Highly Active Hydrogen Evolution Electrodes via Co-Deposition of Platinum and Polyoxometalates

Designing a hybrid nanomaterial based on Cr-containing polyoxometalate and graphene oxide as an electrocatalyst for the hydrogen evolution reaction

A new polyoxometalate (POM)-based hybrid nanomaterial (denoted as PMo11-Cr-mGO) was designed via covalent interaction between the Cr(acac)3 complex and [PMo11O39]7- followed by immobilization on the surface of modified graphene oxide (mGO). The prepared nanomaterial was characterized using a series of physicochemical techniques. X-ray diffraction (XRD), Raman analysis, transmission electron microscopy (TEM), and FE-SEM-EDS revealed the preservation of layered GO during the formation of the desired hybrid nanomaterial. Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), and elemental analysis confirmed the immobilization of POM (PMo11-Cr) on the surface of mGO and the formation of PMo11-Cr-mGO. In order to evaluate the performance of PMo11-Cr-mGO in the hydrogen evolution reaction (HER), electrochemical measurements were also performed. The resulting PMo11-Cr-mGO exhibited excellent HER activities with a low overpotential of 153 mV at 10 mA cm-2 and good durability in acidic media, thus emerging as one of the most efficient POM-based electrocatalysts.

Layer-by-Layer Construction of a Nanoarchitecture by Polyoxometalates and Polymers: Enhanced Electrochemical Hydrogen Evolution Reaction

In this contribution, a nanoarchitectural approach was employed to produce a nanolayer of polyoxometalate (POM) on the surface of a glassy carbon electrode (GCE) to achieve a higher surface area with higher electrocatalytic activity toward the electrochemical hydrogen evolution reaction (HER). To accomplish this, the well-known layer-by-layer (LbL) technique was employed, which involved the alternate adsorption of the POM, Na_0.3[N(C₄H₉)₄]_7.7 [(Mo₃O₈)₄(O₃PC(O)(C₃H₆NH₂CH₂C₄H₃S)PO₃)₄], abbreviated as [(TBA)Mo₁₂(AleThio)₄], and polyethyleneimine (PEI) polymer. This nanolayered electrode exhibited catalytic properties toward the HER in 0.5 M H₂SO₄ with the resulting polarization curves indicating an increase in the HER activity with the increasing number of POM layers, and the overpotential required for this reaction was lowered by 0.83 V when compared with a bare GCE. The eighth PEI/[(TBA)Mo₁₂(AleThio)₄] bilayer exhibited a significantly lower HER overpotential of -0.077 V at a current density of 10 mA cm^-2. Surface characterization of the LbL-assembled nanolayers was carried out using X-ray photoelectron spectroscopy, atomic force microscopy, and scanning electron microscopy. We believe that the synergetic effect of the positively charged PEI polymer and the catalytically active molybdate POM is the cause for the successful response to the electrochemical HER.

Water electrolysis: from textbook knowledge to the latest scientific strategies and industrial developments

Replacing fossil fuels with energy sources and carriers that are sustainable, environmentally benign, and affordable is amongst the most pressing challenges for future socio-economic development. To that goal, hydrogen is presumed to be the most promising energy carrier. Electrocatalytic water splitting, if driven by green electricity, would provide hydrogen with minimal CO2 footprint. The viability of water electrolysis still hinges on the availability of durable earth-abundant electrocatalyst materials and the overall process efficiency. This review spans from the fundamentals of electrocatalytically initiated water splitting to the very latest scientific findings from university and institutional research, also covering specifications and special features of the current industrial processes and those processes currently being tested in large-scale applications. Recently developed strategies are described for the optimisation and discovery of active and durable materials for electrodes that ever-increasingly harness first-principles calculations and machine learning. In addition, a technoeconomic analysis of water electrolysis is included that allows an assessment of the extent to which a large-scale implementation of water splitting can help to combat climate change. This review article is intended to cross-pollinate and strengthen efforts from fundamental understanding to technical implementation and to improve the 'junctions' between the field's physical chemists, materials scientists and engineers, as well as stimulate much-needed exchange among these groups on challenges encountered in the different domains.

In situ anodic dissolution–cathodic deposition route for preparation of the Pt–SiW11Co/SiW11Co–CNP/GC electrode: application as an efficient electrode for the hydrogen evolution reaction

A novel nanohybrid based on carbon nanoparticles, platinum nanoparticles, and SiW₁₁Co polyoxometalate is introduced as an efficient electrocatalyst for the hydrogen evolution reaction (HER).

