1
|
Kim J, Im JH, So S, Choi Y, Kang H, Lim B, Lee M, Kim YK, Rho J. Dynamic Hyperspectral Holography Enabled by Inverse-Designed Metasurfaces with Oblique Helicoidal Cholesterics. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2024; 36:e2311785. [PMID: 38456592 DOI: 10.1002/adma.202311785] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/07/2023] [Revised: 02/16/2024] [Indexed: 03/09/2024]
Abstract
Metasurfaces are flat arrays of nanostructures that allow exquisite control of phase and amplitude of incident light. Although metasurfaces offer new active element for both fundamental science and applications, the challenge still remains to overcome their low information capacity and passive nature. Here, by integrating an inverse-designed-metasurface with oblique helicoidal cholesteric liquid crystal (ChOH), simultaneous spatial and spectral tunable metasurfaces with a high information capacity for dynamic hyperspectral holography, are demonstrated. The inverse design facilitates a single-phase map encoding of ten independent holographic images at different wavelengths. ChOH provides precise spectral modulation with narrow bandwidth and wide tunable regime in response to programmed stimuli, thus enabling dynamic switching of the multicolor holography. The results provide simple and generalizable principles for the rational design of interactive metasurfaces that will find numerous applications, including security platform.
Collapse
Affiliation(s)
- Joohoon Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Jun-Hyung Im
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Sunae So
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Graduate School of Artificial Intelligence, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Department of Control and Instrumentation Engineering, Korea University, Sejong, 30019, Republic of Korea
| | - Yeongseon Choi
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Hyunjung Kang
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Bogyu Lim
- Department of Engineering Chemistry, Chungbuk National University, Cheongju, 28644, Republic of Korea
| | - Minjae Lee
- Department of Chemistry, Kunsan National University, Gunsan, 54150, Republic of Korea
| | - Young-Ki Kim
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Junsuk Rho
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Department of Electrical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang, 37673, Republic of Korea
- National Institute of Nanomaterials Technology (NINT), Pohang, 37673, Republic of Korea
| |
Collapse
|
2
|
Yin Y, Jiang Q, Wang H, Liu J, Xie Y, Wang Q, Wang Y, Huang L. Multi-Dimensional Multiplexed Metasurface Holography by Inverse Design. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2024; 36:e2312303. [PMID: 38372628 DOI: 10.1002/adma.202312303] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/17/2023] [Revised: 02/05/2024] [Indexed: 02/20/2024]
Abstract
Multi-dimensional multiplexed metasurface holography extends holographic information capacity and promises revolutionary advancements for vivid imaging, information storage, and encryption. However, achieving multifunctional metasurface holography by forward design method is still difficult because it relies heavily on Jones matrix engineering, which places high demands on physical knowledge and processing technology. To break these limitations and simplify the design process, here, an end-to-end inverse design framework is proposed. By directly linking the metasurface to the reconstructed images and employing a loss function to guide the update of metasurface, the calculation of hologram can be omitted; thus, greatly simplifying the design process. In addition, the requirements on the completeness of meta-library can also be significantly reduced, allowing multi-channel hologram to be achieved using meta-atoms with only two degrees of freedom, which is very friendly to processing. By exploiting the proposed method, metasurface hologram containing up to 12 channels of multi-wavelength, multi-plane, and multi-polarization is designed and experimentally demonstrated, which exhibits the state-of-the-art information multiplexing capacity of the metasurface composed of simple meta-atoms. This method is conducive to promoting the intelligent design of multifunctional meta-devices, and it is expected to eventually accelerate the application of meta-devices in colorful display, imaging, storage and other fields.
Collapse
Affiliation(s)
- Yongyao Yin
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing, 100081, China
| | - Qiang Jiang
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing, 100081, China
| | - Hongbo Wang
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing, 100081, China
| | - Jianghong Liu
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing, 100081, China
| | - Yiyang Xie
- Optoelectronics Technology, Ministry of Education, Beijing University of Technology, Beijing, 100124, China
| | - Qiuhua Wang
- Key Laboratory of Semiconductor Materials Science, Institute of Semiconductors, Chinese Academy of Sciences, Beijing, 100083, China
| | - Yongtian Wang
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing, 100081, China
| | - Lingling Huang
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing, 100081, China
| |
Collapse
|
3
|
Wang K, Liao D, Wang H. Reconfigurable origami hologram based on deep neural networks. OPTICS LETTERS 2024; 49:2041-2044. [PMID: 38621071 DOI: 10.1364/ol.520781] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/05/2024] [Accepted: 03/17/2024] [Indexed: 04/17/2024]
Abstract
Reconfigurable and multifunctional metasurfaces are becoming indispensable in a variety of applications due to their capability to execute diverse functions across various states. However, many of these metasurfaces incorporate complex active components, thereby escalating structural complexity and bulk volume. In this research, we propose a reconfigurable passive hologram based solely on an origami structure, enabling the successful generation of holograms depicting the 'Z' and 'L' illuminated by a right-hand circular polarization (RHCP) wave in two distinct states: planar and zigzag configuration, respectively. The transformation between the 2D planar metasurface and the 3D zigzag structure with slant angles of 35 is achieved solely through mechanically stretching and compressing the origami metasurface. The phases on the origami metasurface are trained through a deep neural network which operates on the NVIDIA Tesla k80 GPU, with the total training process costing 11.88 s after 100 epochs. The reconfigurable scheme proposed in this research provides flexibility and ease of implementation in the fields of imaging and data processing.
Collapse
|
4
|
Yang Z, Huang PS, Lin YT, Qin H, Chen J, Han S, Huang W, Deng ZL, Li B, Zúñiga-Pérez J, Genevet P, Wu PC, Song Q. Asymmetric Full-Color Vectorial Meta-holograms Empowered by Pairs of Exceptional Points. NANO LETTERS 2024; 24:844-851. [PMID: 38190513 DOI: 10.1021/acs.nanolett.3c03611] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 01/10/2024]
Abstract
Holography holds tremendous promise in applications such as immersive virtual reality and optical communications. With the emergence of optical metasurfaces, planar optical components that have the remarkable ability to precisely manipulate the amplitude, phase, and polarization of light on the subwavelength scale have expanded the potential applications of holography. However, the realization of metasurface-based full-color vectorial holography remains particularly challenging. Here, we report a general approach utilizing a modified Gerchberg-Saxton algorithm to achieve spatially aligned full-color display and incorporating wavelength information with an image compensation strategy. We combine the Pancharatnam-Berry phase and pairs of exceptional points to address the issue of redundant twin images that generally appear for the two orthogonal circular polarizations and to enable full polarization control of the vectorial field. Our results enable the realization of an asymmetric full-color vectorial meta-hologram, paving the way for the development of full-color display, complex beam generation, and secure data storage applications.
Collapse
Affiliation(s)
- Zijin Yang
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen 518055, China
- School of Materials Science and Engineering, Tsinghua University, Beijing 100084, China
| | - Po-Sheng Huang
- Department of Photonics, National Cheng Kung University, Tainan 70101, Taiwan
| | - Yu-Tsung Lin
- Department of Photonics, National Cheng Kung University, Tainan 70101, Taiwan
| | - Haoye Qin
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen 518055, China
| | - Jiaxin Chen
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen 518055, China
- School of Materials Science and Engineering, Tsinghua University, Beijing 100084, China
| | - Sanyang Han
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen 518055, China
| | - Wei Huang
- Key Laboratory of Multifunctional Nanomaterials and Smart Systems, Suzhou Institute of NanoTech and Nano-Bionics (SINANO), Chinese Academy of Sciences (CAS), Suzhou 215123, China
| | - Zi-Lan Deng
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 510632, China
| | - Bo Li
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen 518055, China
- Suzhou Laboratory, Suzhou 215123, China
| | - Jesús Zúñiga-Pérez
- Université Cote d'Azur, CNRS, CRHEA, Rue Bernard Gregory, Sophia Antipolis, 06560 Valbonne, France
- Majulab, International Research Laboratory IRL 3654, CNRS, Université Côte d'Azur, Sorbonne Université, National University of Singapore, Nanyang Technological University, Singapore 117543
- Division of Physics and Applied Physics, School of Physical and Mathematical Sciences, Nanyang Technological University, Singapore 637371
| | - Patrice Genevet
- Université Cote d'Azur, CNRS, CRHEA, Rue Bernard Gregory, Sophia Antipolis, 06560 Valbonne, France
- Physics Department, Colorado School of Mines, 1523 Illinois Street, Golden, Colorado 80401, United States
| | - Pin Chieh Wu
- Department of Photonics, National Cheng Kung University, Tainan 70101, Taiwan
- Center for Quantum Frontiers of Research & Technology (QFort), National Cheng Kung University, Tainan 70101, Taiwan
- Meta-nanoPhotonics Center, National Cheng Kung University, Tainan 70101, Taiwan
| | - Qinghua Song
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen 518055, China
- Suzhou Laboratory, Suzhou 215123, China
| |
Collapse
|
5
|
Yang Z, Huang PS, Lin YT, Qin H, Zúñiga-Pérez J, Shi Y, Wang Z, Cheng X, Tang MC, Han S, Kanté B, Li B, Wu PC, Genevet P, Song Q. Creating pairs of exceptional points for arbitrary polarization control: asymmetric vectorial wavefront modulation. Nat Commun 2024; 15:232. [PMID: 38177166 PMCID: PMC10766979 DOI: 10.1038/s41467-023-44428-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/07/2022] [Accepted: 12/13/2023] [Indexed: 01/06/2024] Open
Abstract
Exceptional points (EPs) can achieve intriguing asymmetric control in non-Hermitian systems due to the degeneracy of eigenstates. Here, we present a general method that extends this specific asymmetric response of EP photonic systems to address any arbitrary fully-polarized light. By rotating the meta-structures at EP, Pancharatnam-Berry (PB) phase can be exclusively encoded on one of the circular polarization-conversion channels. To address any arbitrary wavefront, we superpose the optical signals originating from two orthogonally polarized -yet degenerate- EP eigenmodes. The construction of such orthogonal EP eigenstates pairs is achieved by applying mirror-symmetry to the nanostructure geometry flipping thereby the EP eigenmode handedness from left to right circular polarization. Non-Hermitian reflective PB metasurfaces designed using such EP superposition enable arbitrary, yet unidirectional, vectorial wavefront shaping devices. Our results open new avenues for topological wave control and illustrate the capabilities of topological photonics to distinctively operate on arbitrary polarization-state with enhanced performances.
Collapse
Affiliation(s)
- Zijin Yang
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, 518055, China
- School of Materials Science and Engineering, Tsinghua University, Beijing, 100084, China
| | - Po-Sheng Huang
- Department of Photonics, National Cheng Kung University, Tainan, 70101, Taiwan
| | - Yu-Tsung Lin
- Department of Photonics, National Cheng Kung University, Tainan, 70101, Taiwan
| | - Haoye Qin
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, 518055, China
| | - Jesús Zúñiga-Pérez
- Université Cote d'Azur, CNRS, CRHEA, Rue Bernard Gregory, Sophia Antipolis, 06560, Valbonne, France
- Majulab, International Research Laboratory IRL 3654, CNRS, Université Côte d'Azur, Sorbonne Université, National University of Singapore, Nanyang Technological University, Singapore, Singapore
| | - Yuzhi Shi
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai, 200092, China
| | - Zhanshan Wang
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai, 200092, China
| | - Xinbin Cheng
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai, 200092, China
| | - Man-Chung Tang
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, 518055, China
| | - Sanyang Han
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, 518055, China
| | - Boubacar Kanté
- Department of Electrical Engineering and Computer Sciences, University of California, Berkeley, CA, 94720, USA
| | - Bo Li
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, 518055, China
- Suzhou Laboratory, Suzhou, 215123, China
| | - Pin Chieh Wu
- Department of Photonics, National Cheng Kung University, Tainan, 70101, Taiwan.
- Center for Quantum Frontiers of Research & Technology (QFort), National Cheng Kung University, Tainan, 70101, Taiwan.
- Meta-nanoPhotonics Center, National Cheng Kung University, Tainan, 70101, Taiwan.
| | - Patrice Genevet
- Université Cote d'Azur, CNRS, CRHEA, Rue Bernard Gregory, Sophia Antipolis, 06560, Valbonne, France.
- Physics Department, Colorado School of Mines, 1523 Illinois St., Golden, CO, 80401, USA.
| | - Qinghua Song
- Tsinghua Shenzhen International Graduate School, Tsinghua University, Shenzhen, 518055, China.
