Household Materials Selection for Homemade Cloth Face Coverings and Their Filtration Efficiency Enhancement with Triboelectric Charging

Design of biodegradable cellulose filtration material with high efficiency and breathability

Using respiratory protective equipment is one of the relevant preventive measures for infectious diseases, including COVID-19, and for various occupational respiratory hazards. Because experienced discomfort may result in a decrease in the utilization of respirators, it is important to enhance the material properties to resolve suboptimal usage. We combined several technologies to produce a filtration material that met requirements set by a cross-disciplinary interview study on the usability of protective equipment. Improved breathability, environmental sustainability, and comfort of the material were achieved by electrospinning poly(ethylene oxide) (PEO) nanofibers on a thin foam-formed fabric from regenerated cellulose fibers. The high filtration efficiency of sub-micron-sized diethylhexyl sebacate (DEHS) aerosol particles resulted from the small mean segment length of 0.35 μm of the nanofiber network. For a particle diameter of 0.6 μm, the filtration efficiency of a single PEO layer varied in the range of 80-97 % depending on the coat weight. The corresponding pressure drop had the level of 20-90 Pa for the airflow velocity of 5.3 cm/s. Using a multilayer structure, a very high filtration efficiency of 99.5 % was obtained with only a slightly higher pressure drop. This opens a route toward designing sustainable personal protective media with improved user experience.

Biodegradable Poly (L-Lactic acid) Fibrous Membrane with Ribbon-Structured Fibers and Ultrafine Nanofibers Enhances Air Filtration Performance

Here, the poly (l-lactic acid) (PLLA) membrane with multi-structured networks (MSN) is successfully prepared by electrospinning technology for the first time. It is composed of micron-sized ribbon-structured fibers and ultrafine nanofibers with a diameter of tens of nanometers, and they are connected to form the new network structure. Thanks to the special fiber morphology and structure, the interception and electrostatic adsorption ability for against atmospheric particulate matter (PM) are significantly enhanced, and the resistance to airflow is reduced due to the "slip effect" caused by ultrafine nanofibers. The PLLA MSN membrane shows excellent filtration performance with ultra-high filtration efficiency (>99.9% for PM2.5 and >99.5% for PM0.3) and ultra-low pressure drop (≈20 Pa). It has demonstrated filtration performance that even exceeds current non-biodegradable polymer materials, laying the foundation for future applications of biodegradable PLLA in the field of air filtration. In addition, this new structure also provides a new idea for optimizing the performance of other polymer materials.

Upgrading Polyolefin Plastic Waste into Multifunctional Porous Graphene using Silicone-Assisted Direct Laser Writing

The widespread use of plastics, especially polyolefin including polyethylene and polypropylene, has led to severe environmental crises. Chemical recycling, a promising solution for extracting value from plastic waste, however, is underutilized due to its complexity. Here, a simple approach, silicone-assisted direct laser writing (SA-DLW) is developed, to upgrade polyolefin plastic waste into multifunctional porous graphene, called laser-induced graphene (LIG). This method involves infiltrating polyolefins with silicone, which retards ablation during the DLW process and supplies additional carbon atoms, as confirmed by experimental and molecular dynamic results. A remarkable conversion yield of 38.3% is achieved. The upgraded LIG exhibited a porous structure and high conductivity, which is utilized for the fabrication of diverse energy and electronic devices with commendable performance. Furthermore, the SA-DLW technique is versatile for upgrading plastic waste in various types and forms. Upgrading plastic waste in the form of fabric has significantly simplified pre-treatment. Finally, a wearable flex sensor is fabricated on the non-woven fabric of a discarded medical mask, which is applied for gesture monitoring. This work offers a simple but effective solution to upgrade plastic waste into valuable products, contributing to the mitigation of environmental challenges posed by plastic pollution.

Versatile Antibacterial and Antioxidant Bacterial Cellulose@Nanoceria Biotextile: Application in Reusable Antimicrobial Face Masks

Despite considerable interest in medical and pharmaceutical fields, there remains a notable absence of functional textiles that concurrently exhibit antibacterial and antioxidant properties. Herein, a new composite fabric constructed using nanostructured bacterial cellulose (BC) covalently-linked with cerium oxide nanoparticles (BC@CeO2NPs) is introduced. The synthesis of CeO2NPs on the BC is performed via a microwave-assisted, in situ chemical deposition technique, resulting in the formation of mixed valence Ce3+/Ce4+ CeO2NPs. This approach ensures the durability of the composite fabric subjected to multiple washing cycles. The Reactive oxygen species (ROS) scavenging activity of CeO2NPs and their rapid and efficient eradication of >99% model microbes, such as Escherichia coli, Pseudomonas aeruginosa and Staphylococcus aureus remain unaltered in the composite. To demonstrate the feasibility of incorporating the fabric in marketable products, antimicrobial face masks are fabricated with filter layers made of BC@CeO2NPs cross-linked with propylene or cotton fibers. These masks exhibit complete inhibition of bacterial growth in the three bacterial strains, improved breathability compared to respirator masks and enhanced filtration efficiency compared to single-use surgical face masks. This study provides valuable insights into the development of functional BC@CeO2NPs biotextiles in which design can be extended to the fabrication of medical dressings and cosmetic products with combined antibiotic, antioxidant and anti-inflammatory activities.

Microscopy of Woven and Nonwoven Face Covering Materials: Implications for Particle Filtration

A suite of natural, synthetic, and mixed synthetic-natural woven fabrics, along with nonwoven filtration layers from a surgical mask and an N95 respirator, was examined using visible light microscopy, scanning electron microscopy, and micro-X-ray computed tomography (µXCT) to determine the fiber diameter distribution, fabric thickness, and the volume of solid space of the fabrics. Nonwoven materials exhibit a positively skewed distribution of fiber diameters with a mean value of ≈3 μm, whereas woven fabrics exhibit a normal distribution of diameters with mean values roughly five times larger (>15 μm). The mean thickness of the N95 filtration material is 1093 μm and is greater than that of the woven fabrics that span from 420 to 650 μm. A new procedure for measuring the thickness of flannel fabrics is proposed that accounts for raised fibers. µXCT allowed for a quantitative nondestructive approach to measure fabric porosity as well as the surface area/volume. Cotton flannel showed the largest mean isotropy of any fabric, though fiber order within the weave is poorly represented in the surface electron images. Surface fabric isotropy and surface area/volume ratios are proposed as useful microstructural quantities to consider for future particle filtration modeling efforts of woven materials.

Self-Sanitization in a Silk Nanofibrous Network for Biodegradable PM0.3 Filters with In Situ Joule Heating

In the contemporary way of life, face masks are crucial in managing disease transmission and battling air pollution. However, two key challenges, self-sanitization and biodegradation of face masks, need immediate attention, prompting the development of innovative solutions for the future. In this study, we present a novel approach that combines controlled acid hydrolysis and mechanical chopping to synthesize a silk nanofibrous network (SNN) seamlessly integrated with a wearable stainless steel mesh, resulting in the fabrication of self-sanitizable face masks. The distinct architecture of face masks showcases remarkable filtration efficiencies of 91.4, 95.4, and 98.3% for PM0.3, PM0.5, and PM1.0, respectively, while maintaining a comfortable level of breathability (ΔP = 92 Pa). Additionally, the face mask shows that a remarkable thermal resistance of 472 °C cm2 W-1 generates heat spontaneously at low voltage, deactivating Escherichia coli bacteria on the SNN, enabling self-sanitization. The SNN exhibited complete disintegration within the environment in just 10 days, highlighting the remarkable biodegradability of the face mask. The unique advantage of self-sanitization and biodegradation in a face mask filter is simultaneously achieved for the first time, which will open avenues to accomplish environmentally benign next-generation face masks.

