Fundamental and Practical Insights on the Packing of Modern High-Efficiency Analytical and Capillary Columns

Preparation of high-efficiency HILIC capillary columns utilizing slurry packing at 2100 bar

Complex mixture analysis requires high-efficiency chromatography columns. Although reversed phase liquid chromatography (RPLC) is the dominant approach for such mixtures, hydrophilic interaction liquid chromatography (HILIC) is an important complement to RPLC by enabling the separation of polar compounds. Chromatography theory predicts that small particles and long columns will yield high efficiency; however, little work has been done to prepare HILIC columns longer than 25 cm packed with sub-2 μm particles. In this work, we tested the slurry packing of 75 cm long HILIC columns with 1.7 μm bridged-ethyl-hybrid amide HILIC particles at 2,100 bar (30,000 PSI). Acetonitrile, methanol, acetone, and water were tested as slurry solvents, with acetonitrile providing the best columns. Slurry concentrations of 50-200 mg/mL were assessed, and while 50-150 mg/mL provided comparable results, the 150 mg/mL columns provided the shortest packing times (9 min). Columns prepared using 150 mg/mL slurries in acetonitrile yielded a reduced minimum plate height (hmin) of 3.3 and an efficiency of 120,000 theoretical plates for acenaphthene, an unretained solute. Para-toluenesulfonic acid produced the lowest hmin of 1.9 and the highest efficiency of 210,000 theoretical plates. These results identify conditions for producing high-efficiency HILIC columns with potential applications to complex mixture analysis.

On-column modification for the creation of temperature-responsive stationary phases

Temperature-responsive liquid chromatography (TRLC) offers an alternative for retention and selectivity optimisation in HPLC. This approach thereby exploits temperature gradients on stimuli-responsive stationary phases and forfeits the necessity for solvent gradients, allowing analyses to be performed using aqueous mobile phases. Consequently, it can be employed as a green alternative to reversed-phase separations. However, current production to obtain temperature-responsive columns inherently require dedicated column packing processes with polymer-modified particles. To facilitate the development of temperature-responsive phases, a flow-through modification procedure was developed allowing on-column modification of aminopropyl silica columns. Three columns were manufactured using this novel flow-through approach, which achieved identical column efficiencies compared to existing TRLC column. Demonstrating the possibility of bypassing the dedicated packing processes without losing efficiency. Additionally, it was observed that flow-through produced columns yielded higher retention at elevated temperatures despite their reduced carbon load. Further investigation of the carbon load revealed the presence of stationary phase gradients, whose influence was studied via novel developed retention experiments, which revealed a negligible change reduction in retention upon a change of polymer modification from 19.8% to 14.5%. However, further decrease from 14.5% to 12.3% resulted in a larger change. Interestingly, a further enhancement in apparent plate numbers was observed when operating the column under a reversed flow, yielding an increasing stationary phase gradient. This on-column modification procedure demonstrates the potential for modification of existing (commercial) packed columns to achieve temperature-responsive phases without loss of efficiency or retention. Thus, not only facilitating accessibility to temperature-responsive phases, but also aiding with development of further generations of temperature-responsive phases by removing the need for packing optimisation. Additionally, a novel experiment was set up to easily investigate the effect of inhomogeneous stationary phases retention.

Ultralow flow liquid chromatography and related approaches: A focus on recent bioanalytical applications

Ultralow flow LC employs ultra-narrow bore columns and mid-range pL/min to low nL/min flow rates (i.e., ≤20 nL/min). The separation columns that are used under these conditions are typically 2-30 μm in inner diameter. Ultralow flow LC systems allow for exceptionally high sensitivity and frequently high resolution. There has been an increasing interest in the analysis of scarce biological samples, for example, circulating tumor cells, extracellular vesicles, organelles, and single cells, and ultralow flow LC was efficiently applied to such samples. Hence, advances towards dedicated ultralow flow LC instrumentation, technical approaches, and higher throughput (e.g., tens-to-hundreds of single cells analyzed per day) were recently made. Here, we review the types of ultralow flow LC technology, followed by a discussion of selected representative ultralow flow LC applications, focusing on the progress made in bioanalysis of amount-limited samples during the last 10 years. We also discuss several recently reported high-sensitivity applications utilizing flow rates up to 100 nL/min, which are below commonly used nanoLC flow rates. Finally, we discuss the path forward for future developments of ultralow flow LC.

