Cellulose Nanofibrils Endow Phase-Change Polyethylene Glycol with Form Control and Solid-to-gel Transition for Thermal Energy Storage

Stabilization and strengthening effects of filamentous nanocellulose in the foam forming of quartz paper

Compared with traditional papermaking, foam forming is a new papermaking technology that uses foam instead of water to disperse fibres, which can effectively solve the problem of poor evenness of ceramic paper, but the instability of foam itself affects the application of foam forming technology. Herein, a highly stable foaming agent for foam forming technology was prepared via physical reaction of lauryl dimethyl amine oxide (OB-2) with filamentous nanocellulose (cellulose nanofiber (CNF-C) and bacterial cellulose (BC)). Then, the quartz paper was prepared by foam forming technology. Firstly, hydrogen bond interactions between hydroxyl groups of the filamentous nanocellulose and hydrophilic moieties on OB-2 enabled the formation of a 3D nanonetwork layer on the surface of the bubble, which extended the half-life of the bubble and effectively prevented the bubble from bursting or coalescing. Then, the foam was extruded and cracked, and the filamentous nanocellulose was retained on the quartz fibres to prepare filamentous nanocellulose/quartz fibre paper by foam forming technology. The quartz paper exhibited excellent evenness and mechanical properties. In conclusion, the research of foam forming technology is of great significance to the application and development of special paper.

Green, recyclable and high latent heat form-stable phase change composites supported by cellulose nanofibers for thermal energy management

Efficiently addressing the challenge of leakage is crucial in the advancement of solid-liquid phase change thermal storage composite materials; however, numerous existing preparation methods often entail complexity and high energy consumption. Herein, a straightforward blending approach was adopted to fabricate stable phase change nanocomposites capitalizing on the interaction between TEMPO-oxidized cellulose nanofibers (TOCNF) and polyethylene glycol (PEG) molecules. By adjusting the ratio of TOCNF to PEG and the molecular weights of PEG, TOCNF/PEG phase change composites (TPCC) with customizable phase transition temperature (40.3-59.1 °C) and high phase transition latent heat (126.3-172.1 J/g) were obtained. The TPCC of high-loaded PEG (80-95 wt%) ensured a leakage rate of less than 1.7 wt% after 100 heating-cooling cycles. Moreover, TPCC exhibits excellent optical properties with a transmittance of over 90 % at room temperature and up to 96 % after heating. The thermal response analysis of TPCC demonstrates exceptional thermal-induced flexibility and good thermal stability, as well as recyclability and reshaping ability. This study may inspire others to design bio-based phase change composites with potential applications in thermal energy storage and management of smart-energy buildings, photothermal response devices, and waste heat-generating electronics.

Dimensionally Stable Delignified Bamboo Matrix Phase-Change Composite under Ambient Temperature for Indoor Thermal Regulation

Energy storage materials to modulate indoor microclimates are needed to improve energy efficiency and for human comfort. Of these, phase-change material (PCM) is considered a very useful material because of its excellent latent heat energy storage. For application, some synthetic porous materials for supporting PCM are usually not friendly enough for people and housing environments due to their non-degradation characteristics. Hence, to develop an eco-friendly porous material is needed in order to encapsulate PCM composites that are always expected in indoor applications. In this work, heat-treated bamboo bricks were delignified to provide a delignified bamboo (DB) matrix. A phase-change composite was then fabricated by impregnating DB with polyethylene glycol (PEG) polymer. Impregnation was carried out under wet conditions to ensure the regular arrangement of the DB structure so as to achieve dimensional stability. The final DB/PEG composite was investigated for dimensional stability, load rate, latent heat, and phase-change temperature. Results showed that the DB matrix could be easily impregnated with PEG polymer under wet conditions, and the DB/PEG composite was found to have high enthalpy and a large phase-change temperature interval. Moreover, the composite was found to be a good regulator of indoor temperature and a stable dimension with a snow-white appearance. In summary, this DB/PEG composite is an energy storage material with the potential to modulate ambient indoor temperature and reduce building energy consumption.

