Capacitive Deionization of Saline Water by Using MoS2-Graphene Hybrid Electrodes with High Volumetric Adsorption Capacity

N, O-codoped carbon aerogel electrode improves capacitive deionization performance

Capacitive deionization (CDI) using porous carbon materials provides an environmentally friendly and sustainable solution to produce affordable fresh water. However, low salt adsorption rates significantly limit its practical application. In this study, N, O-codoped carbon aerogel (NOCA) was prepared by a simple sol-gel method using agar as the carbon framework, NaCl as the template, NH4HCO3 as the nitrogen source and self-blowing agent. The electrochemical and electrosorption properties of the NOCA electrode were significantly better than compared to commercial activated carbon (CAC) electrodes. The NOCA material had the following characteristics: (i) During the rapid freeze-drying process, NaCl crystals provide a three-dimensional network structure for effective dispersion of agar, reducing the agglomeration of particles. The volatile gas generated during the thermal decomposition of NH4HCO3 reduces the plugging of pores. (ii) The fluffy interconnecting network structure of the material enhances its electrical conductivity, providing sufficient channels and adsorption sites for the entry and exit of salt ions. (iii) The abundant hydroxyl and ether groups in the agar enhance the hydrophilicity of the material, whereas N doping further improves the electrical conductivity and reduces the ion transport resistance. The electrosorption capacity and adsorption rate of the NOCA material in 500 mg/L NaCl solution were 22.1 mg/g and 4.4 mg/(g·min), respectively. These values correspond to low energy consumption and high energy recovery efficiency in the electrosorption process. The adsorption capacity remained at 95.5 % after 50 adsorption/desorption cycles. These findings show that NOCA is a novel and potential electrode material for CDI applications.

Microbial Surface Confined Growth Strategy for the Synthesis of Highly Loaded NiCoP Nanoparticles with Hollow Derived Carbon Shells for Sodium Ion Capture

NiCoP is considered to be a very promising material for sodium ion (Na+) capturing, however, the volume expansion and poor cyclic stability of NiCoP during the storage limit its application. In response to these limitations, Finite element simulations are used to help in the rational design of the NiCoP structure. A novel microbial surface confined growth strategy is employed to synthesize highly loaded NiCoP nanoparticles (NiCoP NPs) supported on hollow derived carbon shells (NPC), constructing a stable composite structure known as NiCoP@NPC. The highly loaded and uniformly dispersed NiCoP NPs are anchored in-situ and fully exposed, enabling enhanced electron and ion transport efficiency and thereby boosting pseudocapacitance. The NPC from yeast played a crucial role in mitigating the volume expansion of NiCoP NPs, thereby enhancing the structural stability of the electrode. Consequently, NiCoP@NPC demonstrated a high Na+ storage capacity of 59.70 ± 1.51 mg g-1 at 1.6 V and maintained good cycling stability, retaining over 73.3% of its capacity after 80 cycles at 1.6 V. Scanning transmission X-ray microscopy (STXM) analysis confirmed the reversible conversion reaction mechanism and the robust structure of NiCoP@NPC before and after the reaction; Density function theory (DFT) and electrochemical quartz crystal microbalance (EQCM-D) further confirmed that the structural design of NiCoP@NPC promoted electron transport, Na+ adsorption as well as improved cycling stability. This study is intended to provide a new idea for the in-situ confined synthesis of metal phosphides electrodes with stable performance and structure.

Enhanced Uranium Extraction via Charge Dynamics and Interfacial Polarization in MoS2/GO Heterojunction Electrodes

The removal of uranyl ions (UO2 2+) from water is challenging due to their chemical stability, low concentrations, complex water matrix, and technical limitations in extraction and separation. Herein, a novel molybdenum disulfide/graphene oxide heterojunction (MoS2/GO-H) is developed, serving as an effective electrode for capacitive deionization (CDI). By combining the inherent advantages of electroadsorption and electrocatalysis, an innovative electroadsorption-electrocatalysis system (EES) strategy is introduced. This system utilizes interface polarization at the MoS2 and GO interface, creating an additional electric field that significantly influences carrier behavior. The MoS2/GO-H electrode, with its extraordinary adsorption capacity of 805.57 mg g-1 under optimal conditions, effectively treated uranium-laden wastewater from a mine, achieving over 90% removal efficiency despite the presence of numerous competing ions at concentrations significantly higher than UO2 2+. Employing density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations, it is found that the MoS2/GO-H total charge density at the Fermi level, enhanced by interfacial polarization, surpasses that of separate MoS2 and GO, markedly boosting conductivity and electrocatalytic effectiveness.

Selective Capacitive Recovery of Rare-Earth Ions from Wastewater over Phosphorus-Modified TiO2 Cathodes via an Electro-Adsorption Process

Large amounts of wastewater containing low-concentration (<10 ppm) rare-earth ions (REIs) are discharged annually in China's rare-earth mining and processing industry, resulting in severe environmental pollution and economic losses. Hence, achieving efficient selective recovery of low-concentration REIs from REIs-containing wastewater is essential for environmental protection and resource recovery. In this study, a pseudocapacitance system was designed for highly efficient capacitive selective recovery of REIs from wastewater using the titanium dioxide/P/C (TiO2/P/C) composite electrode, which exhibited over 99% recovery efficiency for REIs, such as Eu3+, Dy3+, Tb3+, and Lu3+ in mixed solution. This system maintained high efficiency and more than 90 times the enrichment concentration of REIs even after 100 cycles. Ti4+ of TiO2 was reduced to Ti3+ of Ti3O5 under forward voltage in the system, which trapped the electrons of phosphorus site and caused it to be oxidized to phosphate with a strong affinity for REIs, thus improving the selectivity of REIs. Under reverse voltage, Ti3O5 was oxidized to TiO2, which transferred electrons to phosphate and transformed to the phosphorus site, resulting in the desorption and enrichment of REIs and the regeneration of the electrode. This study provides a promising method for the efficient recovery of REIs from wastewater.