Recent Trends in Graphene-Based Sorbents for LC Analysis of Food and Environmental Water Samples

This review provides an overview of recent advancements in applying graphene-based materials as sorbents for liquid chromatography (LC) analysis. Graphene-based materials are promising for analytical chemistry, including applications as sorbents in liquid chromatography. These sorbents can be functionalized to produce unique extraction or stationary phases. Additionally, graphene-based sorbents can be supported in various materials and have consequently been applied to produce various devices for sample preparation. Graphene-based sorbents are employed in diverse applications, including food and environmental LC analysis. This review summarizes the application of graphene-based materials in food and environmental water analysis in the last five years (2019 to 2023). Offline and online sample preparation methods, such as dispersive solid phase microextraction, stir bar sorptive extraction, pipette tip solid phase extraction, in-tube solid-phase microextraction, and others, are reviewed. The review also summarizes the application of the columns produced with graphene-based materials in separating food and water components and contaminants. Graphene-based materials have been reported as stationary phases for LC columns. Graphene-based stationary phases have been reported in packed, monolithic, and open tubular columns and have been used in LC and capillary electrochromatography modes.

Effect of Hydrophobic Moieties on the Assembly of Silica Particles into Colloidal Crystals

To boost the implementation of colloidal crystals (CCs) in separation science, the effects of the most common chromatographic reversed phases, that is, butyl and octadecyl, on the assembly of silica particles into CCs and on the optical properties of CCs are investigated. Interestingly, particle surface modification can cause phase separation during sedimentation because the assembly is highly sensitive to minute changes in surface characteristics. Solvent-induced surface charge generation through acid-base interactions of acidic residual silanol groups with the solvent is enough to promote colloidal crystallization of modified silica particles. In addition, solvation forces at small interparticle distances are also involved in colloidal assembly. The characterization of CCs formed during sedimentation or via evaporative assembly revealed that C4 particles can form CCs more easily than C18 particles because of their low hydrophobicity; the latter can only form CCs in tetrahydrofuran when C18 chains with a high bonding density have extra hydroxyl side groups. These groups can only be hydrolyzed from trifunctional octadecyl silane but not from a monofunctional one. Moreover, after evaporative assembly, CCs formed from particles with different surface moieties exhibit different lattice spacings because their surface hydrophobicity and chemical heterogeneity can modulate interparticle interactions during the two main stages of assembly: the wet stage of crystal growth and the late stage of nano dewetting (evaporation of interparticle solvent bridges). Finally, short, alkyl-modified CCs were effectively assembled inside silica capillaries with a 100 μm inner diameter, laying the foundation for future chromatographic separation using capillary columns.

Application of an in-house packed octadecylsilica-functionalized graphene oxide column for capillary liquid chromatography analysis of hormones in urine samples

Graphene oxide-based LC stationary phases were developed and applied for separating hormones from urine using capillaryLC-MS/MS. Using two analytical approaches - direct injection and column-switching arrangement - it was possible to evaluate the chromatographic parameters and perform tests on the raw biological fluid. Two stationary phases (SPs) were produced, varying the amino silica support particle diameter (Si, 5, and 10 μm). Graphene oxide was covalently bonded to the surface of Si particles, and this material was functionalized by the insertion of octadecylsilica groups, generating the SiGO-C18. Infra-red spectroscopy assays revealed that both steps were successful - supporting GO onto Si and further C18 customization. Scanning electron microscopy showed spherical geometries with minor irregularities and narrow particle size distribution for the produced SPs. The GO-coating rate was higher on the Si particles of 10 μm. As a result, the 10 μm produced column reported better resolution, efficiency, and peak capacity. Therefore, this SiGO-C18 capillary column (100 mm × 0.32 mm i.d., 10 μm dp) was applied successfully in a column-switching method to separate hormones in urine. Linearity (R2 above 0.99), quantification limits (between 1.0 and 5 μg/L), and other figures of merit of the method were determined. It is worth mentioning that the SiGO-C18 capillaryLC column performed adequately, separating the target compounds in less than 6 min. We hope this work could significantly contribute to shedding some light on graphene-based materials as a promising class of stationary phase for miniaturized liquid chromatography.