- Suzhou Laboratory, Suzhou, 215123, China.
| |
Collapse
|
6
|
Zou Y, Jin H, Zhu R, Zhang T. Metasurface Holography with Multiplexing and Reconfigurability. NANOMATERIALS (BASEL, SWITZERLAND) 2023; 14:66. [PMID: 38202521 PMCID: PMC10780441 DOI: 10.3390/nano14010066] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/29/2023] [Revised: 12/22/2023] [Accepted: 12/23/2023] [Indexed: 01/12/2024]
Abstract
Metasurface holography offers significant advantages, including a broad field of view, minimal noise, and high imaging quality, making it valuable across various optical domains such as 3D displays, VR, and color displays. However, most passive pure-structured metasurface holographic devices face a limitation: once fabricated, as their functionality remains fixed. In recent developments, the introduction of multiplexed and reconfigurable metasurfaces breaks this limitation. Here, the comprehensive progress in holography from single metasurfaces to multiplexed and reconfigurable metasurfaces is reviewed. First, single metasurface holography is briefly introduced. Second, the latest progress in angular momentum multiplexed metasurface holography, including basic characteristics, design strategies, and diverse applications, is discussed. Next, a detailed overview of wavelength-sensitive, angle-sensitive, and polarization-controlled holograms is considered. The recent progress in reconfigurable metasurface holography based on lumped elements is highlighted. Its instant on-site programmability combined with machine learning provides the possibility of realizing movie-like dynamic holographic displays. Finally, we briefly summarize this rapidly growing area of research, proposing future directions and potential applications.
Collapse
Affiliation(s)
- Yijun Zou
- Interdisciplinary Center for Quantum Information, State Key Laboratory of Modern Optical Instrumentation, ZJU-Hangzhou Global Scientific and Technological Innovation Center, Zhejiang University, Hangzhou 310027, China; (Y.Z.); (H.J.); (R.Z.)
| | - Hui Jin
- Interdisciplinary Center for Quantum Information, State Key Laboratory of Modern Optical Instrumentation, ZJU-Hangzhou Global Scientific and Technological Innovation Center, Zhejiang University, Hangzhou 310027, China; (Y.Z.); (H.J.); (R.Z.)
| | - Rongrong Zhu
- Interdisciplinary Center for Quantum Information, State Key Laboratory of Modern Optical Instrumentation, ZJU-Hangzhou Global Scientific and Technological Innovation Center, Zhejiang University, Hangzhou 310027, China; (Y.Z.); (H.J.); (R.Z.)
- School of Information and Electrical Engineering, Zhejiang University City College, Hangzhou 310015, China
| | - Ting Zhang
- College of Information Science & Electronic Engineering, Zhejiang Provincial Key Laboratory of Information Processing, Communication and Networking (IPCN), Zhejiang University, Hangzhou 310027, China
| |
Collapse
|
7
|
Chu Y, Chen C, Xiao X, Shen W, Ye X, Zhu S, Li T. Full-space wavefront control enabled by a bilayer metasurface sandwiching 1D photonic crystal. OPTICS LETTERS 2023; 48:5895-5898. [PMID: 37966746 DOI: 10.1364/ol.501949] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/28/2023] [Accepted: 10/15/2023] [Indexed: 11/16/2023]
Abstract
Metasurfaces, composed of sub-wavelength structures, have a powerful capability to manipulate light propagations. However, metasurfaces usually work either in pure reflection mode or pure transmission mode. Achieving full-space manipulation of light at will in the optical region is still challenging. Here we propose a design method of full-space meta-device containing a bilayer metasurface sandwiching 1D photonic crystal to manipulate the transmitted and reflected wave independently. To provide a proof-of-concept demonstration, a device is proposed to show the light focusing in transmission and a vortex beam in reflection. Meanwhile, a device focusing the reflected light with oblique 45° incidence and the transmitted light with normal incidence is designed to indicate its application potential in augmented reality (AR) application. Our design provides a promising way to enrich the multifunctional meta-devices for potential applications.
Collapse
|
8
|
Freire-Fernández F, Reese T, Rhee D, Guan J, Li R, Schaller RD, Schatz GC, Odom TW. Quasi-Random Multimetallic Nanoparticle Arrays. ACS NANO 2023; 17:21905-21911. [PMID: 37870944 DOI: 10.1021/acsnano.3c08247] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 10/25/2023]
Abstract
This paper describes a nanofabrication procedure that can generate multiscale substrates with quasi-random microregions of nanoparticle arrays having different periodicities and metals. We combine cycles of large-area nanoparticle array fabrication with solvent-assisted wrinkle lithography to mask and etch quasi-random areas of prefabricated nanoparticles to control the fill factors of the arrays. The approach is highly flexible, and parameters, including nanoparticle size and material, array geometry, and fill factor, can be tailored independently. Multimetallic nanoparticle arrays can support surface lattice resonances at fill factors as low as 20% and can function as nanoscale cavities for lasing action with as few as 10% of the nanoparticles in an array. We demonstrated that multimetallic nanoparticle substrates that combine two or three arrays with different periodicities can exhibit lasing responses over visible and near-infrared wavelengths. Our work showcases the robust optical responses of multimetallic and periodic devices for broadband light manipulation.
Collapse
Affiliation(s)
| | | | | | | | | | - Richard D Schaller
- Center for Nanoscale Materials, Argonne National Laboratory, Argonne, Illinois 60439, United States of America
| | | | | |
Collapse
|
9
|
Hu Y, Jiang Y, Zhang Y, Yang X, Ou X, Li L, Kong X, Liu X, Qiu CW, Duan H. Asymptotic dispersion engineering for ultra-broadband meta-optics. Nat Commun 2023; 14:6649. [PMID: 37863896 PMCID: PMC10589226 DOI: 10.1038/s41467-023-42268-5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/07/2022] [Accepted: 10/04/2023] [Indexed: 10/22/2023] Open
Abstract
Dispersion decomposes compound light into its monochromatic components, which is detrimental to broadband imaging but advantageous for spectroscopic applications. Metasurfaces provide a unique path to modulate the dispersion by adjusting structural parameters on a two-dimensional plane. However, conventional linear phase compensation does not adequately match the meta-unit's dispersion characteristics with required complex dispersion, hindering at-will dispersion engineering over a very wide bandwidth particularly. Here, we propose an asymptotic phase compensation strategy for ultra-broadband dispersion-controlled metalenses. Metasurfaces with extraordinarily high aspect ratio nanostructures have been fabricated for arbitrary dispersion control in ultra-broad bandwidth, and we experimentally demonstrate the single-layer achromatic metalenses in the visible to infrared spectrum (400 nm~1000 nm, NA = 0.164). Our proposed scheme provides a comprehensive theoretical framework for single-layer meta-optics, allowing for arbitrary dispersion manipulation without bandwidth restrictions. This development is expected to have significant applications in ultra-broadband imaging and chromatography detection, among others.
Collapse
Affiliation(s)
- Yueqiang Hu
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China
- Advanced Manufacturing Laboratory of Micro-Nano Optical Devices, Shenzhen Research Institute, Hunan University, Shenzhen, 518000, PR China
| | - Yuting Jiang
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China
| | - Yi Zhang
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China
| | - Xing Yang
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China
| | - Xiangnian Ou
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China
| | - Ling Li
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China
| | - Xianghong Kong
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore, Singapore
| | - Xingsi Liu
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore, Singapore
| | - Cheng-Wei Qiu
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore, Singapore.
| | - Huigao Duan
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082, PR China.
- Advanced Manufacturing Laboratory of Micro-Nano Optical Devices, Shenzhen Research Institute, Hunan University, Shenzhen, 518000, PR China.
- Greater Bay Area Institute for Innovation, Hunan University, Guangzhou, 511300, PR China.
| |
Collapse
|
10
|
So S, Mun J, Park J, Rho J. Revisiting the Design Strategies for Metasurfaces: Fundamental Physics, Optimization, and Beyond. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2023; 35:e2206399. [PMID: 36153791 DOI: 10.1002/adma.202206399] [Citation(s) in RCA: 5] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/14/2022] [Revised: 09/13/2022] [Indexed: 06/16/2023]
Abstract
Over the last two decades, the capabilities of metasurfaces in light modulation with subwavelength thickness have been proven, and metasurfaces are expected to miniaturize conventional optical components and add various functionalities. Herein, various metasurface design strategies are reviewed thoroughly. First, the scalar diffraction theory is revisited to provide the basic principle of light propagation. Then, widely used design methods based on the unit-cell approach are discussed. The methods include a set of simplified steps, including the phase-map retrieval and meta-atom unit-cell design. Then, recently emerging metasurfaces that may not be accurately designed using unit-cell approach are introduced. Unconventional metasurfaces are examined where the conventional design methods fail and finally potential design methods for such metasurfaces are discussed.
Collapse
Affiliation(s)
- Sunae So
- Graduate School of Artificial Intelligence, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Jungho Mun
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Junghyun Park
- Samsung Advanced Institute of Technology, Samsung Electronics, Suwon, 16678, Republic of Korea
| | - Junsuk Rho
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang, 37673, Republic of Korea
| |
Collapse
|
11
|
Ren H, Maier SA. Nanophotonic Materials for Twisted-Light Manipulation. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2023; 35:e2106692. [PMID: 34716627 DOI: 10.1002/adma.202106692] [Citation(s) in RCA: 11] [Impact Index Per Article: 11.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/25/2021] [Revised: 10/14/2021] [Indexed: 06/13/2023]
Abstract
Twisted light, an unbounded set of helical spatial modes carrying orbital angular momentum (OAM), offers not only fundamental new insights into structured light-matter interactions, but also a new degree of freedom to boost optical and quantum information capacity. However, current OAM experiments still rely on bulky, expensive, and slow-response diffractive or refractive optical elements, hindering today's OAM systems to be largely deployed. In the last decade, nanophotonics has transformed the photonic design and unveiled a diverse range of compact and multifunctional nanophotonic devices harnessing the generation and detection of OAM modes. Recent metasurface devices developed for OAM generation in both real and momentum space, presenting design principle and exemplary devices, are summarized. Moreover, recent development of whispering-gallery-mode-based passive and tunable microcavities, capable of extracting degenerate OAM modes for on-chip vortex emission and lasing, is summarized. In addition, the design principle of different plasmonic devices and photodetectors recently developed for on-chip OAM detection is discussed. Current challenges faced by the nanophotonic field for twisted-light manipulation and future advances to meet these challenges are further discussed. It is believed that twisted-light manipulation in nanophotonics will continue to make significant impact on future development of ultracompact, ultrahigh-capacity, and ultrahigh-speed OAM systems-on-a-chip.
Collapse
Affiliation(s)
- Haoran Ren
- MQ Photonics Research Centre, Department of Physics and Astronomy, Macquarie University, Macquarie Park, NSW, 2109, Australia
| | - Stefan A Maier
- Chair in Hybrid Nanosystems, Nanoinstitute Munich, Faculty of Physics, Ludwig-Maximilians-University Munich, 80539, Munich, Germany
- Department of Physics, Imperial College London, London, SW7 2AZ, UK
| |
Collapse
|
12
|
Tsai WC, Hong YH, Kuo HC, Huang YW. Design of high-efficiency and large-angle homo-metagratings for light source integration. OPTICS EXPRESS 2023; 31:24404-24411. [PMID: 37475268 DOI: 10.1364/oe.496042] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/19/2023] [Accepted: 07/01/2023] [Indexed: 07/22/2023]
Abstract
Meta-optics integrated with light sources has gained significant attention. However, most focused on the efficiency of metasurfaces themselves, rather than the efficiency of integration. To design highly efficient beam deflection, we develop a scheme of homo-metagrating, involving the same material for meta-atoms, substrate, and top layer of the laser, to achieve near-unity power from light-emitting to metasurfaces. We utilize three degrees of freedom: overall add-on phase, parameters of meta-atoms in a period, and lattice arrangement. The overall efficiency of homo-metagratings is higher than that of hetero-metagratings. We believe our approach is capable of being implemented in various ultracompact optic systems.
Collapse
|
13
|
Hsu WC, Chang CH, Hong YH, Kuo HC, Huang YW. Compact structured light generation based on meta-hologram PCSEL integration. DISCOVER NANO 2023; 18:87. [PMID: 37382858 DOI: 10.1186/s11671-023-03866-w] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/21/2023] [Accepted: 06/09/2023] [Indexed: 06/30/2023]
Abstract
Metasurfaces, a catalog of optical components, offer numerous novel functions on demand. They have been integrated with vertical cavity surface-emitting lasers (VCSELs) in previous studies. However, the performance has been limited by the features of the VCSELs such as low output power and large divergence angle. Although the solution of the module of VCSEL array could solve these issues, the practical application is limited by extra lens and large size. In this study, we experimentally demonstrate reconstruction of a holographic images using a compact integration of a photonic crystal surface-emitting laser and metasurface holograms designed for structured light generation. This research showcases the flexible design capabilities of metasurfaces, high output power (on the order of milliwatts), and the ability to produce well-uniformed images with a wide field of view without the need for a collection lens, making it suitable for 3D imaging and sensing.