Phase Change Energy Storage Material with Photocuring, Photothermal Conversion, and Self-Cleaning Performance via a Two-Layer Structure

Compared with the thermal curing process, the photocuring process has advantages such as high efficiency and less energy consumption. However, the preparation of photocurable phase change materials (PCMs) with photothermal conversion and self-cleaning properties is challenging due to the conflict between the transparency required by the photocurable resin system and the opacity deduced by the large number of fillers required by photothermal conversion and the negative effect of filler steric hindrance on the reaction rate and crystallinity. In this work, a "thiol-ene" click chemical reaction induced using UV was used to prepare photocurable PCMs, followed by spraying a carboxylated multiwalled carbon nanotube (CCNT) suspension (with ethyl acetate) onto the surface to achieve an effective two-layer composite of the PCM and CCNTs, by which the rough surface of the PCM and the interaction offered by the hydrogen bonds on the interface of the PCM and the CCNTs provide sufficient adhesion for the two phases. The "thiol-ene" cross-linked polymer network provided shape stability as a support material. 1-Octadectanethiol (ODT) and beeswax (BW) were encapsulated in the cross-linked polymer network as phase change components, providing phase change latent heat. The CCNT layer provided excellent photothermal conversion and self-cleaning properties. The experimental results show that the latent heat of the PCM can reach 124.2 J/g, the water contact angle is 144°, the photothermal conversion efficiency reaches 75%, and it has significant self-cleaning performance. To the best of our knowledge, this is the first report on a photocurable PCM with photothermal conversion and self-cleaning properties.

Hysteresis in the thermally induced phase transition of cellulose ethers

Functionalized cellulosics have shown promise as naturally derived thermoresponsive gelling agents. However, the dynamics of thermally induced phase transitions of these polymers at the lower critical solution temperature (LCST) are not fully understood. Here, with experiments and theoretical considerations, we address how molecular architecture dictates the mechanisms and dynamics of phase transitions for cellulose ethers. Above the LCST, we show that hydroxypropyl substituents favor the spontaneous formation of liquid droplets, whereas methyl substituents induce fibril formation through diffusive growth. In celluloses which contain both methyl and hydroxypropyl substituents, fibrillation initiates after liquid droplet formation, suppressing the fibril growth to a sub-diffusive rate. Unlike for liquid droplets, the dissolution of fibrils back into the solvated state occurs with significant thermal hysteresis. We tune this hysteresis by altering the content of substituted hydroxypropyl moieties. This work provides a systematic study to decouple competing mechanisms during the phase transition of multi-functionalized macromolecules.

Hollow Filaments Synthesized by Dry-Jet Wet Spinning of Cellulose Nanofibrils: Structural Properties and Thermoregulation with Phase-Change Infills

We use dry-jet wet spinning in a coaxial configuration by extruding an aqueous colloidal suspension of oxidized nanocellulose (hydrogel shell) combined with airflow in the core. The coagulation of the hydrogel in a water bath results in hollow filaments (HF) that are drawn continuously at relatively high rates. Small-angle and wide-angle X-ray scattering (SAXS/WAXS) reveals the orientation and order of the cellulose sheath, depending on the applied shear flow and drying method (free-drying and drying under tension). The obtained dry HF show Young's modulus and tensile strength of up to 9 GPa and 66 MPa, respectively. Two types of phase-change materials (PCM), polyethylene glycol (PEG) and paraffin (PA), are used as infills to enable filaments for energy regulation. An increased strain (9%) is observed in the PCM-filled filaments (HF-PEG and HF-PA). The filaments display similar thermal behavior (dynamic scanning calorimetry) compared to the neat infill, PEG, or paraffin, reaching a maximum latent heat capacity of 170 J·g^-1 (48-55 °C) and 169 J·g^-1 (52-54 °C), respectively. Overall, this study demonstrates the facile and scalable production of two-component core-shell filaments that combine structural integrity, heat storage, and thermoregulation properties.

Sonication-Induced, Solvent-Selective Gelation of a 1,8-Napthalimide-Conjugated Amide: Structural Insights and Pollutant Removal Applications

Reported herein is the synthesis, characterization, and dye removal applications of a highly solvent-selective organogel-forming amide, compound 1, which contains a 1,8-naphthalmide moiety, flexible n-hexyl chain, and benzene ring. This compound displayed remarkable solvent selectivity, with gel formation occurring only in the presence of alkylated aromatic solvents. Detailed structural characterization of the gels, combined with notable theoretical insights, is invoked to explain the highly selective gelation properties of compound 1, as is a comparison to non-gel forming structural isomer 2, which contains the same structural elements in a different arrangement. Finally, the ability of the gel derived from compound 1 to act as a reusable material for the efficient removal of cationic organic dyes from contaminated aqueous environments is also reported, with up to 11 repeated uses of the gel still maintaining the ability to effectively remove Rhodamine B.