Reversed-Phase Liquid Chromatography of Peptides for Bottom-Up Proteomics: A Tutorial

The performance of the current bottom-up liquid chromatography hyphenated with mass spectrometry (LC-MS) analyses has undoubtedly been fueled by spectacular progress in mass spectrometry. It is thus not surprising that the MS instrument attracts the most attention during LC-MS method development, whereas optimizing conditions for peptide separation using reversed-phase liquid chromatography (RPLC) remains somewhat in its shadow. Consequently, the wisdom of the fundaments of chromatography is slowly vanishing from some laboratories. However, the full potential of advanced MS instruments cannot be achieved without highly efficient RPLC. This is impossible to attain without understanding fundamental processes in the chromatographic system and the properties of peptides important for their chromatographic behavior. We wrote this tutorial intending to give practitioners an overview of critical aspects of peptide separation using RPLC to facilitate setting the LC parameters so that they can leverage the full capabilities of their MS instruments. After briefly introducing the gradient separation of peptides, we discuss their properties that affect the quality of LC-MS chromatograms the most. Next, we address the in-column and extra-column broadening. The last section is devoted to key parameters of LC-MS methods. We also extracted trends in practice from recent bottom-up proteomics studies and correlated them with the current knowledge on peptide RPLC separation.

Continuous-Flow Synthesis of Arylthio-Cyclopropyl Carbonyl Compounds

The straightforward, continuous-flow synthesis of cyclopropyl carbaldehydes and ketones has been developed starting from 2-hydroxycyclobutanones and aryl thiols. This acid-catalyzed mediated procedure allows access to the multigram and easily scalable synthesis of cyclopropyl adducts under mild conditions, using reusable Amberlyst-35 as a catalyst. The resins, suitably ground and used for filling steel columns, have been characterized via TGA, ATR, SEM and BET analyses to describe the physical-chemical properties of the packed bed and the continuous-flow system in detail. To highlight the synthetic versatility of the arylthiocyclopropyl carbonyl compounds, a series of selective oxidation reactions have been performed to access sulfoxide and sulfone carbaldehyde cyclopropanes, oxiranes and carboxylic acid derivatives.

Mass Fabrication of Capillary Columns Based on Centrifugal Packing

Packed capillary columns have become the standard front-end separation device for mass spectrometry-based proteomics. The development of simple, fast, and robust capillary column technology, especially that with mass-fabrication capacity, can greatly improve analytical throughput and reproducibility in omics research. In this technical note, we report a centrifugal packing technology, which has the capability to mass fabricate high quality capillary columns with a 2886 columns/day fabrication throughput. The centrifugally packed columns presented significantly improved efficiency (reduced plate height h_min = 1.6, 37%-40% improvement compared with slurry packed columns), advanced kinetic performance limit, and excellent column-to-column reproducibility (2.0% RSD for retention time, 50 columns). Such columns enabled ∼5300 HeLa proteins identified in single-shot proteomic analysis, displaying both intercolumn and inter-run retention time stability (retention time RSD = 0.94% between nine replicates on three columns for probing peptide sequence). The mass-fabrication technology reported in this technical note may support disposable use of high quality chromatographic columns in large-scale bioanalysis.

High efficiency functionalized hydrophilic cyclofructans as stationary phases in sub/supercritical fluid chromatography

Packed column SFC has become very popular for preparative and analytical separations due to the low cost of CO₂, its accessible critical temperature, and pressure, with the additional benefit of a low environmental burden. Currently, there is a shortage of new polar stationary phase chemistries for SFC. In this work, two new functionalized cyclofructan columns are introduced and evaluated for their performance in achiral SFC separations for the first time. Cyclofructan (CF6), a macrocyclic oligosaccharide, was covalently linked with benzoic acid (BCF6) and propyl sulfonic acid (SCF6) groups by ether bonds. Superficially porous particles (2.7 μm) bonded with modified CF6 showed markedly different selectivity than native CF6. In SFC, peak shapes of amines and basic compounds are often compromised. We show that small quantities (~5.7% v/v) of water added to the methanol modifier in CO₂ improves peak symmetries of primary, secondary, and tertiary amines. Efficiencies as high as 200,000 plates/m (reduced plate height ~ 1.8) were observed for benzamide and amitriptyline on the BCF6 column. The relative standard deviations (RSDs) of retention times on BCF6 were about 1.4%, and on SCF6 were less than 1%. Amines on the SCF6 column showed plate counts as high as 170,000 plates/m. Tetramethylammonium acetate is examined as an alternative to water in MeOH. A run time of 36 min with methanol, trifluoroacetic acid, triethylamine mobile phase was reduced to <5 min with complete baseline resolution for a set of amines. The new stationary phases allow greener approaches towards solving separation problems.