Collapse
Affiliation(s)
- Wen-Cheng Hsu
- Department of Photonics, College of Electrical and Computer Engineering, National Yang Ming Chiao Tung University, Hsinchu, 30010, Taiwan
- Semiconductor Research Center, Hon Hai Research Institute, Taipei, 11492, Taiwan
| | - Chia-Hsun Chang
- Department of Photonics, College of Electrical and Computer Engineering, National Yang Ming Chiao Tung University, Hsinchu, 30010, Taiwan
| | - Yu-Heng Hong
- Semiconductor Research Center, Hon Hai Research Institute, Taipei, 11492, Taiwan.
| | - Hao-Chung Kuo
- Department of Photonics, College of Electrical and Computer Engineering, National Yang Ming Chiao Tung University, Hsinchu, 30010, Taiwan.
- Semiconductor Research Center, Hon Hai Research Institute, Taipei, 11492, Taiwan.
| | - Yao-Wei Huang
- Department of Photonics, College of Electrical and Computer Engineering, National Yang Ming Chiao Tung University, Hsinchu, 30010, Taiwan.
| |
Collapse
|
14
|
Yang W, Chen K, Dong S, Wang S, Qu K, Jiang T, Zhao J, Feng Y. Direction-Duplex Janus Metasurface for Full-Space Electromagnetic Wave Manipulation and Holography. ACS APPLIED MATERIALS & INTERFACES 2023. [PMID: 37224443 DOI: 10.1021/acsami.3c04382] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/26/2023]
Abstract
Janus metasurfaces, a category of two-faced two-dimensional (2D) materials, are emerging as a promising platform for designing multifunctional metasurfaces by exploring the intrinsic propagation direction (k-direction) of electromagnetic waves. Their out-of-plane asymmetry is utilized for achieving distinct functions selectively excited by choosing the propagation directions, providing an effective strategy to meet the growing demand for the integration of more functionalities into a single optoelectronic device. Here, we propose the concept of direction-duplex Janus metasurface for full-space wave control yielding drastically different transmission and reflection wavefronts for the same polarized incidence with opposite k-directions. A series of Janus metasurface devices that enable asymmetric full-space wave manipulations, such as integrated metalens, beam generators, and fully direction-duplex meta-holography, are experimentally demonstrated. We envision the Janus metasurface platform proposed here to open new possibilities toward a broader exploration of creating sophisticated multifunctional meta-devices ranging from microwaves to optical systems.
Collapse
Affiliation(s)
- Weixu Yang
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Ke Chen
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Shufang Dong
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Shaojie Wang
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Kai Qu
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Tian Jiang
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Junming Zhao
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| | - Yijun Feng
- School of Electronic Science and Engineering, Nanjing University, Nanjing 210023, China
| |
Collapse
|
15
|
Zhang Q, Wang J, Xie R, Gu Z, Zhang Z, Wang X, Zhang H, Chen C, Chen W, Ding J, Zhang X. Four-channel joint-polarization-frequency-multiplexing encryption meta-hologram based on dual-band polarization multiplexing meta-atoms. OPTICS EXPRESS 2023; 31:17569-17579. [PMID: 37381487 DOI: 10.1364/oe.487483] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/10/2023] [Accepted: 04/22/2023] [Indexed: 06/30/2023]
Abstract
Holography is an advanced imaging technology where image information can be reconstructed without a lens. Recently, multiplexing techniques have been widely adapted to realize multiple holographic images or functionalities in a meta-hologram. In this work, a reflective four-channel meta-hologram is proposed to further increase the channel capacity by simultaneously implementing frequency and polarization multiplexing. Compared to the single multiplexing technique, the number of channels achieves a multiplicative growth of the two multiplexing techniques, as well as allowing meta-devices to possess cryptographic characteristics. Specifically, spin-selective functionalities for circular polarizations can be achieved at lower frequency, while different functionalities can be obtained at higher frequency under different linearly polarized incidences. As an illustrative example, a four-channel joint-polarization-frequency-multiplexing meta-hologram is designed, fabricated, and characterized. The measured results agree well with the numerically calculated and full-wave simulated ones, which provides the proposed method with great potential in numerous opportunities such as multi-channel imaging and information encryption technology.
Collapse
|
16
|
Asad A, Kim J, Khaliq HS, Mahmood N, Akbar J, Chani MTS, Kim Y, Jeon D, Zubair M, Mehmood MQ, Massoud Y, Rho J. Spin-isolated ultraviolet-visible dynamic meta-holographic displays with liquid crystal modulators. NANOSCALE HORIZONS 2023; 8:759-766. [PMID: 37128758 DOI: 10.1039/d2nh00555g] [Citation(s) in RCA: 4] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/03/2023]
Abstract
Wearable displays or head-mounted displays (HMDs) have the ability to create a virtual image in the field of view of one or both eyes. Such displays constitute the main platform for numerous virtual reality (VR)- and augmented reality (AR)-based applications. Meta-holographic displays integrated with AR technology have potential applications in the advertising, media, and healthcare sectors. In the previous decade, dielectric metasurfaces emerged as a suitable choice for designing compact devices for highly efficient displays. However, the small conversion efficiency, narrow bandwidth, and costly fabrication procedures limit the device's functionalities. Here, we proposed a spin-isolated dielectric multi-functional metasurface operating at broadband optical wavelengths with high transmission efficiency in the ultraviolet (UV) and visible (Vis) regimes. The proposed metasurface comprised silicon nitride (Si3N4)-based meta-atoms with high bandgap, i.e., ∼ 5.9 eV, and encoded two holographic phase profiles. Previously, the multiple pieces of holographic information incorporated in the metasurfaces using interleaved and layer stacking techniques resulted in noisy and low-efficiency outputs. A single planar metasurface integrated with a liquid crystal was demonstrated numerically and experimentally in the current work to validate the spin-isolated dynamic UV-Vis holographic information at broadband wavelengths. In our opinion, the proposed metasurface can have promising applications in healthcare, optical security encryption, anti-counterfeiting, and UV-Vis nanophotonics.
Collapse
Affiliation(s)
- Aqsa Asad
- MicroNano Lab, Department of Electrical Engineering, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan.
| | - Joohoon Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Hafiz Saad Khaliq
- MicroNano Lab, Department of Electrical Engineering, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan.
- School of Electronic and Electrical Engineering, Kyungpook National University, Daegu 41566, Republic of Korea
| | - Nasir Mahmood
- Innovative Technologies Laboratories (ITL), King Abdullah University of Science and Technology (KAUST), Saudi Arabia
| | - Jehan Akbar
- Glasgow College, University of Electronic Science and Technology of China, Chengdu 610056, China
| | | | - Yeseul Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Dongmin Jeon
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Muhammad Zubair
- Innovative Technologies Laboratories (ITL), King Abdullah University of Science and Technology (KAUST), Saudi Arabia
| | - Muhammad Qasim Mehmood
- MicroNano Lab, Department of Electrical Engineering, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan.
| | - Yehia Massoud
- Innovative Technologies Laboratories (ITL), King Abdullah University of Science and Technology (KAUST), Saudi Arabia
| | - Junsuk Rho
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
- POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang 37673, Republic of Korea
- National Institute of Nanomaterials Technology (NINT), Pohang 37673, Republic of Korea
| |
Collapse
|
17
|
So S, Kim J, Badloe T, Lee C, Yang Y, Kang H, Rho J. Multicolor and 3D Holography Generated by Inverse-Designed Single-Cell Metasurfaces. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2023; 35:e2208520. [PMID: 36575136 DOI: 10.1002/adma.202208520] [Citation(s) in RCA: 22] [Impact Index Per Article: 22.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/16/2022] [Revised: 12/17/2022] [Indexed: 05/17/2023]
Abstract
Metasurface-generated holography has emerged as a promising route for fully reproducing vivid scenes by manipulating the optical properties of light using ultra-compact devices. However, achieving multiple holographic images using a single metasurface is still difficult due to the capacity limit of a single meta-atom. In this work, an inverse design method based on gradient-descent optimization is presented to encode multiple pieces of holographic information into a single metasurface. The proposed method allows the inverse design of single-cell metasurfaces without the need for complex meta-atom design strategies, facilitating high-throughput fabrication using broadband low-loss materials. By exploiting the proposed design method, both multiplane red-green-blue (RGB) color and three-dimensional (3D) holograms are designed and experimentally demonstrated. Multiplane RGB color holograms with nine distinct holograms are achieved, which demonstrate the state-of-the-art data capacity of a phase-only metasurface. The first experimental demonstration of metasurface-generated 3D holograms with completely independent and distinct images in each plane is also presented. The current research findings provide a viable route for practical metasurface-generated holography by demonstrating the high-density holography produced by a single metasurface. It is expected to ultimately lead to optical storage, display, and full-color imaging applications.
Collapse
Affiliation(s)
- Sunae So
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Graduate School of Artificial Intelligence, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Department of Electro-Mechanical Systems Engineering, Korea University, Sejong, 30019, Republic of Korea
| | - Joohoon Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Trevon Badloe
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Graduate School of Artificial Intelligence, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Chihun Lee
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Younghwan Yang
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Hyunjung Kang
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
| | - Junsuk Rho
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, 37673, Republic of Korea
- POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang, 37673, Republic of Korea
- National Institute of Nanomaterials Technology (NINT), Pohang, 37673, Republic of Korea
| |
Collapse
|
18
|
Ou K, Wan H, Wang G, Zhu J, Dong S, He T, Yang H, Wei Z, Wang Z, Cheng X. Advances in Meta-Optics and Metasurfaces: Fundamentals and Applications. NANOMATERIALS (BASEL, SWITZERLAND) 2023; 13:1235. [PMID: 37049327 PMCID: PMC10097126 DOI: 10.3390/nano13071235] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 02/20/2023] [Revised: 03/20/2023] [Accepted: 03/23/2023] [Indexed: 06/19/2023]
Abstract
Meta-optics based on metasurfaces that interact strongly with light has been an active area of research in recent years. The development of meta-optics has always been driven by human's pursuits of the ultimate miniaturization of optical elements, on-demand design and control of light beams, and processing hidden modalities of light. Underpinned by meta-optical physics, meta-optical devices have produced potentially disruptive applications in light manipulation and ultra-light optics. Among them, optical metalens are most fundamental and prominent meta-devices, owing to their powerful abilities in advanced imaging and image processing, and their novel functionalities in light manipulation. This review focuses on recent advances in the fundamentals and applications of the field defined by excavating new optical physics and breaking the limitations of light manipulation. In addition, we have deeply explored the metalenses and metalens-based devices with novel functionalities, and their applications in computational imaging and image processing. We also provide an outlook on this active field in the end.
Collapse
Affiliation(s)
- Kai Ou
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
| | - Hengyi Wan
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
| | - Guangfeng Wang
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
| | - Jingyuan Zhu
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
| | - Siyu Dong
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
| | - Tao He
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
| | - Hui Yang
- National Research Center for High-Efficiency Grinding, College of Mechanical and Vehicle Engineering, Hunan University, Changsha 410082, China
| | - Zeyong Wei
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
| | - Zhanshan Wang
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
- Shanghai Institute of Intelligent Science and Technology, Tongji University, Shanghai 200092, China
| | - Xinbin Cheng
- Institute of Precision Optical Engineering, School of Physics Science and Engineering, Tongji University, Shanghai 200092, China
- MOE Key Laboratory of Advanced Micro-Structured Materials, Shanghai 200092, China
- Shanghai Frontiers Science Center of Digital Optics, Shanghai 200092, China
- Shanghai Institute of Intelligent Science and Technology, Tongji University, Shanghai 200092, China
| |
Collapse
|
19
|
Wei L, Huang H. Metasurface-based triple-band beam splitter with large spatial separation at visible wavelengths. JOURNAL OF THE OPTICAL SOCIETY OF AMERICA. A, OPTICS, IMAGE SCIENCE, AND VISION 2023; 40:583-589. [PMID: 37133041 DOI: 10.1364/josaa.480647] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/04/2023]
Abstract
The dual-function of a wavelength beam splitter and a power beam splitter is desired in both classical optics and quantum optics. We propose a triple-band large-spatial-separation beam splitter at visible wavelengths using a phase-gradient metasurface in both the x- and y-directions. Under x-polarized normal incidence, the blue light is split in the y-direction into two equal-intensity beams owing to the resonance inside a single meta-atom, the green light is split in the x-direction into another two equal-intensity beams owing to the size variation between adjacent meta-atoms, while the red light passes directly without splitting. The size of the meta-atoms was optimized based on their phase response and transmittance. The simulated working efficiencies under normal incidence are 68.1%, 85.0%, and 81.9% at the wavelengths of 420 nm, 530 nm, and 730 nm, respectively. The sensitivities of the oblique incidence and polarization angle are also discussed.
