Single-Crystal Nitrogen-Rich Two-Dimensional Mo5N6 Nanosheets for Efficient and Stable Seawater Splitting

Dynamic Creation of a Local Acid-like Environment for Hydrogen Evolution Reaction in Natural Seawater

Electrolysis of natural seawater driven by renewable energy is practically attractive for green hydrogen production. However, because precipitation initiated by an increase in local pH near to the cathode deactivates catalysts or blocks electrolyzer channels, limited catalysts are capable of operating with untreated, natural seawater (viz., pH 8.2 to 8.3 and ca. 35 g salts L-1); most are used in strongly alkaline or acidic seawater. Here, we report a new natural seawater electrolysis cathode with precipitation-suppression via a Pt/WO2 catalyst to create a dynamically local acid-like environment. The in situ formed hydrogen tungsten bronze (HxWOy) phase via continuous hydrogen insertion from water acts as a proton reservoir. As a result, dynamically stored protons create a local acid-like environment near the Pt active sites. We evidence that this tailored acid-like environment boosts the hydrogen evolution reaction in natural seawater splitting and neutralizes generated OH- species to restrict precipitation formations. Consequently, a long-term stability of >500 h at 100 mA cm-2 was exhibited in direct seawater electrolysis.

Harvesting Green Hydrogen from the Deep Blue: Seawater-Compatible SnSe-P Decorated Graphene-CNTs Based Electrocatalyst Under Universal pH

Fabrication of cost-effective and robust metal-based electrocatalysts for hydrogen evolution reactions (HER) across the entire pH range has garnered significant attention in harvesting renewable energy. Herein, the fabrication of 3D high-surface Ni Foam-Graphene-Carbon Nanotubes (NGC) decorated with phosphorous-inserted tin selenide (SnSe-P) showcases unprecedented HER activity with minimal overpotentials across all pH ranges (52 mV in acidic, 93 mV in basic, and 198 mV in neutral conditions@10 mA cm-2) and stability at 1 A cm-2 for 72 h. The as-designed catalyst shows a low overpotential of 122 mV@10 mA cm-2 in alkaline seawater, achieved through controlled electronic distribution on Sn site after incorporation of P in NGC-SnSe-P. A stable cell voltage of 1.56 V@10 mA cm⁻2 is achieved for prolonged time in 1 m KOH toward overall water electrolysis. Experimental and theoretical investigation reveals that the insertion of P in layered SnSe enables s orbitals of H* and p orbitals of Sn to interact, favoring the adsorption of the H* intermediate. A renewable approach is adopted by using silicon solar cells (η = 10.66%) to power up the electrolyzer, yielding a solar-to-hydrogen (STH) conversion efficiency of 7.70% in 1 m KOH and 5.65% in alkaline seawater, aiming toward green hydrogen production.

Long-term Durability of Seawater Electrolysis for Hydrogen: From Catalysts to Systems

Direct electrochemical seawater splitting is a renewable, scalable, and potentially economic approach for green hydrogen production in environments where ultra-pure water is not readily available. However, issues related to low durability caused by complex ions in seawater pose great challenges for its industrialization. In this review, a mechanistic analysis of durability issues of electrolytic seawater splitting is discussed. We critically analyze the development of seawater electrolysis and identify the durability challenges at both the anode and cathode. Particular emphasis is given to elucidating rational strategies for designing electrocatalysts/electrodes/interfaces with long lifetimes in realistic seawater including inducing passivating anion layers, preferential OH-adsorption, employing anti-corrosion materials, fabricating protective layers, immobilizing Cl- on the surface of electrocatalysts, tailoring Cl- adsorption sites, inhibition of OH- binding to Mg2+ and Ca2+, inhibition of Mg and Ca hydroxide precipitation adherence, and co-electrosynthesis of nano-sized Mg hydroxides. Synthesis methods of electrocatalysts/electrodes and innovations in electrolyzer are also discussed. Furthermore, the prospects for developing seawater splitting technologies for clean hydrogen generation are summarized. We found that researchers have rethought the role of Cl- ions, as well as more attention to cathodic reaction and electrolyzers, which is conducive to accelerate the commercialization of seawater electrolysis.

Nitrogen-Rich Molybdenum Nitride with Intrinsic CD39 Nucleotidase Activity

CD39 is one of the important nucleotidases to adjust extracellular adenosine triphosphate (ATP) and adenosine diphosphate (ADP) concentration. However, the enzyme mimics to simulate the activity of CD39 still remains to be explored. Herein nitrogen-rich molybdenum nitride (Mo5N6) nanosheets are explored to possess CD39-like activity, which are able to catalyze the hydrolysis of the high-energy phosphate bonds (HEPBs) in ATP and ADP but not the common phosphate bonds in adenosine monophosphate (AMP). The catalytic hydrolysis of the phosphate bond over Mo5N6-700 nanosheets is first investigated using para-nitrophenyl phosphate as the model substrate and then the CD39-like activity is further explored and verified by 31p NMR spectroscopy. Mo4+ on the surface of Mo5N6-700 nanosheets are the catalytic active sites. Using ATP as the model substrate, the Km and Vmax values of CD39-like activity at optimal pH 9.0 are 3.2 µmol L-1 and 18.5 µmol L-1 h-1, respectively. The CD39-like activity of Mo5N6-700 nanosheets enabled the down-regulation of intracellular ATP concentration to a larger degree for cancer cells than normal cells, which makes Mo5N6-700 nanosheets a potential therapeutic reagent for cancers.

In Situ Growth of MoN on Nickel Foam for Highly Efficient Hydrogen Evolution in Alkaline Solution

Highly efficient, stable, and low-cost hydrogen evolution catalysts are urgently required for water electrolysis. Herein, a method for in situ growth of medium-nitrogen nanosheet MoN catalysts with a large electrochemical surface area on nickel foam (NF) is proposed. The results show that the morphology of the as-prepared catalysts greatly depends on the nitrogen sources and nitridation temperature. The MoN/NF catalyst nitride at 700 °C using melamine as a nitrogen source exhibits a spindle-like morphology consisting of stacked nanosheets, which is conducive to exposing more active sites, thereby increasing the catalyst activity. The N atoms in MoN could adjust the chemical environment of the metal by changing the density of the d-band electron state, which further improves the HER performance. Benefiting from the regulation of Mo charge distribution and exposure to more active sites through N doping and morphological control, the MoN/NF catalyst exhibits superior HER performance with an overpotential of 70 mV at a current density of 10 mA·cm-2, a Tafel slope of 44.3 mV dec-1, and an Rct of 1.83 Ω, indicating high HER catalytic activity, fast kinetics, and excellent conductivity. Theoretical calculations reveal that among the (002), (202), and (200) planes of MoN, the (202) plane exhibits the lowest value of |ΔGH*| (0.47 eV), which is close to that of Pt(111) (0.14 eV). More importantly, MoN(202) also has the smallest work function of 3.58 eV, indicating an enhanced capability to offer electrons. This work develops a strategy to design high-performance and low-cost transition-metal nitride HER catalysts.