Engineering Faradaic Electrode Materials for High-Efficiency Water Desalination

Water desalination technologies play a key role in addressing the global water scarcity crisis and ensuring a sustainable supply of freshwater. In contrast to conventional capacitive deionization, which suffers from limitations such as low desalination capacity, carbon anode oxidation, and co-ion expulsion effects of carbon materials, the emerging faradaic electrochemical deionization (FDI) presents a promising avenue for enhancing water desalination performance. These electrode materials employed faradaic charge-transfer processes for ion removal, achieving higher desalination capacity and energy-efficient desalination for high salinity streams. The past decade has witnessed a surge in the advancement of faradaic electrode materials and considerable efforts have been made to explore optimization strategies for improving their desalination performance. This review summarizes the recent progress on the optimization strategies and underlying mechanisms of faradaic electrode materials in pursuit of high-efficiency water desalination, including phase, doping and vacancy engineering, nanocarbon incorporation, heterostructures construction, interlayer spacing engineering, and morphology engineering. The key points of each strategy in design principle, modification method, structural analysis, and optimization mechanism of faradaic materials are discussed in detail. Finally, this work highlights the remaining challenges of faradaic electrode materials and present perspectives for future research.

Achieving Exceptional Volumetric Desalination Capacity Using Compact MoS2 Nanolaminates

Capacitive deionization (CDI) has emerged as a promising technology for freshwater recovery from low-salinity brackish water. It is still inapplicable in specific scenarios (e.g., households, islands, or offshore platforms) due to too low volumetric adsorption capacities. In this study, a high-density semi-metallic molybdenum disulfide (1T'-MoS2) electrode with compact architecture obtained by restacking of exfoliated nanosheets, which achieve high capacitance up to ≈277.5 F cm-3 under an ultrahigh scan rate of 1000 mV s-1 with a lower charge-transfer resistance and nearly tenfold higher electrochemical active surface area than the 2H-MoS2 electrode, is reported. Furthermore, 1T'-MoS2 electrode demonstrates exceptional volumetric desalination capacity of 65.1 mgNaCl cm-3 in CDI experiments. Ex situ X-ray diffraction (XRD) reveal that the cation storage mechanism with the dynamic expansion of 1T'-MoS2 interlayer to accommodate cations such as Na+, K+, Ca2+, and Mg2+, which in turn enhances the capacity. Theoretical analysis unveils that 1T' phase is thermodynamically preferable over 2H phase, the ion hydration and channel confinement also play critical role in enhancing ion adsorption. Overall, this work provides a new method to design compact 2D-layered nanolaminates with high-volumetric performance for CDI desalination.

Selective Capacitive Removal of Pb2+ from Wastewater over Biochar Electrodes by Zinc Regulation

Biochar materials have shown great potential for broad catalytic application. However, using these materials in the capacitive deionization technology (CDI) system for heavy metal removal still faces a significant challenge due to their low specific capacity and removal capability. Here, a comprehensive regulation on the interfacial/bulk electrochemistry of biochar by Zn doping is reported, which suggests a high renewable capacity (20 mg g-1) and outstanding selective capacitive removal ability (SCR) of Pb2+ from leachate. The SCR efficiency of Pb2+ is as high as 99% compared to K+ (8%), Na+ (13%), and Cd2+ (37%). This work proves that the doped Zn on the biochar can combine with OH- generated by water splitting to form M─OH bonds, which is beneficial for improving the specific capacity. Significantly, the relationship between double-layer capacitance and pseudo-capacitance can also be optimized by regulating the content of Zn, leading to different removal abilities of heavy metals. Therefore, this work offers insights into charge-storage kinetics, which provide valuable guidelines for designing and optimizing the biochar electrode for broader environmental applications.

Oxygen-containing functional groups in Fe3O4@three-dimensional graphene nanocomposites for enhancing H2O2 production and orientation to 1O2 in electro-Fenton

In electro-Fenton (EF), development of a bifunctional electrocatalyst to realize simultaneous H2O2 generation and activation efficiently for generating reactive species remains a challenge. In particular, a nonradical-mediated EF is more favorable for actual wastewater remediation, and deserves more attention. In this study, three-dimensional graphene loaded with Fe3O4 nanoparticles (Fe3O4@3D-GNs) with abundant oxygen-containing functional groups (OFGs) was synchronously synthesized using a NaCl-template method and served as a cathode to establish a highly efficient and selective EF process for contaminant degradation. The amounts of OFGs can be effectively modulated via the pyrolysis temperature to regulate the 2e- oxygen reduction reaction activity and reactive oxygen species (ROS) production. The optimized Fe3O4@3D-GNs synthesized at 750 °C (Fe3O4@3D-GNs-750) with the highest -C-O-C and -C꞊O group ratios exhibited the maximum H2O2 and 1O2 yields during electrocatalysis, thus showing remarkable versatility for eliminating organic contaminants from surface water bodies. Experiments and theoretical calculations have demonstrated the dominant role of -C-O-C in generating H2O2 and the positive influence of -C꞊O sites on the production of 1O2. Moreover, the surface-bound Fe(II) favors the generation of surface-bound •OH, which steers a more favorable oxidative conversion of H2O2 to 1O2. Fe3O4@3D-GNs were proven to be less pH-dependent, low-energy, stable, and recyclable for practical applications in wastewater purification. This study provides an innovative strategy to engineer active sites to achieve the selective electrocatalysis for eliminating pollution and reveals a novel perspective for 1O2-generation mechanism in the Fenton reaction.

Cation-exchange fibers and silver nanoparticles-modified carbon electrodes for selective removal of hardness ions and simultaneous deactivation of microorganisms in capacitive deionization

The hardness and microorganism contamination are common problems of water quality around the world. Capacitive deionization (CDI) is a much-discussed solution to help solve the water crisis by providing efficient water softening while killing microorganism. Carboxylic (Na) cation-exchange fiber (CCEF) is an adsorbent material with good affinity for hardness ions. Silver nanoparticles (AgNPs) is a broad-spectrum microbicide. In this paper, the CCEF modified activated carbon (CCEF-AC) was used as cathode and showed excellent hardness ion adsorption selectivity at the optimum CCEF doping level (αCa2+/Na of 15.0, αMg2+/Na of 13.5). Its electrosorption capacity of Ca2+ reached 311 μmol/g, much higher than that of the AC cathode (188 μmol/g). It also showed good regenerable performance, retaining over 85 % of Ca2+ electrosorption capacity after 50 cycles stability test. The activated carbon modified with AgNPs (AC-Ag) was used as anode. When enhanced by an electric field, it could kill bacteria and microalgae with over 99 % and 90 % inhibition rates, respectively. This work has opened up a new way to simultaneously remove multiple pollutants (organic or inorganic) from water.

