Inverted Planar Perovskite Solar Cells with a High Fill Factor and Negligible Hysteresis by the Dual Effect of NaCl-Doped PEDOT:PSS

Suppressing Oxidation at Perovskite-NiOx Interface for Efficient and Stable Tin Perovskite Solar Cells

Inorganic nickel oxide (NiOx) is an ideal hole transport material (HTM) for the fabrication of high-efficiency, stable, and large-area perovskite photovoltaic devices because of its low cost, stability, and ease of solution processing. However, it delivers low power conversion efficiency (PCE) in tin perovskite solar cells (TPSCs) compared to other organic HTMs. Here, the origin of hole transport barriers at the perovskite-NiOx interface is identified and a self-assembled monolayer interface modification is developed, through introducing (4-(7H-dibenzo[c,g]carbazol-7-yl)ethyl)phosphonic acid (2PADBC) into the perovskite-NiOx interface. The 2PADBC anchors undercoordinated Ni cations through phosphonic acid groups, suppressing the reaction of highly active Ni≥3+ defects with perovskites, while increasing the electron density and oxidation activation energy of Sn at the perovskite interface, reducing the interface nonradiative recombination caused by tetravalent Sn defects. The devices deliver significantly increased open-circuit voltage from 0.712 to 0.825 V, boosting the PCE to 14.19% for the small-area device and 12.05% for the large-area (1 cm2) device. In addition, the 2PADBC modification enhances the operational stability of NiOx-based TPSCs, maintaining more than 93% of their initial efficiency after 1000 h.

Development on inverted perovskite solar cells: A review

Recently, inverted perovskite solar cells (IPSCs) have received note-worthy consideration in the photovoltaic domain because of its dependable operating stability, minimal hysteresis, and low-temperature manufacture technique in the quest to satisfy global energy demand through renewable means. In a decade transition, perovskite solar cells in general have exceeded 25 % efficiency as a result of superior perovskite nanocrystalline films obtained via low temperature synthesis methods along with good interface and electrode materials management. This review paper presents detail processes of refining the stability and power conversion efficiencies in IPSCs. The latest development in the power conversion efficiency, including structural configurations, prospect of tandem solar cells, mixed cations and halides, films' fabrication methods, charge transport material alterations, effects of contact electrode materials, additive and interface engineering materials used in IPSCs are extensively discussed. Additionally, insights on the state of the art and IPSCs' continued development towards commercialization are provided.

Novel Spiro-Core Dopant-Free Hole Transporting Material for Planar Inverted Perovskite Solar Cells

Hole-transporting materials (HTMs) have demonstrated their crucial role in promoting charge extraction, interface recombination, and device stability in perovskite solar cells (PSCs). Herein, we present the synthesis of a novel dopant-free spiro-type fluorine core-based HTM with four ethoxytriisopropylsilane groups (Syl-SC) for inverted planar perovskite solar cells (iPSCs). The thickness of the Syl-SC influences the performance of iPSCs. The best-performing iPSC is achieved with a 0.8 mg/mL Syl-SC solution (ca. 15 nm thick) and exhibits a power conversion efficiency (PCE) of 15.77%, with J_sc = 20.00 mA/cm², V_oc = 1.006 V, and FF = 80.10%. As compared to devices based on PEDOT:PSS, the iPSCs based on Syl-SC exhibit a higher V_oc, leading to a higher PCE. Additionally, it has been found that Syl-SC can more effectively suppress charge interfacial recombination in comparison to PEDOT:PSS, which results in an improvement in fill factor. Therefore, Syl-SC, a facilely processed and efficient hole-transporting material, presents a promising cost-effective alternative for inverted perovskite solar cells.