Simultaneous enrichment of inorganic and organic species of lead and mercury in pg L-1 levels by solid phase extraction online combined with high performance liquid chromatography and inductively coupled plasma mass spectrometry

Quantification of ultra-trace inorganic and organic species of lead and mercury in unpolluted environmental water is crucial to estimate the mobility, toxicity and bioavailability and interactions. Simultaneous pre-concentration of Pb and Hg species in pg L^-1 levels followed by multi-elemental speciation analysis makes great sense to a large set of unstable samples because of time advantages. Herein simultaneous enrichment and speciation analysis of ultra-trace lead and mercury in water was developed by online solid-phase extraction coupled with high performance liquid chromatography and inductively coupled plasma mass spectrometry (SPE-HPLC-ICP-MS) for this aim. Pb(II), trimethyl lead (TML), triethyl lead (TEL), Hg(II), methylmercury (MeHg) and ethylmercury (EtHg) were baseline separated in 11 min under gradient elution using 5 mM l-cysteine (Cys) at pH 2.5 in the 0-1 and 4-15 min and 5 mM Cys + 0.5 mM tetrabutyl ammonium hydroxide solution at pH 2.5 in the 1-4 min. Lead and mercury species in 10 mL intact water samples were adsorbed on a 1 cm C₁₈ enrichment column pre-conditioned with 10 mL of 1 mM 2-mercaptoethanol at 10 mL min^-1, and then directly desorbed by the mobile phases. High enrichment factors (459 for Pb(II), 1248 for TML, 1627 for TEL, 2485 for Hg(II), 1984 for MeHg and 1866 for EtHg) were obtained with good relative standard deviations (<5%), leading to low LODs (0.001-0.011 ng L^-1) and LOQs (0.004-0.036 ng L^-1). Good accuracy of this method was validated by two certified reference materials of total lead in water (GBW08601) and total mercury in water (GBW08603) along with spiked recoveries (89-93%). The method was applied to analyze trace lead and mercury species in river, lake, tap and rain water, and purified and mineral water. Inorganic lead of 13-68 ng L^-1 and inorganic mercury of 21-49 ng L^-1 were measured in the nine water samples whereas TML, TEL and MeHg were not detected with 2-5 ng L^-1 EtHg presented only in one river water and tap water.

Development of comprehensive two-dimensional low-flow liquid-chromatography setup coupled to high-resolution mass spectrometry for shotgun proteomics

Bottom-up proteomics provides often small amounts of highly complex samples that cannot be analysed by direct mass spectrometry (MS). To gain a better insight in the sample composition, liquid chromatography (LC) and (comprehensive) two-dimensional liquid chromatography (2D-LC or LC × LC) can be coupled to the MS. Low-flow separations are attractive for HRMS analysis, but they tend to be lengthy. In this work, a low-flow, online, actively modulated LC × LC system, based on hydrophilic-interaction liquid chromatography (HILIC) in the first dimension and reversed-phase liquid chromatography (RPLC) in the second dimension, was developed to separate complex mixtures of peptides. Miniaturization permitted the analysis of small sample amounts (1-5 μg) and direct coupling with micro-ESI MS (1 μL min^-1). All components were focused and automatically transferred from HILIC to RPLC using stationary-phase-assisted active modulation (C18 traps) to deal with solvent-incompatibility or dilution issues. Optimization of the setup was performed for the HILIC columns and the RPLC columns to provide a more efficient separation and higher identification rates than obtained using one-dimensional (1D) LC. A 60% increase in peak capacity was obtained with the 2D setup compared to a 1D-RPLC separation and a 17-34% increase in the number of proteins identified was achieved for the samples analysed (2D-yeast-8280 peptides and 2D-kidney tissue-8843 peptides), without increasing the analysis time (2 h).