Nitrogen-doped carbon layer coated Co(OH)F/CoP2 nanosheets for high-current hydrogen evolution reaction in alkaline freshwater and seawater

Utilizing renewable energy such as offshore wind power to electrolyze seawater for hydrogen production offers a sustainable development pathway to address energy and climate change issues. In this study, by incorporating nitrogen-doped carbon quantum dots (N-CDs) into precursors, we successfully synthesized a nitrogen-doped carbon (NC)-layer-coated Co(OH)F/CoP2 catalyst NC@Co(OH)F/CoP2/NF loaded on nickel foam (NF). The introduction of N-CDs induced significant morphology change of the catalyst, facilitating the exposure of numerous active sites, ensuring the presence of catalytically active species CoP2 in nanoparticle form and avoiding agglomeration, which was advantageous to enhancing the overall hydrogen evolution reaction (HER) activity of the catalyst. The formation of Co-N bonds accelerated electron transfer, regulated the electronic structure, and optimized the catalyst's adsorption capacity for H* intermediates, which resulted in remarkably improved HER performance. In addition, Co(OH)F can also serve as a structural support, preventing the catalyst from collapsing during the HER catalytic process. NC@Co(OH)F/CoP2/NF exhibited excellent HER activity in alkaline freshwater and alkaline seawater, respectively requiring overpotentials of only 107 and 128 mV to achieve a current density of 100 mA cm-2. More importantly, it also demonstrated excellent HER activity at high current densities, with overpotentials of 189 and 237 mV at a current density of 1000 mA cm-2 in alkaline freshwater and alkaline seawater, respectively. This work provides new insights into the design and construction of highly efficient HER catalysts for applications in alkaline freshwater and seawater.

Recent advances of MXene@MOF composites for catalytic water splitting and wastewater treatment approaches

MXenes are a group of 2D material which have been derived from the layered transition metal nitrides and carbides and have the characteristics like electrical conductivity, high surface area and variable surface chemical composition. Self-assembly of clusters/metal ions and organic linkers forms metal organic framework (MOF). Their advantages of ultrahigh porosity, highly exposed active sites and many pore architectures have garnered them a lot of attention. But poor conductivity and instability plague several conventional MOF. To address the issue, MOF can be linked with MXenes that have rich surface functional groups and excellent electrical conductivity. In this review, different etching methods for exfoliation of MXene along with the synthesis methods of MXene/MOF composites are reviewed, including hydrothermal method, solvothermal method, in-situ growth method, and self-assembly method. Moreover, application of these MXene/MOF composites for catalytic water splitting and wastewater treatment were also discussed in details. In addition to increasing a single MOF conductivity and stability, MXenes can add a variety of new features, such the template effect. Due to these benefits, MXene/MOF composites can be effectively used in several applications, including photocatalytic/electrocatalytic water splitting, adsorption and degradation of pollutants from wastewater. Finally, the authors explored the current challenges and the future opportunities to improve the efficiency of MXene/MOF composites.

Enhanced Electrocatalytic Activity of Amorphized LaCoO3 for Oxygen Evolution Reaction

Amorphous inorganic perovskites have attracted significant attention as efficient electrocatalysts due to their unique structural flexibility and good catalytic activity. In particular, the disordered structure and a surface rich in defects such as oxygen vacancies can contribute to the superior electrocatalytic activity of amorphous oxides compared to their crystalline counterpart. In this work, we report the synthesis of LaCoO3, followed by an amorphization process through urea reduction with tailored modifications. The as-synthesized catalysts were thoroughly tested for their performance in oxygen evolution reaction (OER), Remarkably, the amorphous LaCoO3 synthesized at 450 °C (referred to as LCO-4) exhibits excellent OER catalytic activity. At an overpotential of 310 mV, it achieved a current density of 10 mA/cm-2, exceedingly fast to 1 A/cm-2 at an overpotential of only 460 mV. Moreover, LCO-4 exhibited several advantageous features compared to pristine LaCoO3 and LaCoO3 amorphized at other two temperatures (350 °C, LCO-3, and 550 °C, LCO-5). The amorphized LCO-4 catalyst showed a higher electrochemically active surface area, a key factor in boosting catalytic performance. Additionally, LCO-4 demonstrated the lowest Tafel slope of 70 mVdec-1, further highlighting its exceptional OER activity. Furthermore, the long-term stability of LCO-4 is notably superior than pristine LaCoO3 (LCO-P) and the other amorphized samples (LCO-3 and LCO-5). The enhanced catalytic activity of LCO-4 can be attributed to its unique disordered structure, small crystallite size, and higher concentration of oxygen vacancies in the final catalyst.

Multifunctional Design of Catalysts for Seawater Electrolysis for Hydrogen Production

Direct seawater electrolysis is a promising technology within the carbon-neutral energy framework, leveraging renewable resources such as solar, tidal, and wind energy to generate hydrogen and oxygen without competing with the demand for pure water. High-selectivity, high-efficiency, and corrosion-resistant multifunctional electrocatalysts are essential for practical applications, yet producing stable and efficient catalysts under harsh conditions remains a significant challenge. This review systematically summarizes recent advancements in advanced electrocatalysts for seawater splitting, focusing on their multifunctional designs for selectivity and chlorine corrosion resistance. We analyze the fundamental principles and mechanisms of seawater electrocatalytic reactions, discuss the challenges, and provide a detailed overview of the progress in nanostructures, alloys, multi-metallic systems, atomic dispersion, interface engineering, and functional modifications. Continuous research and innovation aim to develop efficient, eco-friendly seawater electrolysis systems, promoting hydrogen energy application, addressing efficiency and stability challenges, reducing costs, and achieving commercial viability.