Surface Atom Regulation on Polyoxometalate Electrocatalyst for Simultaneous Low-Voltage H2 Production and Phenol Degradation

The electrocatalytic hydrogen evolution reaction is an ideal method for H₂ production. To improve the performance of polyoxometalate-based electrocatalyst in the hydrogen evolution reaction, one O^2- in polyoxometalate is replaced by S^2-. This weakens the binding of polyoxometalate to H*, facilitates its desorption, and improves the H₂ generation property. Vulcanized polyoxometalate only requires 55 mV to achieve 10 mA·cm^-2 current in the hydrogen evolution reaction. This electrocatalyst also exhibits promising performance in phenol degradation reaction, which is an ideal substitute for high-energy-consuming oxygen evolution reaction in H₂ production due to low voltage to drive. To acquire 100 and 200 mA·cm^-2 in the phenol degradation reaction, this vulcanized polyoxometalate only consumes 1.38 and 1.41 V. With this electrocatalyst working as a cathode and an anode simultaneously, an electrolyzer is constructed by employing phenol-containing KOH as an electrolyte. To obtain 100 and 200 mA·cm^-2 current, the electrolyzer only requires 1.54 and 1.57 V. Because energy-efficient phenol degradation reaction occurs, these values are obviously lower than the oxygen evolution reaction involved in the overall water-splitting H₂ production. This work provides a universal method to enhance the hydrogen evolution reaction (HER) activity of polyoxometalates. Furthermore, a new method is explored, which achieves energy conservation and phenol degradation simultaneously in H₂ production.

Best Practice for Evaluating Electrocatalysts for Hydrogen Economy

Screening new electrocatalysts is key to the development of new materials for next-generation energy devices such as fuel cells and electrolyzers. The counter electrodes used in such tests are often made from materials such as Pt and Au, which can dissolve during testing and deposit onto test electrocatalysts, resulting in inaccurate results. The most common strategy for preventing this effect is to separate the counter electrode from the test material using an ion-transporting Nafion membrane. Here, we use X-ray photoelectron spectroscopy, energy-dispersive X-ray analysis, mass spectrometry, and voltammetry to demonstrate the limitations of this approach during constant-current, extended stability testing of electrocatalysts for H₂ evolution. We show that Nafion membranes cannot prevent contamination of carbon electrocatalysts by Pt and Au counter electrodes, leading to an apparent increase in the electrocatalytic activity of the carbon. We then demonstrate that carbon counter electrodes in undivided cells can contaminate and deactivate Pt and Au electrocatalysts for H₂ evolution. We show that use of a setup composed of a glass frit separating a carbon counter electrode from the test electrocatalyst can prevent these effects. Finally, we discuss these phenomena using H₂ evolution at MoS₂ and at a K₆[P₂W₁₈O₆₂](H₂O)₁₄/carbon nanotube composite as test reactions.

Polyoxometalates in dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) are the third generation of photovoltaic cells developed by Grätzel and O'Regan. They have the characteristics of low cost, simple manufacturing process, tunable optical properties, and higher photoelectric conversion efficiency (PCE). With an ever increasing energy crisis, there is an urgent need to develop highly efficient, environmentally benign, and energy-saving cell materials. Polyoxometalates (POMs), a kind of molecular inorganic quasi-semiconductor, are promising candidates for use in different parts of DSSCs due to their excellent photosensitivity, redox, and catalytic properties, as well as their relative stability. Following a brief introduction to the development of DSSCs and the potential virtues of POMs in DSSCs, we attempt to make some generalizations about the energy level regulation of POMs that is the underlying theoretical basis for their application in DSSCs, and then we summarize the research progress of POMs in DSSCs in recent years. This is organized in terms of the properties of POMs, namely, electron acceptor, photosensitivity, redox and catalysis, based on the accumulation of our research into POMs over many years. Meanwhile, in view of the fact that the properties of POMs depend primarily on their electronic structural diversity, we keep this point in mind throughout the article with a view to revealing their structure-property relationships. Finally we provide a short summary and remarks on the future outlook. This review may be of interest to synthetic chemists devoted to designing POMs with specific structures, and researchers engaged in the extension of POMs to photoelectric materials.

