Spatial-Temporal Dispersion of Aerosolized Nanoparticles During the Use of Consumer Spray Products and Estimates of Inhalation Exposure

Research on factors affecting the spread of dust pollution in conveyor belt workshop and research on wet dust reduction technology

At this stage, there are many dust-hazardous industries, and occupational pneumoconiosis has a high incidence for a long time. To solve the dust pollution problem in coal processing plant workshops, the dust particle field and liquid droplet particle field were numerically simulated using computational fluid dynamics (CFD), and the influences of the induced airflow and corridor wind speed on the internal airflow field of the workshop were investigated to derive the dust pollution mechanism in the coal plant workshop under the change in the wind flow field. In this study, it was shown that the wind flow rate in the coal processing plant workshop is mainly affected by the corridor wind speed, and the higher the corridor wind speed is, the higher the wind flow rate. The induced airflow mainly affected the direction of the wind flow field in the workshop. According to the conclusions obtained from the simulations, a spray dust reduction system was designed for the coal processing plant workshop and applied in the Huangyuchuan coal processing plant. On-site measurement revealed that the dust reduction effect inside the coal processing plant workshop is obvious, and the overall dust reduction efficiency in the workshop reaches more than 94%, which meets the requirements of environmentally sustainable development and clean production.

Numerical simulation of the fine kinetics of dust reduction using high-speed aerosols

A numerical model of single-particle fog-dust collision coupling in a high-speed airflow based on three-phase flow theory. The effect of the fog-to-dust particle size ratio, relative velocity between the fog and dust particles, collision angle and contact angle at the wetting humidity function of dust particles is investigated. Different particle size ratios are determined for achieving the optimal wetting humidity for the interaction of high-velocity aerosols with dust particles of different sizes, for differ, that is, kPM2.5 = 2:1, kPM10 = 3.5:1 and kPM20 = 1.5:1. The optimal humidity increases with the relative velocity U between the fog and dust particles in the high-speed airflow. The larger the collision angle is, the lower the wetting rate is.The smaller the contact angle between the solid and liquid is, the better droplet wetting on dust is. The fine kinetic mechanism of single-particle fog-dust collision-coupling in a high-speed airflow is elucidated in this study.

Characterization of the aerosol release from spray cleaning and disinfection products - Spray scenarios in a climate chamber

Cleaning work using spray products has been associated with adverse respiratory effects but little is known of the exposure concentrations. The purpose of this study was to characterize aerosol generation at spray scenarios in a controlled climate chamber. Spraying on vertically and horizontally oriented surfaces, as well as spraying on a cloth, was investigated. Furthermore, the effect of nozzle geometry was tested. The average mass generation rates of six pressurized spray cans and 13 trigger sprays were about 1.7 g/s and did not differ significantly, but the average values of the individual sprays had large variations (0.5-3.1 g/s). The time required to halve the air concentration of aerosol particles, the half-life time, was determined for all spray products. The average half-life time of the total particle mass concentration (TPMC) of the pressurized spray cans was 0.5 h versus 0.25 h for trigger sprays. Gravimetrically determined airborne fractions of pressurized spray cans tended to be higher than those of trigger sprays. However, airborne fractions based on the measured peak TPMC were up to three orders of magnitude smaller. A comparison of different trigger spray nozzles when spraying the same product showed that the TPMC can be up to 18 times higher for the largest emitting nozzle. The distance of the nozzle to a cloth should be 1 cm to significantly reduce the concentration of the generated aerosols. ConsExpo modeling predicted the measured peak TPMC well but less well the decay.

Nanoparticle Effects on Stress Response Pathways and Nanoparticle-Protein Interactions

Nanoparticles (NPs) are increasingly used in a wide variety of applications and products; however, NPs may affect stress response pathways and interact with proteins in biological systems. This review article will provide an overview of the beneficial and detrimental effects of NPs on stress response pathways with a focus on NP-protein interactions. Depending upon the particular NP, experimental model system, and dose and exposure conditions, the introduction of NPs may have either positive or negative effects. Cellular processes such as the development of oxidative stress, the initiation of the inflammatory response, mitochondrial function, detoxification, and alterations to signaling pathways are all affected by the introduction of NPs. In terms of tissue-specific effects, the local microenvironment can have a profound effect on whether an NP is beneficial or harmful to cells. Interactions of NPs with metal-binding proteins (zinc, copper, iron and calcium) affect both their structure and function. This review will provide insights into the current knowledge of protein-based nanotoxicology and closely examines the targets of specific NPs.