Effect of Face Masking on Transmission of SARS-CoV-2

The efficacy of face masking for the public is not convincing to prevent the transmission of respiratory tract viruses such as SARS-CoV-2 when the criteria of evidence-based medicine are applied. This finding is mainly explained by the results from randomized-controlled trials (RCTs) when a high prevalence of the infection and a high compliance in mask wearing was assured. Throughout these studies no significant protective effect was observed. Observational studies with surgical masks describe a significant protective effect, but are prone to confounders such as physical distance. Respirators do not provide an additional health benefit compared to surgical or medical masks (RCTs). Community masks can even increase the risk of infection (RCTs). Based on the categories of evidence-based medicine, the efficacy results can best be categorized as conflicting evidence. Many relevant adverse events are described when masks are worn for hours such as dyspnea (12.2-52.8%), headache (3.9-73.4%), pruritus (0.0-60.0%), and skin reactions (0.0-85.0%). Their frequency is often higher with respirators. In future pandemics, masks should only be recommended or mandated for settings in which a clinically relevant health benefit can be expected, defined as the prevention of severe, critical or fatal disease, that clearly outweighs the expectable associated adverse reactions.

Do Surface Charges on Polymeric Filters and Airborne Particles Control the Removal of Nanoscale Aerosols by Polymeric Facial Masks?

The emergence of facial masks as a critical health intervention to prevent the spread of airborne disease and protect from occupational nanomaterial exposure highlights the need for fundamental insights into the interaction of nanoparticles (<200 nm) with modern polymeric mask filter materials. While most research focuses on the filtration efficiency of airborne particles by facial masks based on pore sizes, pressure drop, or humidity, only a few studies focus on the importance of aerosol surface charge versus filter surface charge and their role in the net particle filtration efficiency of mask filters. In this study, experiments were conducted to assess mask filter filtration efficiency using positively and negatively charged polystyrene particles (150 nm) as challenge aerosols at varying humidity levels. Commercial masks with surface potential (Ψf) in the range of -10 V to -800 V were measured by an electrostatic voltmeter and used for testing. Results show that the mask filtration efficiency is highly dependent on the mask surface potential as well as the charge on the challenge aerosol, ranging from 60% to 98%. Eliminating the surface charge results in a maximum 43% decrease in filtration efficiency, emphasizing the importance of electrostatic charge interactions during the particle capture process. Moreover, increased humidity can decrease the surface charge on filters, thereby decreasing the mask filtration efficiency. The knowledge gained from this study provides insight into the critical role of electrostatic attraction in nanoparticle capture mechanisms and benefits future occupational and environmental health studies.

Water-blocking Asphyxia of N95 Medical Respirator During Hot Environment Work Tasks With Whole-body Enclosed Anti-bioaerosol Suit

Background

During hot environment work tasks with whole-body enclosed anti-bioaerosol suit, the combined effect of heavy sweating and exhaled hot humid air may cause the N95 medical respirator to saturate with water/sweat (i.e., water-blocking).

Methods

32 young male subjects with different body mass indexes (BMI) in whole-body protection (N95 medical respirator + one-piece protective suit + head covering + protective face screen + gloves + shoe covers) were asked to simulate waste collecting from each isolated room in a seven-story building at 27-28°C, and the weight, inhalation resistance (Rf), and aerosol penetration of the respirator before worn and after water-blocking were analyzed.

Results

All subjects reported water-blocking asphyxia of the N95 respirators within 36-67 min of the task. When water-blocking occurred, the Rf and 10-200 nm total aerosol penetration (Pt) of the respirators reached up to 1270-1810 Pa and 17.3-23.3%, respectively, which were 10 and 8 times of that before wearing. The most penetration particle size of the respirators increased from 49-65 nm before worn to 115-154 nm under water-blocking condition, and the corresponding maximum size-dependent aerosol penetration increased from 2.5-3.5% to 20-27%. With the increase of BMI, the water-blocking occurrence time firstly increased then reduced, while the Rf, Pt, and absorbed water all increased significantly.

Conclusions

This study reveals respirator water-blocking and its serious negative impacts on respiratory protection. When performing moderate-to-high-load tasks with whole-body protection in a hot environment, it is recommended that respirator be replaced with a new one at least every hour to avoid water-blocking asphyxia.

Importance of Dipole Orientation in Electrostatic Aerosol Filtration

Electrostatic charge is a major part of modern-day aerosol filtration media (e.g., N95 respirators and surgical facemasks) that has remained poorly understood due to its complicated physics. As such, charging a fibrous material has relied on empiricism in dire need of a mathematical foundation to further advance product design and optimization. In this concern, we have conducted a series of numerical simulations to improve our understanding of how an electrostatically charged fiber captures airborne particles and to quantify how the fiber's dipole orientation impacts its capture efficiency. Special attention was paid to the role of Coulomb and dielectrophoretic forces in the capture of particles of different charge polarities (e.g., particles having a Boltzmann charge distribution). Simulation results were compared with the predictions of the popular empirical correlations from the literature and discussed in detail. Predictions of the empirical correlations better agreed with the simulation results obtained for fibers with a dipole perpendicular to the flow direction rather than for fibers with a dipole parallel to the flow. This indicates that such empirical correlations are more suitable for filters charged via contact electrification (friction charging), where the dipoles are mostly perpendicular to the flow direction, and less suitable for corona-charged media, where the fiber dipoles are generally parallel to the flow direction.

Single-Layer and Double-Layer Filtration Materials Based on Polyvinylidene Fluoride-Co-hexafluoropropylene Nanofibers Coated on Melamine Microfibers

In this work, we demonstrate selected optimization changes in the simple design of filtration masks to increase particle removal efficiency (PRE) and filter quality factor by combining experiments and numerical modeling. In particular, we focus on single-layer filters fabricated from uniform thickness fibers and double-layer filters consisting of a layer of highly permeable thick fibers as a support and a thin layer of filtering electrospun nanofibers. For single-layer filters, we demonstrate performance improvement in terms of the quality factor by optimizing the geometry of the composition. We show significantly better PRE performance for filters composed of micrometer-sized fibers covered by a thin layer of electrospun nanofibers. This work is motivated and carried out in collaboration with a targeted industrial development of selected melamine-based filter nano- and micromaterials.

Attaching protein-adsorbing silica particles to the surface of cotton substrates for bioaerosol capture including SARS-CoV-2

The novel coronavirus pandemic (COVID-19) has necessitated a global increase in the use of face masks to limit the airborne spread of the virus. The global demand for personal protective equipment has at times led to shortages of face masks for the public, therefore makeshift masks have become commonplace. The severe acute respiratory syndrome caused by coronavirus-2 (SARS-CoV-2) has a spherical particle size of ~97 nm. However, the airborne transmission of this virus requires the expulsion of droplets, typically ~0.6-500 µm in diameter (by coughing, sneezing, breathing, and talking). In this paper, we propose a face covering that has been designed to effectively capture SARS-CoV-2 whilst providing uncompromised comfort and breathability for the wearer. Herein, we describe a material approach that uses amorphous silica microspheres attached to cotton fibres to capture bioaerosols, including SARS CoV-2. This has been demonstrated for the capture of aerosolised proteins (cytochrome c, myoglobin, ubiquitin, bovine serum albumin) and aerosolised inactivated SARS CoV-2, showing average filtration efficiencies of ~93% with minimal impact on breathability.