Seawater electrolysis for fuels and chemicals production: fundamentals, achievements, and perspectives

Seawater electrolysis for the production of fuels and chemicals involved in onshore and offshore plants powered by renewable energies offers a promising avenue and unique advantages for energy and environmental sustainability. Nevertheless, seawater electrolysis presents long-term challenges and issues, such as complex composition, potential side reactions, deposition of and poisoning by microorganisms and metal ions, as well as corrosion, thus hindering the rapid development of seawater electrolysis technology. This review focuses on the production of value-added fuels (hydrogen and beyond) and fine chemicals through seawater electrolysis, as a promising step towards sustainable energy development and carbon neutrality. The principle of seawater electrolysis and related challenges are first introduced, and the redox reaction mechanisms of fuels and chemicals are summarized. Strategies for operating anodes and cathodes including the development and application of chloride- and impurity-resistant electrocatalysts/membranes are reviewed. We comprehensively summarize the production of fuels and chemicals (hydrogen, carbon monoxide, sulfur, ammonia, etc.) at the cathode and anode via seawater electrolysis, and propose other potential strategies for co-producing fine chemicals, even sophisticated and electronic chemicals. Seawater electrolysis can drive the oxidation and upgrading of industrial pollutants or natural organics into value-added chemicals or degrade them into harmless substances, which would be meaningful for environmental protection. Finally, the perspective and prospects are outlined to address the challenges and expand the application of seawater electrolysis.

Next-Generation Green Hydrogen: Progress and Perspective from Electricity, Catalyst to Electrolyte in Electrocatalytic Water Splitting

Green hydrogen from electrolysis of water has attracted widespread attention as a renewable power source. Among several hydrogen production methods, it has become the most promising technology. However, there is no large-scale renewable hydrogen production system currently that can compete with conventional fossil fuel hydrogen production. Renewable energy electrocatalytic water splitting is an ideal production technology with environmental cleanliness protection and good hydrogen purity, which meet the requirements of future development. This review summarizes and introduces the current status of hydrogen production by water splitting from three aspects: electricity, catalyst and electrolyte. In particular, the present situation and the latest progress of the key sources of power, catalytic materials and electrolyzers for electrocatalytic water splitting are introduced. Finally, the problems of hydrogen generation from electrolytic water splitting and directions of next-generation green hydrogen in the future are discussed and outlooked. It is expected that this review will have an important impact on the field of hydrogen production from water.

Interfacial Electronic Modulation of Mo5N6/Ni3S2 Heterojunction Array Boosts Electrocatalytic Alkaline Overall Water Splitting

Bifunctional electrocatalysts with excellent activity and durability are highly desirable for alkaline overall water splitting, yet remain a significant challenge. In this contribution, palm-like Mo5N6/Ni3S2 heterojunction arrays anchored in conductive Ni foam (denoted as Mo5N6-Ni3S2 HNPs/NF) are developed. Benefiting from the optimized electronic structure configuration, hierarchical branched structure and abundant heterogeneous interfaces, the as-synthesized Mo5N6-Ni3S2 HNPs/NF electrode exhibits remarkably stable bifunctional electrocatalytic activity in 1 m KOH solution. It only requires ultralow overpotentials of 59 and 190 mV to deliver a current density of 10 mA cm-2 for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in 1 m KOH solution, respectively. Importantly, the overall water splitting electrolyzer assembled by Mo5N6-Ni3S2 HNPs/NF exhibits an exceptionally low cell voltage (1.48 V@10 mA cm-2) and outstanding durability, surpassing most of the reported Ni-based bifunctional materials. Density functional theory (DFT) further confirms the heterostructure can optimize the Gibbs free energies of H and O-containing intermediates (OH, O, OOH) during HER and OER processes, thereby accelerating the catalytic kinetics of electrochemical water splitting. The findings provide a new design strategy toward low-cost and excellent catalysts for overall water splitting.

Mo5N6 nanosheets for fluorescent quenching and target recognition: Highly selectively sensing of sodium hexametaphosphate

Typical fluorescent biosensors use fluorescently labeled ssDNA for target recognition and nanomaterials for signal transduction. Herein, we propose a reverse sensing strategy that Mo5N6 nanosheets are used for target recognition while fluorescein (FAM)-labeled ssDNA only serves for signal generation. We discover that Mo5N6 nanosheets show high fluorescence quenching ability (>95%) and selective recognition for sodium hexametaphosphate (SHMP). After FAM-labeled ssDNA is adsorbed on Mo5N6 nanosheets, the fluorescence is quenched due to the photoinduced electron transfer (PET) effect between FAM and Mo5N6 nanosheets. SHMP can specifically displace the adsorbed FAM-labeled ssDNA from Mo5N6 nanosheets, resulting in more than 80% fluorescence recovery on addition of 5 μmol L-1 SHMP. This biosensor can sensitively detect SHMP down to 150 nmol L-1 and selectively recognize SHMP over glucose, lactose, common amino acids, Zn2+, Mg2+, Ca2+ and other phosphates (such as Na2HPO4, sodium pyrophosphate, sodium tripolyphosphate). This biosensor also shows great potential for the detection of SHMP in bacon sample. This work not only provides a facile sensitive and selective biosensor for SHMP but also exploits the application of transition metal nitrides in the field of sensing and biosensing.

Efficient bubble/precipitate traffic enables stable seawater reduction electrocatalysis at industrial-level current densities

Seawater electroreduction is attractive for future H2 production and intermittent energy storage, which has been hindered by aggressive Mg2+/Ca2+ precipitation at cathodes and consequent poor stability. Here we present a vital microscopic bubble/precipitate traffic system (MBPTS) by constructing honeycomb-type 3D cathodes for robust anti-precipitation seawater reduction (SR), which massively/uniformly release small-sized H2 bubbles to almost every corner of the cathode to repel Mg2+/Ca2+ precipitates without a break. Noticeably, the optimal cathode with built-in MBPTS not only enables state-of-the-art alkaline SR performance (1000-h stable operation at -1 A cm-2) but also is highly specialized in catalytically splitting natural seawater into H2 with the greatest anti-precipitation ability. Low precipitation amounts after prolonged tests under large current densities reflect genuine efficacy by our MBPTS. Additionally, a flow-type electrolyzer based on our optimal cathode stably functions at industrially-relevant 500 mA cm-2 for 150 h in natural seawater while unwaveringly sustaining near-100% H2 Faradic efficiency. Note that the estimated price (~1.8 US$/kgH2) is even cheaper than the US Department of Energy's goal price (2 US$/kgH2).

