Photocatalytic synthesis of TiO(2) and reduced graphene oxide nanocomposite for lithium ion battery

High-Performance Lithium-Ion Batteries with High Stability Derived from Titanium-Oxide- and Sulfur-Loaded Carbon Spherogels

This study presents a novel approach to developing high-performance lithium-ion battery electrodes by loading titania-carbon hybrid spherogels with sulfur. The resulting hybrid materials combine high charge storage capacity, electrical conductivity, and core-shell morphology, enabling the development of next-generation battery electrodes. We obtained homogeneous carbon spheres caging crystalline titania particles and sulfur using a template-assisted sol-gel route and carefully treated the titania-loaded carbon spherogels with hydrogen sulfide. The carbon shells maintain their microporous hollow sphere morphology, allowing for efficient sulfur deposition while protecting the titania crystals. By adjusting the sulfur impregnation of the carbon sphere and varying the titania loading, we achieved excellent lithium storage properties by successfully cycling encapsulated sulfur in the sphere while benefiting from the lithiation of titania particles. Without adding a conductive component, the optimized material provided after 150 cycles at a specific current of 250 mA g-1 a specific capacity of 825 mAh g-1 with a Coulombic efficiency of 98%.

Decade Milestone Advancement of Defect-Engineered g-C3N4 for Solar Catalytic Applications

Over the past decade, graphitic carbon nitride (g-C3N4) has emerged as a universal photocatalyst toward various sustainable carbo-neutral technologies. Despite solar applications discrepancy, g-C3N4 is still confronted with a general fatal issue of insufficient supply of thermodynamically active photocarriers due to its inferior solar harvesting ability and sluggish charge transfer dynamics. Fortunately, this could be significantly alleviated by the "all-in-one" defect engineering strategy, which enables a simultaneous amelioration of both textural uniqueness and intrinsic electronic band structures. To this end, we have summarized an unprecedently comprehensive discussion on defect controls including the vacancy/non-metallic dopant creation with optimized electronic band structure and electronic density, metallic doping with ultra-active coordinated environment (M-Nx, M-C2N2, M-O bonding), functional group grafting with optimized band structure, and promoted crystallinity with extended conjugation π system with weakened interlayered van der Waals interaction. Among them, the defect states induced by various defect types such as N vacancy, P/S/halogen dopants, and cyano group in boosting solar harvesting and accelerating photocarrier transfer have also been emphasized. More importantly, the shallow defect traps identified by femtosecond transient absorption spectra (fs-TAS) have also been highlighted. It is believed that this review would pave the way for future readers with a unique insight into a more precise defective g-C3N4 "customization", motivating more profound thinking and flourishing research outputs on g-C3N4-based photocatalysis.

Simultaneous photocatalytic removal of organic dye and heavy metal from textile wastewater over N-doped TiO2 on reduced graphene oxide

Methylene blue (MB) and hexavalent chromium Cr(VI) are hazardous pollutants in textile waste and cannot be completely removed using conventional methods. So far, there have been no specific studies examining the synthesis and activity of N-TiO₂/rGO as a photocatalyst for removing MB and Cr(VI) from textile wastewater. This work especially highlights the synthesis of N-TiO₂/rGO as a photocatalyst which exhibits a wider range of light absorption and is highly effective for simultaneous removal of MB-Cr(VI) under visible light. Titanium tetrachloride (TiCl₄) was used as the precursor for N-TiO₂ synthesis using the sol-gel method. Graphite was oxidized using Hummer's method and reduced with hydrazine to produce rGO. N-TiO₂/rGO was synthesized using a hydrothermal process and then analyzed using several characterization instruments. The X-ray diffraction pattern (XRD) showed that the anatase N-TiO₂/rGO phase was detected at the diffraction peak of 2θ = 25.60°. Scanning electron microscopy and transmission electron microscopy (SEM-EDS and TEM) dispersive X-ray spectrometry images show that N-TiO₂ particles adhere to the surface of rGO with uniform size and N and Ti elements are present in the N-TiO₂/rGO combined investigated. Gas absorption analysis data (GSA) shows that N-TiO₂/rGO had a surface area of 77.449 m²/g, a pore volume of 0.335 cc/g, and a pore size of 8.655 nm. The thermogravimetric differential thermal analysis (TG-DTA) curve showed the anatase phase at 500-780 °C with a weight loss of 0.85%. The N-TiO₂/rGO composite showed a good photocatalyst application. The photocatalytic activity of N-TiO₂/rGO for textile wastewater treatment under visible light showed higher effectiveness than ultraviolet light, with 97.92% for MB and 97.48% for Cr(VI). Combining N-TiO₂ with rGO is proven to increase the light coverage in the visible light region. Removal of MB and Cr(VI) can be carried out simultaneously and results in a removal efficiency of 95.96%.