Electrospun Nanocomposite Fibrous Membranes for Sustainable Face Mask Based on Triboelectric Nanogenerator with High Air Filtration Efficiency

Abstract

Air pollution caused by the rapid development of industry has always been a great issue to the environment and human being's health. However, the efficient and persistent filtration to PM0.3 remains a great challenge. Herein, a self-powered filter with micro-nano composite structure composed of polybutanediol succinate (PBS) nanofiber membrane and polyacrylonitrile (PAN) nanofiber/polystyrene (PS) microfiber hybrid mats was prepared by electrospinning. The balance between pressure drop and filtration efficiency was achieved through the combination of PAN and PS. In addition, an arched TENG structure was created using the PAN nanofiber/PS microfiber composite mat and PBS fiber membrane. Driven by respiration, the two fiber membranes with large difference in electronegativity achieved contact friction charging cycles. The open-circuit voltage of the triboelectric nanogenerator (TENG) can reach to about 8 V, and thus the high filtration efficiency for particles was achieved by the electrostatic capturing. After contact charging, the filtration efficiency of the fiber membrane for PM0.3 can reach more than 98% in harsh environments with a PM2.5 mass concentration of 23,000 µg/m3, and the pressure drop is about 50 Pa, which doesn't affect people's normal breathing. Meanwhile, the TENG can realize self-powered supply by continuously contacting and separating the fiber membrane driven by respiration, which can ensure the long-term stability of filtration efficiency. The filter mask can maintain a high filtration efficiency (99.4%) of PM0.3 for 48 consecutive hours in daily environments.

Graphical abstract

Supplementary Information

The online version contains supplementary material available at 10.1007/s42765-023-00299-z.

A novel investigations on medical and non-medical mask performance with influence of marine waste microplastics (polypropylene)

The entire human race is struggling with the spread of COVID-19. Worldwide, the wearing of face masks is indispensable to prevent such spread. Despite numerous studies reporting on the fabrication of face masks and surgical masks to reduce spread and thus human deaths, this novel work is considered the marine waste of microplastics, namely Polypropylene (PP) polymer, used to fabricate non-woven fabric masks through the melt-blown process. This experimental work aims to maximize the mask's quality and minimize its fabrication cost by optimizing the melt-blown process parameters and using microplastics. The melt-blown process was used to make masks. Parameters such as extruder temperature, hot air temperature, melt flow rate, and die-to-collector distance (DCD) were investigated as independent variables. The quality of the mask was investigated in terms of bacterial filtration efficiency (BFE), particle filtration efficiency (PFE), and differential pressure. The Taguchi L16 orthogonal array and Taguchi analysis were employed for experimental design and statistical optimization, respectively. The results reveal that the higher BFE and PFE are recorded at 96.7 % and 98.6 %, respectively. The surface morphological investigation on different layers ensured the fine and uniform porosity of the layers and exhibited minimum breath resistance (a low differential pressure of 0.00152 kPa/cm²). Hence the chemically treated marine waste microplastics improved the masks' performance.

Surface-Functionalized Metal-Organic Frameworks for Binding Coronavirus Proteins

Since the outbreak of SARS-CoV-2, a multitude of strategies have been explored for the means of protection and shielding against virus particles: filtration equipment (PPE) has been widely used in daily life. In this work, we explore another approach in the form of deactivating coronavirus particles through selective binding onto the surface of metal-organic frameworks (MOFs) to further the fight against the transmission of respiratory viruses. MOFs are attractive materials in this regard, as their rich pore and surface chemistry can easily be modified on demand. The surfaces of three MOFs, UiO-66(Zr), UiO-66-NH2(Zr), and UiO-66-NO2(Zr), have been functionalized with repurposed antiviral agents, namely, folic acid, nystatin, and tenofovir, to enable specific interactions with the external spike protein of the SARS virus. Protein binding studies revealed that this surface modification significantly improved the binding affinity toward glycosylated and non-glycosylated proteins for all three MOFs. Additionally, the pores for the surface-functionalized MOFs can adsorb water, making them suitable for locally dehydrating microbial aerosols. Our findings highlight the immense potential of MOFs in deactivating respiratory coronaviruses to be better equipped to fight future pandemics.

Functional Textile Materials for Blocking COVID-19 Transmission

The outbreak of COVID-19 provided a warning sign for society worldwide: that is, we urgently need to explore effective strategies for combating unpredictable viral pandemics. Protective textiles such as surgery masks have played an important role in the mitigation of the COVID-19 pandemic, while revealing serious challenges in terms of supply, cross-infection risk, and environmental pollution. In this context, textiles with an antivirus functionality have attracted increasing attention, and many innovative proposals with exciting commercial possibilities have been reported over the past three years. In this review, we illustrate the progress of textile filtration for pandemics and summarize the recent development of antiviral textiles for personal protective purposes by cataloging them into three classes: metal-based, carbon-based, and polymer-based materials. We focused on the preparation routes of emerging antiviral textiles, providing a forward-looking perspective on their opportunities and challenges, to evaluate their efficacy, scale up their manufacturing processes, and expand their high-volume applications. Based on this review, we conclude that ideal antiviral textiles are characterized by a high filtration efficiency, reliable antiviral effect, long storage life, and recyclability. The expected manufacturing processes should be economically feasible, scalable, and quickly responsive.

Effectiveness of Inexpensive Cloth Facemasks and Their Amendments to Reduce Ambient Particulate Exposures: A Case of Kathmandu, Nepal

Inexpensive cloth masks are widely used to reduce particulate exposures, but their use became ubiquitous after the outbreak of COVID-19. A custom experimental setup (semiactive at 5.1 m/s airflow rate) was fabricated to examine the efficiency of different types of commercial facemasks collected randomly from street vendors. The sample (N = 27) including (n = 16) cloth masks (CMs), (n = 7) surgical masks (SMs), and (n = 4) N95 filtering facepiece respirators (FFRs), of which SMs and N95 FFRs taken as a standard for efficiency comparison were all tested against ambient aerosols (PM_2.5 and PM₁₀ μg/m³). The prototype cloth masks (PTCMs) (N = 5) design was tailored, and their performance was assessed and compared with that of standard commercial masks. The filtering efficiency tested against ambient coarse particulates (PM₁₀) ranged from (5% to 34%) for CMs with an average of 16%, (37% to 46%) for SMs with an average of 42%, (59% to 72%) for PTCMs with an average of 65%, and (70% to 75%) for N95 FFRs with an average of 71%, whereas against fine particulates (PM_2.5), efficacy ranged from (4% to 29%) for CMs with an average of 13%, (34% to 44%) for SMs with an average of 39%, (53% to 68%) for PTCMs with an average of 60%, and (68% to 73%) for N95 FFRs with an average of 70%, respectively. The efficiency followed the order N95 FFRs > PTCMs > SMs > CMs showing poor exposure reduction potential in CMs and high exposure reduction potential in N95 FFRs and PTCMs. Amendment in existing CMs using eco-friendly cotton fabric with better facial adherence can protect human health from exposure to fine particulates <2.5 μm and can reduce the risk of micro-plastic pollution caused by polypropylene (PP) facemasks.