Potential consumer exposure to respirable particles and TiO2 due to the use of eyebrow powders

BACKGROUND

Cosmetic powders contain numerous components, including titanium dioxide (TiO₂), which is classified as possibly carcinogenic to humans (Group 2B). However, little is known about potential inhalation exposures to particles that are released during cosmetic powder applications.

METHODS

We realistically simulated the application of five different eyebrow powders using a mannequin and then determined concentrations of total suspended particles (TSP), PM₁₀, and PM₄ fractions of particles that would be inhaled during powder application. We determined the size and shape of particles in the original powders and released particles, as well as their TiO₂ concentrations and Ti content of individual particles.

RESULTS

The application of eyebrow powders resulted in the release and inhalation of airborne particles at concentrations ranging from 21.2 to 277.3 µg/m³, depending on the particle fraction and the powder. The concentrations of TiO₂ in PM₄ and PM₁₀ samples reached 2.7 µg/m³ and 9.3 µg/m³, respectively. The concentration of TiO₂ in airborne particle fractions was proportional to the presence of TiO₂ in the bulk powder.

CONCLUSION

The application of eyebrow powders results in user exposures to respirable PM₄ and PM₁₀ particles, including those containing TiO₂. This information should be of interest to stakeholders concerned about inhalation exposure to TiO₂.

Spatial Uncertainty in Modeling Inhalation Exposure to Volatile Organic Compounds in Response to the Application of Consumer Spray Products

(1) Background: Mathematical exposure modeling of volatile organic compounds (VOCs) in consumer spray products mostly assumes instantaneous mixing in a room. This well-mixed assumption may result in the uncertainty of exposure estimation in terms of spatial resolution. As the inhalation exposure to chemicals from consumer spray products may depend on the spatial heterogeneity, the degree of uncertainty of a well-mixed assumption should be evaluated under specific exposure scenarios. (2) Methods: A room for simulation was divided into eight compartments to simulate inhalation exposure to an ethanol trigger and a propellant product. Real-time measurements of the atmospheric concentration in a room-sized chamber by proton transfer reaction mass spectrometry were compared with mathematical modeling to evaluate the non-homogeneous distribution of chemicals after their application. (3) Results: The well-mixed model overestimated short-term exposure, particularly under the trigger spray scenario. The uncertainty regarding the different chemical proportions in the trigger did not significantly vary in this study. (4) Conclusions: Inhalation exposure to aerosol generating sprays should consider the spatial uncertainty in terms of the estimation of short-term exposure.

Exploitation of Antimicrobial Nanoparticles and Their Applications in Biomedical Engineering

Antibiotic resistance is a major threat to public health, which contributes largely to increased mortality rates and costs in hospitals. The severity and widespread nature of antibiotic resistance result in limited treatments to effectively combat antibiotic-resistant pathogens. Nanoparticles have different or enhanced properties in contrast to their bulk material, including antimicrobial efficacy towards a broad range of microorganisms. Their beneficial properties can be utilised in various bioengineering technologies. Thus, antimicrobial nanoparticles may provide an alternative to challenge antibiotic resistance. Currently, nanoparticles have been incorporated into materials, such as fibres, glass and paints. However, more research is required to elucidate the mechanisms of action fully and to advance biomedical applications further. This paper reviews the antimicrobial efficacies and the intrinsic properties of different metallic nanoparticles, their potential mechanisms of action against certain types of harmful pathogens and how these properties may be utilised in biomedical and healthcare products with the aim to reduce cross contaminations, disease transmissions and usage of antibiotics.