Sodium lignosulfonate/graphene composites for efficient desalination by incorporating CoS to control pore size

The phenomenon of overlapping double layers due to micropores inhibits capacitive deionization performance, which is improved by increasing the pore size. In this study, a novel ternary composite electrode (sodium lignosulfonate/reduced graphene oxide/cobalt sulfide, LGC) was designed using a two-step hydrothermal method. CoS with high pseudocapacitance modifies sodium lignosulfonate and graphene connected by hydrogen bonding, benefiting from the constitutive steric structure. The electrochemical performance was significantly enhanced, and the desalination capacity substantially improved. The LGC electrode specific capacitance was as high as 354.47 F g-1 at a 1 A g-1 current density. The desalination capacity of the capacitive deionization device comprising LGC and activated carbon in 1 M NaCl electrolyte reached 28.04 mg g-1 at an operating condition of 1.2 V, 7 mL min-1. Additionally, the LGC electrodes degraded naturally post the experiment by simply removing the CoS, suggesting that the LGC composites are promising material for capacitive deionization electrodes.

Pseudocapacitance-Induced Synaptic Plasticity of Tribo-Phototronic Effect Between Ionic Liquid and 2D MoS2

Contact-induced electrification, commonly referred to as triboelectrification, is the subject of extensive investigation at liquid-solid interfaces due to its wide range of applications in electrochemistry, energy harvesting, and sensors. This study examines the triboelectric between an ionic liquid and 2D MoS2 under light illumination. Notably, when a liquid droplet slides across the MoS2 surface, an increase in the generated current and voltage is observed in the forward direction, while a decrease is observed in the reverse direction. This suggests a memory-like tribo-phototronic effect between ionic liquid and 2D MoS2 . The underlying mechanism behind this tribo-phototronic synaptic plasticity is proposed to be ion adsorption/desorption processes resulting from pseudocapacitive deionization/ionization at the liquid-MoS2  interface. This explanation is supported by the equivalent electrical circuit modeling, contact angle measurements, and electronic band diagrams. Furthermore, the influence of various factors such as velocity, step size, light wavelength and intensity, ion concentration, and bias voltage is thoroughly investigated. The artificial synaptic plasticity arising from this phenomenon exhibits significant synaptic features, including potentiation/inhibition, paired-pulse facilitation/depression, and short-term memory (STM) to long-term memory (LTM) transition. This research opens up promising avenues for the development of synaptic memory systems and intelligent sensing applications based on liquid-solid interfaces.

ReaxFF molecular dynamics of graphene oxide/NaCl aqueous solution interfaces

In this work, the interaction of NaCl aqueous solution with graphene (G), graphene oxide (GO), and graphite oxide (GTO) is studied using the ReaxFF module of Amsterdam Modeling Suite (AMS) software. We consider four models using the NaCl aqueous solution, containing a graphene sheet (G), a single sheet of GO with epoxide and hydroxyl groups on its surface, 4 layers of GO to model GTO, and a bulk NaCl solution as a reference. The structural and dynamical properties of G, GO, and GTO were quantified by analyzing the functional groups, radial distribution functions, density profiles and diffusivities of water and ions. Due to the reactive force field, the systems underwent spontaneous modification of surface functional groups during the first 750 ps after which the structure stabilizes (the energy stabilizes in less than 400 ps). Pristine graphene in contact with the NaCl solution formed hydroxyl groups on the edges, i.e., converted to partially reduced graphene oxide. The epoxy groups (Oe) on the initial GO were rather unstable, leading to a reduction of their number, however, there was an increase in the number of hydroxyl groups (Oh), mainly at the edges. The interactions of NaCl with the carbon-based sheets are rather weak, including GO and GTO which are decorated with numerous functional groups. Diffusion coefficients of water agree with the available data, but discrepancies in Na+ and Cl- diffusivity compared to other references underscore the need for further development in the dynamic parameters of the reactive force field used. In essence, our research provides specific data previously unreported, laying a foundation for advancing water desalination system design. The study's novelty lies in its realistic approach to graphene/graphene oxide modification, comprehensive characterization, and the application of the reactive force field to explore the graphene oxide-NaCl aqueous interface, contributing to the development of a practical membrane system for water desalination.

Current technologies for heavy metal removal from food and environmental resources

Exposure to heavy metals in water and food poses a significant threat to human well-being, necessitating the efficient removal of these contaminants. The process of urban development exacerbates heavy metal pollution, thereby increasing risks to both human health and ecosystems. Heavy metals have the capacity to enter the food chain, undergo bioaccumulation and magnify, ultimately resulting in adverse effects on human health. Therefore, implementing effective pollution control measures and adopting sustainable practices are crucial for mitigating exposure and associated health risks. Various innovative approaches, including adsorption, ion exchange, and electrochemical technology, are currently being actively investigated to cope with the issue of heavy metal contamination. These innovative methods offer benefits such as efficient recycling, cost-effectiveness and environmental friendliness. In this review, we summarize recent advances for removing heavy metals from water, soil and food, providing valuable guidance for environmental engineers and researchers seeking to address contamination challenges.

Recent Progress and Challenges in Faradic Capacitive Desalination: From Mechanism to Performance

Due to substantial consumption and widespread contamination of the available freshwater resources, green, economical, and sustainable water recycling technologies are urgently needed. Recently, Faradic capacitive deionization (CDI), an emerging desalination technology, has shown great desalination potential due to its high salt removal ability, low consumption, and hardly any co-ion exclusion effect. However, the ion removal mechanisms and structure-property relationships of Faradic CDI are still unclear. Therefore, it is necessary to summarize the current research progress and challenges of Faradic CDI. In this review, the recent progress of Faradic CDI from five aspects is systematically reviewed: cell architectures, desalination mechanisms, evaluation indicators, operation modes, and electrode materials. The working mechanisms of Faradic CDI are classified as insertion reaction, conversion reaction, ion-redox species interaction, and ion-redox couple interaction in the electrolytes. The intrinsic and desalination properties of a series of Na+ and Cl- capturing materials are described in detail in terms of design concepts, structural analysis, and synthesis modulation. In addition, the effects of different cell architectures, operation modes, and electrode materials on the desalination performance of Faradic CDI are also investigated. Finally, the work summarizes the challenges remaining in Faradic CDI and provides the prospects and directions for future development.

