Transparent Anti-SARS-CoV-2 and Antibacterial Silver Oxide Coatings

Therapeutic strategies for drug-resistant Pseudomonas aeruginosa: Metal and metal oxide nanoparticles

Pseudomonas aeruginosa (PA) is a widely prevalent opportunistic pathogen. Multiple resistant strains of PA have emerged from excessive or inappropriate use of antibiotics, making their eradication increasingly difficult. Therefore, the search for highly efficient and secure novel antimicrobial agents is crucial. According to reports, there is an increasing exploration of nanometals for antibacterial purposes. The antibacterial mechanisms involving the nanomaterials themselves, the release of ions, and the induced oxidative stress causing leakage and damage to biomolecules are widely accepted. Additionally, the study of the cytotoxicity of metal nanoparticles is crucial for their antibacterial applications. This article summarizes the types of metal nanomaterials and metal oxide nanomaterials that can be used against PA, their respective unique antibacterial mechanisms, cytotoxicity, and efforts made to improve antibacterial performance and reduce toxicity, including combination therapy with other materials and antibiotics, as well as green synthesis approaches.

The role of ion dissolution in metal and metal oxide surface inactivation of SARS-CoV-2

Anti-viral surface coatings are under development to prevent viral fomite transmission from high-traffic touch surfaces in public spaces. Copper's anti-viral properties have been widely documented, but the anti-viral mechanism of copper surfaces is not fully understood. We screened a series of metal and metal oxide surfaces for anti-viral activity against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the causative agent of coronavirus disease (COVID-19). Copper and copper oxide surfaces exhibited superior anti-SARS-CoV-2 activity; however, the level of anti-viral activity was dependent on the composition of the carrier solution used to deliver virus inoculum. We demonstrate that copper ions released into solution from test surfaces can mediate virus inactivation, indicating a copper ion dissolution-dependent anti-viral mechanism. The level of anti-viral activity is, however, not dependent on the amount of copper ions released into solution per se. Instead, our findings suggest that degree of virus inactivation is dependent on copper ion complexation with other biomolecules (e.g., proteins/metabolites) in the virus carrier solution that compete with viral components. Although using tissue culture-derived virus inoculum is experimentally convenient to evaluate the anti-viral activity of copper-derived test surfaces, we propose that the high organic content of tissue culture medium reduces the availability of "uncomplexed" copper ions to interact with the virus, negatively affecting virus inactivation and hence surface anti-viral performance. We propose that laboratory anti-viral surface testing should include virus delivered in a physiologically relevant carrier solution (saliva or nasal secretions when testing respiratory viruses) to accurately predict real-life surface anti-viral performance when deployed in public spaces.IMPORTANCEThe purpose of evaluating the anti-viral activity of test surfaces in the laboratory is to identify surfaces that will perform efficiently in preventing fomite transmission when deployed on high-traffic touch surfaces in public spaces. The conventional method in laboratory testing is to use tissue culture-derived virus inoculum; however, this study demonstrates that anti-viral performance of test copper-containing surfaces is dependent on the composition of the carrier solution in which the virus inoculum is delivered to test surfaces. Therefore, we recommend that laboratory surface testing should include virus delivered in a physiologically relevant carrier solution to accurately predict real-life test surface performance in public spaces. Understanding the mechanism of virus inactivation is key to future rational design of improved anti-viral surfaces. Here, we demonstrate that release of copper ions from copper surfaces into small liquid droplets containing SARS-CoV-2 is a mechanism by which the virus that causes COVID-19 can be inactivated.

