How Catalysts and Experimental Conditions Determine the Selective Hydroconversion of Furfural and 5-Hydroxymethylfurfural

Heteropolyacid promoted lignin-MOF derived spherical catalyst for catalytic hydrogen transfer of 5-hydroxymethylfurfural

Catalytic conversion of biomass-derived value-added chemicals was of great significance for the utilization of renewable biomass resources to instead of fossil chemicals. Biomass-derived lignin was regarded as an important support and 5-hydroxymethylfurfural (HMF) was a vital platform chemical derived from cellulose. Herein, a series of lignin-MOF hybrid catalysts were prepared and modified with different heteropolyacids (HPAs), which were then successfully introduced into the selective conversion of HMF to 5-hydroxymethylfurfuryl alcohol (MFA). The effect of different HPA, calcination temperature, etc. were all studied, and all catalysts were well characterized. It was confirmed that silicotungstic acid modified catalyst (Ni3Co-MOF-LS@HSiW) exhibited the best catalytic performance, while the highest conversion of HMF was up to 100%, with the best MFA yield of 86.5%. The finding in this study could provide novel insights for the utilization of lignin and preparation of value-added biomass-derived chemicals.

5-Hydroxymethylfurfural and its Downstream Chemicals: A Review of Catalytic Routes

Biomass assumes an increasingly vital role in the realm of renewable energy and sustainable development due to its abundant availability, renewability, and minimal environmental impact. Within this context, 5-hydroxymethylfurfural (HMF), derived from sugar dehydration, stands out as a critical bio-derived product. It serves as a pivotal multifunctional platform compound, integral in synthesizing various vital chemicals, including furan-based polymers, fine chemicals, and biofuels. The high reactivity of HMF, attributed to its highly active aldehyde, hydroxyl, and furan ring, underscores the challenge of selectively regulating its conversion to obtain the desired products. This review highlights the research progress on efficient catalytic systems for HMF synthesis, oxidation, reduction, and etherification. Additionally, it outlines the techno-economic analysis (TEA) and prospective research directions for the production of furan-based chemicals. Despite significant progress in catalysis research, and certain process routes demonstrating substantial economics, with key indicators surpassing petroleum-based products, a gap persists between fundamental research and large-scale industrialization. This is due to the lack of comprehensive engineering research on bio-based chemicals, making the commercialization process a distant goal. These findings provide valuable insights for further development of this field.

Acid-Catalyzed Activation and Condensation of the =C5H Bond of Furfural on Aldehydes, an Entry Point to Biobased Monomers

Furfural is an industrially relevant biobased chemical platform. Unlike classical furan, or C-alkylated furans, which have been previously described in the current literature, the =C5H bond of furfural is unreactive. As a result, on a large scale, C=C and C=O bond hydrogenation/hydrogenolysis is mainly performed, with furfuryl alcohol and methyl tetrahydrofuran being the two main downstream chemicals. Here, we show that the derivatization of the -CHO group of furfural restores the reactivity of its =C5H bond, thus permitting its double condensation on various alkyl aldehydes. Overcoming the recalcitrance of the =C5H bond of furfural has opened an access to a biobased monomer, whose potential have been investigated in the fabrication of renewably-sourced poly(silylether). By means of a combined theoretical-experimental study, a reactivity scale for furfural and its protected derivatives against carbonylated compounds has been established using an electrophilicity descriptor, a means to predict the molecular diversity and complexity this pathway may support, and also to de-risk any project related to this topic. Finally, by using performance criteria for industrial operations in the field of fuels and commodities, we discussed the industrial potential of this work in terms of cost, E-factor, reactor productivity and catalyst consumption.

Steering Selectivity in Electrocatalytic Furfural Reduction via Electrode-Electrolyte Interface Modification

Electrocatalytic reduction of biomass-derived furfural (FF) represents a sustainable route to produce furfuryl alcohol (FA) and 2-methylfuran (MF) as a value-added chemical and a biofuel, respectively. However, achieving high selectivity for MF as well as tuning the selectivity between FA and MF within one reaction system remain challenging. Herein, we have reported an electrode-electrolyte interface modification strategy, enabling FA and MF selectivity steering under the same reaction conditions. Specifically, by modifying copper (Cu) electrocatalysts with butyl trimethylammonium bromide (BTAB), we achieved a dramatic shift in selectivity from producing FA (selectivity: 83.8%; Faradaic efficiency, FE: 68.9%) to MF (selectivity: 80.1%; FE: 74.8%). We demonstrated that BTAB adsorption over Cu modulates the electrical double layer (EDL) structure, which repels interfacial water and weakens the hydrogen-bond (H-bond) network for proton transfer, thus impeding FF-to-FA conversion by suppression of the hydrogen atom transfer (HAT) process. On the contrary, FF-to-MF conversion was less affected. This work shows the potential of engineering of the electrode-electrolyte interface for selectivity control in electrocatalysis.