A Comprehensive Review on Adsorption, Photocatalytic and Chemical Degradation of Dyes and Nitro-Compounds over Different Kinds of Porous and Composite Materials

Dye and nitro-compound pollution has become a significant issue worldwide. The adsorption and degradation of dyes and nitro-compounds have recently become important areas of study. Different methods, such as precipitation, flocculation, ultra-filtration, ion exchange, coagulation, and electro-catalytic degradation have been adopted for the adsorption and degradation of these organic pollutants. Apart from these methods, adsorption, photocatalytic degradation, and chemical degradation are considered the most economical and efficient to control water pollution from dyes and nitro-compounds. In this review, different kinds of dyes and nitro-compounds, and their adverse effects on aquatic organisms and human beings, were summarized in depth. This review article covers the comprehensive analysis of the adsorption of dyes over different materials (porous polymer, carbon-based materials, clay-based materials, layer double hydroxides, metal-organic frameworks, and biosorbents). The mechanism and kinetics of dye adsorption were the central parts of this study. The structures of all the materials mentioned above were discussed, along with their main functional groups responsible for dye adsorption. Removal and degradation methods, such as adsorption, photocatalytic degradation, and chemical degradation of dyes and nitro-compounds were also the main aim of this review article, as well as the materials used for such degradation. The mechanisms of photocatalytic and chemical degradation were also explained comprehensively. Different factors responsible for adsorption, photocatalytic degradation, and chemical degradation were also highlighted. Advantages and disadvantages, as well as economic cost, were also discussed briefly. This review will be beneficial for the reader as it covers all aspects of dye adsorption and the degradation of dyes and nitro-compounds. Future aspects and shortcomings were also part of this review article. There are several review articles on all these topics, but such a comprehensive study has not been performed so far in the literature.

Graphene: Chemistry and Applications for Lithium-Ion Batteries

In the present era, different allotropes of carbon have been discovered, and graphene is the one among them that has contributed to many breakthroughs in research. It has been considered a promising candidate in the research and academic fields, as well as in industries, over the last decade. It has many properties to be explored, such as an enhanced specific surface area and beneficial thermal and electrical conductivities. Graphene is arranged as a 2D structure by organizing sp2 hybridized C with alternative single and double bonds, providing an extended conjugation combining hexagonal ring structures to form a honeycomb structure. The precious structure and outstanding characteristics are the major reason that modern industry relies heavily on graphene, and it is predominantly applied in electronic devices. Nowadays, lithium-ion batteries (LIBs) foremostly utilize graphene as an anode or a cathode, and are combined with polymers to use them as polymer electrolytes. After three decades of commercialization of the lithium-ion battery, it still leads in consumer electronic society due to its higher energy density, wider operating voltages, low self-discharge, noble high-temperature performance, and fewer maintenance requirements. In this review, we aim to give a brief review of the domination of graphene and its applications in LIBs.

Templated synthesis of 2D TiO2 nanoflakes for durable lithium ions battery

In this work, the 2D TiO2 nanoflakes were prepared by employing MXene as sacrificial template for durable lithium ions batteries (LIBs) anode. Essentially, the high crystalline anatase TiO2 nanoparticles compacted...

Minimal TiO2 Coupled with Conductive Polymer-Stimulated Synergistic Effect on Fast and Reversible Sodium-Ion Storage for Bismuth Sulfide

Designing multiphase composition is believed to availably boost the structural integrity and electrochemical properties of sodium-ion battery anodes. Herein, a conceive of nanoflowers, assembled with Bi₂S₃ nanorods, is demonstrated to construct the multiphase composition involving TiO₂ coating and polypyrrole (PPy) encapsulation. Bi₂S₃ acted as the dominating active material, in consideration of the low content of TiO₂, which ensured the high capacity of the composite. The dual-structural restrain of the TiO₂ and PPy coatings can effectively alleviate volume variation based on the pseudo-"zero-strain" effect of TiO₂ and high flexibility of PPy shells. Meanwhile, the heterointerface greatly enhanced the coupling effect between Bi₂S₃ and TiO₂ and thus improved the electrochemical performance, which was proved by the results of density functional theory calculation and electrochemical tests. Combining the regulation from the Bi₂S₃/TiO₂ heterojunction and the dual-structural restrain effect, the Bi₂S₃/TiO₂@PPy electrode exhibited excellent rate performance and superior cycle stability (275.8 mA h g^-1 over 500 cycles at 10 A g^-1). This study indicates that designing multiphase composition can be very promising and provides a structural insight to construct high stability in electrodes for sodium-ion batteries.

Non-noble metal plasmonic enhanced photoelectrochemical sensing of chlorpyrifos based on 1D TiO2-x/3D nitrogen-doped graphene hydrogel heterostructure

Low-cost and resource-rich non-noble metal plasmonic materials have attracted tremendous attention as potential substitutes for plasmonic noble metals. Herein, 3D nitrogen-doped graphene hydrogels (NGH) decorated with Ti³⁺ self-doped 1D rod-shaped titanium dioxide nanorods (TiO_2-x NR), 10-25 nm in size, were prepared by a facile one-step method. It was found that the as-fabricated TiO_2-x NR/NGH showed a synergistic effect, displaying enhanced photoelectrochemical (PEC) activity by controlling the nanoscale architecture and improving the electronic properties, while also producing abundant oxygen vacancies, which extended the light harvesting and suppressed the recombination of electron-hole pairs induced by the non-noble metal surface plasmon resonance (SPR) effect. In particular, the transient-state photocurrent intensity of the TiO_2-x NR/NGH composites was 5.1 times as high as that of pure TiO₂. Therefore, the TiO_2-x NR/NGH composites could serve as a substrate material for PEC sensing, providing a good basis for selective and sensitive detection of chlorpyrifos. Under optimal conditions, the constructed PEC sensor was found to have several advantages including a broad linear range (0.05 ng/mL-0.5 μg/mL), low detection limit (0.017 ng/mL), and considerable stability, demonstrating that the sensor may offer a promising route in the field of environmental analysis.