A computational framework for transmission risk assessment of aerosolized particles in classrooms

Infectious airborne diseases like the recent COVID-19 pandemic render confined spaces high-risk areas. However, in-person activities like teaching in classroom settings and government services are often expected to continue or restart quickly. It becomes important to evaluate the risk of airborne disease transmission while accounting for the physical presence of humans, furniture, and electronic equipment, as well as ventilation. Here, we present a computational framework and study based on detailed flow physics simulations that allow straightforward evaluation of various seating and operating scenarios to identify risk factors and assess the effectiveness of various mitigation strategies. These scenarios include seating arrangement changes, presence/absence of computer screens, ventilation rate changes, and presence/absence of mask-wearing. This approach democratizes risk assessment by automating a key bottleneck in simulation-based analysis-creating an adequately refined mesh around multiple complex geometries. Not surprisingly, we find that wearing masks (with at least 74% inward protection efficiency) significantly reduced transmission risk against unmasked and infected individuals. While the use of face masks is known to reduce the risk of transmission, we perform a systematic computational study of the transmission risk due to variations in room occupancy, seating layout and air change rates. In addition, our findings on the efficacy of face masks further support use of face masks. The availability of such an analysis approach will allow education administrators, government officials (courthouses, police stations), and hospital administrators to make informed decisions on seating arrangements and operating procedures.

Supplementary Information

The online version contains supplementary material available at 10.1007/s00366-022-01773-9.

A Review of Filtration Performance of Protective Masks

Masks are essential and effective small protective devices used to protect the general public against infections such as COVID-19. However, available systematic reviews and summaries on the filtration performance of masks are lacking. Therefore, in order to investigate the filtration performance of masks, filtration mechanisms, mask characteristics, and the relationships between influencing factors and protective performance were first analyzed through mask evaluations. The summary of filtration mechanisms and mask characteristics provides readers with a clear and easy-to-understand theoretical cognition. Then, a detailed analysis of influencing factors and the relationships between the influencing factors and filtration performance is presented in. The influence of the aerosol size and type on filtration performance is nonlinear and nonconstant, and filtration efficiency decreases with an increase in the gas flow rate; moreover, fitness plays a decisive role in the protective effects of masks. It is recommended that the public should wear surgical masks to prevent COVID-19 infection in low-risk and non-densely populated areas. Future research should focus on fitness tests, and the formulation of standards should also be accelerated. This paper provides a systematic review that will be helpful for the design of masks and public health in the future.

Evaluation of Mask Performances in Filtration and Comfort in Fabric Combinations

A systemic study on improving particulate pollutant filtration efficiency through the combination of conventional fabrics is presented with the objective of finding comfortable, yet effective airway mask materials and products. Fabrics, nonwovens, and their combinations made of cotton, silk, wool, and synthetic fibers are examined on their filtration efficiency for aerosol particles with diameters ranging from 0.225 μm to 3.750 μm under industry-standard testing conditions. It is found that composite fabrics can improve filtration efficiency more than just layers of the same fabric, and the filtration quality factor of some of the fabric combinations can exceed that of the standard melt-blown materials. In addition, fabric friction and charging between the combined layers also improve filtration efficiency substantially. With a broader understanding of the fabric characteristics, we may design mask products with reduced facial skin discomfort, better aesthetics, as well as the ability to alleviate the environmental impact of discarded protective masks in the extended period of controlling the transmission of pollutants and viruses, such as during the COVID-19 pandemic.

Self-charging electrostatic face masks leveraging triboelectrification for prolonged air filtration

Electrostatic adsorption is an important complement to the mechanical filtration for high-efficiency air filtering. However, the electrostatic charge decays with time, especially in humid conditions. In this work, a self-charging air filter is presented to capture airborne particles in an efficient and long-lasting manner without the need of external power sources. Leveraging the triboelectric effect between the electrospun poly(vinylidene fluoride) nanofiber film and nylon fabric, the self-charging air filter-based mask excited by breathing can continuously replenish electrostatic charges. As a result, its effective lifespan is up to 60 hours (including 30 hours of wearing), with a minimum filtration efficiency of 95.8% for 0.3-μm particles. The filtration efficiency and lifespan are significantly higher than those of a commercial surgical mask. Furthermore, we uncover the quantitative relation between filtration efficiency and surface electrostatic potential. This work provides an effective strategy to significantly prolong the electrostatic adsorption efficacy for high-performance air-filtering masks.

Constructing Janus Microsphere Membranes for Particulate Matter Filtration, Directional Water Vapor Transfer, and High-Efficiency Broad-Spectrum Sterilization

Commercial masks have significant drawbacks, including low water vapor transmission efficiency and limited ability to inhibit harmful microorganisms, whereas in this contribution, a series of Janus microsphere membranes are developed with hierarchical structures by quenching and crystallizing 12-hydroxystearic acid and halicin layer-by-layer on a polypropylene non-woven fabric, laminating them with hydrophilic cotton fibers in a one-pot process, and further demonstrate the potential of this composite system as masks. Through further optimization, excellent superhydrophobic/superhydrophilic properties (contact angle 157.1°/0°), superior filtering effects (93.54% for PM_2.5 and 98.35% for PM₁₀ ), with a low-filtration resistance (57 Pa) and a quality factor of up to 0.072 Pa^-1 are achieved, all better than that of commercial N95 masks. In addition, the membrane allows for the directional transport of water vapor from the inside out, increasing the water vapor transmission rate by more than 20% compared with the monolayer hydrophobic microsphere membrane. It also has a bactericidal capacity of over 99.9999% against Escherichia coli and is tested for robustness and stability in various extreme environments. This work may shed light on designing novel filter media with versatile functions, meanwhile, the materials can also be used in protective equipment against the new coronavirus.

A review on the effectiveness of various masks in protection against COVID-19

As of June1st 2021, more than 17 crore people have been infected with COVID-19 across the globe, and almost 3 crore people have been infected in India. The virus can spread through even normal actions like talking with particle emission rates inversely correlating with word frequency and volume, which can be reduced by covering the mouth. However, there is debate concerning the effectiveness of the various face mask types in preventing respiratory infections. Many have reported that wearing a mask is uncomfortable, especially when worn for long hours and while performing strenuous activities. Another disease that has raised its head is mucormycosis. However, COVID-19 can be a serious infection in many, with many fatalities. It is not yet clear how much protection vaccines give, and in a hugely populated country like India, it may be very difficult to vaccinate the whole population. Moreover, the vaccination for pediatric groups has just started. So, it is imperative to wear masks that can be protective against infection. However, some people believe that a straightforward cotton mask is insufficient. We set out to analyze the efficacy of masks through this investigation. According to the results of this systematic review, there are no studies that give conclusive evidence that using face masks as recommended by current public health guidelines will stop this condition. This is a significant discovery that should be communicated to the scientific community and calls into question the rationale for inconsistent and differing public health recommendations.