Strengthening the Metal-Acid Interactions by Using CeO2 as Regulators of Precisely Placing Pt Species in ZSM-5 for Furfural Hydrogenation

Understanding the synergism between the metal site and acid site is of great significance in boosting the efficiency of bi-functional catalysts in many heterogeneous reactions, particularly in biomass upgrading. Herein, a "confined auto-redox" strategy is reported to fix CeO2-anchored Pt atoms on the inner wall of a ZSM-5 cage, achieving the target of finely controlling the placements of the two active sites. Compared with the conventional surface-supported counterpart, the encapsulated Pt/CeO2@ZSM-5 catalyst possesses remarkably-improved activity and selectivity, which can convert >99% furfural into cyclopentanone with 97.2% selectivity in 6 h at 160 °C. Besides the excellent catalytic performance, the ordered metal-acid distribution also makes such kind of catalyst an ideal research subject for metal-acid interactions. The following mechanization investigation reveals that the enhancement is strongly related to the unique encapsulation structure, which promotes the migration of the reactants over different active sites, thereby contributing to the tandem reaction.

Noble-Metal-Free Carbon Encapsulated CoNi Alloy Catalyst for the Hydrogenation of 5-(Hydroxymethyl) Furfural to Tetrahydrofurandiol in Aqueous Media

The selective hydrogenation of 5-(hydroxymethyl)furfural (HMF) into 2,5-bis-(hydroxymethyl)tetrahydrofuran (BHMTHF) in flow reactor using water as a green solvent, has been achieved on a non-noble metal catalyst based on monodispersed CoNi alloy nanoparticles covered by a thin carbon layer. The alloyed catalyst containing CoNi (molar ratio 1 : 1) was prepared in a one-step synthesis following a hydrothermal method. Total conversion of HMF with 91 % selectivity to BHMTHF was achieved. The reaction network has been stablished, in which the carbonyl group of HMF is first reduced to alcohol giving the 2,5-bis-(hydroxymethyl)furan (BHMF) with an apparent activation energy of 25 KJ/mol, and then the double bonds of the furan ring are hydrogenated (apparent Ea=31 KJ/mol). Formation of byproducts, mainly proceed from furan ring opening and ring rearrangement processes of BHMF, promoted by water. BHMTHF resulted a compound highly stable under reaction conditions. The fixed bed flow reactor was maintained operational for 65 h without observing any loss of catalytic activity and selectivity.

Electron-Rich Ru Supported on N-Doped Coffee Biochar for Selective Reductive Amination of Furfural to Furfurylamine

Highly selective synthesis of primary amines from renewable biomass has attracted increasing attention, but it still faces great challenges in chemical industry applications. In this study, an electron-rich Ru catalyst was constructed by doping N into coffee biochar using a one-pot carbonization method (Ru/NCB-600). Ru/NCB-600 showed high catalytic activity and yield for the reductive amination of furfural with green and cheap NH3 and H2. The excellent catalytic performance of Ru/NCB-600 was closely correlated to the formation of electron-rich Ruδ- species (Ruδ--Nxδ+), which endowed Ru/NCB-600 with an enhanced H2 adsorption and activation ability. Ru/NCB-600 showed a high formation rate of 95.6 gfurfurylamine·gRu-1·h-1 and a high yield of furfurylamine (98.6%) at 50 °C. Ru/NCB-600 can also be used for the reductive amination of various carbonyl compounds in good to excellent yield (95.4-99%). This study thus provides a potential pathway for the highly selective reductive amination of carbonyl compounds by regulating the electron density of Ru.

Tailoring the Brønsted acidity of Ti-OH species by regulating Pt-TiO2 interaction

Bifunctional catalysts comprising metal and acid sites are commonly used for many reactions. Interfacial acid sites impact intermediate reactions more than other sites. However, controlling the type and amounts of interfacial acid sites by regulating metal-support interaction (MSI) via traditional methods is difficult. Thus, the influence of MSI on interfacial acid sites remains unclear. We prepared Pt-mTiO2/α-Al2O3 (m represents the cycle number of TiO2) catalysts via atomic layer deposition (ALD). New Brønsted acid sites were generated via Pt-TiO2 interaction, and the acidity was precisely regulated by regulating Pt-TiO2 interaction by changing the TiO2 nanolayer thickness. We chose levulinic acid (LA) hydrogenation as a model reaction. The catalytic activity varied with the TiO2 nanolayer thickness and was linearly correlated with the Ti-OH species (Brønsted acid) content. Pt-40TiO2/α-Al2O3, with the highest acid site content of 0.486 mmol/g, exhibited the best catalytic activity. Hydrogen spillover and water dissociation at the Pt-TiO2 interface promoted Ti-OH species generation.

Graphene Chainmail Shelled Dilute Ni─Cu Alloy for Selective and Robust Aqueous Phase Catalytic Hydrogenation

Cost-effective non-noble metal-based catalysts for selective hydrogenation with excellent activity, selectivity, and durability are still the holy grail. Herein, an oxygen-doped carbon (OC) chainmail encapsulated dilute Cu-Ni alloy is developed by simple pyrolysis of Cu/Ni-metal-organic framework. The CuNi0.05@OC catalyst displays superior performance for atmospheric pressure transfer hydrogenation of p-chloronitrobenzene and p-nitrophenol, and for hydrogenation of furfural, all in water and with exceptional durability. Comprehensive characterizations confirm the close interactions between the diluted Ni sites, the base Cu, and optimized three-layered graphene chainmail. Theoretical calculations demonstrate that the properly tuned lattice strain and Schottky junction can adjust electron density to facilitate specific adsorption on the active centers, thus enhancing the catalytic activity and selectivity, while the OC shell also offers robust protection. This work provides a simple and environmentally friendly strategy for developing practical heterogeneous catalysts that bring the synergistic effect into play between dilute alloy and functional carbon wrapping.