Enhanced visible light-driven photocatalysis of iron-oxide/titania composite: Norfloxacin degradation mechanism and toxicity study

A simulated visible light-mediated iron oxide-titania (IoT) nanocomposite was employed to degrade the antibiotic norfloxacin (NFN) photocatalytically. The photocatalyst were prepared using a sol-gel method with controlled titania loadings to iron oxide by altering the fabrications step. The nanocomposites were structurally characterized by field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), field emission high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, Diffuse reflectance UV-visible spectra (DRS-UV) spectroscopy, cyclic voltammetry, and X-ray photoelectron spectroscopy (XPS). It was observed that 100 mg/L of iron oxide doped titania loading at 1:4 (IoT-4) achieved the maximum photocatalytic activity in a 75 mg/100 mL of NFN solution within 60 min of the reaction time under visible light irradiation. The NFN degradation mechanism affirmed using HPLC-MS/MS analysis and the results confirmed the complete NFN degradation without residual intermediates. Significant, sustained recyclability was obtained by completely removing the contaminant up to 5 cycles with 90% degradation ability till nine cycles. Bacterial- and phytotoxicity data ascertain that the photocatalyzed and contaminant-free water is safe for the environment. The outstanding photocatalytic performance in removing organic pollutants indicates the potential application of IoT nanocomposites in real-time environmental remediation.

Ce2O3/BiVO4 Embedded in rGO as Photocatalyst for the Degradation of Methyl Orange under Visible Light Irradiation

A p–n heterojunction semiconductor structure composed of Ce3O4 and BiVO4 has been synthesized and then incorporated into reduced graphene oxide (rGO) by the hydrothermal method. The ternary composites were characterized by X-ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM), electron diffraction spectroscopy (EDS), and UV–vis spectroscopy. The efficiency of the composites as photocatalysts was determined by studying the oxidative degradation of methyl orange in aqueous solution under visible light irradiation. The effect of parameters such as pH, catalyst loading, and concentration of the dye solution was examined in order to determine their influence on the photocatalytic activity of the composites. The composite incorporated into reduced graphene oxide presented the highest percentage (above 90%) in 2 h time, attributed to the effect of the increased surface area. The process of the enhanced photocatalytic activity has been discussed based on the energy band positions of the nanoparticles within the composite.

Hybrid carbon spherogels: carbon encapsulation of nano-titania

Extraordinarily homogeneous, freestanding titania-loaded carbon spherogels can be obtained using Ti(acac)₂(OiPr)₂ in the polystyrene sphere templated resorcinol-formaldehyde gelation. Thereby, a distinct, crystalline titania layer is achieved inside every hollow sphere building unit. These hybrid carbon spherogels allow capitalizing on carbon's electrical conductivity and the lithium-ion intercalation capacity of titania.

Improved lithium-ion battery performance by introducing oxygen-containing functional groups by plasma treatment

Metal sulfides are often used as cathode materials for lithium-ion batteries (LIBs) owing to their high theoretical specific capacity; however, excessively fast capacity decay during charging/discharging and rapid shedding during cycling limits their practical application in batteries. In this study, we proposed a strategy using plasma treatment combined with the solvothermal method to prepare cobalt sulfide (Co_1-xS)-carbon nanofibers (CNFs) composite. The plasma treatment could introduce oxygen-containing polar groups and defects, which could improve the hydrophilicity of the CNFs for the growth of the Co_1-xS, thereby increasing the specific capacity of the composite electrode. The results show that the composite electrode present a high discharge specific capacity (839 mAh g^-1at a current density of 100 mA g^-1) and good cycle stability (the capacity retention rate almost 100% at 2000 mA g^-1after 500 cycles), attributing to the high conductivity of the CNFs. This study proves the application of plasma treatment and simple vulcanization method in high-performance LIBs.

Magnetic ZnO Crystal Nanoparticle Growth on Reduced Graphene Oxide for Enhanced Photocatalytic Performance under Visible Light Irradiation

Magnetite zinc oxide (MZ) (Fe₃O₄/ZnO) with different ratios of reduced graphene oxide (rGO) was synthesized using the solid-state method. The structural and optical properties of the nanocomposites were analyzed using transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, Fourier-transform infrared spectroscopy (FTIR), ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis/DRS), and photoluminescence (PL) spectrophotometry. In particular, the analyses show higher photocatalytic movement for crystalline nanocomposite (MZG) than MZ and ZnO nanoparticles. The photocatalytic degradation of methylene blue (MB) with crystalline ZnO for 1.5 h under visible light was 12%. By contrast, the photocatalytic activity for MZG was more than 98.5%. The superior photocatalytic activity of the crystalline nanocomposite was detected to be due to the synergistic effect between magnetite and zinc oxide in the presence of reduced graphene oxide. Moreover, the fabricated nanocomposite had high electron-hole stability. The crystalline nanocomposite was stable when the material was used several times.

