A dual-mode ratiometric aptasensor for accurate detection of pathogenic bacteria based on recycling of DNAzyme activation

Pathogenic bacteria have a significant impact on food safety. Herein, an innovative dual-mode ratiometric aptasensor was constructed for ultrasensitive and accurate detection of Staphylococcus aureus (S. aureus) based on recycling of DNAzyme activation on gold nanoparticles-functionalized MXene nanomaterials (MXene@Au NPs). Electrochemiluminescent (ECL) emitter-labeled probe DNA (probe 2-Ru) containing the blocked DNAzyme was partly hybridized with aptamer and then captured by electrochemical (EC) indicator-labeled probe DNA (probe 1-MB) on electrode surface. When S. aureus presented, the conformation vibration of probe 2-Ru activated the blocked DNAzymes, leading to recycling cleavage of probe 1-MB and ECL tag close to electrode surface. Based on the reverse change tendencies of ECL and EC signals, aptasensor achieved S. aureus quantification from 5 to 10⁸ CFU/mL. Moreover, the self-calibration characteristic of the aptasensor with dual-mode ratiometric readout ensured the reliable measurement of S. aureus in real samples. This work showed useful insight into sensing foodborne pathogenic bacteria.

Dual-signal ratiometric electrochemical immunosensor constructed with snowflake-like FeSe2-AuNPs and PAA-ZIF@TB for sensitive detection of CYFRA21-1

In this study, a ratiometric electrochemical immunosensor has been developed to detect the cytokeratin 19 fragment 21-1 (CYFRA21-1) biomarker in a highly sensitive manner through a dual-signal output model. As one of signal indicators, snowflake-like FeSe₂ loaded with AuNPs (FeSe₂-AuNPs) as sensing substrate with good conductivity and large active sites provides a differential pulse voltammetry (DPV) signal at +0.4 V. Another signal indicator, toluidine blue (TB) with the water-solubility property is an excellent redox probe that can generate DPV signal at -0.3 V. To solve the water-solubility problem, the TB is absorbed with polyacrylic acid (PAA) functionalized ZIF-67 (PAA-ZIF-67), which retains the properties of ZIF-67 that are large specific surface area and strong adsorption properties. The ratio of signals, stemmed from PAA-ZIF@TB and FeSe₂-AuNPs (I_PAA-ZIF@TB/I_FeSe2-AuNPs), increases with the CYFRA21-1 concentration. Under optimal experimental conditions, CYFRA21-1 was detected in a wide dynamic range from 0.1 pg/mL to 100 ng/mL, with a lower limit of detection of 0.02 pg/mL. Looking ahead, this ratio based strategy provides prospective clinical applications for detecting other biomarkers.

Dual-mode biosensor platform based on synergistic effects of dual-functional hybrid nanomaterials

Detection of biomarkers is very vital in the prevention, diagnosis and treatment of diseases. However, due to the poor accuracy and sensitivity of the constructed biosensors, we are now facing great challenges. In addressing these problems, nanohybrid-based dual mode biosensors including optical-optical, optical-electrochemical and electrochemical-electrochemical have been developed to detect various biomarkers. Integrating the merits of nanomaterials with abundant active sites, synergy and excellent physicochemical properties, many bi-functional nanohybrids have been reasonable designed and controllable preparation, which applied to the construction dual mode biosensors. Despite the significant progress, further efforts are still needed to develop dual mode biosensors and ensure their practical application by using portable digital devices. Therefore, the present review summarizes an in-depth evaluation of the bi-functional nanohybrids assisted dual mode biosensing platform of biomarkers. We are hoping this review could inspire further concepts in developing novel dual mode biosensors for possible detection application.