Synergistic effect of intercalation and EDLC electrosorption of 2D/3D interconnected architectures to boost capacitive deionization for water desalination via MoSe2/mesoporous carbon hollow spheres

Transition-metal dichalcogenides can be used for capacitive deionization (CDI) via pseudocapacitive ion intercalation/de-intercalation due to their unique two-dimensional (2D) laminar structure. MoS₂ has been extensively studied in the hybrid capacitive deionization (HCDI), but the desalination performance of MoS₂-based electrodes remains only 20-35 mg g^-1 on average. Benefiting from the higher conductivity and larger layer spacing of MoSe₂ than MoS₂, it is expected that MoSe₂ would exhibit a superior HCDI desalination performance. Herein, for the first time, we explored the use of MoSe₂ in HCDI and synthesized a novel MoSe₂/MCHS composite material by utilizing mesoporous carbon hollow spheres (MCHS) as the growth substrate to inhibit the aggregation and improve the conductivity of MoSe₂. The as-obtained MoSe₂/MCHS presented unique 2D/3D interconnected architectures, allowing for synergistic effects of intercalation pseudocapacitance and electrical double layer capacitance (EDLC). An excellent salt adsorption capacity of 45.25 mg g^- 1 and a high salt removal rate of 7.75 mg g^- 1 min^-1 were achieved in 500 mg L^- 1 NaCl feed solution at an applied voltage of 1.2 V in batch-mode tests. Moreover, the MoSe₂/MCHS electrode exhibited outstanding cycling performance and low energy consumption, making it suitable for practical applications. This work demonstrates the promising application of selenides in CDI and provides new insights for ration design of high-performance composite electrode materials.

Ternary-metal Prussian blue analogues as high-quality sodium ion capturing electrodes for rocking-chair capacitive deionization

Prussian blue analogs (PBAs) have gained much attention in the capacitive deionization (CDI) field because of their rigid open structure and good energy storage capacity. However, their desalination performance is still to be improved for practical application. Herein, we reported the NiCoFe ternary-metal PBAs materials and explored their application as Na⁺ capturing electrode in rocking-chair capacitive deionization (RCDI) system. On the one hand, the introduction of Ni²⁺ into CoFe PBA can effectively reduce the lattice changes in the (dis)charging process.On the other hand, the RCDI system with symmetrical structure could avoid the performance deficiency caused by the unbalanced capacity of common HCDI system. Due to the rationalized RCDI cell configuration and ternary-metal PBAs with improved stability, the NiCoFe-PBAs-based RCDI exhibits amazing desalination performance with maximum capacity of 131.4 mg·g^-1 and rate of 0.46 mg·g^-1·s^-1 as well as optimum stability with 90.7 % capacity retention over 300 cycles, surpassing those of PBAs based CDI system reported previously. The special strategy in this work offers inspiration via optimizing the cell structure and electrode materials for the promising development of CDI systems.

Local Electric Field Induced by Atomic-Level Donor-Acceptor Couple of O Vacancies and Mn Atoms Enables Efficient Hybrid Capacitive Deionization

Transition metal oxides suffer from slow salt removal rate (SRR) due to inferior ions diffusion ability in hybrid capacitive deionization (HCDI). Local electric field (LEF) can efficiently improve the ions diffusion kinetics in thin electrodes for electrochemical energy storage. Nevertheless, it is still a challenge to facilitate the ions diffusion in bulk electrodes with high loading mass for HCDI. Herein, this work delicately constructs a LEF via engineering atomic-level donor (O vacancies)-acceptor (Mn atoms) couples, which significantly facilitates the ions diffusion and then enables a high-performance HCDI. The LEF boosts an extended accelerated ions diffusion channel at the particle surface and interparticle space, resulting in both remarkably enhanced SRR and salt removal capacity. Convincingly, the theoretical calculations demonstrate that electron-enriched Mn atoms center coupled with an electron-depleted O vacancies center is formed due to the electron back-donation from O vacancies to adjacent Mn centers. The resulted LEF efficiently reduce the ions diffusion energy barrier. This work sheds light on the effect of atomic-level LEF on improving ions diffusion kinetics at high loading mass application and paves the way for the design of transition metal oxides toward high-performance HCDI applications.

Capacitive deionization of high concentrations of hexavalent chromium using nickel-ferric-layered double hydroxide/molybdenum disulfide asymmetric electrode

To decontaminate wastewater affected by high concentrations of aqueous hexavalent chromium (Cr(VI)) and improve the capability of layered double hydroxide (LDH) as an electrode in the capacitive deionization (CDI) process, nickel-ferric-LDH (NiFe-LDH) and NiFe-LDH/molybdenum disulfide (NiFe/MoS₂) were synthesized using a hydrothermal method. Characterization results indicated that the flower-like cluster framework of MoS₂ was decorated with the NiFe-LDH. Addition of MoS₂ improved the conductivity, capacitance reversibility, charge efficiency, coulombic efficiency, and stability of NiFe/MoS₂. The CDI performance of aqueous Cr(VI) was evaluated using NiFe/MoS₂ and activated carbon as the anode and cathode, respectively. The process reached equilibrium within 240 min. The deionization capacity and removal ratio for Cr(VI) (100 mg/L, 100 mL) were 49.71 mg/g and 99.42 %, respectively, at 1.2 V and 20 mL/min. The isothermal data were accurately described using the Langmuir model, and the theoretical maximum deionization capacity of NiFe/MoS₂ for Cr(VI) was 106.2 mg/g. The interaction mechanisms included electrostatic attraction, surface complexation, and reduction. These findings indicate that NiFe/MoS₂ has feasible applications in practical wastewater treatment for Cr(VI) removal.