Strategies to improve hydrogen activation on gold catalysts

Catalytic reactions involving molecular hydrogen are at the heart of many transformations in the chemical industry. Classically, hydrogenations are carried out on Pd, Pt, Ru or Ni catalysts. However, the use of supported Au catalysts has garnered attention in recent years owing to their exceptional selectivity in hydrogenation reactions. This is despite the limited understanding of the physicochemical aspects of hydrogen activation and reaction on Au surfaces. A rational design of new improved catalysts relies on making better use of the hydrogenating properties of Au. This Review analyses the strategies utilized to improve hydrogen-Au interactions, from addressing the importance of the Au particle size to exploring alternative mechanisms for H2 dissociation on Au cations and Au-ligand interfaces. These insights hold the potential to drive future applications of Au catalysis.

Enhancing Low-Potential Electrosynthesis of 2,5-Furandicarboxylic Acid on Monolithic CuO by Constructing Oxygen Vacancies

Electrosynthesis of 2,5-furandicarboxylic acid (FDCA) from the biomass-derived 5-hydroxymethylfurfural (HMF) is one of the most potential means to produce a bioplastic monomer. Copper oxide (CuO) catalyst shows promising prospects due to its high surface activity, conductivity, and stability, but relatively poor capability of oxygen evolution; however, the weak adsorption of substrates and the lack of facile synthetic strategies largely restrict its practical application. Here, a novel facile in situ method, alternate cycle voltammetry (denoted as c) and potentiostatic electrolysis (denoted as p), was proposed to prepare a monolithic cpc-CuO/Cu-foam electrocatalyst. Along with the increment of CuO and its surficial oxygen vacancies (OV), the FDCA yield, productivity, and Faradaic efficiency can reach up to ∼98.5%, ∼0.2 mmol/cm2, and ∼94.5% under low potential of 1.404 VRHE. Such an efficient electrosynthesis system can be easily scaled up to afford pure FDCA powders. In a combinatory analysis via electron paramagnetic resonance spectroscopy, H2 temperature-programmed reduction, open circuit potential, infrared spectroscopy, zeta potential, electrochemical measurement, and theoretical calculation, we found that the CuO was the active phase and OV generated on CuO surface can dramatically enhance the adsorption of *HMF and *OH (* denotes an active site), accounting for its superior FDCA production. This work offers an excellent paradigm for enhancing biomass valorization on CuO catalysts by constructing surficial defects.

Selective Electroreduction of 5-Hydroxymethylfurfural to Dimethylfuran in Neutral Electrolytes via Hydrogen Spillover and Adsorption Configuration Adjustment

5-Hydroxymethylfurfural (HMF), one of the essential C6 biomass derivatives, has been deeply investigated in electrocatalytic reduction upgrading. Nevertheless, the high product selectivity and rational design strategy of electrocatalysts for electrocatalytic HMF reduction is still a challenge. Here, a high selective electro-reduction of HMF to dimethylfuran (DMF) on palladium (Pd) single atom loaded on titanium dioxide (Pd SA/TiO2 ) via hydrogen spillover and adsorption configuration adjustment in neutral electrolytes is achieved. Combining density functional theory calculations and in situ characterization, it is revealed that Pd single atom could weaken the interaction between Pd atoms and adsorbed hydrogen (*H) to promote the *H spillover for increasing *H coverage on the surface and maintain the tilted adsorption configuration to activate C═O bond; thus the selectivity of DMF on Pd SA/TiO2 increases to 90.33%. Besides, it is elaborated that low *H coverage on TiO2 favors the formation of bis(hydroxymethyl)hydro-furoin (BHH), and the flat adsorption configuration of HMF on Pd nanoparticles benefits to form 2,5-dihydroxymethylfuran (DHMF). This work provides a promising approach for modifying electrocatalysts to realize the selective electroreduction of HMF to value-added products.

Heterogeneously catalyzed decarbonylation of thioesters by supported Ni, Pd, or Rh nanoparticle catalysts

Decarbonylation of thioesters has been actively studied using homogeneous metal catalysts as an attractive approach for synthesizing thioethers, which are widely utilized in various fields, because decarbonylation ideally requires no additives and produces CO as the sole theoretical byproduct. However, heterogeneously catalyzed decarbonylation of thioesters has not been reported to date, despite its importance for the construction of environmentally-friendly and practical catalytic systems. This study demonstrated a heterogeneously catalyzed system for the decarbonylation of various aryl thioesters to produce thioethers and CO by utilizing CeO2- or hydroxyapatite-supported Ni, Pd, or Rh nanoparticle catalysts. The Ni catalysts showed high catalytic activity, while the Pd catalysts possessed excellent functional group tolerance. The Rh catalysts were suitable for the selective decarbonylation of unsymmetrically substituted thioesters.