Au nano-flower/organic polymer heterojunction-based cathode photochemical biosensor with reduction-accelerated quenching effect of porphyrin manganese

In this work, a novel reduction-accelerated quenching of manganese porphyrin (MnPP) based signal-off cathode photochemical (PEC) biosensor by using Au nano-flower/organic polymer (PTB7-Th) heterojunction as platform was proposed for ultrasensitive detection of Hg²⁺. Firstly, the photoactive PTB7-Th with Au nano-flower on electrode could form a typical Mott-Schottky heterojunction for acquiring an extremely high cathode signal. Meanwhile, the presence of target Hg²⁺ could bring in the formation of T-Hg²⁺-T based scissor-like DNA walker, which thus activated efficient Mg²⁺-specific DNAzyme based cleavage recycling to shear hairpin H2 on electrode to exposure abundant trigger sites of hybridization chain reaction (HCR) for in-situ decoration of quencher MnPP. Here, besides the steric hinderance and light competition effect of MnPP decorated DNA nanowires attributing to signal decrease, we for the first time testified the MnPP reduction-accelerated quenching that constantly consumed the photo-generated electron by using cyclic voltammetry (CV). As a result, the proposed biosensor had excellent sensitivity and selectivity to Hg²⁺ in the range of 1 fM-10 nM with a detection limit of 0.48 fM. The actual sample analysis showed that the biosensor could reliably and quantitatively identify Hg²⁺, indicating an excellent application prospect in routine detection.

Dual-quenching effects of methylene blue on the luminophore and co-reactant: Application for electrochemiluminescent-electrochemical ratiometric zearalenone detection

Methylene blue (MB) is a common multifunctional indicator, which can be applied as a quencher for electrochemiluminescence (ECL) analysis as well as a classical redox probe. Although it is relatively prevalent for MB to study the mechanism with Ru-based luminophores in ECL systems, there are few studies on the effects between MB and co-reactants. In this work, we proposed the first investigation of MB on the luminophore and co-reactant of the self-enhanced ECL composites (nitrogen-doped graphene quantum dots on Ru(bpy)₃²⁺-doped silica nanoparticles, NGQDs-Ru@SiO₂), respectively. The relatively narrow ECL spectrum of luminophore (Ru@SiO₂) and the suitable ultraviolet-visible absorption spectrum of MB led to the ECL resonance energy transfer between them, meanwhile the appropriate energy levels among them facilitated the electron transfer, resulting in a decreased ECL signal (quench mode I). Additionally, the co-reactant (NGQDs) was prone to π-π conjugation with MB due to its abundant π-electrons, which reduced the concentration of NGQDs' intermediates and triggered a weakened ECL signal (quench mode II). Therefore, the dual-quenching effects are ingeniously integrated and designed in one ECL-electrochemical (ECL-EC) ratiometric aptasensor for zearalenone detection, for demonstrating its efficacy in enhancing the sensitivity, which is 4.8-fold higher than Ru@SiO₂ alone. This innovative ratiometric aptasensor achieved a relatively wide linear range from 1.0 × 10^-15 to 5.0 × 10^-8 g mL^-1, and obtained a low detection limit of 8.5 × 10^-16 g mL^-1. Our proposed dual-quenching interactions between MB and NGQDs-Ru@SiO₂ will open a new prospective for ECL-EC ratiometric aptasensor, which further broaden the application in sensitive and precise analysis of mycotoxins.

A SERS-Fluorescence dual-signal aptasensor for sensitive and robust determination of AFB1 in nut samples based on Apt-Cy5 and MNP@Ag-PEI

Food aflatoxin B1 (AFB1) contamination greatly threatens human health and its sensitive determination is imperative. In this study, a surface-enhanced Raman scattering (SERS) and fluorescence dual-signal aptasensor was constructed for sensitive AFB1 detection in peanuts, walnuts, and almonds samples. Fluorescent dye cy5 was used as fluorophore and Raman reporter, while polyethyleneimine modified Ag coating magnetic nanoparticles (MNP@Ag-PEI) were utilized to absorb the cy5 modified aptamer (apt-cy5). Results indicated that linear ranges of 0.001-1000 ng/mL and 0.2-20,000 ng/mL with detection limits of 0.45 pg/mL and 0.135 ng/mL for the SERS and fluorescence methods were obtained, respectively, and AFB1 detection in the nut samples using the aptasensor achieved satisfactory recoveries of 95.2%-108.6% for SERS and 94.7%-109.7% for fluorescence. Compared with other mono signal detection, the established aptasensor facilely fused the merits of the two signals and improved the detection accuracy and flexibility.

