Adsorption behavior of EDTA-graphene oxide for Pb (II) removal

Metallic 1T/1T' phase TMD nanosheets with enhanced chemisorption sites for ultrahigh-efficiency lead removal

Two-dimensional (2D) materials, as adsorbents, have garnered great attention in removing heavy metal ions (HMIs) from drinking water due to their extensive exposed adsorption sites. Nevertheless, there remains a paucity of experimental research to remarkably unlock their adsorption capabilities and fully elucidate their adsorption mechanisms. In this work, exceptional lead ion (Pb2+) (a common HMI) removal capacity (up to 758 mg g-1) is achieved using our synthesized metallic 1T/1T' phase 2D transition metal dichalcogenide (TMD, including MoS2, WS2, TaS2, and TiS2) nanosheets, which hold tremendous activated S chemisorption sites. The residual Pb2+ concentration can be reduced from 2 mg L-1 to 2 μg L-1 within 0.5 min, meeting the drinking water standards following World Health Organization guideline (Pb2+ concentrations <10 μg L-1). Atomic-scale characterizations and calculations based on density functional theory unveil that Pb2+ bond to the top positions of transition metal atoms in a single-atom form through the formation of S-Pb bonds. Point-of-use (POU) devices fabricated by our reported metallic phase MoS2 nanosheets exhibit treatment capacity of 55 L-water g-1-adsorbent for feed Pb2+ concentration of 1 mg L-1, which is 1-3 orders of magnitude higher than other 2D materials and commercial activated carbon.

Remediation of water containing lead(II) using (3-iminodiacetic acid) propyltriethoxysilane graphene oxide

A novel chelating adsorbent based on (3-iminodiacetic acid) propyltriethoxysilane graphene oxide (IAT-GO) has been developed, showing exceptional promise for capturing lead. IAT-GO is made by combining a high-surface-area graphene oxide with a specially designed chelating ligand, which can selectively and efficiently remove lead. The synthesis of IAT-GO involves a two-step progression. In the first step, covalent bonds form between graphene oxide and (3-aminopropyl)-triethoxysilane (AT) through hydrolysis, condensation, and epoxide ring opening reactions. In the second step, nucleophilic substitution reactions occur between the primary amines and chloroacetic acid (CAA). A comprehensive suite of characterization techniques, including XPS, UV-Vis, XRD, Raman, FTIR, TEM, and SEM, provides detailed insights into the IAT-GO adsorbent's chemical composition and physical form, elucidating its intricate structure and morphology. Optimizing the experimental conditions for using the adsorbent material to remove Pb(II) ions from contaminated water revealed a maximum adsorption capacity of 124.0 mg/g at pH 5 and 30 min. The IAT-GO displays high selectivity for Pb(II) in a mixture of six metal ions containing 100 ppm of each one. Moreover, the IAT-GO shows 100% removal of Pb(II) for concentrations lower than 50 ppm. The excellent fit of the experimental data with the Langmuir adsorption isotherm and pseudo-second-order kinetic models (R2 > 99%) indicates that Pb(II) ion uptake onto the IAT-GO surface occurs via the monolayer formation of mercury ions. IAT-GO demonstrates exceptional potential as an innovative adsorbent for lead-contaminated water. Nitric acid (0.4 M) effectively regenerates the material, while its reusability remains impressive even after five cycles (> 97% removal efficiency). Therefore, this study highlights the development of a groundbreaking material, IAT-GO, with exceptional potential for remediating lead-contaminated water. Its high efficiency, selectivity, reusability, and cost-effectiveness make it a promising candidate for real-world applications.

A study on a fixed-bed for Pb(ii) removal by modified alkaline lignin-sodium alginate composite hydrogel

In this work, alkaline lignin (AL) co-modified with trimercapto-s-triazine trisodium salt (TMT) and sodium alginate (SA) as a matrix were used to create a composite hydrogel for removing heavy metals, specifically divalent lead (Pb) from water. The obtained hydrogel beads were packed into a fixed bed, and then various operating conditions were explored to assess their impact on the efficiency of Pb(ii) removal. The findings indicated that the optimal removal efficiency for Pb(ii) was attained using an inflow rate of 0.159 L min-1, a hydrogel-II filling height of 40 cm, an initial Pb(ii) concentration of 10 mg L-1, and a bottom inflow direction. In the third adsorption-desorption cycle experiment, the breakthrough curve reached equilibrium after 650 min, in which equilibrium time for the initial breakthrough curve was 855 min, indicating that hydrogel-II exhibit good regeneration capability. This work serves as a foundation for practical applications in removing heavy metals from wastewater.

Intestinal toxicity of Pb: Structural and functional damages, effects on distal organs and preventive strategies

Lead (Pb) is one of the most common heavy metal pollutants that possesses multi-organ toxicity. For decades, great efforts have been devoted to investigate the damage of Pb to kidney, liver, bone, blood cells and the central nervous system (CNS). For the common, dietary exposure is the main avenue of Pb, but our knowledge of Pb toxicity in gastrointestinal tract (GIT) remains quite insufficient. Importantly, emerging evidence has documented that gastrointestinal disorders affect other distal organs like brain and liver though gut-brain axis or gut-liver axis, respectively. This review focuses on the recent understanding of intestinal toxicity of Pb exposure, including structural and functional damages. We also review the influence and mechanism of intestinal toxicity on other distal organs, mainly concentrated on brain and liver. At last, we summarize the bioactive substances that reported to alleviate Pb toxicity, providing potential dietary intervention strategies to prevent or attenuate Pb toxicity.

Recent Progress on the Adsorption of Heavy Metal Ions Pb(II) and Cu(II) from Wastewater

With the processes of industrialization and urbanization, heavy metal ion pollution has become a thorny problem in water systems. Among the various technologies developed for the removal of heavy metal ions, the adsorption method is widely studied by researchers and various nanomaterials with good adsorption performances have been prepared during the past decades. In this paper, a variety of novel nanomaterials with excellent adsorption performances for Pb(II) and Cu(II) reported in recent years are reviewed, such as carbon-based materials, clay mineral materials, zero-valent iron and their derivatives, MOFs, nanocomposites, etc. The novel nanomaterials with extremely high adsorption capacity, selectivity and particular nanostructures are summarized and introduced, along with their advantages and disadvantages. And, some future research priorities for the treatment of wastewater are also prospected.

Highly Selective Pb(II) Adsorption by DTPA-Functionalized Graphene Oxide/Carboxymethyl Cellulose Aerogel

Graphene oxide (GO) exhibits a strong adsorption capacity for the removal of heavy metal ions from liquids, making it a topic of increasing interest among researchers. However, a significant challenge persists in the preparation of graphene oxide-based adsorbents that possess both high structural stability and excellent adsorption capacity. In this paper, a green and environmentally friendly ternary composite aerogel based on graphene was successfully synthesized. The adsorption capacity of graphene oxide was enhanced through diethylenetriaminepentaacetic acid modification, while the incorporation of composite carboxymethyl cellulose improved the structural stability of the composite aerogel in liquid. The composite aerogel demonstrates robust interactions between its components and features a multiscale porous structure. Adsorption tests conducted with Pb(II) revealed that the GO/DTPA/CMC (GDC) composite aerogel exhibits a favorable adsorption capacity. The study of adsorption kinetics and isotherms indicated that the adsorption process follows the quasi-secondary adsorption model and Freundlich adsorption model, suggesting a chemical multilayer adsorption mechanism, and the maximum adsorption capacity for Pb(II) ions was 521.917 mg/g based on the quasi-quadratic kinetic model fitting. X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) analyses, performed before and after adsorption, confirmed that the adsorption of Pb(II) primarily occurs through chelation, complexation, proton exchange, and electrostatic interactions between ions and active sites such as hydroxyl and carboxyl groups. This study presents an innovative strategy for simultaneously enhancing the adsorption properties of graphene oxide-based composite aerogels and ensuring solution stability.