Low-Loading of Pt Nanoparticles on 3D Carbon Foam Support for Highly Active and Stable Hydrogen Production

Minimizing Pt loading is essential for designing cost-effective water electrolyzers and fuel cell systems. Recently, three-dimensional macroporous open-pore electroactive supports have been widely regarded as promising architectures to lower loading amounts of Pt because of its large surface area, easy electrolyte access to Pt sites, and superior gas diffusion properties to accelerate diffusion of H₂ bubbles from the Pt surface. However, studies to date have mainly focused on Pt loading on Ni-based 3D open pore supports which are prone to corrosion in highly acidic and alkaline conditions. Here, we investigate electrodeposition of Pt nanoparticles in low-loading amounts on commercially available, inexpensive, 3D carbon foam (CF) support and benchmark their activity and stability for electrolytic hydrogen production. We first elucidate the effect of deposition potential on the Pt nanoparticle size, density and subsequently its coverage on 3D CF. Analysis of the Pt deposit using scanning electron microscopy images reveal that for a given deposition charge density, the particle density increases (with cubic power) and particle size decreases (linearly) with deposition overpotential. A deposition potential of -0.4 V vs. standard calomel electrode (SCE) provided the highest Pt nanoparticle coverage on 3D CF surface. Different loading amounts of Pt (0.0075-0.1 mg_Pt/cm²) was then deposited on CF at -0.4 V vs. SCE and subsequently studied for its hydrogen evolution reaction (HER) activity in acidic 1M H₂SO₄ electrolyte. The Pt/CF catalyst with loading amounts as low as 0.06 mg_Pt/cm² (10-fold lower than state-of-the-art commercial electrodes) demonstrated a mass activity of 2.6 ampere per milligram Pt at 200 mV overpotential, nearly 6-fold greater than the commercial Pt/C catalyst tested under similar conditions. The 3D architectured electrode also demonstrated excellent stability, showing <7% loss in activity after 60 h of constant current water electrolysis at 100 mA/cm².

Pristine Metal-Organic Frameworks and their Composites for Energy Storage and Conversion

Metal-organic frameworks (MOFs), a new class of crystalline porous organic-inorganic hybrid materials, have recently attracted increasing interest in the field of energy storage and conversion. Herein, recent progress of MOFs and MOF composites for energy storage and conversion applications, including photochemical and electrochemical fuel production (hydrogen production and CO₂ reduction), water oxidation, supercapacitors, and Li-based batteries (Li-ion, Li-S, and Li-O₂ batteries), is summarized. Typical development strategies (e.g., incorporation of active components, design of smart morphologies, and judicious selection of organic linkers and metal nodes) of MOFs and MOF composites for particular energy storage and conversion applications are highlighted. A broad overview of recent progress is provided, which will hopefully promote the future development of MOFs and MOF composites for advanced energy storage and conversion applications.

Electrocatalytic performance of ultrasmall Mo2C affected by different transition metal dopants in hydrogen evolution reaction

Molybdenum carbides are considered as one type of privileged noble-metal-free electrocatalysts for hydrogen evolution reactions (HER) due to their d-band electron structure, which is similar to Pt. Especially, the electronic structure of such materials can be further adjusted by elemental doping to improve their electrocatalytic activity. Herein, we selected the Anderson-type polyoxometalates (POMs) (NH4)n[TMMo6O24H6]·5H2O (TM = Ni2+, Co2+, n = 4; TM = Fe3+, Cr3+, n = 3) as precursors to prepare new transition-metal-doped Mo2C materials. When these POMs were mixed with dicyandiamide (DCA) by solid grinding, and carbonized at a high temperature, a series of Ni-, Co-, Fe-, and Cr-doped Mo2C composite nanoparticles covered by few-layer graphitic carbon shells (abbr. TM-Mo2C@C) were obtained. All these nanoparticles possess a similar size, morphology, and TM/Mo component ratio, and thus it is feasible to systematically investigate the influence of different TM dopants on the electrocatalytic activity of Mo2C for HER. Both electrocatalytic experiments and DFT calculations reveal that TM dopants have a significant effect on the hydrogen binding energy (ΔGH*) and the catalytic activity of Mo2C. The sequence of HER electrocatalytic activity is as follows: Ni-Mo2C > Co-Mo2C > Fe-Mo2C > Cr-Mo2C. As a result, Ni-Mo2C@C possesses the best HER performance, which required an overpotential of 72 mV at a current density of 10 mA cm-2 and the Tafel slope is 65.8 mV dec-1. This work suggests a shortcut to reasonably investigate the effects of elemental doping on molybdenum carbides and explore new high-efficient and low-cost electrocatalysts for HER.