Direct Seawater Electrolysis: From Catalyst Design to Device Applications

Direct seawater electrolysis (DSE) for hydrogen production, using earth-abundant seawater as the feedstock and renewable electricity as the driving source, paves a new opportunity for flexible energy conversion/storage and smooths the volatility of renewable energy. Unfortunately, the complex environments of seawater impose significant challenges on the design of DSE catalysts, and the practical performance of many current DSE catalysts remains unsatisfactory on the device level. However, many studies predominantly concentrate on the development of electrocatalysts for DSE without giving due consideration to the specific devices. To mitigate this gap, the most recent progress (mainly published within the year 2020-2023) of DSE electrocatalysts and devices are systematically evaluated. By discussing key bottlenecks, corresponding mitigation strategies, and various device designs and applications, the tremendous challenges in addressing the trade-off among activity, stability, and selectivity for DSE electrocatalysts by a single shot are emphasized. In addition, the rational design of the DSE electrocatalysts needs to align with the specific device configuration, which is more effective than attempting to comprehensively enhance all catalytic parameters. This work, featuring the first review of this kind to consider rational catalyst design in the framework of DSE devices, will facilitate practical DSE development.

Synergistic Co-N/V-N dual sites in N-doped Co3V2O8 nanosheets: pioneering high-efficiency bifunctional electrolysis for high-current water splitting

Developing affluent dual-metal active sites bifunctional electrocatalysts for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) is essential to achieve large-scale water electrolysis, whereas still remains challenging. Herein, a novel nitrogen-doped cobalt-vanadium oxide with abundant Co-N and V-N dual active sites supported on nickel foam (N-Co3V2O8@NF) is constructed by a controllable impregnation-thermal nitridation strategy. The staggered nanosheet structure ensures optimal exposure of active sites. More importantly, N doping effectively regulates the electronic structure of the metal centers and induces the formation of Co-N and V-N dual active sites, which is conducive to improving the conductivity and hydrophilicity, thus synergistically enhancing the electrocatalytic efficiency. Consequently, the optimized N-Co3V2O8@NF exhibits prominent HER (63 mV@10 mA cm-2) and OER (256 mV@10 mA cm-2) activities, surpassing most contemporary bifunctional electrocatalysts. In practical application, the assembled N-Co3V2O8@NF(+/-) electrolyzer consistently achieved ultra-low cell voltages of 1.97 and 2.03 V at 500 and 1000 mA cm-2, respectively, superior to the benchmark RuO2@NF(+) || Pt/C@NF(-) and showcasing robust durability. This paves the way for its prospective adoption in industrial water electrolysis applications.

Atomically-Thin Holey 2D Nanosheets of Defect-Engineered MoN-Mo5 N6 Composites as Effective Hybridization Matrices

The defect engineering of inorganic solids has received significant attention because of its high efficacy in optimizing energy-related functionalities. Consequently, this approach is effectively leveraged in the present study to synthesize atomically-thin holey 2D nanosheets of a MoN-Mo5 N6 composite. This is achieved by controlled nitridation of assembled MoS2 monolayers, which induced sequential cation/anion migration and a gradual decrease in the Mo valency. Precise control of the interlayer distance of the MoS2 monolayers via assembly with various tetraalkylammonium ions is found to be crucial for synthesizing sub-nanometer-thick holey MoN-Mo5 N6 nanosheets with a tunable anion/cation vacancy content. The holey MoN-Mo5 N6 nanosheets are employed as efficient immobilization matrices for Pt single atoms to achieve high electrocatalytic mass activity, decent durability, and low overpotential for the hydrogen evolution reaction (HER). In situ/ex situ spectroscopy and density functional theory (DFT) calculations reveal that the presence of cation-deficient Mo5 N6 domain is crucial for enhancing the interfacial interactions between the conductive molybdenum nitride substrate and Pt single atoms, leading to enhanced electron injection efficiency and electrochemical stability. The beneficial effects of the Pt-immobilizing holey MoN-Mo5 N6 nanosheets are associated with enhanced electronic coupling, resulting in improvements in HER kinetics and interfacial charge transfer.

Enhanced d-π overlap in a graphene supported Ni/PtNi heterojunction for efficient seawater hydrogen evolution

d-π overlap, which represents overlap between metal-d and graphene-π orbitals to facilitate electron transfer, has rarely been reported. Ni/PtNi-G2 exhibits exceptional performance in seawater hydrogen evolution due to the electron-rich surface on Pt resulting from enhanced d-π overlap and subsequent electron transfer from graphene and Ni to Pt.

Metal Electrocatalysts for Hydrogen Production in Water Splitting

The rising demand for fossil fuels and the resulting pollution have raised environmental concerns about energy production. Undoubtedly, hydrogen is the best candidate for producing clean and sustainable energy now and in the future. Water splitting is a promising and efficient process for hydrogen production, where catalysts play a key role in the hydrogen evolution reaction (HER). HER electrocatalysis can be well performed by Pt with a low overpotential close to zero and a Tafel slope of about 30 mV dec-1. However, the main challenge in expanding the hydrogen production process is using efficient and inexpensive catalysts. Due to electrocatalytic activity and electrochemical stability, transition metal compounds are the best options for HER electrocatalysts. This study will focus on analyzing the current situation and recent advances in the design and development of nanostructured electrocatalysts for noble and non-noble metals in HER electrocatalysis. In general, strategies including doping, crystallization control, structural engineering, carbon nanomaterials, and increasing active sites by changing morphology are helpful to improve HER performance. Finally, the challenges and future perspectives in designing functional and stable electrocatalysts for HER in efficient hydrogen production from water-splitting electrolysis will be described.

Metal nitrides for seawater electrolysis

Electrocatalytic high-throughput seawater electrolysis for hydrogen production is a promising green energy technology that offers possibilities for environmental and energy sustainability. However, large-scale application is limited by the complex composition of seawater, high concentration of Cl- leading to competing reaction, and severe corrosion of electrode materials. In recent years, extensive research has been conducted to address these challenges. Metal nitrides (MNs) with excellent chemical stability and catalytic properties have emerged as ideal electrocatalyst candidates. This review presents the electrode reactions and basic parameters of the seawater splitting process, and summarizes the types and selection principles of conductive substrates with critical analysis of the design principles for seawater electrocatalysts. The focus is on discussing the properties, synthesis, and design strategies of MN-based electrocatalysts. Finally, we provide an outlook for the future development of MNs in the high-throughput seawater electrolysis field and highlight key issues that require further research and optimization.

Amorphous Co-Mo-P film on nickel foam: a superior bifunctional electrocatalyst for alkaline seawater splitting

Seawater splitting is a compelling avenue to produce abundant hydrogen, which requires high-performance and cost-effective catalysts. Constructing bimetallic transition metal phosphides is a feasible strategy to meet the challenge. Here, an amorphous Co-Mo-P film supported on nickel foam (Co-Mo-P/NF) electrode is developed with bifunctional properties for both the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in alkaline seawater. Corresponding results indicate that the introduction of Mo can improve the active sites and regulate the intrinsic activity. Such a Co-Mo-P/NF behaves with prominent electrocatalytic activity towards both HER and OER, demanding low overpotentials of 193 and 352 mV at 100 mA cm‒2in alkaline seawater, respectively. Furthermore, the assembled electrolyzer demands a pronounced overall seawater splitting activity with a low cell voltage of 1.76 V to deliver 100 mA cm-2presenting excellent durability without obvious attenuation after 24 h continuous stability test. This work expands the horizon to develop transition metal-phosphorus electrocatalysts with robust and efficient activity for overall seawater splitting.