Collapse
|
20
|
Xu P, Xiao Y, Huang H, Yang T, Zhang X, Yuan X, Li XC, Xu H, Wang M. Dual-wavelength hologram of high transmittance metasurface. OPTICS EXPRESS 2023; 31:8110-8119. [PMID: 36859927 DOI: 10.1364/oe.482263] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/06/2022] [Accepted: 01/27/2023] [Indexed: 06/18/2023]
Abstract
In this work, a simple dielectric metasurface hologram is proposed and designed by combining the electromagnetic vector analysis method and the immune algorithm, which can realize the holographic display of dual wavelength orthogonal-linear polarization light in visible light band, solve the problem of low efficiency of the traditional design method of metasurface hologram, and effectively improve the diffraction efficiency of metasurface hologram. The titanium dioxide metasurface nanorod based on rectangular structure is optimized and designed. When the x-linear polarized light with wavelength of 532 nm and y-linear polarized light with wavelength of 633 nm are incident on the metasurface respectively, different display output images with low cross-talk can be obtained on the same observation plane, and the transmission efficiencies of x-linear and y-linear polarized light are as high as 68.2% and 74.6% respectively in simulation. Then the metasurface is fabricated by Atomic Layer Deposition method. The experimental results are consistent with the design results, which proves that the metasurface hologram designed by this method can completely realize the feasibility of wavelength and polarization multiplexing holographic display, and has potential application value in holographic display, optical encryption, anti-counterfeiting, data storage and other fields.
Collapse
|
21
|
Zhang L, Wang C, Wei Y, Lin Y, Han Y, Deng Y. High-Efficiency Achromatic Metalens Topologically Optimized in the Visible. NANOMATERIALS (BASEL, SWITZERLAND) 2023; 13:nano13050890. [PMID: 36903769 PMCID: PMC10005494 DOI: 10.3390/nano13050890] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/24/2023] [Revised: 02/17/2023] [Accepted: 02/19/2023] [Indexed: 06/12/2023]
Abstract
Metalens, composed of arrays of nano-posts, is an ultrathin planar optical element used for constructing compact optical systems which can achieve high-performance optical imaging by wavefront modulating. However, the existing achromatic metalenses for circular polarization possess the problem of low focal efficiency, which is caused by the low polarization conversion efficiencies of the nano-posts. This problem hinders the practical application of the metalens. Topology optimization is an optimization-based design method that can effectively extend the degree of design freedom, allowing the phases and polarization conversion efficiencies of the nano-posts to be taken into account simultaneously in the optimization procedures. Therefore, it is used to find geometrical configurations of the nano-posts with suitable phase dispersions and maximized polarization conversion efficiencies. An achromatic metalens has a diameter of 40 μm. The average focal efficiency of this metalens is 53% in the spectrum of 531 nm to 780 nm by simulation, which is higher than the previously reported achromatic metalenses with average efficiencies of 20~36%. The result shows that the introduced method can effectively improve the focal efficiency of the broadband achromatic metalens.
Collapse
Affiliation(s)
- Lijuan Zhang
- Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Sciences, Changchun 130033, China
- University of Chinese Academy of Sciences, Beijing 100039, China
| | - Chengmiao Wang
- Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Sciences, Changchun 130033, China
| | - Yupei Wei
- Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Sciences, Changchun 130033, China
- University of Chinese Academy of Sciences, Beijing 100039, China
| | - Yu Lin
- Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Sciences, Changchun 130033, China
| | - Yeming Han
- Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Sciences, Changchun 130033, China
| | - Yongbo Deng
- Changchun Institute of Optics, Fine Mechanics and Physics (CIOMP), Chinese Academy of Sciences, Changchun 130033, China
| |
Collapse
|
22
|
Khaleghi SSM, Wen D, Cadusch J, Crozier KB. Multicolor detour phase holograms based on an Al plasmonic color filter. OPTICS EXPRESS 2023; 31:2061-2071. [PMID: 36785228 DOI: 10.1364/oe.480812] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/14/2022] [Accepted: 12/12/2022] [Indexed: 06/18/2023]
Abstract
The remarkable advances in nanofabrication that have occurred over the last decade present opportunities for the realization of new types of holograms. In this work, for the first time to the best of our knowledge, a method for phase multicolor holograms based on nanohole arrays is described. The nanoholes are in an aluminum film that is interposed between the glass substrate and a silicon dioxide layer. The nanoholes serve as color filters for blue, green, and red wavelengths and provide the necessary phase distribution via the detour phase method. Our nanohole arrays are optimized to maximize the transmission efficiency of the red, green, and blue channels and to minimize the cross-talk between them. We design two multicolor holograms based on these filters and simulate their performance. The results show good fidelity to the desired holographic images. The proposed structure has the advantages of being very compact, of requiring only a simple fabrication method with one lithography step, and of employing materials (aluminum and silicon dioxide) that are compatible with standard CMOS technology.
Collapse
|
23
|
Ma Z, Jiao Y, Zhang C, Lou J, Zhao P, Zhang B, Wang Y, Yu Y, Sun W, Yan Y, Yang X, Sun L, Wang R, Chang C, Li X, Du X. Identification and quantitative detection of two pathogenic bacteria based on a terahertz metasensor. NANOSCALE 2023; 15:515-521. [PMID: 36519408 DOI: 10.1039/d2nr05038b] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/17/2023]
Abstract
Bacterial infection can cause a series of diseases and play a vital role in medical care. Therefore, early diagnosis of pathogenic bacteria is crucial for effective treatment and the prevention of further infection. However, restricted by the current technology, bacterial detection is usually time-consuming and laborious and the samples need tedious processing even to be tested. Herein, we present a terahertz metasensor based on the coupling of electrical and toroidal dipoles to achieve rapid, non-destructive, label-free identification and highly sensitive quantitative detection of the two most common pathogenic bacteria. The reinforcement of the toroidal dipole significantly boosts the light-matter interactions around the surface of the microstructure, and thus the sensitivity and Q factor of the designed metasensor reach as high as 378 GHz per refractive index unit (RIU) and 21.28, respectively. Combined with the aforementioned advantages, the proposed metasensor successfully identified Escherichia coli and Staphylococcus aureus and quantitatively detected four concentrations with the lowest detectable concentration being ∼104 cfu mL-1 in the experiment. This work naturally enriches the research on THz metasensors based on the interference mechanism and inspires more innovations to facilitate the development of biosensing applications.
Collapse
Affiliation(s)
- Zhaofu Ma
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing 100071, China.
| | - Yanan Jiao
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing 100071, China.
| | - Chiben Zhang
- Air and Missile Defense College, Air Force Engineering University, Xi'an 710051, China
| | - Jing Lou
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing 100071, China.
- Air and Missile Defense College, Air Force Engineering University, Xi'an 710051, China
| | - Pengyue Zhao
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| | - Bin Zhang
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| | - Yujia Wang
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| | - Ying Yu
- Air and Missile Defense College, Air Force Engineering University, Xi'an 710051, China
| | - Wen Sun
- Department of Anesthesiology, The Second Affiliated Hospital, Tianjin University of Traditional Chinese Medicine, Tianjin 300250, China
| | - Yang Yan
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| | - Xingpeng Yang
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| | - Lang Sun
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing 100071, China.
| | - Ride Wang
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing 100071, China.
| | - Chao Chang
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing 100071, China.
| | - Xiru Li
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| | - Xiaohui Du
- Department of General Surgery, First Medical Center, Chinese PLA General Hospital, Beijing 100853, China.
| |
Collapse
|
24
|
Song M, Feng L, Huo P, Liu M, Huang C, Yan F, Lu YQ, Xu T. Versatile full-colour nanopainting enabled by a pixelated plasmonic metasurface. NATURE NANOTECHNOLOGY 2023; 18:71-78. [PMID: 36471110 DOI: 10.1038/s41565-022-01256-4] [Citation(s) in RCA: 20] [Impact Index Per Article: 20.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/27/2022] [Accepted: 10/04/2022] [Indexed: 06/17/2023]
Abstract
The growing interest to develop modern digital displays and colour printing has driven the advancement of colouration technologies with remarkable speed. In particular, metasurface-based structural colouration shows a remarkable high colour saturation, wide gamut palette, chiaroscuro presentation and polarization tunability. However, previous approaches cannot simultaneously achieve all these features. Here, we design and experimentally demonstrate a surface-relief plasmonic metasurface consisting of shallow nanoapertures that enable the independent manipulation of colour hue, saturation and brightness by individually varying the geometric dimensions and orientation of the nanoapertures. We fabricate microscale artworks using a reusable template-stripping technique that features photorealistic and stereoscopic impressions. In addition, through the meticulous arrangement of differently oriented nanoapertures, kaleidoscopic information states can be decrypted by particular combinations of incident and reflected polarized light.
Collapse
Affiliation(s)
- Maowen Song
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China
- Jiangsu Key Laboratory of Artificial Functional Materials, Key Laboratory of Intelligent Optical Sensing and Manipulation, College of Engineering and Applied Sciences, Nanjing University, Nanjing, China
| | - Lei Feng
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China
- Jiangsu Key Laboratory of Artificial Functional Materials, Key Laboratory of Intelligent Optical Sensing and Manipulation, College of Engineering and Applied Sciences, Nanjing University, Nanjing, China
| | - Pengcheng Huo
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China
- Jiangsu Key Laboratory of Artificial Functional Materials, Key Laboratory of Intelligent Optical Sensing and Manipulation, College of Engineering and Applied Sciences, Nanjing University, Nanjing, China
| | - Mingze Liu
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China
- Jiangsu Key Laboratory of Artificial Functional Materials, Key Laboratory of Intelligent Optical Sensing and Manipulation, College of Engineering and Applied Sciences, Nanjing University, Nanjing, China
| | - Chunyu Huang
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China
| | - Feng Yan
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China
- School of Electronic Science and Engineering, Nanjing University, Nanjing, China
| | - Yan-Qing Lu
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China.
- Jiangsu Key Laboratory of Artificial Functional Materials, Key Laboratory of Intelligent Optical Sensing and Manipulation, College of Engineering and Applied Sciences, Nanjing University, Nanjing, China.
| | - Ting Xu
- National Laboratory of Solid-State Microstructures and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, China.
- Jiangsu Key Laboratory of Artificial Functional Materials, Key Laboratory of Intelligent Optical Sensing and Manipulation, College of Engineering and Applied Sciences, Nanjing University, Nanjing, China.
| |
Collapse
|
25
|
Akbari-Chelaresi H, Salami P, Yousefi L. Far-field sub-wavelength imaging using high-order dielectric continuous metasurfaces. OPTICS EXPRESS 2022; 30:39025-39039. [PMID: 36258453 DOI: 10.1364/oe.470221] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/13/2022] [Accepted: 08/26/2022] [Indexed: 05/20/2023]
Abstract
Due to the wave nature of light, the resolution achieved in conventional imaging systems is limited to around half of the wavelength. The reason behind this limitation, called diffraction limit, is that part of the information of the object carried by the evanescent waves scattered from an abject. Although retrieving information from propagating waves is not difficult in the far-field region, it is very challenging in the case of evanescent waves, which decay exponentially as travel and lose their power in the far-field region. In this paper, we design a high-order continuous dielectric metasurface to convert evanescent waves into propagating modes and subsequently to reconstruct super-resolution images in the far field. The designed metasurface is characterized and its performance for sub-wavelength imaging is verified using full wave numerical simulations. Simulation results show that the designed continuous high-order metasurface can convert a large group of evanescent waves into propagating ones. The designed metasurface is then used to reconstruct the image of objects with sub-wavelength features, and an image with the resolution of λ/5.5 is achieved.
Collapse
|
26
|
Kanyang R, Fang C, Yang Q, Shao Y, Han G, Liu Y, Hao Y. Electro-Optical Modulation in High Q Metasurface Enhanced with Liquid Crystal Integration. NANOMATERIALS (BASEL, SWITZERLAND) 2022; 12:nano12183179. [PMID: 36144966 PMCID: PMC9506199 DOI: 10.3390/nano12183179] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/16/2022] [Revised: 09/09/2022] [Accepted: 09/11/2022] [Indexed: 05/28/2023]
Abstract
Electro-optical tuning metasurfaces are particularly attractive since they open up routes for dynamic reconfiguration. The electro-optic (EO) modulation strength essentially depends on the sensitivity to the EO-induced refractive index changes. In this paper, lithium niobate (LiNbO3) metasurfaces integrated with liquid crystals (LCs) are theoretically investigated. Cylinder arrays are proposed to support quasi-bound states in the continuum (quasi-BICs). The quasi-BIC resonances can significantly enhance the lifetime of photons and the local field, contributing to the EO-refractive index changes. By integrating metasurfaces with LCs, the combined influence of the LC reorientation and the Pockels electro-optic effect of LiNbO3 is leveraged to tune the transmitted wavelength and phase spectrum around the quasi-BIC wavelength, resulting in an outstanding tuning sensitivity up to Δλ/ΔV ≈ 0.6 nm/V and relieving the need of high voltage. Furthermore, the proposed structure can alleviate the negative influence of sidewall tilt on device performance. The results presented in this work can foster wide application and prospects for the implementation of tunable displays, light detection and ranging (LiDAR), and spatial light modulators (SLMs).