Electrosorption performance on graphene-based materials: a review

Due to its unique advantages such as flexible planar structure, ultrahigh specific surface area, superior electrical conductivity and electrical double-layer capacitance in theory, graphene has unparalleled virtues compared with other carbon materials. This review summarizes the recent research progress of various graphene-based electrodes on ion electrosorption fields, especially for water desalination utilizing capacitive deionization (CDI) technology. We present the latest advances of graphene-based electrodes, such as 3D graphene, graphene/metal oxide (MO) composites, graphene/carbon composites, heteroatom-doped graphene and graphene/polymer composites. Furthermore, a brief outlook on the challenges and future possible developments in the electrosorption area are also addressed for researchers to design graphene-based electrodes towards practical application.

Freeing Fluoride Termination of Ti3C2Tx via Electrochemical Etching for High-Performance Capacitive Deionization

Ti3C2Tx MXene is a promising Faradic capacitive deionization (CDI) electrode for high salt removal in future desalination, whereas the surface termination group of fluoride (-F) significantly impedes ion access to Ti3C2 and charge-transfer efficiency. Herein, we propose an electrochemically etched strategy to synthesize -F-free Ti3C2Tx through three-electrode cyclic voltammetry scanning within a narrowed potential window in an alkaline electrolyte. The resulting assembly of an asymmetric electrochemical-etched Ti3C2Tx//activated carbon CDI device can deliver an excellent salt removal capacity of 20.27 mg·g-1 with an adsorption rate of 1.01 mg g-1 min-1 owing to the enhanced hydrophilicity and ion transport. The tiny CDI device is demonstrated, which can generate an electric current during the electrosorption of salt ions, thus facilitating the powering of a red light-emitting diode. This study opens a new avenue for the surface chemistry of Ti3C2Tx and is expected to achieve future applications in desalination and renewable energy.

Removal of heavy metals from aqueous solutions by high performance capacitive deionization process using biochar derived from Sargassum hemiphyllum

Capacitive deionization (CDI) has been considered as an efficient, energy-saving and environmental friendly technology for water treatment. For the practical application of CDI, high-performance electrode materials beyond standard activated carbon should be developed. In this study, biochar derived from brown algae Sargassum hemiphyllum prepared by pyrolysis at 300-700 °C and then used as the CDI electrode to remove Cu(II) from aqueous solutions. According to the findings, the optimal pyrolysis temperature was 700 °C, and the electrosorption capacity of BAB700 was 75-120 mg·g-1 at an applied voltage of 1.2 V across wide range of initial pH, temperatures and ion types. Moreover, BAB700 also exhibited outstanding ability to electrosorb other heavy metals (Zn(II), Ni(II), and Cd(II)). In addition, the BAB700 retained the Cu(II) removal efficiency of 70 % in 10 cycles. Cu(II) in actual water is completely eliminated with great reproducibility, resulting in a high degree of applicability for water treatment.

Enhanced capacitive deionization properties of activated carbon doped with carbon nanotube-bridged molybdenum disulfide

The shortage of freshwater supplies has restricted societal development. Capacitive deionization (CDI) is an emerging technology for desalination of seawater or brackish water, the performance of which is highly dependent on electrode materials. In this work, a molybdenum disulfide/carbon nanotube composite (CNTs-b-MoS₂) with high capacitance was successfully synthesized using a hydrothermal method. The composite exhibited a specific capacitance of 112.79 F g^-1. To reduce costs and determine the practicality of using CNTs-b-MoS₂ for CDI, we combined activated carbon (AC) with CNTs-b-MoS₂ as a CDI electrode. The research demonstrated that after doping with 5% (mass ratio) CNTs-b-MoS₂, the specific capacitance and electrosorption capacity of AC were significantly improved and the maximum desalination capacity of CNTs-b-MoS₂/AC reached 8.19 mg g^-1. The low dosage of CNTs-b-MoS₂ combined with the high specific surface area of AC avoided the shortcomings of CNTs-b-MoS₂, namely low specific surface area and high cost. Moreover, the outstanding conductivity of CNTs-b-MoS₂ improved the conductivity and enhanced the adsorption capacity of AC, giving CNTs-b-MoS₂/AC potential as an advanced, low-cost CDI electrode material.

Interfacial Charge-Modulated Multifunctional MoS2/Ti3C2Tx Penetrating Electrode for High-Efficiency Freshwater Production

Freshwater production is critical in terms of solving the global water shortage. Aiming at improving freshwater production capability and ensuring its quality, an interfacial charge-modulated MoS₂/Ti₃C₂T_x-modified carbon fiber (CF/MoS₂/Ti₃C₂T_x) penetrating electrode is designed. To maximize the desalination and degradation efficiencies of CF/MoS₂/Ti₃C₂T_x, a photocatalytic component is introduced into the membrane capacitive deionization (PMCDI) device. High desalination capability is derived from the lamellar architecture structure of MoS₂/Ti₃C₂T_x. Meanwhile, excellent degradation performance is due to the formation of two photoelctrocatalytic activity centers, directionally generating singlet oxygen (¹O₂) and hydroxyl radical (^•OH). The intercalated Cl^- (desalination) as the electron transfer bridge optimizes the charge distribution of MoS₂/Ti₃C₂T_x, reinforcing the photoelectrocatalytic activity (degradation). The formation of the electron-deficient (desalination) and electron-rich (regeneration) regions at the terminated O atom of Ti₃C₂T_x accelerate the generations of ^•OH and ¹O₂, respectively. In perspective, a mutual promotion process of desalination and degradation is achieved for high-efficiency production of high-quality freshwater.

Activated Carbon Aerogel as an Electrode with High Specific Capacitance for Capacitive Deionization

In this study, carbon aerogels (CAs) were synthesized by the sol-gel method, using environmentally friendly glucose as a precursor, and then they were further activated with potassium hydroxide (KOH) to obtain activated carbon aerogels (ACAs). After the activation, the electrochemical performance of the ACAs was significantly improved, and the specific capacitance increased from 19.70 F·g−1 to 111.89 F·g−1. Moreover, the ACAs showed a stronger hydrophilicity with the contact angle of 118.54° compared with CAs (69.31°). When used as an electrode for capacitive deionization (CDI), the ACAs had not only a better diffuse electric double layer behavior, but also a lower charge transfer resistance and intrinsic resistance. Thus, the ACA electrode had a faster CDI desalination rate and a higher desalination capacity. The unit adsorption capacity is three times larger than that of the CA electrode. In the desalination experiment of 100 mg·L−1 sodium chloride (NaCl) solution using a CDI device based on the ACA electrode, the optimal electrode spacing was 2 mm, the voltage was 1.4 V, and the flow rate was 30 mL·min−1. When the NaCl concentration was 500 mg·L−1, the unit adsorption capacity of the ACA electrode reached 26.12 mg·g−1, much higher than that which has been reported in many literatures. The desalination process followed the Langmuir model, and the electro-sorption of the NaCl was a single layer adsorption process. In addition, the ACA electrode exhibited a good regeneration performance and cycle stability.

