Architecture-dependent surface chemistry for Pt monolayers on carbon-supported Au

The enhancement in the performance of ultra-small core-shell Au@AuPt nanoparticles toward HER and ORR by surface engineering

In this work, ultra-small core-shell (USCS) Au_38.4@Au_4.1Pt_57.5 nanoparticles (NPs) with an optimal Pt-to-Au ratio were successfully prepared by the optimal etching treatment of USCS Au@AuPt NPs by Fe(III) ions to remove some exposed Au atoms on their outermost surfaces. The as-prepared USCS Au_38.4@Au_4.1Pt_57.5 NPs with Fe(III)-etching treatment for 2 h loaded on carbon black as catalysts (USCS^2h Au_38.4@Au_4.1Pt_57.5-NP/C catalysts) exhibit superior electrocatalytic activity and durability for both the hydrogen evolution reaction (HER) and oxygen reduction reaction (ORR) in acidic media. For instance, the overpotential of USCS^2h Au_38.4@Au_4.1Pt_57.5-NP/C catalysts toward the HER is 13 mV at a current density of -10 mA cm^-2 (η₁₀ = 13 mV), which is much better than that of commercial Pt/C catalysts (η₁₀ = 31 mV). Moreover, their mass activity (63.8 A mg_Pt^-1) is about 16.4 times larger than that of commercial Pt/C catalysts (3.9 A mg_Pt^-1). In addition, they also present better long-term stability. Furthermore, they also show an improved activity toward the ORR in terms of the half-wave potential (E_1/2) (0.89 V vs. RHE), which is more positive by about 38 mV than commercial Pt/C catalysts (0.852 V). In addition, they also show a higher kinetic current density (14.22 mA cm^-2 at 0.85 V) and better long-term durability. This etching-treatment strategy can be extended to further improve the catalytic performance of ultra-small Au-based bimetallic or multi-metallic NPs by surface engineering.

An alternative, low-dissolution counter electrode to prevent deceptive enhancement of HER overpotential

Electrochemical hydrogen evolution reaction (HER) is typically studied in three-electrode system. In this system, several counter electrodes are commonly used to ensure fast kinetics, including Pt, gold, and glassy carbon. However, the extensive application of such electrodes has raised caveats on the contribution of the redox-active species dissolving from such electrodes and redepositing on the surface of the working electrode to the measured overpotential. Consequently, this has been frequently confused with the actual electrochemical signature of the working electrode catalyst, resulting in a deceptive enhancement in the recorded overpotential. This issue becomes more critical when the electrolysis measurements involve an activation step, necessitating the need for alternative counter electrodes that are stable, especially in acidic medium, which is commonly used as the electrolyte in HER studies. Herein, while we systematically unveil such problems, an alternative counter electrode that overcomes those problems is demonstrated. Specifically, the correlation between the working electrode area to that of the counter electrode, the dissolution rate of the counter electrode, and the potential range used in the activation/cleaning of the surface on accelerating the dissolution rate is explored and discussed in detail. Finally, commercial Ti mesh is demonstrated as an alternative emerging counter electrode, which is proven to be very stable and convenient to study the HER in acidic media.

Carbon-Supported Noble-Metal Nanoparticles for Catalytic Applications—A Review

Noble-metal nanoparticles (NMNPs), with their outstanding properties, have been arousing the interest of scientists for centuries. Although our knowledge of them is much more significant today, and we can obtain NMNPs in various sizes, shapes, and compositions, our interest in them has not waned. When talking about noble metals, gold, silver, and platinum come to mind first. Still, we cannot forget about elements belonging to the so-called platinum group, such as ruthenium, rhodium, palladium, osmium, and iridium, whose physical and chemical properties are very similar to those of platinum. It makes them highly demanded and widely used in various applications. This review presents current knowledge on the preparation of all noble metals in the form of nanoparticles and their assembling with carbon supports. We focused on the catalytic applications of these materials in the fuel-cell field. Furthermore, the influence of supporting materials on the electrocatalytic activity, stability, and selectivity of noble-metal-based catalysts is discussed.

Sandwiched Graphene Interdiffusion Barrier for Preserving Au@Pt Atomically Thin Core@Shell Structure and the Resulting Oxygen Reduction Reaction Catalytic Activity

The concept of a core-shell metallic structures, with a few atomic layers of the "shell" metal delineated from the "core" metal with atomic sharpness opens the door to a multitude of surface-driven materials properties that can be tuned. However, in practice, such architectures are difficult to retain due to the entropic cost of a segregated near-surface architecture, and the core and surface atoms inevitably mix through interdiffusion over time. We present here a systematic study of interdiffusion in a Pt on Au core-shell architecture and the role of an interrupting single layer of graphene sandwiched between them. The physical and chemical structure of the (near)surface is probed via mean-free-path tuned X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy (HRTEM), and electrochemistry (the oxygen reduction reaction, ORR). We find that at operating temperatures above 100 °C, there is potential for interdiffusion to occur between the primary and support metals of the core-shell catalyst system, which can diminish the catalyst activity toward ORR. The introduction of a single-layer graphene, as an interface between the core and shell metal layers, acts as a barrier that prevents unwanted surface alloying between the layered metals. HRTEM imaging shows that fully wetted Pt monolayers can be grown on a graphene template, allowing a high level of surface utilization of the catalyst material. We present how the use of graphene as a barrier to diffusion mitigates the loss of surface catalytic sites, showing much improved retention of Pt monolayer surface at elevated temperatures.