Chemical Bridge-Mediated Heterojunction Electron Transport Layers Enable Efficient and Stable Perovskite Solar Cells

Perovskite solar cells (PSCs) emerged as potential photovoltaic energy-generating devices developing in recent years because of their excellent photovoltaic properties and ease of processing. However, PSCs are still reporting efficiencies much lower than their theoretical limits owing to various losses caused by the charge transport layer and the perovskite. In this regard, herein, an interface engineering strategy using functional molecules and chemical bridges was applied to reduce the loss of the heterojunction electron transport layer. As a functional interface layer, ethylenediaminetetraacetic acid (EDTA) was introduced between PCBM and the ZnO layer, and as a result, EDTA simultaneously formed chemical bonds with PCBM and ZnO to serve as a chemical bridge connecting the two. DFT and chemical analyses revealed that EDTA can act as a chemical bridge between PCBM and ZnO, passivate defect sites, and improve charge transfer. Optoelectrical analysis proved that EDTA chemical bridge-mediated charge transfer (CBM-CT) provides more efficient interfacial charge transport by reducing trap-assisted recombination losses at ETL interfaces, thereby improving device performance. The PSC with EDTA chemical bridge-mediated heterojunction ETL exhibited a high PCE of 21.21%, almost no hysteresis, and excellent stability to both air and light.

Seeding Agents in Metal Halide Perovskite Solar Cells: From Material to Mechanism

Metal halide perovskite solar cells (PSCs) have been showing up in the commercial field, with an inspiring power conversion efficiency (PCE) of over 26 % in the laboratory. The quality of perovskite films is still a bottleneck due to the random and fast crystallization of ionic perovskite materials. Seeding agent-mediated crystallization has consistently been recognized as an efficient method for preparing bulk single crystals and high-quality films. Herein, we summarized the seeding mechanism, characterization techniques, and seeding agents working in different locations during PSC device fabrication. This Review could further facilitate researchers with a deeper understanding of seeding agents and enhance more choices for seeding crystallization to improve the performance further and the device's large-scale fabrication toward commercialization.

Enhancement in Power Conversion Efficiency of Perovskite Solar Cells by Reduced Non-Radiative Recombination Using a Brij C10-Mixed PEDOT:PSS Hole Transport Layer

Interface properties between charge transport and perovskite light-absorbing layers have a significant impact on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is a polyelectrolyte composite that is widely used as a hole transport layer (HTL) to facilitate hole transport from a perovskite layer to an anode. However, PEDOT:PSS must be modified using a functional additive because PSCs with a pristine PEDOT:PSS HTL do not exhibit a high PCE. Herein, we demonstrate an increase in the PCE of PSCs with a polyethylene glycol hexadecyl ether (Brij C10)-mixed PEDOT:PSS HTL. Photoelectron spectroscopy results show that the Brij C10 content becomes significantly high in the HTL surface composition with an increase in the Brij C10 concentration (0-5 wt%). The enhanced PSC performance, e.g., a PCE increase from 8.05 to 11.40%, is attributed to the reduction in non-radiative recombination at the interface between PEDOT:PSS and perovskite by the insulating Brij C10. These results indicate that the suppression of interface recombination is essential for attaining a high PCE for PSCs.

Stability of perovskite solar cells: issues and prospects

Even though power conversion efficiency has already reached 25.8%, poor stability is one of the major challenges hindering the commercialization of perovskite solar cells (PSCs). Several initiatives, such as structural modification and fabrication techniques by numerous ways, have been employed by researchers around the world to achieve the desired level of stability. The goal of this review is to address the recent improvements in PSCs in terms of structural modification and fabrication procedures. Perovskite films are used to provide a broad range of stability and to lose up to 20% of their initial performance. A thorough comprehension of the effect of the fabrication process on the device's stability is considered to be crucial in order to provide the foundation for future attempts. We summarize several commonly used fabrication techniques - spin coating, doctor blade, sequential deposition, hybrid chemical vapor, and alternating layer-by-layer. The evolution of device structure from regular to inverted, HTL free, and ETL including the changes in material utilization from organic to inorganic, as well as the perovskite material are presented in a systematic manner. We also aimed to gain insight into the functioning stability of PSCs, as well as practical information on how to increase their operational longevity through sensible device fabrication and materials processing, to promote PSC commercialization at the end.