Application of machine learning in prediction of Pb2+ adsorption of biochar prepared by tube furnace and fluidized bed

Data mining by machine learning (ML) has recently come into application in heavy metals purification from wastewater, especially in exploring lead removal by biochar that prepared using tube furnace (TF-C) and fluidized bed (FB-C) pyrolysis methods. In this study, six ML models including Random Forest Regression (RFR), Gradient Boosting Regression (GBR), Support Vector Regression (SVR), Kernel Ridge Regression (KRR), Extreme Gradient Boosting (XGB), and Light Gradient Boosting Machine (LGBM) were employed to predict lead adsorption based on a dataset of 1012 adsorption experiments, comprising 422 TF-C groups from our experiments and 590 FB-C groups from literatures. The XGB model showed superior accuracy and predictive performance for adsorption, achieving R2 values for TF-C (0.992) and FB-C (0.981), respectively. Contrasting inferior results were observed in other models, including RF (0.962 and 0.961), GBR (0.987 and 0.975), SVR (0.839 and 0.763), KRR (0.817 and 0.881), and LGBM (0.975 and 0.868). Additionally, a hybrid dataset combining both biochars in Pb adsorption also indicated high accuracy (0.972) as obtained from XGB model. The investigation revealed that the influence of char characteristics and adsorption conditions on Pb adsorption differs between the two biochar. Specific char characteristics, particularly nitrogen content, significantly influence lead adsorption in both biochar. Interestingly, the influence of pyrolysis temperature (PT) on lead adsorption is found to be greater for TF-C than for FB-C. Consequently, careful consideration of PT is crucial when preparing TF-C biochar. These findings offer practical guidance for optimizing biochar preparation conditions during heavy metal removal from wastewater.

Evaluation of the effect of graphene oxide-based nanocomposites on smear layer by a scanning electron microscope: Laboratory investigation

This study is to examine the effect of graphene oxide (GO) and GO-based nanocomposites (GO_EDTA, GO_CHIT) on the smear layer by scanning electron microscopy (SEM). Sixty human single-rooted anterior teeth were used. Samples were randomly categorised into six groups. Distilled water in group 1, 17% EDTA in group 2, chitosan (CHIT) solution in group 3, GO solution in group 4, GO_EDTA solution in group 5 and GO_CHIT in group 6 were used as irrigation solutions. Photomicrographs were acquired from the coronal, middle and apical parts of the samples by SEM. Statistical analyses were performed using Kruskal-Wallis, Mann-Whitney U and Wilcoxon tests. There was a statistically significant difference among the groups (p < 0.003). Adding GO to CHIT and EDTA did not affect removing the smear layer in all segments (p < 0.003). Incorporating GO into EDTA and CHIT solutions did not change their interaction with the smear layer.

Advances in lignin-based biosorbents for sustainable wastewater treatment

The heavy metals, pesticides and dyes in agriculture and industry caused serious water pollution have increased the urgency for the advancement of biomass-based adsorbents due to their merits of low cost, high efficiency, and environmental sustainability. Thus, this review systematically examines the recent progress of lignin-based adsorbents dedicated to wastewater purification. Commencing with a succinct exposition on the intricate structure and prevalent forms of lignin, the review proceeds to expound rational design strategies tailored for lignin-based adsorbents coupled with adsorption mechanisms and regeneration methods. Emphasis is placed on the potential industrial applications of lignin-based adsorbents, accentuating their capacity for recovery and direct utilization post-use. The future challenges and outlooks associated with lignin-based adsorbents are discussed to provide novel perspectives for the development of high-performance and sustainable biosorbents, facilitating the effective removal of pollutants and the value-added utilization of resources in a sustainable manner.

Graphene materials in pollution trace detection and environmental improvement

Water scarcity is a pressing issue experienced in numerous countries and is expected to become increasingly critical in the future. Anthropogenic activities such as mining, agriculture, industries, and domestic waste discharge toxic contaminants into natural water bodies, causing pollution. Addressing these environmental crises requires tackling the challenge of removing pollutants from water. Graphene oxide (GO), a form of graphene functionalized with oxygen-containing chemical groups, has recently garnered renewed interest due to its exceptional properties. These properties include a large surface area, mechanical stability, and adjustable electrical and optical characteristics. Additionally, surface functional groups like hydroxyl, epoxy, and carboxyl groups make GO an outstanding candidate for interacting with other materials or molecules. Because of its expanded structural diversity and enhanced overall properties, GO and its composites hold significant promise for a wide range of applications in energy storage, conversion, and environmental protection. These applications encompass hydrogen storage materials, photocatalysts for water splitting, the removal of air pollutants, and water purification. Serving as electrode materials for various lithium batteries and supercapacitors. Graphene-based materials, including graphene, graphene oxide, reduced graphene oxide, graphene polymer nanocomposites, and graphene nanoparticle metal hybrids, have emerged as valuable tools in energy and environmental remediation technologies. This review article provides an overview of the significant impact of graphene-based materials in various areas. Regarding energy-related topics, this article explores the applications of graphene-based materials in supercapacitors, lithium-ion batteries, and catalysts for fuel cells. Additionally, the article investigates recent advancements in detecting and treating persistent organic pollutants (POPs) and heavy metals using nanomaterials. The article also discusses recent developments in creating innovative nanomaterials, nanostructures, and treatment methods for addressing POPs and heavy metals in water. It aims to present the field's current state and will be a valuable resource for individuals interested in nanomaterials and related materials.

Unveiling the contemporary progress of graphene-based nanomaterials with a particular focus on the removal of contaminants from water: a comprehensive review

Water scarcity and pollution pose significant challenges to global environmental sustainability and public health. As these concerns intensify, the quest for innovative and efficient water treatment technologies becomes paramount. In recent years, graphene-based nanomaterials have emerged as frontrunners in this pursuit, showcasing exceptional properties that hold immense promise for addressing water contamination issues. Graphene, a single layer of carbon atoms arranged in a hexagonal lattice, exhibits extraordinary mechanical, electrical, and chemical properties. These inherent characteristics have led to a surge of interest in leveraging graphene derivatives, such as graphene oxide (GO), reduced graphene oxide and functionalized graphene, for water treatment applications. The ability of graphene-based nanomaterials to adsorb, catalyze, and photocatalyze contaminants makes them highly versatile in addressing diverse pollutants present in water sources. This review will delve into the synthesis methods employed for graphene-based nanomaterials and explore the structural modifications and functionalization strategies implemented to increase their pollutant removal performance in water treatment. By offering a critical analysis of existing literature and highlighting recent innovations, it will guide future research toward the rational design and optimization of graphene-based nanomaterials for water decontamination. The exploration of interdisciplinary approaches and cutting-edge technologies underscores the evolving landscape of graphene-based water treatment, fostering a path toward sustainable and scalable solutions. Overall, the authors believe that this review will serve as a valuable resource for researchers, engineers, and policymakers working toward sustainable and effective solutions for water purification.