Materials Design and System Innovation for Direct and Indirect Seawater Electrolysis

Green hydrogen production from renewably powered water electrolysis is considered as an ideal approach to decarbonizing the energy and industry sectors. Given the high-cost supply of ultra-high-purity water, as well as the mismatched distribution of water sources and renewable energies, combining seawater electrolysis with coastal solar/offshore wind power is attracting increasing interest for large-scale green hydrogen production. However, various impurities in seawater lead to corrosive and toxic halides, hydroxide precipitation, and physical blocking, which will significantly degrade catalysts, electrodes, and membranes, thus shortening the stable service life of electrolyzers. To accelerate the development of seawater electrolysis, it is crucial to widen the working potential gap between oxygen evolution and chlorine evolution reactions and develop flexible and highly efficient seawater purification technologies. In this review, we comprehensively discuss present challenges, research efforts, and design principles for direct/indirect seawater electrolysis from the aspects of materials engineering and system innovation. Further opportunities in developing efficient and stable catalysts, advanced membranes, and integrated electrolyzers are highlighted for green hydrogen production from both seawater and low-grade water sources.

Molecular Engineering of a Metal-Organic Polymer for Enhanced Electrochemical Nitrate-to-Ammonia Conversion and Zinc Nitrate Batteries

Metal-organic framework-based materials are promising single-site catalysts for electrocatalytic nitrate (NO3 - ) reduction to value-added ammonia (NH3 ) on account of well-defined structures and functional tunability but still lack a molecular-level understanding for designing the high-efficient catalysts. Here, we proposed a molecular engineering strategy to enhance electrochemical NO3 - -to-NH3 conversion by introducing the carbonyl groups into 1,2,4,5-tetraaminobenzene (BTA) based metal-organic polymer to precisely modulate the electronic state of metal centers. Due to the electron-withdrawing properties of the carbonyl group, metal centers can be converted to an electron-deficient state, fascinating the NO3 - adsorption and promoting continuous hydrogenation reactions to produce NH3 . Compared to CuBTA with a low NO3 - -to-NH3 conversion efficiency of 85.1 %, quinone group functionalization endows the resulting copper tetraminobenzoquinone (CuTABQ) distinguished performance with a much higher NH3 FE of 97.7 %. This molecular engineering strategy is also universal, as verified by the improved NO3 - -to-NH3 conversion performance on different metal centers, including Co and Ni. Furthermore, the assembled rechargeable Zn-NO3 - battery based on CuTABQ cathode can deliver a high power density of 12.3 mW cm-2 . This work provides advanced insights into the rational design of metal complex catalysts through the molecular-level regulation for NO3 - electroreduction to value-added NH3 .

Defect Enriched Tungsten Oxide Phosphate with Strategic Sulfur Doping for Effective Seawater Oxidation

The intrinsic ability of defects within the electrocatalysts can be judiciously utilized in designing robust electrocatalysts for efficient seawater oxidation. Herein, we have fabricated a novel tungsten oxide phosphate (W12PO38.5) with optimized sulfur doping triggering the insertion of a large number of defect sites. This allows for boosted OER performance in alkaline freshwater as well as seawater, avoiding the unwanted chlorine evolution reaction. The optimized electrocatalyst achieved high current densities of 500 mA cm-2 at an overpotential of just 387 mV in fresh water and 100 mA cm-2 at 380 mV in alkaline seawater for OER. Besides the excellent catalytic performances, the developed electrocatalyst appeared to be a durable catalyst as well. An interesting electrocatalytic activation caused by the generous electronic redistribution led the electrocatalyst to achieve great stability over 100 h at a 100 mA cm-2 current density in alkaline real seawater.

Nitrogen Plasma Activates CoMn-Layered Double Hydroxides for Superior Electrochemical Oxygen Evolution

Bimetallic layered double hydroxide is considered an ideal electrocatalytic material. However, due to the poor electrical conductivity of the bimetallic layered structure, obtaining highly active and stable catalysts through facile regulation strategies remains a great challenge. Herein, we use a simple corrosion strategy and nitrogen plasma technology to convert cobalt-based metal-organic frameworks into nitrogen-doped CoMn bimetallic layered double hydroxides (CoMn-LDH). Under the condition of regulating the local coordination environment of the catalytic active site and the presence of rich oxygen vacancy defects, N@CoMn-LDH/CC generates a low overpotential of 219 mV at 10 mA cm-2, which exceeds that of the commercial RuO2 catalyst. Density functional theory calculation shows that nitrogen doping improves the adsorption energy of the Mn site for oxygen evolution intermediates and reduces the reaction energy barrier of the Co site. Meanwhile, experiments and theoretical calculations verify that the mechanism of nitrogen doping regulating the oxygen evolution reaction (OER) follows the lattice oxygen oxidation mechanism, avoiding the collapse of the structure caused by catalyst reconstruction, thus improving the stability of oxygen evolution. This work provides a new simple strategy for the preparation of catalysts for a superior electrocatalytic oxygen evolution reaction.

Emerging materials and technologies for electrocatalytic seawater splitting

The limited availability of freshwater in renewable energy-rich areas has led to the exploration of seawater electrolysis for green hydrogen production. However, the complex composition of seawater presents substantial challenges such as electrode corrosion and electrolyzer failure, calling into question the technological and economic feasibility of direct seawater splitting. Despite many efforts, a comprehensive overview and analysis of seawater electrolysis, including electrochemical fundamentals, materials, and technologies of recent breakthroughs, is still lacking. In this review, we systematically examine recent advances in electrocatalytic seawater splitting and critically evaluate the obstacles to optimizing water supply, materials, and devices for stable hydrogen production from seawater. We demonstrate that robust materials and innovative technologies, especially selective catalysts and high-performance devices, are critical for efficient seawater electrolysis. We then outline and discuss future directions that could advance the techno-economic feasibility of this emerging field, providing a roadmap toward the design and commercialization of materials that can enable efficient, cost-effective, and sustainable seawater electrolysis.