Collapse
Affiliation(s)
- Ruoying Kanyang
- Emerging Device and Chip Laboratory, Hangzhou Institute of Technology, Xidian University, Hangzhou 311200, China
- Wide Bandgap Semiconductor Technology Disciplines State Key Laboratory, School of Microelectronics, Xidian University, Xi’an 710071, China
| | - Cizhe Fang
- Emerging Device and Chip Laboratory, Hangzhou Institute of Technology, Xidian University, Hangzhou 311200, China
- Wide Bandgap Semiconductor Technology Disciplines State Key Laboratory, School of Microelectronics, Xidian University, Xi’an 710071, China
| | - Qiyu Yang
- Wide Bandgap Semiconductor Technology Disciplines State Key Laboratory, School of Microelectronics, Xidian University, Xi’an 710071, China
| | - Yao Shao
- Shanghai Energy Internet Research Institute of State, Grid 251 Libing Road, Pudong New Area, Shanghai 201210, China
| | - Genquan Han
- Emerging Device and Chip Laboratory, Hangzhou Institute of Technology, Xidian University, Hangzhou 311200, China
- Wide Bandgap Semiconductor Technology Disciplines State Key Laboratory, School of Microelectronics, Xidian University, Xi’an 710071, China
- The Research Center for Intelligent Chips and Devices—Zhejiang Lab, Hangzhou 311121, China
| | - Yan Liu
- Emerging Device and Chip Laboratory, Hangzhou Institute of Technology, Xidian University, Hangzhou 311200, China
- Wide Bandgap Semiconductor Technology Disciplines State Key Laboratory, School of Microelectronics, Xidian University, Xi’an 710071, China
| | - Yue Hao
- Wide Bandgap Semiconductor Technology Disciplines State Key Laboratory, School of Microelectronics, Xidian University, Xi’an 710071, China
| |
Collapse
|
27
|
Archetti A, Lin RJ, Restori N, Kiani F, Tsoulos TV, Tagliabue G. Thermally reconfigurable metalens. NANOPHOTONICS 2022; 11:3969-3980. [PMID: 36059378 PMCID: PMC9394514 DOI: 10.1515/nanoph-2022-0147] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/15/2022] [Accepted: 05/17/2022] [Indexed: 05/05/2023]
Abstract
Reconfigurable metalenses are compact optical components composed by arrays of meta-atoms that offer unique opportunities for advanced optical systems, from microscopy to augmented reality platforms. Although poorly explored in the context of reconfigurable metalenses, thermo-optical effects in resonant silicon nanoresonators have recently emerged as a viable strategy to realize tunable meta-atoms. In this work, we report the proof-of-concept design of an ultrathin (300 nm thick) and thermo-optically reconfigurable silicon metalens operating at a fixed, visible wavelength (632 nm). Importantly, we demonstrate continuous, linear modulation of the focal-length up to 21% (from 165 μm at 20 °C to 135 μm at 260 °C). Operating under right-circularly polarized light, our metalens exhibits an average conversion efficiency of 26%, close to mechanically modulated devices, and has a diffraction-limited performance. Overall, we envision that, combined with machine-learning algorithms for further optimization of the meta-atoms, thermally reconfigurable metalenses with improved performance will be possible. Also, the generality of this approach could offer inspiration for the realization of active metasurfaces with other emerging materials within field of thermo-nanophotonics.
Collapse
Affiliation(s)
- Anna Archetti
- Laboratory of Nanoscience for Energy Technologies (LNET), STI, École Polytechnique Fédérale de Lausanne (EPFL), Lausanne1015, Switzerland
| | - Ren-Jie Lin
- Laboratory of Nanoscience for Energy Technologies (LNET), STI, École Polytechnique Fédérale de Lausanne (EPFL), Lausanne1015, Switzerland
| | - Nathanaël Restori
- Laboratory of Nanoscience for Energy Technologies (LNET), STI, École Polytechnique Fédérale de Lausanne (EPFL), Lausanne1015, Switzerland
| | - Fatemeh Kiani
- Laboratory of Nanoscience for Energy Technologies (LNET), STI, École Polytechnique Fédérale de Lausanne (EPFL), Lausanne1015, Switzerland
| | - Ted V. Tsoulos
- Laboratory of Nanoscience for Energy Technologies (LNET), STI, École Polytechnique Fédérale de Lausanne (EPFL), Lausanne1015, Switzerland
| | - Giulia Tagliabue
- Laboratory of Nanoscience for Energy Technologies (LNET), STI, École Polytechnique Fédérale de Lausanne (EPFL), Lausanne1015, Switzerland
| |
Collapse
|
28
|
Damgaard-Carstensen C, Thomaschewski M, Bozhevolnyi SI. Electro-optic metasurface-based free-space modulators. NANOSCALE 2022; 14:11407-11414. [PMID: 35900044 DOI: 10.1039/d2nr02979k] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/15/2023]
Abstract
Research in optical metasurfaces has explosively grown in recent years, primarily due to their ability of exercising complete control over the transmitted and reflected fields. Application prospects in many emerging technologies require this control to become dynamic, so that the metasurface response could be tuned with external stimuli. In this work, electrically tunable optical metasurfaces operating in reflection as optical free-space modulators are demonstrated. The intensity modulation is achieved by exploiting the electro-optic Pockels effect and tuning the Fabry-Perot resonance in a 320 nm-thick lithium niobate (LN) film sandwiched between a continuous thick gold film and an array of gold nanostripes, serving also as control electrodes. The proposed compact (<1000 μm2) modulators operate in the wavelength range of 900-1000 nm, featuring a maximum intensity modulation depth of ∼20% at the driving voltage of ± 10 V within the bandwidth of 8.0 MHz (with the potential bandwidth of ∼25 GHz). By arranging a 2 × 2 array of individually addressable modulators, space-variant control of light reflection is demonstrated, therefore opening a way towards the realization of inertia-free, ultrafast, and robust spatial light modulators based on tunable LN flat optics components.
Collapse
Affiliation(s)
| | - Martin Thomaschewski
- Centre for Nano Optics, University of Southern Denmark, Campusvej 55, DK-5230 Odense M, Denmark.
| | - Sergey I Bozhevolnyi
- Centre for Nano Optics, University of Southern Denmark, Campusvej 55, DK-5230 Odense M, Denmark.
| |
Collapse
|
29
|
Javed I, Kim J, Naveed MA, Oh DK, Jeon D, Kim I, Zubair M, Massoud Y, Mehmood MQ, Rho J. Broad-Band Polarization-Insensitive Metasurface Holography with a Single-Phase Map. ACS APPLIED MATERIALS & INTERFACES 2022; 14:36019-36026. [PMID: 35912417 DOI: 10.1021/acsami.2c07960] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/21/2023]
Abstract
The remarkable potential of metasurface holography promises revolutionary advancements for imaging, chip-integrated augmented/virtual reality (AR/VR) technology, and flat optical displays. The choice of constituent element geometry constrains many potential applications purveyed through polarization-independent optical response. The limited capabilities and degree of freedoms in commonly used meta-atoms restrict the design flexibility to break the conventional trade-off between polarization-insensitivity and bandwidth. Here, we propose a geometric phase-enabled novel design strategy to break this conventional trade-off. The proposed strategy ensures the realization of broad-band polarization-insensitivity through a simplified design procedure. An identical output wavefront manipulation is achieved by adjusting the phase delay freedom of geometric phase engineering under different incident polarization conditions. For proof of concept, a metahologram device is fabricated by an optimized complementary metal-oxide-semiconductor (CMOS)-compatible material of hydrogenated amorphous silicon (a-Si:H). This metahologram device reproduces the required hologram with high image fidelity and efficiency under different polarization scenarios of white light incidence. Due to the simple design strategy, low computational cost, and easy fabrication, the proposed technique can be an excellent candidate for realizing polarization-insensitive metahologram devices.
Collapse
Affiliation(s)
- Isma Javed
- MicroNano Lab, Electrical Engineering Department, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan
| | - Joohoon Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Muhammad Ashar Naveed
- MicroNano Lab, Electrical Engineering Department, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan
| | - Dong Kyo Oh
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Dongmin Jeon
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Inki Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
- Department of Biophysics, Institute of Quantum Biophysics, Sungkyunkwan University, Suwon 16419, Republic of Korea
- Department of Intelligent Precision Healthcare Convergence, Sungkyunkwan University, Suwon 16419, Republic of Korea
| | - Muhammad Zubair
- MicroNano Lab, Electrical Engineering Department, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan
| | - Yehia Massoud
- Innovative Technologies Laboratories (ITL), King Abdullah University of Science and Technology (KAUST), Thuwal 23955, Saudi Arabia
| | - Muhammad Qasim Mehmood
- MicroNano Lab, Electrical Engineering Department, Information Technology University (ITU) of the Punjab, Lahore 54600, Pakistan
| | - Junsuk Rho
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
- POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang 37673, Republic of Korea
- National Institute of Nanomaterials Technology (NINT), Pohang 37673, Republic of Korea
| |
Collapse
|
30
|
Malek SC, Overvig AC, Alù A, Yu N. Multifunctional resonant wavefront-shaping meta-optics based on multilayer and multi-perturbation nonlocal metasurfaces. LIGHT, SCIENCE & APPLICATIONS 2022; 11:246. [PMID: 35922413 PMCID: PMC9349264 DOI: 10.1038/s41377-022-00905-6] [Citation(s) in RCA: 15] [Impact Index Per Article: 7.5] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/13/2022] [Revised: 06/11/2022] [Accepted: 06/20/2022] [Indexed: 05/22/2023]
Abstract
Photonic devices rarely provide both elaborate spatial control and sharp spectral control over an incoming wavefront. In optical metasurfaces, for example, the localized modes of individual meta-units govern the wavefront shape over a broad bandwidth, while nonlocal lattice modes extended over many unit cells support high quality-factor resonances. Here, we experimentally demonstrate nonlocal dielectric metasurfaces in the near-infrared that offer both spatial and spectral control of light, realizing metalenses focusing light exclusively over a narrowband resonance while leaving off-resonant frequencies unaffected. Our devices attain this functionality by supporting a quasi-bound state in the continuum encoded with a spatially varying geometric phase. We leverage this capability to experimentally realize a versatile platform for multispectral wavefront shaping where a stack of metasurfaces, each supporting multiple independently controlled quasi-bound states in the continuum, molds the optical wavefront distinctively at multiple wavelengths and yet stay transparent over the rest of the spectrum. Such a platform is scalable to the visible for applications in augmented reality and transparent displays.
Collapse
Affiliation(s)
- Stephanie C Malek
- Department of Applied Physics and Applied Mathematics, Columbia University, New York, NY, 10027, USA
| | - Adam C Overvig
- Department of Applied Physics and Applied Mathematics, Columbia University, New York, NY, 10027, USA
- Photonics Initiative, Advanced Science Research Center, City University of New York, New York, NY, 10031, USA
| | - Andrea Alù
- Photonics Initiative, Advanced Science Research Center, City University of New York, New York, NY, 10031, USA
- Physics Program, Graduate Center, City University of New York, New York, NY, 10016, USA
| | - Nanfang Yu
- Department of Applied Physics and Applied Mathematics, Columbia University, New York, NY, 10027, USA.
| |
Collapse
|
31
|
Li J, Fan H, Ye H, Wu T, Sun Y, Wang X, Liu Y. Design of Multifunctional Tunable Metasurface Assisted by Elastic Substrate. NANOMATERIALS 2022; 12:nano12142387. [PMID: 35889611 PMCID: PMC9315715 DOI: 10.3390/nano12142387] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 06/18/2022] [Revised: 07/09/2022] [Accepted: 07/11/2022] [Indexed: 02/04/2023]
Abstract
Metasurfaces with both multifunctionality and tunability hold great application potential in next-generation optical devices. In this paper, we propose a stretchable metasurface composed of arrays of identical dielectric rectangular resonators embedded in the polydimethylsiloxane (PDMS) substrate. It is shown that the metasurface possesses three functions at the operating wavelength of 532 nm. The switching of functions can be implemented by changing the period Px of the metasurface, induced by stretching the PDMS substrate along the x-direction. When the period Px is less than the operating wavelength of 532 nm, the behavior of metasurface can switch between transmissive window and reflective mirror. When the period Px of the metasurface varies from 532 nm to 700 nm, the metasurface act as a dynamic equal-power beam splitter with conversion efficiency higher than 90%, and the corresponding splitting angle can be adjusted from 90° to around 49.5°. Moreover, we achieve the switching of transmissive window/reflective mirror/split-ratio-variable splitter based on the metasurface consisting of arrays of identical L-shaped resonators embedded in the PDMS substrate.
Collapse
Affiliation(s)
- Jing Li
- State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876, China; (J.L.); (H.F.); (Y.S.); (X.W.)
| | - Hongjie Fan
- State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876, China; (J.L.); (H.F.); (Y.S.); (X.W.)
| | - Han Ye
- State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876, China; (J.L.); (H.F.); (Y.S.); (X.W.)
- Correspondence: (H.Y.); (Y.L.)
| | - Tiesheng Wu
- College of Information and Communication Engineering, Guilin University of Electronic Technology, Guilin 541004, China;
| | - Yuhang Sun
- State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876, China; (J.L.); (H.F.); (Y.S.); (X.W.)
| | - Xueyu Wang
- State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876, China; (J.L.); (H.F.); (Y.S.); (X.W.)
| | - Yumin Liu
- State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876, China; (J.L.); (H.F.); (Y.S.); (X.W.)