Tuning the Composition and Structure of Amorphous Molybdenum Sulfide/Carbon Black Nanocomposites by Radiation Technique for Highly Efficient Hydrogen Evolution

Amorphous molybdenum sulfide/carbon black (MoS_x/C) nanocomposites are synthesized by a facile one-step γ-ray radiation induced reduction process. Amorphous MoS_x shows better intrinsic activity than crystalline MoS₂. And the composition and amorphous structure of MoS_x could be expediently tuned by absorbed dose for excellent catalytic activity. Meanwhile, the addition of carbon black leads to a significant decrease of charge transfer resistance and increase of active sites of MoS_x/C composite. Consequently, MoS_x/C nanocomposite shows Pt-like catalytic activity towards hydrogen evolution reaction (HER), which requires an onset over potential of 40 mV and over potential of 76 mV to achieve a current density of 10 mA cm⁻², and the corresponding Tafel slope is 48 mV decade⁻¹. After 6000 CV cycles, the catalytic activity of MoS_x/C shows no obvious decrease. However, when platinum (Pt) foil is used as counter electrode, MoS_x/C composite show better catalytic activity abnormally after long-term cycling tests. The dissolution of Pt was observed in HER and the Pt dissolution mechanism is elucidated by further analyzing the surface composition of after-cycling electrodes, which offers highly valuable guidelines for using Pt electrode in HER.

Three-Dimensional Dendritic Structures of NiCoMo as Efficient Electrocatalysts for the Hydrogen Evolution Reaction

First-row (3d) transition-metal catalysts, such as bimetallic Ni-Co, represent an emerging class of electrocatalysts for HER, but they usually suffer from a large overpotential significantly above thermodynamic demands. Here, we doped NiCo catalyst with non3d metals molybdenum (Mo) for improvement in catalyzing the hydrogen evolution reaction. The ternary catalyst was readily obtained by a one-pot process via the sequential electrodeposition of Ni, Co, and Mo precursors on titanium (Ti) support. By tailing the deposition conditions, we fabricated NiCoMo catalysts with three-dimensional dendritic structures, exhibiting large amounts of electrochemically active sites. To attain the benchmark HER current density of -10 mA cm^-2, an overpotential of ∼132 mV is required in 0.1 M KOH for the Mo-doped NiCo (5 atom % Mo in bath), and they produced the decreasing in Tafel slope of ∼108 mV decade^-1 exceeding those of binary NiCo alloy catalysts and other contents of Mo doping. In a synergistic effect, dopant incorporation of Mo element may provide near-optimal adsorption energies for HER intermediates promoting the process of water dissociation and hydrogen intermediates production and binding into molecular hydrogen.

Hierarchical MoS2@MoP core-shell heterojunction electrocatalysts for efficient hydrogen evolution reaction over a broad pH range

A low-cost catalyst for the hydrogen evolution reaction (HER) over a broad pH range is highly desired to meet the practical needs in different areas. In this study, hierarchical flower-like MoS2@MoP core-shell heterojunctions (HF-MoSP) are designed as a promising catalyst for HER over a broad pH range. The materials are obtained by the controllable phosphidation of the hierarchical MoS2 flower (HF-MoS2) composed of thin silk belt-like sheets. The phosphidation degree, P/S ratio and work function (WF) of HF-MoSP can be tuned easily over broad range by changing the phosphidation temperature. Under optimized condition, HF-MoSP exhibits excellent electrocatalytic activity for HER with a low onset overpotential of 29 mV and η of 108 mV at 10 mA cm(-2) in 0.5 M H2SO4 and retains its good activity for 30 h. In addition, the catalyst shows excellent activity in 1 M KOH with an onset overpotential of 42 mV and η of 119 mV at 10 mA cm(-2). The catalysts also exhibit obvious activity in neutral, weak acid and weak alkaline conditions. The good performance is relative to the synergy of the MoP shell and MoS2 core and the high WF of HF-MoSP close to Pt, and the large SBET of HF-MoSP benefited from the hierarchical structure. This study represents the construction of the core-shell heterojunction and provides a new way to provide the low-cost and high-performance catalyst for HER.

An electrochemical bifunctional sensor for the detection of nitrite and hydrogen peroxide based on layer-by-layer multilayer films of cationic phthalocyanine cobalt(ii) and carbon nanotubes

Binder-free multilayer films composed of phthalocyanine and carbon nanotubes were constructed by the layer-by-layer electrostatic assembly and applied for the electrochemical detection of NO₂⁻ and H₂O₂.

An efficient ultra-thin chain-structured copper cobalt oxide/sulfide composite catalyst for electrochemical hydrogen generation

An ultra-thin chain-structured copper cobalt oxide/sulfide composite catalyst was prepared by hydrothermal method for HER.