Biocompatible curcumin coupled nanofibrous membrane for pathogens sterilization and isolation

Airborne transmission of pathogens is the most probable cause for the spread of respiratory diseases, which can be intercepted by personal protective equipment such as masks. In this study, an efficient antiviral personal protective filter was fabricated by coupling the biocompatible curcumin (CCM) with nanofibrous polytetrafluoroethylene (PTFE) membrane. The CCM extracted from plants was first dissolved in acidified ethanol at a certain pH and temperature to optimize its loading concentration, antiviral activation, and binding forces on the polyethylene terephthalate (PET) support to form a pre-filtration layer at the front section of the filter. Ultrathin PTFE membrane was then fabricated on the antibacterial-antiviral PET support (A-A PET) by controllable heating lamination. This functional layer of the filter exhibits good gas permeance (3423.6 m³/(m²·h·kPa)) and ultrafine particles rejection rate (>98.79%). Moreover, the obtained A-A filter exhibit a high antibacterial rate against a variety of bacteria (E. coli, B. subtilis, A. niger, and Penicillium were 99.84%, 99.02%, 93.60%, 95.23%, respectively). Forthwith virucidal (SARS-CoV-2) efficiency of the A-A filter can reach 99.90% for 5 min. The filter shows good stability after 10 heating cycles, demonstrating its reusability.

Comparison of measurement systems for assessing number- and mass-based particle filtration efficiency

The particle filtration efficiency (PFE) of a respirator or face mask is one of its key properties. While the physics of particle filtration results in the PFE being size-dependent, measurement standards are specified using a single, integrated PFE, for simplicity. This integrated PFE is commonly defined concerning either the number (NPFE) or mass (MPFE) distribution of particles as a function of size. This relationship is non-trivial; it is influenced by both the shape of the particle distribution and the fact that multiple practical definitions of particle size are used. This manuscript discusses the relationship between NPFE and MPFE in detail, providing a guide to practitioners. Our discussion begins with a description of the theory underlying different variants of PFE. We then present experimental results for a database of size-resolved PFE (SPFE) measurements for several thousand candidate respirators and filter media, including filter media with systematically varied properties and commercial samples that span 20%-99.8% MPFE. The observed relationships between NPFE and MPFE are discussed in terms of the most-penetrating particle size (MPPS) and charge state of the media. For the sodium chloride particles used here, we observed that the MPFE was greater than NPFE for charged materials and vice versa for uncharged materials. This relationship is observed because a shift from NPFE to MPFE weights the distribution toward larger sizes, while charged materials shift the MPPS to smaller sizes. Results are validated by comparing the output of a pair of automated filter testers, which are used in gauging standards compliance, to that of MPFE computed from a system capable of measuring SPFE over the 20 nm-500 nm range.

Impact of washing parameters on bacterial filtration efficiency and breathability of community and medical facemasks

Can medical face masks be replaced by reusable community face masks with similar performance? The influence of the number of wash cycles, the wash temperature and the use of detergent was evaluated on the performance of one medical face masks (MFM) and ten community face masks (CFM). The performance of the new and washed masks was characterized from the bacterial filtration efficiency (BFE) and the differential pressure (DP). The tests on the new masks showed that the MFM had always better BFE than CFMs. Although two of the CFMs showed a BFE value exceeding 95%, only one can be classified as type I MFM based on both BFE and DP requirements. The influence of the washing parameters was investigated on the MFM and these two CMFs with excellent BFE properties. The parameters had no effect on the BFE of CFMs whilst the MFM exhibited a loss in efficiency when washed with detergent. The DP of masks were not impacted by the washing. The results clearly show that even though a compromise has to be made between the BFE and breathability, it seems possible to manufacture CFMs with performances similar to a type I MFM, without achieving type II requirements.

Saving 80% Polypropylene in Facemasks by Laser-Assisted Melt-Blown Nanofibers

The ongoing coronavirus (COVID-19) pandemic requires enormous production of facemasks and related personal protection materials, thereby increasing the amount of nondegradable plastic waste. The core material for facemasks is melt-blown polypropylene (PP) fiber. Each disposable facemask consumes ∼0.7 g of PP fibers, resulting in annual global consumption and disposal of more than 1 150 000 tons of PP fibers annually. Herein, we developed a laser-assisted melt-blown (LAMB) technique to manufacture PP nanofibers with a quality factor of 0.17 Pa^-1 and significantly reduced the filter's weight. We demonstrated that a standard surgical facemask could be made with only 0.13 g of PP nanofibers, saving approximately 80% of the PP materials used in commercial facemasks. Theoretical analysis and modeling were also conducted to understand the LAMB process. Importantly, nanofibers can be easily scaled up for mass production by upgrading traditional melt blown line with scanning laser-assisted melt-blown (SLAMB).

Crowdsourcing homemade facemasks: 772 U.S. health facilities' responses to personal protective equipment shortages in the first half of 2020

Purpose

We examined 772 U.S. health facilities' responses to Personal Protective Equipment (PPE) shortages in the first half of 2020, as they crowdsourced face coverings from volunteer makers to be used as respiratory protection during crisis surge capacity. The purpose was to examine facemask specification requests from health facilities and develop a framework for crowdsourcing last resort PPE.

Design/methodology/approach

Homemade facemask donation requests from health facilities in 47 states systematically recorded in a public database maintained by public health graduate students at a major U.S. university were analysed. Open coding was used to content analyse facemask types and specifications, intended uses, delivery logistics and donation management strategies.

Findings

Our analysis revealed information gaps: Science‐based information was scarce in 2020, leading to improvised specifications for facemask materials and designs. It also revealed the emergence of a crowdsourcing structure: Task specifications for volunteer facemasks makers, delivery logistics, and practical management of donations within the pandemic context. In anticipation of future pandemics and localised PPE shortages, we build on this empirical evidence to propose a framework for crowdsourcing science‐informed facemasks from volunteers. Categorised within (a) logistics and workflow management, (b) task specifications and management, and (c) practical management of contributions functional areas, the framework outlines the required tasks and specifications for crowdsourcing.

Originality

A novel empirically derived framework for crowdsourcing homemade facemasks is proposed, based on empirical analysis and crowdsourcing system design strategies. Our findings and the framework may be used for refining crisis capacity guidelines, as part of strategic planning and preparation for future pandemics that disrupt supply chains and cause shortages in protective equipment.

At least 772 health facilities in 47 U.S. states experienced Personal Protective Equipment (PPE) shortages in 2020.

During crisis surge capacity, they crowdsourced homemade masks from volunteers.

The database shows information gaps and an emerging crowdsourcing structure.

A crowdsourcing framework is essential for effective sourcing of homemade face coverings from volunteer makers during pandemics and surge capacity.