Effective Hydrogen Production from Alkaline and Natural Seawater using WO3-x@CdS1-x Nanocomposite-Based Electrocatalysts

Offshore hydrogen production through water electrolysis presents significant technical and economic challenges. Achieving an efficient hydrogen evolution reaction (HER) in alkaline and natural seawater environments remains daunting due to the sluggish kinetics of water dissociation. To address this issue, we synthesized electrocatalytic WO3-x@CdS1-x nanocomposites (WCSNCs) using ultrasonic-assisted laser irradiation. The synthesized WCSNCs with varying CdS contents were thoroughly characterized to investigate their structural, morphological, and electrochemical properties. Among the samples tested, the WCSNCs with 20 wt % CdS1-x in WO3-x (Wx@Sx-20%) exhibited superior electrocatalytic performance for hydrogen evolution in a 1 M KOH solution. Specifically, the Wx@Sx-20% catalyst demonstrated an overpotential of 0.191 V at a current density of -10 mA/cm2 and a Tafel slope of 61.9 mV/dec. The Wx@Sx-20% catalysts demonstrated outstanding stability and durability, maintaining their performance after 24 h and up to 1000 CV cycles. Notably, when subjected to natural seawater electrolysis, the Wx@Sx-20% catalysts outperformed in terms of electrocatalytic HER activity and stability. The remarkable performance enhancement of the prepared electrocatalyst can be attributed to the combined effect of sulfur vacancies in CdS1-x and oxygen vacancies in WO3-x. These vacancies promote the electrochemically active surface area, enhance the rate of charge separation and transfer, increase the number of electrocatalytic active sites, and accelerate the HER process in alkaline and natural seawater environments.

Highly Efficient and Stable Hydrogen Evolution from Natural Seawater by Boron-Doped Three-Dimensional Ni2P-MoO2 Heterostructure Microrod Arrays

The rational design of highly active and stable electrocatalysts toward the hydrogen evolution reaction (HER) is highly desirable but challenging in seawater electrolysis. Herein we propose a strategy of boron-doped three-dimensional Ni2P-MoO2 heterostructure microrod arrays that exhibit excellent catalytic activity for hydrogen evolution in both alkaline freshwater and seawater electrolytes. The incorporation of boron into Ni2P-MoO2 heterostructure microrod arrays could modulate the electronic properties, thereby accelerating the HER. Consequently, the B-Ni2P-MoO2 heterostructure microrod array electrocatalyst exhibits a superior catalyst activity for HER with low overpotentials of 155, 155, and 157 mV at a current density of 500 mA cm-2 in 1 M KOH, 1 M KOH + NaCl, and 1 M KOH + seawater, respectively. It also exhibits exceptional performance for HER in natural seawater with a low overpotential of 248 mV at 10 mA cm-2 and a long-lasting lifetime of over 100 h.

CoFe nanoalloys encapsulated in nitrogen-doped carbon for efficient nitrite electroreduction to ammonia

Electrochemical nitrite (NO₂^-) reduction to ammonia (NH₃) can not only remove harmful NO₂^- in wastewater, but also produce valuable NH₃. Herein, a CoFe nanoalloy encapsulated in nitrogen-doped carbon (CoFe-NC) electrocatalyst was fabricated for nitrite reduction, which achieved a high NH₃ Faraday efficiency of 94.5%, and a large NH₃ yield of 4050.6 μg h^-1 cm^-2 in a neutral electrolyte.

Cu-Doped Heterointerfaced Ru/RuSe2 Nanosheets with Optimized H and H2 O Adsorption Boost Hydrogen Evolution Catalysis

Ruthenium chalcogenide is a highly promising catalytic system as a Pt alternative for hydrogen evolution reaction (HER). However, well-studied ruthenium selenide (RuSe₂ ) still exhibits sluggish HER kinetics in alkaline media due to the inappropriate adsorption strength of H and H₂ O. Herein, xx report a new design of Cu-doped Ru/RuSe₂ heterogeneous nanosheets (NSs) with optimized H and H₂ O adsorption strength for highly efficient HER catalysis in alkaline media. Theoretical calculations reveal that the superior HER performance is attributed to a synergistic effect of the unique heterointerfaced structure and Cu doping, which not only optimizes the electronic structure with a suitable d-band center to suppress proton overbinding but also alleviates the energy barrier with enhanced H₂ O adsorption. As a result, Cu-doped heterogeneous Ru/RuSe₂ NSs exhibit a small overpotential of 23 mV at 10 mA cm^-2 , a low Tafel slope of 58.5 mV dec^-1 and a high turnover frequency (TOF) value of 0.88 s^-1 at 100 mV for HER in alkaline media, which is among the best catalysts in noble metal-based electrocatalysts toward HER. The present Cu-doped Ru/RuSe₂ NSs interface catalyst is very stable for HER by showing no activity decay after 5000-cycle potential sweeps. This work heralds that heterogeneous interface modulation opens up a new strategy for the designing of more efficient electrocatalysts.

In situ synthesis of two-dimensional graphene-like nickel-molybdenum nitride as efficient electrocatalyst towards water-splitting under large-current density

Transition metal nitride (TMNs) electrocatalysts have attracted tremendous attentions for their unique electron structure, high activity, and excellent stability. Herein, a two-dimensional (2D) graphene-like structured nickel-molybdenum nitride (Ni-MoN) on nickel foam (NF), is prepared via facile hydrothermal and following nitridation process. The as-prepared Ni-MoN-450 (pyrolysis at 450 °C) displays good hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) performances in alkaline media. Only 22 mV and 117 mV are needed to achieve current densities of 10 mA cm^-2 and 500 mA cm^-2 in 1.0 M KOH, respectively, toward HER. The assembled two-electrode system, with the synthesized Ni-MoN-450 as the anode and cathode, exhibits good performance to achieve 1000 mA cm^-2 in 1.0 M KOH + 25 °C and 6.0 M KOH + 80 °C. Moreover, it also presents long-term stability under large-current density, which verified its robust property.

Phase Evolution on the Hydrogen Adsorption Kinetics of NiFe-Based Heterogeneous Catalysts for Efficient Water Electrolysis

Transition metal layered double hydroxides, especially nickel-iron layered double hydroxide (NiFe-LDH) shows significant advancement as efficient oxygen evolution reaction (OER) electrocatalyst but also plays a momentous role as a precursor for NiFe-based hydrogen evolution reaction (HER) catalysts. Herein, a simple strategy for developing Ni-Fe-derivative electrocatalysts via phase evolution of NiFe-LDH under controllable annealing temperatures in an argon atmosphere is reported. The optimized catalyst annealed at 340 ^o C (denoted NiO/FeNi₃ ) exhibits superior HER properties with an ultralow overpotential of 16 mV@10 mA cm^-2 . Density functional theory simulation and in situ Raman analyses reveal that the excellent HER properties of the NiO/FeNi₃ can be attributed to the strong electronic interaction at the interface of the metallic FeNi₃ and semiconducting NiO, which optimizes the H₂ O and H adsorption energies for efficient HER and OER catalytic processes. This work will provide rational insights into the subsequent development of related HER electrocatalysts and other corresponding compounds via LDH-based precursors.