Robust and Transparent Silver Oxide Coating Fabricated at Room Temperature Kills Clostridioides difficile Spores, MRSA, and Pseudomonas aeruginosa

Antimicrobial coatings can inhibit the transmission of infectious diseases when they provide a quick kill that is achieved long after the coating application. Here, we describe the fabrication and testing of a glass coating containing Ag2O microparticles that was prepared from sodium silicate at room temperature. The half-lives of both methicillin-resistant Staphylococcus aureus (MRSA) and Pseudomonas aeruginosa on this coating are only 2-4 min. The half-life of Clostridioides difficile spores is about 9-12 min, which is extremely short for a spore. Additional tests on MRSA demonstrate that the coating retains its antimicrobial activity after abrasion and that an increased loading of Ag2O leads to a shorter half-life. This coating combines the properties of optical transparency, robustness, fast kill, and room temperature preparation that are highly desirable for an antimicrobial coating.

Structurally Heterogeneous Amphiphilic Conetworks of Poly(vinyl imidazole) Derivatives with Potent Antimicrobial Properties and Cytocompatibility

We report the construction of amphiphilic conetwork (APCN)-based surfaces with potent antimicrobial activity and biofilm inhibition ability. The construction strategy is based on the separation of lipophilic alkyl groups (>C6) from the cationic network to obtain good antibacterial properties. The reaction of partially alkylated poly(vinyl imidazole) with the activated halide compounds followed by coating a glass or poly(dimethylsiloxane) (PDMS) sheet leads to the formation of the APCN surface. The dangling alkyl chains, crosslinking junctions, and unreacted vinyl imidazole groups are heterogeneously distributed in the APCNs. The swelling, mechanical property, and phase morphology of the APCN films have been evaluated. Bacterial cell disrupting potency of the APCN coatings increases with increasing alkyl chain length from C6 to C18 with somewhat more of an effect on Escherichia coli as compared to Bacillus subtilis bacteria. The minimum inhibitory amount of the APCNs on glass and a hydrophobic PDMS surface is in the range of 0.02-0.04 mg/cm2 depending on the chain length of the alkyl and the degree of quaternization. The effect of the type of crosslinker for the construction of the conetwork on the antimicrobial property has been evaluated to elucidate the exclusive design of the APCNs. The APCN-based coatings provide potent biocidal activity without much negatively affecting the hemocompatibility and cytocompatibility. These APCNs provide a good model system for comparative evaluation of the biocidal property and structural effect on the biocidal activity.

Virus on surfaces: Chemical mechanism, influence factors, disinfection strategies, and implications for virus repelling surface design

While SARS-CoV-2 is generally under control, the question of variants and infections still persists. Fundamental information on how the virus interacts with inanimate surfaces commonly found in our daily life and when in contact with the skin will be helpful in developing strategies to inhibit the spread of the virus. Here in, a critically important review of current understanding of the interaction between virus and surface is summarized from chemistry point-of-view. The Derjaguin-Landau-Verwey-Overbeek and extended Derjaguin-Landau-Verwey-Overbeek theories to model virus attachments on surfaces are introduced, along with the interaction type and strength, and quantification of each component. The virus survival and transfer are affected by a combination of biological, physical, and chemical parameters, as well as environmental parameters. The surface properties for virus and virus survival on typical surfaces such as metals, plastics, and glass are summarized. Attention is also paid to the transfer of virus to/from surfaces and skin. Typical virus disinfection strategies utilizing heat, light, chemicals, and ozone are discussed together with their disinfection mechanism. In the last section, design principles for virus repelling surface chemistry such as surperhydrophobic or surperhydrophilic surfaces are also introduced, to demonstrate how the integration of surface property control and advanced material fabrication can lead to the development of functional surfaces for mitigating the effect of viral infection upon contact.

Biomedical equipments, vaccine and drug in the prevention, diagnosis and treatment of COVID-19

SARS-CoV-2 virus caused an infectious disease, named COVID-19. Biomedical equipments, vaccine and drug have played a crucial role in the prevention, diagnosis and treatment. Nevertheless, up to now, there still has been no literature summarizing the diagnosis, prevention and treatment of this infectious disease from the perspective of biomedical equipments. Thus, this review wants to give an overview on the biomedical equipments, vaccine and drug in the prevention, diagnosis and treatment of this disease, and avoids the overlap with previous research, more emphasis on biomedical equipments, and less emphasis on biomaterials. The existing problems in the current research and application were summarized, and the future research direction was proposed, so as to provide reference to deal with similar viral infections in the future.