One year of surgical mask testing at the University of Bologna labs: Lessons learned from data analysis

The outbreak of SARS-CoV-2 pandemic highlighted the worldwide lack of surgical masks and personal protective equipment, which represent the main defense available against respiratory diseases as COVID-19. At the time, masks shortage was dramatic in Italy, the first European country seriously hit by the pandemic: aiming to address the emergency and to support the Italian industrial reconversion to the production of surgical masks, a multidisciplinary team of the University of Bologna organized a laboratory to test surgical masks according to European regulations. The group, driven by the expertise of chemical engineers, microbiologists, and occupational physicians, set-up the test lines to perform all the functional tests required. The laboratory started its activity on late March 2020, and as of the end of December of the same year 435 surgical mask prototypes were tested, with only 42 masks compliant to the European standard. From the analysis of the materials used, as well as of the production methods, it was found that a compliant surgical mask is most likely composed of three layers, a central meltblown filtration layer and two external spunbond comfort layers. An increase in the material thickness (grammage), or in the number of layers, does not improve the filtration efficiency, but leads to poor breathability, indicating that filtration depends not only on pure size exclusion, but other mechanisms are taking place (driven by electrostatic charge). The study critically reviewed the European standard procedures, identifying the weak aspects; among the others, the control of aerosol droplet size during the bacterial filtration test results to be crucial, since it can change the classification of a mask when its performance lies near to the limiting values of 95 or 98%.

Commercial Janus Fabrics as Reusable Facemask Materials: A Balance of Water Repellency, Filtration Efficiency, Breathability, and Reusability

Facemasks as personal protective equipment play a significant role in helping prevent the spread of viruses during the COVID-19 pandemic. A desired reusable fabric facemask should strike a balance of water repellency, good filtration efficiency (FE), breathability, and mechanical robustness against washing cycles. Despite significant efforts in testing various commercial fabric materials for filtration efficiency, few have investigated fabric performance as a function of the fiber/yarn morphology and wettability of the fabric itself. In this study, we examine commercial fabrics with Janus-like behaviors to determine the best reusable fabric facemask materials by understanding the roles of morphology, porosity, and wettability of the fabric on its overall performance. We find that the outer layer of the diaper fabric consisted of laminated polyurethane, which is hydrophobic, has low porosity (∼5%) and tightly woven yarn structures, and shows the highest overall FE (up to 54%) in the submicron particle size range (0.03-0.6 μm) among the fabrics tested. Fabric layers with higher porosity lead to lower-pressure drops, indicating higher breathability but lower FE. Tightly woven waterproof rainwear fabrics perform the best after 10 washing cycles, remaining intact morphologically with only a 2-5% drop in the overall FE in the submicron particle size range, whereas other knitted fabric layers become loosened and the laminated polyurethane thin film on the diaper fabric is wrinkled. In comparison, the surgical masks and N95 respirators made from nonwoven polypropylene (PP) fibers see over a 30% decline in the overall FE after 10 washing cycles. Overall, we find that tightly woven Janus fabrics consisting of a low porosity, a hydrophobic outer layer, and a high porosity and hydrophilic inner layer offer the best performance among the fabrics tested as they can generate a high overall FE, achieve good breathability, and maintain fabric morphology and performance over multiple washing cycles.

Disadvantage of the FDM method for printing protective masks against COVID-19 and solution

Outages in the supply of basic medical supplies and protective equipment have led to efforts to replace them. The team of BUT employees and students has developed a protective half mask that can also be printed on a standard 3D printer without the use of special materials. The original half mask is intended as an improvised protection that can be easily printed on standard 3D printers with FDM technology. Problematic possibilities of sealing the entire surface of the print due to its porosity were solved with the help of a nitrile examination glove. Commonly available equipment is enough to produce this half mask.

The emission and dynamics of droplets from human expiratory activities and COVID-19 transmission in public transport system: A review

The public transport system, containing a large number of passengers in enclosed and confined spaces, provides suitable conditions for the spread of respiratory diseases. Understanding how diseases are transmitted in public transport environment is of vital importance to public health. However, this is a highly multidisciplinary matter and the related physical processes including the emissions of respiratory droplets, the droplet dynamics and transport pathways, and subsequently, the infection risk in public transport, are poorly understood. To better grasp the complex processes involved, a synthesis of current knowledge is required. Therefore, we conducted a review on the behaviors of respiratory droplets in public transport system, covering a wide scope from the emission profiles of expiratory droplets, the droplet dynamics and transport, to the transmission of COVID-19 in public transport. The literature was searched using related keywords in Web of Science and PubMed and screened for suitability. The droplet size is a key parameter in determining the deposition and evaporation, which together with the exhaled air velocity largely determines the horizontal travel distance. The potential transmission route and transmission rate in public transport as well as the factors influencing the virus-laden droplet behaviors and virus viability (such as ventilation system, wearing personal protective equipment, air temperature and relative humidity) were also discussed. The review also suggests that future studies should address the uncertainties in droplet emission profiles associated with the measurement techniques, and preferably build a database based on a unified testing protocol. Further investigations based on field measurements and modeling studies into the influence of different ventilation systems on the transmission rate in public transport are also needed, which would provide scientific basis for controlling the transmission of diseases.

High-quality and easy-to-regenerate personal filter

Proper respiratory tract protection is the key factor to limiting the rate of COVID-19 spread and providing a safe environment for health care workers. Traditional N95 (FFP2) respirators are not easy to regenerate and thus create certain financial and ecological burdens; moreover, their quality may vary significantly. A solution that would overcome these disadvantages is desirable. In this study a commercially available knit polyester fleece fabric was selected as the filter material, and a total of 25 filters of different areas and thicknesses were prepared. Then, the size-resolved filtration efficiency (40–400 nm) and pressure drop were evaluated at a volumetric flow rate of 95 L/min. We showed the excellent synergistic effect of expanding the filtration area and increasing the number of filtering layers on the filtration efficiency; a filter cartridge with 8 layers of knit polyester fabric with a surface area of 900 cm² and sized 25 × 14 × 8 cm achieved filtration efficiencies of 98% at 95 L/min and 99.5% at 30 L/min. The assembled filter kit consists of a filter cartridge (14 Pa) carried in a small backpack connected to a half mask with a total pressure drop of 84 Pa at 95 L/min. In addition, it is reusable, and the filter material can be regenerated at least ten times by simple methods, such as boiling. We have demonstrated a novel approach for creating high-quality and easy-to-breathe-through respiratory protective equipment that reduces operating costs and is a green solution because it is easy to regenerate.

Face masks to fight against COVID-19 pandemics: A comprehensive review of materials, design, technology and product development

The outbreak of COVID-19 has created renewed attention on research and large scale manufacturing of face masks. In the last two decades, usage of face masks for respiratory protection has gained increased importance as a measure to control the maladies and fatalities due to exposure to particulate pollutants and toxic pathogens. Numerous variants of surgical and high-performance respirator masks are available in the market, and yet the fibrous materials science researchers, manufacturers and public health agencies are making concerted efforts towards improvising them with respect to self-sterilisability, facial fit, thermo-physiological comfort, reusability and biodegradability, while maintaining or rather enhancing the filtration efficiency. This review article presents a compendium of materials, design and performance standards of existing face masks, as well as elaborates on developments made for their performance enhancement. The criticality of inculcation of good hygiene habits and earnest compliance to correct mask donning and doffing practices has also been highlighted. This review is expected to make valuable contributions in the present COVID-19 scenario when donning a face mask has become mandatory.