Developmental exposure to silver nanoparticles leads to long term gut dysbiosis and neurobehavioral alterations

Due to their antimicrobial properties, silver nanoparticles (AgNPs) are used in a wide range of consumer products that includes topical wound dressings, coatings for biomedical devices, and food-packaging to extend the shelf-life. Despite their beneficial antimicrobial effects, developmental exposure to such AgNPs may lead to gut dysbiosis and long-term health consequences in exposed offspring. AgNPs can cross the placenta and blood–brain-barrier to translocate in the brain of offspring. The underlying hypothesis tested in the current study was that developmental exposure of male and female mice to AgNPs disrupts the microbiome–gut–brain axis. To examine for such effects, C57BL6 female mice were exposed orally to AgNPs at a dose of 3 mg/kg BW or vehicle control 2 weeks prior to breeding and throughout gestation. Male and female offspring were tested in various mazes that measure different behavioral domains, and the gut microbial profiles were surveyed from 30 through 120 days of age. Our study results suggest that developmental exposure results in increased likelihood of engaging in repetitive behaviors and reductions in resident microglial cells. Echo-MRI results indicate increased body fat in offspring exposed to AgNPs exhibit. Coprobacillus spp., Mucispirillum spp., and Bifidobacterium spp. were reduced, while Prevotella spp., Bacillus spp., Planococcaceae, Staphylococcus spp., Enterococcus spp., and Ruminococcus spp. were increased in those developmentally exposed to NPs. These bacterial changes were linked to behavioral and metabolic alterations. In conclusion, developmental exposure of AgNPs results in long term gut dysbiosis, body fat increase and neurobehavioral alterations in offspring.

Estimates of particulate matter inhalation doses during three-dimensional printing: How many particles can penetrate into our body?

Harmful emissions including particulates, volatile organic compounds, and aldehydes are generated during three-dimensional (3D) printing. Ultrafine particles are particularly important due to their ability to penetrate deep into the lung. We modeled inhalation exposure by particle size during 3D printing. A total of six thermoplastic filaments were used for printing under manufacturer's recommended conditions, and particle emissions in the size range between 10 nm and 10 μm were measured. The inhalation exposure dose including inhaled and deposited doses was estimated using a mathematical model. For all materials, the number of particles between 10 nm and 1 μm accounted for a large proportion among the released particles, with nano-sized particles being the dominant size. More than 1.3 × 10⁹ nano-sized particles/kgbw/g (95.3 ± 104.0 ng/kgbw/g) could be inhaled, and a considerable amount was deposited in respiratory regions. The total deposited dose in terms of particle number was 3.1 × 10⁸ particles/kgbw/g (63.6% of the total inhaled dose), and most (41.3%) were deposited in the alveolar region. The total mass of particles deposited was 19.8 ± 16.6 ng/kgbw/g, with 10.1% of the total mass deposited in the alveolar region. Given our findings, the inhalation exposure level is mainly determined by printing conditions, particularly the filament type and manufacturer-recommended extruder temperature.

Estimates of lung burden risk associated with long-term exposure to TiO2 nanoparticles as a UV-filter in sprays

Titanium dioxide (TiO2) nanoparticles (NPs) are employed as an ultraviolet filter in sunscreen products because of their high ultraviolet absorptivity. However, sunscreen sprays may pose health risks due to the toxicity of inhaled TiO2 NPs. Therefore, we estimated the potential human health risk posed by inhaled TiO2 NPs emitted from sunscreen sprays. The physiology-based lung model was employed to predict the lung TiO2 NPs burden caused by long-term exposure. A Hill-based dose-response model described the relationship between lung inflammation and TiO2 NP accumulation. The Weibull threshold model was used to estimate the threshold amount of accumulation inducing 0.5% of the maximum increase in neutrophils. The potential health risk was assessed using a hazard quotient-based probabilistic risk model. All data obtained to date indicate that application of sunscreen sprays poses no significant health risk. However, using data simulations based on the threshold criterion, we discovered that in terms of practical strategies for preventing the risks posed by inhaled TiO2 NPs emitted from spray products, the suggested daily use amount and pressing number are 40 g (95% confidence interval: 11-146 g) and 66 (18-245), respectively. In this study, we successfully translated the potential health risk of long-term exposure to NP-containing sunscreen sprays and recommendations for daily application into mechanistic insights.