How varying surface wettability of different PEDOT:PSS formulations and their mixtures affects perovskite crystallization and the efficiency of inverted perovskite solar cells

The physico-chemical interaction, surface, and electrical properties of hole transport layers (HTLs) significantly affect the wettability and film crystallization of the deposited perovskite and the corresponding performance of inverted perovskite solar cells (PSCs). One of the most frequently used HTLs for inverted PSCs is poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS). Various commercial PEDOT:PSS formulations have already been tested as HTLs. Until now mixtures of these remained rather unexplored. In this study, three commercially available PEDOT:PSS formulations (PH, PH1000, and AI4083), as well as three mixtures (PH:PH1000, PH:AI4083, and PH:PH1000:AI4083; in a 1 : 1 and 1 : 1 : 1 ratios) were used as HTLs to investigate the crystallization of perovskite films and the performance of associated PSCs. Of the three formulations, PEDOT:PSS PH showed better perovskite crystallization, resulting in better solar cell performance followed by both PH:AI4083 and PH:PH1000:AI4083 layers. The pioneering work on mixing PEDOT:PSS resulted in new combinations of PEDOT:PSS, with new properties (work function, surface wettability, and roughness) which are very important parameters for perovskite crystallization and corresponding device efficiencies and stabilities. All PSCs that use the mixed PEDOT:PSS as HTLs revealed higher fill factor and open-circuit voltage values above 900 mV, which is not the same except for PEDOT:PSS PH. As a result, we believe that such a mixing strategy could aid in the creation of various PEDOT:PSS combinations with tuneable properties for certain applications.

Electrochemically Prepared Polyaniline as an Alternative to Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) for Inverted Perovskite Solar Cells

The goal of this work is to substitute the conventional high-cost poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) in inverted perovskite solar cells (PSCs) with an efficient and conducting polyaniline (PANI) polymer. The reported use of PANI in PSCs involves a chemical synthesis method which is prone to contamination with impurities as it requires several materials for polymerization and adhesion improvement with substrates, contributing to low device efficiencies. This work mitigates this issue using an electrochemical method that is low cost, less time consuming, and capable of producing thin films of PANI with excellent adhesion to substrates. Results demonstrated that the power conversion efficiency of the electrochemically synthesized PANI-based PSC is 16.94% versus 15.11% for the PEDOT:PSS-based device. It was observed that the work function of PANI was lower compared to that of PEDOT:PSS which decreased V _OC but enhanced hole extraction at the hole transport layer/perovskite interface, thus increasing J _SC. Doping electrolyte solution with lithium bis(trifluoromethanesulfonyl)imide LiTFSI increased the work function of PANI, thus increasing V _OC from 0.87 to 0.93 V. This method enables simple and scalable synthesis of PANI as a competitive hole transport material to replace rather expensive PEDOT:PSS, thus enabling an important step toward low-cost inverted perovskite photovoltaic devices.

Recent Criterion on Stability Enhancement of Perovskite Solar Cells

Perovskite solar cells (PSCs) have captured the attention of the global energy research community in recent years by showing an exponential augmentation in their performance and stability. The supremacy of the light-harvesting efficiency and wider band gap of perovskite sensitizers have led to these devices being compared with the most outstanding rival silicon-based solar cells. Nevertheless, there are some issues such as their poor lifetime stability, considerable J–V hysteresis, and the toxicity of the conventional constituent materials which restrict their prevalence in the marketplace. The poor stability of PSCs with regard to humidity, UV radiation, oxygen and heat especially limits their industrial application. This review focuses on the in-depth studies of different direct and indirect parameters of PSC device instability. The mechanism for device degradation for several parameters and the complementary materials showing promising results are systematically analyzed. The main objective of this work is to review the effectual strategies of enhancing the stability of PSCs. Several important factors such as material engineering, novel device structure design, hole-transporting materials (HTMs), electron-transporting materials (ETMs), electrode materials preparation, and encapsulation methods that need to be taken care of in order to improve the stability of PSCs are discussed extensively. Conclusively, this review discusses some opportunities for the commercialization of PSCs with high efficiency and stability.

PEDOT:PSS/CuCl Composite Hole Transporting Layer for Enhancing the Performance of 2D Ruddlesden-Popper Perovskite Solar Cells

Poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) is a popular hole transport layer (HTL) in 2D Ruddlesden-Popper (RP) perovskite solar cell (PSCs) due to its highly conductive, transparent, and solution-processable characteristics. However, fundamental questions such as its strong acidity or mismatched energy level with the 2D RP photoactive layer often restrict the performance and stability of devices. Herein, copper chloride (CuCl), a common direct band gap semiconductor, is doped into PEDOT:PSS, lowering the acidity and tuning the work function of PEDOT:PSS. Due to the improved wettability and the existing chloride in the PEDOT:PSS/CuCl composite substrate, the coated 2D perovskite films exhibit uniform morphology, vertically oriented crystal growth, and enhanced crystallinity. In comparison with controlled devices, the PEDOT:PSS/CuCl based inverted 2D RP PSCs show a maximum power conversion efficiency of 13.36% and long-term stability. The modified PEDOT:PSS overcomes intrinsic imperfections by doping CuCl, indicating that it has a lot of promise for mass production in electrical devices.