Understanding the Role of Base Species on Reversed Cu Catalyst in Ring Opening of Furan Compounds to 1, 2-Pentanediol

The hydrogenation of biomass-derived furan compounds provides a sustainable pathway for the production of various valuable chemicals; product selectivity among multiple reaction pathways of furan compound hydrogenation is crucially dependent on catalytic sites; however controlling reaction pathways remains challenging due to the lack of identification and understanding of active sites. In this work we reveal the role of base sites in furfural selective hydrogenation through deliberately designed and synthesized reversed catalysts, basic metal oxides and hydroxide on Cu. It is demonstrated that base species greatly enhanced the selectivity of 1, 2-pentanediol (1, 2-PeD) from furfural, presenting a nearly fourfold increase of 1, 2-PeD: methyl furan ratio over the Cu based reverse catalysts. A combination of infrared spectroscopy and DFT calculations demonstrates the strong interaction between the C-O-C bond in furan ring and the catalyst surface in preferentially parallel adsorption mode in the presence of base species on Cu, thus facilitating the activation of C-O-C bond to produce 1, 2-PeD. This work provides a strategy of designing reversed catalyst to study the effect of promoters and reveals the role of base sites in the hydrogenation of biomass-derived furan compounds to diols.

Gas-phase hydrogenation of furfural into value-added chemicals: The critical role of metal-based catalysts

Furfural (FF: aldehyde derivable from lignocellulosic biomass) has been widely recognized as a versatile building block for eco-friendly and sustainable applications to reduce industrial reliance on fossil-fuel carbon sources. Hydrogenation of FF, in particular, is recognized as one of the most effective routes for producing various value-added chemicals (e.g., furfuryl alcohol and 2-methylfuran). The gas-phase FF hydrogenation reaction offers economic and environmental advantages over its liquid-phase counterpart in conversion efficiency, product selectivity, and kinetics. The operation of the former does not require high hydrogen pressures or hazardous solvents while not generating undesirable by-products (due to reduced selectivity toward the ring-opening reaction). In this context, the utility of noble and non-noble metal catalyst systems has been recognized for their potential to induce effective FF hydrogenation in the gas phase. The present review addresses current understandings and recent developments in research on gas-phase FF hydrogenation and the factors governing the performance of metal-based catalysts (e.g., materials and surface chemistry; conversion efficiency; product selectivity; and the mechanisms, pathways, and kinetics of the associated reactions). Current shortcomings and research avenues are also discussed to help establish a roadmap for future development of the gas-phase FF hydrogenation technology and associated disciplines. Overall, the present review is expected to offer much-needed insights into the scalability of metal-based catalytic systems for efficient FF hydrogenation in the gas phase.

Hydrogenation of levulinic acid to γ-valerolactone over hydrophobic Ru@HCP catalysts

This study introduces an efficient strategy for promoting the synthesis of γ-valerolactone (GVL) via levulinic acid (LA) hydrogenation. A series of hyper-crosslinked porous polymer (HCP) supported Ru catalysts with different monomers were prepared. The wettabilities were controlled by the surface functional groups. The hydrophobic catalysts showed much higher activity than the hydrophilic ones in the hydrogenation of LA to GVL, highly possible due to the substrate enrichment. Further insight showed that the reaction proceeded through the 4-HVA route. These results illustrated the importance of surface wettability in bio-based molecule upgrading, which is beneficial for catalyst design.

CH bond activation in aromatic ketones mediated by iridium-tris(pyrazolyl)borate complexes

Reaction of complex [TpMe2Ir(η4-CH2C(Me)C(Me)C2)] (1) with a series of aromatic ketones at 130 °C renders, by means of a selective ortho-CH activation, Ir(III)-metallacycles 2-5, which display an Ir-H bond. When [TpMe2Ir(C6H5)2N2] (6) is treated with 2-(trifluoromethyl)acetophenone and 2-fluoroacetophenone at 80 °C, the formation of dimeric (7) and trimeric architectures (8) is achieved through the meta- and para-CH activation of the aromatic ketone, respectively. The generation of complexes 2-5 is proposed to occur by the initial formation of Ir(III) η1-ketone adducts as key intermediates, followed by aromatic CH activations and the release of a butadiene ligand. The formation of complexes 7 and 8 involves an assisted process in which a metal center activation of the less sterically hindered C-H bond of the aromatic ketone takes place (releasing a benzene molecule), followed by the coordination of the carbonyl group, which generates the respective dimeric and trimeric structures. Complexes 7 and 8 are efficient catalysts for the transfer hydrogenation of ketones and aldehydes using isopropanol as the hydrogen source. All complexes have been fully characterized by NMR spectroscopy, FT-IR, elemental analysis and, in the cases of 7 and 8, X-ray crystallography. Details of the reaction conditions, isolation of the products, and proposals for the pathways of formation of complexes 2-5 and 7-8 are discussed.

Plasma-Enabled Ligand Removal for Improved Catalysis: Furfural Conversion on Pd/SiO2

A nonthermal, atmospheric He/O2 plasma (NTAP) successfully removed polyvinylpyrrolidone (PVP) from Pd cubic nanoparticles supported on SiO2 quickly and controllably. Transmission electron microscopy (TEM) revealed that the shape and size of Pd nanoparticles remain intact during plasma treatment, unlike mild calcination, which causes sintering and polycrystallinity. Using Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS), we demonstrate the quantitative estimation of the PVP plasma removal rate and control of the nanoparticle synthesis. First-principles calculations of the XPS and CO FTIR spectra elucidate electron transfer from the ligand to the metal and allow for estimates of ligand coverages. Reactivity testing indicated that PVP surface crowding inhibits furfural conversion but does not alter furfural selectivity. Overall, the data demonstrate NTAP as a more efficient method than traditional calcination for organic ligand removal in nanoparticle synthesis.