Antimicrobial Properties of the Ag, Cu Nanoparticle System

Microbes, including bacteria and fungi, easily form stable biofilms on many surfaces. Such biofilms have high resistance to antibiotics, and cause nosocomial and postoperative infections. The antimicrobial and antiviral behaviors of Ag and Cu nanoparticles (NPs) are well known, and possible mechanisms for their actions, such as released ions, reactive oxygen species (ROS), contact killing, the immunostimulatory effect, and others have been proposed. Ag and Cu NPs, and their derivative NPs, have different antimicrobial capacities and cytotoxicities. Factors, such as size, shape and surface treatment, influence their antimicrobial activities. The biomedical application of antimicrobial Ag and Cu NPs involves coating onto substrates, including textiles, polymers, ceramics, and metals. Because Ag and Cu are immiscible, synthetic AgCu nanoalloys have different microstructures, which impact their antimicrobial effects. When mixed, the combination of Ag and Cu NPs act synergistically, offering substantially enhanced antimicrobial behavior. However, when alloyed in Ag-Cu NPs, the antimicrobial behavior is even more enhanced. The reason for this enhancement is unclear. Here, we discuss these results and the possible behavior mechanisms that underlie them.

Characterisation of particles within and aerosols produced by nano-containing consumer spray products

Nanoparticles have been incorporated into a range of consumer spray products, providing the potential for inadvertent inhalation by users and bystanders. The levels and characteristics of nanoparticle inhalation exposures arising from the use of such products are important inputs to risk assessments and informing dose regimes for in vitro and in vivo studies investigating hazard potentials. To date, only a small number of studies have been undertaken to explore both the aerosols generated from such products and the metal nanoparticles within them. The objective of the current study was to add to the limited data in this field by investigating a range of nano-containing spray products available within the UK. Six products were selected and the nanoparticles characterised using a combination of techniques, including: inductively coupled plasma mass spectrometry (ICP-MS), dynamic light scattering (DLS), nanoparticle tracking analysis (NTA), transmission electron microscopy energy-dispersive X-ray spectroscopy (TEM-EDX) and single particle ICP-MS (spICP-MS). The aerosol produced by these products, when sprayed within a glovebox, was characterised by scanning mobility particle sizer (SMPS) and an aerodynamic particle sizer (APS). A cascade impactor with thirteen stages (NanoMOUDI) was used with one product to generate information on the size specific nanoparticle elemental distribution within the aerosol. The results demonstrated the presence of solid nanoparticles (silver, gold or silica) in each of the products at low concentrations (<13 ppm). TEM and (sp)ICP-MS provided reliable information on nanoparticle size, shape, number and mass, while the light scattering methods were less effective due to the complex matrices of the products and their lack of chemical specificity. The aerosols varied significantly across products, with particle and mass concentrations spanning 5 orders of magnitude (10 - 106 cm-3 and 0.3-7600 μg m-3, respectively). The NanoMOUDI results clearly indicated non-uniform distribution of silver within different aerosol particle size ranges.

A Review of Low-Cost Particulate Matter Sensors from the Developers' Perspectives

The concerns related to particulate matter's health effects alongside the increasing demands from citizens for more participatory, timely, and diffused air quality monitoring actions have resulted in increasing scientific and industrial interest in low-cost particulate matter sensors (LCPMS). In the present paper, we discuss 50 LCPMS models, a number that is particularly meaningful when compared to the much smaller number of models described in other recent reviews on the same topic. After illustrating the basic definitions related to particulate matter (PM) and its measurements according to international regulations, the device's operating principle is presented, focusing on a discussion of the several characterization methodologies proposed by various research groups, both in the lab and in the field, along with their possible limitations. We present an extensive review of the LCPMS currently available on the market, their electronic characteristics, and their applications in published literature and from specific tests. Most of the reviewed LCPMS can accurately monitor PM changes in the environment and exhibit good performances with accuracy that, in some conditions, can reach R2 values up to 0.99. However, such results strongly depend on whether the device is calibrated or not (using a reference method) in the operative environment; if not, R2 values lower than 0.5 are observed.