Creating anti-viral high-touch surfaces using photocatalytic transparent films

Antimicrobial and self-cleaning surface coatings are promising tools to combat the growing global threat of infectious diseases and related healthcare-associated infections (HAIs). Although many engineered TiO₂-based coating technologies are reporting antibacterial performance, the antiviral performance of these coatings has not been explored. Furthermore, previous studies have underscored the importance of the "transparency" of the coating for surfaces such as the touch screens of medical devices. Hence, in this study, we fabricated a variety of nanoscale TiO₂-based transparent thin films (anatase TiO₂, anatase/rutile mixed phase TiO₂, silver-anatase TiO₂ composite, and carbon nanotube-anatase TiO₂ composite) via dipping and airbrush spray coating technologies and evaluated their antiviral performance (Bacteriophage MS2 as the model) under dark and illuminated conditions. The thin films showed high surface coverage (ranging from 40 to 85%), low surface roughness (maximum average roughness 70 nm), super-hydrophilicity (water contact angle 6-38.4°), and high transparency (70-80% transmittance under visible light). Antiviral performance of the coatings revealed that silver-anatase TiO₂ composite (nAg/nTiO₂) coated samples achieved the highest antiviral efficacy (5-6 log reduction) while the other TiO₂ coated samples showed fair antiviral results (1.5-3.5 log reduction) after 90 min LED irradiation at 365 nm. Those findings indicate that TiO₂-based composite coatings are effective in creating antiviral high-touch surfaces with the potential to control infectious diseases and HAIs.

Virus Inactivation Based on Optimal Surfactant Reservoir of Mesoporous Silica

SARS-CoV-2 (severe acute respiratory syndrome coronavirus 2) caused a pandemic in 2019 and reaffirmed the importance of environmental sanitation. To prevent the spread of viral infections, we propose the application of a mesoporous silica (MS)-based virus-inactivating material. MS is typically synthesized using a micellar surfactant template; hence, the intermediate before removal of the surfactant template is expected to have a virus-inactivating activity. MS-CTAC particles filled with cetyltrimethylammonium chloride (CTAC), a cationic surfactant with an alkyl chain length of 16, were used to test this hypothesis. Plaque assays revealed that the MS-CTAC particles inactivated the enveloped bacteriophage φ6 by approximately 4 orders of magnitude after a contact time of 10 min. The particles also indicated a similar inactivation effect on the nonenveloped bacteriophage Qβ. In aqueous solution, CTAC loaded on MS-CTAC was released until the equilibrium concentration of loading and release on MS was reached. The released CTAC acted on viruses. Thus, MS is likely a good reservoir for the micellar surfactant. Surfactant readsorption also occurred in the MS particles, and the highest retention rate was observed when micellar surfactants with alkyl chain lengths appropriate for the pore size were used. The paper containing MS-CTAC particles was shown to maintain stable viral inactivation for at least three months in a typical indoor environment. Applying this concept to indoor wallpaper and air-conditioning filters could contribute to the inactivation of viruses in aerosols. These findings open possibilities for mesoporous materials with high surface areas, which can further develop into virus inactivation materials.

Progress in Polymer-Ceramic Hybrid Antifouling Coatings

Simultaneous realization of superior mechanical and antifouling properties is critical for a coating. The use of stereoscopic polysiloxanes in place of linear polysiloxanes to fabricate antifouling coatings can combine properties of organic and inorganic materials, i.e., they can exhibit both high hardness and wear resistance from inorganic components as well as the flexibility and tunability from organic components. This strategy is used to prepare hard yet flexible antifouling coatings or polymer-ceramic hybrid antifouling coatings. In this mini-review, we report the recent advances in this field. Particularly, the effects of stereoscopic polysiloxane structures on their mechanical and antifouling properties are discussed in detail.