Enhanced p-Type Conductivity of NiOx Films with Divalent Cd Ion Doping for Efficient Inverted Perovskite Solar Cells

The effect of substitutional metal dopants in NiO_x on the structural and electronic structures is of great interest, particularly for increasing the p-type conductivities as a hole transport layer (HTL) applied in perovskite solar cells (PSCs). In this paper, experimental fabrications and density functional theory calculations have been carried out on Cd-doped NiO_x films to examine the effect of divalent doping on the electronic and geometric structures of NiO_x. The results indicate that divalent Cd dopants reduced the formation energy of the Ni vacancy (V_Ni) and created more V_Ni in the films, which enhanced the p-type conductivity of the NiO_x films. In addition, Cd doping also deepened the valence band edge, reduced the monomolecular Shockley-Read-Hall (SRH) recombination losses, and promoted hole extraction and transport. Hence, the PSCs with Cd:NiO_x HTLs manifest a high efficiency of 20.47%, a high photocurrent density of 23.00 mA cm^-2, and a high fill factor of 79.62%, as well as negligible hysteresis and excellent stability. This work illustrates that divalent elements such as Cd, Zn, Co, etc. may be potential dopants to improve the p-type conductivity of the NiO_x films for applications in highly efficient and stabilized PSCs.

Simultaneous Interfacial Modification and Crystallization Control by Biguanide Hydrochloride for Stable Perovskite Solar Cells with PCE of 24.4

Interfacial modification, which serves multiple roles, is vital for the fabrication of efficient and stable perovskite solar cells. Here, a multifunctional interfacial material, biguanide hydrochloride (BGCl), is introduced between tin oxide (SnO₂ ) and perovskite to enhance electron extraction, as well as the crystal growth of the perovskite. The BGCl can chemically link to the SnO₂ through Lewis coordination/electrostatic coupling and help to anchor the PbI₂ . Better energetic alignment, reduced interfacial defects, and homogeneous perovskite crystallites are achieved, yielding an impressive certified power conversion efficiency (PCE) of 24.4%, with an open-circuit voltage of 1.19 V and a drastically improved fill factor of 82.4%. More importantly, the unencapsulated device maintains 95% of its initial PCE after aging for over 500 h at 20 °C and 30% relative humidity in ambient conditions. These results suggest that the incorporation of BGCl is a promising strategy to modify the interface and control the crystallization of the perovskite, toward the attainment of highly efficient and stable perovskite solar cells as well as other perovskite-based electronics.

Electrodeposited PEDOT:PSS-Al2O3 Improves the Steady-State Efficiency of Inverted Perovskite Solar Cells

The atomic layer deposition (ALD) of Al₂O₃ between perovskite and the hole transporting material (HTM) PEDOT:PSS has previously been shown to improve the efficiency of perovskite solar cells. However, the costs associated with this technique make it unaffordable. In this work, the deposition of an organic-inorganic PEDOT:PSS-Cl-Al₂O₃ bilayer is performed by a simple electrochemical technique with a final annealing step, and the performance of this material as HTM in inverted perovskite solar cells is studied. It was found that this material (PEDOT:PSS-Al₂O₃) improves the solar cell performance by the same mechanisms as Al₂O₃ obtained by ALD: formation of an additional energy barrier, perovskite passivation, and increase in the open-circuit voltage (V_oc) due to suppressed recombination. As a result, the incorporation of the electrochemical Al₂O₃ increased the cell efficiency from 12.1% to 14.3%. Remarkably, this material led to higher steady-state power conversion efficiency, improving a recurring problem in solar cells.

Review on Tailoring PEDOT:PSS Layer for Improved Device Stability of Perovskite Solar Cells

Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has high optical transparency in the visible light range and low-temperature processing condition, making it one of the most widely used polymer hole transport materials inverted perovskite solar cells (PSCs), because of its high optical transparency in the visible light range and low-temperature processing condition. However, the stability of PSCs based on pristine PEDOT:PSS is far from satisfactory, which is ascribed to the acidic and hygroscopic nature of PEDOT:PSS, and property differences between PEDOT:PSS and perovskite materials, such as conductivity, work function and surface morphology. This review summaries recent efficient strategies to improve the stability of PEDOT:PSS in PSCs and discusses the underlying mechanisms. This review is expected to provide helpful insights for further increasing the stability of PSCs based on commercial PEDOT:PSS.