Modeling consumer exposure to spray products: an evaluation of the ConsExpo Web and ConsExpo nano models with experimental data

To ensure safe use of chemical substances in consumer products, the exposure of consumers to these substances needs to be evaluated. For this purpose, generally consumer exposure modeling tools are used. To build confidence in such tools, evaluation of their performance with experimental data is indispensable. This work describes the evaluation of two consumer exposure modeling tools: ConsExpo Web and ConsExpo nano. Both models contain a module to estimate exposure of substances released as an aerosol during the use of spray products. This particular model was tested by comparing measured exposure data with model simulations. Experimental data were obtained from the public literature. These typically provide measured air concentrations under simulated use conditions of spray products. ConsExpo Web and ConsExpo nano were used to simulate experimental settings of the different studies. The resulting simulated air concentrations were compared with the reported ones. Overall, good agreement between modeled and measured data was observed. However, a significant proportion of the studies considered, did not provide sufficient detail in the specification of the experimental conditions to make them suitable for model evaluation. Critical information that was often lacking was on product composition, the mass sprayed during usage, and the generated aerosol size distribution.

Chemicals inhaled from spray cleaning and disinfection products and their respiratory effects. A comprehensive review

Spray cleaning and disinfection products have been associated with adverse respiratory effects in professional cleaners and among residents doing domestic cleaning. This review combines information about use of spray products from epidemiological and clinical studies, in vivo and in vitro toxicological studies of cleaning chemicals, as well as human and field exposure studies. The most frequent chemicals in spray cleaning and disinfection products were compiled, based on registrations in the Danish Product Registry. The chemicals were divided into acids, bases, disinfectants, fragrances, organic solvents, propellants, and tensides. In addition, an assessment of selected cleaning and disinfectant chemicals in spray products was carried out. Chemicals of concern regarding respiratory effects (e.g. asthma) are corrosive chemicals such as strong acids and bases (including ammonia and hypochlorite) and quaternary ammonium compounds (QACs). However, the evidence for respiratory effects after inhalation of QACs is ambiguous. Common fragrances are generally not considered to be of concern following inhalation. Solvents including glycols and glycol ethers as well as propellants are generally weak airway irritants and not expected to induce sensitization in the airways. Mixing of certain cleaning products can produce corrosive airborne chemicals. We discuss different hypotheses for the mechanisms behind the development of respiratory effects of inhalation of chemicals in cleaning agents. An integrative assessment is needed to understand how these chemicals can cause the various respiratory effects.

In vitro intestinal toxicity of commercially available spray disinfectant products advertised to contain colloidal silver

The use of colloidal silver-containing products as dietary supplements, immune boosters and surface disinfectants has increased in recent years which has elevated the potential for human exposure to silver nanoparticles and ions. Product mislabeling and long-term use of these products may put consumers at risk for adverse health outcomes including argyria. This study assessed several physical and chemical characteristics of five commercial products as well as their cytotoxicity using a rat intestinal epithelial cell (IEC-6) model. Concentrations of silver were determined for both the soluble and particulate fractions of the products. Primary particle size distribution and elemental composition were determined by transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), respectively. Hydrodynamic diameters were measured using nanoparticle tracking analysis (NTA) and dynamic light scattering (DLS). The effect of gastrointestinal (GI) simulation on the colloidal silver products was determined using two systems. First, physical and chemical changes of the silver nanoparticles in these products was assessed after exposure to Synthetic Stomach Fluid (SSF) resulting in particle agglomeration, and the appearance of AgCl on the surfaces and between particles. IEC-6 cells were exposed for 24 h to dilutions of the products and assessed for cell viability. The products were also treated with a three-stage simulated GI system (stomach and intestinal fluids) prior to exposure of the IEC-6 cells to the isolated silver nanoparticles. Cell viability was affected by each of the consumer products. Based on the silver nitrate and commercial silver nanoparticle dose response, the cytotoxicity for each of the colloidal silver products was attributed to the particulate silver, soluble silver or non‑silver matrix constituents.