Tunable Heterogeneous FeCo Alloy-Mo0.82N Bifunctional Electrocatalysts for Temperature-Adapted Zn-Air Batteries

The practical applications of temperature-tolerant Zn-air batteries (ZABs) rely on highly active and stable bifunctional catalysts that accelerate cathodic oxygen reduction (ORR) and oxygen evolution (OER) reactions. Herein, we successfully integrated fascinating transition metal nitrides and FeCo alloys through a simple coordination assembly and pyrolysis process. Importantly, the alloy-to-nitride ratio in the heterogeneous catalyst can be carefully regulated through the subsequent etching process. Moreover, the composition-dependent ORR/OER performance of the FeCo-Mo_0.82N catalysts was revealed. Aqueous ZABs using the optimized FeCo-Mo_0.82N-60 as a cathode exhibit a high peak power density of 149.7 mW cm^-2 and an impressive stability of 600 h with a low charge-discharge voltage gap decay rate of 0.025 mV h^-1, which exceeds those of most of recent reports. Furthermore, the FeCo-Mo_0.82N-60-based flexible ZABs display a small specific capacity degradation (3%) from 40 to -10 °C, demonstrating excellent temperature tolerance.

Engineering cation vacancies in high-entropy layered double hydroxides for boosting the oxygen evolution reaction

High-entropy layered double hydroxides (HE-LDHs) are emerging as promising electrocatalysts towards the OER due to their high-entropy effect and the cocktail effect. However, the catalytic activity and stability of HE-LDHs is, as yet, unsatisfactory. Herein, we designed FeCoNiCuZn LDHs with rich cation vacancies, which need only low overpotentials of 227, 275 and 293 mV to reach 10, 100 and 200 mA cm^-2, respectively, and show almost no decay up to 200 h at 200 mA cm^-2. DFT calculations validate that the cation vacancies can boost the intrinsic activity of HE-LDHs through optimizing the adsorption energy of OER intermediates.

Iron-Doped Monoclinic Strontium Iridate as a Highly Efficient Oxygen Evolution Electrocatalyst in Acidic Media

Ir-based perovskite oxides are efficient electrocatalysts for anodic oxygen evolution. This work presents a systematic study of the doping effects of Fe on the OER activity of monoclinic SrIrO₃ to reduce the consumption of Ir. The monoclinic structure of SrIrO₃ was retained when the Fe/Ir ratio was less than 0.1/0.9. Upon further increases in the Fe/Ir ratio, the structure of SrIrO₃ changed from a 6H to 3C phase. The SrFe_0.1Ir_0.9O₃ had the highest activity among the investigated catalysts with the lowest overpotential of 238 mV at 10 mA cm^-2 in 0.1 M HClO₄ solution, which could be attributed to the oxygen vacancies induced by the Fe dopant and the IrOx formed upon the dissolution of Sr and Fe. The formation of oxygen vacancies and uncoordinated sites at the molecular level may be responsible for the improved performance. This work explored the effect of Fe dopants in boosting the OER activity of SrIrO₃, thus providing a detailed reference to tune perovskite-based electrocatalyst by Fe for other applications.

Enhancing Resistance to Chloride Corrosion by Controlling the Morphologies of PtNi Electrocatalysts for Alkaline Seawater Hydrogen Evolution

A solvothermal method to prepare PtNi alloys that have differing morphologies is described. By adjusting the feed ratio of Pt and Ni precursors in this process, PtNi alloys with different compositions (Pt : Ni atomic ratio from 1 : 3 to 3 : 1) and morphologies (evolution from nanobranches to nanoparticles) are generated. The prepared Pt₄₈ Ni₅₂ alloy, which has a composite morphology comprised of nanobranches and nanoparticles, exhibits superior activity and durability towards the hydrogen evolution reaction (HER) in seawater compared to those of commercial Pt/C catalyst and other PtNi alloys that have different compositions and morphologies. The excellent seawater HER performance of Pt₄₈ Ni₅₂ is ascribed to its nanobranch/nanoparticle morphology that optimally facilitates electron accumulation on Pt, which enhances resistance to chloride corrosion in seawater.

Fabrication of a Biomass-Derived Activated Carbon-Based Anode for High-Performance Li-Ion Batteries

Porous carbons are highly attractive and demanding materials which could be prepared using biomass waste; thus, they are promising for enhanced electrochemical capacitive performance in capacitors and cycling efficiency in Li-ion batteries. Herein, biomass (rice husk)-derived activated carbon was synthesized via a facile chemical route and used as anode materials for Li-ion batteries. Various characterization techniques were used to study the structural and morphological properties of the prepared activated carbon. The prepared activated carbon possessed a carbon structure with a certain degree of amorphousness. The morphology of the activated carbon was of spherical shape with a particle size of ~40-90 nm. Raman studies revealed the characteristic peaks of carbon present in the prepared activated carbon. The electrochemical studies evaluated for the fabricated coin cell with the activated carbon anode showed that the cell delivered a discharge capacity of ~321 mAhg^-1 at a current density of 100 mAg^-1 for the first cycle, and maintained a capacity of ~253 mAhg^-1 for 400 cycles. The capacity retention was found to be higher (~81%) with 92.3% coulombic efficiency even after 400 cycles, which showed excellent cyclic reversibility and stability compared to commercial activated carbon. These results allow the waste biomass-derived anode to overcome the problem of cyclic stability and capacity performance. This study provides an insight for the fabrication of anodes from the rice husk which can be redirected into creating valuable renewable energy storage devices in the future, and the product could be a socially and ethically acceptable product.

Prediction of Three-Metal Cluster Catalysts on Two-Dimensional W2N3 Support with Integrated Descriptors for Electrocatalytic Nitrogen Reduction

In the electrocatalytic nitrogen reduction reaction (NRR), nitrogen (N2) is chemically inert, it is difficult to break the triple bond, and the subsequent protonation step is very challenging. Suitable catalysts with high selectivity and high activity are needed to promote the electrocatalytic NRR. We screen a large number of clusters composed of three metal atoms embedded into a two-dimensional metal nitride, W2N3, with a N vacancy, and calculate the reaction energetics. The VNiCu cluster has the best catalytic activity among all the catalysts proposed so far. The Fe3 and Fe2Co clusters are excellent catalysts as well. In all cases, spin polarization is needed to observe the catalytic effect. We establish the optimal NRR path and confirm that it remains unchanged in the presence of a solvent. We find three groups of descriptors that can well predict the materials' properties and exhibit linear relationships with the NRR limiting potential.