Photocurrent-Polarity-Switching Photoelectrochemical Biosensor for Switching Spatial Distance Electroactive Tags

This work presents a photocurrent-polarity-switching-based photoelectrochemical (PEC) biosensing platform for ultrasensitive detection of microRNA-21 (miR-21) through target-triggered catalytic hairpin assembly (CHA) for modulation of methylene blue (MB) and ferrocene (Fc) positional configurations using double-shelled Cu-doped ZnS nanocages (NCs)-Au nanoparticles (NPs) as photoactive materials. In the presence of miR-21, the assembly of MB-labeled HP1 and Fc-labeled HP2 leads to the generation of a large amount of double-stranded DNA (HP1-HP2), which pushes MB away from the electrode surface and brings Fc close to the electrode surface, resulting in effectively quenching the enhanced PEC signal to activate the photocurrent-polarity-switching system. Benefiting from the distance-controllable strategy, the designed PEC bioanalysis can effectively eliminate false-positive and false-negative signals due to the change of different signal expression patterns (from traditional the "signal-on" mode to the photocurrent-polarity-switching mode), thereby significantly improving the sensing specificity and sensitivity. The proposed PEC sensing system exhibited satisfying photocurrent responses toward target miR-21 within the working range from 1.0 fM to 1 nM at a low limit of detection (LOD) of 0.58 fM. More importantly, we demonstrated the successful integration of the proposed PEC biosensor with a handheld wireless device for instant detection of miR-21 concentrations in practical samples.

Photoelectrochemical and visual dual-mode sensor for efficient detection of Cry1Ab protein based on the proximity hybridization driven specific desorption of multifunctional probe

Currently, the development of sensitive and visual strategy for Cry1Ab detection, particularly using a switchable dual-mode detection system based on a single component, remains a great challenge. Here, a photoelectrochemical (PEC) and visual dual-mode sensor was designed for Cry1Ab detection based on a proximity hybridization driven multifunctional probe. In the presence of Cry1Ab, specific desorption of the antibody-DNA conjugate was achieved via sufficient proximity hybridization, leading to the selective release of the multifunctional signal probe, i.e., antibody-labeled single-stranded DNA-gold nanoparticles (Ab₁-S1-AuNPs). The released Ab₁-S1-AuNPs reduced the photocurrent signal and produced a colored response, thereby achieving PEC and visual dual-mode detection based on a single component. Owing to the different signal generation mechanisms, two independent signals were obtained simultaneously, which provided self-verification to improve reliability and accuracy. Taking advantage of the PEC sensitive detection and visual prediction, the dual-mode sensor achieved efficient detection of the Cry1Ab protein. The developed sensor was successfully used to determine Cry1Ab in corn, wheat, and soil samples with satisfactory results. This method offers a promising biosensing platform for the on-site detection of Cry1Ab protein.

CoNi-RGO and NiCo2S4-ZIF/g-C3N4 signal amplified electrochemical immunosensors for sensitive detection of CYFRA 21-1

Herein, a signal amplified electrochemical immunosensor for the sensitive detection of cytokeratin 19 fragments (CYFRA 21-1) in human serum was discussed. The CoNi-RGO was used as a substrate for the sensor with excellent specific surface area and strong electrical conductivity, which enables more efficient attachment of antibodies. The introduction of the bimetallic sulfide NiCo₂S₄ composite ZIF material provides strong catalytic performance for the immunosensor. It is worth noting that, in addition to these satisfactory advantages, these two materials also show amazing signal amplification capacity. When the immunosensor works, the increase in electrical impedance decreases the electron transfer rate, making the electrochemical signal change obvious. The signal enhancement of immunosensors was emphasized by the marker during construction, and the experimental results were satisfactory. The proposed signal enhanced immunosensor had a linear relationship in the range of 0.001-10 ng/mL for CYFRA 21-1, and the minimum detection limit was 0.33 pg/mL for △I = 95.22 + 23.27 lg c. This demonstrates that the electrochemical immunosensor we constructed is successful and has a great developing potential.