Behavioral characteristics to airborne particles generated from commercial spray products

Commercial spray products are commonly used in daily life and airborne particles generated by these products may cause adverse health effects. Our study was aimed to characterize the behaviors of airborne particles from spray products and to determine the deposition loss rate. Four categories of spray products with highly frequent use - air fresheners, fabric deodorants, window cleaners, and a bathroom cleaner - were selected for the study. The products were applied in a cleanroom according to the instructions for use. Airborne particles (10-10,000 nm) were measured within the breathing zone of a user with a scanning mobility particle sizer and an optical particle spectrometer. Additionally, filter sampling was performed to examine the morphological characteristics of the particles using a field emission-scanning electron microscope (FE-SEM). The initial concentration and particle size distribution varied among different spray types and products. Two propellant-type air fresheners that we tested showed a high initial concentration of smaller sized particles. However, one of these and all hand-pressure type propellants showed a low initial concentration in all size ranges. We observed that particles in nucleation mode (10-31.6 nm) decreased and aggregated particles shifted to accumulation mode (100-1,000 nm) over time. The FS-SEM analysis confirmed the aggregation of nano-sized particles for all products. The deposition loss rates of various particle sizes depended on the initial concentration and distribution of particle sizes. For two air fresheners with high initial concentrations, the loss rate of small-sized particles was higher than that of the other products whereas the particle loss rate of large-sized particles was higher, regardless of initial concentration. The results of this study can give us useful information in the behaviors of airborne particles in the consumer spray products and resulting exposure assessment especially in the application to the exposure modeling of spray products.

Transformation pathways and fate of engineered nanoparticles (ENPs) in distinct interactive environmental compartments: A review

The ever increasing production and use of nano-enabled commercial products release the massive amount of engineered nanoparticles (ENPs) in the environment. An increasing number of recent studies have shown the toxic effects of ENPs on different organisms, raising concerns over the nano-pollutants behavior and fate in the various environmental compartments. After the release of ENPs in the environment, ENPs interact with various components of the environment and undergoes dynamic transformation processes. This review focus on ENPs transformations in the various environmental compartments. The transformation processes of ENPs are interrelated to multiple environmental aspects. Physical, chemical and biological processes such as the homo- or hetero-agglomeration, dissolution/sedimentation, adsorption, oxidation, reduction, sulfidation, photochemically and biologically mediated reactions mainly occur in the environment consequently changes the mobility and bioavailability of ENPs. Physico-chemical characteristics of ENPs (particle size, surface area, zeta potential/surface charge, colloidal stability, and core-shell composition) and environmental conditions (pH, ionic strength, organic and inorganic colloids, temperature, etc.) are the most important parameters which regulated the ENPs environmental transformations. Meanwhile, in the environment, organisms encountered multiple transformed ENPs rather than the pristine nanomaterials due to their interactions with various environmental materials and other pollutants. Thus it is the utmost importance to study the behavior of transformed ENPs to understand their environmental fate, bioavailability, and mode of toxicity.

Behavioral characteristics of polyhexamethyleneguanidine (PHMG) particles in aqueous solution and air when sprayed into an ultrasonic humidifier

Polyhexamethyleneguanidine (PHMG) is widely used as a disinfectant to prevent microbial contamination in ultrasonic humidifiers in Korea; however, sales have been prohibited by the government after an outbreak of severe lung injury among humidifier disinfectant users. This study was therefore conducted to determine the characteristics of PHMG particles in aqueous solution and to investigate the behavior of airborne particles generated when using PHMG as a humidifier disinfectant. Three types of PHMG were selected (manufactured in Korea, USA, and China), with dynamic light scattering (DLS) used to determine their behavioral characteristics in aqueous solution. To determine the airborne behavioral characteristics, PHMG was diluted to obtain high (62.5-65 ppm) and low (6.25-6.5 ppm) concentrations, and then real-time monitoring instruments were used to measure the effect of using a diffusion dryer and thermodenuder to control moisture in a cleanroom. A polycarbonate filter sample was analyzed by field emission-scanning electron microscope-energy dispersive spectrometry (FE-SEM-EDS) to determine the particle morphology. The DLS intensity results for the three products showed a slightly right-shifted (~100 nm) bimodal distribution relative to the airborne particle size distribution. The size of the airborne PHMG particles increased during the spraying due to aggregation, with the particle size of aggregated particles confirmed by FE-SEM to be approximately 20 nm or more. As the PHMG concentration increased by 10 times, the airborne concentrations measured by the real-time monitoring instrument increased by 2-3 times for nanoparticles, and by 45-85 times for 1-10 μm particles during humidifier operation; however, 99% of the particles generated could be classified as PM₁. Without ventilation, even after operating the humidifier, the PHMG particles could be airborne for about 2 h until the background concentration was reached. Therefore, we found that the airborne behavior was affected by PHMG concentration. Products from different manufacturers had no effect on the airborne behavior.