Reduced Graphene Oxide-Laminated One-Dimensional TiO2-Bronze Nanowire Composite: An Efficient Photoanode Material for Dye-Sensitized Solar Cells

A facile one-step hydrothermal method was developed to prepare reduced graphene oxide-laminated TiO₂-bronze (TiO₂-B) nanowire composites (TNWG), which contain two-dimensional graphene oxide nanosheets and TiO₂-B nanowires. In the hydrothermal process, the functional groups of graphene oxide were reduced significantly. Dye-sensitized solar cells (DSSCs) were fabricated using TNWG as the photoanode material. The effects of different reduced graphene oxide contents in TNWG on the energy conversion efficiency of the dye-sensitized solar cells were investigated using J-V and incident photon-to-current conversion efficiency characteristics. DSSCs based on a TNWG hybrid photoanode with a reduced graphene oxide content of 8 wt % demonstrated an overall light-to-electricity conversion efficiency of 4.95%, accompanied by a short-circuit current density of 10.41 mA cm^-2, an open-circuit voltage of 0.71 V, and a fill factor of 67%, which were much higher than those of DSSC made with a pure TiO₂-B NW-based photoanode. The overall improvement in photovoltaic performance could be associated to the intense visible light absorption and enhanced dye adsorption because of the increased surface area of the composite, together with faster electron transport due to reduced carrier recombination.

Photocatalytic performance improvement by utilizing GO_MWCNTs hybrid solution on sand/ZnO/TiO2-based photocatalysts to degrade methylene blue dye

In this work, sand/zinc oxide (ZnO)/titanium dioxide (TiO₂)-based photocatalysts were hybridized with graphene oxide (GO) and GO_multi-walled carbon nanotubes (MWCNTs) hybrid solution. The novel hybrid was then used in photocatalysis to degrade dye contamination. The nanocomposite photocatalyst was initially fabricated by growing ZnO nanorods (NRs) via sol-gel immersion followed by synthesizing TiO₂ NRs for different times (5 and 20 h) using a hydrothermal method on sand as a substrate. Prior to the hybridization, the initial GO was synthesized using electrochemical exfoliation and further mixed with 1 wt% MWCNTs to form GO_MWCNTs hybrid solution. The synthesized GO and GO_MWCNTs hybrid solution were then incorporated onto sand/ZnO/TiO₂ nanocomposite-based photocatalysts through immersion. Various sand/ZnO/TiO₂-based photocatalysts were then tested for methylene blue (MB) dye degradation within 3 days. On the basis of UV-Vis measurement, the highest MB degradation was achieved by using sand/ZnO NRs/TiO₂ NRs (5 h)/GO_MWCNTs (92.60%). The high surface area and high electrical conductivity of GO_MWCNTs prolonged the lifetime of electron/hole separation and thus enhanced the photocatalytic performance.

Selective nanomolar electrochemical detection of serotonin, dopamine and tryptophan using TiO2/RGO/CPE – influence of reducing agents

TiO2/RGO nanocomposites were synthesised via a simple one-pot hydrothermal method and used as a modifier in carbon paste electrode for the sensitive determination of serotonin.

Ultrathin 2D Mesoporous TiO2 /rGO Heterostructure for High-Performance Lithium Storage

Lithium-ion batteries (LIBs) have been widely applied and studied as an effective energy supplement for a variety of electronic devices. Titanium dioxide (TiO₂ ), with a high theoretical capacity (335 mAh g^-1 ) and low volume expansion ratio upon lithiation, has been considered as one of the most promising anode materials for LIBs. However, the application of TiO₂ is hindered by its low electrical conductivity and slow ionic diffusion rate. Herein, a 2D ultrathin mesoporous TiO₂ /reduced graphene (rGO) heterostructure is fabricated via a layer-by-layer assembly process. The synergistic effect of ultrathin mesoporous TiO₂ and the rGO nanosheets significantly enhances the ionic diffusion and electron conductivity of the composite. The introduced 2D mesoporous heterostructure delivers a significantly improved capacity of 350 mAh g^-1 at a current density of 200 mA g^-1 and excellent cycling stability, with a capacity of 245 mAh g^-1 maintained over 1000 cycles at a high current density of 1 A g^-1 . The in situ transmission electron microscopy analysis indicates that the volume of the as-prepared 2D heterostructures changes slightly upon the insertion and extraction of Li⁺ , thus contributing to the enhanced long-cycle performance.

Crystallization of TiO2-MoS2 Hybrid Material under Hydrothermal Treatment and Its Electrochemical Performance

Hydrothermal crystallization was used to synthesize an advanced hybrid system containing titania and molybdenum disulfide (with a TiO₂:MoS₂ molar ratio of 1:1). The way in which the conditions of hydrothermal treatment (180 and 200 °C) and thermal treatment (500 °C) affect the physicochemical properties of the products was determined. A physicochemical analysis of the fabricated materials included the determination of the microstructure and morphology (scanning and transmission electron microscopy—SEM and TEM), crystalline structure (X-ray diffraction method—XRD), chemical surface composition (energy dispersive X-ray spectroscopy—EDS) and parameters of the porous structure (low-temperature N₂ sorption), as well as the chemical surface concentration (X-ray photoelectron spectroscop—XPS). It is well known that lithium-ion batteries (LIBs) represent a renewable energy source and a type of energy storage device. The increased demand for energy means that new materials with higher energy and power densities continue to be the subject of investigation. The objective of this research was to obtain a new electrode (anode) component characterized by high work efficiency and good electrochemical properties. The synthesized TiO₂-MoS₂ material exhibited much better electrochemical stability than pure MoS₂ (commercial), but with a specific capacity ca. 630 mAh/g at a current density of 100 mA/g.