Performance Comparison between the Nanoporous NiO x Layer and NiO x Thin Film for Inverted Perovskite Solar Cells with Long-Term Stability

The development of hole-transport layers (HTLs) that elevate charge extraction, improve perovskite crystallinity, and decrease interfacial recombination is extremely important for enhancing the performance of inverted perovskite solar cells (PSCs). In this work, the nanoporous nickel oxide (NiO _x ) layer as well as NiO _x thin film was prepared via chemical bath deposition as the HTL. The sponge-like structure of the nanoporous NiO _x helps to grow a pinhole-free perovskite film with a larger grain size compared to the NiO _x thin film. The downshifted valence band of the nanoporous NiO _x HTL can improve hole extraction from the perovskite absorbing layer. The device based on the nanoporous NiO _x layer showed the highest efficiency of 13.43% and negligible hysteresis that was better than the one using the NiO _x thin film as the HTL. Moreover, the PSCs sustained 80% of their initial efficiency after 50 days of storage. This study provides a powerful strategy to design PSCs with high efficiency and long-term stability for future production.

A Review on Emerging Efficient and Stable Perovskite Solar Cells Based on g-C3N4 Nanostructures

Perovskite solar cells (PSCs) have attracted great research interest in the scientific community due to their extraordinary optoelectronic properties and the fact that their power conversion efficiency (PCE) has increased rapidly in recent years, surpassing other 3rd generation photovoltaic (PV) technologies. Graphitic carbon nitride (g-C3N4) presents exceptional optical and electronic properties and its use was recently expanded in the field of PSCs. The addition of g-C3N4 in the perovskite absorber and/or the electron transport layer (ETL) resulted in PCEs exceeding 22%, mainly due to defects passivation, improved conductivity and crystallinity as well as low charge carriers' recombination rate within the device. Significant performance increase, including stability enhancement, was also achieved when g-C3N4 was applied at the PSC interfaces and the observed improvement was attributed to its wetting (hydrophobic/hydrophilic) nature and the fine tuning of the corresponding interface energetics. The current review summarizes the main innovations for the incorporation of graphitic carbon nitride in PSCs and highlights the significance and perspectives of the g-C3N4 approach for emerging highly efficient and robust PV devices.

Recent Progress of Inverted Perovskite Solar Cells with a Modified PEDOT:PSS Hole Transport Layer

Organic-inorganic hybrid perovskite solar cells (PSCs) has achieved the power conversion efficiency (PCE) of 25.2% in the last 10 years, and the PCE of inverted PSCs has reached >22%. The rapid enhancement has partly benefited from the employment of suitable hole transport layers. Especially, poly(3,4-ethenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is one of the most widely used polymer hole transport materials in inverted PSCs, because of its high optical transparency in the visible region and low-temperature processing condition. However, the PCE and stability of PSCs based on pristine PEDOT:PSS are far from satisfactory, which are ascribed to low fitness between PEDOT:PSS and perovskite materials, in terms of work function, conductivity, film growth, and hydrophobicity. This paper summaries recent progress regarding to modifying/remedy the drawbacks of PEDOT:PSS to improve the PCE and stability. The systematically understanding of the mechanism of modified PEDOT:PSS and various characteristic methods are summarized here. This Review has the potential to guide the development of PSCs based on commercial PEDOT:PSS.

Molecular Lock Induced by Chloroplatinic Acid Doping of PEDOT:PSS for High-Performance Organic Photovoltaics

In organic photovoltaics (OPVs), the mechanical contact between charge transport layers and photoactive layer can influence the electrical contact that facilitates carrier collection. Unfortunately, the mechanical contact at the interface is rarely discussed in the OPV context. Herein, we report a distinct molecular locking effect that occurs between the donor molecules in the photoactive layer and the hole transport layer (HTL). This is achieved by doping chloroplatinic acid into poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate). The "molecular lock" at the interface leads to denser distribution and more ordered assembling of PM6 donor molecules close to the HTL. Consequently, the trap-assisted recombination in the cell is greatly suppressed, and the carrier lifetime is prolonged by more than 2 times. Together with the elevated charge carrier collection probability, a high fill factor of 77% and a power conversion efficiency of 16.5% are achieved in the PM6:Y6-based OPVs. This study provides a feasible way to boost the device performance by reinforcing the interfacial interaction between the HTL and photoactive layer.