Desalination Performance in Janus Graphene Oxide Channels: Geometric Asymmetry vs Charge Polarity

Improving the desalination performance of membranes is always in the spotlight of scientific research; however, Janus channels with polarized surface charge as nanofiltration membranes are still unexplored. In this work, using molecular dynamics simulations, we demonstrate that Janus graphene oxide (GO) channels with appropriate geometry and surface charge can serve as highly efficient nanofiltration membranes. We observe that the water permeability of symmetric Janus GO channels is significantly superior to that of asymmetric channels without sacrificing much ion rejection, owing to weakened ion blockage and electrostatic effects. Furthermore, in symmetric Janus GO channels, the transport of water and ions is sensitive to the charge polarity of the channel inner surface, which is realized by tuning the ratio of cationic and anionic functionalization. Specifically, with the increase in cationic functionalization, the water flux decreases monotonously, while ion rejection displays an interesting maximum behavior that indicates desalination optimization. Moreover, the trade-off between water permeability and ion rejection suggests that the Janus GO channels have an excellent desalination potential and are highly tunable according to the specific water treatment requirements. Our work sheds light on the key role of channel geometry and charge polarity in the desalination performance of Janus GO channels, which paves the way for the design of novel desalination devices.

Fabrication of Mesoporous Silica Nanoparticle-Decorated Graphene Oxide Sheets for the Effective Removal of Lead (Pb2+) from Water

Mesoporous silica nanoparticle-decorated graphene oxide nanosheets (MSiO2-GO) were synthesized and characterized for the active removal of lead (Pb2+) from the water. MSiO2 NPs were prepared via an ultrasonication method using tetraethyl orthosilicate (TEOS), and GO sheets were obtained via a modified Hummers' method. X-ray diffraction, UV-vis spectroscopy, Fourier transform infrared spectroscopy, and energy dispersive X-ray spectroscopy specified the composition of MSiO2 NPs and GO sheets. The surface charge and texture of the MSiO2-GO nanosheets were obtained using the ζ-potential technique and by field emission scanning electron microscopy. The relative cytotoxicity test of MSiO2 NPs and MSiO2-GO nanosheets was performed on Murine Raw 264.7 cells before implying the treatment of water. Adsorption of Pb2+ ions on MSiO2-GO nanosheets was examined at various parameters such as different aqueous pH values (2.0-10.0), MSiO2-GO nanosheet doses (3, 5, 10, 15, 20 mg L-1), time intervals (2-30 min), and temperatures (25-45 °C). About 90% of Pb2+ ions were removed from water within 30 min (MSiO2-GO dose: 15 mg L-1; initial Pb2+ ions: 50 mg L-1; temperature: 25 °C; shaking speed: 200 rpm). The maximal uptake of Pb2+ was obtained at solution pH 6.0. Pseudo-first- and pseudo-second-order kinetic rate equations describe the sorption dynamic data. Pb2+ sorption isotherms were modeled using the Freundlich and Langmuir isotherm models. The possible mechanism of binding of Pb2+ ions onto MSiO2-GO nanosheets has been discussed. The exhausted MSiO2-GO nanosheets were successfully regenerated using 0.005 M HNO3 as the desorbing agent.

Simultaneous removal of phosphorus, zinc, and lead from oligotrophic ecosystem by iron-driven denitrification: Performance and mechanisms

Based on the current situation of complex pollution caused in surface water by oligotrophic condition and heavy metal release from river and lake bottom sediments. This study aimed to achieve the simultaneous removal of nitrate, phosphorus, Zn2+ and Pb2+ through microbial approach. At nitrate concentration of 4.82 mg L-1, carbon to nitrogen ratio of 1.5, pH of 6.0, and Fe2+ concentration of 5.0 mg L-1, the nitrate removal efficiency of Zoogloea sp. FY-6 reached 95.17%. The addition of pollutants under these conditions resulted in 88.76% removal of total phosphorus at 18 h, and 85.46 and 78.59% removal of Zn2+ and Pb2+ respectively, and there was competition for adsorption between Zn2+ and Pb2+. Extracellular polymers and fluorescence excitation-emission substrates confirmed that Fe2+ reduced heavy metal toxicity through promoting bacterial production of secretions and promotes denitrification as a carbon source. Meanwhile, contaminant removal curves and Fourier transform infrared spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy demonstrated the synchronous removal of Zn2+ and Pb2+ mainly through biological action and the formation of nanoscale iron oxides. Biological-iron precipitation also provided adsorption sites for phosphorus. This research provides the theoretical foundation for applying microorganisms to restore oligotrophic source water (rivers and lakes) containing complex pollutants.

Ionic transport through a bilayer nanoporous graphene with cationic and anionic functionalization

Understanding the ionic transport through multilayer nanoporous graphene (NPG) holds great promise for the design of novel nanofluidic devices. Bilayer NPG with different structures, such as nanopore offset and interlayer space, should be the most simple but representative multilayer NPG. In this work, we use molecular dynamics simulations to systematically investigate the ionic transport through a functionalized bilayer NPG, focusing on the effect of pore functionalization, offset, applied pressure and interlayer distance. For a small interlayer space, the fluxes of water and ions exhibit a sudden reduction to zero with the increase in offset that indicates an excellent on-off gate, which can be deciphered by the increasing potential of mean force barriers. With the increase in pressure, the fluxes increase almost linearly for small offsets while always maintain zero for large offsets. Finally, with the increase in interlayer distance, the fluxes increase drastically, resulting in the reduction in ion rejection. Notably, for a specific interlayer distance with monolayer water structure, the ion rejection maintains high levels (almost 100% for coions) with considerable water flux, which could be the best choice for desalination purpose. The dynamics of water and ions also exhibit an obvious bifurcation for cationic and anionic functionalization. Our work comprehensively addresses the ionic transport through a bilayer NPG and provides a route toward the design of novel desalination devices.

A review on adsorption of heavy metals from wastewater using carbon nanotube and graphene-based nanomaterials

The rampant rise in world population, industrialization, and urbanization expedite the contamination of water sources. The presence of the non-biodegradable character of heavy metals in waterways badly affects the ecological balance. In this modern era, the unavailability of getting clear water as well as the downturn in water quality is a major concern. Therefore, the effective removal of heavy metals has become much more important than before. In recent years, the attention to better wastewater remediation was directed towards adsorption techniques with novel adsorbents such as carbon nanomaterials. This review paper primarily emphasizes the fundamental concepts, structures, and unique surface properties of novel adsorbents, the harmful effects of various heavy metals, and the adsorption mechanism. This review will give an insight into the current status of research in the realm of sustainable wastewater treatment, applications of carbon nanomaterials, different types of functionalized carbon nanotubes, graphene, graphene oxide, and their adsorption capacity. The importance of MD simulations and density functional theory (DFT) in the elimination of heavy metals from aqueous media is also discussed. In addition to that, the effect of factors on heavy metal adsorption such as electric field and pressure is addressed.