Intercalation of Carbon Nanosheet into Layered TiO2 Grain for Highly Interfacial Lithium Storage

Interfacial energy storage contributes a new mechanism to the emergence of energy storage devices with not only a high-energy density of batteries but also a high-power density of capacitors. In this study, success was achieved in preparing a highly ordered two-dimensional (2D) carbon/TiO₂ (C/TiO₂) nanosheet composite using commercially available organic molecules with multifunctional groups and taking advantage of the wedge effects, oxidative polymerization, and carbonization. An experiment was conducted to validate the excellent performance of this 2D composite with respect to interfacial energy storage. The coin cell with 2D C/TiO₂ nanosheet composite demonstrates a specific capacity of as high as 510 mAh g^-1 and a high specific energy of 390.9 Wh kg^-1 at a specific power of 75.9 W kg^-1 with a current density of 0.1 A g^-1, and it also remains 39.0 Wh kg^-1 at a specific power of 8.2 kW kg^-1 with a high current density of 12.8 A g^-1. The excellent electrochemical performance can be attributed to the superior artificial interface capacitive Li⁺ storage capability, which would bridge the energy and power density gap between batteries and capacitors. Meanwhile, there are two varieties of carbon derivatives, 2D carbon nanosheet stacks and exfoliated carbon nanosheets, which can be obtained by wet-chemical etching and mechanical peeling. The experimental route is simple from commercially available raw materials, and it could be scalable at a low cost and large scale, which makes it suitable for application in various fields such as energy storage, nanocatalysis, sensors, and so on.

Two novel sets of UiO-66@ metal oxide/graphene oxide Z-scheme heterojunction: Insight into tetracycline and malathion photodegradation

Nowadays, widespread researches have been focused on the development of effective photocatalysts to remove pollutants of the aquatic system. In accordance with the universal studies, two new sets of UiO-66@ metal oxide (including ZnO and TiO₂)/graphene oxide heterojunctions were synthesized for photodegradation of aromatic (tetracycline) and nonaromatic (malathion) pollutants which are challenging cases in the environment. The dosage of the photocatalyst, pH of the solution, the type of metal oxide, and the presence of various scavengers are assayed parameters in this work. In the optimum condition, maximum photodegradation efficiency is achieved in 90 min for tetracycline (81%) and malathion (100%) by the UiO-66@ZnO/graphene oxide. The superior separation of charge carriers by Z-scheme mechanism, excellent electron mobility on layers of graphene oxide and high surface area are factors that enhanced the efficiency. Furthermore, in comparison with pure UiO-66, the band gaps belong to heterojunctions revealed a red shift in the absorption edge, which can be responsible for more expand adsorption of the solar spectrum. Total organic carbon analysis verified the decontamination of these pollutants in the solution. The produced main intermediates during the photocatalytic process were identified and the possible degradation pathway proposed. In general, the superior photocatalytic activity suggests that these designed photocatalysts can be a promising choice for having a clean future.

3.3 nm-sized TiO2/carbon hybrid spheres endowed with pseudocapacitance-dominated superhigh-rate Li-ion and Na-ion storage

Decreasing the particle size of nanoscaled battery materials will induce amazing enhancement effects on their charging rates, which holds a promise to overcome the common bottleneck of the low charging rates of batteries. However, the fabrication of ultrafine-sized battery materials remains a great challenge. Herein, 3.3 nm-sized anatase TiO2 particles embedded in electrically and ionically conductive carbon spheres have been designed and fabricated via the suppression of Ostwald ripening with the aim to obtain insight into the electrochemical behaviors of ultrafine-sized materials. The pseudocapacitive and diffusion-controlled intercalative characteristics of the 3.3 nm-sized TiO2/carbon hybrid spheres for Li-ion and Na-ion storage have been systematically investigated via a cyclic voltammetry (CV) method combined with a differential capacitance method that is introduced here for the first time to analyze battery materials. CV and galvanostatic voltage profiles demonstrate that pseudocapacitance dominates the charge storage and increases with cycling for both Li-ion and Na-ion storage. Capacitance accounts for >83% of the Li-ion storage. A specific pseudocapacitance of 558 F g-1 with a window voltage of ∼2 V in carbonate electrolyte has been achieved. The reversible capacity is higher than the theoretical capacity of TiO2 after 600 discharge/charge cycles at 2 C and maintains ∼60% of that of TiO2 even at 80 C (45 s for full discharge or charge). For Na-ion storage, a high cycliability of 2500 discharge/charge cycles has been obtained at 2 C. Capacitance accounts for ∼79% of the Na-ion storage with cycling. Ultrafine-sized materials are very promising electrode candidates for constructing pseudocapacitive batteries possessing both high energy and power densities.