The influence of injection volume on efficiency of microbore liquid chromatography columns for gradient and isocratic elution

The injection volume and the associated column volume overload is one of the most common issues in miniaturized chromatography. The injection volume should not exceed 10% of the effective column volume. A further reduction of the injection volume leads to an increase in chromatographic efficiency. However, the signal intensity must be above a certain threshold to generate a chromatographic peak that can be detected. Therefore, the injection volume has to be optimized to reach the ideal balance between chromatographic efficiency and sensitivity. This study examined the general influence of the injection volume for both isocratic and gradient elution, depending on the retention factor and peak standard deviation. For this purpose, substances of different polarity were selected to represent a broad elution spectrum. Besides the model analyte naphthalene, these were mainly pharmaceuticals. For all measurements a microbore column with an ID of 300 µm and packed with 1.9 μm fully porous particles was used. For isocratic elution, the injection volume was varied between 4 and 16% of the effective column volume. The retention factors were adjusted between 2 and 10. For gradient elution, the injection volume was varied between 4 and 160% of the effective column volume. The observed effects were further investigated using the gradient kinetic plot theory. In isocratic elution, a loss in plate height up to 50% was observed for components that elute near the void time. A significant reduction of the chromatographic efficiency was noticed up to a retention factor of 4. In gradient elution, a reduction in peak capacity could only be observed if the injection volume exceeded 40% of the effective column volume. For some substances, only a slight loss in peak capacity was noticed even with a volume overload of 160%.

The theory and practice of ultrafast liquid chromatography: A tutorial

Modern high-throughput experimentation and challenging analytical problems of academic/industrial research have put the responsibility on separation scientists to develop new fast separation approaches. With the availability of high-pressure pumps, small particles with hydrolytically stable surface chemistries, reduced extra-column band broadening, and low volume detectors with fast signal processing, it is now feasible to do sub-minute to sub-second chromatography. Herein, the fundamental theoretical principles of ultrafast chromatography, along with practical solutions, are reviewed. Approaches for rapid separations in packed beds, narrow open tubular columns, and monoliths are demonstrated, along with the challenges that were faced. The instrumentation requirements (pumps, injection systems, detectors, column packing process) for using short columns ranging from 0.5 to 5 cm are examined, followed by real applications. One of the main problems in ultrafast chromatography is partial or complete peak overlap. As per Gidding's statistical overlap theory, peak overlap cannot be avoided for a completely random sample for a column with a given peak capacity. Signal processing techniques based on Fourier transform deconvolution of band broadening, power laws, derivatives, and iterative curve fitting are explained to help improve the chromatographic resolution. An example of ten peaks separated in under a second is shown and discussed. Other ultrafast separations in supercritical fluid chromatography or capillary electrophoresis are briefly mentioned to provide a complete understanding of this emerging field.

Capillary ultrahigh-pressure liquid chromatography-mass spectrometry for fast and high resolution metabolomics separations

LC-MS is an important tool for metabolomics due its high sensitivity and broad metabolite coverage. The goal of improving resolution and decreasing analysis time in HPLC has led to the use of 5 - 15 cm long columns packed with 1.7 - 1.9 µm particles requiring pressures of 8 - 12 kpsi. We report on the potential for capillary LC-MS based metabolomics utilizing porous C18 particles down to 1.1 µm diameter and columns up to 50 cm long with an operating pressure of 35 kpsi. Our experiments show that it is possible to pack columns with 1.1 µm porous particles to provide predicted improvements in separation time and efficiency. Using kinetic plots to guide the choice of column length and particle size, we packed 50 cm long columns with 1.7 µm particles and 20 cm long columns with 1.1 µm particles, which should produce equivalent performance in shorter times. Columns were tested by performing isocratic and gradient LC-MS analyses of small molecule metabolites and extracts from plasma. These columns provided approximately 100,000 theoretical plates for metabolite standards and peak capacities over 500 in 100 min for a complex plasma extract with robust interfacing to MS. To generate a given peak capacity, the 1.1 µm particles in 20 cm columns required roughly 75% of the time as 1.7 µm particles in 50 cm columns with both operated at 35 kpsi. The 1.1 µm particle packed columns generated a given peak capacity nearly 3 times faster than 1.7 µm particles in 15 cm columns operated at ~10 kpsi. This latter condition represents commercial state of the art for capillary LC. To consider practical benefits for metabolomics, the effect of different LC-MS variables on mass spectral feature detection was evaluated. Lower flow rates (down to 700 nL/min) and larger injection volumes (up to 1 µL) increased the features detected with modest loss in separation performance. The results demonstrate the potential for fast and high resolution separations for metabolomics using 1.1 µm particles operated at 35 kpsi for capillary LC-MS.