Do They Really Work? Quantifying Fabric Mask Effectiveness to Improve Public Health Messaging

The purpose of this study is to compare masks (non-medical/fabric, surgical, and N95 respirators) on filtration efficiency, differential pressure, and leakage with the goal of providing evidence to improve public health messaging. Masks were tested on an anthropometric face filtration mount, comparing both sealed and unsealed. Overall, surgical and N95 respirators provided significantly higher filtration efficiency (FE) and differential pressure (dP). Leakage comparisons are one of the most significant factors in mask efficiency. Higher weight and thicker fabric masks had significantly higher filtration efficiency. The findings of this study have important implications for communication and education regarding the use of masks to prevent the spread of COVID-19 and other respiratory illnesses, specifically the differences between sealed and unsealed masks. The type and fabric of facial masks and whether a mask is sealed or unsealed has a significant impact on the effectiveness of a mask. Findings related to differences between sealed and unsealed masks are of critical importance for health care workers. If a mask is not completely sealed around the edges of the wearer, FE for this personal protective equipment is misrepresented and may create a false sense of security. These results can inform efforts to educate health care workers and the public on the importance of proper mask fit.

Low cost centrifugal melt spinning for distributed manufacturing of non-woven media

Centralized manufacturing and global supply chains have emerged as an efficient strategy for large-scale production of goods throughout the 20th century. However, while this system of production is highly efficient, it is not resilient. The COVID-19 pandemic has seen numerous supply chains fail to adapt to sudden changes in supply and demand, including those for goods critical to the pandemic response such as personal protective equipment. Here, we consider the production of the non-woven polypropylene filtration media used in face filtering respirators (FFRs). The FFR supply chain's reliance on non-woven media sourced from large, centralized manufacturing facilities led to a supply chain failure. In this study, we present an alternative manufacturing strategy that allows us to move towards a more distributed manufacturing practice that is both scalable and robust. Specifically, we demonstrate that a fiber production technique known as centrifugal melt spinning can be implemented with modified, commercially-available cotton candy machines to produce nano- and microscale non-woven fibers. We evaluate several post processing strategies to transform the produced material into viable filtration media and then characterize these materials by measuring filtration efficiency and breathability, comparing them against equivalent materials used in commercially-available FFRs. Additionally, we demonstrate that waste plastic can be processed with this technique, enabling the development of distributed recycling strategies to address the growing plastic waste crisis. Since this method can be employed at small scales, it allows for the development of an adaptable and rapidly deployable distributed manufacturing network for non-woven materials that is financially accessible to more people than is currently possible.

Face Masks to Combat Coronavirus (COVID-19)-Processing, Roles, Requirements, Efficacy, Risk and Sustainability

Increasingly prevalent respiratory infectious diseases (e.g., COVID-19) have posed severe threats to public health. Viruses including coronavirus, influenza, and so on can cause respiratory infections. A pandemic may potentially emerge owing to the worldwide spread of the virus through persistent human-to-human transmission. However, transmission pathways may vary; respiratory droplets or airborne virus-carrying particles can have a key role in transmitting infections to humans. In conjunction with social distancing, hand cleanliness, and other preventative measures, the use of face masks is considered to be another scientific approach to combat ubiquitous coronavirus. Different types of face masks are produced using a range of materials (e.g., polypropylene, polyacrylonitrile, polycarbonate, polyurethane, polystyrene, polyester and polyethylene) and manufacturing techniques (woven, knitted, and non-woven) that provide different levels of protection to the users. However, the efficacy and proper disposal/management of the used face masks, particularly the ones made of non-biodegradable polymers, pose great environmental concerns. This review compiles the recent advancements of face masks, covering their requirements, materials and techniques used, efficacy, challenges, risks, and sustainability towards further enhancement of the quality and performance of face masks.

Fitted filtration efficiency and breathability of 2-ply cotton masks: Identification of cotton consumer categories acceptable for home-made cloth mask construction

The objective of this study was to characterize commercially-available cotton fabrics to determine their suitability as materials for construction of cloth masks for personal and public use to reduce infectious disease spread. The study focused on cottons because of their widespread availability, moderate performance and they are recommended for inclusion in home-made masks by international health authorities. Fifty-two cottons were analyzed by electron microscopy to determine fabric characteristics and fabric weights. Sixteen fabrics were selected to test for breathability and to construct 2-ply cotton masks of a standard design to use in quantitative fit testing on a human participant. Cotton mask fitted filtration efficiencies (FFEs) for 0.02-1 μm ambient and aerosolized sodium chloride particles ranged from 40 to 66% compared with the mean medical mask FFE of 55±2%. Pressure differentials across 2-ply materials ranged from 0.57 to > 12 mm H2O/cm2 on samples of equal surface area with 6 of 16 materials exceeding the recommended medical mask limit. Models were calibrated to predict 2-ply cotton mask FFEs and differential pressures for each fabric based on pore characteristics and fabric weight. Models indicated cotton fabrics from 6 of 9 consumer categories can produce cloth masks with adequate breathability and FFEs equivalent to a medical mask: T-shirt, fashion fabric, mass-market quilting cotton, home décor fabric, bed sheets and high-quality quilting cotton. Masks from one cloth mask and the medical mask were re-tested with a mask fitter to distinguish filtration from leakage. The fabric and medical masks had 3.7% and 41.8% leakage, respectively. These results indicate a well fitted 2-ply cotton mask with overhead ties can perform similarly to a disposable 3-ply medical mask on ear loops due primarily to the superior fit of the cloth mask which compensates for its lower material filtration efficiency.

BIBLIOMETRIC ANALYSIS: NANOTECHNOLOGY AND COVID-19

BACKGROUND

COVID-19 pandemic information is critical in order to study it further, but the virus has still not been confined. In addition, even if there is no longer any threat, more knowledge may be gathered from these resources.

METHODS

The data used in this study was gathered from several scientific areas and the links between them. Due to the fact that the COVID-19 pandemic has not been fully contained and additional information can be gleaned from these references, bibliometric analysis of it is important.

RESULTS

In total 155 publications on the topic of "COVID-19" and the keyword "nanotechnology" were identified in the Scopus database between 2020 and 2021 in a network visualization map.

CONCLUSION

As a result, our analysis was conducted at the appropriate time to provide a comprehensive understanding of COVID-19 and nanotechnology and prospective research directions for medicinal chemistry.

Eco-friendly masks preferences during COVID-19 pandemic in Indonesia

Eco-friendly face mask is necessity to reduce the aggravates the environment due to increased face masks waste during COVID-19 pandemic. The successful eco-friendly masks development influenced by understanding of user’s need and effectiveness of communications. The employed conjoint analysis obtained user mask preferences information to support effective communication strategies by business enterprises and policy makers on encouraging public to consume appropriate masks. The attribute importance followed from eco-friendly (32.1%), mask certification (26.5%), filtration efficiency (19.8%), price (13.9%), layers (5.6%), type of mask (1.5%), material (0.7%). The public expecting the mask with the ability to recycled and biodegradable, with certification, performance above 90% filtration efficiency, and affordable prices in the range of Rp.1.500-Rp.25.000. Also, 3-ply fabrics for the medical type and cotton material are generally preferred to polyester/polypropylene. The government needs to improve the effectiveness masks education, provide convenience process to masks certification by manufacturers, and provision of incentives to reduce masks production cost. Meanwhile, manufacturers ensure produce of the standard eco-friendly masks in affordable pricing. Furthermore, gender did not show significant effect on preferences, but varied with average expenditure.