Two-Dimensional Layered Ultrathin Carbon/TiO2 Nanosheet Composites for Superior Pseudocapacitive Lithium Storage

Intercalation of carbon nanosheets into two-dimensional (2D) inorganic materials could enhance their properties in terms of mechanics and electrochemistry, but sandwiching these two kinds of materials in an alternating sequence is a great challenge in synthesis. Herein, we report a novel strategy to construct TiO₂ nanosheets into 2D pillar-layer architectures by employing benzidine molecular assembly as pillars. Then, 2D carbon/TiO₂ nanosheet composite with a periodic interlayer distance of 1.1 nm was obtained following a polymerization and carbonization process. This method not only alleviates the strain arising from the torsion of binding during carbonization but also hinders the structural collapse of TiO₂ due to the intercalation of the carbon layer by rational control of annealing conditions. The composite material possesses a large carbon/TiO₂ interface, providing abundant active sites for ultrafast pseudocapacitive charge storage, thus displaying a superior high-rate performance with a specific capacity of 67.8 mAh g^-1 at a current density of 12.8 A g^-1 based on the total electrode and excellent cyclability with 87.4% capacity retention after 3000 cycles.

In situ construction of hybrid MnO2@GO heterostructures for enhanced visible light photocatalytic, anti-inflammatory and anti-oxidant activity

Hybrid MnO₂@GO heterostructure nano-composites with enhanced visible light photocatalytic, anti-oxidant and anti-inflammatory activity.

Ab Initio Study of SOF2 and SO2F2 Adsorption on Co-MoS2

The detection of partial discharge by analyzing the decomposition components of SF6 gas in gas-insulated switchgears plays an important role in the diagnosis and assessment of the operational state of power equipment. Recently, the application of transition metal-modified MoS2 monolayer dioxide in gas detection has received wide attention. In this paper, first-principle density functional theory calculations were adopted to study the gas-sensitive response of Co-MoS2 monolayer to SOF2 and SO2F2. It is found that the conductivity of the Co-MoS2 monolayer has been effectively enhanced after Co atom doping on the MoS2 monolayer. After gas adsorption, electrons transfer from the Co-MoS2 monolayer to the gas molecules, resulting in significant reduction of conductivity of the adsorption system. The calculation results reveal that the Co-MoS2 monolayer is sensitive and selective to SOF2 and SO2F2 gases. This study provides the theoretical possibility of using Co-MoS2 as a gas sensor for SOF2 and SO2F2 gas detection.

Novel magnetic Fe3O4@rGO@ZnO onion-like microspheres decorated with Ag nanoparticles for the efficient photocatalytic oxidation of metformin: toxicity evaluation and insights into the mechanisms

Emerging water contaminants, including pharmaceutical and personal care products, have become a major concern in water pollution, and several efforts have been made for the efficient removal of these contaminants.

A hierarchical porous architecture of silicon@TiO2@carbon composite novel anode materials for high performance Li-ion batteries

The excellent electrochemical properties are attributed to the synergistic action of hierarchical porous TiO₂ and carbon layers.

Titanium Dioxide/Graphene and Titanium Dioxide/Graphene Oxide Nanocomposites: Synthesis, Characterization and Photocatalytic Applications for Water Decontamination

The use of titanium dioxide, TiO2 as a photocatalyst in water decontamination has witnessed continuous interest due to its efficiency, stability, low toxicity and cost-effectiveness. TiO2 use is limited by its large band gap energy leading to light absorbance in the UV region of the spectrum, and by the relatively fast rate of recombination of photogenerated electrons and positive holes. Both limitations can be mitigated by using carbon-TiO2 nanocomposites, such as those based on graphene (G) and graphene oxide (GO). Relative to bare TiO2, these nanocomposites have improved photocatalytic activity and stability under the UV–visible light, constituting a promising way forward for improved TiO2 photocatalytic performance. This review focuses on the recent developments in the chemistry of TiO2/G and TiO2/GO nanocomposites. It addresses the mechanistic fundamentals, briefly, of TiO2 and TiO2/G and TiO2/GO photocatalysts, the various synthesis strategies for preparing TiO2/G and TiO2/GO nanocomposites, and the different characterization techniques used to study TiO2/G and TiO2/GO nanocomposites. Some applications of the use of TiO2/G and TiO2/GO nanocomposites in water decontamination are included.

Polymer-Promoted Synthesis of Porous TiO2 Nanofibers Decorated with N-Doped Carbon by Mechanical Stirring for High-Performance Li-Ion Storage

Extensive efforts have been devoted to developing simple, low-cost, and high-production-yield methods to prepare hybrid materials with desired structural features for high-performance lithium storage. Here, a novel strategy is reported for fabricating the porous TiO₂ nanofibers decorated with N-doped carbon (TiO₂/C nanofibers) by a combination of mechanical stirring and the addition of a polymer in a beaker at ambient temperature, followed by calcination. The mechanical stirring process can provide homogeneous mixing of reactants in a solution, whereas the polymer acts not only as a structure-directing agent for fabricating one-dimensional nanofibers but also as the carbon and nitrogen source to generate N-doped carbon framework and porous structures. The TiO₂/C nanofibers have average diameters of 500 nm and lengths up to 65 μm and are further composed of intercrossed TiO₂ nanocrystals with sizes of 8 nm, with micropores centered at 1.5 nm and mesopores at 3-6 nm. The TiO₂/C electrodes demonstrated a high reversible capacity (368 mAh g^-1 at 0.25C after 200 cycles), good cycling performance (176 mAh g^-1 at 10C over 2000 cycles), and excellent rate capability (97 mAh g^-1 at 20C).