Unraveling the Intrinsic Biocidal Activity of the SiO2-Ag Composite against SARS-CoV-2: A Joint Experimental and Theoretical Study

The COVID-19 pandemic has emerged as an unprecedented global healthcare emergency, demanding the urgent development of effective materials to inactivate the SARS-CoV-2 virus. This research was planned to disclose the remarkable biocidal activity of SiO2-Ag composites incorporated into low-density polyethylene. For this purpose, a joint experimental and theoretical [based on first-principles calculations at the density functional theory (DFT) level] study is performed. Biological assays showed that this material eliminatesStaphylococcus aureusand SARS-CoV-2 virus in just 2 min. Here, we investigate a previously unexplored process that we postulate may occur along the O2 and H2O adsorption and activation processes of pure and defective SiO2-Ag surfaces for the generation of reactive oxygen species (ROS). The obtained results help us to predict the nature of ROS: superoxide anion radicals, •O2-, hydroxyl radicals, •OH, and hydroperoxyl radicals, •HO2, that destroy and degrade the structure of the SARS-COV-2 virus. This is consistent with the DFT studies, where the energetic, electronic, and magnetic properties of the intermediates show a feasible formation of ROS. Present findings are expected to provide new insights into the relationship among the structure, property, and biocidal activity of semiconductor/metal SiO2-Ag composites.

Transparent, Robust, and Photochemical Antibacterial Surface Based on Hydrogen Bonding between a Si-Al and Cationic Dye

Healthcare-associated infections can occur and spread through direct contact with contaminated fomites in a hospital, such as mobile phones, tablets, computer keyboards, doorknobs, and other surfaces. Herein, this study shows a transparent, robust, and visible light-activated antibacterial surface based on hydrogen bonds between a transparent silica-alumina (Si-Al) sol-gel and a visible light-activated photosensitizer, such as crystal violet (CV). The study of the bonding mechanisms revealed that hydrogen bonding predominantly occurs between the N of CV and Al-OH. Apart from CV, Si-Al can be combined with a variety of dyes, highlighting its potential for wide application. The Si-Al@CV film selectively generates singlet oxygen using ambient visible light, triggering potent photochemical antibacterial performance against Gram-positive and Gram-negative bacteria. Additionally, the Si-Al@CV film is stable even after mechanical stability tests such as tape adhesion, scratch, bending, and water immersion. In vitro cytotoxicity tests using C2C12 myoblast cells showed that the Si-Al@CV film is a biocompatible material. This work suggests a new approach for designing a transparent and robust touchscreen surface with photochemical antibacterial capability against healthcare-associated infections.

Inactivation of SARS-CoV-2 and Other Human Coronaviruses Aided by Photocatalytic One-Dimensional Titania Nanotube Films as a Self-Disinfecting Surface

SARS-CoV-2 and its variants that continue to emerge have necessitated the implementation of effective disinfection strategies. Developing self-disinfecting surfaces can be a potential route for reducing fomite transmissions of infectious viruses. We show the effectiveness of TiO₂ nanotubes (T_NTs) on photocatalytic inactivation of human coronavirus, HCoV-OC43, as well as SARS-CoV-2. T_NTs were synthesized by the anodization process, and their impact on photocatalytic inactivation was evaluated by the detection of residual viral genome copies (quantitative real-time quantitative reverse transcription polymerase chain reaction) and infectious viruses (infectivity assays). T_NTs with different structural morphologies, wall thicknesses, diameters, and lengths were prepared by varying the time and applied potential during anodization. The virucidal efficacy was tested under different UV-C exposure times to understand the photocatalytic reaction's kinetics. We showed that the T_NT presence boosts the inactivation process and demonstrated complete inactivation of SARS-CoV-2 as well as HCoV-OC43 within 30 s of UV-C illumination. The remarkable cyclic stability of these T_NTs was revealed through a reusability experiment. The spectroscopic and electrochemical analyses have been reported to correlate and quantify the effects of the physical features of T_NT with photoactivity. We anticipate that the proposed one-dimensional T_NT will be applicable for studying the surface inactivation of other coronaviruses including SARS-CoV-2 variants due to similarities in their genomic structure.