Biorenewable Oxypropylated Pentane-1,2,5-triol as a Source for Incorporation in Rigid Polyurethane Foams

In this study, as a product from the efficient Achmatowicz rearrangement and mild subsequent hydrogenation-reduction reactions of biorenewable C5 alcohols derived from lignocellulose, pentane-1,2,5-triol was successfully used after oxypropylation in the preparation of rigid polyurethane foams-one of the most important classes of polymeric materials. Despite the broad range of applications, the production of polyurethanes is still highly dependent on petrochemical materials considering the need of renewable raw materials and new process technologies for the production of polyol or isocyanate components as a key point for the sustainable development of polyurethane foams. The synthesized oxypropylated pentane-1,2,5-triol was analyzed using proton NMR spectroscopy, hydroxyl number, and viscosity, whereas the newly obtained foams incorporated with up to 30% biorenewable polyol were characterized using compressive stress, thermogravimetry, dynamic mechanical analysis, and scanning electron microscopy. The modified rigid polyurethanes showed better compressive strength (>400.0 kPa), a comparable thermal degradation range at 325-450 °C, and similar morphological properties to those of commercial polyurethane formulations.

Rh-dispersed Cu nanowire catalyst for boosting electrocatalytic hydrogenation of 5-hydroxymethylfurfural

Electrocatalytic conversion of biomass-derived 5-hydroxymethylfurfural (HMF) to 2,5-bis(hydroxymethyl)furan (BHMF) presents a compelling strategy for the production of premium chemicals via the utilization of renewable energy sources. Exploring efficient catalytic systems to obtain highly selective BHMF has remained a giant challenge. A design strategy is proposed here to regulate active hydrogen (Hads) production in rhodium (Rh) nanoparticles grown on Cu nanowires (RhCu NWs) catalyst, which achieves a faradaic efficiency (FE) of 92.6% in the electrocatalytic reduction of HMF to BHMF at -20 mA cm-2 with no degradation in performance after 8 cycles. Kinetic investigations and electron spin resonance (ESR) spectroscopy reveal that the incorporation of Rh accelerates the water dissociation and facilitates the generation of Hads. In situ attenuated total reflection surface enhanced infrared absorption spectroscopy (ATR-SEIRAS) further demonstrates that the Rh component boosts the proportion of ordered weakly hydrogen-bonded water molecules on the catalyst surface, which is much easier to dissociate. The construction of an interfacial Hads-rich environment promotes the HMF intermediates binding with Hads to BMHF, thereby suppressing the formation of undesired dimers. This work demonstrates the promise of altering the interfacial water environment as a strategy to boost the electrosynthetic properties of biomass-derived products toward value-added outcomes.

Halide Adsorption Enhances Electrochemical Hydrogenolysis of 5-Hydroxymethylfurfural by Suppressing Hydrogenation

Reductive upgrading of 5-hydroxymethylfurfural (HMF), a biomass-derived platform molecule, to 2,5-dimethylfuran (DMF), a biofuel with an energy density 40% greater than that of ethanol, involves hydrogenolysis of both the aldehyde (C═O) and the alcohol (C-OH) groups of HMF. It is known that when hydrogenation of the aldehyde occurs to form 2,5-bis(hydroxymethyl)furan (BHMF), BHMF cannot be further reduced to DMF. Thus, aldehyde hydrogenation must be suppressed to increase the selectivity for DMF production. Previously, it was shown that on a Cu electrode hydrogenolysis occurs mainly through proton-coupled electron transfer (PCET), where a proton from the solution and an electron from the electrode are transferred to the organic species. In contrast, hydrogenation occurs not only through PCET but also through hydrogen atom transfer (HAT), where a surface-adsorbed hydrogen atom (H*) is transferred to the organic species. This study shows that halide adsorption on Cu can effectively suppress HAT by decreasing the steady-state H* coverage on Cu during HMF reduction. As HAT enables only aldehyde hydrogenation, a striking suppression of BHMF is observed, thereby enhancing DMF production. We discuss how the identity and concentration of the halide, along with the reduction conditions (i.e., potential and pH), affect halide adsorption on Cu and identify when optimal halide coverages are achieved to maximize DMF selectivity. Our experimental results are presented alongside computational results that elucidate how halide adsorption affects the adsorption energy of hydrogen and the steady-state H* coverage on Cu, which provide an atomic-level understanding of all experimentally observed effects.

Performance Promotion of Multipurpose Catalysts Using Increased Oxygen Vacancy Amounts by Charge-Mismatched Doping

Modulating the oxygen vacancy (V0) in nanostructures has opened a new avenue for efficient catalyst design, facilitating biomass oxidation reactions and electrocatalytic properties. In this study, we have investigated the properties of NiO-based catalysts with varying degrees of V0 achieved through ion doping of the catalyst with cations of different oxidation states (TM3+) or the same valence state (TM2+) as Ni2+ in the NiO matrix. By introducing charge-mismatched dopants, we enhanced the concentration of V0 in the NiO catalyst, resulting in remarkable selectivity (∼50%) for the conversion of 2,5-hydroxymethylfurfural (HMF) to 2,5-furandicarboxylic acid (FDCA), as well as a lower overpotential in the oxygen evolution reaction (OER). We believe that charge-mismatched doping offers a novel avenue for optimizing defect engineering in oxide-based catalysts, which can enable more efficient biomass conversion and water splitting. These findings have made a significant contribution to the field of multipurpose catalysis and hold the potential to inspire new catalyst designs that would usher in a more sustainable future.