- Correspondence: (H.Y.); (Y.L.)
| |
Collapse
|
32
|
Ullah N, Zhao R, Huang L. Recent Advancement in Optical Metasurface: Fundament to Application. MICROMACHINES 2022; 13:1025. [PMID: 35888842 PMCID: PMC9322754 DOI: 10.3390/mi13071025] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 05/31/2022] [Revised: 06/21/2022] [Accepted: 06/25/2022] [Indexed: 12/01/2022]
Abstract
Metasurfaces have gained growing interest in recent years due to their simplicity in manufacturing and lower insertion losses. Meanwhile, they can provide unprecedented control over the spatial distribution of transmitted and reflected optical fields in a compact form. The metasurfaces are a kind of planar array of resonant subwavelength components that, depending on the intended optical wavefronts to be sculpted, can be strictly periodic or quasi-periodic, or even aperiodic. For instance, gradient metasurfaces, a subtype of metasurfaces, are designed to exhibit spatially changing optical responses, which result in spatially varying amplitudes of scattered fields and the associated polarization of these fields. This paper starts off by presenting concepts of anomalous reflection and refraction, followed by a brief discussion on the Pancharatanm-Berry Phase (PB) and Huygens' metasurfaces. As an introduction to wavefront manipulation, we next present their key applications. These include planar metalens, cascaded meta-systems, tunable metasurfaces, spectrometer retroreflectors, vortex beams, and holography. The review concludes with a summary, preceded by a perspective outlining our expectations for potential future research work and applications.
Collapse
Affiliation(s)
- Naqeeb Ullah
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing 100081, China; (N.U.); (R.Z.)
- Department of Electronic Engineering, Balochistan University of Information Technology, Engineering and Management Sciences, Quetta 87300, Pakistan
| | - Ruizhe Zhao
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing 100081, China; (N.U.); (R.Z.)
| | - Lingling Huang
- Beijing Engineering Research Center of Mixed Reality and Advanced Display, School of Optics and Photonics, Beijing Institute of Technology, Beijing 100081, China; (N.U.); (R.Z.)
| |
Collapse
|
33
|
Abstract
Recent years have witnessed promising artificial intelligence (AI) applications in many disciplines, including optics, engineering, medicine, economics, and education. In particular, the synergy of AI and meta-optics has greatly benefited both fields. Meta-optics are advanced flat optics with novel functions and light-manipulation abilities. The optical properties can be engineered with a unique design to meet various optical demands. This review offers comprehensive coverage of meta-optics and artificial intelligence in synergy. After providing an overview of AI and meta-optics, we categorize and discuss the recent developments integrated by these two topics, namely AI for meta-optics and meta-optics for AI. The former describes how to apply AI to the research of meta-optics for design, simulation, optical information analysis, and application. The latter reports the development of the optical Al system and computation via meta-optics. This review will also provide an in-depth discussion of the challenges of this interdisciplinary field and indicate future directions. We expect that this review will inspire researchers in these fields and benefit the next generation of intelligent optical device design.
Collapse
Affiliation(s)
- Mu Ku Chen
- Department of Electrical Engineering, City University of Hong Kong, Kowloon, Hong Kong 999077.,Centre for Biosystems, Neuroscience, and Nanotechnology, City University of Hong Kong, Kowloon, Hong Kong 999077.,The State Key Laboratory of Terahertz and Millimeter Waves, City University of Hong Kong, Kowloon, Hong Kong 999077
| | - Xiaoyuan Liu
- Department of Electrical Engineering, City University of Hong Kong, Kowloon, Hong Kong 999077
| | - Yanni Sun
- Department of Electrical Engineering, City University of Hong Kong, Kowloon, Hong Kong 999077
| | - Din Ping Tsai
- Department of Electrical Engineering, City University of Hong Kong, Kowloon, Hong Kong 999077.,Centre for Biosystems, Neuroscience, and Nanotechnology, City University of Hong Kong, Kowloon, Hong Kong 999077.,The State Key Laboratory of Terahertz and Millimeter Waves, City University of Hong Kong, Kowloon, Hong Kong 999077
| |
Collapse
|
34
|
Hsu WL, Chen YC, Yeh SP, Zeng QC, Huang YW, Wang CM. Review of Metasurfaces and Metadevices: Advantages of Different Materials and Fabrications. NANOMATERIALS 2022; 12:nano12121973. [PMID: 35745310 PMCID: PMC9231017 DOI: 10.3390/nano12121973] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 04/24/2022] [Revised: 05/29/2022] [Accepted: 06/03/2022] [Indexed: 01/27/2023]
Abstract
Flat optics, metasurfaces, metalenses, and related materials promise novel on-demand light modulation within ultrathin layers at wavelength scale, enabling a plethora of next-generation optical devices, also known as metadevices. Metadevices designed with different materials have been proposed and demonstrated for different applications, and the mass production of metadevices is necessary for metadevices to enter the consumer electronics market. However, metadevice manufacturing processes are mainly based on electron beam lithography, which exhibits low productivity and high costs for mass production. Therefore, processes compatible with standard complementary metal–oxide–semiconductor manufacturing techniques that feature high productivity, such as i-line stepper and nanoimprint lithography, have received considerable attention. This paper provides a review of current metasurfaces and metadevices with a focus on materials and manufacturing processes. We also provide an analysis of the relationship between the aspect ratio and efficiency of different materials.
Collapse
Affiliation(s)
- Wei-Lun Hsu
- Department of Optics and Photonics, National Central University, Taoyuan 32001, Taiwan; (W.-L.H.); (Y.-C.C.); (S.P.Y.); (Q.-C.Z.)
| | - Yen-Chun Chen
- Department of Optics and Photonics, National Central University, Taoyuan 32001, Taiwan; (W.-L.H.); (Y.-C.C.); (S.P.Y.); (Q.-C.Z.)
| | - Shang Ping Yeh
- Department of Optics and Photonics, National Central University, Taoyuan 32001, Taiwan; (W.-L.H.); (Y.-C.C.); (S.P.Y.); (Q.-C.Z.)
| | - Qiu-Chun Zeng
- Department of Optics and Photonics, National Central University, Taoyuan 32001, Taiwan; (W.-L.H.); (Y.-C.C.); (S.P.Y.); (Q.-C.Z.)
| | - Yao-Wei Huang
- Department of Photonics, National Yang Ming Chiao Tung University, Hsinchu 30010, Taiwan
- Correspondence: (Y.-W.H.); (C.-M.W.)
| | - Chih-Ming Wang
- Department of Optics and Photonics, National Central University, Taoyuan 32001, Taiwan; (W.-L.H.); (Y.-C.C.); (S.P.Y.); (Q.-C.Z.)
- Correspondence: (Y.-W.H.); (C.-M.W.)
| |
Collapse
|
35
|
Abstract
Structural color has been regarded as an ideal alternative to pigments because of the advantages of environmental friendliness, resistance to fading, and dynamic regulation. Responsive structural color can give real-time visible feedback to external stimuli and thus has great prospects in many applications, such as displays, sensing, anticounterfeiting, information storage, and healthcare monitoring. In this Perspective, we elucidate basic concepts, controllable fabrications, and promising applications of responsive structural colors. In particular, we systematically summarize the general regulation mode of all kinds of responsive structural color systems. First, we introduce the basic chromogenic structures as well as the regulation modes of responsive structural color. Second, we present the fabrication methods of patterned structural color. Then, the promising applications of responsive structural color systems are highlighted in detail. Finally, we present the existing challenges and future perspectives on responsive structural colors.
Collapse
Affiliation(s)
- Xiaoyu Hou
- Key Laboratory of Green Printing, CAS Research/Education Center for Excellence in Molecular Sciences, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190, P.R. China
- University of Chinese Academy of Sciences, 100049 Beijing, P.R. China
| | - Fuzhen Li
- Key Laboratory of Green Printing, CAS Research/Education Center for Excellence in Molecular Sciences, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190, P.R. China
- University of Chinese Academy of Sciences, 100049 Beijing, P.R. China
| | - Yanlin Song
- Key Laboratory of Green Printing, CAS Research/Education Center for Excellence in Molecular Sciences, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190, P.R. China
- University of Chinese Academy of Sciences, 100049 Beijing, P.R. China
| | - Mingzhu Li
- Key Laboratory of Green Printing, CAS Research/Education Center for Excellence in Molecular Sciences, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190, P.R. China
- University of Chinese Academy of Sciences, 100049 Beijing, P.R. China
- Key Laboratory of Materials Processing and Mold of the Ministry of Education, Zhengzhou University, Zhengzhou 450002, P.R. China
| |
Collapse
|
36
|
Ray D, Wang HC, Kim J, Santschi C, Martin OJF. A Low-Temperature Annealing Method for Alloy Nanostructures and Metasurfaces: Unlocking a Novel Degree of Freedom. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2108225. [PMID: 35167722 DOI: 10.1002/adma.202108225] [Citation(s) in RCA: 7] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/13/2021] [Revised: 02/02/2022] [Indexed: 06/14/2023]
Abstract
The material and exact shape of a nanostructure determine its optical response, which is especially strong for plasmonic metals. Unfortunately, only a few plasmonic metals are available, which limits the spectral range where these strong optical effects can be utilized. Alloying different plasmonic metals can overcome this limitation, at the expense of using a high-temperature alloying process, which adversely destroys the nanostructure shape. Here, a low-temperature alloying process is developed where the sample is heated at only 300 °C for 8 h followed by 30 min at 450 °C and Au-Ag nanostructures with a broad diversity of shapes, aspect ratios, and stoichiometries are fabricated. Energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy analyses confirm the homogeneous alloying through the entire sample. Varying the alloy stoichiometry tunes the optical response and controls spectral features, such as Fano resonances. Binary metasurfaces that combine nanostructures with different stoichiometries are fabricated using multiple-step electron-beam lithography, and their optical function as a hologram or a Fresnel zone plate is demonstrated at the visible wavelength of λ = 532 nm. This low-temperature annealing technique provides a versatile and cost-effective way of fabricating complex Au-Ag nanostructures with arbitrary stoichiometry.
Collapse
Affiliation(s)
- Debdatta Ray
- Nanophotonics and Metrology Laboratory, Swiss Federal Institute of Technology, Lausanne (EPFL), Lausanne, 1015, Switzerland
| | - Hsiang-Chu Wang
- Nanophotonics and Metrology Laboratory, Swiss Federal Institute of Technology, Lausanne (EPFL), Lausanne, 1015, Switzerland
| | - Jeonghyeon Kim
- Nanophotonics and Metrology Laboratory, Swiss Federal Institute of Technology, Lausanne (EPFL), Lausanne, 1015, Switzerland
| | - Christian Santschi
- Nanophotonics and Metrology Laboratory, Swiss Federal Institute of Technology, Lausanne (EPFL), Lausanne, 1015, Switzerland
| | - Olivier J F Martin
- Nanophotonics and Metrology Laboratory, Swiss Federal Institute of Technology, Lausanne (EPFL), Lausanne, 1015, Switzerland
| |
Collapse
|
37
|
Ma W, Xu Y, Xiong B, Deng L, Peng RW, Wang M, Liu Y. Pushing the Limits of Functionality-Multiplexing Capability in Metasurface Design Based on Statistical Machine Learning. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2110022. [PMID: 35167138 DOI: 10.1002/adma.202110022] [Citation(s) in RCA: 29] [Impact Index Per Article: 14.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/08/2021] [Revised: 02/06/2022] [Indexed: 06/14/2023]
Abstract
As 2D metamaterials, metasurfaces provide an unprecedented means to manipulate light with the ability to multiplex different functionalities in a single planar device. Currently, most pursuits of multifunctional metasurfaces resort to empirically accommodating more functionalities at the cost of increasing structural complexity, with little effort to investigate the intrinsic restrictions of given meta-atoms and thus the ultimate limits in the design. In this work, it is proposed to embed machine-learning models in both gradient-based and nongradient optimization loops for the automatic implementation of multifunctional metasurfaces. Fundamentally different from the traditional two-step approach that separates phase retrieval and meta-atom structural design, the proposed end-to-end framework facilitates full exploitation of the prescribed design space and pushes the multifunctional design capacity to its physical limit. With a single-layer structure that can be readily fabricated, metasurface focusing lenses and holograms are experimentally demonstrated in the near-infrared region. They show up to eight controllable responses subjected to different combinations of working frequencies and linear polarization states, which are unachievable by the conventional physics-guided approaches. These results manifest the superior capability of the data-driven scheme for photonic design, and will accelerate the development of complex devices and systems for optical display, communication, and computing.