ALD-induced TiO2/Ag nanofilm for rapid surface photodynamic ion sterilization

The daily life of people in the intelligent age is inseparable from electronic device, and a number of bacteria on touch screens are increasingly threatening the health of users. Herein, a photocatalytic TiO₂/Ag thin film was synthesized on a glass by atomic layer deposition and subsequent in situ reduction. Ultraviolet-visible (UV-Vis) spectra showed that this film can harvest the simulated solar light more efficiently than that of pristine TiO₂. The antibacterial tests in vitro showed that the antibacterial efficiency of the TiO₂/Ag film against S. aureus and E. coli was 98.2% and 98.6%, under visible light irradiation for 5 min. The underlying mechanism was that the in-situ reduction of Ag on the surface of TiO₂ reduced the bandgap of TiO₂ from 3.44 to 2.61 eV due to the formation of Schottky heterojunction at the interface between TiO₂ and Ag. Thus, TiO₂/Ag can generate more reactive oxygen species for bacterial inactivation on the surface of electronic screens. More importantly, the TiO₂/Ag film had great biocompatibility with/without light irradiation. The platform not only provides a more convenient choice for the traditional antibacterial mode but also has limitless possibilities for application in the field of billions of touch screens.

Ag2O Nanoparticles as a Candidate for Antimicrobial Compounds of the New Generation

Antibiotic resistance in microorganisms is an important problem of modern medicine which can be solved by searching for antimicrobial preparations of the new generation. Nanoparticles (NPs) of metals and their oxides are the most promising candidates for the role of such preparations. In the last few years, the number of studies devoted to the antimicrobial properties of silver oxide NPs have been actively growing. Although the total number of such studies is still not very high, it is quickly increasing. Advantages of silver oxide NPs are the relative easiness of production, low cost, high antibacterial and antifungal activities and low cytotoxicity to eukaryotic cells. This review intends to provide readers with the latest information about the antimicrobial properties of silver oxide NPs: sensitive organisms, mechanisms of action on microorganisms and further prospects for improving the antimicrobial properties.

Effect of Surface Porosity on SARS-CoV-2 Fomite Infectivity

Previous reports indicated the low stability of severe actute respiratory syndrome coronovirus 2 (SARS-CoV-2) on various porous surfaces, but the role of porosity was unclear because there was no direct comparison between porous and nonporous solids of the same chemistry. Through comparing pairs of solids with very similar chemistry, we find that porosity is important: porous glass has a much lower infectivity than nonporous glass. However, porosity is not sufficient to lower infectivity; permeability, which is the ability of a liquid to move through a material, is the important parameter. We show this by comparing a pair of porous CuO coatings where the pores are accessible in one case and inaccessible in the other case. When the pores are inaccessible, the infectivity remains similar to that for nonporous solids. Thus, for both glass and CuO, it is the access to porosity that decreases the infectivity of extracted liquid droplets. Having established the importance of permeability, there is the open question of the mechanism of changing the infectivity of SARS-CoV-2. Several hypotheses are possible, such as increasing the difficulty of extracting the virus from the solid, changing the drying time, increasing the surface area of active ingredient, etc. Reverse transcriptase quantitative polymerase chain reaction (RT-qPCR) measurements show that less viral DNA is extracted from a permeable surface, suggesting that the virus becomes trapped in the pores. Finally, we consider the effect of drying. We show that permeability and the water contact angle on the solid have effects on the drying time of a contaminated droplet, which may in turn affect infectivity.