Facile activation of natural calcium-rich sepiolite with oxalic acid for selective Pb(II) removal: Highly-efficient performance, mechanisms and site energy distribution

The design and development of adsorbents with high efficiency, selectivity, and economy for Pb(II) are essential to environmental governance and ecological safety. Herein, an oxalic acid (OA) activated natural sepiolite (nSEP) composite for highly efficient Pb(II) removal was prepared by a facile impregnation strategy. The OA activated nSEP nanocomposite (OA-nSEP) was characterized by various instrumental techniques and its adsorption performance towards Pb(II) was further evaluated through a series of static and dynamic experiments under various environmental conditions. Results revealed that OA reacted with the calcium impurities in nSEP to form calcium oxalate, causing mesoporous structure and larger specific surface area of OA-nSEP. The obtained OA-nSEP possessed super high Pb(II) adsorption capacities (858.4-1252 mg/g), which were much higher than that of most modified clays or conventional materials. The average adsorption site energy and the standard deviation of the site energy distribution were analyzed to investigate the strength of Pb(II) binding onto OA-nSEP and the adsorption site heterogeneity. Mechanism studies confirmed that oxalate groups exerted a primary role in the adsorption process. X-ray diffraction and X-ray photoelectron spectrometry (XPS) unveiled that the coordination of oxalate with Pb(II) and precipitation of lead oxalate was responsible for the high efficiency and selectivity. Distinguishing feature of high adsorption capacity, specific selective adsorption, abundant availability, and splendid reusability make the OA-nSEP a promising candidate for eliminating Pb(II) in practical scenarios.

Nano iron tetroxide-modified rice husk biochar promoted Feammox performance of Klebsiella sp. FC61 and synergistically removed Ni2+ and ciprofloxacin

The iron reduction coupled with ammonia oxidation process (Feammox) is a biological reaction process associated with the nitrogen cycle that has been discovered in recent years. In this study, the iron-reducing bacterium Klebsiella sp. FC61 was attached by synthesizing nano-loadings of iron tetroxide (nFe₃O₄) onto rice husk biochar (RBC), and the RBC-nFe₃O₄ was used as an electron shuttle to participate in the biological iron reduction process of soluble and insoluble Fe³⁺ to improve the ammonia oxidation efficiency to 81.82%. This acceleration of electron transfer increased the carbon consumption rate and further tuned up the COD removal efficiency to 98.00%. The Feammox could be coupled with iron denitrification for internal nitrogen/iron cycling to reduce the accumulation of nitrate by-products and achieve the recycling of iron. In addition, pollutants such as Ni²⁺, ciprofloxacin, and formed chelates could be removed by pore adsorption and π-π interactions using bio-iron precipitates produced by iron-reducing bacteria.

Application of Poly(caffeic acid) for the Extraction of Critical Rare Earth Elements

Poly(caffeic acid) was synthesized and utilized for the extraction and determination of rare earth elements (REEs), thorium, and uranium. Oxidative polymerization of caffeic acid, a low-cost plant-based material, in the presence of ethylenediamine produced a granular, air-stable, and cross-linked polymer. The polymer is highly oxygenated and together with the amino group from ethylenediamine efficiently coordinates and preconcentrates these critical elements from aqueous media. Extraction was dependent on solution pH, amount of sorbent, and extraction time, while the concentration and flow rate of the desorption solution governed the recovery efficiency. Removal and recovery efficiencies greater than 98 and 90%, respectively, and low levels of detection ranging from 0.1 to 2.9 ng/L were achieved. Determination of these strategic elements in the presence of potentially interfering ions as well as in complex matrices such as well water and produced water samples also was demonstrated. The capacity of poly(caffeic acid) was determined with lanthanum as a representative REE to be 161.7 mg/g, establishing the promise of poly(caffeic acid) for larger-scale extractions in addition to the ability to screen sources for the presence of REEs.

Superior Heavy Metal Ion Adsorption Capacity in Aqueous Solution by High-Density Thiol-Functionalized Reduced Graphene Oxides

The preparation of mercapto-reduced graphene oxides (m-RGOs) via a solvothermal reaction using P₄S₁₀ as a thionating agent has demonstrated their potential as an absorbent for scavenging heavy metal ions, particularly Pb²⁺, from aqueous solutions due to the presence of thiol (-SH) functional groups on their surface. The structural and elemental analysis of m-RGOs was conducted using a range of techniques, including X-ray diffraction (XRD), Raman spectroscopy, optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), scanning transmission electron microscopy equipped with energy-dispersive spectroscopy (STEM-EDS), and X-ray photoelectron spectroscopy (XPS). At pH 7 and 25 °C, the maximum adsorption capacity of Pb²⁺ ions on the surface of m-RGOs was determined to be approximately 858 mg/g. The heavy metal-S binding energies were used to determine the percent removal of the tested heavy metal ions, with Pb²⁺ exhibiting the highest percentage removal, followed by Hg²⁺ and Cd²⁺ ions having the lowest percent removal, and the binding energies observed were Pb-S at 346 kJ/mol, Hg-S at 217 kJ/mol, and Cd-S at 208 kJ/mol. The time-dependent removal study of Pb²⁺ ions also yielded promising results, with almost 98% of Pb²⁺ ions being removed within 30 min at pH 7 and 25 °C using a 1 ppm Pb²⁺ solution as the test solution. The findings of this study clearly demonstrate the potential and efficiency of thiol-functionalized carbonaceous material for the removal of environmentally harmful Pb²⁺ from groundwater.

A review of novel green adsorbents as a sustainable alternative for the remediation of chromium (VI) from water environments

The presence of heavy metal, chromium (VI), in water environments leads to various diseases in humans, such as cancer, lung tumors, and allergies. This review comparatively examines the use of several adsorbents, such as biosorbents, activated carbon, nanocomposites, and polyaniline (PANI), in terms of the operational parameters (initial chromium (VI) concentration (C_o), temperature (T), pH, contact time (t), and adsorbent dosage) to achieve the Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption. The study finds that the use of biosorbents (fruit bio-composite, fungus, leave, and oak bark char), activated carbons (HCl-treated dry fruit waste, polyethyleneimine (PEI) and potassium hydroxide (KOH) PEI-KOH alkali-treated rice waste-derived biochar, and KOH/hydrochloric acid (HCl) acid/base-treated commercial), iron-based nanocomposites, magnetic manganese-multiwalled carbon nanotubes nanocomposites, copper-based nanocomposites, graphene oxide functionalized amino acid, and PANI functionalized transition metal are effective in achieving high Langmuir's maximum adsorption capacity (q_m) for chromium (VI) adsorption, and that operational parameters such as initial concentration, temperature, pH, contact time, and adsorbent dosage significantly affect the Langmuir's maximum adsorption capacity (q_m). Magnetic graphene oxide functionalized amino acid showed the highest experimental and pseudo-second-order kinetic model equilibrium adsorption capacities. The iron oxide functionalized calcium carbonate (IO@CaCO₃) nanocomposites showed the highest heterogeneous adsorption capacity. Additionally, Syzygium cumini bark biosorbent is highly effective in treating tannery industrial wastewater with high levels of chromium (VI).