Engineering Multilevel Collaborative Catalytic Interfaces with Multifunctional Iron Sites Enabling High-Performance Real Seawater Splitting

Given the abundant reserves of seawater and the scarcity of freshwater, real seawater electrolysis is a more economically appealing technology for hydrogen production relative to orthodox freshwater electrolysis. However, this technology is greatly precluded by the undesirable chlorine oxidation reaction and severe chloride corrosion at the anode, further restricting the catalytic efficiency of overall seawater splitting. Herein, a feasible strategy by engineering multifunctional collaborative catalytic interfaces is reported to develop porous metal nitride/phosphide heterostructure arrays anchoring on conductive Ni2P surfaces with affluent iron sites. Collaborative catalytic interfaces among iron phosphide, bimetallic nitride, and porous Ni2P supports play a positive role in improving water adsorption/dissociation and hydrogen adsorption behaviors of active Fe sites evidenced by theoretical calculations for hydrogen evolution reactions, and enhancing oxygenated species adsorption and nitrate-rich passivating layers resistant to chloride corrosion for oxygen evolution reaction, thus cooperatively propelling high-performance bifunctional seawater splitting. The resultant material Fe2P/Ni1.5Co1.5N/Ni2P performs excellently as a self-standing bifunctional catalyst for alkaline seawater splitting. It requires extremely low cell voltages of 1.624 and 1.742 V to afford current densities of 100 and 500 mA/cm2 in 1 M KOH seawater electrolytes, respectively, along with superior long-term stability, outperforming nearly all the ever-reported non-noble bifunctional electrocatalysts and benchmark Pt/IrO2 coupled electrodes for freshwater/seawater electrolysis. This work presents an effective strategy for greatly enhancing the catalytic efficiency of non-noble catalysts toward green hydrogen production from seawater electrolysis.

Nano-Dimensional Carbon Nanosphere Supported Non-Precious Metal Oxide Composite: A Cathode Material for Sea Water Reduction

Generation of hydrogen fuel at cathode during the electrolysis of seawater can be economically beneficial considering the vast availability of the electrolyte although it faces sluggishness caused by the anode reactions. In this regard a carbon nanosphere-protected CuO/Co₃O₄ (CCuU) composite was synthesized through heat treatment and was used as the cathode material for electrocatalytic seawater splitting. CCuU showed a significantly low overpotential of 73 mV@10 mA cm^-2, Tafel slope of 58 mV dec^-1 and relatively constant activity and morphology over a long time electrocatalytic study. A synergy within metal oxide centers was observed that boosted the proton-electron transfer at the active site. Moreover, the presence of carbon support increased the electroactive surface area and stability of the composite. The activity of the CCuU was studied for HER in KOH and alkaline NaCl solution to understand the activity. This work will pave the way for designing mesoporous non-precious electrocatalysts towards seawater electrocatalysis.

Atomically Interfacial Engineering on Molybdenum Nitride Quantum Dots Decorated N-doped Graphene for High-Rate and Stable Alkaline Hydrogen Production

The development of low-cost, high-efficiency, and stable electrocatalysts for hydrogen evolution reaction (HER) under alkaline conditions is a key challenge in water electrolysis. Here, an interfacial engineering strategy that is capable of simultaneously regulating nanoscale structure, electronic structure, and interfacial structure of Mo₂ N quantum dots decorated on conductive N-doped graphene via codoping single-atom Al and O (denoted as AlO@Mo₂ N-NrGO) is reported. The conversion of Anderson polyoxometalates anion cluster ([AlMo₆ O₂₄ H₆ ]^3- , denoted as AlMo6) to Mo₂ N quantum dots not only result in the generation of more exposed active sites but also in situ codoping atomically dispersed Al and O, that can fine-tune the electronic structure of Mo₂ N. It is also identified that the surface reconstruction of AlOH hydrates in AlO@Mo₂ N quantum dots plays an essential role in enhancing hydrophilicity and lowering the energy barriers for water dissociation and hydrogen desorption, resulting in a remarkable alkaline HER performance, even better than the commercial 20% Pt/C. Moreover, the strong interfacial interaction (MoN bonds) between AlO@Mo₂ N and N-doped graphene can significantly improve electron transfer efficiency and interfacial stability. As a result, outstanding stability over 300 h at a current density higher than 100 mA cm^-2 is achieved, demonstrating great potential for the practical application of this catalyst.

Amorphous Co-Mo-B Film: A High-Active Electrocatalyst for Hydrogen Generation in Alkaline Seawater

The development of efficient electrochemical seawater splitting catalysts for large-scale hydrogen production is of great importance. In this work, we report an amorphous Co-Mo-B film on Ni foam (Co-Mo-B/NF) via a facile one-step electrodeposition process. Such amorphous Co-Mo-B/NF possesses superior activity with a small overpotential of 199 mV at 100 mA cm-2 for a hydrogen evolution reaction in alkaline seawater. Notably, Co-Mo-B/NF also maintains excellent stability for at least 24 h under alkaline seawater electrolysis.

Cobalt Molybdenum Nitride-Based Nanosheets for Seawater Splitting

The development of cost-effective bifunctional catalysts for water electrolysis is both a crucial necessity and an exciting scientific challenge. Herein, a simple approach based on a metal-organic framework sacrificial template to preparing cobalt molybdenum nitride supported on nitrogen-doped carbon nanosheets is reported. The porous structure of produced composite enables fast reaction kinetics, enhanced stability, and high corrosion resistance in critical seawater conditions. The cobalt molybdenum nitride-based electrocatalyst is tested toward both oxygen evolution reaction and hydrogen evolution reaction half-reactions using the seawater electrolyte, providing excellent performances that are rationalized using density functional theory. Subsequently, the nitride composite is tested as a bifunctional catalyst for the overall splitting of KOH-treated seawater from the Mediterranean Sea. The assembled system requires overpotentials of just 1.70 V to achieve a current density of 100 mA cm^-2 in 1 M KOH seawater and continuously works for over 62 h. This work demonstrates the potential of transition-metal nitrides for seawater splitting and represents a step forward toward the cost-effective implementation of this technology.