RGO-Coated TiO2 Microcones for High-Rate Lithium-Ion Batteries

Reduced graphene oxide (RGO)-coated TiO₂ microcones have been synthesized via simple anodization and cyclic voltammetry for use in lithium-ion batteries (LIBs). Microcones had a perpendicularly oriented hollow core, an anatase structure, and a high surface area, allowing higher capacity than other nanosized TiO₂ structures. TiO₂ has low electrical conductivity, leading to the limitation of fast charging and high capacity; however, this was improved by the application of an RGO coating in this work. As anode materials of LIB, the obtained RGO microcone showed a capacity of 157 mAh g^-1 at 10C (fully charged within ∼360 s) and sustained 1000 cycles with only 0.02% capacity fading per cycle. The capacity was 1.5 times higher than that of conventional microcone. We speculated that the decrease in the charge-transfer resistance (R _ct) played a crucial role in increasing the capacity with fast charging.

Exploring Chemical, Mechanical, and Electrical Functionalities of Binders for Advanced Energy-Storage Devices

Tremendous efforts have been devoted to the development of electrode materials, electrolytes, and separators of energy-storage devices to address the fundamental needs of emerging technologies such as electric vehicles, artificial intelligence, and virtual reality. However, binders, as an important component of energy-storage devices, are yet to receive similar attention. Polyvinylidene fluoride (PVDF) has been the dominant binder in the battery industry for decades despite several well-recognized drawbacks, i.e., limited binding strength due to the lack of chemical bonds with electroactive materials, insufficient mechanical properties, and low electronic and lithium-ion conductivities. The limited binding function cannot meet inherent demands of emerging electrode materials with high capacities such as silicon anodes and sulfur cathodes. To address these concerns, in this review we divide the binding between active materials and binders into two major mechanisms: mechanical interlocking and interfacial binding forces. We review existing and emerging binders, binding technology used in energy-storage devices (including lithium-ion batteries, lithium-sulfur batteries, sodium-ion batteries, and supercapacitors), and state-of-the-art mechanical characterization and computational methods for binder research. Finally, we propose prospective next-generation binders for energy-storage devices from the molecular level to the macro level. Functional binders will play crucial roles in future high-performance energy-storage devices.

Homogeneous growth of TiO2-based nanotubes on nitrogen-doped reduced graphene oxide and its enhanced performance as a Li-ion battery anode

The pursuit of a promising replacement candidate for graphite as a Li-ion battery anode, which can satisfy both engineering criteria and market needs has been the target of researchers for more than two decades. In this work, we have investigated the synergistic effect of nitrogen-doped reduced graphene oxide (NrGO) and nanotubular TiO₂ to achieve high rate capabilities with high discharge capacities through a simple, one-step and scalable method. First, nanotubes of hydrogen titanate were hydrothermally grown on the surface of NrGO sheets, and then converted to a mixed phase of TiO₂-B and anatase (TB) by thermal annealing. Specific surface area, thermal gravimetric, structural and morphological characterizations were performed on the synthesized product. Electrochemical properties were investigated by cyclic voltammetry and cyclic charge/discharge tests. The prepared anode showed high discharge capacity of 150 mAh g^-1 at 1 C current rate after 50 cycles. The promising capacity of synthesized NrGO-TB was attributed to the unique and novel microstructure of NrGO-TB in which long nanotubes of TiO₂ have been grown on the surface of NrGO sheets. Such architecture synergistically reduces the solid-state diffusion distance of Li⁺ and increases the electronic conductivity of the anode.

Investigation of amino-grafted TiO2/reduced graphene oxide hybrids as a novel photocatalyst used for decomposition of selected organic dyes

A novel type of photocatalyst - hybrids of amino-grafted titania and reduced graphene oxide - was synthesized by a hydrothermal method. The hybrids were comprehensively analyzed, including determination of their morphology (TEM), porous structure parameters (low-temperature N₂ sorption) and crystalline structure (XRD). Additionally, to confirm the effective bonding of the amino-grafted titania and reduced graphene oxide, Raman and X-ray photoelectron spectroscopy (XPS) were used, in addition to elemental analysis. The key stage of the research was an evaluation of the photocatalytic activity of the synthesized hybrid photocatalysts with respect to the decomposition of C.I. Basic Blue 9 and C.I. Basic Red 1 dyes. It was found that the amino-grafted titania/reduced graphene oxide hybrids exhibited better photocatalytic activity in the degradation of C.I. Basic Blue 9 and C.I. Basic Red 1 than amino-grafted TiO₂ alone. The high efficiency of dye decomposition can be attributed to the higher BET surface area and good separation of photogenerated electrons and holes offered by graphene oxide.