In Situ Growth of All-Inorganic Perovskite Single Crystal Arrays on Electron Transport Layer

Directly growing perovskite single crystals on charge carrier transport layers will unravel a promising route for the development of emerging optoelectronic devices. Herein, in situ growth of high-quality all-inorganic perovskite (CsPbBr3) single crystal arrays (PeSCAs) on cubic zinc oxide (c-ZnO) is reported, which is used as an inorganic electron transport layer in optoelectronic devices, via a facile spin-coating method. The PeSCAs consist of rectangular thin microplatelets of 6-10 µm in length and 2-3 µm in width. The deposited c-ZnO enables the formation of phase-pure and highly crystallized cubic perovskites via an epitaxial lattice coherence of (100)CsPbBr3∥(100)c-ZnO, which is further confirmed by grazing incidence wide-angle X-ray scattering. The PeSCAs demonstrate a significant structural stability of 26 days with a 9 days excellent photoluminescence stability in ambient environment, which is much superior to the perovskite nanocrystals (PeNCs). The high crystallinity of the PeSCAs allows for a lower density of trap states, longer carrier lifetimes, and narrower energetic disorder for excitons, which leads to a faster diffusion rate than PeNCs. These results unravel the possibility of creating the interface toward c-ZnO heterogeneous layer, which is a major step for the realization of a better integration of perovskites and charge carrier transport layers.

Optimizing the component ratio of PEDOT:PSS by water rinse for high efficiency organic solar cells over 16.7

For the state-of-the-art organic solar cells (OSCs), PEDOT:PSS is the most popularly used hole transport material for the conventional structure. However, it still suffers from several disadvantages, such as low conductivity and harm to ITO due to the acidic PSS. Herein, a simple method is introduced to enhance the conductivity and remove the additional PSS by water rinsing the PEDOT:PSS films. The photovoltaic devices based on the water rinsed PEDOT:PSS present a dramatic improvement in efficiency from 15.98% to 16.75% in comparison to that of the untreated counterparts. Systematic characterization and analysis reveal that although part of the PEDOT:PSS is washed away, it still leaves a smoother film and the ratio of PEDOT to PSS is higher than before in the remaining films. It can greatly improve the conductivity and reduce the damage to substrates. This study demonstrates that finely modifying the charge transport materials to improve conductivity and reduce defeats has great potential for boosting the efficiency of OSCs.

Improved Interfacial Crystallization by Synergic Effects of Precursor Solution Stoichiometry and Conjugated Polyelectrolyte Interlayer for High Open-Circuit Voltage of Perovskite Photovoltaic Diodes

The open-circuit voltage (V_oc) of perovskite photovoltaic diodes depends largely on the selection of charge transport layers (CTLs) and surface passivation, which makes it important to understand the physical processes occurring at the interface between the perovskite and a CTL. We provide a direct correlation between V_oc and the interfacial characteristics of perovskites tuned through stoichiometry engineering of precursor solutions and surface modification of the underlying poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) layer. Poor quality interfacial perovskite crystals were observed on top of the PEDOT:PSS layer, resulting in strong interfacial recombination and a low V_oc. In contrast, the growth of the interfacial perovskite crystals was significantly improved by the synergic effects of varying the precursor solution composition and covering the surface with a pH-neutral conjugated polyelectrolyte, poly[2,6-(4,4-bis(potassium butanylsulfonate)-4H-cyclopenta[2,1-b;3,4-b']dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (CPE-K), which possesses potassium ions as counter ions. The influence of the energy-level alignment at the interface on V_oc was also discussed. Our findings highlight that improved perovskite crystallization at the interface can facilitate bulk growth of perovskite grains in the vertical direction and effectively suppress nonradiative surface charge recombination, thus enhancing the short-circuit current and V_oc.