Optimization of the effect of microelectrodes on Ni2+ removal in three-dimensional electrode system

This study investigated Ni⁺² removal performance in 3DER reactors where electrocoagulation mechanisms and microelectrodes are used together. EDTA modification was carried out on the granule-activated carbon surface to increase the efficiency and affinity of microelectrodes against Ni⁺² molecules. The grafting was examined using BET, FT-IR, SEM, EDS, and the elemental mapping methods. With the surface analyses made in this study, it was revealed that EDTA modification on granulated activated carbon was successfully performed. Also, 8.48%wt by mass of EDTA grafting on granular activated carbon was possible. EDTA functionalization did not affect the surface pore structures of CAC much. Under 10 V potential, 97.82% Ni removal efficiency was obtained with 2D in 35 min, while 96.69% removal in 10 min and 100% removal in 15 min were obtained in the 3D reactor. The Ni⁺² removal mechanism in 3DER reactors has been determined to conform to the pseudo-second-order kinetic model. The k₂ value obtained for 10 V (1.36 10^-2) is 27 times the k₂ value obtained for 5 V for 3DER reactors. In addition, using central composite design (CCD), operational parameters such as time, concentration, and potential difference affecting Ni⁺² removal in 3DER reactors have been optimized. The most influential parameter is the applied voltage, followed by time and concentration. It has been determined that 3DER reactors using EDTA-modified microelectrodes are highly efficient and suitable for Ni⁺² removal.

Graphene-based materials for effective adsorption of organic and inorganic pollutants: A critical and comprehensive review

Water scarcity has been felt in many countries and will become a critical issue in the coming years. The release of toxic organic and inorganic contaminants from different anthropogenic activities, like mining, agriculture, industries, and domestic households, enters the natural waterbody and pollutes them. Keeping this in view in combating the environmental crises, removing pollutants from wastewater is one of the ongoing environmental challenges. Adsorption technology is an economical, fast, and efficient physicochemical method for removing both organic and inorganic pollutants, even at low concentrations. In the last decade, graphene and its composite materials have become the center of attraction for numerous applications, including wastewater treatment, due to the large surface area, highly active surface, and exclusive physicochemical properties, which make them potential adsorbents with unique physicochemical properties, like low density, chemical strength, structural variability, and the possibility of large-scale fabrications. This review article provides a thorough summary/critical appraisal of the published literature on graphene-, GO-, and rGO-based adsorbents for the removal of organic and inorganic pollutants from wastewater. The synthesis methods, experimental parameters, adsorption behaviors, isotherms, kinetics, thermodynamics, mechanisms, and the performance of the regeneration-desorption processes of these substances are scrutinized. Finally, the research challenges, limitations, and future research studies are also discussed. Certainly, this review article will benefit the research community by getting substantial information on suitable techniques for synthesizing such adsorbents and utilizing them in water treatment and designing water treatment systems.

Reusable Sugar-Based Gelator for Marine Oil-Spill Recovery and Waste Water Treatment

In this work, the gelation ability of a series of novel pyridine-based glucose tailored gelators (DPHAEN, DPHABN, and DPHAHN) with a flexible alkyl chain has been examined in binary solvent mixtures using a number of techniques, for example, UV spectroscopy, FT-IR spectroscopy, NMR spectroscopy, rheology measurement, SEM, XRD, and computational study. Proposed herein is an environment-friendly method to realize toxic dye separation and oil/water separation. It has been found that gels in a selective binary solvent mixture are efficient reusable absorbers of toxic dye molecules. A new gravitational force-driven, simple one-step, toxic dye removal and oil-water separation method is presented for sustainable filtration of waste water and simultaneous collection of oil. The gel column also showed high stability and reusability over repeated use and can be easily scaled for efficient clean-up of a large number of toxic dyes and oil spills present in water. Studies also exposed that the gel column can simultaneously separate dye molecules and mineral oils from water. This simple, green, and efficient method overcomes a nontrivial hurdle for environmentally safe separation of toxic dyes as well as oil/water mixtures and offers insights into the design of advanced materials for practical oil/water separation.

Recent progresses, challenges, and opportunities of carbon-based materials applied in heavy metal polluted soil remediation

The application of carbon-based materials (CBMs) for heavy metal polluted soil remediation has gained growing interest due to their versatile properties and excellent remediation performance. Although the progresses on applications of CBMs in removing heavy metal from aqueous solution and their corresponding mechanisms were well known, comprehensive review on applications of CBMs in heavy metal polluted soil remediation were less identified. Therefore, this review provided insights into advanced progresses on utilization of typical CBMs including biochar, activated carbon, graphene, graphene oxide, carbon nanotubes, and carbon black for heavy metal polluted soil remediation. The mechanisms of CBM remediation of heavy metals in soil were summarized, mainly including physical adsorption, precipitation, complexation, electrostatic interaction, and cationic-π coordination. The key factors affecting the remediation effect include soil pH, organic matter, minerals, microorganisms, coexisting ions, moisture, and material size. Disadvantages of CBMs were also included, such as: potential health risks, high cost, and difficulty in achieving co-passivation of anions and cations. This work will contribute to our understanding of current research advances, challenges, and opportunities for CBMs remediation of heavy metal-contaminated soils.

Simultaneous Quantitation of Lead and Cadmium on an EDTA-Reduced Graphene Oxide-Modified Glassy Carbon Electrode

Cadmium (Cd) and lead (Pb) are classified as category one toxicants. The provisional guideline values, according to the World Health Organization (WHO), for Cd and Pb are 3 and 10 ppb, respectively. An easy, quick, and cheap analytical technique is in demand for the determination of these toxic heavy metals in water. Hence, a novel electrochemical sensing platform is developed by modifying the glassy carbon electrode with ethylenediaminetetraacetic acid (EDTA)-functionalized reduced graphene oxide (ErGO) for the low-cost simultaneous quantitation of toxic heavy-metal ions, lead and cadmium, in real water samples. EDTA is grafted to the surface of graphene oxide, via amine linkage, and the oxygen functionality is reduced by a green agent, tyrosine. Various physical and electrochemical characterizations of the as-prepared electrocatalytic material were performed by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), ζ-potential, ultraviolet diffuse reflectance spectroscopy (UV-DRS), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), etc. The glassy carbon electrode (GCE) is modified with ErGO by a simple drop-casting method for simultaneous metal-ion quantitation by differential pulse voltammetry (DPV). EDTA functionalization of graphene oxide and its further reduction using the green agent enhance the stability and sensitivity of the electrode substrate. The limits of detection for cadmium and lead ions calculated for ErGO/GCE are 1.02 and 2.52 ppb, while the limits of quantification for lead and cadmium ions are 3.41 and 8.4 ppb, and their sensitivities are 0.8 and 0.6 nA/ppb, respectively. Real river water contains 200.2 ± 0.38 ppb of Pb²⁺ ions (mean ± stdev, n = 3) by the DPV technique, which is validated by ICP-OES analysis.

Environmental application of amine functionalised magnetite nanoparticles grafted graphene oxide chelants

This study proposed a two-step method involving hydrothermal and electrostatic self-assembly processes for synthesising an amine-functionalised magnetic ligand graphene oxide-based nanocomposite (EDTA@Fe₃O₄@GO). The amine groups were successfully attached to the surface of iron (II, III) oxide (Fe₃O₄), which were embedded on the surface of graphene oxide (GO) (Fe₃O₄@GO). This EDTA@ Fe₃O₄@GO nanocomposite was used as a chelating agent to bind the toxic heavy metal ions. EDTA@Fe₃O₄@GO demonstrated the synergistic effect between the large surface area and magnetic behaviour of Fe₃O₄@GO and the chelating effect of EDTA, and it showed higher efficiency than the individual GO and Fe₃O₄. The possible structural and compositional characteristics were proposed based on Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) and Raman spectroscopy analysis. The outcomes revealed the mechanism behind the excellent As(V) adsorption onto EDTA@Fe₃O₄@GO. The adsorption process was studied by fitting the experimental data obtained into various kinetic and isotherm models. The pseudo-second-order (PSO) kinetic model and the Freundlich isotherm model (FIM) were found to be the best fit models for the removal of As(V) by EDTA@Fe₃O₄@GO. EDTA@Fe₃O₄@GO has the utmost adsorption capacity of 178.4 mg/g. Furthermore, the EDTA@Fe₃O₄@GO nanocomposite is reusable, and it showed excellent adsorption capacity up to 5 cycles. This study has provided insight into the potential of EDTA@Fe₃O₄@GO and its applications in large-scale wastewater treatment.