Surfactant-assisted self-assembly of flower-like ultrathin vanadium disulfide nanosheets for enhanced hybrid capacitive deionization

Increasing the salt adsorption capacity (SAC) and durability of electrode materials for hybrid capacitive deionization (HCDI) remain grand challenges. Herein, highly electro-adsorptive and durable vanadium disulfide (VS₂) electrode material obtained by a surfactant-assisted hydrothermal method is reported. The distinct three-dimensional flower-like architecture and ultrathin thickness of VS₂ nanosheets play a vital role in boosting HCDI performance by exposing a large number of accessible adsorption sites and facilitating the mass transfer of sodium ions. When used in the HCDI system, the flower-like VS₂ electrode delivers a high salt adsorption capacity of 72 mg g^-1 in 500 mg L^-1 NaCl solution at 1.6 V, outperforming the bulk VS₂ counterpart with a relatively increased thickness of nanosheets. Moreover, after 10 h of cycling test, the SAC of the flower-like VS₂-based HCDI system remains at 93 % of the initial value, showing excellent operation stability. This surfactant-assisted morphology engineering of VS₂ nanosheets with ultrathin thickness and unique three-dimensional architecture provides new insight into designing layered electrode materials for efficient HCDI.

Highly Selective Recovery of Phosphorus from Wastewater via Capacitive Deionization Enabled by Ferrocene-polyaniline-Functionalized Carbon Nanotube Electrodes

While capacitive deionization (CDI) is a promising technology for the recovery of nutrients from wastewater, a selective recovery of phosphate from the wastewater containing high concentrations of competing ions is still a huge challenge. Herein, we reported a ferrocene-polyaniline-functionalized carbon nanotube (Fc-PANI/CNT) electrode prepared through amidation reaction and chemical oxidation polymerization, aiming for a highly selective recovery of phosphorus from wastewater. The Fc-PANI/CNT electrode with a unique structure and high conductivity could efficiently adsorb phosphate ions from complex synthetic wastewater with a nearly 100% selectivity, mainly because the integration of ferrocene and an amide bond in Fc-PANI resulted in an enhanced charge transfer (Faradaic reactions) and a strong hydrogen bonding interaction with phosphate ions in its oxidized state. Density functional theory calculations showed that the binding energies of the oxidized Fc-PANI with HPO₄^2- and H₂PO₄^- were much greater than those of the oxidized Fc-PANI with other competing anions. The affinity of Fc-PANI/CNTs with phosphate can be controlled electrochemically based on the synergetic effects of Faradaic reactions and hydrogen bonding, enabling a selective recovery of phosphate through charging/discharging cycles. The phosphate adsorption capacity reached up to 35 mg PO₄^3- g^-1 in a NaCl/Na₂SO₄/NaNO₃/NaH₂PO₄ complex mixture at 1.2 V, outperforming most of the other reported CDI systems. The Fc-PANI/CNT electrode also exhibited a decent regeneration ability and durability during repeated CDI tests, demonstrating a great potential for the application of selective recovery and enrichment of phosphate from wastewater.

Co-Co3O4 encapsulated in nitrogen-doped carbon nanotubes for capacitive desalination: Effects of nano-confinement and cobalt speciation

Capacitive deionization (CDI) has gained increasing attention as an environmentally friendly and energy-efficient technology for brackish water desalination. However, traditional CDI electrodes still suffer from low salt adsorption capacity and unsatisfactory reusability, which inhibit its application for long-term operations. Herein, we present a facile and effective approach to prepare Co and Co₃O₄ nanoparticles co-incorporating nitrogen-doped (N-doped) carbon nanotubes (Co-Co₃O₄/N-CNTs) via a pyrolysis route. The Co-Co₃O₄ nanoparticles were homogeneously in-situ encapsulated in the inner channels of the conductive CNTs to form a novel and efficient CDI electrode for the first time. The encapsulation of Co-Co₃O₄ nanoparticles in CNTs not only inhibits the Co leaching but also significantly enhances the desalination capacity. The morphology, structure, and capacitive desalination properties of the Co-Co₃O₄/N-CNTs were thoroughly characterized to illuminate the nano-confinement effects and the key roles of the interaction between cobalt species in the CDI performance. The co-existing metallic cobalt and cobalt oxides act as the roles of effective active sites in the CDI performance. As a consequence, the optimum Co-Co₃O₄/N-CNTs electrode displays an outstanding desalination capacity of 66.91 mg NaCl g^-1 at 1.4 V. This work provides insights for understanding the nano-confinement effects and the key roles of the interaction between cobalt species on the CDI performance.

Selective removal of Sr(II) from saliferous radioactive wastewater by capacitive deionization

⁹⁰Sr-containing radioactive wastewater during Fukushima nuclear accident (FNA) aroused extensive consideration for its disposal. Massive coexisted Na⁺ ions seriously inhibited Sr²⁺ removal, aggravating the expenditure of radioactive wastewater treatment. Herein, a chestnut shell derived porous carbon material modified with aryl diazonium salt (ADS) of sodium 4-aminoazobenzene-4'-sulfonate (SPAC) was developed as capacitive deionization electrode for selective removal of Sr²⁺ from saliferous radioactive wastewater. Based on ADS modification, the Sr²⁺ electrosorption capacity of SPAC electrode was improved to 33.11 mg g^-1 with fast ion removal rate of 2.89 mg g^-1 min^-1, comparing with only 16.10 mg g^-1 before modification. The isothermal adsorption and kinetics by SPAC electrode fitted well with Langmuir and pseudo-second-order model, achieving a maximum Sr²⁺ electrosorption capacity of 58.21 mg g^-1, superior cycling stability, and excellent charge efficiency (77.63%). Fascinatingly, the SPAC electrode exhibited superhigh Sr²⁺ selectivity of 70.65 against Na⁺ in Na⁺-Sr²⁺ mixed solution with molar ratio of Na⁺:Sr²⁺ as 20:1. Density functional theory (DFT) simulation, combining with electrochemical and spectral analyses, revealed that the high overlap of electron cloud between Sr²⁺ ion and anionic sulfonic group (-SO₃^-) provided SPAC with remarkable selectivity of Sr²⁺ ion, and illustrated the ion-swapping mechanism of Sr²⁺ selectivity.