Design and Fabrication of Epichlorohydrin-Cross-Linked Methyl Cellulose Aerogel-Based Composite Materials for Magnetic UV Response Light-to-Heat Conversion and Storage

The collection, storage, and use of energy and information are important issues for overcoming the global energy shortage while satisfying the demand for information transmission. This research reports a nano-Fe₃O₄ and erythritol (ER)-functionalized, cross-linked methyl cellulose aerogel (MC-EP) composite that has the characteristics of phase-change energy storage as the magnetic and ultraviolet responses requisite for light-to-heat conversion and storage. The nano-Fe₃O₄ particles in MC-EP-ER-75 were fixed and filled into pore structures in MC-EP. ER was used to form an effective combination with MC-EP. The addition of nano-Fe₃O₄ compensated for the low thermal conductivity of ER. The MC-EP-ER-75 was able to store solar radiation-induced energy due to the loading of ER at a photothermal conversion efficiency of 79.67% and a light-to-heat conversion efficiency of 79.67%. The results of thermal stability (TGA) analysis showed that MC-EP-ER-75 was thermally degraded acceptably below 200 °C. The differential scanning calorimetry curve and latent heat values (melting/crystallization enthalpies of 314.8 and 197.9 J/g, respectively) of MC-EP-ER-75 did not change after 100 cycles. In addition, it exhibited excellent saturation magnetization, super-paramagnetism, and ultraviolet shielding, as well as a rapid response to the ultraviolet and magnetic fields. This provided a way to prepare light-to-heat conversion-storage-release materials and ultraviolet-magnetic sensors that can be used in renewable resources.

Recent Advances in Design and Preparation of Polymer-Based Thermal Management Material

The boosting of consumer electronics and 5G technology cause the continuous increment of the power density of electronic devices and lead to inevitable overheating problems, which reduces the operation efficiency and shortens the service life of electronic devices. Therefore, it is the primary task and a prerequisite to explore innovative material for meeting the requirement of high heat dissipation performance. In comparison with traditional thermal management material (e.g., ceramics and metals), the polymer-based thermal management material exhibit excellent mechanical, electrical insulation, chemical resistance and processing properties, and therefore is considered to be the most promising candidate to solve the heat dissipation problem. In this review, we summarized the recent advances of two typical polymer-based thermal management material including thermal-conduction thermal management material and thermal-storage thermal management material. Furtherly, the structural design, processing strategies and typical applications for two polymer-based thermal management materials were discussed. Finally, we proposed the challenges and prospects of the polymer-based thermal management material. This work presents new perspectives to develop advanced processing approaches and construction high-performance polymer-based thermal management material.

Shape-Stable Hydrated Salts/Polyacrylamide Phase-Change Organohydrogels for Smart Temperature Management

Flexible and environmentally friendly phase-change materials (PCMs) with appropriate phase transition temperatures display great potential in the regulation of environmental temperature. Here, we synthesized a series of room-temperature-use phase-change organohydrogels (PCOHs) comprising phase-change hydrated salts (disodium phosphate dodecahydrate, DPDH) and polyacrylamide (PAM) glycerol hydrogels through a facile photoinitiated one-step in situ polymerization procedure. Incorporating the environmentally friendly cost-effective DPDH hydrated salts PCMs into antidrying three-dimensional (3D) networks of the PAM organohydrogel can overcome the solid rigidity and melting leakage to achieve flexibility for wearable temperature management devices. The microstructures and physical interactions among the components of the PCOHs were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), and X-ray diffraction (XRD), which demonstrate that the DPDH were uniformly loaded in the networks of the PAM. Phase-change storage and thermal properties of the PCOHs were characterized by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA), and the PCOHs show high energy transition efficiency and shape stability during the long-term storage and thermal cycling. Dynamic rheology and compression tests demonstrate that PCOHs can withstand a certain stress and display flexibility performance even above the melting temperature of DPDH. We also described the smart temperature management capability and the potential application of the PCOHs. This investigation offers a facile method to construct a skin-friendly flexible phase-change glycerol hydrogel and provides an alternative to the traditional melt impregnation or microencapsulation method to prepare phase-change energy storage composites.