All-vacuum deposited and thermally stable perovskite solar cells with F4-TCNQ/CuPc hole transport layer

Hole transporting layers (HTLs) play a crucial role in the realization of efficient and stable perovskite solar cells (PSCs). Copper phthalocyanine (CuPc) is a promising HTL owing to its thermal stability and favorable band alignment with the perovskite absorber. However, the power conversion efficiency (PCE) of PSCs with a CuPc HTL is still lagging behind highly efficient solar cells. Herein, a p-type tetrafluoro-tetracyanoquinodimethane (F4-TCNQ) is employed as an interlayer between the perovskite and CuPc HTL in all-vacuum deposited PSCs. The F4-TCNQ interlayer improves the conductivity of both MAPbI₃ and CuPc, reduces the shunt pathway and facilitates an efficient photoexcited holes transfer from the valance band of the MAPbI₃ to the LUMO of the F4-TCNQ. Consequently, the best solar cell device with an F4-TCNQ interlayer achieved a PCE of 13.03% with a remarkable improvement in fill factor. Moreover, the device showed superior stability against thermal stress at 85 °C over 250 h and retained ∼95% of its initial efficiency. This work demonstrates a significant step towards all-vacuum deposited perovskite solar cells with high thermal stability.

Air-Stable Lead-Free Perovskite Thin Film Based on CsBi3I10 and Its Application in Resistive Switching Devices

The development of organic-inorganic hybrid perovskite materials has been rapid in recent years; but their applications are limited by the toxicity and stability of the materials. To address these issues in the context of resistive switching devices, an inorganic lead-free perovskite namely CsBi₃I₁₀ is developed. Uniform and pinhole-free CsBi₃I₁₀ thin films can be fabricated by using CsI-rich precursor solution via a facile antisolvent-assisted spin-coating method. The nonvolatile resistive switching devices based on CsBi₃I₁₀ demonstrate a large on/off ratio (10³), reliable retention properties (10⁴ s), and endurance (150 cycles). Conductive atomic force microscopy reveals that the high- and low-resistance states are formed by breaking and formation of conductive filaments in the perovskite thin film. Because of the excellent stability of the CsBi₃I₁₀ perovskite, the devices exhibit no obvious change in resistive switching behavior even after over 2 month storage in an ambient (60% relative humidity) environment. Our work suggests that the all-inorganic lead-free CsBi₃I₁₀ perovskite has great potential in resistive switching memory as well as in other optoelectronic devices where toxicity and stability are a concern.

Bifunctional oxygen evolution and supercapacitor electrode with integrated architecture of NiFe-layered double hydroxides and hierarchical carbon framework

Layered double hydroxide with exchangeable interlayer anions are considered promising electro-active materials for renewable energy technologies. However, the limited exposure of active sites and poor electrical conductivity of hydroxide powder restrict its application. Herein, bifunctional integrated electrode with a 3D hierarchical carbon framework decorated by nickel iron-layered double hydroxides (NiFe-LDH) is developed. A conductive carbon nanowire array is introduced not only to provide enough anchoring sites for the hydroxide, but also affords a continuous pathway for electron transport throughout the entire electrode. The 3D integrated architecture of NiFe-hydroxide and hierarchical carbon framework possesses several beneficial effects including large electrochemical active surfaces, fast electron/mass transport, and enhanced mechanical stability. The as-prepared electrode affords a current density of 10 mA cm^-2 at a low overpotential of 269 mV for oxygen evolution reaction (OER) in 1 M of KOH. It also offers excellent stability with negligible current decline even after 2000 cycles. Besides, density functional theory calculations revealed that the (110) surface of NiFe-LDH is more active than the (003) surface for OER. Furthermore, the electrode possesses promising application prospects in alkaline battery-supercapacitor hybrid devices with a capacity of 178.8 mAh g^-1 (capacitance of 1609.6 F g^-1) at a current density of 0.2 A g^-1. The viability of the as-prepared bifunctional electrode will provide a potential solution for wearable electronics in the near future.