Adsorption of Orange G in Liquid Solution by the Amino Functionalized GO

Dye effluent damaged the water environment and human health with its massive discharge. In order to eliminate dye from the water environment, a variety of adsorbents were used to investigate dye removal. Graphene oxide (GO) attracted extensive attention due to its excellent surface property in the degradation of dye wastewater. Modified GO with multifunctional groups helped to improve adsorption performance. 3-Aminopropyltriethoxysilane modified GO (AS-GO) was fabricated for the removal of Orange G (OG) in this study. The results showed that AS-GO had an excellent adsorption ability of OG. During the reaction process, the maximum adsorptive capacity of OG was up to 576.6 mg/g at T = 313 K and pH = 3 with the initial OG concentration of 100 mg/L and the initial adsorbent dose of 2.5 g/L. The adsorption kinetic process of AS-GO conformed to the pseudo-second-order and Langmuir models. The spontaneous and endothermic adsorption of OG occurred in the adsorption process. The main adsorption mechanisms were electrostatic, π–π and hydrogen bonding interactions in the reaction process. After four cycles of AS-GO, it maintained high removal efficiency owing to its remarkable stability. The scheme of GO modified with AS could hinder the agglomeration of GO and provide more active sites, which would further enhance the adsorption properties and expand its application in water purification.

A microfluidic electrochemical sensing platform for in situ detection of trace cadmium ions

Among various detection and analysis platforms, a microfluidic chip-based electrochemical sensing detection platform is a new type of detection platform. In this study, a microfluidic electrochemical detection platform for cadmium ion detection is proposed, and the performance of the detection platform is optimized in terms of both the microchannel size and electrode modifications. The detection mixing processes of the detector with different microchannel sizes, including the concentration distribution in the channel, pressure decay variation and electrolyte current density variation in the detector, were investigated by finite element model calculations. The analysis shows that the size of the microchannel in the detector affects the fluid and thus further affects the chemical reaction. If the size of the electrode does not match the size of the microchannel, insufficient sample volume will lead to inaccurate measurements, reduced sensitivity and increased detection limits. It was found that the sensitivity of the electrochemical sensor was highest when the size of the microchannel in the chip was 400 μm. After optimization, the optimal detection limit for cadmium ions was 0.03 μg L^-1 (S/N = 3). The proposed sensing platform is simple in design and stable in structure, and is suitable for field screening and rapid response to heavy metal contamination events.

Promotion effect of graphene on phytoremediation of Cd-contaminated soil

Echinacea purpurea (L.) Moench was selected as a remediation plant in this study, and different concentrations of graphene oxide (GO) were added to Cd-contaminated soil. Through pot experiments, the effect of E. purpurea on Cd-contaminated soil was determined at 60 days, 120 days, and 150 days. A preliminary study on the remediation mechanism of GO was explored through changes in the forms of Cd in the rhizosphere soil, soil pH, and soil functional groups. Results showed that the optimal concentration of GO was 0.4 g/kg, and under the condition, the accumulation of Cd in the roots of E. purpurea was as high as 113.69 ± 23.86 mg/kg, and the maximum EF reached 5.87 ± 1.34. Compared with those of the control group, accumulated Cd concentration and EF in the roots increased by 60.34% and 2.32, respectively. Correlation analysis showed that the absorption and accumulation of Cd was negatively correlated with the exchangeable Cd content at 120 days, and the exchangeable Cd was negatively correlated with the relative content of functional groups in the soil with 0.4 g/kg GO (E2). The artificial application of GO to the soil can be used as an effective way to improve the effect of E. purpurea in the remediation of Cd soil pollution, and it has great application potential in the stabilization of plants and vegetations and restoration of high-concentration Cd-contaminated soil.

Removal of toxic metals from wastewater environment by graphene-based composites: A review on isotherm and kinetic models, recent trends, challenges and future directions

Access to clean water has reduced in recent years due to pollution and man-made activities. Wastewater treatment regimens are many such as electrocoagulation, adsorption, ozonation, membrane and advanced oxidation processes. Owing to economical, resource availability and ease of operation adsorption has upper hand over all other methods employed in wastewater treatment. Graphene based adsorbents attracted researchers due to their ability to play dual role as adsorbent and photo-catalysts. When it comes to removal of heavy metals and dyes graphene-based aerogels are successful. Graphene composites were predominantly synthesized by top-down and bottom-up approach methods. Graphene composites are mesoporous and have microporous structure on surface. Graphene has copper desorption efficiency of 90 % upon 10th consecutive cycle. Graphene based adsorbents have adsorption efficiency of 367, 246 and 106.3 mg^-1 for lead, zinc and cadmium respectively. Though graphene possesses numerous applications, this review was devoted towards heavy metals removal from aqueous environment. In detail, the synthesis routes and interaction mechanism were explained and also the adsorption isotherms, kinetics were added. This review will serve as support for future research directions on removal of wastewater contaminants (heavy metals).

Simultaneous removal of nitrate, tetracycline, and Pb(II) by iron oxidizing strain Zoogloea sp. FY6: Performance and mechanism

Based on the prevalence of combined antibiotics and heavy metals contamination in the aquatic environment, this study utilized a microbial approach to achieve simultaneous removal of nitrate (NO₃^--N), tetracycline (TTC), and Pb(II). Zoogloea sp. FY6 could achieve an optimal NO₃^--N removal efficiency of 91.5% under C/N ratio of 2.0, at a pH of 6.3, and Fe(II) concentration of 20.23 mg L^-1 based on response surface methodology. Additionally, strain FY6 was further found to achieve 89.9 and 81.7% removal of TTC and Pb(II) at 6 h under the optimal conditions. Finally, the results of Fluorescence excitation-emission matrix, X-ray diffraction, Fourier transform infrared spectrometer, and X-ray photoelectron spectroscopy further proved that the biologically formed nanoscale iron oxides and biological action jointly led to the removal of TTC and Pb(II). This study provided a theoretical basis for the application of microbially driven process to remove multi-pollutants in micro-polluted water bodies.

Hierarchical Nanoflowers of MgFe2O4, Bentonite and B-,P- Co-Doped Graphene Oxide as Adsorbent and Photocatalyst: Optimization of Parameters by Box–Behnken Methodology

In the present study, nanocomposites having hierarchical nanoflowers (HNFs) -like morphology were synthesized by ultra-sonication approach. HNFs were ternary composite of MgFe₂O₄ and bentonite with boron-, phosphorous- co-doped graphene oxide (BPGO). The HNFs were fully characterized using different analytical tools viz. X-ray photoelectron spectroscopy, scanning electron microscopy, energy dispersion spectroscopy, transmission electron microscopy, X-ray diffraction, vibrating sample magnetometry and Mössbauer analysis. Transmission electron micrographs showed that chiffon-like BPGO nanosheets were wrapped on the MgFe₂O₄-bentonite surface, resulting in a porous flower-like morphology. The red-shift in XPS binding energies of HNFs as compared to MgFe₂O₄-bentoniteand BPGO revealed the presence of strong interactions between the two materials. Box–Behnken statistical methodology was employed to optimize adsorptive and photocatalytic parameters using Pb(II) and malathion as model pollutants, respectively. HNFs exhibited excellent adsorption ability for Pb(II) ions, with the Langmuir adsorption capacity of 654 mg g⁻¹ at optimized pH 6.0 and 96% photocatalytic degradation of malathion at pH 9.0 as compared to MgFe₂O₄-bentonite and BPGO. Results obtained in this study clearly indicate that HNFs are promising nanocomposite for the removal of inorganic and organic contaminants from the aqueous solutions.

