Superlattice Structure from Self-Assembly of High-χ Block Copolymers via Chain Interdigitation

Controlling Anti-Penetration Performance by Post-Grafting of Fluorinated Alkyl Chains onto Polystyrene-block-poly(vinyl methyl siloxane)

Polydimethylsiloxane (PDMS) has been widely used as a surface coating material, which has been reported to possess dynamic omniphobicity to a wide range of both polar and nonpolar solvents due to its high segmental flexibility and mobility. However, such high flexibility and mobility also enable penetration of small molecules into PDMS coatings, which alter the chemical and physical properties of the coating layers. To improve the anti-penetration properties of PDMS, a series of fluorinated alkyl segments are grafted to a diblock copolymer of polystyrene-block-poly(vinyl methyl siloxane) (PS-b-PVMS) using thiol-ene click reactions. This article reports the chemical characterization of these model fluorosilicone block copolymers and uses fluorescence measurements to investigate the dye penetration characteristics of polymer thin films. The introduction of longer fluorinated alkyl chains can gradually increase the anti-penetration properties as the time to reach the maximum fluorescence intensity (tpeak) gradually increases from 11 s of PS-b-PVMS to more than 1000 s of PS-b-P(n-C6F13-VMS). The improvement of anti-penetration properties is attributed to stronger inter-/intrachain interactions, phase segregation of ordered fluorinated side chains, and enhanced hydrophobicity caused by the grafting of fluorinated alkyl chains.

Synthesis and Structural Insight into poly(dimethylsiloxane)-b-poly(2-vinylpyridine) Copolymers

In this study, the use of anionic polymerization for the synthesis of living poly(dimethylsiloxane) or PDMS-Li+, as well as poly(2-vinylpyridine) or P2VP-Li+ homopolymers, and the subsequent use of chlorosilane chemistry in order for the two blocks to be covalently joined leading to PDMS-b-P2VP copolymers is proposed. High vacuum manipulations enabled the synthesis of well-defined materials with different molecular weights (Μ¯n, from 9.8 to 36.0 kg/mol) and volume fraction ratios (φ, from 0.15 to 0.67). The Μ¯n values, dispersity indices, and composition were determined through membrane/vapor pressure osmometry (MO/VPO), size exclusion chromatography (SEC), and proton nuclear magnetic resonance spectroscopy (1H NMR), respectively, while the thermal transitions were determined via differential scanning calorimetry (DSC). The morphological characterization results suggested that for common composition ratios, lamellar, cylindrical, and spherical phases with domain periodicities ranging from approximately 15 to 39 nm are formed. A post-polymerization chemical modification reaction to quaternize the nitrogen atom in some of the P2VP monomeric units in the copolymer with the highest P2VP content, and the additional characterizations through 1H NMR, infrared spectroscopy, DSC, and contact angle are reported. The synthesis, characterization, and quaternization of the copolymer structure are important findings toward the preparation of functional materials with enhanced properties suitable for various nanotechnology applications.

Heating-Induced Switching to Hierarchical Liquid Crystallinity Combining Colloidal and Molecular Order in Zwitterionic Molecules

Hierarchical self-assemblies of soft matter involving triggerable or switchable structures at different length scales have been pursued toward multifunctional behaviors and complexity inspired by biological matter. They require several and balanced competing attractive and repulsive interactions, which provide a grand challenge in particular in the "bulk" state, i.e., in the absence of plasticizing solvents. Here, we disclose that zwitterionic bis-n-tetradecylphosphobetaine, as a model compound, shows a complex thermally switchable hierarchical self-assembly in the solvent-free state. It shows polymorphism and heating-induced reversible switching from low-temperature molecular-level assemblies to high-temperature hierarchical self-assemblies, unexpectedly combining colloidal and molecular self-assemblies, as inferred by synchrotron small-angle X-ray scattering (SAXS). The high-temperature phase sustains birefringent flow, indicating a new type of hierarchical thermotropic liquid crystallinity. The high-temperature colloidal-level SAXS reflections suggest indexation as a 2D oblique pattern and their well-defined layer separation in the perpendicular direction. We suggest that the colloidal self-assembled motifs are 2D nanoplatelets formed by the lateral packing of the molecules, where the molecular packing frustration between the tightly packed zwitterionic moieties and the coiled alkyl chains demanding more space limits the lateral platelet growth controlled by the alkyl stretching entropy. An indirect proof is provided by the addition of plasticizing ionic liquids, which relieve the ionic dense packings of zwitterions, thus allowing purely smectic liquid crystallinity without the colloidal level order. Thus, molecules with a simple chemical structure can lead to structural hierarchy and tunable complexity in the solvent-free state by balancing the competing long-range electrostatics and short-range nanosegregations.

Highly Ordered Porous Inorganic Structures via Block Copolymer Lithography: An Application of the Versatile and Selective Infiltration of the "Inverse" P2VP-b-PS System

A facile and versatile strategy was developed to produce highly ordered porous metal oxide structures via block copolymer (BCP) lithography. Phase separation of poly(2-vinylpyridine)-b-polystyrene (P2VP-b-PS) was induced by solvent vapor annealing in a nonselective solvent environment to fabricate cylindrical arrays. In this work, we thoroughly analyzed the effects of the film thickness, solvent annealing time, and temperature on the ordering of a P2VP-majority system for the first time, resulting in "inverse" structures. Reflectometry, atomic force microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy were used to characterize the formation of the highly ordered BCP morphology and the subsequently produced metal oxide film. At 40 min solvent annealing time, hexagonally close packed structures were produced with cylinder diameters ∼40 nm. Subsequently, the BCP films were infiltrated with different metal cations. Metal ions (Cr, Fe, Ni, and Ga) selectively infiltrated the P2VP domain, while the PS did not retain any detectable amount of metal precursor. This gave rise to a metal oxide porous structure after a UV/ozone (UVO) treatment. The results showed that the metal oxide structures demonstrated high fidelity compared to the BCP template and cylindrical domains presented a similar size to the previous PS structure. Moreover, XPS analyses revealed the complete elimination of the BCP template and confirmed the presence of the metal oxides. These metal oxides were used as hard masks for pattern transfer via dry etching as a further application. Silicon nanopores were fabricated mimicking the BCP template and demonstrated a pore depth of ∼50 nm. Ultimately, this strategy can be applied to create different inorganic nanostructures for a diverse range of applications, for example, solar cells, diodes, and integrated circuits. Furthermore, by optimizing the etching parameters, deeper structures can be obtained via ICP/RIE processes, leading to many potential applications.