Graphene Modified TiO₂ Composite Photocatalysts: Mechanism, Progress and Perspective

Graphene modified TiO₂ composite photocatalysts have drawn increasing attention because of their high performance. Some significant advancements have been achieved with the continuous research, such as the corresponding photocatalytic mechanism that has been revealed. Specific influencing factors have been discovered and potential optimizing methods are proposed. The latest developments in graphene assisted TiO₂ composite photocatalysts are abstracted and discussed. Based on the primary reasons behind the observed phenomena of these composite photocatalysts, probable development directions and further optimizing strategies are presented. Moreover, several novel detective technologies-beyond the decomposition test-which can be used to judge the photocatalytic performances of the resulting photocatalysts are listed and analyzed. Although some objectives have been achieved, new challenges still exist and hinder the widespread application of graphene-TiO₂ composite photocatalysts, which deserves further study.

Cobalt Nanoparticles Chemically Bonded to Porous Carbon Nanosheets: A Stable High-Capacity Anode for Fast-Charging Lithium-Ion Batteries

A two-dimensional electrode architecture of ∼25 nm sized Co nanoparticles chemically bonded to ∼100 nm thick amorphous porous carbon nanosheets (Co@PCNS) through interfacial Co-C bonds is reported for the first time. This unique 2D hybrid architecture incorporating multiple Li-ion storage mechanisms exhibited outstanding specific capacity, rate performance, and cycling stabilities compared to nanostructured Co₃O₄ electrodes and Co-based composites reported earlier. A high discharge capacity of 900 mAh/g is achieved at a charge-discharge rate of 0.1C (50 mA/g). Even at high rates of 8C (4 A/g) and 16C (8 A/g), Co@PCNS demonstrated specific capacities of 620 and 510 mAh/g, respectively. Integrity of interfacial Co-C bonds, Co nanoparticles, and 90% of the initial capacity are preserved after 1000 charge-discharge cycles. Implementation of Co nanoparticles instead of Co₃O₄ restricted Li₂O formation during the charge-discharge process. In situ formed Co-C bonds during the pyrolysis steps improve interfacial charge transfer, and eliminate particle agglomeration, identified as the key factors responsible for the exceptional electrochemical performance of Co@PCNS. Moreover, the nanoporous microstructure and 2D morphology of carbon nanosheets facilitate superior contact with the electrolyte solution and improved strain relaxation. This study summarizes design principles for fabricating high-performance transition-metal-based Li-ion battery hybrid anodes.

Reduced graphene oxide/BiFeO3 nanohybrids-based signal-on photoelectrochemical sensing system for prostate-specific antigen detection coupling with magnetic microfluidic device

A novel magnetic controlled photoelectrochemical (PEC) sensing system was designed for sensitive detection of prostate-specific antigen (PSA) using reduced graphene oxide-functionalized BiFeO₃ (rGO-BiFeO₃) as the photoactive material and target-triggered hybridization chain reaction (HCR) for signal amplification. Remarkably enhanced PEC performance could be obtained by using rGO-BiFeO₃ as the photoelectrode material due to its accelerated charge transfer and improved the visible light absorption. Additionally, efficient and simple operation could be achieved by introducing magnetic controlled flow-through device. The assay mainly involved in anchor DNA-conjugated magnetic bead (MB-aDNA), PSA aptamer/trigger DNA (Apt-tDNA) and two glucose oxidase-labeled hairpins (H1-GOx and H2-GOx). Upon addition of target PSA, the analyte initially reacted with the aptamer to release the trigger DNA, which partially hybridized with the anchor DNA on the MB. Thereafter, the unpaired trigger DNA on the MB opened the hairpin DNA structures in sequence and propagated a chain reaction of hybridization events between two alternating hairpins to form a long nicked double-helix with numerous GOx enzymes on it. Subsequently, the enzymatic product (H₂O₂) generated and consumed the photo-excited electrons from rGO-BiFeO₃ under visible light irradiation to enhance the photocurrent. Under optimal conditions, the magnetic controlled PEC sensing system exhibited good photocurrent responses toward target PSA within the linear range of 0.001 - 100ng/mL with a detection limit of 0.31pg/mL. Moreover, favorable selectivity, good stability and satisfactory accuracy were obtained. The excellent analytical performance suggested that the rGO-BiFeO₃-based PEC sensing platform could be a promising tool for sensitive, efficient and low cost detection of PSA in disease diagnostics.

Self-Climbed Amorphous Carbon Nanotubes Filled with Transition Metal Oxide Nanoparticles for Large Rate and Long Lifespan Anode Materials in Lithium Ion Batteries

A composed material of amorphous carbon nanotubes (ACNTs) and encapsulated transition metal oxide (TMOs) nanoparticles was prepared by a common thermophysics effect, which is named the Marangoni effect, and a simple anneal process. The prepared ropy solution would form a Marangoni convection and climb into the channel of anodic aluminum oxide template (AAO) spontaneously. The ingenious design of the preparation method determined a distinctive structure of TMOs nanoparticles with a size of ∼5 nm and amorphous carbon coated outside full in the ACNTs. Here we prepared the ferric oxide (Fe₂O₃) nanoparticles and Fe₂O₃ mixed with manganic oxide (Fe₂O₃&Mn₂O₃) nanoparticles encapsulated in ACNTs as two anode materials of lithium ion batteries' the TMOs-filled ACNTs presented an evolutionary electrochemical performance in some respects of highly reversible capacity and excellent cycling stability (880 mA h g^-1 after 150 cycles).