Reduced metal nanocatalysts for selective electrochemical hydrogenation of biomass-derived 5-(hydroxymethyl)furfural to 2,5-bis(hydroxymethyl)furan in ambient conditions

Selective electrochemical hydrogenation (ECH) of biomass-derived unsaturated organic molecules has enormous potential for sustainable chemical production. However, an efficient catalyst is essential to perform an ECH reaction consisting of superior product selectivity and a higher conversion rate. Here, we examined the ECH performance of reduced metal nanostructures, i.e., reduced Ag (rAg) and reduced copper (rCu) prepared via electrochemical or thermal oxidation and electrochemical reduction process, respectively. Surface morphological analysis suggests the formation of nanocoral and entangled nanowire structure formation for rAg and rCu catalysts. rCu exhibits a slight enhancement in ECH reaction performance in comparison to the pristine Cu. However, the rAg exhibits more than two times higher ECH performance without compromising the selectivity for 5-(HydroxyMethyl) Furfural (HMF) to 2,5-bis(HydroxyMethyl)-Furan (BHMF) formation in comparison to the Ag film. Moreover, a similar ECH current density was recorded at a reduced working potential of 220 mV for rAg. This high performance of rAg is attributed to the formation of new catalytically active sites during the Ag oxidation and reduction processes. This study demonstrates that rAg can potentially be used for the ECH process with minimum energy consumption and a higher production rate.

C3-Alkylation of furfural derivatives by continuous flow homogeneous catalysis

The C3-functionalization of furfural using homogeneous ruthenium catalysts requires the preinstallation of an ortho-directing imine group, as well as high temperatures, which did not allow scaling up, at least under batch conditions. In order to design a safer process, we set out to develop a continuous flow process specifically for the C3-alkylation of furfural (Murai reaction). The transposition of a batch process to a continuous flow process is often costly in terms of time and reagents. Therefore, we chose to proceed in two steps: the reaction conditions were first optimized using a laboratory-built pulsed-flow system to save reagents. The optimized conditions in this pulsed-flow mode were then successfully transferred to a continuous flow reactor. In addition, the versatility of this continuous flow device allowed both steps of the reaction to be carried out, namely the formation of the imine directing group and the C3-functionalization with some vinylsilanes and norbonene.

Conversion of 5-hydroxymethylfurfural to furan-2,5-dicarboxylic acid by a simple and metal-free catalytic system

A simple and metal-free catalytic system composed of NaOtBu/DMF and an O2 balloon efficiently converted 5-hydroxymethylfurfural (5-HMF) to furan-2,5-dicarboxylic acid with an 80.85% yield. 5-HMF analogues and various types of alcohols were also transformed to their corresponding acids in satisfactory to excellent yield by this catalytic system.

Review on supported metal catalysts with partial/porous overlayers for stabilization

Heterogeneous catalysts of supported metals are important for both liquid-phase and gas-phase chemical transformations which underpin the petrochemical sector and manufacture of bulk or fine chemicals and pharmaceuticals. Conventional supported metal catalysts (SMC) suffer from deactivation resulting from sintering, leaching, coking and so on. Besides the choice of active species (e.g. atoms, clusters, nanoparticles) to maximize catalytic performances, strategies to stabilize active species are imperative for rational design of catalysts, particularly for those catalysts that work under heated and corrosive reaction conditions. The complete encapsulation of metal active species within a matrix (e.g. zeolites, MOFs, carbon, etc.) or core-shell arrangements is popular. However, the use of partial/porous overlayers (PO) to preserve metals, which simultaneously ensures the accessibility of active sites through controlling the size/shape of diffusing reactants and products, has not been systematically reviewed. The present review identifies the key design principles for fabricating supported metal catalysts with partial/porous overlayers (SMCPO) and demonstrates their advantages versus conventional supported metals in catalytic reactions.

Enantioselective transformations of 5-hydroxymethylfurfural via catalytic asymmetric 1,3-dipolar cycloaddition of azomethine ylides

A catalytic asymmetric 1,3-dipolar cycloaddition between iminoesters derived from 5-hydroxymethylfurfural (HMF) and different activated alkenes is reported. Excellent levels of diastereo and enantioselectivity were obtained when Fesulphos/Cu^I complex was used as catalyst. This metodology provides an effective and sustainable access to challenging enantioenriched heterocyclic scaffolds and represents one of the rare examples of catalytic asymmetric transformations using HMF as a starting material.

In situ reduction of Cu nanoparticles on Mg-Al-LDH for simultaneous efficient catalytic transfer hydrogenation of furfural to furfuryl alcohol

Herein, we report a simple and highly efficient approach for simultaneous in situ synthesis of Cu nanoparticles on Mg-Al-LDH (in situ reduced CuMgAl-LDH) from Cu-Mg-Al ternary LDH and catalytic transfer hydrogenation of furfural (FAL) to furfuryl alcohol (FOL) using isopropanol (2-PrOH) as a reducing agent and hydrogen source. The in situ reduced CuMgAl-LDH, especially Cu_1.5Mg_1.5Al₁-LDH as a precursor, offered excellent performance for the catalytic transfer hydrogenation of FAL to FOL (achieving almost full conversion with 98.2% selectivity of FOL). Strikingly, the in situ reduced catalyst was robust and stable with a wide scope in the transfer hydrogenation of various biomass-derived carbonyl compounds.