Transformation and release of nanoparticle additives & byproducts from commercially available surface coatings on pressure treated lumber via dermal contact

Production and marketing of "nano-enabled" products for consumer purchase has continued to expand. However, many questions remain about the potential release and transformation of these nanoparticle (NP) additives from products throughout their lifecycle. In this work, two surface coating products advertised as containing ZnO NPs as active ingredients, were applied to micronized copper azol (MCA) and aqueous copper azol (ACA) pressure treated lumber. Coated lumber was weathered outdoors for a period of six months and the surface was sampled using a method developed by the Consumer Product Safety Commission (CPSC) to track potential human exposure to ZnO NPs and byproducts through simulated dermal contact. Using this method, the total amount of zinc extracted during a single sampling event was <1 mg/m² and no evidence of free ZnO NPs was found. Approximately 0.5% of applied zinc was removed via simulated dermal contact over 6-months, with increased weathering periods resulting in increased zinc release. XAFS analysis found that only 27% of the zinc in the as received coating could be described as crystalline ZnO and highlights the transformation of these mineral phases to organically bound zinc complexes during the six-month weathering period. Additionally, SEM images collected after sampling found no evidence of free NP ZnO release during simulated dermal contact. Both simulated dermal contact experiments, and separate leaching studies demonstrate the application of surface coating solutions to either MCA and ACA lumber will reduce the release of copper from the pressure treated lumber. This work provides clear evidence of the transformation of NP additives in consumer products during their use stage.

Characterization of an aerosol generation system to assess inhalation risks of aerosolized nano-enabled consumer products

Objective: The aerosolization of common nano-enabled consumer products such as cosmetics has significantly increased engineered nanoparticle inhalation risks. While several studies have investigated the impact of cosmetic dermal exposures, inhalation hazards of aerosolized cosmetics are much less known but could pose considerable harm to users due to potential co-exposure of nanoparticles and other product components.Materials and Methods: In this study, we developed a fully automated aerosol generation system to examine the aerosol properties of four aerosolized nano-enabled cosmetics using real-time monitoring and sampling instrumentation. Physicochemical characterization of aerosols was conducted using scanning electron microscopy coupled with energy dispersive x-ray spectroscopy (SEM-EDX). Characterization and calibration of animal exposure pods coupled to the system were also performed by measuring and comparing particle concentrations between pods.Results and Discussion: Results show peak emissions are shade dependent and varied between 12,000-22,000 particles/cm³ with modal diameters ranging from 36 nm-1.3 µm. SEM-EDX analysis determined that the original products and collected aerosols have similar morphological features consisting of micron-sized particles decorated with nanoparticles and crystalline structures. Mean total particle concentration in pods at 5 and 10 mg/m³ target levels were 2.22E + 05 #/cm³ and 4.33E + 05 #/cm³, respectively, with <10% variability between pods.Conclusions: The fully automated exposure platform described herein provides reproducible aerosol generation, conforms to recommended guidelines on chemical testing, and therefore is suitable for future in vivo toxicological assessments to examine potential respiratory hazards of aerosolized nano-enabled consumer products.