Nano-liquid chromatography-mass spectrometry and recent applications in omics investigations

Liquid chromatography coupled to mass spectrometry (LC-MS) is one of the most powerful tools in identifying and quantitating molecular species. Decreasing column diameter from the millimeter to micrometer scale is now a well-developed method which allows for sample limited analysis. Specific fabrication of capillary columns is required for proper implementation and optimization when working in the nanoflow regime. Coupling the capillary column to the mass spectrometer for electrospray ionization (ESI) requires reduction of the subsequent emitter tip. Reduction of column diameter to capillary scale can produce improved chromatographic efficiency and the reduction of emitter tip size increased sensitivity of the electrospray process. This improved sensitivity and ionization efficiency is valuable in analysis of precious biological samples where analytes vary in size, ion affinity, and concentration. In this review we will discuss common approaches and challenges in implementing nLC-MS methods and how the advantages can be leveraged to investigate a wide range of biomolecules.

Miniaturized liquid chromatography applied to the analysis of residues and contaminants in food: A review

The humankind is pretty dependent on food to control several biological processes into the organism. As the world population increases, the demand for foodstuffs follows the same trend claiming for a high food production situation. For this reason, a substantial amount of chemicals is used in agriculture and livestock husbandries every year, enhancing the likelihood of contaminated foodstuffs being commercialized. This outlook becomes a public health concern; thus, the governmental regulatory agencies impose laws to control the residues and contaminants in food matrices. Currently, one of the most important analytical techniques to perform it is LC. Despite its already recognized effectiveness, it is often time consuming and requires significant volumes of reagents, which are transformed into toxic waste. In this context, miniaturized LC modes emerge as a greener and more effective analytical technique. They have remarkable advantages, including higher sensitivity, lower sample amount, solvent and stationary phase requirements, and more natural coupling to MS. In this review, most of the critical characteristics of them are discussed, focusing on the benchtop instruments and their related analytical columns. Additionally, a discussion regarding the last 10 years of publications reporting miniaturized LC application for the analysis of natural and industrial food samples is categorized. The main chemical classes as applied in the crops are highlighted, including pesticides, veterinary drugs, and mycotoxins.

Ultrahigh-Performance capillary liquid chromatography-mass spectrometry at 35 kpsi for separation of lipids

Improvements in sample preparation, separation, and mass spectrometry continue to expand the coverage in LC-MS based lipidomics. While longer columns packed with smaller particles in theory give higher separation performance compared to shorter columns, the implementation of this technology above commercial limits has been sparse due to difficulties in packing long columns and successfully operating instruments at ultrahigh pressures. In this work, a liquid chromatograph that operates up to 35 kpsi was investigated for the separation and identification of lipid species from human plasma. Capillary columns between 15-50 cm long were packed with 1.7 µm BEH C18 particles and evaluated for their ability to separate lipid isomers and complex lipid extracts from human plasma. Putative lipid class identifications were assigned using accurate mass and relative retention time data of the eluting peaks. Our findings indicate that longer columns packed and operated at 35 kpsi outperform shorter columns packed and run at lower pressures in terms of peak capacity and numbers of features identified. Packing columns with relatively high concentration slurries (200 mg/mL) while sonicating the column resulted in 6-34% increase in peak capacity for 50 cm columns compared to lower slurry concentrations and no sonication. For a given analysis time, 50 cm long columns operated at 35 kpsi provided a 20-95% increase in chromatographic peak capacity compared with 15 cm columns operated at 15 kpsi. Analysis times up to 4 h were evaluated, generating peak capacities up to 410 ± 5 (n = 3, measured at 4σ) and identifying 480 ± 85 lipids (n = 2). Importantly, the results also show a correlation between the peak capacity and the number of lipids identified from a human plasma extract. This correlation indicates that ionization suppression is a limiting factor in obtaining sufficient signal for identification by mass spectrometry. The result also shows that the higher resolution obtained by shallow gradients overcomes possible signal reduction due to broader, more dilute peaks in long gradients for improving detection of lipids in LC-MS. Lastly, longer columns operated at shallow gradients allowed for the best separation of both regional and geometrical isomers. These results demonstrate a system that enables the advantages of using longer columns packed and run at ultrahigh pressure for improving lipid separations and lipidome coverage.