Promoted electrocatalytic hydrogenation of furfural in a bi-phasic system

The promoted electrocatalytic hydrogenation of biomass-derived furfural to 2-methylfuran is for the first time identified in a water/oil bi-phasic system, in which the oil phase can quickly separate hydrophobic products from the electrode/electrolyte interfaces, resulting in a beneficial equilibrium toward hydrodeoxygenation.

Polymers without Petrochemicals: Sustainable Routes to Conventional Monomers

Access to a wide range of plastic materials has been rationalized by the increased demand from growing populations and the development of high-throughput production systems. Plastic materials at low costs with reliable properties have been utilized in many everyday products. Multibillion-dollar companies are established around these plastic materials, and each polymer takes years to optimize, secure intellectual property, comply with the regulatory bodies such as the Registration, Evaluation, Authorisation and Restriction of Chemicals and the Environmental Protection Agency and develop consumer confidence. Therefore, developing a fully sustainable new plastic material with even a slightly different chemical structure is a costly and long process. Hence, the production of the common plastic materials with exactly the same chemical structures that does not require any new registration processes better reflects the reality of how to address the critical future of sustainable plastics. In this review, we have highlighted the very recent examples on the synthesis of common monomers using chemicals from sustainable feedstocks that can be used as a like-for-like substitute to prepare conventional petrochemical-free thermoplastics.

l-Lysine Stabilized FeNi Nanoparticles for the Catalytic Reduction of Biomass-Derived Substrates in Water Using Magnetic Induction

The reduction of biomass-derived compounds gives access to valuable chemicals from renewable sources, circumventing the use of fossil feedstocks. Herein, we describe the use of iron-nickel magnetic nanoparticles for the reduction of biomass model compounds in aqueous media under magnetic induction. Nanoparticles with a hydrophobic ligand (FeNi₃ -PA, PA=palmitic acid) have been employed successfully, and their catalytic performance is intended to improve by ligand exchange with lysine (FeNi₃ -Lys and FeNi₃ @Ni-Lys NPs) to enhance water dispersibility. All three catalysts have been used to hydrogenate 5-hydroxymethylfurfural into 2,5-bis(hydroxymethyl)furan with complete selectivity and almost quantitative yields, using 3 bar of H₂ and a magnetic field of 65 mT in water. These catalysts have been recycled up to 10 times maintaining high conversions. Under the same conditions, levulinic acid has been hydrogenated to γ-valerolactone, and 4'-hydroxyacetophenone hydrodeoxygenated to 4-ethylphenol, with conversions up to 70 % using FeNi₃ -Lys, and selectivities above 85 % in both cases. This promising catalytic system improves biomass reduction sustainability by avoiding noble metals and expensive ligands, increasing energy efficiency via magnetic induction heating, using low H₂ pressure, and proving good reusability while working in an aqueous medium.

Recent Advances in the Efficient Synthesis of Useful Amines from Biomass-Based Furan Compounds and Their Derivatives over Heterogeneous Catalysts

Bio-based furanic oxygenates represent a well-known class of lignocellulosic biomass-derived platform molecules. In the presence of H2 and different nitrogen sources, these versatile building blocks can be transformed into valuable amine compounds via reductive amination or hydrogen-borrowing amination mechanisms, yet they still face many challenges due to the co-existence of many side-reactions, such as direct hydrogenation, polymerization and cyclization. Hence, catalysts with specific structures and functions are required to achieve satisfactory yields of target amines. In recent years, heterogeneous catalytic synthesis of amines from bio-based furanic oxygenates has received extensive attention. In this review, we summarize and discuss the recent significant progress in the generation of useful amines from bio-based furanic oxygenates with H2 and different nitrogen sources over heterogeneous catalysts, according to various raw materials and reaction pathways. The key factors affecting catalytic performances, such as active metals, supports, promoters, reaction solvents and conditions, as well as the possible reaction routes and catalytic reaction mechanisms are studied and discussed in depth. Special attention is paid to the structure–activity relationship, which would be helpful for the development of more efficient and stable heterogeneous catalysts. Moreover, the future research direction and development trend of the efficient synthesis for bio-based amines are prospected.

The Role of Copper in the Hydrogenation of Furfural and Levulinic Acid

Currently, there is a great interest in the development of sustainable and green technologies for production of biofuels and chemicals. In this sense, much attention is being paid to lignocellulosic biomass as feedstock, as alternative to fossil-based resources, inasmuch as its fractions can be transformed into value-added chemicals. Two important platform molecules derived from lignocellulosic sugars are furfural and levulinic acid, which can be transformed into a large spectrum of chemicals, by hydrogenation, oxidation, or condensation, with applications as solvents, agrochemicals, fragrances, pharmaceuticals, among others. However, in many cases, noble metal-based catalysts, scarce and expensive, are used. Therefore, an important effort is performed to search the most abundant, readily available, and cheap transition-metal-based catalysts. Among these, copper-based catalysts have been proposed, and the present review deals with the hydrogenation of furfural and levulinic acid, with Cu-based catalysts, into several relevant chemicals: furfuryl alcohol, 2-methylfuran, and cyclopentanone from FUR, and γ-valerolactone and 2-methyltetrahydrofuran from LA. Special emphasis has been placed on catalytic processes used (gas- and liquid-phase, catalytic transfer hydrogenation), under heterogeneous catalysis. Moreover, the effect of addition of other metal to Cu-based catalysts has been considered, as well as the issue related to catalyst stability in reusing studies.