Characteristics of exposure factors and inhalation exposure to selected spray consumer products in Korean population

Many consumer spray products are sold for various purposes. Use of spray products can cause adverse health effects. This study evaluated exposure factors for consumer spray products and assessed the particle inhalation exposure. Six consumer spray products were evaluated: an automobile interior cleaner, car deodorizing spray, anti-static spray, waterproofing spray, microorganism deodorizer, and disinfectant spray. The exposure factors were based on 10,000 respondents over 15 years old. Inhalation dose was calculated from the concentration released into the room air and time used. The use rates of the spray products ranged from 0.4 to 11% and differed significantly by gender (p < 0.001). Aerosol types had a higher mass per use and longer duration of usage than trigger types. The median concentration of the trigger type ranged from 17.35 to 373.38 mg/m³, while that of the aerosol type ranged from 36.66 to 1601.97 mg/m³. The median inhalation dose of the trigger and aerosol types ranged from 2.04 × 10^-3 to 0.20 and 2.60 × 10^-3 to 1.71 mg/kg/day, respectively. The inhalation dose of the disinfectant spray increased with the level of education (p < 0.001), while the inhalation doses of the other spray products were not significantly associated with gender, age, income, or education.

Assessing human exposure risk and lung disease burden posed by airborne silver nanoparticles emitted by consumer spray products

Background

No systematic investigations have been conducted to assess the lung burden imposed by the chronic inhalation of silver nanoparticles (AgNPs) emitted by spray products.

Objective

The objective of this study was to formulate a study framework that integrates a probabilistic risk assessment scheme with a mechanistic lung burden model for the estimation of health risks associated with the long-term inhalation of AgNP-containing spray products.

Materials and methods

A compartmentalized physiologically based alveolar deposition (PBAD) model was used to estimate AgNP lung burden. Dose–response relationships were established using nanotoxicity data sets obtained from rats (as a model organism). Weibull model-based thresholds of AgNP lung burden based on neutrophil-elevated inflammation bio-markers were estimated from Hill-based exposure–response relationships. Finally, the risks of lung disease posed by various AgNP-containing spray products were assessed.

Results

Conservative thresholds for the prevention of pulmonary disease were estimated as follows (mean ± SE): 34 nm AgNPs (0.32±0.22 mg) and 60 nm AgNPs (1.08±0.64 mg). Our results indicate that the risk probability was ~0.5 that the hazard quotient (HQ) estimates of deodorant with a count median diameter (CMD) ≈30 nm exceeded 1. The primary risk posed by AgNPs is transferred from the interstitial region to lymph nodes. Under the condition of 50% risk probability, the 97.5 percentile of HQ for the spray products were as follows: CMD ≈30 nm (~3.4) and CMD ≈60 nm (~1.1).

Conclusion

Our application of the proposed risk assessment scheme to the results obtained in an in vivo animal model proved highly effective in elucidating the relationship between the characteristics of metallic NP-containing spray products and their corresponding toxicity. The integration of the proposed PBAD model with a risk assessment framework enables the rapid assessment of risk posed by spray products containing metallic NPs over various time scales.

How critical is geometrical confinement? Analysis of spatially and temporally resolved particulate matter removal with an electrostatic precipitator

This study investigates the spatial and temporal dispersion of particulate matter (PM) when using a needle-type electrostatic precipitator (ESP). The ESP is installed in tubes of 3 and 10 cm diameter. A simple light scattering setup integrated with image processing is built to evaluate and quantify the spatial and temporal dispersion of PM. The ESP is operated under stationary and continuous flowing modes to test its PM removal capability. Under the stationary mode, PM is removed efficiently in 10 and 45 seconds when using a 3 and 10 cm tube, respectively. In a more geometrically confined system, a large spatial particulate concentration gradient is seen from 18 to 24 cm, indicating that the cleaning capability can be controlled within a localized space. By modulating the applied voltage from direct current (DC) to a low-frequency pulse with 50% duty, the ozone concentration can be reduced by nearly 50% while maintaining the cleaning efficiency. The analysis with spatially and temporally resolved particulate dispersion provides a novel strategy for testing the performance of an ESP. Furthermore, physical confinement enhances both the spatial and temporal removal efficiency, which is crucial for indoor and personal air cleaning devices. These results will contribute to air purification and environmental monitoring.