Synthesis of Amidoxime Adsorbent by Radiation-Induced Grafting of Acrylonitrile/Acrylic Acid on Polyethylene Film and Its Application in Pb Removal

In the aquatic environment, heavy metals such as lead ions Pb (II) are of particular importance. These are due to Pb (II) being toxic at concentrations over 0.01 mg/L, when taken continuously over an extended length of time. Organs including the heart, gut, and kidneys are seriously harmed by Pb (II) intoxication. The neurological, reproductive, and bone systems are also affected. The removal of Pb (II) from aquatic environments is, therefore, crucial. Low density Polyethylene (LDPE) is grafted by radiation with Acrylonitrile and acrylic acid (PE-g-AN/AAc) for the adsorption of Pb (II). Factors that control the grafting process for optimum conditions, such as the effect of solvents, the air atmosphere, inhibitors, comonomer concentration, and composition and irradiation dose, are studied to obtain a high grafting yield without homopolymer formation and a higher water uptake. The results showed that the addition of 2.5% by wt% ferric chloride salt effectively inhibits homoploymerization of a mixture of 30% methanol and 70% H₂O used as a solvent in nitrogen. The highest graft yield obtained was 320% at a 25 kGy radiation dose with an 80/20 monomer composition and 60% comonomer concentration. The resulting composite films were characterized by XRD to analyze the dispersion properties of the material, SEM for the surface morphology, FTIR analysis for the functional groups, TGA, DSC for the thermal stability and elongation, and tensile strength for the mechanical properties. The uptake of Pb (II) from lead nitrate aqueous solution by (PE-g-AN/AAc) was observed under different conditions of the degree of grafting, contact time, metal ion concentration, and pH. The results obtained suggest LDPE-g-p (AN/AAc) as a superabsorbent for the Pb (II) ion’s removal from an aqueous solution.

How UV radiation and pH alternation impact graphene oxide mediated environmental toxicant adsorption and resulting safety characteristics - A toxicology study beyond a classic carrier effect

Once released into water, the widely used graphene oxide (GO) is likely to adsorb classical environmental pollutants, exemplified by Microcystin-LR (MCLR) that is a representative double-bond rich liver-toxic endotoxin. While GO-mediated carrier effect is fairly predictable, the involvement of environmental factors like UV and pH may add additional level of sophistication as these factors may impact the adsorption capacity of GO to MCLR. Here, we firstly investigated the changes of GO structure under different UV-radiation durations and pH conditions with a view to establish the correlation in terms of MCLR adsorption onto GO. We demonstrated that GO reduction especially oxygen-containing groups reduction induced by UV- radiation caused the compromised adsorption MCLR capacity on GO. Besides, the higher pH decreased the non-biological MCLR adsorption to GO by reducing GO defect sites and increasing electrostatic repulsion. These abiotic discoveries were further investigated to compare the safety features of GO-MCLR complex. Under dark condition (pH = 7), we revealed the cytotoxicity of GO-MCLR to normal liver cells, which involved the ROS generation and cell ferroptosis caused by Fe²⁺ accumulation. Introduction of UV and pH alternation in environment impacted GO-mediated environmental toxicant adsorption and resulting safety characteristics, which reminded us environmental factors should not be ignored in the GO-mediated carrier effect.

Efficient mercury removal from aqueous solutions using carboxylated Ti3C2Tx MXene

Water supplies contaminated with heavy metals are a worldwide concern. MXenes have properties that make them attractive for the removal of metal ions from water. This work presents a simple one-step method of Ti₃C₂T_x carboxylation that involves the use of a chelating agent with a linear structure, providing strong carboxylic acid groups with high mobility. The carboxylation decreases the zeta-potential of Ti₃C₂T_x by ~16 to ~18 mV over a pH range of 2.0-8.5 and improves Ti₃C₂T_x stability in the presence of molecular oxygen. pH in the range of 2-6 has a negligible effect on the adsorption capacity of Ti₃C₂T_x and COOH-Ti₃C₂T_x. Compared to Ti₃C₂T_x, COOH-Ti₃C₂T_x has a slightly higher and much faster mercury uptake, and the concentration of mercury ions leached out from COOH-Ti₃C₂T_x is lower. For both Ti₃C₂T_x and COOH-Ti₃C₂T_x, the leached mercury ion concentration is far below the U.S.-EPA maximum level. At an initial Hg²⁺ concentration of 50 ppm and pH of 6, COOH-Ti₃C₂T_x has the equilibrium adsorption capacity of 499.7 mg/g and removes 95% of Hg²⁺ in less than 1 min. Moreover, it has an equilibrium time of 5 min, which is significantly shorter than that of Ti₃C₂T_x (~ 60 min). Finally, its mercury-ion uptake capacity is higher than commercially available adsorbents reported in the literature. Its mercury removal is mainly via chemisorption and monolayer adsorption.

Highly efficient surface sequestration of Pb2+ and Cr3+ from water using a Mn3O4 anchored reduced graphene oxide: Selective removal of Pb2+ from real water

Owing to the ubiquitous existence of detrimental heavy metals in the environment, simple adsorption-oriented approaches are becoming increasingly appealing for the effective removal of Pb²⁺ and Cr³⁺ from water bodies. These techniques use nanocomposites (NC) of reduced graphene oxide (rGO) and Mn₃O₄ (rGO-Mn₃O₄), they employ a hydrothermal technique featuring NaBH₄ and NaOH solutions. Here, spectroscopic and microscopic instrumental techniques were used to evaluate the morphological and physicochemical characteristics of prepared reduced graphene oxide manganese oxide (rGO-Mn₃O₄), revealing that it possessed a well-defined porous structure with a specific surface area of 126 m² g^-1. The prepared rGO-Mn₃O₄ had significant adsorption efficiencies for Pb²⁺ and Cr³⁺, achieving maximum sequestration capacities of 130.28 and 138.51 mg g^-1 for Pb²⁺ and Cr³⁺, respectively, according to the Langmuir model. These adsorption capacities are comparable to or greater than those of previously reported graphene-based materials. The Langmuir isotherm and pseudo-second-order models adequately represented the experimental results. Thermodynamic analysis revealed that adsorption occurred through spontaneous endothermic reactions. Recycling studies showed that the developed r-GO-Mn₃O₄ had excellent recyclability, with <70% removal at the 5th cycle; its feasibility was evaluated using industrial wastewater, suggesting that Pb²⁺ was selectively removed from Pb²⁺ and Cr³⁺ contaminated water. The instrumental analysis and surface phenomena studies presented here revealed that the adsorptive removal processes of both heavy metals involved π electron donor-acceptor interactions, ion exchange, and electrostatic interactions, along with surface complexation. Overall, the developed rGO-Mn₃O₄ has the potential to be a high-value adsorbent for removing heavy metals.