Collapse
Affiliation(s)
- Wei Ma
- State Key Laboratory of Modern Optical Instrumentation, College of Information Science and Electronic Engineering, Zhejiang University, Hangzhou, 310027, China
| | - Yihao Xu
- Department of Mechanical and Industrial Engineering, Northeastern University, Boston, MA, 02115, USA
| | - Bo Xiong
- National Laboratory of Solid State Microstructures, School of Physics, and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, 210093, China
| | - Lin Deng
- Department of Electrical and Computer Engineering, Northeastern University, Boston, MA, 02115, USA
| | - Ru-Wen Peng
- National Laboratory of Solid State Microstructures, School of Physics, and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, 210093, China
| | - Mu Wang
- National Laboratory of Solid State Microstructures, School of Physics, and Collaborative Innovation Center of Advanced Microstructures, Nanjing University, Nanjing, 210093, China
| | - Yongmin Liu
- Department of Mechanical and Industrial Engineering, Northeastern University, Boston, MA, 02115, USA
- Department of Electrical and Computer Engineering, Northeastern University, Boston, MA, 02115, USA
| |
Collapse
|
38
|
Kim G, Kim S, Kim H, Lee J, Badloe T, Rho J. Metasurface-empowered spectral and spatial light modulation for disruptive holographic displays. NANOSCALE 2022; 14:4380-4410. [PMID: 35266481 DOI: 10.1039/d1nr07909c] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/14/2023]
Abstract
The holographic display, one of the most realistic ways to reconstruct optical images in three-dimensional (3D) space, has gained a lot of attention as a next-generation display platform for providing deeper immersive experiences to users. So far, diffractive optical elements (DOEs) and spatial light modulators (SLMs) have been used to generate holographic images by modulating electromagnetic waves at each pixel. However, such architectures suffer from limitations in terms of having a resolution of only a few microns and the bulkiness of the entire optical system. In this review, we describe novel metasurfaces-based nanophotonic platforms that have shown exceptional control of electromagnetic waves at the subwavelength scale as promising candidates to overcome existing restrictions, while realizing flat optical devices. After introducing the fundamentals of metasurfaces in terms of spatial and spectral wavefront modulation, we present a variety of multiplexing approaches for high-capacity and full-color metaholograms exploiting the multiple properties of light as an information carrier. We then review tunable metaholograms using active materials modulated by several external stimuli. Afterward, we discuss the integration of metasurfaces with other optical elements required for future 3D display platforms in augmented/virtual reality (AR/VR) displays such as lenses, beam splitters, diffusers, and eye-tracking sensors. Finally, we address the challenges of conventional nanofabrication methods and introduce scalable preparation techniques that can be applied to metasurface-based nanophotonic technologies towards commercially and ergonomically viable future holographic displays.
Collapse
Affiliation(s)
- Gyeongtae Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Seokwoo Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Hongyoon Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Jihae Lee
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Trevon Badloe
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
| | - Junsuk Rho
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
- POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang 37673, Republic of Korea
| |
Collapse
|
39
|
Yang J, Gurung S, Bej S, Ni P, Howard Lee HW. Active optical metasurfaces: comprehensive review on physics, mechanisms, and prospective applications. REPORTS ON PROGRESS IN PHYSICS. PHYSICAL SOCIETY (GREAT BRITAIN) 2022; 85:036101. [PMID: 35244609 DOI: 10.1088/1361-6633/ac2aaf] [Citation(s) in RCA: 25] [Impact Index Per Article: 12.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/30/2020] [Accepted: 09/28/2021] [Indexed: 06/14/2023]
Abstract
Optical metasurfaces with subwavelength thickness hold considerable promise for future advances in fundamental optics and novel optical applications due to their unprecedented ability to control the phase, amplitude, and polarization of transmitted, reflected, and diffracted light. Introducing active functionalities to optical metasurfaces is an essential step to the development of next-generation flat optical components and devices. During the last few years, many attempts have been made to develop tunable optical metasurfaces with dynamic control of optical properties (e.g., amplitude, phase, polarization, spatial/spectral/temporal responses) and early-stage device functions (e.g., beam steering, tunable focusing, tunable color filters/absorber, dynamic hologram, etc) based on a variety of novel active materials and tunable mechanisms. These recently-developed active metasurfaces show significant promise for practical applications, but significant challenges still remain. In this review, a comprehensive overview of recently-reported tunable metasurfaces is provided which focuses on the ten major tunable metasurface mechanisms. For each type of mechanism, the performance metrics on the reported tunable metasurface are outlined, and the capabilities/limitations of each mechanism and its potential for various photonic applications are compared and summarized. This review concludes with discussion of several prospective applications, emerging technologies, and research directions based on the use of tunable optical metasurfaces. We anticipate significant new advances when the tunable mechanisms are further developed in the coming years.
Collapse
Affiliation(s)
- Jingyi Yang
- Department of Physics & Astronomy, University of California, Irvine, CA 92697, United States of America
- Department of Physics, Baylor University, Waco, TX 76798, United States of America
| | - Sudip Gurung
- Department of Physics & Astronomy, University of California, Irvine, CA 92697, United States of America
- Department of Physics, Baylor University, Waco, TX 76798, United States of America
| | - Subhajit Bej
- Department of Physics, Baylor University, Waco, TX 76798, United States of America
| | - Peinan Ni
- Department of Physics, Baylor University, Waco, TX 76798, United States of America
| | - Ho Wai Howard Lee
- Department of Physics & Astronomy, University of California, Irvine, CA 92697, United States of America
- Department of Physics, Baylor University, Waco, TX 76798, United States of America
| |
Collapse
|
40
|
Wang L, Wang T, Yan R, Yue X, Wang H, Wang Y, Zhang J. Tunable structural colors generated by hybrid Si 3N 4 and Al metasurfaces. OPTICS EXPRESS 2022; 30:7299-7307. [PMID: 35299494 DOI: 10.1364/oe.451040] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/10/2021] [Accepted: 02/02/2022] [Indexed: 06/14/2023]
Abstract
Metasurfaces with the capability of spectrum manipulation at subwavelength can generate structural colors. However, their practical applications in dynamic displays are limited because their optical performance is immutable after the fabrication of the metasurfaces. In this study, we demonstrate a color-tunable metasurface using numerical analysis. Moreover, we select a low-refractive-index dielectric material, Si3N4, which leaks the electric field to its surroundings. We investigate the potencial of these metasurfaces by simulations to achieve color-tuneable devices with encrypted watermarks. This modulation of colors can be applied to encrypted watermarks, anti-counterfeiting, and dynamic displays.
Collapse
|
41
|
Qu J, Luo H, Yu C. Dual-Wavelength Polarization-Dependent Bifocal Metalens for Achromatic Optical Imaging Based on Holographic Principle. SENSORS 2022; 22:s22051889. [PMID: 35271036 PMCID: PMC8915052 DOI: 10.3390/s22051889] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 01/14/2022] [Revised: 02/20/2022] [Accepted: 02/24/2022] [Indexed: 11/16/2022]
Abstract
Recently, ultrathin metalenses have attracted dramatically growing interest in optical imaging systems due to the flexible control of light at the nanoscale. In this paper, we propose a dual-wavelength achromatic metalens that will generate one or two foci according to the polarization of the incident. Based on geometric phase modulation, two unit cells are attentively selected for efficient operation at distinct wavelengths. By patterning them to two divided sections of the metalens structure plane, the dual-wavelength achromatic focusing effect with the same focal length is realized. In addition, the holographic concept is adopted for polarization-dependent bifocal generation, in which the objective wave is originated from two foci that are respectively formed by two orthogonal polarization states of circularly polarized light, namely Left-handed circularly polarized (LCP) light and Right-handed circularly polarized (RCP) light. The incident light is considered as the reference light. The achromatic focusing and polarization-dependent bifocusing are numerically verified through simulations. The proposed design opens the path for the combination of multi-wavelength imaging and chiral imaging, which may find potential applications, such as achromatic optical devices and polarization-controlled biomedical molecular imaging systems.
Collapse
Affiliation(s)
- Jiaqi Qu
- The Photonics Research Center, Department of Electronic and Information Engineering, The Hong Kong Polytechnic University, Hong Kong 999077, China; (J.Q.); (H.L.)
| | - Huaijian Luo
- The Photonics Research Center, Department of Electronic and Information Engineering, The Hong Kong Polytechnic University, Hong Kong 999077, China; (J.Q.); (H.L.)
| | - Changyuan Yu
- The Photonics Research Center, Department of Electronic and Information Engineering, The Hong Kong Polytechnic University, Hong Kong 999077, China; (J.Q.); (H.L.)
- The Hong Kong Polytechnic University Shen Zhen Research Institute, Shenzhen 518057, China
- Correspondence:
| |
Collapse
|
42
|
Optical Fiber-Integrated Metasurfaces: An Emerging Platform for Multiple Optical Applications. NANOMATERIALS 2022; 12:nano12050793. [PMID: 35269280 PMCID: PMC8912696 DOI: 10.3390/nano12050793] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 12/31/2021] [Revised: 02/08/2022] [Accepted: 02/23/2022] [Indexed: 11/25/2022]
Abstract
The advent of metasurface technology has revolutionized the field of optics and photonics in recent years due to its capability of engineering optical wavefronts with well-patterned nanostructures at subwavelength scale. Meanwhile, inspired and benefited from the tremendous success of the “lab-on-fiber” concept, the integration of metasurface with optical fibers has drawn particular interest in the last decade, which establishes a novel technological platform towards the development of “all-in-fiber” metasurface-based devices. Thereby, this review aims to present and summarize the optical fiber-integrated metasurfaces with the current state of the art. The application scenarios of the optical fiber metasurface-based devices are well classified and discussed accordingly, with a brief explanation of physical fundamentals and design methods. The key fabrication methods corresponding to various optical fiber metasurfaces are summarized and compared. Furthermore, the challenges and potential future research directions of optical fiber metasurfaces are addressed to further leverage the flexibility and versatility of meta-fiber-based devices. It is believed that the optical fiber metasurfaces, as a novel all-around technological platform, will be exploited for a large range of applications in telecommunication, sensing, imaging, and biomedicine.
Collapse
|
43
|
Dalloz N, Le VD, Hebert M, Eles B, Flores Figueroa MA, Hubert C, Ma H, Sharma N, Vocanson F, Ayala S, Destouches N. Anti-Counterfeiting White Light Printed Image Multiplexing by Fast Nanosecond Laser Processing. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2104054. [PMID: 34648203 DOI: 10.1002/adma.202104054] [Citation(s) in RCA: 8] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/28/2021] [Revised: 08/14/2021] [Indexed: 06/13/2023]
Abstract
Passive plasmonic metasurfaces enable image multiplexing by displaying different images when altering the conditions of observation. Under white light, three-image multiplexing with polarization-selective switching has been recently demonstrated using femtosecond-laser-processed random plasmonic metasurfaces. Here, the implementation of image multiplexing is extended, thanks to a color-search algorithm, to various observation modes compatible with naked-eye observation under incoherent white light and to four-image multiplexing under polarized light. The laser-processed random plasmonic metasurfaces enabling image multiplexing exhibit self-organized patterns that can diffract light or induce dichroism through hybridization between the localized surface plasmon resonance of metallic nanoparticles and a lattice resonance. Improved spatial resolution makes the image quality compatible with commercial use in secured documents as well as the processing time and cost thanks to the use of a nanosecond laser. This high-speed and flexible laser process, based on energy-efficient nanoparticle reshaping and self-organization, produces centimeter-scale customized tamper-proof images at low cost, which can serve as overt security features.
Collapse
Affiliation(s)
- Nicolas Dalloz
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
- HID Global CID SAS, 33 rue de Verdun, Suresnes, 92100, France
| | - Van Doan Le
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Mathieu Hebert
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Balint Eles
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Manuel A Flores Figueroa
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Christophe Hubert
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Hongfeng Ma
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Nipun Sharma
- HID Global CID SAS, 33 rue de Verdun, Suresnes, 92100, France
| | - Francis Vocanson
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| | - Stéphane Ayala
- HID Global Switzerland SA, Z.I., Rte Pra-Charbon 27, Granges, FR 1614, Switzerland
| | - Nathalie Destouches
- Laboratoire Hubert Curien UMR 5516, Univ Lyon, UJM-Saint-Etienne, CNRS, Institut d Optique Graduate School, 18 rue Professeur Benoît Lauras, Saint-Etienne, 42000, France
| |
Collapse
|
44
|
Audhkhasi R, Povinelli ML. Generalized multi-channel scheme for secure image encryption. Sci Rep 2021; 11:22669. [PMID: 34811428 PMCID: PMC8608829 DOI: 10.1038/s41598-021-02067-8] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/06/2021] [Accepted: 11/02/2021] [Indexed: 11/09/2022] Open
Abstract
The ability of metamaterials to manipulate optical waves in both the spatial and spectral domains has provided new opportunities for image encoding. Combined with the recent advances in hyperspectral imaging, this suggests exciting new possibilities for the development of secure communication systems. While traditional image encryption approaches perform a 1-to-1 transformation on a plain image to form a cipher image, we propose a 1-to-n transformation scheme. Plain image data is dispersed across n seemingly random cipher images, each transmitted on a separate spectral channel. We show that the size of our key space increases as a double exponential with the number of channels used, ensuring security against both brute-force attacks and more sophisticated attacks based on statistical sampling. Moreover, our multichannel scheme can be cascaded with a traditional 1-to-1 transformation scheme, effectively squaring the size of the key space. Our results suggest exciting new possibilities for secure transmission in multi-wavelength imaging channels.