Nuclei position-control and crystal growth-guidance on frozen substrates for high-performance perovskite solar cells

Nucleation and crystal growth are key stages for high-quality perovskite films that dominate the performance of perovskite solar cells. However, the position of nuclei in the films and the orientation of the crystal growth have not yet been intendedly controlled during their fabrication. In this study, we developed a method of spin-coating perovskite films on frozen substrates to control the position of the nuclei and the direction of the crystal growth at the same time. In this way, the position of the crystal nuclei and the growth orientation of the perovskite crystals in the perovskite films can be simultaneously controlled. A high-quality perovskite film with grains spanning vertically the entire film thickness has been obtained using this new method. And an efficient inverted planar solar cell (ITO/PEDOT:PSS/CH₃NH₃PbI₃/PC61BM/BCP/Ag) with the highest power conversion efficiency of 17.14% and open-circuit voltage of 1.14 V has been achieved by using this technique.

High Open-Circuit Voltage of 1.134 V for Inverted Planar Perovskite Solar Cells with Sodium Citrate-Doped PEDOT:PSS as a Hole Transport Layer

Poly(3,4-ethylenedioxythiophene)/polystyrene sulfonate (PEDOT:PSS) plays an important role in inverted planar perovskite solar cells (IPPSCs) as an efficient hole extraction and transfer layer (HTL). The IPPSCs based on PEDOT:PSS normally display inferior performance with a reduced open-circuit voltage. To address this problem, here sodium citrate-doped PEDOT:PSS is adopted as an effective HTL for improving the performance of IPPSCs. Sodium citrate-doped PEDOT:PSS HTL improves the conversion efficiency of IPPSCs from 15.05% of reference cells to 18.39%. The large increase of the open-circuit voltage ( V_OC) from 1.057 to 1.134 V is the main source for this performance enhancement. With the help of characterization analysis of ultraviolet photoelectron spectroscopy, scanning electron microscopy, electrochemical impedance spectroscopy, etc., the higher work function of the doped PEDOT:PSS film and the uniform crystallinity of the perovskite film on it are disclosed as the reasons for the increased V_OC and the consequent performance enhancement.

Planar Perovskite Solar Cells with High Efficiency and Fill Factor Obtained Using Two-Step Growth Process

Hybrid organic-inorganic perovskite solar cells (PSCs) have been regarded as the most promising next-generation photovoltaics (PVs) because of their potential for low-cost fabrication and advances in their development. Superior quality of the photoactive perovskite layer is a main factor for further increasing the PV performance of the organic-inorganic perovskite solar cells (PSCs). Herein, we successfully obtained perovskite with a high crystallinity and large grain size by utilizing excess PbI₂ and SSGP technique and demonstrated a superior PV performance of normal-architecture planar PSCs. The SSGP PSCs with the highest fill factor (FF) reported thus far (83.4%) to our knowledge were obtained without sacrificing other PV parameters. Moreover, a high efficiency of 21.3% (21.6%) with a high FF of 80.0% (81.2%) in forward (reverse) scan was achieved. The unencapsulated SSGP PSCs showed robust continuous light-soaking and thermal stability under harsh characterization conditions. Additionally, we achieved a high efficiency of 20.1% with a negligible hysteresis on the large active area SSGP PSCs (∼1 cm²). The optical properties, efficient carrier extraction, and reduction of recombination loss of the SSGP perovskite significantly contribute to the high PV performance and robust stability of SSGP PSCs.

Furrowed hole-transport layer using argon plasma in an inverted perovskite solar cell

In this study, a novel process was found to be effective using the argon-plasma treatment, in which the ion cluster was used to scour the PEDOT:PSS surface instead of the traditional bombardment method. The photoelectric conversion efficiency of the device reaches 14.8%.

Inverted (p-i-n) perovskite solar cells using a low temperature processed TiO x interlayer

In this article, we present the improvement in device performance and stability as well as reduction in hysteresis of inverted mixed-cation-mixed-halide perovskite solar cells (PSCs) using a low temperature, solution processed titanium oxide (TiO x ) interlayer between [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) and an Al electrode. Upon applying a TiO x interlayer, device resistance was reduced compared to that of the control devices, which results in improved rectification of the characteristic current density-voltage (J-V) curve and improved overall performance of the device. PSCs with the TiO x interlayer show an open-circuit voltage (V oc) of around 1.1 V, current density (J sc) of around 21 mA cm-2, fill factor (FF) of around 72% and enhanced power conversion efficiency (PCE) of 16% under AM1.5 solar spectrum. Moreover, devices with the TiO x interlayer show improved stability compared to devices without the TiO x interlayer. This finding reveals the dual role of the TiO x interlayer in improving device performance and stability.