Liquid chromatography above 20,000 PSI

Continued improvements in HPLC have led to faster and more efficient separations than previously possible. One important aspect of these improvements has been the increase in instrument operating pressure and the advent of ultrahigh pressure LC (UHPLC). Commercial instrumentation is now capable of up to ~20 kpsi, allowing fast and efficient separations with 5-15 cm columns packed with sub-2 μm particles. Home-built instruments have demonstrated the benefits of even further increases in instrument pressure. The focus of this review is on recent advancements and applications in liquid chromatography above 20 kpsi. We outline the theory and advantages of higher pressure and discuss instrument hardware and design capable of withstanding 20 kpsi or greater. We also overview column packing procedures and stationary phase considerations for HPLC above 20 kpsi, and lastly highlight a few recent applicatioob pressure instruments for the analysis of complex mixtures.

Enhancing the selectivity of polar hydrophilic analytes with a low concentration of barium ions in the mobile phase using geopolymers and silica supports

Charged analytes such as organic sulfonic acids, sulfates, carboxylates, and phosphates are often analyzed by hydrophilic interaction liquid chromatography (HILIC). In many cases, these analytes do not show any selectivity and elute near the dead time using the conventional acetonitrile-ammonium acetate buffers. In this work, we introduce a powerful selectivity enhancing technique by using a trace amount of Ba²⁺ ion in the mobile phase as a general approach for HILIC with UV-Vis detection. Silica and a newly developed material called geopolymers are used as stationary phases. Geopolymers are X-ray amorphous aluminosilicate inorganic polymers with cation exchange properties. Barium exchanged geopolymers (Ba-NM-GP) are synthesized from metakaolin based geopolymer. Thorough characterization of Ba-NM-GP is reported using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Brunauer-Emmett-Teller (BET) surface area analyzer and laser diffraction particle size distribution analyzer for the determination of their shape, size, porosity, surface area and particle size distribution respectively. It is demonstrated that in the absence of Ba²⁺, baseline separations of sulfonates, carboxylates, and phosphates is not possible, whereas, in the presence of Ba²⁺ in the mobile phase, these analytes are easily separated. Barium perchlorate is suggested as an additive for it is UV transparent, and it has practically an unlimited solubility in acetonitrile.

Identification and Quantification of Proteoforms by Mass Spectrometry

A proteoform is a defined form of a protein derived from a given gene with a specific amino acid sequence and localized post-translational modifications. In top-down proteomic analyses, proteoforms are identified and quantified through mass spectrometric analysis of intact proteins. Recent technological developments have enabled comprehensive proteoform analyses in complex samples, and an increasing number of laboratories are adopting top-down proteomic workflows. In this review, some recent advances are outlined and current challenges and future directions for the field are discussed.

The utility of statistical moments in chromatography using trapezoidal and Simpson's rules of peak integration

Modern chromatographic data acquisition softwares often behave as black boxes where the researchers have little control over the raw data processing. One of the significant interests of separation scientists is to extract physico-chemical information from chromatographic experiments and peak parameters. In addition, column developers need the total peak shape analysis to characterize the flow profile in chromatographic beds. Statistical moments offer a robust approach for providing detailed information for peaks in terms of area, its center of gravity, variance, resolution, and its skew without assuming any peak model or shape. Despite their utility and theoretical significance, statistical moments are rarely incorporated as they often provide underestimated or overestimated results because of inappropriate choice of the integration method and selection of integration limits. The Gaussian model is universally used in most chromatography softwares to assess efficiency, resolution, and peak position. Herein we present a user-friendly, and accessible approach for calculating the zeroth, first, second, and third moments through more accurate numerical integration techniques (Trapezoidal and Simpson's rule) which provide an accurate estimate of peak parameters as compared to rectangular integration. An Excel template is also provided which can calculate the four moments in three steps with or without baseline correction.