Synergetic removal of thallium and antimony from wastewater with jacobsite-biochar-persulfate system

Both of thallium (Tl) and antimony (Sb) are toxic elements in the natural environment. Emerging Tl and Sb pollution in water has gradually gained public concerns globally. However, limited technologies are available for co-removal of Tl and Sb from wastewater. Herein, an novel system was successfully fabricated to enhance the synergetic removal of both Tl and Sb in wastewater. In this study, MnFe₂O₄-biochar composite (MFBC) facilely synthesized by a one-pot hydrothermal method was used as adsorbent and persulfate (PS) activator for simultaneously removing Tl and Sb from wastewater. The optimal reaction conditions for best removal efficiency of Tl and Sb simultaneously were obtained by using the response surface design combined with Box-Behnken Design (BBD) model. Results unveiled that the average removal rates of Tl and Sb can achieve 98.33% and 89.14%, respectively under the optimal reaction conditions. Electron Spin Resonance (ESR), and radical quenching experiments showed that OH^• and SO₄^•- play a critical role in the removal of Tl-Sb compound pollution. Via using different characterization, it is revealed that the mechanism of removing Tl-Sb containing wastewater by MFBC-1.4/PS system is oxidation, adsorption, complexation and ion exchange. All these results indicate that MFBC-1.4/PS technology is prospective in highly effective removal of Tl and Sb from wastewater simultaneously.

Superior adsorption performance of citrate modified graphene oxide as nano material for removal organic and inorganic pollutants from aqueous solution

This work addressed one step preparation method to form a novel nano material composite of graphene oxide nanosheet (GO) functionalized with low-cost tri-sodium citrate (C), using, teteraethylorthosilicate (TEOS) as a cross-linker. The prepared composite (GO–C) was characterized using various advanced techniques. Among these techniques, the TGA provided interesting information concerning the functionalization process. Within this process, the (–OH) groups that located at the GO-surface were consumed in the modification process which leads to increase the thermal stability of the resulted composite. Cationic organic methylene blue (MB) and crystal violet (CV), and inorganic copper (Cu²⁺) and cobalt (Co²⁺) pollutants were displayed as a model to assess their removal performance by the developed composite (GO–C) from aqueous solution, through batch technique. According to Langmuir isotherm the GO–C present an excellent adsorption capacity for MB (222.22 mg g⁻¹), CV (270.27 mg g⁻¹), Cu²⁺ (163.4 mg g⁻¹) and Co²⁺ (145.35 mg g⁻¹) which were more than the adsorption capacities found in literature. Additionally, the regenerated composite presents higher removal ability than the original composite.

Synergetic removal of oppositely charged dyes by co-precipitation and amphoteric self-floating capturer: Mechanism investigation by molecular simulation

The adsorption performances of adsorbents to dyes are hard to maintain in a wide pH range because most of the reactions are pH-dependent, developing a cost-effective strategy to break the pH-limitation is significant. In this study, an amphoteric self-floating adsorbent (Am-SA) was synthesized by hollow silica microsphere surface modification, which was useful to capture anionic acid orange 7 (AO7) and cationic crystal violet (CV) dyes, but the adsorption performances were also greatly affected by pH. Fortunately, a co-precipitation phenomenon was noticed when the AO7 and CV solutions were mixed with a 1:1 molecule ratio. The precise structures of AO7 and CV molecules were constructed and the AO7-CV-H₂O mixed system was structured by Materials Studio. Besides, this system was involved in a dynamic simulation to reveal the mechanism of the co-precipitation phenomenon. The simulation results showed H₂O molecules dispersed out of the system via thermal motions within 30 ps, but the AO7 and CV molecules aggregated to each other via electrostatic attractions. The energy calculations also demonstrated the electrostatic attraction between AO7 and CV is the dominant factor that induced the aggregation. The aggregation phenomena were also observed in various mixed cationic-anionic dyes systems. The removals of dyes significantly improved in a wide pH range in the mixed systems as the captures of the aggregated dye clusters were much easier than that of independent dye molecules, and both co-precipitation and adsorption contributed to it. Proper utilization of the aggregation behaviors between dyes can be regarded as a prospective strategy in cost-effective treatments.

Determination of the Cadmium Ions from Aqueous Solution Using EDTA Functionalized Prunus Dulcis L. Peels by Solid-Phase Extraction Method

In the present study, Prunus Dulcis L. Peels was modified with ethylenedinitrilo tetraacetic acid and used as the sorbent for the preconcentration of Cd(II) ions from aqueous media. To characterize the sorbent, scanning electron microscopy-energy dispersive X-ray spectrometer and Fourier transform infrared spectrometer analysis were used. The optimum preconcentration conditions such as pH, eluent type, sample volume, sample flow rate and foreign ions effect were determined. The mean recovery and relative standard deviation values were found to be 100.7 ± 1.5 and 4.01% for Cd(II) ions. The capacity of the sorbent was obtained 277.8 mg g^-1 from the Langmuir isotherm model. The limit of detection was calculated as 0.216 µg L^-1 (P.F:40). In order to test the accuracy and applicability of the method, certified reference material and spiked water samples were analyzed. The results demonstrated good agreement with the certified values (relative error < 10%).

Safety assessment of graphene oxide and microcystin-LR complex: a toxicological scenario beyond physical mixture

Background

Nanomaterials have been widely used in electrochemistry, sensors, medicine among others applications, causing its inevitable environmental exposure. A raising question is the “carrier” effect due to unique surface properties of nanomaterials, which may collectively impact the bioavailability, toxicokinetic, distribution and biological effects of classic toxicants. Noteworthy, this aspect of information remains largely unexplored.

Methods

Here, we deliberately selected two entities to mimic this scenario. One is graphene oxide (GO), which is made in ton quantity with huge surface-area that provides hydrophilicity and π–π interaction to certain chemicals of unique structures. The other is Microcystin-LR (MCLR), a representative double-bond rich liver-toxic endotoxin widely distributed in aquatic-system. Firstly, the adsorption of GO and MCLR after meeting under environmental conditions was explored, and then we focused on the toxicological effect and related mechanism of GO-MCLR complex on human skin cutin forming cells (HaCaT cells) and normal liver cells (L02 cells).

Results

Abiotically, our study demonstrated that GO could effectively adsorb MCLR through hydrogen bonding and π–π interaction, the oxidation degree of GO-MCLR decreased significantly and surface defect level raised. Compared to GO or MCLR, GO-MCLR was found to induce more remarkable apoptosis and ferroptosis in both HaCaT and L02 cells. The underlying mechanism was that GO-MCLR induced stronger intracellular reactive oxygen species (ROS) and mtROS generation, followed by Fe²⁺ accumulation, mitochondrial dysfunction and cytoskeletal damage.

Conclusions

These results suggest that the GO-MCLR complex formed by GO adsorption of MCLR may exhibit more toxic effects than the single material, which demonstrates the necessity for assessing nano-toxicant complexity. Our discovery may serve as a new toxicological paradigm in which nanomaterial mediated surface adsorption effects could impact the degree of cytotoxicity and toxicological mechanisms of classic toxins.

Graphical Abstract

Supplementary Information

The online version contains supplementary material available at 10.1186/s12989-022-00466-x.