Carbon Nanoarchitectonics with Bi Nanoparticle Encapsulation for Improved Electrochemical Deionization Performance

Electrochemical deionization (EDI) is hopefully the next generation of water treatment technology. Bismuth (Bi) is a promising anode material for EDI, due to its high capacity and selectivity toward Cl^-, but the large volume expansion and severe pulverization aggressively attenuated the EDI cycling performance of Bi electrodes. Herein, carbon-layer-encapsulated nano-Bi composites (Bi@C) were prepared by a simple pyrolysis method using a Bi-based metal-organic framework as a precursor. Bi nanoparticles are uniformly coated within the carbon layer, in which the Bi-O-C bond enhances the interaction between Bi and C. Such a structure effectively relieves the stress caused by volume expansion by the encapsulation effect of the carbon layer. Moreover, the introduction of a carbon skeleton provides a conductive network. As a consequence, the Bi@C composite delivered excellent electrochemical performance with a capacity of 537.6 F g^-1 at 1 mV s^-1. The Cl^- removal capacity was up to 133.5 mg g^-1 at 20 mA g^-1 in 500 mg L^-1 NaCl solution. After 100 cycles, the Bi@C electrode still maintains 71.8% of its initial capacity, which is much higher than the 26.3% of the pure Bi electrode. This study provides a promising strategy for improving EDI electrode materials.

3D Heterostructure Constructed by Few-Layered MXenes with a MoS2 Layer as the Shielding Shell for Excellent Hybrid Capacitive Deionization and Enhanced Structural Stability

Two-dimensional (2D) layered transition-metal carbides (MXenes) are attractive faradic materials for an efficient capacitive deionization (CDI) process owing to their high capacitance, excellent conductivity, and remarkable ion storage capacity. However, the easy restacking property and spontaneous oxidation in solution by the dissolved oxygen of MXenes greatly restrict their further application in the CDI domain. Herein, a three-dimensional (3D) heterostructure (MoS₂@MXene) is rationally designed and constructed, integrating the collective advantages of MXene flakes and MoS₂ nanosheets through the hydrothermal method. In such a design, the well-dispersed MXene flakes can effectively reduce the aggregation of MoS₂ nanosheets, boost electrical conductivity, and provide efficient charge transfer paths. Furthermore, MoS₂ nanosheets as the high-capacity interlayer spacer can prevent the self-restacking of MXene flakes and provide more active sites for ion intercalation. Meanwhile, the strong chemical interactions between MXene flakes and MoS₂ nanosheets contribute to accelerating the charge transfer kinetics and enhancing structural stability. Consequently, the resulting MoS₂@MXene heterostructure electrode possesses high specific capacitance (171.4 F g^-1), fast charge transfer and permeation rate, abundant Na⁺ diffusion channels, and superior electrochemical stability. Moreover, the hybrid CDI cell (AC//MoS₂@MXene) with AC as the anode and MoS₂@MXene as the cathode delivers outstanding desalination capacity (35.6 mg g^-1), rapid desalination rate (2.6 mg g^-1 min^-1), excellent charge efficiency (90.2%), and good cyclic stability (96% retention rate). Most importantly, the MoS₂@MXene electrode can keep good structural integrity after the long-term repeated desalination process due to the effective shielding effect of the MoS₂ layer to protect MXenes from being further oxidized. This work presents the flexible structural engineering to realize excellent ion transfer and storage process by constructing the 3D heterostructure.

Synthesis and Photoluminescence Properties of MoS2/Graphene Heterostructure by Liquid-Phase Exfoliation

Here, we report the synthesis of MoS2/graphene heterostructure in single-stage, liquid-phase exfoliation using a 7:3 isopropyl alcohol/water mixture. Further, the synthesized heterostructure was characterized using UV-visible and micro-Raman spectroscopies, transmission electron microscopy (TEM), and dynamic light scattering (DLS) analysis. UV-visible and micro-Raman analyses confirmed that the synthesized heterostructure had mostly few-layered (two-to-four sheets) MoS2. The photophysical properties of the heterostructure were analyzed using steady-state and time-resolved luminescence techniques. Enhanced photoluminescence was observed in the case of the heterostructure probably due to an increase in the defect sites or reduction in the rate of nonradiative decay upon formation of the sandwiched heterostructure. Applications of this heterostructure for fluorescence live-cell imaging were carried out, and the heterostructure demonstrated a better luminescence contrast compared to its individual counterpart MoS2 in phosphate-buffered saline (PBS).

Bismuth oxychloride nanostructure coated carbon sponge as flow-through electrode for highly efficient rocking-chair capacitive deionization

Rocking-chair capacitive deionization (RCDI), as the next generation technique of capacitive deionization, has thrived to be one of the most promising strategies in the desalination community, yet was hindered mostly by its relatively low desalination rate and stability. Motivated by the goal of simultaneously enhancing the desalination rate and structural stability of the electrode, this paper reports an anion-driven flow-through RCDI (AFT-RCDI) system equipped with BiOCl nanostructure coated carbon sponge (CS@BiOCl for short; its backbone is derived from commercially available melamine foam with minimum capital cost) as the flow-through electrode. Owning to the rational design of the composite electrode material with minimum charge transfer resistance and ultrahigh structure stability as well as the superior flow-through cell architecture, the AFT-RCDI displays excellent desalination performance (desalination capacity up to 107.33 mg g^-1; desalination rate up to 0.53 mg g^-1s^-1) with superior long-term stability (91.75% desalination capacity remained after 30 cycles). This work provides a new thought of coupling anion capturing electrode with flow-through cell architecture and employing a low-cost CS@BiOCl electrode with commercially available backbone material, which could shed light on the further development of low-cost electrochemical desalination systems.