New Brush-Type Chiral Stationary Phases for Enantioseparation of Pharmaceutical Drugs

The importance of chirality in drug development is unquestionable, with chiral liquid chromatography (LC) being the most adequate technique for its analysis. Among the various types of chiral stationary phases (CSPs) for LC, brush-type CSPs provide the base for interaction analysis of CSPs and enantiomers, which provide valuable results that can be applied to interaction studies of other CSP types. In order to analyze the influence of aromatic interactions in chiral recognition, we designed a set of ten new brush-type CSPs based on (S)-N-(1-aryl-propyl)-3,5-dinitrobenzamides which differ in the aromatic unit directly linked to the chiral center. Thirty diverse racemates, including several nonsteroidal anti-inflammatory drugs and 3-hydroxybenzodiazepine drugs, were used to evaluate the prepared CSPs. Chromatographic analysis showed that the three new CSPs separate enantiomers of a wide range of compounds and their chromatographic behavior is comparable to the most versatile brush-type CSP—Whelk-O1. The critical role of the nonbonding interactions in positioning of the analyte (naproxen) in the cleft of CSP-6, as well as the analysis of interactions that make enantioseparation possible, were elucidated using computational methods. Furthermore, the influence of acetic acid as a mobile phase additive, on this enantiorecognition process was corroborated by calculations.

FlashPack: Fast and Simple Preparation of Ultrahigh-performance Capillary Columns for LC-MS

Capillary ultrahigh-pressure liquid chromatography (cUHPLC) is essential for in-depth characterization of complex biomolecule mixtures by LC-MS. We developed a simple and fast method called FlashPack for custom packing of capillary columns of 50-100 cm length with sub- 2 μm sorbent particles. FlashPack uses high sorbent concentrations of 500-1,000 mg/ml for packing at relatively low pressure of 100 bar. Column blocking by sorbent aggregation is avoided during the packing by gentle mechanical tapping of the capillary proximal end by a slowly rotating magnet bar. Utilizing a standard 100-bar pressure bomb, Flashpack allows for production of 15-25 cm cUHPLC columns within a few minutes and of 50 cm cUHPLC columns in less than an hour. Columns exhibit excellent reproducibility of back-pressure, retention time, and resolution (CV 8.7%). FlashPack cUHPLC columns are inexpensive, robust and deliver performance comparable to commercially available cUHPLC columns. The FlashPack method is versatile and enables production of cUHPLC columns using a variety of sorbent materials.

Detailed efficiency analysis of columns with a different packing quality and confirmation via total pore blocking

We report on a systematic study involving columns with a clearly different efficiency (4 distinct quality groups) obtained by packing the columns that were C₁₈ bonded and endcapped with a different carbon loading. Using B-term analysis (via peak parking) and theoretical models to estimate the magnitude of the C_m- and C_s-term contributions, it could be concluded that the difference in efficiency among the groups was entirely due to a difference in eddy dispersion. As such, the columns provided an ideal testing ground to verify how well the total pore blocking (TPB)-method can be used to probe differences in packing heterogeneity. In agreement with earlier literature observations, it turns out the TPB-method is much more sensitive to packing heterogeneities than the eddy dispersion (H_eddy)-contribution measured under open-pore conditions via B- and C- term subtraction. Typically, differences in H_eddy on the order of 0.1-0.5μm translate into a difference on the order of 0.5-2μm in the TPB mode. This confirms the TPB as a powerful technique to make very sensitive measurements of the homogeneity of packed beds.

Ultra-High Pressure (>30,000 psi) Packing of Capillary Columns Enhancing Depth of Shotgun Proteomic Analyses

Extreme sample complexity is an inherent challenge in shotgun proteomics that positions quality of chromatographic separations as one of the key determinants of attainable proteome coverage. In search of better separations, macroscopic physical characteristics of capillary columns, i.e., length and properties of stationary phase particles, are typically considered and optimized, while significance of packing bed morphology is frequently underappreciated. Here, we describe a technology that enables packing of capillary columns at excess of 30,000 psi and demonstrate that such columns exhibit reduced backpressure and remarkably reproducible chromatographic performance, improved on average by 23%. These enhancements afford up to 35% increase in the depth of commonplace bottom-up proteomic analyses, owning to augmented sensitivity and resolution of peptide separations and improvements in spectral quality. Our findings strongly corroborate advantages of ultra-high pressure packing of capillary columns for diverse shotgun proteomic workflows.