Reticular Coordination Induced Interfacial Interstitial Carbon Atoms on Ni Nanocatalysts for Highly Selective Hydrogenation of Bio-Based Furfural under Facile Conditions

A rational design of transition metal catalysts to achieve selective hydrogenation of furfural (FFR) to tetrahydrofurfuryl alcohol (THFA) under facile conditions is a promising option. In this work, a series of Ni catalysts were synthesized by controlled thermal treatment of Ni-based metal-organic frameworks (MOFs), with the purpose of modulating the interface of nickel nanoparticles by the reticular coordination in MOF precursors. The catalytic performance indicates that Ni/C catalyst obtained at 400 °C exhibits efficient conversion of FFR (>99%) and high selectivity to THFA (96.1%), under facile conditions (80 °C, 3 MPa H2, 4.0 h). The decomposition of MOF at low temperatures results in highly dispersed Ni0 particles and interfacial charge transfer from metal to interstitial carbon atoms induced by coordination in MOF. The electron-deficient Ni species on the Ni surface results in an electropositive surface of Ni nanoparticles in Ni/C-400, which ameliorates furfural adsorption and enhances the hydrogen heterolysis process, finally achieving facile hydrogenation of FFR to THFA.

Role of lattice strain in bifunctional catalysts for tandem furfural hydrogenation–esterification

This research represents that the bifunctional catalyst (Cu/RHSiO2–Al–Mg) which has the lowest lattice strain can significantly enhance catalytic reactivity such as the furfural conversion into furfural acetate.

Preparation of Environmentally Friendly Glueless Boxwood Timber by Acidic Environmental Treatment and High-Temperature Pressing

In the context of high-quality development, environmental issues are being paid more and more attention to, and the release of free formaldehyde has become a major problem that needs to be solved. Glueless plywood mainly adopts natural substances as raw materials, without adding chemical products, such as resin adhesives, and it does not contain harmful substances, such as formaldehyde. Glueless plywood is a green product that causes no pollution in the environment and no harm to the human body. In this study, the corresponding weak-phase components in boxwood were pre-delivered by an acidic environmental treatment, and the high-temperature and high-pressure compacting process produced a glueless boxwood panel with excellent water resistance and mechanical properties, while remaining environmentally friendly.

Synthesis of Co-Ni Alloy Particles with the Structure of a Solid Substitution Solution by Precipitation in a Supercritical Carbon Dioxide

Mixed Co-Ni bimetallic systems with the structure of a solid substitution solution have been synthesized using the supercritical antisolvent precipitation (SAS) method, which uses supercritical CO₂ as an antisolvent. The systems obtained have been characterized in detail using X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), Fourier-transform infrared (FTIR) spectroscopy, and magnetostatic measurements. It has been found that Co-enriched systems have a defective hexagonal close-packed (hcp) structure, which was described by a model which embedded cubic fragments of packaging into a hexagonal close-packed (hcp) structure. It has been shown that an increase in water content at the precipitation stage leads to a decrease in the size of cubic fragments and a more uniform distribution of them in Co-enriched systems. It has also been shown that mixed systems have the greatest coercivity in the line of samples. Ni-enriched bimetallic systems have a cubic close-packed (ccp) structure with modified crystal lattice parameters.

Spillover Hydrogen on Electron-Rich Ni/m-TiO2 for Hydrogenation of Furfural to Tetrahydrofurfuryl Alcohol

Conversion of biomass-derived furfural (FFA) platform molecule to value-added tetrahydrofurfuryl alcohol (THFA) molecule is a sustainable route using an efficient non-noble metallic catalyst in water solvent. In this work, Ni in various loadings on mesoporous titanium dioxide (m-TiO2) was synthesized in one pot by Evaporation-Induced Self-Assembly (EISA). The synthesised catalysts were evaluated for the hydrogenation of furfural to tetrahydrofurfuryl alcohol. The catalysts were characterised using a combination of spectroscopic techniques such as XRD, H2-TPR, H2-TPD, XPS, SEM-EDX, TEM, and HR-TEM. The characterization results show that the Ni/m-TiO2 materials exhibit enhanced electron-rich active sites, facilitated hydrogen spillover, uniform dispersion of small Ni particles (~5 nm), and strong metal support interaction between Ni and TiO2. Among the various Ni dopings, 7.5 wt.% Ni/m-TiO2 catalyst exhibited the best performance and achieved 99.9% FFA conversion and 93.2% THFA selectivity in water solvent at 100 °C and under 2 MPa H2. Additionally, detailed kinetic studies, process parameters, the stability and reusability of the catalyst were also studied. The results demonstrated that the 7.5 wt.% Ni/m-TiO2 catalyst is highly active and stable.