Atomic Layer Deposition of Pd Nanoparticles on TiO₂ Nanotubes for Ethanol Electrooxidation: Synthesis and Electrochemical Properties

Palladium nanoparticles are grown on TiO2 nanotubes by atomic layer deposition (ALD), and the resulting three-dimensional nanostructured catalysts are studied for ethanol electrooxidation in alkaline media. The morphology, the crystal structure, and the chemical composition of the Pd particles are fully characterized using scanning and transmission electron microscopies, X-ray diffraction, and X-ray photoelectron spectroscopy. The characterization revealed that the deposition proceeds onto the entire surface of the TiO2 nanotubes leading to the formation of well-defined and highly dispersed Pd nanoparticles. The electrooxidation of ethanol on Pd clusters deposited on TiO2 nanotubes shows not only a direct correlation between the catalytic activity and the particle size but also a steep increase of the response due to the enhancement of the metal-support interaction when the crystal structure of the TiO2 nanotubes is modified by annealing at 450 °C in air.

Layer-by-layer evolution of structure, strain, and activity for the oxygen evolution reaction in graphene-templated Pt monolayers

In this study, we explore the dimensional aspect of structure-driven surface properties of metal monolayers grown on a graphene/Au template. Here, surface limited redox replacement (SLRR) is used to provide precise layer-by-layer growth of Pt monolayers on graphene. We find that after a few iterations of SLRR, fully wetted 4-5 monolayer Pt films can be grown on graphene. Incorporating graphene at the Pt-Au interface modifies the growth mechanism, charge transfers, equilibrium interatomic distances, and associated strain of the synthesized Pt monolayers. We find that a single layer of sandwiched graphene is able to induce a 3.5% compressive strain on the Pt adlayer grown on it, and as a result, catalytic activity is increased due to a greater areal density of the Pt layers beyond face-centered-cubic close packing. At the same time, the sandwiched graphene does not obstruct vicinity effects of near-surface electron exchange between the substrate Au and adlayers Pt. X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS) techniques are used to examine charge mediation across the Pt-graphene-Au junction and the local atomic arrangement as a function of the Pt adlayer dimension. Cyclic voltammetry (CV) and the oxygen reduction reaction (ORR) are used as probes to examine the electrochemically active area of Pt monolayers and catalyst activity, respectively. Results show that the inserted graphene monolayer results in increased activity for the Pt due to a graphene-induced compressive strain, as well as a higher resistance against loss of the catalytically active Pt surface.

Oxygen reduction electrocatalyst of Pt on Au nanoparticles through spontaneous deposition

A straightforward one-step spontaneous deposition approach for growth of Pt atomic shell on Au nanoparticles and the superior activity and durability of the resulted Pt-on-Au nanoparticles for the oxygen reduction reaction (ORR) are reported. Transmission electron microscopy, X-ray photoelectron spectroscopy, energy-dispersive spectrometry, and electrochemical measurements indicate that Pt can be spontaneously deposited on Au surface upon simply dispersing carbon-supported Au nanoparticles in PtCl42–-containing solution, without introducing any extraneous reducing agents or any pre/post-treatments. The deposited Pt atoms are uniformly distributed on the surface of Au nanoparticles, with coverage tunable by the concentration of PtCl42– and temperatures. An approximate monolayer of Pt forms at temperature of ca. 80 °C and PtCl42– concentrations of above 10–4 mol/L. The obtained Pt-on-Au core–shell nanoparticles catalyze the ORR with specific and mass activities of Pt that are 3.5 times higher than that of pure Pt nanoparticles. Moreover, they exhibit no visible activity degradation after undergoing long-term oxidization/reduction cycling in O2-saturated acid media, therefore showing great prospect as durable cathode electrocatalysts in proton-exchange membrane fuel cells.

Architecturally designed Pt–MoS2 and Pt–graphene composites for electrocatalytic methanol oxidation

Pt particles (2–3 nm) deposited using a liquid–liquid interface reaction technique are used to construct LbL architectures to form MoS₂/graphene composites for efficient methanol oxidation.

Ir-Surface enriched porous Ir-Co oxide hierarchical architecture for high performance water oxidation in acidic media

The large-scale application of acidic water electrolysis as a viable energy storage technology has been hindered by the high demand of precious metal oxides at anode to catalyze the oxygen evolution reaction (OER). We report an Ir-Co binary oxide electrocatalyst for OER fabricated by a multistep process of selective leaching of Co from Co-rich composite oxides prepared through thermal decomposition. The stepwise leaching of the Co component from the composites leads to the formation of macro- and mesoscale voids walled by a cross-linked nanoporous network of rod- and wedge-like building units of Ir-Co binary oxide with a rutile phase structure and an Ir-enriched surface. In comparison, Ir-Co binary oxide with similar composition prepared by direct thermal decomposition method exhibits a loose nanoparticle aggregation morphology with a Co-enriched surface. The cross-linked porous Ir-Co binary oxide from selective leaching is about 3-fold more active for the OER than that from direct thermal decomposition. Compared with pure IrO2 from thermal decomposition, the Co-leached binary oxide is ca. two times more active and is much more durable during continuous oxygen evolution under a constant potential of 1.6 V, thus showing a possibility of reducing the demand of the expensive and scarce Ir in OER electrocatalyst for acidic water splitting.