Wearing time and respiratory volume affect the filtration efficiency of masks against aerosols at different sizes

Face masks are critical in preventing the spread of respiratory infections including coronavirus disease 2019 (COVID-19). Different types of masks have distinct filtration efficiencies (FEs) with differential costs and supplies. Here we reported the impact of breathing volume and wearing time on the inward and outward FEs of four different mask types (N95, surgical, single-use, and cloth masks) against various sizes of aerosols. Specifically, 1) Mask type was an important factor affecting the FEs. The FEs of N95 and surgical mask were better than those of single-use mask and cloth mask; 2) As particle size decreased, the FEs tended to reduce. The trend was significantly observed in FEs of aerosols with particle size < 1 μ m ; 3) After wearing N95 and surgical masks for 0, 2, 4, and 8 h, their FEs (%) maintained from 95.75 ± 0.09 to 100 ± 0 range. While a significant decrease in FEs were noticed for single-use masks worn for 8 h and cloth masks worn >2 h under deep breathing (30 L/min); 4) Both inward and outward FEs of N95 and surgical masks were similar, while the outward FEs of single-use and cloth masks were higher than their inward FEs; 5) The FEs under deep breathing was significantly lower than normal breathing with aerosol particle size <1 μ m. In conclusion, our results revealed that masks have a critical role in preventing the spread of aerosol particles by filtering inhalation, and FEs significantly decreased with the increasing of respiratory volume and wearing time. Deep breathing may cause increasing humidity and hence decrease FEs by increasing the airflow pressure. With the increase of wearing time, the adsorption capacity of the filter material tends to be saturated, which may reduce FEs. Findings may be used to provide information for policies regarding the proper use of masks for general public in current and future pandemics.

Efficacy of facemasks in mitigating respiratory exposure to submicron aerosols

We designed a novel experimental set-up to pseudo-simultaneously measure size-segregated filtration efficiency (η_F), breathing resistance (η_P) and potential usage time (t_B) for 11 types of face protective equipment (FPE; four respirators; three medical; and four handmade) in the submicron range. As expected, the highest η_F was exhibited by respirators (97 ± 3%), followed by medical (81 ± 7%) and handmade (47 ± 13%). Similarly, the breathing resistance was highest for respirators, followed by medical and handmade FPE. Combined analysis of efficiency and breathing resistance highlighted trade-offs, i.e. respirators showing the best overall performance across these two indicators, followed by medical and handmade FPE. This hierarchy was also confirmed by quality factor, which is a performance indicator of filters. Detailed assessment of size-segregated aerosols, combined with the scanning electron microscope imaging, revealed material characteristics such as pore density, fiber thickness, filter material and number of layers influence their performance. η_F and η_P showed an inverse exponential decay with time. Using their cross-over point, in combination with acceptable breathability, allowed to estimate t_B as 3.2-9.5 h (respirators), 2.6-7.3 h (medical masks) and 4.0-8.8 h (handmade). While relatively longer t_B of handmade FPE indicate breathing comfort, they are far less efficient in filtering virus-laden submicron aerosols compared with respirators.

Particle-Size-Dependent Filtration Efficiency, Breathability, and Flow Resistance of Face Coverings and Common Household Fabrics Used for Face Masks During the COVID-19 Pandemic

During the COVID-19 pandemic, the increase in demand for protective equipment caused a global shortage and homemade barrier face coverings were recommended as alternatives. However, filtration performances of homemade face coverings have not been fully evaluated. Test methods in the ASTM standard (F3502-21) were used to evaluate filtration efficiencies (FE) and breathability (pressure drop, Δp) of face coverings and home fabric materials commonly used during the pandemic. Submicron particulates FE was measured by particle transmission through face covering samples using a Condensation Particle Counter equipped with differential mobility analyzer and electronic manometer. Flow resistance of 0.1 μm-diameter fluorescent nanoparticles in droplets was determined by measuring fluorescence intensity of residual collected at the reverse side of samples. The size-dependent FE (3-94%) and Δp (0.8-72 mmH₂O) varied considerably among fabrics. Of the 16 mask types, 31.25% and 81.25% met the minimum FE and breathability standards in the ASTM F3502-21, respectively. Overall performance (qF) was highest for velcro masks (max qF = 3.36, min qF = 2.80) and lowest for Dutch wax print fabrics (max qF = 0.12, min qF = 0.03). Most of the samples resisted the flow of 0.1 µm-diameter nanoparticles in droplets. Low flow resistance was observed in bandana, neck gaiter, t-shirt I, tank top and bedspread fabrics. GSM and fabric finishing seems to affect performance. Low performances can be improved by selecting optimum-performance fabrics in the design and manufacture of barrier face coverings.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s41742-021-00390-6.

Purchase intention toward sustainable masks after COVID-19: the moderating role of health concern

This study aimed to investigate consumers’ intentions to purchase sustainable masks to reduce the environmental pollution caused by disposable masks in the context of COVID-19. A research model was derived based on the Value-Belief-Norm theory and the Theory of Planned Behavior, and the moderating role of health concerns and environmental knowledge due to the COVID-19 pandemic were examined. Through a Korean online survey company, we collected data on sustainable masks from respondents aged from their 20 s to 50 s, living in the Korea, and a structural equation analysis was performed on the 337 valid samples. Environmental concerns and beliefs were found to have a positive impact on the purchase intention on sustainable masks. Although environmental knowledge played the role of a moderator, we found that the higher the health concern, the stronger the purchase intention. Based on these results, it is possible to derive a strategy to increase the purchase of sustainable masks and reduce the environmental pollution caused by disposable masks. A sales strategy should be implemented for groups with high health concern. In addition, since the subjective norm increases the purchase intention for sustainable masks, advertising that stimulates them will help reduce environmental pollution caused by disposal masks. In the future, it will be possible to help reduce environmental pollution not only during the COVID-19 pandemic, but also during other emerging pandemics.

Assessment of cloth masks ability to limit Covid-19 particles spread: a systematic review

After the spread of Covid 19 worldwide, the use of cloth masks increased significantly due to a shortage of medical masks. Meanwhile, there were different opinions about the effectiveness of these masks and, so far, no study has been done to find the best fabric masks. This study reviews and summarizes all studies related to fabric masks' effectiveness and various fabrics against coronavirus. This systematic review is based on PRISMA rules. Two researchers separately examined three databases: PubMed, Scopus, and Web of Science. Laboratory and clinical studies were included. After extracting the articles, their quality was assessed with the Joanna Briggs Institute (JBI) tool. In addition to efficacy, other factors, including the penetration of masks, pressure drop, and quality factor, were examined to select the best fabrics. Of the 42 studies selected, 39 were laboratory studies, and 3 were clinical studies. Among the various fabrics examined, cotton quilt 120 thread per inch (TPI), copy paper (bonded), hybrid of cotton with chiffon/ silk, and flannel filtration were found to have over 90% effectiveness in the particle size range of Covid-19. The results and comparison of different factors (pressure drop, filtration efficacy, penetration, filtration quality, and fit factor have been evaluated) showed that among different fabrics, hybrid masks, 2-layered cotton quilt, 2-layered 100% cotton, cotton flannel, and hairy tea towel + fleece sweater had the best performance. Clinical studies have not explicitly examined cloth masks' effectiveness in Covid-19, so the effectiveness of these types of masks for Covid 19 is questionable, and more studies are needed.