Separation of Rare-Earth Ions from Mine Wastewater Using B12S Nanoflakes as a Capacitive Deionization Electrode Material

In this study, nanoflakes of B₁₂S were fabricated by plasma-assisted reaction of sulfur dichloride in an ionic liquid at room temperature using europium boride as a hard template. The nanoflakes had an average width and thickness of about 3 ₁urn and 9.6 nm, respectively, and a large specific surface area of 1197.2 m² g ¹. They behaved like typical electric double-layer capacitors with a capacitance of 201.2 F g ¹ at 0.2 mA cm ² During capacitive deionization to recover rare-earth ions, the nanoflakes had higher adsorption selectivity for Sm³⁺ than for other competing ions present in real mine waste water. This is due to the strong interaction of the electron-concentered S-groups (S''') of the nanoflakes with S m³⁺. This provides an alternative to construct efficient systems to specifically remove Sm³⁺ from aqueous solution using B₁₂S nanoflakes. This process demonstrates that other boron sulfide compounds can be used to recover valuable ions by capacitive deionization.

Reversible adsorption and desorption of PFAS on inexpensive graphite adsorbents via alternating electric field

Per- and polyfluoroalkyl substances (PFAS) have been extensively utilized in practical applications that include surfactants, lubricants, and firefighting foams due to their thermal stability and chemical inertness. Recent studies have revealed that PFAS were detected in groundwater and even drinking water systems which can cause severe environmental and health issues. While adsorbents with a large specific surface area have demonstrated effective removal of PFAS from water, their capability in desorbing the retained PFAS has been often neglected despite its critical role in regeneration for reuse. Further, they have demonstrated a relatively lower adsorption capacity for PFAS with a short fluoroalkyl chain length. To overcome these limitations, electric field-aided adsorption has been explored. In this work, reversible adsorption and desorption of PFAS dissolved in water upon alternating voltage is reported. An inexpensive graphite adsorbent is fabricated by using a simple press resulting in a mesoporous structure with a BET surface area of 132.9 ± 10.0 m2 g-1. Electric field-aided adsorption and desorption experiments are conducted by using a custom-made cell consisting of two graphite electrodes placed in parallel in a polydimethylsiloxane container. Unlike the conventional sorption process, a graphite electrode exhibits a higher adsorption capacity for PFAS with a short fluoroalkyl chain (perfluoropentanoic acid, PFPA) in comparison to that with a long fluoroalkyl chain (perfluorooctanoic acid, PFOA). Upon alternating the voltage to a negative value, the retained PFPA or PFOA is released into the surrounding water. Finally, we engineered a device module mounted on a gravity-assisted apparatus to demonstrate electrosorption of PFAS and collection of high purity water.

α-Fe2O3/graphene oxide powder and thin film nanocomposites as peculiar photocatalysts for dye removal from wastewater

In this study, hematite graphene oxide (αFe₂O₃-GO) powder nanocomposites and thin-film hematite graphene oxide (αFe₂O₃-GO) were synthesized for application in the removal of Rhodamine B (RhB) from textile wastewater. αFe₂O₃-GO nanomaterials were placed onto the FTO substrate to form a thin layer of nanocomposites. Different analysis including XRD, FTIR, Raman spectra, XPS, and FESEM were done to analyze the morphology, structure, and properties of the synthesized composites as well as the chemical interactions of αFe₂O₃ with GO. The photocatalytic performance of two synthesized composites was compared with different concentrations of αFe₂O₃-GO. The results showed that powder nanocomposites are more effective than thin-film composites for the removal of RhB dye. αFe₂O₃-GO-5% powder nanocomposites removed over 64% of dye while thin-film nanocomposites had less removal efficiencies with just under 47% removal rate. The reusability test was done for both materials in which αFe₂O₃-GO-5% powder nanocomposites removed a higher rate of dye (up to 63%) in more cycles (6 cycles).

Recent Advances in Faradic Electrochemical Deionization: System Architectures versus Electrode Materials

Capacitive deionization (CDI) is an energy-efficient desalination technique. However, the maximum desalination capacity of conventional carbon-based CDI systems is approximately 20 mg g^-1, which is too low for practical applications. Therefore, the focus of research on CDI has shifted to the development of faradic electrochemical deionization systems using electrodes based on faradic materials which have a significantly higher ion-storage capacity than carbon-based electrodes. In addition to the common symmetrical CDI system, there has also been extensive research on innovative systems to maximize the performance of faradic electrode materials. Research has focused primarily on faradic reactions and faradic electrode materials. However, the correlation between faradic electrode materials and the various electrochemical deionization system architectures, i.e., hybrid capacitive deionization, rocking-chair capacitive deionization, and dual-ion intercalation electrochemical desalination, remains relatively unexplored. This has inhibited the design of specific faradic electrode materials based on the characteristics of individual faradic electrochemical desalination systems. In this review, we have characterized faradic electrode materials based on both their material category and the electrochemical desalination system in which they were utilized. We expect that the detailed analysis of the properties, advantages, and challenges of the individual systems will establish a fundamental correlation between CDI systems and electrode materials that will facilitate future developments in this field.

Capacitive Removal of Fluoride Ions via Creating Multiple Capture Sites in a Modulatory Heterostructure

Fluoride pollution has become a major concern because of its adverse effects on human health. However, the removal capacity of defluorination agents in traditional methods is far from satisfactory. Herein, capacitive removal of F^- ions via creating multiple capture sites in a modulatory heterostructure has been originally demonstrated. The heterostructure of uniformly dispersed Al₂O₃ coating on hollow porous nitrogen-doped carbon frameworks was precisely synthesized by atomic layer deposition. An exceptional F^- ion removal efficiency at 1.2 V (95.8 and 92.9% in 5 and 10 mg/L F^- solutions, respectively) could be finally achieved, with a good regeneration ability after 20 consecutive defluorination cycles. Furthermore, we investigated the removal mechanisms of F^- ions by in situ Raman, in situ X-ray diffraction, and ex situ X-ray photoelectron spectroscopy measurements. The promotional removal capacity was realized by the multiple capture sites of the reversible conversion of Al-F species and the insertion of F^- ions into the carbon skeleton. This work offers an important new pathway and deep understanding for efficient removal of F^- ions from wastewater.