Engineering the Signal Transduction between CdTe and CdSe Quantum Dots for in Situ Ratiometric Photoelectrochemical Immunoassay of Cry1Ab Protein

Controllable modulation of a response mode is extremely attracting to fabricate biosensor with programmable analytical performances. Here, we reported a proof-of-concept ratiometric photoelectrochemical (PEC) immunoassay of Cry1Ab protein based on the signal transduction regulation at the sensing interface. A sandwich-type PEC structure was designed so that gold nanorods sensitized quantum dots to fix primary antibody (Au NRs/QDs-Ab₁) and methylene blue sensitized QDs to combine a second antibody (MB/QDs-Ab₂), which served as photoelectric substrate and signal amplifier, respectively. Unlike common recognition element, such a sandwich-type PEC structure allowed for the in situ generation of two specific response signals. For analysis, Cry1Ab captured by Au NRs/QDs-Ab₁ led to a decreased photocurrent (I_Cry1Ab), while the subsequently anchored MB/QDs-Ab₂ produced another photocurrent (I_MB). Noteworthy, by taking advantage of the different energy band gaps of QDs, varying locations of CdTe and CdSe QDs could realize different signal transduction strategies (i.e., Mode 1 and Mode 2). Investigations on data analysis of I_Cry1Ab and I_MB via different routes demonstrated the superior analytical performances of ratiometry (Mode 1). Consequently, the ratiometric PEC immunosensor offered a linear range of 0.01-100 ng mL^-1 with a detection limit of 1.4 pg mL^-1. This work provides an efficient strategy for in situ collection of multiple photocurrents to design ratiometric PEC sensors.

Stimulus-Responsive Metal-Organic Framework Signal-Reporting System for Photoelectrochemical and Fluorescent Dual-Mode Detection of ATP

Dual-mode bioanalysis integrating photoelectrochemical (PEC) and other modes is emerging and allows signal cross-checking for more reliable results. Metal-organic frameworks (MOFs) have been shown to be attractive materials in various biological applications. This work presents the utilization of MOF encapsulation and stimuli-responsive decapsulation for dual-mode PEC and fluorescence (FL) bioanalysis. Photoactive dye methylene violet (MV) was encapsulated in zeolitic imidazolate framework-90 (ZIF-90) to form an MV@ZIF-90 hybrid material, and MV could be released by adenosine triphosphate (ATP)-induced ZIF-90 disintegration. The released MV not only had FL emission but also had a sensitization effect on the ZnIn₂S₄ (ZnInS) photoanode. Based on the MV-dependent sensitization effect and FL emission characteristic, a dual-mode PEC-FL strategy was established for ATP detection with low detection limits, that is, 3.2 and 4.1 pM for PEC and FL detection, respectively. This study features and will inspire the construction and implementation of smart MOF materials for dual-mode bioanalysis.

Ultrasensitive sandwich-typed electrochemical immunoassay for detection of squamous cell carcinoma antigen based on highly branched PtCo nanocrystals and dendritic mesoporous SiO2@AuPt nanoparticles