Collapse
Affiliation(s)
- Romil Audhkhasi
- Ming Hsieh Department of Electrical and Computer Engineering, University of Southern California, Los Angeles, CA, 90089, USA
| | - Michelle L Povinelli
- Ming Hsieh Department of Electrical and Computer Engineering, University of Southern California, Los Angeles, CA, 90089, USA.
| |
Collapse
|
45
|
Wang R, Xu L, Wang J, Sun L, Jiao Y, Meng Y, Chen S, Chang C, Fan C. Electric Fano resonance-based terahertz metasensors. NANOSCALE 2021; 13:18467-18472. [PMID: 34726683 DOI: 10.1039/d1nr04477j] [Citation(s) in RCA: 27] [Impact Index Per Article: 9.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/28/2023]
Abstract
An ultra-sensitive THz metasensor is presented based on quasi-BIC Fano resonance, which can distinguish extremely dilute concentrations (nM) of solutions. It provides a nondestructive sensing approach for disease prevention and diagnosis. However, the main drawback limiting the performance of THz-based bio-chemical sensors is the weak interaction between the optical field and the analyte, the characteristic scale of which is mismatched with the THz wavelength, leading to low sensitivity. Herein, we present an ultra-sensitive THz metasensor based on an electric Fano resonant metasurface which consists of three gold microrods arranged periodically. The designed electric Fano resonance provides a strong near-field enhancement near the surface of the microstructure, significantly boosting the light-analyte interactions and thus the sensitivity. Such an electric Fano resonance is formed by the interference between a leaky electric dipole resonance and a bound toroidal dipole mode which is a symmetry-protected bound state in the continuum supported by the sub-diffractive periodic system here. Owing to the strong electric fields generated near the interface of our microstructure around the toroidal dipole BIC, the proposed structure can distinguish extremely dilute concentrations (nM) of solutions. Importantly, by controlling the degree of geometrical asymmetry, the BIC-inspired mechanism provides an important and simple tool to engineer and tailor the linewidth and Q-factor of our proposed electric Fano resonance, indicating the ability to realize different biosensors for different optical regimes. Our results open new possibilities to realize a non-destructive and non-contact quantitative inspection of low-concentration solutions, providing a useful sensing approach for disease prevention and diagnosis.
Collapse
Affiliation(s)
- Ride Wang
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing, 100071, China.
| | - Lei Xu
- Advanced Optics and Photonics Laboratory, Department of Engineering, School of Science and Technology, Nottingham Trent University, Nottingham NG11 8NS, UK
| | - Jiayi Wang
- Key Laboratory of Weak-Light Nonlinear Photonics, Ministry of Education, TEDA Institute of Applied Physics and School of Physics, Nankai University, Tianjin 300457, China
| | - Lang Sun
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing, 100071, China.
| | - Yanan Jiao
- Department of General Surgery, First Medical Center of Chinese PLA General Hospital, Beijing 100853, People's Republic of China
| | - Yuan Meng
- Key Laboratory of Photonics Control Technology of the Ministry of Education, Tsinghua University, China
| | - Shuo Chen
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing, 100071, China.
| | - Chao Chang
- Innovation Laboratory of Terahertz Biophysics, National Innovation Institute of Defense Technology, Beijing, 100071, China.
- School of Physics, Peking University, Beijing, 100871, China
| | - Chunhai Fan
- School of Chemistry and Chemical Engineering, Shanghai Jiao Tong University, Shanghai, 200240, China.
| |
Collapse
|
46
|
Li W, Zeng X, Dong Y, Feng Z, Wen H, Chen Q, Wen L, Song S, Li X, Cao Y. Laser nanoprinting of floating three-dimensional plasmonic color in pH-responsive hydrogel. NANOTECHNOLOGY 2021; 33:065302. [PMID: 34710861 DOI: 10.1088/1361-6528/ac345b] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/24/2021] [Accepted: 10/28/2021] [Indexed: 06/13/2023]
Abstract
Recent demonstrations of metasurfaces present their great potential to implement flat and multifunctional optical elements, which are accomplished with the designs of planar optics and micro-/nano- fabrications. Integrating metasurfaces in three dimensions has manifested drastically increasing advantages in manipulating light fields by extending design freedom. However, fabricating three-dimensional metasurfaces remain a tough challenge due to the lack of stereo printing protocols. Herein, we demonstrate laser nanoprinting of floated silver nanoparticle array in transparent hydrogel films for 3D metasurface to achieve color patterning. It is found that spatially resolved nanoparticles can be produced through laser induced photoreduction of silver ions and robustly anchored to the gel backbones by a focused femtosecond laser beam within a pH-responsive smart hydrogel matrix. With the aid of expansion properties of the pH-responsive hydrogel, repetitive coloration of the patterned plasmonic nanoparticle array over a wide spectrum range is achieved via reversible regulation of nanoparticle spacing from 550 to 350 nm and vice versa. This approach allows broadband 3D color-regulation in nanoscale for applications in active spectral filtering, information encryption, security tagging and biological colorimetric sensing, etc.
Collapse
Affiliation(s)
- Wanyi Li
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
- Wuxi University, Wuxi 214105, People's Republic of China
| | - Xianzhi Zeng
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
| | - Yajing Dong
- Institute of Nanophotonics, Jinan University, Guangzhou 511443, People's Republic of China
| | - Ziwei Feng
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
| | - Hongjing Wen
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
| | - Qin Chen
- Institute of Nanophotonics, Jinan University, Guangzhou 511443, People's Republic of China
| | - Long Wen
- Institute of Nanophotonics, Jinan University, Guangzhou 511443, People's Republic of China
| | - Shichao Song
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
| | - Xiangping Li
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
| | - Yaoyu Cao
- Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications, Institute of Photonics Technology, Jinan University, Guangzhou 511443, People's Republic of China
| |
Collapse
|
47
|
Jung C, Kim G, Jeong M, Jang J, Dong Z, Badloe T, Yang JKW, Rho J. Metasurface-Driven Optically Variable Devices. Chem Rev 2021; 121:13013-13050. [PMID: 34491723 DOI: 10.1021/acs.chemrev.1c00294] [Citation(s) in RCA: 59] [Impact Index Per Article: 19.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/11/2022]
Abstract
Optically variable devices (OVDs) are in tremendous demand as optical indicators against the increasing threat of counterfeiting. Conventional OVDs are exposed to the danger of fraudulent replication with advances in printing technology and widespread copying methods of security features. Metasurfaces, two-dimensional arrays of subwavelength structures known as meta-atoms, have been nominated as a candidate for a new generation of OVDs as they exhibit exceptional behaviors that can provide a more robust solution for optical anti-counterfeiting. Unlike conventional OVDs, metasurface-driven OVDs (mOVDs) can contain multiple optical responses in a single device, making them difficult to reverse engineered. Well-known examples of mOVDs include ultrahigh-resolution structural color printing, various types of holography, and polarization encoding. In this review, we discuss the new generation of mOVDs. The fundamentals of plasmonic and dielectric metasurfaces are presented to explain how the optical responses of metasurfaces can be manipulated. Then, examples of monofunctional, tunable, and multifunctional mOVDs are discussed. We follow up with a discussion of the fabrication methods needed to realize these mOVDs, classified into prototyping and manufacturing techniques. Finally, we provide an outlook and classification of mOVDs with respect to their capacity and security level. We believe this newly proposed concept of OVDs may bring about a new era of optical anticounterfeit technology leveraging the novel concepts of nano-optics and nanotechnology.
Collapse
Affiliation(s)
- Chunghwan Jung
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Gyeongtae Kim
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Minsu Jeong
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Jaehyuck Jang
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Zhaogang Dong
- Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 138634, Singapore
| | - Trevon Badloe
- Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea
| | - Joel K W Yang
- Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 138634, Singapore.,Engineering Product Development, Singapore University of Technology and Design, 487372, Singapore
| | - Junsuk Rho
- Department of Chemical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.,Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH), Pohang 37673, Republic of Korea.,POSCO-POSTECH-RIST Convergence Research Center for Flat Optics and Metaphotonics, Pohang 37673, Republic of Korea
| |
Collapse
|
48
|
Yang W, Qu G, Lai F, Liu Y, Ji Z, Xu Y, Song Q, Han J, Xiao S. Dynamic Bifunctional Metasurfaces for Holography and Color Display. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2021; 33:e2101258. [PMID: 34309091 DOI: 10.1002/adma.202101258] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/13/2021] [Revised: 04/21/2021] [Indexed: 06/13/2023]
Abstract
Metasurfaces have shown their unprecedented ability in wavefront shaping and triggered various applications with state-of-the-art performances, e.g., color nanoprinting and metaholograms. Recently, these two functions have been combined into a single metasurface to further expand its capabilities. Despite the progress, the current dual-mode metasurfaces are mostly static and strongly hinder their practical applications. Herein, the realization of dynamic bifunctional metasurfaces is reported. Five metaholograms at two different wavelengths are multiplexed with structural colors by controlling the spectral and phase response of metasurface. Owing to the destructive interference and the resonance on external environment, the light diffraction at particular wavelengths can be switched between "ON" and "OFF" states, or remain unchanged with the change of surrounding refractive index. Consequently, the encoded metaholograms are selectively turned on and off, making the overall holographic image dynamically switchable. This concept paves a solid step toward practical applications of all-dielectric metasurfaces.
Collapse
Affiliation(s)
- Wenhong Yang
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Geyang Qu
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Fangxing Lai
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Yilin Liu
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Ziheng Ji
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Yi Xu
- Department of Electronic Engineering, College of Information Science and Technology, Jinan University, Guangzhou, 510632, China
| | - Qinghai Song
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Jiecai Han
- School of Materials Science and Engineering, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
| | - Shumin Xiao
- State Key Laboratory on Tunable laser Technology, Ministry of Industry and Information Technology Key Lab of Micro-Nano Optoelectronic Information System, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
- School of Materials Science and Engineering, Shenzhen Graduate School, Harbin Institute of Technology, Shenzhen, 518055, China
- Collaborative Innovation Center of Extreme Optics, Shanxi University, Taiyuan, 030006, China
| |
Collapse
|
49
|
Abstract
The full manipulation of intrinsic properties of electromagnetic waves has become the central target in various modern optical technologies. Optical metasurfaces have been suggested for a complete control of light-matter interaction with subwavelength structures, and they have been explored widely in the past decade for creating next-generation multifunctional flat-optics devices. The current studies of metasurfaces have reached a mature stage where common materials, basic optical physics, and conventional engineering tools have been explored extensively for various applications such as light bending, metalenses, metaholograms, and many others. A natural question is where the future research on metasurfaces will be going: Quo vadis, metasurfaces? In this Mini Review, we provide perspectives on the future developments of optical metasurfaces. Specifically, we highlight recent progresses on hybrid metasurfaces employing low-dimensional materials and discuss biomedical, computational, and quantum applications of metasurfaces, followed by discussions of challenges and foreseeing the future of metasurface physics and engineering.
Collapse
Affiliation(s)
- Cheng-Wei Qiu
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore 117583
| | - Tan Zhang
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore 117583
| | - Guangwei Hu
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore 117583
| | - Yuri Kivshar
- Nonlinear Physics Center, Research School of Physics, Australian National University, Canberra, Australian Capital Territory 2601, Australia
| |
Collapse
|
50
|
Cubic-Phase Metasurface for Three-Dimensional Optical Manipulation. NANOMATERIALS 2021; 11:nano11071730. [PMID: 34209225 PMCID: PMC8308168 DOI: 10.3390/nano11071730] [Citation(s) in RCA: 5] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 06/11/2021] [Revised: 06/26/2021] [Accepted: 06/28/2021] [Indexed: 02/06/2023]
Abstract
The optical tweezer is one of the important techniques for contactless manipulation in biological research to control the motion of tiny objects. For three-dimensional (3D) optical manipulation, shaped light beams have been widely used. Typically, spatial light modulators are used for shaping light fields. However, they suffer from bulky size, narrow operational bandwidth, and limitations of incident polarization states. Here, a cubic-phase dielectric metasurface, composed of GaN circular nanopillars, is designed and fabricated to generate a polarization-independent vertically accelerated two-dimensional (2D) Airy beam in the visible region. The distinctive propagation characteristics of a vertically accelerated 2D Airy beam, including non-diffraction, self-acceleration, and self-healing, are experimentally demonstrated. An optical manipulation system equipped with a cubic-phase metasurface is designed to perform 3D manipulation of microscale particles. Due to the high-intensity gradients and the reciprocal propagation trajectory of Airy beams, particles can be laterally shifted and guided along the axial direction. In addition, the performance of optical trapping is quantitatively evaluated by experimentally measured trapping stiffness. Our metasurface has great potential to shape light for compact systems in the field of physics and biological applications.
Collapse
|