Squamous cell carcinoma antigen (SCCA) is one of the common squamous cell carcinomas (SCC) in women, which usually works as a tumor biomarker for cervical cancer in diagnostic applications. Herein, bimetallic PtCo highly branched nanocrystals (PtCo BNCs) acted as electrode substrates to construct sandwich-typed electrochemical immunosensor for ultrasensitive detection of SCCA, by using dendritic mesoporous SiO₂@AuPt nanoparticles (DM-SiO₂@AuPt NPs) to adsorb electroactive thionine (Thi) as a signal label. The PtCo BNCs enlarged the loading of the primary antibody (Ab₁), showing effective improvement in conductivity and sensitivity. The DM-SiO₂ had abundant pores to incorporate more Thi, on which the decorated AuPt NPs created a great number of active sites to immobilize the secondary antibodies (Ab₂), thereby obviously amplifying the detection signals. The prepared sensor exhibited a broader linear range (0.001-120 ng mL^-1) and a lower detection limit (0.33 pg mL^-1, S/N = 3), combined with high reproducibility, a low relative standard deviation (below 2.5%) and acceptable recovery (from 98.5 to 110.0%) even in diluted human serum samples. This research provides a substantial platform for clinical diagnosis of SCCA in practice.

Tuning the Surface Molecular Charge of Organic Photoelectrochemical Transistors with Significantly Improved Signal Resolution: A General Strategy toward Sensitive Bioanalysis

Nature makes use of molecular charges to operate specific biological synthesis and reactions. Targeting advanced opto-bioelectronic sensors, organic photoelectrochemical transistors (OPECTs), taking advantage of the light fuel substituting an external gate potential, is now debuting and expected to serve as a universal platform for studying the rich light-biomatter interplay for new bioanalytics. Given the ubiquity of charged biomolecules in nature, molecular charge manipulation should underpin a generic route for innovative OPECT regulation and operation, which nevertheless has remained unachieved. Herein, this work manifests the biological tuning of surface charge toward the OPECT biosensor, which was exemplified by a light-sensitive CdS quantum dot (QD) gate electrode interfaced by a smart DNA superstructure with adenosine triphosphate (ATP) responsiveness. Highly negative-charged supramolecular DNA concatemers were self-assembled via sequential hybridization, and the ATP-triggered disassembly of the DNA concatemers would cause a tandem change of the effective gate voltage and transfer characteristics with significantly improved resolution. The present opto-bioelectronic device translates the events of charged molecules into amplified electrical signals and outlines a generic format for the future exploitation of rich biological tunability and light-biomatter interplay for innovative bioanalytics and beyond.

Investigation of the effect of antibiotics on 5-formylcytosine content in mazie seedling tissues based on photoelectrochemical biosensor

Given the improved photoactivity of Bi₂S₃ by MXene, an article photoelectrochemical biosensor was designed for 5-formyl-2'-deoxycytidine (5fdCTP) detection, where Bi₂S₃: MXene was selected as photoactive material, polydopamine was used as solid electron donor and 5fdCTP capture reagent, calcined ZIF-8(C-ZIF-8) was chosen as the artificial enzyme. With the catalyzed by C-ZIF-8, 4-chloro-1-naphthol was allegro oxidized by H₂O₂ to form the insoluble benzo-4-chlorohexadienone, and then deposited on the surface of the electrode, Resulting in a decrease of the PEC response. Under the optimum conditions, the sensor has a linear range of 0.001-200 nM and a detection limit of 0.51 pM (3σ). The suitability of the developed method was appraised by investigating the effect of antibiotics on 5fdCTP content in the genomic DNA of the roots of maize seedlings. As a new detection platform, the application of this approach can be expanded to investigative the impact of other pollutants on the content of 5fdCTP in plant or animal tissues, explore the feasibility of 5fdCTP as a new indicator for the ecotoxicological effect of pollutants, and the photoelectrochemical method as a new assessment technique for the ecotoxicological effects of pollutants.

Nucleic acid isothermal amplification-based soft nanoarchitectonics as an emerging electrochemical biosensing platform

The emergence of nucleic acid isothermal amplification strategies based on soft nanoarchitectonics offers a new dimension to the traditional electrochemical technique, particularly because of its flexibility, high efficiency, and increased sensitivity for analytical applications. Various DNA/RNA isothermal amplification strategies have been developed for the design and fabrication of new electrochemical biosensors for efficient and important biomolecular detection. Herein, we provide an overview of recent efforts in this research field and the strategies for signal-amplified sensing systems, with their biological applications, current challenges and prospects in this promising new area.